Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 32 |
Brakes imbalanced across an axle | 32 |
Brake pipe excessively corroded | 20 |
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 15 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 13 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 13 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 12 |
Windscreen washer not working | 10 |
Headlamp aim out of alignment | 8 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 8 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 7 |
Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 6 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 6 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 5 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 5 |
Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 5 |
Horn not working (7.7 (a)) | 4 |
Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 4 |
Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 4 |
Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 4 |
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 4 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 4 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 3 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 3 |
Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
Mechanical brake component has restricted free movement | 3 |
Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
Emissions not tested (8.2.1.2 (d)) | 3 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 2 |
Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 2 |
Brake lever has insufficient reserve travel (1.1.2 (a)) | 2 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 2 |
Nearside Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 2 |
Stop lamp(s) remains on when the brakes are released (4.3.2 (a) (iii)) | 2 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 2 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
Power steering component leaking (2.1.5 (a)) | 2 |
Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
Offside Rear Service brake lagging in operation (1.2.1 (d)) | 2 |
Brake pedal has insufficient reserve travel (1.1.2 (a)) | 2 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
Exhaust emits dense blue smoke at idle (8.2.1.2 (f)) | 2 |
Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
Offside Steering rack gaiter split |2.2.D.2d| | 2 |
Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 2 |
Power steering component leaking RACK (2.1.5 (a)) | 2 |
Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 2 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 2 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
Nearside Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 2 |
Rear Exhaust system insecure (6.1.2 (a)) | 2 |
Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 2 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Registration plate lamp issues | 2 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
Steering rack insecure |2.2.B.1a| | 2 |
Rear Exhaust system not adequately supported (7.1.1) | 2 |
Rear Rear fog lamp not working (1.3.2b) | 2 |
Main beam tell-tale missing (4.9.1 (a) (ii)) | 2 |
Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
Front brake disc in such a condition that it is seriously weakened | 2 |
Registration plate issues | 2 |
Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
Centre Exhaust has a major leak of exhaust gases (7.1.2) | 2 |
Rear fog lamp not working (1.3.2b) | 2 |
Parking brake lever has no reserve travel (3.1.6b) | 2 |
All direction indicators not working (4.4.1 (a) (ii)) | 1 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor and sill (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced around door catch (7.1.1 (a) (i)) | 1 |
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
Fuel pipe leaking Fuel filter hose in engine bay (6.1.3 (b) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Back quarter (5.3.6 (a) (i)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Spare wheel well floor (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner front wheel arch (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner front wheel arch (5.3.6 (a) (i)) | 1 |
Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Emissions not tested due to exhaust leak (8.2.1.2 (d)) | 1 |
Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill corroded through with in 30cm of a seat belt mount marked with yellow chalk (6.1.1 (c) (i)) | 1 |
Power steering inoperative and steering adversely affected (2.1.5 (c) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 14 panel (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 14 panel (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Parking brake inoperative on one side x2 (1.4.1 (a)) | 1 |
Nearside Front Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Offside Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
Nearside Rear Brake drum contaminated (1.1.14 (b)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill area (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wing at sill end (5.3.6 (a) (i)) | 1 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Offside Ball joint has excessive play |2.2.B.1f| | 1 |
Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
Nearside front brake binding |3.7.B.1| | 1 |
Rear Gas suspension unit leaking |2.4.D.2| | 1 |
Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
Nearside Rear Parking brake inoperative on one side Nearside rear not operating/working as intended (1.4.1 (a)) | 1 |
Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner seal area (6.2.2 (d) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced central sill (7.1.1 (a) (i)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced central sill (7.1.1 (a) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced central sill (7.1.1 (a) (i)) | 1 |
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner seal (6.1.1 (c) (i)) | 1 |
Offside Rear Vehicle structure modified such that structural rigidity is significantly reduced inner seal (6.1.1 (d) (i)) | 1 |
Rear fog lamp switch missing (4.5.3 (a)) | 1 |
Nearside Front Shock absorbers has a serious fluid leak | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner lower wheel arch to sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired inner sill area (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area (5.3.6 (a) (i)) | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Front Engine mounting bracket damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
Power steering component leaking At steering rack (2.1.5 (a)) | 1 |
Offside Rear Valve stem seriously damaged (5.2.3 (j)) | 1 |
Nearside Rear Suspension arm attachment bracket/mounting damaged and seriously weakened trailing arm mount (5.3.3 (b) (i)) | 1 |
Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower arch (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear sill (5.3.6 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor/sill (7.1.1 (a) (i)) | 1 |
Seat belt anchorage likely to become detached in the event of a collision (7.1.1 (a) (ii)) | 1 |
Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor/spare wheel carrier (7.1.1 (a) (i)) | 1 |
Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both inner sills (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sil (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Spare wheel well (6.1.1 (c) (i)) | 1 |
Drivers door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
Obligatory mirror missing Both (3.3 (a)) | 1 |
Emissions not tested exhaust blow (8.2.1.2 (d)) | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Stop lamp(s) missing (4.3.1 (a) (ii)) | 1 |
Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Nearside Stop lamp not working |1.2.1b| | 1 |
Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Front brake application uneven | 1 |
Front Fuel pipe union leaking INJECTOR AREA (6.1.3 (b) (i)) | 1 |
Power steering inoperative (2.1.5 (c) (i)) | 1 |
Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Emissions not tested excessive exhaust blow (8.2.1.2 (d)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner , outer and end of sill (5.3.6 (a) (i)) | 1 |
Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
Offside Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
Rear fog lamp tell-tale missing (4.9.1 (a) (ii)) | 1 |
Rear Exhaust has a major leak of exhaust gases exhaust back box (6.1.2 (a)) | 1 |
Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
Offside Rear Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
Nearside Front Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
Nearside Front Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i)) | 1 |
Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
Offside Rear Rear fog lamp lens defective such that emitted light is adversely affected showing white light (4.5.1 (b) (ii)) | 1 |
Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
Offside Front Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
Exhaust system insecure rear mounting broken (6.1.2 (a)) | 1 |
Power steering pipe/hose leaking pump area (2.1.5 (a)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear tailgate (5.3.6 (a) (i)) | 1 |
Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front and rear (5.3.6 (a) (i)) | 1 |
Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front and rear (5.3.6 (a) (i)) | 1 |
Nearside Rear Body panel corroded and likely to cause injury Wheel arch (6.2.1 (a) (i)) | 1 |
Offside Rear Body panel corroded and likely to cause injury Wheel arch (6.2.1 (a) (i)) | 1 |
Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Nearside Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
Offside Power steering component leaking steering rack (2.1.5 (a)) | 1 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Headlamp aim not tested (4.1.2 (b)) | 1 |
Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
Offside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
Nearside Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
Brake master cylinder leaking (1.1.10 (b) (ii)) | 1 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii)) | 1 |
Offside Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wheel Arch (6.1.1 (c) (i)) | 1 |
Nearside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
Offside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
Offside Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
Offside Front Bumper likely to become detached (6.1.4 (a) (ii)) | 1 |
Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
Nearside Rear Brake lining(s) contaminated (1.1.13 (b)) | 1 |
Offside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
Offside Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Offside Front Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
Offside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
Horn not working |1.6.2a| | 1 |
Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
Power steering pipe|s| or hose|s| leaking steering rack |2.3.3b| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
Nearside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill marked with chalk (7.1.1 (a) (i)) | 1 |
Offside Front Prop shaft joint constant velocity boot no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
Rear brake binding | 1 |
Nearside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Nearside Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Offside Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Cross member behind rear bumper (6.1.1 (c) (i)) | 1 |
Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Spare wheel carrier (6.1.1 (c) (i)) | 1 |
Rear Exhaust system insecure Exhaust rubber perished (6.1.2 (a)) | 1 |
Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
Offside Front Lower Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
Emissions not tested off scale (8.2.1.2 (d)) | 1 |
Offside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 1 |
Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Rear Rear fog lamp not working |1.3.2b| | 1 |
Nearside Side repeater not working |1.4.A.2c| | 1 |
Service brake: efficiency below requirements |3.7.B.7| | 1 |
Rear fog lamp tell tale not working |1.3.1b| | 1 |
Offside Rear fog lamp not working |1.3.2b| | 1 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Power steering component|s| leaking |2.3.3b| | 1 |
Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Rear parking brake recording little or no effort | 1 |
Parking brake: efficiency below requirements |3.7.B.7| | 1 |
Offside Stop lamp not working |1.2.1b| | 1 |
Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
Offside Side repeater not working |1.4.A.2c| | 1 |
Steering wheel retaining device missing |2.1.6| | 1 |
Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Drivers door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
Offside Front Drivers door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
Offside Front Track rod end modification unsafe locking device ineffective (2.1.3 (f) (i)) | 1 |
Nearside Front Windscreen wiper blade missing (3.4 (b) (ii)) | 1 |
Offside Front Windscreen wiper blade missing (3.4 (b) (ii)) | 1 |
Nearside Front Lower Fluid leak harmful to the environment or a risk to other road users radiator leaking (8.4.1 (a) (i)) | 1 |
Offside Rear Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 1 |
Nearside Front Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
Nearside Front Suspension arm locating pin insecure |2.4.G.3a| | 1 |
Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor. (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner flitch (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill several places (5.3.6 (a) (i)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both rear undersills (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outersill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outersill (5.3.6 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill behind passenger door (7.1.1 (a) (i)) | 1 |
Power steering component leaking steering rack (2.1.5 (a)) | 1 |
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
Nearside Rear Lower Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
Rear Rear fog lamp does not emit a steady red light showing more white than red (4.5.4 (a)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL (7.1.1 (a) (i)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL (7.1.1 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER ARCH (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength INNER ARCH (5.3.6 (a) (i)) | 1 |
Offside Rear Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
Offside Rear Parking brake mechanism/associated mounting prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
Fuel system component leaking number 1 injector leaking (6.1.3 (b) (i)) | 1 |
Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
Offside Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
Windscreen wiper not working nearside and offside (3.4 (a)) | 1 |
Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in inner wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced in inner wheel arch (7.1.1 (a) (i)) | 1 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Offside Front Direction indicator not working (1.4.A.2c) | 1 |
Offside Front Front constant velocity joint gaiter split (2.5.C.1a) | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
Offside Rear Shock absorber has negligible damping effect (2.7.5) | 1 |
Rear Parking brake lever has no reserve travel (3.1.6b) | 1 |
Front Front constant velocity joint gaiter split (2.5.C.1a) | 1 |
Rear Rear fog lamp missing (1.3.2a) | 1 |
Nearside Stop lamp not working (1.2.1b) | 1 |
Nearside Rear position lamp(s) not working (1.1.A.3b) | 1 |
Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
Parking brake: efficiency below requirements (3.7.B.7) | 1 |
Rear Exhaust tailpipe not capable of allowing the emission probe to be inserted (7.3.B.1) | 1 |
Offside Front Suspension arm locating pin locking device missing lower ball joint (2.4.G.3b) | 1 |
Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt insecure (6.1.7 (g) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area (7.1.1 (a) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Rear Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |