| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 44 |
| Brakes imbalanced across an axle | 35 |
| Headlamp aim out of alignment | 30 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 19 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 15 |
| Windscreen washer not working | 13 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 11 |
| Brake pipe excessively corroded | 10 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 9 |
| Parking brake lever has no reserve travel |3.1.6b| | 9 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 9 |
| Emissions not tested (8.2.1.2 (d)) | 8 |
| Registration plate lamp issues | 8 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 7 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 7 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 7 |
| Horn not working |1.6.2a| | 7 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 6 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 6 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 6 |
| Power steering component|s| leaking |2.3.3b| | 5 |
| Rear parking brake recording little or no effort | 5 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 5 |
| Horn not working (7.7 (a)) | 5 |
| Rear fog lamp missing |1.3.2a| | 5 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 4 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Registration plate issues | 4 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 4 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 4 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 4 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 4 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 3 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 3 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 3 |
| Power steering component leaking (2.1.5 (a)) | 3 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 3 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 3 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
| Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 3 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 3 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Rear fog lamp switch missing (4.5.3 (a)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 3 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 2 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 2 |
| Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 2 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill area (5.3.6 (a) (i)) | 2 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 2 |
| Rear Rear fog lamp missing |1.3.2a| | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Rear brake binding | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 2 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 2 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Rear Hydraulic brake cylinder leaking and braking performance affected (1.1.16 (b) (ii)) | 2 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 2 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Rear Exhaust system not adequately supported |7.1.1| | 2 |
| Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 2 |
| Front passenger door cannot be opened from outside the vehicle inside as well |6.2.3 |a|| | 2 |
| Front brake disc in such a condition that it is seriously weakened | 2 |
| Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 2 |
| Offside Rear Parking brake inoperative on one side |1.4.1 |a|| | 2 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 2 |
| Rear fog lamp switch missing |1.3.1a| | 2 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 2 |
| Nearside Front Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 2 |
| Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 2 |
| Rear fog lamp tell tale missing |1.3.1b| | 2 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Rear Rear fog lamp missing |1.3.2a| | 2 |
| Front brake application uneven | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch (7.1.1 (a) (i)) | 2 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Nearside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 2 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Rear Exhaust system insecure (6.1.2 (a)) | 2 |
| Nearside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 1 |
| Power steering component leaking steering rack (2.1.5 (a)) | 1 |
| Offside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Offside Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Nearside Front Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Offside Rear Brake drum contaminated (1.1.14 (b)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Rear Exhaust system insecure mountings broken (6.1.2 (a)) | 1 |
| Offside Headlamp not working on dipped beam (1.7.5a) | 1 |
| Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a) | 1 |
| Offside Rear fog lamp not working (1.3.2b) | 1 |
| Parking brake lever has no reserve travel (3.1.6b) | 1 |
| Offside Front Lower Suspension arm has excessive play in a pin/bush (2.4.G.2) | 1 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Nearside Steering rack gaiter split (2.2.D.2d) | 1 |
| Offside front brake binding (3.7.B.1) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Horn not working (1.6.2a) | 1 |
| Offside Stop lamp not working (1.2.1b) | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Bumper damaged and likely to cause injury when grazed or contacted repair tape used (6.1.4 (a) (i)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/wheel arch lower (6.1.1 (c) (i)) | 1 |
| Nearside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill at front (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill at rear (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Suspension arm locating pin locking device missing bottom ball joint split pin missing |2.4.G.3b| | 1 |
| Power steering component|s| leaking from a failed seal |2.3.3b| | 1 |
| Nearside Rear Macpherson strut has excessive movement at the upper attachment |2.5.A.1c| | 1 |
| Offside Front All position lamps not in good working order |function impaired| |1.1.A.2a| | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill rear section (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill rear section (7.1.1 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill rear section (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill rear section (5.3.6 (a) (i)) | 1 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill section tying inner to outer (5.3.6 (a) (i)) | 1 |
| Rear Exhaust system not adequately supported support rubbers fractured |7.1.1| | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Service brake is causing the vehicle to swerve to the nearside |3.7.C.2| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt split (2.1.3 (g) (ii)) | 1 |
| Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Front Exhaust has a major leak of exhaust gases Flange (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 2 areas marked with chalk ( inner wheel arch ) (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases box (6.1.2 (a)) | 1 |
| Nearside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 1 |
| Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
| Nearside Front Upper Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases backbox (6.1.2 (a)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Engine mounting damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury wheel arch sharp edge (6.2.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill excessively corroded within 30cm of seatbelt mounting and trailing arm mounting (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/floor excessively corroded within 30cm of seatbelt mounting and trailing arm mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Power steering component leaking steering rack/pipe (2.1.5 (a)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Rear Service brake imbalanced across an axle (1.2.1 (b) (i)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt Large retaining clip slightly insecure, allowing grease to be released (6.1.7 (g) (ii)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Hydraulic brake cylinder leaking hydraulic fluid n/s front brake caliper seal leaking (1.1.16 (b) (i)) | 1 |
| Central Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt insecure (2.1.3 (g) (ii)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SILL (7.1.1 (a) (i)) | 1 |
| Offside Front Windscreen wiper not working (3.4 (a)) | 1 |
| Nearside Front Brake valve leaking (1.1.7 (a) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced sill (6.1.1 (d) (i)) | 1 |
| Nearside Rear Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced sill (6.1.1 (d) (i)) | 1 |
| Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Rear fog lamp does not emit a steady red light wrong colour (4.5.4 (a)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn front (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn rear (5.3.4 (a) (i)) | 1 |
| Emissions not tested due to excess blue smoke covering workshop area (8.2.1.2 (d)) | 1 |
| Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded along its length and less than 30cm to seatbelt and seat mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill corroded (5.3.6 (a) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Steering locking device insecure |2.2.C.1g| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength rear sill (5.3.6 (a) (i)) | 1 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Power steering pipe/hose leaking |2.1.5 |a|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill area (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis outrigger holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill area (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced middle floor to sill area (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill to floor area (5.3.6 (a) (i)) | 1 |
| Exhaust system insecure rear exhaust hanger area holed boot floor (6.1.2 (a)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt boot insecure (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak backbox (8.2.1.1 (b)) | 1 |
| Emissions not tested full emissions test not carried out, exhaust leak affecting readings (8.2.1.2 (d)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Rear lower wheel arch and body corroded / holed behind rear bumper (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Rear lower wheel arch and body corroded / holed behind rear bumper (6.1.1 (c) (i)) | 1 |
| Rear fog lamp does not emit a steady red light lost colour (4.5.4 (a)) | 1 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Power steering fluid reservoir empty (2.1.5 (b) (ii)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced offside front flooring (6.1.1 (c) (i)) | 1 |
| Exhaust emits dense blue smoke at idle (8.2.1.2 (f)) | 1 |
| Emissions not tested due to excessive smoke (8.2.1.2 (d)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced nearside rear sill section (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting and centre sill (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting n/s/f and o/s/f inner sill/floor front, centre and rears (6.2.2 (d) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL ALL ALONG (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength ARCH AND SILL BACK (5.3.6 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL BACK (5.3.6 (a) (i)) | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt split (2.1.3 (g) (ii)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt split (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill and inner wheel arch area (5.3.6 (a) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Floor excessively deteriorated sill/floor corroded and holed (6.2.4 (a) (i)) | 1 |
| Offside Front Outer Floor excessively deteriorated sill/floor corroded and holed (6.2.4 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner Sill and Wheel Arch Areas Holed Close To Suspension Mounting Point (6.2.2 (d) (i)) | 1 |
| Nearside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill marked with chalk (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill marked with chalk (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill marked with chalk (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced chassis near rear belt mount (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced central floor to sill (7.1.1 (a) (i)) | 1 |
| Emissions not tested due to condensation (8.2.1.2 (d)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Offside Front Bumper likely to become detached |6.1.4 |a| |ii|| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Offside Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Offside Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear Inner Body has a projection caused by corrosion sill corroded |6.1.C.1| | 1 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle will not open from outside |6.2.B.1b| | 1 |
| Nearside Front Obligatory mirror seriously deteriorated, affecting the rear view |8.1.2a| | 1 |
| engine mounting deteriorated resulting in excessive movement |6.1.D.1a| | 1 |
| Steering column attachment defective (2.2.2 (d) (i)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Rear Bumper damaged and likely to cause injury when grazed or contacted BOTH corners. (6.1.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced centre outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner & outer sills (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner & outer sills (7.1.1 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer sills (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer sills (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced seat belt anchor point excessively corroded inner wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Lower Vehicle structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt retracting mechanism defective Not taking out all slack (7.1.2 (e)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced centre floor to sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced to centre floor to sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Rear fog lamp missing |1.3.2a| | 1 |
| Offside Front Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Rear fog lamp tell-tale missing (4.9.1 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill end/wheel arch |2.4.A.3| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Power steering ram|s| leaking from a failed joint |2.3.3b| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| front brakes release unevenly |3.7.B.4| | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Exhaust emissions likely to be affected by an exhaust leak rear silencer leaking (8.2.1.1 (b)) | 1 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Boot floor (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor pan (6.1.1 (c) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor pan (7.1.1 (a) (i)) | 1 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside front brake juddering severely |3.7.A.2b| | 1 |
| Offside front brake juddering severely |3.7.A.2b| | 1 |
| Hazard warning switch missing |1.4.B.1d| | 1 |
| Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front brake caliper has restricted free movement |3.5.1k| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Service brake juddering severely |3.7.C.2| | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Offside Front Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Nearside Rear fog lamp does not emit a steady red light Showing white light (4.5.4 (a)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower wheel arch (5.3.6 (a) (i)) | 1 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 1 |
| Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 1 |
| Offside Front Position lamp not working |4.2.1 |a| |ii|| | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded and holed |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded and holed |7.1.1 |a| |i|| | 1 |
| Rear fog lamp switch faulty |1.3.1a| | 1 |
| Brake fluid contaminated (1.8 (a)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Offside Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| rear brakes release unevenly |3.7.B.4| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Offside Front Power steering pipe|s| or hose|s| leaking from a joint pump areas |2.3.3b| | 1 |
| Offside Power steering component|s| leaking from a failed seal |2.3.3b| | 1 |
| Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Front Lower engine mounting deteriorated resulting in excessive movement gearbox stable worn |6.1.D.1a| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced B pillar by striker plate (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced B pillar by striker plate (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill, needs new complete sill (5.3.6 (a) (i)) | 1 |
| Rear Rear fog lamp does not emit a steady red light replaced bulb (4.5.4 (a)) | 1 |
| Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Offside Rear fog lamp lens defective such that emitted light is adversely affected |4.5.1 |b| |ii|| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis Outrigger |6.1.1 |c| |i|| | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill |6.1.1 |c| |i|| | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill |6.1.1 |c| |i|| | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill/Chassis Area |6.1.1 |c| |i|| | 1 |
| Power steering component leaking Rack (2.1.5 (a)) | 1 |
| Brake hose excessively deteriorated | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Sill/Floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Sill/Floor (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired Chassis Outrigger (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor Area (6.2.2 (d) (i)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Rear Position lamp adversely affected by the operation of another lamp All (4.2.3 (c)) | 1 |
| Offside Rear Rear fog lamp adversely affected by the operation of another lamp (4.5.4 (b)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor Area (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor/Sill Area (5.3.6 (a) (i)) | 1 |
| Offside Front coil spring broken |2.4.C.1a| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced cemtre sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt grease leaking from dust cover (5.3.4 (b) (ii)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Front Direction indicator not working |1.4.A.2c| | 1 |
| Offside Front Rear fog lamp not working |1.3.2b| | 1 |
| Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Steering box leaking to the extent that oil is dripping (2.1.1 (e) (ii)) | 1 |
| Floor excessively deteriorated Boot Floor (6.2.4 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Body component corroded and likely to cause injury rear bumper (6.2.1 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Front Outer Prop shaft joint constant velocity boot no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Front Fuel system component leaking (6.1.3 (b) (i)) | 1 |
| Nearside Inner Front Brake valve leaking |3.6.A.1| | 1 |
| Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive co 0.39 |7.3.D.4| | 1 |
| Exhaust engine idle speed too high |7.3.D.1| | 1 |
| Central Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill/floor has corroded hole (7.1.1 (a) (i)) | 1 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Rear Rear fog lamp lens defective such that emitted light is adversely affected showing white (4.5.1 (b) (ii)) | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii)) | 1 |
| Rear Emissions not tested reading too high may damage equipment (8.2.1.2 (d)) | 1 |
| Vehicle structure is fractured and structural rigidity is significantly reduced n/s & o/s inner sills corroded (6.1.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting both inner side sills (6.2.2 (d) (i)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Stop lamp(s) not working all rear (4.3.1 (a) (ii)) | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Front Direction indicator missing (4.4.1 (a) (ii)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced offside rear chassis holed two places (6.1.1 (c) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced spare wheel well holed (6.1.1 (c) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear chassis both sides at lower rear bumper mounts (6.1.1 (c) (i)) | 1 |
| Suspension arm corroded and seriously weakened offside front wishbone mount area holed (5.3.3 (b) (i)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sills both side (6.1.1 (c) (i)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre outersill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner (5.3.6 (a) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Both inner sills excessively corroded. (6.1.1 (c) (i)) | 1 |
| Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Suspension arm mounting point area excessively corroded. (5.3.6 (a) (ii)) | 1 |
| Rear Exhaust system insecure Rear section insecure and touching rear axle. (6.1.2 (a)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Wheelarch corroded at bottom in prescribed area (chassis) (6.1.1 (c) (i)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill heavily corroded (5.3.6 (a) (i)) | 1 |