| Most common failures | No# failures |
|---|
| Brakes imbalanced across an axle | 4 |
| Registration plate issues | 3 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Brake pipe excessively corroded | 2 |
| Horn sound not in accordance with requirements (7.7 (c)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 2 |
| Offside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Front Inner Prop shaft joint constant velocity boot no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values plate limit 3.00 failed 6.50 (8.2.2.2 (f)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Rear Anti-roll bar attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Windscreen wiper does not clear the windscreen effectively | 1 |
| Offside Windscreen wiper not working (3.4 (a)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Rear Service brake effort inadequate at a wheel Both (1.2.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1 |
| Registration plate lamp issues | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |