| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 28 |
| Brake pipe excessively corroded | 27 |
| Brakes imbalanced across an axle | 24 |
| Windscreen washer not working | 16 |
| Headlamp aim out of alignment | 14 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 12 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 11 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 11 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 11 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 9 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 8 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 7 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 7 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 6 |
| Horn not working (7.7 (a)) | 6 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 6 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 5 |
| Registration plate issues | 5 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 5 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 5 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 5 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 4 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
| Rear fog lamp tell tale not working |1.3.1b| | 4 |
| Offside Rear fog lamp not working |1.3.2b| | 4 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 4 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Front Shock absorbers has a serious fluid leak | 3 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 3 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Rear fog lamp not working |1.3.2b| | 3 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 3 |
| Nearside Rear Shock absorbers has a serious fluid leak | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 3 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 3 |
| Rear Rear fog lamp not working |1.3.2b| | 3 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 3 |
| Rear Exhaust system insecure (6.1.2 (a)) | 3 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 2 |
| Hydraulic fluid leaking excessively steering rack (8.4.1 (a) (i)) | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Offside Rear Seat belt buckle not functioning as intended (7.1.2 (d)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Main beam tell-tale not working (4.9.1 (a) (ii)) | 2 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 2 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 2 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Rear fog lamp missing |1.3.2a| | 2 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 2 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Rear fog lamp tell-tale missing (4.9.1 (a) (ii)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 2 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Rear fog lamp switch missing |1.3.1a| | 2 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 2 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 2 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Passenger`s seat insecure |6.2.A.1| | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Offside Rear Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Nearside Front Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Exhaust silencer insecure (8.1.1 (b) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak frontpipe joint (8.2.1.1 (b)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nearside sill (7.1.1 (a) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn trailing arm (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/wheelarch (5.3.6 (a) (i)) | 1 |
| Nearside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (several places) (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (several places) (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt split (2.1.3 (g) (ii)) | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Rear Service brake grabbing severely (1.2.1 (c)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Steering locking device ineffective track rod end no split pin (2.1.3 (d)) | 1 |
| Nearside Front Steering locking device ineffective not a proper locking device nut (2.1.3 (d)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced center inner sill (6.1.1 (c) (i)) | 1 |
| Fuel pipe leaking fuel filler neck (6.1.3 (b) (i)) | 1 |
| Offside Obligatory mirror insecure (3.3 (b) (ii)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill x3 (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor/ jacking point (6.2.2 (d) (i)) | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
| Centre Rear fog lamp not working |1.3.2b| | 1 |
| Rear fog lamp not working Tell Tell, plus lens tape (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer wing holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength full sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength full sill (5.3.6 (a) (i)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Brake fluid not visible (1.1.10 (d) (iii)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced holes in A pillar (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength base of sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength base of sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced hole in chassis reinforcing rail (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced hole in chassis reinforcing rail (7.1.1 (a) (i)) | 1 |
| Nearside Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor/rear panel (6.2.2 (d) (i)) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting out rigger (6.2.2 (d) (i)) | 1 |
| Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting floor panel (6.2.2 (d) (i)) | 1 |
| Exhaust catalytic converter missing where one was fitted as standard Cat warning lamp on dash (8.2.1.1 (a)) | 1 |
| Nearside Rear Seat belt anchorage likely to become detached in the event of a collision prescribed are excessively corroded (7.1.1 (a) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan (7.1.1 (a) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill area (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Centre/ front (outer sill area) (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Floor area (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill area (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both sills (7.1.1 (a) (i)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch/end of sill panel (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel (7.1.1 (a) (i)) | 1 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Emissions unable to be completed due to exhaust blow at rear (8.2.1.2 (d)) | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Rear fog lamp switch inoperative |4.5.3 |a| |ii|| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Exhaust has a major leak of exhaust gases manifold |7.1.2| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn front (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at wishbone mounting area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at wishbone mounting area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill / floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor underneath (6.2.2 (d) (i)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users COOLANT (8.4.1 (a) (i)) | 1 |
| Emissions unable to be completed EXHAUST BLOWING (8.2.1.2 (d)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering Front and rear sill area have holes and corrosion (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Central Rear Stop lamp(s) with a multiple light source more than 1/2 not functioning (4.3.1 (a) (ii)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength os floor to sill front to rear (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie (5.3.6 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x member (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases box (6.1.2 (a)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Central Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Seat belt affected by an insecure seat fixing n/s/f seat not secure to floor (5.2.1b) | 1 |
| Rear fog lamp missing (1.3.2a) | 1 |
| Power steering component(s) leaking around steering box (2.3.3b) | 1 |
| Nearside front brake binding (3.7.B.1) | 1 |
| Nearside Stop lamp not working (1.2.1b) | 1 |
| Nearside Outer Front constant velocity joint gaiter split (2.5.C.1a) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
| Nearside Front Lower Steering locking device missing (2.1.3 (d)) | 1 |
| Battery insecure (1.9.1) | 1 |
| Electrical wiring insecure to rear fog light (1.9.2a) | 1 |
| Nearside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a) | 1 |
| Offside Front coil spring broken (2.4.C.1a) | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded inner sill + inner arch (2.4.A.3) | 1 |
| Nearside Track rod end ball joint has excessive play (2.2.B.1f) | 1 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Body component corroded and likely to cause injury Bumper (6.2.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill to wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Other passenger door cannot be opened from outside the vehicle boot (6.2.3 (a)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced 6 holes along the whole of sill, marked with yellow chalk (6.1.1 (c) (i)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Seat belt anchorage likely to become detached in the event of a collision (7.1.1 (a) (ii)) | 1 |
| Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Rear Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Front Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Emissions unable to be completed engine shows signs of over heating (8.2.1.2 (d)) | 1 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Rear fog lamp obviously incorrectly positioned (4.5.4 (a)) | 1 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases Flange joint is blowing (6.1.2 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired floor patch is tack welded (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired Floor panel is a tack welded patch (7.1.1 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Brake fluid not visible (1.1.10 (d) (iii)) | 1 |
| Nearside Rear Hydraulic brake cylinder leaking and braking performance affected (1.1.16 (b) (ii)) | 1 |
| Emissions not tested (8.2.1.2 (d)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill x2 holes |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill end in wheel arch |2.4.A.3| | 1 |
| Rear fog lamp tell tale missing |1.3.1b| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front brake application uneven | 1 |
| Rear parking brake recording little or no effort | 1 |
| Headlamp incorrect colour |1.7.5b| | 1 |
| Exhaust emissions carbon monoxide content excessive verry high |7.3.B.1a| | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Rear Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Nearside Rear Lower Suspension arm pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear bumper mounting area (5.3.6 (a) (i)) | 1 |
| Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Body component corroded and likely to cause injury front bumper (6.2.1 (a) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced quarter (6.1.1 (c) (i)) | 1 |
| Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected Will and floor corroded (5.3.6 (a) (ii)) | 1 |
| Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Brake hose excessively deteriorated | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt Split (2.1.3 (g) (ii)) | 1 |
| Nearside Front Coil spring insecure Mounted incorrectly (5.3.1 (a) (i)) | 1 |
| Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 1 |
| Registration plate lamp issues | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Offside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Offside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner corner (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked yellow (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked yellow (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corroded as marked (5.3.6 (a) (i)) | 1 |
| Nearside Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength SILL - CENTRAL & REAR AREA - MARKED YELLOW (2 HOLES) (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill shut (5.3.6 (a) (i)) | 1 |
| Power steering ram leaking (2.1.5 (a)) | 1 |
| Offside Front Engine mounting excessively loose (6.1.8 (a) (ii)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner & outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Offside Front Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Horn sound not in accordance with requirements (7.7 (c)) | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Stop lamp not working both side |1.2.1b| | 1 |
| Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt both side |2.2.C.1c| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill back (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill back (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced in varies places (7.1.1 (a) (i)) | 1 |
| Hazard warning switch inoperative missing (4.4.2 (a) (ii)) | 1 |
| Rear fog lamp switch missing (4.5.3 (a)) | 1 |
| Rear Exhaust system insecure back box (6.1.2 (a)) | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Front Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Spare wheel well (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor area at seat mount /belt mount (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Floor excessively deteriorated corroded through (6.2.4 (a) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Full Lenght Of Outer Sill Badly Corroded (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Full Lenght Of Outer Sill Badly Corroded (6.1.1 (c) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear Of vInner Sill .. (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear Of Inner Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength trailing arm mounting point / rear of outer sils (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed Due to exhaust blow (8.2.1.2 (d)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Bumper damaged and likely to cause injury when grazed or contacted front bumper corroded, shape edges (6.1.4 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear exhaust silencer deteriorated too excess (6.1.2 (a)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill panel (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Power steering component leaking rack (2.1.5 (a)) | 1 |
| Mechanical brake component has restricted free movement | 1 |
| Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Nearside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill to floor (5.3.6 (a) (ii)) | 1 |
| Offside Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
| Brake lever has abnormal movement of levers indicating excessive wear or maladjustment (1.1.15 (f)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength flooring (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength flooring (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength FRONT (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength REAR (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed (8.2.1.2 (d)) | 1 |
| Brake fluid significantly below minimum mark |1.1.10 |d| |ii|| | 1 |
| Nearside Rear Hydraulic fluid leaking excessively wheel cylinder |8.4.1 |a| |i|| | 1 |
| Nearside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Sill area. (7.1.1 (a) (i)) | 1 |
| Nearside Front Power steering component|s| leaking |2.3.3b| | 1 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Rear Position lamp switch missing |1.1.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Service brake is causing the vehicle to swerve to the offside (1.2.1 (b) (i)) | 1 |
| Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt cv boot clip missing (6.1.7 (g) (ii)) | 1 |
| Offside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt outer (6.1.7 (g) (ii)) | 1 |