| Most common failures | No# failures |
|---|
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 12 |
| Brake pipe excessively corroded | 12 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 11 |
| Brakes imbalanced across an axle | 11 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 8 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 8 |
| Parking brake: efficiency below requirements |3.7.B.7| | 7 |
| Headlamp aim out of alignment | 6 |
| Windscreen wiper does not clear the windscreen effectively | 5 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 5 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 4 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 4 |
| Rear parking brake recording little or no effort | 4 |
| Registration plate lamp issues | 4 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 4 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 3 |
| Battery insecure |1.9.1| | 3 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Service brake: efficiency below requirements |3.7.B.7| | 3 |
| Offside Steering rack gaiter split |2.2.D.2d| | 3 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 3 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 3 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Emissions not tested (8.2.1.2 (d)) | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| Steering column movement between the shaft and steering wheel |2.1.2b| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Front brake application uneven | 2 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 2 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 2 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 2 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Rear fog lamp switch missing (4.5.3 (a)) | 1 |
| Nearside Rear Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL AREA,BY SUSPENSION POINT,MARKED IN 2 PLACES (6.1.1 (c) (i)) | 1 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Headlamp insecure (4.1.1 (c)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Electrical wiring damaged, likely to become detached |1.9.2b| | 1 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Horn not working |1.6.2a| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear brake caliper has restricted free movement |3.5.1k| | 1 |
| Offside Rear brake caliper has restricted free movement |3.5.1k| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Emissions not tested |7.3.A.1| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
| Nearside Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside Front All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Macpherson strut top bush or bearing has excessive wear or free play (5.3.4 (a) (i)) | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front position lamp|s| insecure |1.1.A.3a| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting INNER WHEEL ARCH,MARKED (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting BY ENGINE,NORTH/SOUTH ENGINE SUPPORT.MARKED (6.2.2 (d) (i)) | 1 |
| Nearside Rear Stop lamp(s) not working CENTRAL LAMP (4.3.1 (a) (ii)) | 1 |
| Upper Steering column attachment defective (2.2.2 (d) (i)) | 1 |
| Lower Steering column universal joint insecure LOWER JOINT AS IT JOINS RACK (2.1.3 (a) (i)) | 1 |
| Nearside Front Sub-frame attachment bracket/mounting fractured MARKED,INCORRECTLY FITTED (5.3.3 (b) (ii)) | 1 |
| Offside Front Sub-frame attachment bracket/mounting likely to fail MARKED,INCORRECTLY FITTED (5.3.3 (b) (ii)) | 1 |
| Central Front Body component damaged and likely to cause injury BONNET SECTION DAMAGED (6.2.1 (a) (i)) | 1 |
| Nearside Rear Position lamp not working CENTRAL LAMP (4.2.1 (a) (ii)) | 1 |
| Emissions not tested |7.0| | 1 |
| Front Body insecure and dangerous to other road users Bumper missing |6.1.B.1b| | 1 |
| Registration plate issues | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Windscreen wiper blade insecure | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Brake fluid warning lamp illuminated |3.6.G.2| | 1 |
| Offside Front Braking system leaking |3.6.A.1| | 1 |
| Offside Front brake caliper leaking |3.6.A.1| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Offside Rear Seat belt missing (7.1.2 (a)) | 1 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.2.1 (a)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect headlamps perished (4.1.2 (c)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Rear Service brake effort inadequate at a wheel Both (1.2.1 (a) (i)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Flexi (6.1.2 (a)) | 1 |
| Offside Vehicle structure inadequately repaired such that structural rigidity is significantly reduced Sill (6.1.1 (d) (i)) | 1 |
| Nearside Vehicle structure inadequately repaired such that structural rigidity is significantly reduced Sill (6.1.1 (d) (i)) | 1 |
| Speedometer cannot be illuminated (7.8 (c) (ii)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Rear Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 1 |
| Nearside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect no head lamp pattern (4.1.2 (c)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect no head lamp pattern (4.1.2 (c)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn drop link (5.3.4 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect no pattern (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect no pattern (4.1.2 (c)) | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Emissions unable to be completed due to missfire (8.2.1.2 (d)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength roll bar bracket (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength roll bar bracket (5.3.6 (a) (i)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Nearside All direction indicators not working Will not switch off - permanently on. (4.4.1 (a) (ii)) | 1 |
| Offside All direction indicators not working Will not switch on. (4.4.1 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill panel - marked. (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Panel inside wheel arch - marked. (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected floor and outrigger (5.3.6 (a) (ii)) | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Emissions unable to be completed (8.2.1.2 (d)) | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Steering pivot point has excessive play |2.2.B.1g| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Rear Rear fog lamp missing |1.3.2a| | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases Middle section (6.1.2 (a)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Centre Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill and under sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing behind wheel (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis behind wheel (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Emissions not tested noise on engine (8.2.1.2 (d)) | 1 |
| Nearside Front Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Offside Front Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Nearside Rear Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Offside Rear Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill at rear. (6.1.1 (c) (i)) | 1 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel Arch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel Arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Marked in Yellow (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Marked in Yellow, Above Exhaust (6.1.1 (c) (i)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |