Most common failures | No# failures |
---|
Headlamp aim out of alignment | 25 |
Brake hose excessively deteriorated | 17 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 14 |
Windscreen wiper does not clear the windscreen effectively | 12 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
Nearside Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 7 |
Brakes imbalanced across an axle | 7 |
Offside Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 6 |
Nearside Stop lamp not working |1.2.1b| | 5 |
Offside Stop lamp not working |1.2.1b| | 5 |
Parking brake: efficiency below requirements |3.7.B.7| | 5 |
Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
Nearside Rear Trailing arm corroded and seriously weakened |2.4.G.1| | 4 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 4 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Battery insecure |1.9.1| | 3 |
Offside Rear Trailing arm corroded and seriously weakened |2.4.G.1| | 3 |
Rear parking brake recording little or no effort | 3 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 3 |
Registration plate issues | 3 |
Exhaust emissions carbon monoxide content excessive (7.3.B.1a) | 3 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
Service brake: efficiency below requirements |3.7.B.7| | 2 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Indicator tell tale inoperative |1.4.A.2a| | 2 |
Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
Nearside Headlamp insecure |1.7.3| | 2 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Horn not working |1.6.2a| | 2 |
Rear brake application uneven | 2 |
Offside Headlamp insecure |1.7.3| | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Nearside Rear Radius arm corroded and seriously weakened |2.4.G.1| | 2 |
Registration plate lamp issues | 2 |
Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 2 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 2 |
Horn not working (1.6.2a) | 2 |
Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 2 |
Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 2 |
Exhaust system not adequately supported |7.1.1| | 2 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Side repeater not working |1.4.A.2c| | 2 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Rear brake binding | 1 |
Emissions not tested |7.0| | 1 |
Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Rear Stop lamp not working |1.2.1b| | 1 |
Offside Indicator tell tale inoperative |1.4.A.2a| | 1 |
Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
Rear fog lamp not working |1.3.2b| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front Direction indicator incomplete |1.5.A1b| | 1 |
Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Front Lower Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Front Direction indicator incomplete |1.5.A1b| | 1 |
Offside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Nearside Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Nearside Front Direction indicator insecure |1.4.A.2b| | 1 |
Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Front Body has a projection caused by corrosion |6.1.C.1| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
Nearside front brake binding |3.7.B.1| | 1 |
Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Rear Mechanical brake component has restricted free movement | 1 |
Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
Rear fog lamp switch faulty |1.3.1a| | 1 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded outer sill marked in chalk |5.2.6| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill marked in chalk |2.4.A.3| | 1 |
Offside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Rear Radius arm corroded and seriously weakened |2.4.G.1| | 1 |
Offside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Outer Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength sill b post |5.2.6| | 1 |
Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
Offside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
Centre Exhaust system not adequately supported |7.1.1| | 1 |
Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Offside Front Suspension component mounting prescribed area is inadequately repaired |5.3.6 |a| |i|| | 1 |
Nearside Rear Inner Suspension component mounting prescribed area is inadequately repaired arch |5.3.6 |a| |i|| | 1 |
Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Nearside Rear Inner Seat belt anchorage prescribed area is inadequately repaired sill |7.1.1 |a| |i|| | 1 |
Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Offside Front Drive shaft flexible coupling excessively deteriorated |6.1.7 |d| |i|| | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor |5.3.6 |a| |i|| | 1 |
Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 1 |
Bonnet cannot be secured in the closed position |8.4.1| | 1 |
Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Wheelarch body |6.1.B.2| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 1 |
Nearside Front Upper Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded Inner sill near wheelarch |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded Inner sill near wheelarch |2.4.A.3| | 1 |
Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner behind wheelarch |6.1.B.2| | 1 |
Offside Front Body has a sharp edge caused by corrosion Bumper |6.1.C.1| | 1 |
Rear Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
Offside Front Front position lamp(s) not working (1.1.A.3b) | 1 |
Nearside Front Headlamp not working on main beam (1.7.5a) | 1 |
Offside Front Headlamp not working on main beam (1.7.5a) | 1 |
Offside Rear coil spring broken (2.4.C.1a) | 1 |
rear parking (secondary) brakes imbalanced (3.7.B.6b) | 1 |
Offside Front Position lamp not working (4.2.1 (a)) | 1 |
Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Stop lamp(s) not working wrong way (4.3.1 (a) (ii)) | 1 |
Nearside Suspension component mounting prescribed area is inadequately repaired inner and outer sill in places (5.3.6 (a) (i)) | 1 |
Offside Suspension component mounting prescribed area is inadequately repaired inner and outer sill in places (5.3.6 (a) (i)) | 1 |
Brake pipe excessively corroded | 1 |
Nearside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel and binding-investigate (1.3.1 (a) (ii)) | 1 |
Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b) | 1 |
Offside Headlamp aim beam image obviously incorrect (1.8.A.1b) | 1 |
Offside Headlamp insecure (1.7.3) | 1 |
Nearside Front Steering locking device missing (2.2.C.1g) | 1 |
Offside Front Steering locking device missing (2.2.C.1g) | 1 |
Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill holed in few places (6.1.B.2) | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill holed (6.1.B.2) | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill holed (6.1.B.2) | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
Horn not working (7.7 (a)) | 1 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Rear Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 1 |
Nearside Rear Service brake lagging in operation |1.2.1 |d|| | 1 |
Nearside Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
Nearside Front Service brake excessively binding |1.2.1 |f|| | 1 |
Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Offside Rear Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Front Lower Suspension arm attachment bracket/mounting insecure |2.4.G.1| | 1 |
Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Front Steering locking device missing |2.2.C.1g| | 1 |
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Rear Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front position lamp|s| insecure |1.1.A.3a| | 1 |
Offside Front position lamp|s| insecure |1.1.A.3a| | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Front Headlamp insecure |1.7.3| | 1 |
Nearside Front Headlamp aim not tested |1.8.A.1c| | 1 |
Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
Front Exhaust mounting missing |7.1.1b| | 1 |