Most common failures | No# failures |
---|
Headlamp aim out of alignment | 6 |
Windscreen wiper does not clear the windscreen effectively | 5 |
Rear parking brake recording little or no effort | 4 |
Parking brake: efficiency below requirements |3.7.B.7| | 4 |
Registration plate issues | 3 |
Registration plate lamp issues | 3 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Offside Front Obligatory mirror insecure (3.3 (b) (ii)) | 2 |
Windscreen washer not working | 2 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
Brakes imbalanced across an axle | 2 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Offside Front front brake binding |3.7.B.1| | 2 |
Offside Rear fog lamp not working |1.3.2b| | 2 |
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Brake hose excessively deteriorated | 2 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Nearside Front Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Rear brake disc in such a condition that it is seriously weakened | 1 |
Front brake application uneven | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
All direction indicators not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
Offside Front Seat belt installation anchorage insecure (10.1 (d)) | 1 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
Position lamp switch does not operate in accordance with the requirements (4.2.2 (a)) | 1 |
Position lamp not working all around (4.2.1 (a) (ii)) | 1 |
Position lamp switch allows the rear position lamps to be switched off when the headlamps are on (4.2.2 (a)) | 1 |
Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
Dipswitch operation does not deflect all main beam headlamps to make them dipped beams (4.1.3 (b)) | 1 |
Nearside Front Front passenger door cannot be opened from outside the vehicle handle missing (6.2.3 (a)) | 1 |
Nearside Rear Seat belt missing (7.1.2 (a)) | 1 |
Offside Rear Seat belt missing (7.1.2 (a)) | 1 |
Rear Windscreen wiper not working (3.4 (a)) | 1 |
Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
Offside Front Position lamp not working |4.2.1 |a|| | 1 |
Nearside Rear Position lamp not working |4.2.1 |a|| | 1 |
Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 1 |
Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
Nearside Front front brake binding |3.7.B.1| | 1 |
Service brake: efficiency below requirements |3.7.B.7| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded x2 |5.2.6| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner arch x2 |2.4.A.3| | 1 |
Nearside Front Anti-roll bar has excessive play in a pin/bush link arm |2.4.G.2| | 1 |
Offside Front Anti-roll bar has excessive play in a pin/bush link arm |2.4.G.2| | 1 |
Nearside Front Inner Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Inner Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Windscreen has damage | 1 |
Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Steering locking device missing |2.2.C.1g| | 1 |
Nearside Front Trailing arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Lower Vehicle structure has an inadequate repair which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Nearside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Offside Rear Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Centre Rear Exhaust mounting missing |7.1.1b| | 1 |
Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Inner Subframe mounting prescribed area is excessively corroded wing |2.4.A.3| | 1 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Windscreen wiper blade insecure | 1 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt ball joint cover split (5.3.4 (b) (ii)) | 1 |
Offside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt ball joint cover damaged/split (2.1.3 (g) (ii)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer edge of front chassis rail excessively corroded (6.1.1 (c) (i)) | 1 |
Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
Offside Front Body panel insecure lower edge of front wing excessively corroded/insecure (6.2.1 (a) (i)) | 1 |
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt ball joint cover split (5.3.4 (b) (ii)) | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt ball joint cover damaged/split (2.1.3 (g) (ii)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front section of inner wing excessively corroded (5.3.6 (a) (i)) | 1 |
Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
Nearside Front Body panel insecure lower edge of front wing excessively corroded/insecure (6.2.1 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill excessively corroded (5.3.6 (a) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan excessively corroded by inner edge of chassis rail (7.1.1 (a) (i)) | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body panel damaged and likely to cause injury valance area (6.2.1 (a) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch above chassis (6.1.1 (c) (i)) | 1 |
Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
Nearside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Front Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 1 |
Offside Steering rack gaiter split |2.2.D.2d| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
Main beam `tell-tale` not working |1.7.4c| | 1 |
Rear fog lamp tell tale not working |1.3.1b| | 1 |
Hazard warning lamps inoperative |1.4.B.1b| | 1 |
Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
Nearside Track rod end ball joint dust cover missing |2.2.C.1c| | 1 |
Offside Track rod end ball joint dust cover missing |2.2.C.1c| | 1 |
Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
Nearside Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Steering rack insecure |2.2.B.1a| | 1 |
Nearside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |