Most common failures | No# failures |
---|
Headlamp aim out of alignment | 29 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 15 |
Horn not working |1.7.3a| | 10 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 9 |
Registration plate issues | 8 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 8 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 7 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 7 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 6 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 6 |
Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 5 |
Nearside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 5 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 4 |
Throttle operating incorrectly |6.2.1f| | 4 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 4 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 4 |
Front wheel bearings have excessive free play |2.3.5b| | 4 |
Front wheel bearings are excessively rough |2.3.5b| | 3 |
Direction indicators not working |1.5.1c| | 3 |
Direction indicators flashing more than 120 times per minute |1.5.1c| | 3 |
Roller brake test The less effective brake control does not achieve an efficiency of 25% |1.2.2 |a| |i|| | 3 |
Direction indicator flashing more than 120 times per minute |1.5.1c| | 3 |
Offside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 3 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 2 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 2 |
Front shock absorber seal failed and leaking oil |2.3.3| | 2 |
Nearside Front Direction indicators not working |1.5.1c| | 2 |
Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 2 |
Headlamp aim not tested |1.6| | 2 |
Stop lamp remains on when the brake is released |1.3.1e| | 2 |
Brake pedal has inadequate reserve travel |3.1.3b| | 2 |
Handlebar mounting clamp bolt loose |2.1.1a| | 2 |
Rear Brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 2 |
Offside Front Brake disc|s| is excessively distorted |3.2.A1m| | 2 |
Steering headbearing has excessive free play |2.2.2| | 2 |
Front Front position lamp does not illuminate immediately when switched on |1.1.3a| | 2 |
Stop lamp does not illuminate immediately a brake applies front switch |1.3.1a| | 2 |
Front Stop lamp not working (4.3.1 (a) (ii)) | 2 |
Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
Rear Brake effort inadequate at a wheel (1.2.1 (a) (i)) | 2 |
Roller brake test The less effective brake control does not achieve an efficiency of 25% (1.2.2 (a) (i)) | 2 |
Horn not working (7.7 (a)) | 2 |
Nearside Rear Position lamp not working (4.2.1 (a)) | 2 |
Headlamp dipped beam affected by the operation of the horn |1.2.2c| | 1 |
Headlamp main beam affected by the operation of another lamp |1.2.2c| | 1 |
Nearside Rear suspension bearing has excessive free play |2.4.A2a|i|| | 1 |
Offside Rear suspension bearing has excessive free play |2.4.A2a|i|| | 1 |
Nearside Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Offside Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Rear Hydraulic brake control feels spongy |3.1.4a| | 1 |
Brake disc|s| has excessive run out rear disc |3.2.A1m| | 1 |
Rear Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 1 |
Front Brake caliper|s| securing bolt|s| loose |3.2.A1j| | 1 |
Offside Front Direction indicator not working |1.5.1c| | 1 |
Handlebar deformed |2.1.1b| | 1 |
Rear wheel bearings are excessively rough |2.4.A.2c| | 1 |
Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
Position lamp switch insecure |1.1.4b| | 1 |
All direction indicators not working |4.4.1 |a| |ii|| | 1 |
All position lamps not working front and rear |4.2.1 |a|| | 1 |
Offside Front Shock absorber has a serious fluid leak |5.3.2 |b|| | 1 |
Fuel tank insecure security bolt missing |6.1.3 |a| |i|| | 1 |
Rear Brake pedal has inadequate reserve travel |3.1.3b| | 1 |
Rear Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Fuel hose leaking |7.2.1a| | 1 |
Horn not working |7.7 |a| |ii|| | 1 |
Nearside Front Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
Rear reflector on motorcycle missing |1.4.1| | 1 |
Front Steering headbearing has excessive free play |2.2.2| | 1 |
Front Front wheel bearings have excessive free play |2.3.5b| | 1 |
Front Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Nearside Rear Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Rear suspension bearing has excessive free play |2.4.A2a|i|| | 1 |
Sidecar suspension has an insecure unit. |5.2.3a| | 1 |
Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front Front wheel bearings are excessively rough |2.3.5b| | 1 |
Rear Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Nearside Rear Lower Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 1 |
Stop lamp does not emit a steady light |1.3.1b| | 1 |
Front Stop lamp damaged and function impaired |1.3.3a| | 1 |
Stop lamp not working rear control |4.3.1 |a| |ii|| | 1 |
Front Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Front Brake lever cannot be applied smoothly |3.1.3d| | 1 |
Lower Steering headbearing has excessive free play |2.2.2| | 1 |
Headlamp damaged and function impaired |1.2.3a| | 1 |
Rear Rear reflector on motorcycle missing |1.4.1| | 1 |
Front Brake lever has insufficient reserve travel |1.1.2 |a|| | 1 |
Rear Brake lever has insufficient reserve travel |1.1.2 |a|| | 1 |
Front Stop lamp not working |4.3.1 |a| |ii|| | 1 |
Handlebar retaining device loose |2.2.1 |b| |i|| | 1 |
Rear Brake lagging in operation |1.2.1 |d|| | 1 |
Throttle operating incorrectly sticks open does not release on its own |6.2.1f| | 1 |
Stop lamp does not illuminate immediately a brake applies both brakes fail to illuminate stop lamp |1.3.1a| | 1 |
Front position lamp deteriorated and function impaired dip and main beam on at same time but very dull |1.1.1b| | 1 |
Rear position lamp deteriorated and function impaired one out of two bulbs wrong way round brake light filement on |1.1.1b| | 1 |
Rear Wheel spoke cracked. |4.2.1b| | 1 |
Nearside Front Steering linkage has excessive free play |2.2.2| | 1 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Rear suspension component cracked |2.4.A.1a| | 1 |
Front Direction indicator not working |1.5.1c| | 1 |
Nearside Rear Direction indicator insecure |1.5.3b| | 1 |
Offside Rear Direction indicator insecure |1.5.3b| | 1 |
Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Front Hydraulic brake control feels spongy |3.1.4a| | 1 |
Fuel cap mounting flange/sealing method defective |7.2.2c| | 1 |
Stop lamp does not illuminate immediately a brake applies FRONT |1.3.1a| | 1 |
Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 1 |
Nearside Front Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Offside Front Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Offside Rear Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Nearside Rear Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Rear Wheel has an excessively distorted bead rim. |4.2.2| | 1 |
Wheel spoke missing |4.2.1b| | 1 |
Rear Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Rear Brake disc|s| insecure |3.2.A1g| | 1 |
Direction indicator insecure |1.5.3b| | 1 |
Rear reflector on sidecar missing |1.4.1| | 1 |
Front Upper Direction indicator not working |1.5.1c| | 1 |
Front Brake component has restricted free movement and operation is likely to be impeded |3.2.A1h| | 1 |
Stop lamp affected by the operation of another lamp |1.3.2| | 1 |
Handlebar fractured |2.1.1b| | 1 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Offside Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Front Headlamp aim beam image kick-up is to the offside |1.6.1| | 1 |
Rear suspension component loose |2.4.A.1a| | 1 |
Riders seat insecure |6.2.1a| | 1 |
Front Brake disc|s| insecure |3.2.A1g| | 1 |
Offside Rear Footrest insecure |6.2.1a| | 1 |
Centre Front Lower Horn not working |1.7.3a| | 1 |
Nearside Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 1 |
Front Locking devices not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Front Brake excessively binding |1.2.1 |f|| | 1 |
Rear Brake excessively binding |1.2.1 |f|| | 1 |
Front wheel spindle securing nut|s| loose |2.3.3a| | 1 |
Front suspension has excessive stiffness in the suspension movement. |2.3.6b| | 1 |
Centre Direction indicators flashing more than 120 times per minute |1.5.1c| | 1 |
Nearside Front Position lamp switch insecure |1.1.4b| | 1 |
Headlamp aim so that beam "kick up" is not visible on the screen |1.6.B.1| | 1 |
Headlamp aim headlamp deteriorated and function impaired |1.2.3a| | 1 |
Stop lamp remains on when the brakes are released | 1 |
Riders seat insecure |6.2.5 |a| |ii|| | 1 |
Handlebar mounting insecure (2.2.1 (a) (i)) | 1 |
Stop lamp not working front control (4.3.1 (a) (ii)) | 1 |
Front Brake disc contaminated x2 (1.1.14 (b)) | 1 |
Rear Brake pipe likely to become detached or damaged rubbing on frame at rear (1.1.11 (d) (ii)) | 1 |
Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Front Brake excessively binding (1.2.1 (f)) | 1 |
Rear Brake excessively binding (1.2.1 (f)) | 1 |
Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Stop lamp not working both (4.3.1 (a) (ii)) | 1 |
Front Position lamp not working (4.2.1 (a)) | 1 |
Rear Brake component insecure lock nut not tight (1.1.21 (c)) | 1 |
Stop lamp not working off front brake lever (4.3.1 (a) (ii)) | 1 |
Rear Brake lever pivot excessively tight (1.1.1 (a)) | 1 |
Offside Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 1 |
Rear Wheel spindle or securing nut(s) so insecure that wheel security or steering control is adversely affected (5.2.1 (c) (ii)) | 1 |
Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
Front Brake indicates excessive fluctuation of brake effort (1.2.1 (e)) | 1 |
Front Brake excessively binding front and rear (1.2.1 (f)) | 1 |
Nearside Front Brake disc contaminated (1.1.14 (b)) | 1 |
Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Steering damper insecure (2.1.4 (d) (i)) | 1 |
Rear Brake pedal is bent and the brake cannot be readily applied (1.1.2 (d)) | 1 |
Headlamp aim projected beam image obviously incorrect (4.1.2 (c)) | 1 |
Rear Stop lamp with a multiple light source more than 1/2 not functioning (4.3.1 (a) (ii)) | 1 |
Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Stop lamp not working not working on front or rear brake application (4.3.1 (a) (ii)) | 1 |
Rear reflector missing (4.8.2 (a) (ii)) | 1 |
Stop lamp not working rear operation (4.3.1 (a) (ii)) | 1 |