| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 55 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 35 |
| Headlamp aim out of alignment | 24 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 20 |
| Windscreen wiper does not clear the windscreen effectively | 16 |
| Windscreen washer not working | 15 |
| Brakes imbalanced across an axle | 11 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 10 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 9 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 8 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Registration plate lamp issues | 7 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 7 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 7 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 6 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 6 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 6 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 6 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 6 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 5 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 5 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 5 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 5 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 5 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 5 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 4 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 4 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 4 |
| Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 4 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 4 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 3 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Rear parking brake recording little or no effort | 3 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Anti-lock braking system warning lamp indicates an ABS fault | 3 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 3 |
| Registration plate issues | 3 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 3 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Nearside Front Road wheel fixing missing (5.2.1 (a) (i)) | 3 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Nearside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 3 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Engine MIL inoperative or indicates a malfunction (8.2.2.2 (g)) | 3 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 3 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 3 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 3 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 2 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 2 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Rear fog lamp tell-tale missing (4.9.1 (a) (ii)) | 2 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 2 |
| Nearside Rear Shock absorbers has a serious fluid leak | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 2 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Prop shaft bearing excessively worn (6.1.7 (b) (i)) | 2 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Prop shaft flexible coupling excessively deteriorated (6.1.7 (d) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 2 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 2 |
| Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill holed (5.3.6 (a) (i)) | 2 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 2 |
| Rear brake disc in such a condition that it is seriously weakened | 2 |
| Nearside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 2 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front Road wheel fixing missing (5.2.1 (a) (i)) | 2 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Exhaust emissions exceed default limit of 1.5m-1 (8.2.2.2 (b)) | 2 |
| Offside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Brake performance unable to be tested (1.2.1 (g)) | 2 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 2 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Nearside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 2 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Brake load sensing valve linkage defective and function impaired (1.1.17 (a)) | 2 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Rear Coil spring not correctly located |2.4.C.2| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Battery insecure |1.9.1| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded inner and outer sill areas |2.4.A.3| | 1 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Centre Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Outer Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Windscreen wiper blade missing (3.4 (b) (ii)) | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Front Position lamp not working both sides (4.2.1 (a) (ii)) | 1 |
| Front Lower Suspension component ball joint excessively worn both sides (5.3.4 (a) (i)) | 1 |
| Steering rack gaiter missing or no longer prevents the ingress of dirt both sides (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel both sides (1.3.1 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Passengers seat with a defective structure n/s/f inner sill (6.2.6 (a) (i)) | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Rear Suspension component pin or bush excessively worn axle panard rod nearside bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Brake hose damaged | 1 |
| Central Front Brake hose excessively twisted (1.1.12 (b) (ii)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside floor to sill (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside rear inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension arm corroded and seriously weakened spring mountain corroded (5.3.3 (b) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nearside floor to sill X2 places (7.1.1 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength offside rear valance (5.3.6 (a) (i)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Parking brake inoperative on one side neither side is working no handbrake readings (1.4.1 (a)) | 1 |
| Nearside Rear Suspension rod pin or bush excessively worn panard rod (5.3.4 (a) (i)) | 1 |
| Nearside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear reflector defective or damaged by more than 50% of the reflecting surface (4.8.1 (a) (ii)) | 1 |
| Offside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut turret/inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut turret/inner wing (5.3.6 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn Drop link. (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn Drop link. (5.3.4 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill as marked (5.3.6 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill as marked (7.1.1 (a) (i)) | 1 |
| Central Prop shaft bearing housing likely to fail rubber bushing badly torn,and excessive movement present (6.1.7 (f) (ii)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Emissions not tested blue smoke (8.2.2.2 (e)) | 1 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
| Nearside Front Outer Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn outer (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm pin or bush excessively worn Inner (5.3.4 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction inoperative (8.2.2.2 (g)) | 1 |
| Emissions not tested Due to exhaust whole will make the reading incorrect (8.2.2.2 (e)) | 1 |
| Electrical wiring insecure and in contact with sharp edges under bonnet (4.11 (a) (ii)) | 1 |
| Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Nearside Rear Suspension rod pin or bush excessively worn pan hard (5.3.4 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer (5.3.6 (a) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Nearside Rear Inner Integral body structure inadequately repaired such that structural rigidity is significantly reduced sill (6.1.1 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch valance (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch valance (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Parking brake inoperative on one side Nearside and Offside (1.4.1 (a)) | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn rear axle (5.3.4 (a) (i)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a)) | 1 |
| Battery leaking (4.13 (b)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced - Mid-rear lower panel/sill (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced - Mid-rear lower panel/sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced - End panel behind wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced - End panel behind wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Service brake grabbing severely (1.2.1 (c)) | 1 |
| Rear Prop shaft bearing excessively worn (6.1.7 (b) (i)) | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Rear Brake load sensing valve seized and ABS not fitted or inoperative brake compensator valve (1.1.17 (c) (ii)) | 1 |
| Nearside Front Brake disc significantly and obviously worn excessive runout (1.1.14 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn excessive runout and badly corroded inside (1.1.14 (a) (i)) | 1 |
| Brake lever has insufficient reserve travel handbrake pedal goes to floor (1.1.2 (a)) | 1 |
| Offside Front Battery insecure and likely to fall from carrier inside bonnet (4.13 (a) (ii)) | 1 |
| Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen both side (3.5 (a)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Underside of sill. (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Subframe mounting prescribed area excessively corroded significantly reducing structural strength Sill. (5.3.6 (a) (i)) | 1 |
| Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Offside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases Front flexi pipe damaged (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component pin or bush excessively worn Cross support bar bush (outer) (5.3.4 (a) (i)) | 1 |
| Brake cable damaged Both handbrake cables cut in half at rear (1.1.15 (a)) | 1 |
| Front Suspension arm pin or bush excessively worn both sides (5.3.4 (a) (i)) | 1 |
| Nearside Steering locking device missing (2.1.3 (d)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Body modification likely to adversely affect braking or steering (6.2.1 (d) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch holed (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill and outrigger holed (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing, bottom of of suspension turret (5.3.6 (a) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn both rear d bushes (5.3.4 (a) (i)) | 1 |
| Rear Anti-roll bar linkage ball joint excessively worn both rear drop links (5.3.4 (a) (i)) | 1 |
| Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Front Steering rack gaiter missing or no longer prevents the ingress of dirt both front (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn and offside rear "D" bushes (5.3.4 (a) (i)) | 1 |
| Nearside Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases FLEXI PIPE (6.1.2 (a)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength UNDER SILL (5.3.6 (a) (i)) | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg to engine bay (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Headlamp not working on dipped beam Both NSF OSF (4.1.1 (a) (ii)) | 1 |
| Central Prop shaft bearing excessively worn (6.1.7 (b) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Flexy (6.1.2 (a)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Road wheel more than one fixing missing (5.2.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Jacking point inner sill (5.3.6 (a) (i)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced OUTER SILL (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure inadequately repaired such that structural rigidity is significantly reduced Sill patch not fully welded (6.1.1 (d) (i)) | 1 |
| Fuel system component leaking (6.1.3 (b) (i)) | 1 |
| Nearside Front Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases rear silencer (6.1.2 (a)) | 1 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Nearside Front Headlamp light source and lamp not compatible LED bulb fitted (4.1.4 (c)) | 1 |
| Offside Front Headlamp light source and lamp not compatible LED bulb fitted (4.1.4 (c)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Headlamp aim not tested (4.1.2 (b)) | 1 |
| Emissions not tested due to major leak (8.2.2.2 (e)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corroded and holed within 30cm of rear trailing arm bush mounting (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill crushed and corroded within 30cm of rear trailing arm bush mounting (5.3.6 (a) (i)) | 1 |
| Central Prop shaft bearing housing fractured rubber mounting excessively deteriorated (6.1.7 (f) (i)) | 1 |
| Brake servo defective or ineffective (1.1.10 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases rear box broken (6.1.2 (a)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak exhaust broken no readings (8.2.2.1 (b)) | 1 |
| Offside Rear Brake pipe connection leaking on a hydraulic braking system to cylinder (marked in yellow) (1.1.11 (b) (ii)) | 1 |
| Central Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Brake performance unable to be tested due to leaking brake pipe(s) (1.2.1 (g)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill,as marked (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Offside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Central Rear Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill x2 (7.1.1 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Central Rear Brake modification unsafe incorrect brake pipe coupling used (1.1.21 (d) (i)) | 1 |
| Power steering pipe/hose leaking rack joint area (2.1.5 (a)) | 1 |
| Offside Rear Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Brake performance unable to be tested brake pedal spongy (1.2.1 (g)) | 1 |
| Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed (8.2.1.2 (d)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength as marked (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength as marked (5.3.6 (a) (i)) | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength as marked (5.3.6 (a) (i)) | 1 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under sill to floor (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to under sill (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Seat belt not functioning as intended Rear seats and belts cannot be checked (7.1.2 (c)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill (7.1.1 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill front andmiddle (6.1.1 (c) (i)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Rear Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Offside Rear Inner Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Rear Brake cable insecure | 1 |
| Offside Rear Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Emissions unable to be completed exhaust broken (8.2.2.2 (e)) | 1 |
| Offside Front Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Central Prop shaft bearing housing likely to fail (6.1.7 (f) (ii)) | 1 |
| Front Position lamp not working both (4.2.1 (a) (ii)) | 1 |
| Rear fog lamp switch missing (4.5.3 (a)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is inadequately repaired Outer sill in multiple places (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area is inadequately repaired Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/ wheel arch and suspension support corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn Stabilizer bar outer bush delaminated (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Suspension turret (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill to wheel arch. (5.3.6 (a) (i)) | 1 |
| Rear Exhaust system insecure rubber mount (6.1.2 (a)) | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Central Prop shaft likely to become detached mount (6.1.7 (a) (ii)) | 1 |
| Power steering component leaking rack (2.1.5 (a)) | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Rear Anti-roll bar pin or bush excessively worn D-Bushes (5.3.4 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Oil leaking excessively from transmission (8.4.1 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Exhaust system insecure Sleeve Loose (6.1.2 (a)) | 1 |
| Brake hose excessively deteriorated | 1 |
| Power steering component leaking (2.1.5 (a)) | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering all of underbody (6.1.1 (c) (ii)) | 1 |
| Rear Parking brake inoperative on one side both sides (1.4.1 (a)) | 1 |
| Rear Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Rear All position lamps adversely affected by the operation of another lamp all lamps (4.2.3 (c)) | 1 |
| Front Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Anti-lock braking system wiring excessively damaged (1.6 (d)) | 1 |
| Offside Obligatory mirror insecure (3.3 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Suspension rod pin or bush excessively worn Panard rod both N/S bushes (5.3.4 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outrigger to inner sill area. (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outrigger to inner sill area. (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill weak/holed (7.1.1 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill weak/holed (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill weak/holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded in 2 places (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded in 3 places (6.1.1 (c) (i)) | 1 |
| Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill - multiple locations (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill multiple locations (5.3.6 (a) (i)) | 1 |
| Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength trailing arm (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength trailing arm (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL AREA (6.1.1 (c) (i)) | 1 |
| Power steering pipe/hose leaking RACK (2.1.5 (a)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL AREA (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL AREA (6.1.1 (c) (i)) | 1 |
| Offside Rear Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL AREA (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced WHEEL ARCH AREA (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL AREA (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL AREA (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL AREA (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced OUT RIGGER AREA (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Coil spring mounting corroded and seriously weakened Bottom arm (5.3.1 (b) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wing (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wing (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inside strut turret (5.3.6 (a) (i)) | 1 |
| Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Nearside Front Lower Steering locking device missing ball joint split pin missing (2.1.3 (d)) | 1 |
| Offside Front Lower Steering locking device missing split pin missing on arm (2.1.3 (d)) | 1 |
| Nearside Front Upper Macpherson strut top bush or bearing has excessive wear or free play (5.3.4 (a) (i)) | 1 |
| Power steering component leaking rack / box (2.1.5 (a)) | 1 |
| Power steering component insecure rack (2.1.5 (d) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed (7.1.1 (a) (i)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Crossmember heavily corroded & holed (6.1.1 (c) (i)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt Boot damaged & holed (2.1.3 (g) (ii)) | 1 |
| Front Anti-roll bar pin or bush excessively worn Both front Anti Roll bar D bushes worn & knocking (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wing corroded & holed (5.3.6 (a) (i)) | 1 |
| Central Prop shaft bearing housing insecure Rubber bearing mounting split & not attached to housing (6.1.7 (f) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under sill (6.1.1 (c) (i)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill to arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Shock absorbers likely to become detached (5.3.2 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CROSS MEMBER (5.3.6 (a) (i)) | 1 |
| Rear Suspension arm pin or bush excessively worn TRAILING ARM (5.3.4 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Tailpipe joint area (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill area of trailing arm mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill area of trailing arm mounting (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed EXCESSIVE C0 7% AND LAMBDA WAS BELOW 0.97 (8.2.1.2 (d)) | 1 |
| Battery insecure and likely to fall from carrier auxiliary battery (4.13 (a) (ii)) | 1 |
| Nearside Front Coil spring fractured or broken broken (5.3.1 (b) (i)) | 1 |