| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 33 |
| Windscreen wiper does not clear the windscreen effectively | 26 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 15 |
| Rear fog lamp switch missing (4.5.3 (a)) | 14 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 14 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 13 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 13 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 12 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 12 |
| Registration plate issues | 10 |
| Registration plate lamp issues | 10 |
| Brake pipe excessively corroded | 10 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 8 |
| Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 8 |
| Windscreen washer not working | 8 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 8 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 7 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 7 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 7 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 6 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 5 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 5 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 5 |
| Nearside Rear Shock absorbers has a serious fluid leak | 5 |
| Anti-lock braking system warning lamp indicates an ABS fault | 4 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Brakes imbalanced across an axle | 4 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 4 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 4 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 3 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Offside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 3 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 3 |
| Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 3 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Rear Shock absorbers has a serious fluid leak | 3 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 3 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 3 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 3 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 3 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 3 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 3 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Offside Rear fog lamp missing |1.3.2a| | 2 |
| Rear fog lamp switch missing |1.3.1a| | 2 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 2 |
| Offside Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 2 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 2 |
| Central Seat belt buckle not functioning as intended (7.1.2 (d)) | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 2 |
| Nearside Front Suspension arm pin or bush excessively worn Rear bush (5.3.4 (a) (i)) | 2 |
| Offside Front Suspension arm pin or bush excessively worn Rear bush (5.3.4 (a) (i)) | 2 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 2 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Offside Front Power steering pipe/hose leaking (2.1.5 (a)) | 2 |
| Offside Rear Outer Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 2 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Horn not working (7.7 (a)) | 2 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Front Bumper likely to become detached (6.1.4 (a) (ii)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Emissions unable to be completed (8.2.1.2 (d)) | 2 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Mechanical brake component has restricted free movement | 1 |
| Offside Front Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Rear fog lamp tell tale missing |1.3.1b| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Rear parking brake recording little or no effort | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc inner joint |2.5.C.1a| | 1 |
| Offside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Nearside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Driver`s airbag obviously defective |5.4.1| | 1 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint drop link |2.5.B.1a| | 1 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 1 |
| Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Brake hydraulic reservoir fluid level significantly below minimum level |1.1.10 |d| |ii|| | 1 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Brake fluid warning lamp illuminated |3.6.G.2| | 1 |
| Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 1 |
| Speedometer cannot be illuminated (7.8 (c) (ii)) | 1 |
| Offside Rear Seat belt buckle missing (7.1.2 (d)) | 1 |
| Offside Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
| Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
| Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is inadequately repaired sill - multiple (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill - multiple (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill - multiple (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill - multiple (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Headlamp levelling device inoperative Linkage missing (4.1.5 (a)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sills corroded and holed (6.1.1 (c) (i)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded and holed (6.1.1 (c) (i)) | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced full rear of car corroded and holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch area corroded and holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch area corroded and holed (6.1.1 (c) (i)) | 1 |
| Power steering component leaking (2.1.5 (a)) | 1 |
| Offside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill / inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (dorrstep insecure) (5.3.6 (a) (i)) | 1 |
| Front Position lamp not working both front (4.2.1 (a) (ii)) | 1 |
| Rear Position lamp not working both rear (4.2.1 (a) (ii)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect headlight cloudy (4.1.2 (c)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect headlight cloudy (4.1.2 (c)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Central Rear Rear wheel steering linkage deformed to the extent that steering is affected (2.1.3 (c) (ii)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt Drop link (5.3.4 (b) (ii)) | 1 |
| Windscreen wiper missing (3.4 (a)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting centre inner sill (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting centre inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Nearside Front Hydraulic brake calliper leaking from the flexi union to the calliper (1.1.16 (b) (i)) | 1 |
| Front Suspension arm pin or bush excessively worn rear bushes x2 (5.3.4 (a) (i)) | 1 |
| Rear Shock absorbers has a serious fluid leak x2 (5.3.2 (b)) | 1 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt SPLIT MARKET WITH YELLOW CHALK (2.1.3 (g) (ii)) | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt INSECURE MARKET WITH YELLOW CHALK (2.1.3 (g) (ii)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL MARKET WITH YELLOW CHALK (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced MARKET IN YELLOW CHALK (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL CORRODED MARKET IN YELLOW CHALK (6.1.1 (c) (i)) | 1 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Headlamp insecure (4.1.1 (c)) | 1 |
| Front Lower Suspension arm pin or bush excessively worn rear bushes both sides (5.3.4 (a) (i)) | 1 |
| Nearside Front Headlamp levelling device inoperative arm missing (4.1.5 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 2 plates (5.3.6 (a) (i)) | 1 |
| Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn D-Bush (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage pin or bush excessively worn D-Bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Inner Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Front Position lamp not working both sides (4.2.1 (a) (ii)) | 1 |
| Nearside Front Lower Suspension component ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt split (6.1.7 (g) (ii)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light shows white light (4.5.4 (a)) | 1 |
| Main beam tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Rear fog lamp tell-tale missing (4.9.1 (a) (ii)) | 1 |
| Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Parking brake: efficiency below requirements (3.7.C.1b) | 1 |
| Nearside Front Front position lamp(s) not working (1.1.A.3b) | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Front Wheel nut(s) missing (4.2.A.1e) | 1 |
| Nearside Rear Wheel nut(s) missing (4.2.A.1e) | 1 |
| Nearside Front Wheel nut(s) missing (4.2.A.1e) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Front Road wheel fixing missing wheel nut (5.2.1 (a) (i)) | 1 |
| Offside Rear Integral body structure is fractured and structural rigidity is significantly reduced inner sill (6.1.1 (a) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced centre
inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Central Rear Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Offside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Offside Front Inner Drive shaft joint constant velocity boot missing (6.1.7 (g) (ii)) | 1 |
| Offside Rear Rear fog lamp switch missing (4.5.3 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer body sills (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer body sill (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Rear fog lamp does not emit a steady red light white bulb fitted (4.5.4 (a)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/chassis rail (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner qaurter (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/chassis rail (6.1.1 (c) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill by slide door (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner qauter (6.1.1 (c) (i)) | 1 |
| Offside Front Drag link end ball joint has excessive play inner tie rod (2.1.3 (b) (i)) | 1 |
| Offside Rear fog lamp does not emit a steady red light omits a white light (4.5.4 (a)) | 1 |
| Offside Exhaust has a major leak of exhaust gases Center exhaust joint (6.1.2 (a)) | 1 |
| Front Suspension arm pin or bush excessively worn both (5.3.4 (a) (i)) | 1 |
| Front Inner Drive shaft joint constant velocity boot missing both (6.1.7 (g) (ii)) | 1 |
| Nearside Track rod end modification unsafe SPLIT PIN MISSING (2.1.3 (f) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect Headlamp fogged over. Lens restoration required (4.1.2 (c)) | 1 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced Headlamp fogged over. Lens restoration required (4.1.4 (b)) | 1 |
| Offside Front Lower Suspension arm likely to become detached bolt and nut loose ball joint (5.3.3 (a) (ii)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light also light lense cracked (4.5.4 (a)) | 1 |
| Offside Rear Position lamp has a product on the lens or light source which shows white light to the rear light lense cracked (4.2.3 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached outer ball joint (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corroded through (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users o/s/f area (source unknown) (8.4.1 (a) (i)) | 1 |
| Nearside Rear Road wheel fixing loose (5.2.1 (a) (i)) | 1 |
| Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis cross member (6.2.2 (d) (i)) | 1 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Track rod end ball joint has excessive play nsf (2.1.3 (b) (i)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Rear fog lamp does not emit a steady red light Showing white light (4.5.4 (a)) | 1 |
| Rear Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Brake performance unable to be tested brake pedal travel to floor (1.2.1 (g)) | 1 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Trailer electrical socket likely to become detached (4.10 (a) (ii)) | 1 |
| Rear Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Power steering malfunctioning (2.1.5 (a)) | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Brake performance unable to be tested (1.2.1 (g)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Outer Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Nearside Front Road wheel more than one fixing loose (5.2.1 (a) (ii)) | 1 |
| Offside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Offside Front Brake hose connection leaking on a hydraulic braking system flexi joint on calliper (1.1.12 (c) (ii)) | 1 |
| Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Nearside Front Lower Suspension arm pin or bush likely to become detached rear bush bonding failed (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Offside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting by spring hanger (6.2.2 (d) (i)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt inner boot split (6.1.7 (g) (ii)) | 1 |
| Offside Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Rear Rear fog lamp obviously incorrectly positioned Does not meet uk spec. (4.5.4 (a)) | 1 |
| Nearside Rear Brake hose connection leaking on a hydraulic braking system Leak at banjo union on caliper (1.1.12 (c) (ii)) | 1 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect Bulb Incorrectly Fitted (4.1.2 (c)) | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt Drop Link (5.3.4 (b) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill Within 30cm of Suspension Mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect Bulb Incorrectly Fitted (4.1.2 (c)) | 1 |
| Brake lever has insufficient reserve travel Parking Brake (1.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Sill Within 30cm of Suspension Mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill at front and rear (5.3.6 (a) (i)) | 1 |
| Outline marker lamp showing red light to the front (4.2.3 (a) (ii)) | 1 |
| Nearside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |