| Most common failures | No# failures |
|---|
| Brakes imbalanced across an axle | 31 |
| Brake pipe excessively corroded | 30 |
| Windscreen wiper does not clear the windscreen effectively | 30 |
| Windscreen washer not working | 24 |
| Headlamp aim out of alignment | 24 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 22 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 15 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 14 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 13 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 12 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 12 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 10 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 10 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 9 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 9 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 8 |
| Horn not working (7.7 (a)) | 8 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 8 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 8 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 8 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 7 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 7 |
| Registration plate lamp issues | 7 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 7 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 7 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 6 |
| Rear Exhaust system insecure (6.1.2 (a)) | 6 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 6 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 5 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 5 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 5 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 5 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 5 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 5 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 5 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 5 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 5 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 4 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 4 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 4 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 4 |
| Emissions not tested (8.2.1.2 (d)) | 4 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 4 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 4 |
| Offside Rear Shock absorbers has a serious fluid leak | 4 |
| Nearside Rear Shock absorbers has a serious fluid leak | 4 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 4 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 4 |
| Registration plate issues | 3 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Parking brake: efficiency below requirements |3.7.B.7| | 3 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 3 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 3 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Offside Rear Service brake lagging in operation (1.2.1 (d)) | 3 |
| Power steering component leaking (2.1.5 (a)) | 3 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 3 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 3 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 3 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 3 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 3 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Emissions unable to be completed (8.2.1.2 (d)) | 3 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 3 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 2 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Rear parking brake recording little or no effort | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 2 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 2 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 2 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 2 |
| Nearside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt Track rod end (5.3.4 (b) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 2 |
| Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Offside Rear Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 2 |
| Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 2 |
| Rear fog lamp emits a light other than red |1.3.2e| | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 2 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Brake performance not tested (1.2.1 (g)) | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt split. (2.1.3 (g) (ii)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt split. (2.1.3 (g) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Emissions not tested due to exhaust leak (8.2.1.2 (d)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chalked in yellow (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension rod ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Central Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced x2 holes in boot floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Power steering component leaking steering rack gaitor leaking (2.1.5 (a)) | 1 |
| Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
| Front Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Nearside Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Rear brake binding | 1 |
| Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt arm, both. (5.3.4 (b) (ii)) | 1 |
| Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
| Parking brake lever ratchet mechanism worn to the extent that the brake may inadvertently release (1.1.6 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at front lower of wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Steering locking device missing pin missing from track rod end nut (2.1.3 (d)) | 1 |
| Offside Front Steering locking device missing pin missing from track rod end nut (2.1.3 (d)) | 1 |
| Rear Service brake imbalanced across an axle (1.2.1 (b) (i)) | 1 |
| Offside Front Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Offside Front Suspension component likely to become detached lower ball joint nut not a locking nut (5.3.3 (a) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded and floor corroded O/S/F (6.2.2 (d) (i)) | 1 |
| Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected nearside sill corroded (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill corroded (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill fully corroded (5.3.6 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre outer sill (7.1.1 (a) (i)) | 1 |
| Offside Power steering component leaking rack end seal (2.1.5 (a)) | 1 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Exhaust system insecure Rear silencer (6.1.2 (a)) | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Front Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Front passenger door cannot be opened from outside the vehicle unable to open from inside or out (6.2.3 (a)) | 1 |
| Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt o/s front outer loose large end (6.1.7 (g) (ii)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced o/s outer sill holed (6.1.1 (c) (i)) | 1 |
| Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt o/s front (2.1.3 (g) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan (5.3.6 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Nearside Front Seat belt not functioning as intended twisted (7.1.2 (c)) | 1 |
| Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced marked yellow (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced marked yellow (6.1.1 (c) (i)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Front Headlamp not working on main beam both (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Power steering component leaking in rack area (2.1.5 (a)) | 1 |
| Offside Rear fog lamp lens defective such that emitted light is adversely affected showing white light (4.5.1 (b) (ii)) | 1 |
| Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases box (6.1.2 (a)) | 1 |
| Emissions not tested because of exhaust blow (8.2.1.2 (d)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill, front & rear (5.3.6 (a) (i)) | 1 |
| Nearside Steering locking device missing track rod end (2.1.3 (d)) | 1 |
| Offside Steering locking device missing track rod end (2.1.3 (d)) | 1 |
| Front Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marked in yellow chalk (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marked in yellow chalk (6.2.2 (d) (i)) | 1 |
| Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spare wheel well corroded and holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt webbing significantly weakened cut from edge greater than 2mm (7.1.2 (b)) | 1 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Nearside Front Seat belt retracting mechanism defective Front Passenger (7.1.2 (e)) | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Offside Front Seat belt anchorage loose not fixed (7.1.1 (b)) | 1 |
| Offside Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill area (6.1.1 (c) (i)) | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Rear fog lamp adversely affected by the operation of another lamp (4.5.4 (b)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Nearside Side repeater likely to become detached (4.4.1 (c) (ii)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn rear bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Steering locking device missing track rod end (2.1.3 (d)) | 1 |
| Nearside Front Outer Steering rack gaiter missing or no longer prevents the ingress of dirt insecure (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength trailing arm (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Jacking point / Outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Centre outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt new clip fitted (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Offside Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Power steering component leaking Steering rack (2.1.5 (a)) | 1 |
| Front Service brake excessively binding both brakes (1.2.1 (f)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to sill (6.2.2 (d) (i)) | 1 |
| Exhaust system insecure Rear exhaust hangers (6.1.2 (a)) | 1 |
| Steering rack insecure to the extent there is excessive movement at the mountings (2.1.3 (a) (ii)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength next to trailing arm mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area is inadequately repaired sill repair patch does not meet requirements (5.3.6 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Front Fuel hose leaking (6.1.3 (b) (i)) | 1 |
| Emissions not tested exhaust blowing and misfire present (8.2.1.2 (d)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt -split (6.1.7 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases hole in front pipe (6.1.2 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor/sill severly corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner edge/wheel arch (5.3.6 (a) (i)) | 1 |
| Oil leaking excessively from engine oil leak [bad] (8.4.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL HOLED AND CORRODED (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced REAR PANEL HOLED AND CORRODED (6.1.1 (c) (i)) | 1 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Offside Rear Rear fog lamp switch missing (4.5.3 (a)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL HOLED & CORRODED (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Shock absorbers insecurely attached (5.3.2 (a) (i)) | 1 |
| Nearside Lower Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill (6.2.2 (d) (ii)) | 1 |
| Offside Lower Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill (6.2.2 (d) (ii)) | 1 |
| Offside Rear Lower Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Brake drum back plate insecure (1.1.14 (d)) | 1 |
| Emissions not tested (8.2.2.2 (e)) | 1 |
| Offside Front Brake hose excessively twisted (1.1.12 (b) (ii)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch front corner holed and corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Offside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases rear joining (6.1.2 (a)) | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn Chalked (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension arm pin or bush excessively worn Chalked (5.3.4 (a) (i)) | 1 |
| Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength With in 30 cm of top mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Within 30cm of lower suspension suspension arm mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer seal (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced With in 30cm of the drivers seat anchorage point (6.1.1 (c) (i)) | 1 |
| Emissions unable to be completed Major exhaust leak (8.2.1.2 (d)) | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill near suspension arm mount (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill near suspension arm mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill near axle mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill near axle mount (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt Split. (6.1.7 (g) (ii)) | 1 |
| Nearside Front Outer Suspension arm ball joint dust cover no longer prevents the ingress of dirt Split/Perished. (5.3.4 (b) (ii)) | 1 |
| Offside Front Outer Suspension arm ball joint dust cover no longer prevents the ingress of dirt Split/Perished. (5.3.4 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor holed and corroded within 12" of suspension mounting. (5.3.6 (a) (i)) | 1 |
| Offside Front Power steering component leaking (2.1.5 (a)) | 1 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Power steering component insecure rubber mount (2.1.5 (d) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced centre/rear section of sill (7.1.1 (a) (i)) | 1 |
| Offside Steering rack insecure movement at mounting bracket to body (2.1.3 (a) (i)) | 1 |
| Front Bumper damaged and likely to cause injury when grazed or contacted both sides (6.1.4 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Prop shaft joint constant velocity boot no longer prevents the ingress of dirt Insecure (6.1.7 (g) (ii)) | 1 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| Rear Brake pipe connection leaking on a hydraulic braking system both rears from brake cylinder to the flexi pipe (1.1.11 (b) (ii)) | 1 |
| Rear Brake drum contaminated brake fluid leaking on both rears (1.1.14 (b)) | 1 |
| Boot lid cannot be secured in the closed position fold away roof lid (6.2.1 (e)) | 1 |
| Nearside Front Floor excessively deteriorated next to jacking point (6.2.4 (a) (i)) | 1 |
| Offside Front Floor excessively deteriorated next to jacking point (6.2.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength next to rear arm mounting point (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength next to rear arm mounting point (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near tie bar mounting point (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near front mounting point (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Front Engine mounting damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
| Offside Front Engine mounting damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
| Offside Front Power steering component leaking From power steering rack (2.1.5 (a)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill and outer sill holed (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor holed (7.1.1 (a) (i)) | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt Boot split. (6.1.7 (g) (ii)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill rotted through. (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn Rear wishbone bush (5.3.4 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
| Fuel cap/sealing device sealing washer torn |7.2.4c| | 1 |
| Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
| Power steering component|s| leaking |2.3.3b| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Road wheel fixing missing ALL FOUR WHEELS (5.2.1 (a) (i)) | 1 |
| Offside Rear Exhaust silencer insecure MOUNT BROKEN (8.1.1 (b) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL AND INNER WHEEL ARCH HOLED (6.1.1 (c) (i)) | 1 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Front Direction indicator not working |1.4.A.2c| | 1 |
| Fuel hose leaking |7.2.3| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill panel |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill panel |6.1.B.2| | 1 |
| Rear fog lamp switch missing (4.5.3 (a)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired floor,inner sill chassis box section holed and rotten from front to rear wheel (6.2.2 (d) (ii)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired box section ,floor and inner sill holed and rotten (6.2.2 (d) (ii)) | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Nearside Front Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
| Offside Front Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
| Nearside Outer Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired seal |6.2.2 |d| |ii|| | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired |6.2.2 |d| |ii|| | 1 |
| Offside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting |6.2.2 |d| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot |6.2.2 |d| |i|| | 1 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Mechanical brake component has restricted free movement | 1 |
| Offside Rear Suspension arm ball joint excessively worn lower arm (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear brake application uneven | 1 |
| Nearside Front Headlamp not working on dipped beam high beam on instead (4.1.1 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on main beam dip beam on instead (4.1.1 (a) (ii)) | 1 |
| Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength trailing arm body mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength trailing arm body mount (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak rear silencer (8.2.1.1 (b)) | 1 |
| Offside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (two places) (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt split (6.1.7 (g) (ii)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corrpded (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill corroded (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill as marked (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch to sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch to sill (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Hazard warning switch inoperative (4.4.2 (a) (ii)) | 1 |
| All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Rear fog lamp does not emit a steady red light shows white (4.5.4 (a)) | 1 |
| Offside Front Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Central Rear Brake pipe likely to become detached or damaged pipe marked with chalk (1.1.11 (d) (ii)) | 1 |
| Nearside Front Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Brake master cylinder leaking (1.1.10 (b) (ii)) | 1 |
| Nearside Front Floor excessively deteriorated sill (6.2.4 (a) (i)) | 1 |
| Offside Floor excessively deteriorated sill corroded middle and rear (6.2.4 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded (7.1.1 (a) (i)) | 1 |
| Main beam tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Speedometer cannot be illuminated (7.8 (c) (ii)) | 1 |
| Offside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front floors (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wing (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch (5.3.6 (a) (i)) | 1 |
| Brake performance unable to be tested (1.2.1 (g)) | 1 |
| Offside Rear Body component corroded and likely to cause injury bumper side cap (6.2.1 (a) (i)) | 1 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Nearside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/wheel arch (5.3.6 (a) (i)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected showing white light (4.5.1 (b) (ii)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced under floor mounting badly corroded (7.1.1 (a) (i)) | 1 |
| Front Bumper likely to become detached (6.1.4 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner arch (6.1.1 (c) (i)) | 1 |
| Rear Floor excessively deteriorated (6.2.4 (a) (i)) | 1 |
| Fuel hose leaking excessively or a risk of fire Fuel filter pipe (6.1.3 (b) (ii)) | 1 |
| Rear Bumper likely to become detached (6.1.4 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner arch (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch/ bumper mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch /bumper mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt fell apart come un stuck (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area (5.3.6 (a) (i)) | 1 |
| Power steering component leaking stearing rack (2.1.5 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill holed by corrosion (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill area (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan (5.3.6 (a) (i)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected Both battery terminals (4.11 (a) (ii)) | 1 |
| Boot lid cannot be secured in the closed position (6.2.1 (e)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Door sill corroded within 30cm of seat belt mounting point. (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Rear Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Floor excessively deteriorated boot floor corroded (6.2.4 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Oil leaking excessively from transmission (8.4.1 (a) (i)) | 1 |
| Stop lamp(s) remains on when the brakes are released (4.3.2 (a) (iii)) | 1 |
| Emissions not tested due to readings locking out machine (8.2.1.2 (d)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced door step area (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch area (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill edge (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch edge (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor (5.3.6 (a) (i)) | 1 |
| Rear Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Nearside Front Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor (6.1.1 (c) (i)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced roof (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner door shut (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner door shut (6.1.1 (c) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer rear arches (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch in upper mounting of shock absorber prescribed area (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed due to leak in rear silencer failed lambda test (8.2.1.2 (d)) | 1 |