| Most common failures | No# failures |
|---|
| Brakes imbalanced across an axle | 17 |
| Windscreen wiper does not clear the windscreen effectively | 15 |
| Headlamp aim out of alignment | 13 |
| Brake pipe excessively corroded | 11 |
| Windscreen washer not working | 9 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 8 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 6 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 5 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 4 |
| Horn not working (7.7 (a)) | 4 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 4 |
| Registration plate issues | 3 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 3 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 3 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 3 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 3 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Offside Rear fog lamp missing |1.3.2a| | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Offside Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Power steering component leaking steering rack (2.1.5 (a)) | 2 |
| Offside Front Shock absorbers has a serious fluid leak | 2 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Nearside Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 2 |
| Offside Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 2 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 2 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 2 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 2 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill along the whole length (6.1.1 (c) (i)) | 2 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill along the whole length (6.1.1 (c) (i)) | 2 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill in numerous places (6.1.1 (c) (i)) | 2 |
| Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 2 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Rear parking brake recording little or no effort | 2 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 2 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 2 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Rear fog lamp switch missing |1.3.1a| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner seal |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inside the arch |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer seal |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner seal |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer seal |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer seal |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inside the arch |6.1.B.2| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Power steering pump leaking from a failed seal |2.3.3b| | 1 |
| Nearside Rear Coil spring not correctly located |2.4.C.2| | 1 |
| Nearside Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Direction indicators flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Front Direction indicator not working cleaned connection (4.4.1 (a) (ii)) | 1 |
| Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Registration plate lamp issues | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Power steering component|s| leaking around rack pinion |2.3.3b| | 1 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner seal (7.1.1 (a) (i)) | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner seal (7.1.1 (a) (i)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Rear fog lamp not working change bulb (4.5.1 (a) (ii)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Macpherson strut top bush or bearing has excessive wear or free play (5.3.4 (a) (i)) | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt split (2.1.3 (g) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Rear Exhaust system insecure Silencer rubber not holding exhaust (6.1.2 (a)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Offside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
| Offside Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 1 |
| Offside Front Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Nearside Rear Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Inner Seat belt anchorage prescribed area is inadequately repaired sill (not seam welded) (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheelarch/sill (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area is inadequately repaired sill (not fully seam welded) (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill to suspension arm mount. (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner Wing To suspension arm mount (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Axle mount. (6.2.2 (d) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor To Sill (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor To Sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component insecurely attached ball joint nut locking device missing (5.3.3 (a) (i)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Emissions not tested exhaust blow and e/m/l (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension arm attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Offside Front Suspension arm attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Offside Front Suspension arm insecurely attached chassis rotted away (5.3.3 (a) (i)) | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened sill/floor (5.3.3 (b) (i)) | 1 |
| Offside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened floor/sill (5.3.3 (b) (i)) | 1 |
| Nearside Seat belt installation has an anchorage without suitable reinforcement floor (10.1 (f)) | 1 |
| Offside Seat belt installation has an anchorage without suitable reinforcement floor (10.1 (f)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| Emissions unable to be completed (8.2.1.2 (d)) | 1 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner , outer ,wheel arch, sill (5.3.6 (a) (i)) | 1 |
| Floor excessively deteriorated boot floor (6.2.4 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill near rear tie bar mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch near tie bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sills (6.1.1 (c) (i)) | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Main beam tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak exhaust box has major leak (8.2.1.1 (b)) | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill area holed (6.1.1 (c) (i)) | 1 |
| Power steering component leaking rack area (2.1.5 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor/sill (5.3.6 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill area (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear Exhaust silencer insecure (8.1.1 (b) (i)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Drivers door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both outer sills (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt steering gaiter split (2.1.3 (g) (ii)) | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Central Rear Lower Engine mounting damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill marked with white chalk (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill marked with white chalk (7.1.1 (a) (i)) | 1 |
| Service brake imbalanced across an axle axle 2 (1.2.1 (b) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch to lower inner wing (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch to lower inner wing (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Front Macpherson strut has excessive movement in the upper support bearing assembly |2.5.B.1b| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL AREA |6.1.B.2| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL AREA |6.1.B.2| | 1 |
| Power steering component leaking Steering rack area (2.1.5 (a)) | 1 |
| Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength the spare wheel area badly corroded |5.3.6 |a| |i|| | 1 |
| Offside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering floor (6.1.1 (c) (ii)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt split (2.1.3 (g) (ii)) | 1 |