| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 46 |
| Headlamp aim out of alignment | 29 |
| Registration plate lamp issues | 20 |
| Windscreen wiper does not clear the windscreen effectively | 19 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 14 |
| Offside Rear fog lamp not working |1.3.2b| | 13 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
| Offside Rear Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 10 |
| Nearside Rear Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 10 |
| Registration plate issues | 9 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 9 |
| Service brake: efficiency below requirements |3.7.B.7| | 8 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 8 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 7 |
| Rear Exhaust system not adequately supported |7.1.1| | 7 |
| Brakes imbalanced across an axle | 7 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Parking brake lever has no reserve travel |3.1.6b| | 6 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 6 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 6 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Parking brake: efficiency below requirements |3.7.B.7| | 5 |
| Brake hose excessively deteriorated | 5 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 5 |
| Nearside Rear position lamp|s| incomplete |1.1.4a| | 5 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 4 |
| Nearside Rear Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement |2.4.B.2| | 4 |
| Offside Rear Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement |2.4.B.2| | 4 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 4 |
| Rear brake binding | 4 |
| Rear parking brake recording little or no effort | 4 |
| Rear Rear fog lamp not working |1.3.2b| | 4 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 4 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 4 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 4 |
| Rear fog lamp tell tale not working |1.3.1b| | 4 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Offside Outer Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Exhaust system not adequately supported |7.1.1| | 3 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Brake load sensing valve linkage seized |3.6.E.3| | 3 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Rear Rear fog lamp missing |1.3.2a| | 3 |
| Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 3 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 3 |
| Horn not working |1.6.2a| | 3 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 3 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 3 |
| Nearside Rear Rear position lamp|s| incomplete |1.1.4a| | 2 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Rear brake application uneven | 2 |
| Centre Exhaust system not adequately supported |7.1.1| | 2 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
| Emissions not tested |7.0| | 2 |
| Braking system leaking |3.6.A.1| | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Centre Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Front Shock absorber has an excessively worn bush |2.7.4| | 2 |
| Centre Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Front Shock absorber has an excessively worn bush |2.7.4| | 2 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Rear fog lamp not working |1.3.2b| | 2 |
| Nearside Rear position lamp|s| incorrect colour |1.1.A.3e| | 2 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Rear Mechanical brake component has restricted free movement | 2 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 2 |
| Nearside Front Direction indicator incomplete |1.5.A1b| | 2 |
| Centre Statutory seat belt missing |5.1.1| | 2 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Front Exhaust system not adequately supported |7.1.1| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Rear Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Nearside Front Front suspension has excessive movement at a wishbone pin or bush |2.5.A.1c| | 1 |
| Offside Front Front suspension has excessive movement at a wishbone pin or bush |2.5.A.1c| | 1 |
| Nearside Front Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Front Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Front Shock absorber has negligible damping effect |2.7.5| | 1 |
| Fuel hose leaking |7.2.3| | 1 |
| Body has excessive displacement which may lead to loss of vehicle control |6.1.B.1a| | 1 |
| Nearside Front Torsion bar insecure at an end fixing |2.4.E.2| | 1 |
| Offside Front Torsion bar insecure at an end fixing |2.4.E.2| | 1 |
| Front front brake binding |3.7.B.1| | 1 |
| Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Front Track rod end ball pin shank loose |2.2.B.1c| | 1 |
| Offside Front Track rod end ball pin shank loose |2.2.B.1c| | 1 |
| Offside Front Rear fog lamp flickers when tapped lightly by hand |1.1.6d| | 1 |
| Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear fog lamp missing |1.3.2a| | 1 |
| Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Nearside Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Rear Shock absorber detached |2.7.2b| | 1 |
| Windscreen wiper blade insecure | 1 |
| Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Ball joint has excessive play |2.2.B.1f| | 1 |
| Centre Exhaust has a part missing |7.1.1a| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Centre Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Rear Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement |2.4.B.2| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting nut missing |2.4.G.1| | 1 |
| Offside Rear Lower Vehicle structure has a modification which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Rear Leaf spring fractured |2.4.B.1a| | 1 |
| Nearside Rear Leaf spring fractured |2.4.B.1a| | 1 |
| Offside Rear Lower Shock absorber detached |2.7.2b| | 1 |
| Offside Outer Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded Chassis at spring front hanger. |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded Chassis at spring front hanger. |2.4.A.3| | 1 |
| Braking system leaking Above fuel tank. |3.6.A.1| | 1 |
| Service brake: efficiency below requirements |3.7.D.4| | 1 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Rear Inner Subframe mounting prescribed area is excessively corroded arches /wings |2.4.A.3| | 1 |
| Front Subframe mounting prescribed area is excessively corroded inner wings/arches |2.4.A.3| | 1 |
| Offside Rear Body insecure and dangerous to other road users flat bed bracket bolt loose |6.1.B.1b| | 1 |
| Nearside Front Outer Front position lamp|s| not working sidelamp inop |1.1.A.3b| | 1 |
| Front Direction indicators flashing more than 120 times a minute all more than 120 per minute |1.4.A.2g| | 1 |
| Rear Direction indicators flashing more than 120 times a minute all more than 120 per minute |1.4.A.2g| | 1 |
| Nearside Front Lower Body has a sharp edge caused by corrosion front panel under bumper corroded |6.1.C.1| | 1 |
| Offside Front Lower Body has a sharp edge caused by corrosion panel corroded under bumper |6.1.C.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded off side reae outer sill coorded and holed |5.2.6| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering sill holed and corroded |6.1.A.1| | 1 |
| Front Exhaust has a major leak of exhaust gases silencer leaking |7.1.2| | 1 |
| Front Exhaust system not adequately supported mount broken |7.1.1| | 1 |
| Offside Rear Inner Vehicle structure has excessive corrosion which adversely affects braking or steering sill corroded - holed by fuel tank |6.1.A.1| | 1 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Nearside Rear Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Offside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Fuel pipe leaking |7.2.3| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| All position lamps not working |1.1.A.3b| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Front Ball joint has excessive play |2.2.B.1f| | 1 |
| Rear Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Rear fog lamp does not face the rear |1.3.2a| | 1 |
| Nearside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Centre Rear Spare wheel carrier insecure |6.4.2| | 1 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
| Rear Lower Fuel tank insecure |7.2.1| | 1 |
| Offside Front Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has a modification which adversely affects braking or steering |6.1.A.1| | 1 |
| Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Brake pipe leaking on a hydraulic braking system front to rear brake pipes central chassis (1.1.11 (b) (ii)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Front brake application uneven | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Rear Rear reflector not red in colour |1.5.1d| | 1 |
| Offside Rear Rear reflector not red in colour |1.5.1d| | 1 |
| Offside Front Outer Anti-roll bar linkage cracked |2.4.G.1| | 1 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Rear Towbar component insecure tow bar socket |6.6.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases box |7.1.2| | 1 |
| Front Exhaust has a major leak of exhaust gases section
|7.1.2| | 1 |
| Nearside Rear Leaf spring has a deteriorated anchor pin rubber bush resulting in excessive movement x2 front and rear |2.4.B.2| | 1 |
| Offside Rear Leaf spring has a deteriorated anchor pin rubber bush resulting in excessive movement x2 front and rear |2.4.B.2| | 1 |
| Emissions not tested due to exhaust blowing |7.3.A.1| | 1 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Nearside Rear Direction indicator incomplete |1.5.A1b| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Wheel nut|s| missing |4.2.A.1e| | 1 |
| Nearside Rear Wheel nut|s| missing |4.2.A.1e| | 1 |
| Brake cable has restricted free movement |3.5.1k| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Wheel nut|s| missing |4.2.A.1e| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Offside Rear Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Service brake: efficiency below requirements |3.7.C.1a| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Rear reflector not red in colour |1.5.1d| | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Offside Rear fog lamp does not face the rear |1.3.2a| | 1 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Front brake caliper has restricted free movement |3.5.1k| | 1 |
| Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Offside Fuel system component insecure |7.2.1| | 1 |
| Centre Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired inner wheel arch (5.3.6 (a) (i)) | 1 |
| Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Fuel system component insecure |7.2.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Brake load sensing valve seized |3.6.E.3| | 1 |
| Nearside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Outer Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear fog lamp obviously incorrectly positioned |1.3.2a| | 1 |
| Offside Rear Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Inner Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Windscreen has damage | 1 |
| Nearside Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Rear Lower Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement |2.4.B.2| | 1 |
| Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Mechanical brake component has restricted free movement | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Front Dipswitch operation does not extinguish all main beam headlamps leaving at least one pair of dipped beam headlamps |1.7.4b| | 1 |
| Offside Front Power steering component|s| leaking |2.3.3b| | 1 |
| Nearside Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Steering wheel locking device insecure |2.1.6| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Steering pivot point has excessive play |2.2.B.1g| | 1 |
| Rear Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 1 |
| Rear Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 1 |
| Nearside Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |