| Most common failures | No# failures |
|---|
| Windscreen washer not working | 23 |
| Windscreen wiper does not clear the windscreen effectively | 16 |
| Brakes imbalanced across an axle | 16 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 11 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 11 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 10 |
| Headlamp aim out of alignment | 8 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 8 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 7 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 6 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 6 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 5 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 5 |
| Brake pipe excessively corroded | 5 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 4 |
| Rear Exhaust system insecure (6.1.2 (a)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 3 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 3 |
| Rear fog lamp not working |1.3.2b| | 3 |
| Offside Front Shock absorbers has a serious fluid leak | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 3 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 3 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 3 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 3 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 3 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 2 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Registration plate lamp issues | 2 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 2 |
| Nearside Front Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 2 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 2 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 2 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Front brake application uneven | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 2 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 2 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Rear Exhaust system not adequately supported |7.1.1| | 2 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| All direction indicators not working (4.4.1 (a) (ii)) | 2 |
| Hazard warning lamps inoperative (4.4.1 (e)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Driver`s door does not latch securely closed |6.2.B.1a| | 1 |
| Power steering fluid level below minimum |2.3.1| | 1 |
| Power steering malfunctioning |2.3.3a| | 1 |
| Power steering component|s| leaking |2.3.3b| | 1 |
| Battery insecure |1.9.1| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Front Service brake excessively fluctuating |1.2.1 |e|| | 1 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Inner Suspension component mounting prescribed area is excessively corroded sills both sides near suspension |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Rear fog lamp switch faulty |1.3.1a| | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Central outer sill holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Behind wheel floor to bumper holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Service brake excessively fluctuating Judder present. (1.2.1 (e)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Excess corrosion to holes to sill within 12" of nearside front seat belt lower anchorage. (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Excess corrosion to holes to sill within 12" of nearside front suspension. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Excess corrosion to holes to sill within 12" of nearside rear suspension. (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg at wishbone rear mount (5.3.6 (a) (i)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor and sill panel (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill and floor panel (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill and Inner panel (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor and sill panel (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ( Chalked ). (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to sill areas ( Chalked ). (7.1.1 (a) (i)) | 1 |
| Nearside Rear Shock absorbers has a serious fluid leak | 1 |
| Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ( Chalked ). (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to sill areas ( Chalked ). (7.1.1 (a) (i)) | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced cill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor/cill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner/outer, and end of cill (5.3.6 (a) (i)) | 1 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Nearside Front Steering locking device missing (2.1.3 (d)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut top fixing (5.3.6 (a) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both rear inner sills (6.1.1 (c) (i)) | 1 |
| Power steering component leaking (2.1.5 (a)) | 1 |
| Headlamp not working on dipped beam Both (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Exhaust system insecure Rear exhaust box (6.1.2 (a)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 1 |
| front brakes release unevenly |3.7.B.4| | 1 |
| Offside Rear Lower Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Rear Lower Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Lower Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Front Seat belt pretensioner deployed (7.1.4 (a)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Emissions not tested too much smoke (8.2.1.2 (d)) | 1 |
| Exhaust has a major leak of exhaust gases front pipe holed. (6.1.2 (a)) | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Brake fluid warning lamp illuminated |3.6.G.2| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded outersill |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outersill |5.2.6| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light white (4.5.4 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Fuel system component leaking Near fuel filter (6.1.3 (b) (i)) | 1 |
| Fuel system component leaking by fuel filter (6.1.3 (b) (i)) | 1 |
| Nearside Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn front (5.3.4 (a) (i)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Position lamp not working All (4.2.1 (a) (ii)) | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected outer sill not fully welded (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected outer sill not fully welded (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected outer sill not fully welded (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected outer sill not fully welded (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected inner wheel arch not fully welded (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected inner wheel arch not fully welded (5.3.6 (a) (ii)) | 1 |
| Offside Rear Passengers seat backrest cannot be secured in the upright position. (6.2.6 (a) (i)) | 1 |
| Boot lid cannot be secured in the closed position (6.2.1 (e)) | 1 |
| Emissions not tested due to engine overheating (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail by back box (5.3.6 (a) (i)) | 1 |
| Nearside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front and mid sill areas (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill areas (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch and FUEL TANK AREA (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan area (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan area (7.1.1 (a) (i)) | 1 |
| Offside Inner Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill areas (7.1.1 (a) (i)) | 1 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill / inner sill / floor (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill / inner sill / floor (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting bumper mounts / boot area (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting bumper mounts / boot area (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Emissions not tested due to exhaust condition (8.2.1.2 (d)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak rear silencer (8.2.1.1 (b)) | 1 |
| Exhaust system insecure rear silencer (6.1.2 (a)) | 1 |
| Exhaust has a major leak of exhaust gases rear silencer (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced a post (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL (6.2.2 (d) (i)) | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL (6.2.2 (d) (i)) | 1 |
| Front Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Power steering component leaking rack (2.1.5 (a)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to Sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to Sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower suspension arm corroded (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill lip/ floor (5.3.6 (a) (i)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Front Service brake imbalanced across an axle (1.2.1 (b) (i)) | 1 |
| Hydraulic fluid leaking excessively (8.4.1 (a) (i)) | 1 |
| Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked with chalk (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Rear fog lamp tell-tale missing (4.9.1 (a) (ii)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill x2 (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Nearside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Floor excessively deteriorated Floor pan corroded (6.2.4 (a) (i)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Offside Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Offside Rear fog lamp not working |1.3.2b| | 1 |
| Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Wheel arch (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Door sill x2 (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Wheel arch (5.3.6 (a) (ii)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Door sill x2 (7.1.1 (a) (i)) | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Brake lever has insufficient reserve travel Hand brake. (1.1.2 (a)) | 1 |
| Nearside Rear Body insecure to the extent that stability is seriously impaired boot floor (6.2.2 (a) (ii)) | 1 |
| Offside Rear Body insecure to the extent that stability is seriously impaired boot floor above back box exhaust (6.2.2 (a) (ii)) | 1 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Drivers seat fore and aft adjustment mechanism not functioning as intended. (6.2.5 (b) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill going on to driver side floor (6.1.1 (c) (i)) | 1 |
| Horn not working |1.6.2a| | 1 |
| Offside Inner Power steering component|s| leaking |2.3.3b| | 1 |
| Offside Inner Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases Exhaust box (6.1.2 (a)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases BOX (6.1.2 (a)) | 1 |
| Offside Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back (5.3.6 (a) (i)) | 1 |
| Exhaust system insecure rear mountings (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Power steering component leaking (2.1.5 (a)) | 1 |
| Offside Steering rack has excessive free play detected at the steering wheel (steering rack fitted) (2.3 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point /floor (6.2.2 (d) (i)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill / floor (7.1.1 (a) (i)) | 1 |