| Most common failures | No# failures |
|---|
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 18 |
| Brakes imbalanced across an axle | 16 |
| Registration plate issues | 12 |
| Windscreen wiper does not clear the windscreen effectively | 10 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 9 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 7 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 6 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 6 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 6 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 5 |
| Headlamp aim out of alignment | 5 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Emissions not tested (8.2.1.2 (d)) | 4 |
| Brake pipe excessively corroded | 4 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 4 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 4 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Battery insecure |1.9.1| | 4 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 3 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Service brake: efficiency below requirements |3.7.B.7| | 3 |
| Offside Steering rack gaiter split |2.2.D.2d| | 3 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Registration plate lamp issues | 3 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 2 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Offside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 2 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Headlamp aim not tested (4.1.2 (b)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
| Rear fog lamp not working |1.3.2b| | 2 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 2 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 2 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 2 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 2 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Windscreen washer not working | 2 |
| Offside Side repeater incorrect colour (4.4.3 (a)) | 1 |
| Nearside Side repeater incorrect colour (4.4.3 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg near rear anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg near rear anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg excessive corrosion near tie bar mounting point (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg excessive corrosion near tie bar mounting point (5.3.6 (a) (i)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Dipswitch operation does not deflect all main beam headlamps to make them dipped beams (4.1.3 (b)) | 1 |
| Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
| Front Position lamp not working both (4.2.1 (a) (ii)) | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt Gaiter Split (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D-Bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Side repeater not working side ind (4.4.1 (a) (ii)) | 1 |
| Offside Rear Parking brake inoperative on one side low reading (1.4.1 (a)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Offside Front Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect no beam pattern (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect no beam pattern (4.1.2 (c)) | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn trailing arm (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension arm pin or bush excessively worn trailing arm (5.3.4 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak front pipe (8.2.2.1 (b)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Rear parking brake recording little or no effort | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Horn not working |1.6.2a| | 1 |
| Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Nearside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 1 |
| Fuel tank leaking (6.1.3 (b) (i)) | 1 |
| Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced holed within 30cm of axle mount (6.1.1 (c) (i)) | 1 |
| Nearside Rear Passengers seat backrest cannot be secured in the upright position. seat back insecure (6.2.6 (a) (i)) | 1 |
| Nearside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp lens seriously defective misted (4.1.1 (b) (ii)) | 1 |
| Offside Front Headlamp lens seriously defective misted (4.1.1 (b) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Rear Exhaust shield missing where fitted as original equipment creating a risk of fire (6.1.3 (e)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Position lamp has a product on the lens or light source which significantly reduces light intensity (4.2.3 (b) (ii)) | 1 |
| Offside Front Position lamp has a product on the lens or light source which significantly reduces light intensity (4.2.3 (b) (ii)) | 1 |
| Nearside Rear Position lamp has a product on the lens or light source which significantly reduces light intensity (4.2.3 (b) (ii)) | 1 |
| Offside Rear Position lamp has a product on the lens or light source which significantly reduces light intensity (4.2.3 (b) (ii)) | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Marked in yellow (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Rear Rear fog lamp missing |1.3.2a| | 1 |
| Offside Front All position lamps not working |1.1.A.3b| | 1 |
| Nearside Rear All position lamps not working |1.1.A.3b| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is inadequately repaired wheel arch (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases FRONT FLEX (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER W/ARCH (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER W/ARCH (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed Will not maintain constant revs ALL READINGS HIGH CO,HC,LAMDA (8.2.1.2 (d)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near trailing arm in wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near trailing arm in wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt insecure (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Axle swivel pins and bushes swivel pin and/or bush excessively worn (5.1.2 (b) (i)) | 1 |
| Offside Rear Axle swivel pins and bushes swivel pin and/or bush excessively worn (5.1.2 (b) (i)) | 1 |
| Nearside Rear Suspension rod pin or bush excessively worn lower rod inner bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension rod pin or bush excessively worn lower rod inner bush (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension arm mounting has an unsafe modification bracket incorrectly fitted (5.3.3 (c) (i)) | 1 |
| Front Anti-roll bar pin or bush excessively worn nearside and offside (5.3.4 (a) (i)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt split (6.1.7 (g) (ii)) | 1 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s front floor pan (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear 1/4 inner wheel arch lower o/s (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear 1/4 inner wheel arch lower n/s (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s inner wheel arch repair (5.3.6 (a) (i)) | 1 |
| Axle swivel pins and bushes swivel pin and/or bush excessively worn axle rod bushes (5.1.2 (b) (i)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
| Offside Rear Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Hydraulic brake calliper leaking flexi hose seal to calliper (1.1.16 (b) (i)) | 1 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 1 |
| Rear Service brake effort inadequate at a wheel both sides (1.2.1 (a) (i)) | 1 |
| Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt both sides (2.1.3 (g) (ii)) | 1 |
| Front Steering rack gaiter missing or no longer prevents the ingress of dirt both sides (2.1.3 (g) (ii)) | 1 |
| Offside Rear Macpherson strut insecurely attached lower bolt loose (5.3.3 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Rear Outer Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Outer Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Emissions not tested major leak from exhaust (8.2.1.2 (d)) | 1 |
| Rear Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front An item not tested |Manual| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Nearside Rear fog lamp missing |1.3.2a| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Headlamp light source and lamp not compatible HID bulb in halogen headlamp (4.1.4 (c)) | 1 |
| Emissions unable to be completed (8.2.1.2 (d)) | 1 |
| Front Position lamp not working both side (4.2.1 (a) (ii)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both side (4.1.4 (b)) | 1 |
| Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn inner edge (1.1.14 (a) (i)) | 1 |
| Offside Rear Brake hose excessively twisted (1.1.12 (b) (ii)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits 2.87 (8.2.1.2 (a)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits 1187 ppm (8.2.1.2 (b)) | 1 |
| Offside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Chassis leg exhaust hanger section (6.2.2 (d) (i)) | 1 |
| Nearside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Chassis leg (6.2.2 (d) (i)) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Outer entire sill (6.2.2 (d) (i)) | 1 |
| Nearside Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Entire sill (6.2.2 (d) (i)) | 1 |
| Rear brake disc in such a condition that it is seriously weakened | 1 |
| Nearside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Sill /arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Arch by filler tube (6.2.2 (d) (i)) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Inner sill to floor (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Sill to floor pan (6.2.2 (d) (i)) | 1 |
| Brake lever has insufficient reserve travel Handbrake (1.1.2 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to floor holed within 30cm of seatbelt anchor seat support (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front of wheel tub holed and corroded within 30cm of suspension support (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing panel holed within 30cm of strut support and also engine mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel tub holed within 30cm of seatbelt anchorage (7.1.1 (a) (i)) | 1 |
| Emissions not tested due to excessive exhaust leak (8.2.1.2 (d)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength quarter panel holed within 30cm of antiroll bar support (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front of wheel tub holed within 30cm of suspension support (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases at front pipe from both flexi hoses (6.1.2 (a)) | 1 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill excessivly holed and corroded within 30cm of suspension support (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill excessivly holed and corroded within 30cm of suspension support (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill excessivly holed and corroded within 30cm of suspension support (5.3.6 (a) (i)) | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases at middle section joining to back box (6.1.2 (a)) | 1 |