>

MOT History from tests of petrol MORRIS 1300s year 1971

Review the list of common MORRIS 1300 failures below or to perform a specific mot history check on your MORRIS then use our popular KnowYourCar service

mot history
Pass percent:76.69%
(The average a petrol MORRIS 1300 year 1971 passes without issue)
Based on:369 MOT Tests
Most common failuresNo# failures
Brakes imbalanced across an axle14
Registration plate lamp issues12
Headlamp aim out of alignment11
Parking brake: efficiency below requirements |3.7.B.7|10
Offside front brake binding |3.7.B.1|9
Nearside front brake binding |3.7.B.1|8
Windscreen wiper does not clear the windscreen effectively7
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3|6
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3|6
Nearside Stop lamp not working |1.2.1b|6
Offside Stop lamp not working |1.2.1b|6
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a|5
Brake hose excessively deteriorated5
Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a|4
Brake pipe excessively corroded4
Service brake: efficiency below requirements |3.7.B.7|4
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3|4
Rear brake binding4
Offside Front Lower Ball joint has excessive play |2.2.B.1f|3
Rear parking brake recording little or no effort3
Horn not working |1.6.2a|3
Nearside Front front brake binding |3.7.B.1|3
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3|2
Nearside Side repeater not working |1.4.A.2c|2
Nearside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a|2
Exhaust has a major leak of exhaust gases |7.1.2|2
Front brake application uneven2
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b|2
Offside rear brake recording little or no effort |3.7.B.5a|2
Offside Front Headlamp not working on dipped beam |1.7.5a|2
Nearside rear brake recording little or no effort |3.7.B.5a|2
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c|2
Nearside Front Direction indicator not working |1.4.A.2c|2
Centre Exhaust system not adequately supported |7.1.1|2
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2|2
Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a|2
Exhaust system not adequately supported |7.1.1|2
Rear brake application uneven2
Offside Front front brake binding |3.7.B.1|2
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3|2
Offside Headlamp not working on main beam |1.7.5a|2
Offside Front Track rod end ball joint has excessive play |2.2.B.1f|1
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3|1
Offside Fluid suspension has no suspension movement |2.4.D.5|1
Offside Fluid suspension leaking |2.4.D.2|1
Registration plate issues1
Seat belt anchorage prescribed area is excessively corroded |5.2.6|1
Rear Sub-frame corroded and seriously weakened |2.4.G.1|1
Offside Front Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2|1
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3|1
Offside Front wheel bearing has excessive play |2.5.A.3c|1
Offside Front Hazard warning lamps inoperative |1.4.B.1b|1
Nearside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a|1
Windscreen wiper not operating automatically when switched on |8.2.1b|1
Hazard warning tell tale not working correctly |1.4.B.1e|1
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b|1
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2|1
Nearside Front Headlamp not working on dipped beam |1.7.5a|1
Nearside Front Headlamp aim not tested |1.8.A.1c|1
Offside Front Headlamp aim not tested |1.8.A.1c|1
Battery insecure |1.9.1|1
Rear Fuel pipe leaking |7.2.3|1
Nearside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a|1
Nearside Front Lower brake caliper securing device loose |3.5.1j|1
Offside Front Lower brake caliper securing device loose |3.5.1j|1
Fuel system component leaking |7.2.3|1
Front engine mounting deteriorated resulting in excessive movement |6.1.D.1a|1
Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b|1
Nearside Rear wheel bearing rough when rotated |2.6.1|1
Fuel cap/sealing device sealing washer missing |7.2.4c|1
Offside Rear Stop lamp not working |1.2.1b|1
Nearside Rear Rear position lamp|s| not working |1.1.A.3b|1
Offside Side repeater excessively deteriorated so that it is not visible from a reasonable distance |1.4.A.2e|1
Nearside Front Front wheel bearing has excessive play |2.5.A.3c|1
Nearside Front Seat belt retracting mechanism defective |5.2.5b|1
Offside Front Seat belt retracting mechanism defective |5.2.5b|1
Mechanical brake component has restricted free movement1
Nearside Rear Subframe mounting prescribed area is excessively corroded sub frame in front of rear wheel on top |2.4.A.3|1
Offside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a|1
Offside Front Brake hose leaking |3.6.A.1|1
Front Brake master cylinder insecurely mounted |3.6.G.1a|1
Nearside Front Side repeater not working |1.4.A.2c|1
Offside Front Side repeater not working |1.4.A.2c|1
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3|1
Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3|1
Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3|1
Nearside Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2|1
Offside Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2|1
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3|1
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3|1
Front position lamp|s| not working |1.1.A.3b|1
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b|1
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b|1
Offside Front Statutory seat belt missing |5.1.1|1
Nearside Front Statutory seat belt missing |5.1.1|1
Exhaust has a major leak of exhaust gases at joint between front pipe and manifold |7.1.2|1
Stop lamp remains on when the brakes are released1
Sub-frame rubber bush deteriorated resulting in excessive movement all four rubber bushes on front subframe |2.4.G.2|1
Fuel system component leaking from around sender unit and fuel pipes at rear of car |7.2.3|1
Nearside Rear Trailing arm has excessive play in a pin/bush |2.4.G.2|1
Electrical wiring insecure positive battery terminal bolt |1.9.2a|1
Electrical wiring insecure wire hanging down by offside front wheel in the arch |1.9.2a|1
Offside Front brake caliper securing device loose |3.5.1j|1
Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a|1
Offside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a|1
Nearside Front Front suspension locking device ineffective |2.5.A.4|1
Nearside Front Front drive shaft coupling flexible rubber or fabric coupling unit breaking up |2.5.C.1d|1
Stop lamp not working |1.2.1b|1
Offside Front Upper Body has a sharp edge caused by corrosion |6.1.C.1|1
Nearside Inner Rear Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3|1
Nearside Rear Sub-frame attachment bracket/mounting insecure |2.4.G.1|1
Offside Front Fluid suspension accumulator deteriorated and likely to fail |2.4.D.1b|1
Nearside Front Fluid suspension accumulator deteriorated and likely to fail |2.4.D.1b|1
Offside Rear Fluid suspension accumulator deteriorated and likely to fail |2.4.D.1b|1
Nearside Rear Fluid suspension accumulator deteriorated and likely to fail |2.4.D.1b|1
Nearside front brake recording little or no effort |3.7.B.5a|1
Nearside Rear rear brake recording little or no effort |3.7.B.5a|1
Nearside Steering arm has relative movement at its fixings Rack arm. |2.2.B.1h|1
Direction indicators flashing less than 60 times a minute |1.4.A.2g|1
Driver`s seat insecure |6.2.A.1|1
Brake performance not tested Non start end of test (1.2.1 (g))1
All direction indicators not working (4.4.1 (a) (ii))1
Hazard warning lamps inoperative |1.4.B.1b|1
Offside Front Lower Radius arm has excessive play in a ball joint |2.4.G.2|1
Offside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i||1
Offside Front Upper Ball joint has excessive play |2.2.B.1f|1
Offside Rear rear brake recording little or no effort |3.7.B.5a|1
Offside Front Upper Suspension component mounting prescribed area is fractured |2.4.A.3|1
Rear Exhaust has part of the system excessively deteriorated |7.1.1a|1
Rear Fuel pipe union leaking (6.1.3 (b) (i))1
Service brake efficiency below requirements (1.2.2 (a) (i))1
Offside Front Subframe mounting prescribed area is excessively corroded floor |2.4.A.3|1
Nearside Rear Subframe mounting prescribed area is excessively corroded marked |2.4.A.3|1
Offside Front Subframe mounting prescribed area is excessively corroded under wing trumpet marked |2.4.A.3|1
Nearside Front Subframe mounting prescribed area is excessively corroded under wing trumpet marked |2.4.A.3|1
Offside Rear Subframe mounting prescribed area is excessively corroded marked |2.4.A.3|1
Offside Front Front position lamp|s| not working |1.1.A.3b|1
Offside Front Direction indicator not working |1.4.A.2c|1
Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c|1
Nearside Front Lower Suspension arm ball joint dust cover missing |2.4.G.2|1
Nearside Front Front drive shaft coupling flexible rubber or fabric coupling softened by oil contamination |2.5.C.1e|1
Front Fuel hose leaking |7.2.3|1
Offside Front Front drive shaft coupling flexible rubber or fabric coupling unit breaking up |2.5.C.1d|1
Nearside Front position lamp|s| not working |1.1.A.3b|1
Offside Windscreen wiper blade deteriorated |8.2.2|1
Offside Rear Brake pedal does not operate a brake fitted to each wheel |3.3.A.3|1
Offside Rear Service brake application uneven across the axle |3.7.D.2b|1
Service brake: efficiency below requirements |3.7.C.1a|1
Brake pedal has insufficient reserve movement |3.3.A.5|1
Rear Passenger`s seat insecure |6.2.A.1|1
Offside Front constant velocity joint gaiter split |2.5.C.1a|1
Offside Steering rack gaiter split |2.2.D.2d|1
Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings o/s sille front end |6.1.B.2|1
Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s sille rear end |6.1.B.2|1
Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc n/sfront |2.5.C.1a|1
Front Exhaust has a major leak of exhaust gases |7.1.2|1
Offside Front brake disc excessively pitted |3.5.1h|1
Nearside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2|1
Nearside rear brake juddering severely |3.7.A.5b|1
Offside rear brake juddering severely |3.7.A.5b|1
Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a|1
Offside Rear Fuel system component leaking |7.2.3|1
Offside Front Sub-frame attachment rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2|1
Offside Front Braking system leaking |3.6.A.1|1
Nearside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d|1
Fuel tank leaking |7.2.3|1
Nearside Headlamp not working on dipped beam |1.7.5a|1
Offside Headlamp not working on dipped beam |1.7.5a|1
Nearside Headlamp not working on main beam |1.7.5a|1
Exhaust has part of the system excessively deteriorated |7.1.1a|1
Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3|1
Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3|1

We get to these numbers by trawling through over 1 billion MOT test results since 2004 and crunched the numbers. We remove anything to do with Tyres, as they are model independent and group together common non-model specific issues. We are trying to get to a picture of what models have what issues.

Please note: We take the data from the DVSA. This data is raw and can contain typos and spelling mistakes that garages may have entered while recording a MOT result. Specifically miss-match on names of models and makes. We are constantly cleaning the data so bear with the odd issue.

Got suggestions? We’re improving this section all the time. If you have any suggestions, please let us know.

Find us on Facebook

© KnowYourCar™ 2019. All rights reserved
Except where otherwise noted, content on our MOT statistics pages are licensed under a Creative Commons Attribution 4.0 International license.
You are free to redistribute the material in any medium or format as long as credit is given to KnowYourCar

WARNING: We have placed hidden watermarks in our data. We will take action against our data being used outside of these terms.

MOT Data licensed under the Open Government Licence v3.0

By using our site you are agreeing to our terms and conditions
Terms & Conditions  Privacy Policy