Most common failures | No# failures |
---|
Headlamp aim out of alignment | 66 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 53 |
Service brake: efficiency below requirements |3.7.B.7| | 33 |
Parking brake: efficiency below requirements |3.7.B.7| | 29 |
Windscreen wiper does not clear the windscreen effectively | 27 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 26 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 25 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 23 |
Offside Rear fog lamp not working |1.3.2b| | 22 |
Brakes imbalanced across an axle | 18 |
Registration plate lamp issues | 18 |
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 17 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 14 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 14 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 13 |
Rear parking brake recording little or no effort | 12 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 12 |
Rear brake binding | 11 |
Offside rear brake recording little or no effort |3.7.B.5a| | 11 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 11 |
Driver`s seat insecure |6.2.A.1| | 10 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 10 |
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Brake pipe excessively corroded | 8 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 8 |
Registration plate issues | 8 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 7 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
Offside Rear Braking system leaking |3.6.A.1| | 6 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 6 |
Nearside Stop lamp not working |1.2.1b| | 6 |
Offside Stop lamp not working |1.2.1b| | 6 |
Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 6 |
Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
Offside Rear rear brake recording little or no effort |3.7.B.5a| | 5 |
Brake pedal anti-slip provision missing |3.3.A.1b| | 5 |
Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 5 |
Exhaust engine idle speed too high |7.3.A.2a| | 5 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 4 |
Rear brake application uneven | 4 |
Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 4 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 4 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 4 |
Battery insecure |1.9.1| | 4 |
Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 4 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
Front Exhaust system not adequately supported |7.1.1| | 4 |
Offside Rear Rear fog lamp not working |1.3.2b| | 4 |
Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 4 |
Offside Headlamp not working on dipped beam |1.7.5a| | 4 |
Nearside Side repeater not working |1.4.A.2c| | 4 |
Horn not working |1.6.2a| | 4 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 4 |
Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
Rear Statutory seat belt missing |5.1.1| | 3 |
Offside Front Side repeater not working |1.4.A.2c| | 3 |
Offside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 3 |
Exhaust emissions hydrocarbon content excessive |8.2.1.2 |b|| | 3 |
Parking brake lever has no reserve travel |3.1.6b| | 3 |
Offside Side repeater not working |1.4.A.2c| | 3 |
Emissions not tested |7.0| | 3 |
Windscreen has damage | 3 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Nearside Front Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 3 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 3 |
Rear fog lamp tell tale not working |1.3.1b| | 3 |
Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 3 |
Nearside Rear Braking system leaking |3.6.A.1| | 3 |
Front Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 3 |
Offside Front Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 3 |
Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 3 |
Nearside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Front Exhaust mounting missing |7.1.1b| | 2 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Nearside Rear An item not tested |Manual| | 2 |
Hazard warning switch faulty |1.4.B.1d| | 2 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 2 |
Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Offside Rear Stop lamp not working |1.2.1b| | 2 |
Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Headlamp insecure |1.7.3| | 2 |
Nearside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 2 |
Nearside Rear Stop lamp not working |1.2.1b| | 2 |
Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
Centre Front Exhaust system not adequately supported |7.1.1| | 2 |
Nearside Inner Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
Offside Windscreen wiper blade deteriorated |8.2.2| | 2 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Hazard warning tell tale not working correctly |1.4.B.1e| | 2 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 2 |
Offside Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
An item not tested |Manual| | 2 |
Nearside Front passenger seat cannot be secured in the upright position. |6.2.4| | 2 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Front passenger seat insecure |6.2.3| | 2 |
Nearside Rear Statutory seat belt missing |5.1.1| | 2 |
Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 2 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
Nearside Front Direction indicator not working |1.4.A.2c| | 2 |
rear brake recording little or no effort |3.7.B.5a| | 2 |
Steering column flexible coupling is excessively deteriorated |2.1.5| | 2 |
Windscreen washer not working | 2 |
Nearside Front Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 2 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 2 |
Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 2 |
Offside Front Fluid suspension has no suspension movement |2.4.D.5| | 2 |
Offside Rear Fluid suspension has no suspension movement |2.4.D.5| | 2 |
Offside Steering rack gaiter split |2.2.D.2d| | 2 |
Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
Horn not loud enough to be heard by another road user |1.6.2b| | 2 |
Offside Front Headlamp aim beam image too far to the left |1.6.B4| | 2 |
Nearside Front Headlamp aim beam image too far to the right |1.6.B4| | 2 |
Offside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 2 |
Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 2 |
Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Front brake application uneven | 2 |
Exhaust emits excessive dense blue smoke during acceleration |7.3.A.2c| | 2 |
Nearside Outer Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
Offside Headlamp insecure |1.7.3| | 2 |
Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 2 |
Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
Rear Stop lamp not working |1.2.1b| | 1 |
Offside Rear An item not tested |Manual| | 1 |
Offside Rear Brake linkage has restricted free movement |3.5.1k| | 1 |
Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Lower Brake hose excessively damaged |3.6.B.4d| | 1 |
Offside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt insecure (6.1.7 (g) (ii)) | 1 |
Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Nearside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Trailing arm has excessive play in a ball joint |2.4.G.2| | 1 |
Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Nearside Front suspension retaining device ineffective |2.5.A.4| | 1 |
Offside Front suspension retaining device ineffective |2.5.A.4| | 1 |
Front Upper Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear passenger seat cannot be secured in the upright position. |6.2.3| | 1 |
Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mounting (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mounting (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength front mounting (5.3.6 (a) (i)) | 1 |
Nearside Fluid suspension has no suspension movement |2.4.D.5| | 1 |
Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Rear fog lamp switch faulty |1.3.1a| | 1 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Electrical wiring deteriorated, likely to cause a short |1.9.2b| | 1 |
Offside Electrical wiring deteriorated, likely to cause a short |1.9.2b| | 1 |
Nearside Front Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Steering rack gaiter split |2.2.D.2d| | 1 |
Upper Steering column deformed and unserviceable |2.2.C.1d| | 1 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Nearside Rear Hydraulic fluid leaking excessively brake. (8.4.1 (a) (i)) | 1 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
Nearside Side repeater missing |1.4.A.2b| | 1 |
Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
Offside Outer Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Direction indicator not working |1.4.A.2c| | 1 |
Offside Rear Subframe mounting prescribed area is excessively corroded in wheel arch |2.4.A.3| | 1 |
Offside Rear Rear position lamp|s| incomplete |1.1.4a| | 1 |
Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Front Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Offside Front Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Front Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
Steering column top bearing excessively worn |2.1.2c| | 1 |
Steering column movement between the shaft and steering wheel |2.1.2b| | 1 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear Passenger`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Front Lower Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front brake caliper securing device missing |3.5.1j| | 1 |
Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Brake pipe inadequately clipped |3.6.B.1| | 1 |
Offside brake disc in such a condition that it is seriously weakened |3.5.1i| | 1 |
Fuel system component insecure |7.2.1| | 1 |
Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
rear brake recording little or no effort Both rear |3.7.B.5a| | 1 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Fluid suspension unit supply pipe corroded and seriously weakened |2.4.D.3| | 1 |
Offside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
Nearside An item not tested |Manual| | 1 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
Centre Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Nearside Indicator tell tale inoperative |1.4.A.2a| | 1 |
Offside Indicator tell tale inoperative |1.4.A.2a| | 1 |
Hazard warning switch missing |1.4.B.1d| | 1 |
Nearside Rear Subframe mounting prescribed area is inadequately repaired sill |2.4.A.3| | 1 |
Nearside Rear Subframe mounting prescribed area is deliberately modified which significantly reduces the original strength back of sill |2.4.A.3| | 1 |
Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Lower Steering column flexible coupling is excessively deteriorated |2.1.5| | 1 |
Nearside Rear brake drum contaminated by brake fluid |3.5.1h| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded arch area |2.4.A.3| | 1 |
rear brake excessively fluctuating |3.7.B.3| | 1 |
Offside rear brakes release unevenly |3.7.B.4| | 1 |
Rear Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded mid floor |2.4.A.3| | 1 |
Offside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Nearside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
Nearside Suspension component mounting prescribed area is excessively corroded boot floor |2.4.A.3| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded boot floor |2.4.A.3| | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded floor to sill |2.4.A.3| | 1 |
Nearside Suspension component mounting prescribed area is excessively corroded floor to sill |2.4.A.3| | 1 |
Rear Suspension component mounting prescribed area is excessively corroded valance by anti roll bar |2.4.A.3| | 1 |
Nearside Front Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Offside Front Brake actuating linkage mounting prescribed area is excessively corroded |3.3.A.2| | 1 |
Front Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Inner Ball joint has excessive play rack end |2.2.B.1f| | 1 |
Offside Rear Subframe mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
Nearside Rear Service brake lagging in operation |1.2.1 |d|| | 1 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Nearside Rear Subframe mounting prescribed area is excessively corroded floor to inner sill |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in boot (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in boot (5.3.6 (a) (i)) | 1 |
Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength fuel filler area (5.3.6 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Suspension arm pin or bush excessively worn radius arm (5.3.4 (a) (i)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced "A" pillar (6.1.1 (c) (i)) | 1 |
Nearside Front Inner Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Inner Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Front Lower Shock absorbers has an excessively worn bush both sides of vehicle (5.3.2 (c)) | 1 |
Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings floor new jacking point |6.1.B.2| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Nearside Rear Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Rear fog lamp not working (1.3.2b) | 1 |
Fuel tank leaking |7.2.3| | 1 |
Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Nearside Front Passenger`s seat insecure |6.2.A.1| | 1 |
Nearside Front Wheel nut|s| missing |4.2.A.1e| | 1 |
Indicator switch faulty |1.4.A.1| | 1 |
Rear Mechanical brake component has restricted free movement | 1 |
Offside Rear wheel cylinder leaking |3.6.A.1| | 1 |
Nearside Subframe mounting prescribed area is excessively corroded outer sill at rear |2.4.A.3| | 1 |
Offside Subframe mounting prescribed area is excessively corroded outer sill at rear |2.4.A.3| | 1 |
Nearside Subframe mounting prescribed area is excessively corroded inner sill at rear |2.4.A.3| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded inner wing rear of headlamp |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded inner wing along top |2.4.A.3| | 1 |
Offside Rear Subframe mounting prescribed area is excessively corroded inner wing close to subframe mounting |2.4.A.3| | 1 |
Nearside Rear Subframe mounting prescribed area is excessively corroded inner wing close to subframe mounting |2.4.A.3| | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Trailing arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Front Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
Exhaust mounting missing |7.1.1b| | 1 |
Nearside Front Shock absorber insecure |2.7.2b| | 1 |
Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Brake pedal anti-slip provision loose |3.3.A.1b| | 1 |
Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
Nearside Front Fluid suspension has no suspension movement |2.4.D.5| | 1 |
Nearside Rear Fluid suspension has no suspension movement |2.4.D.5| | 1 |
Offside Front Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Outer Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Rear Statutory seat belt missing |5.1.1| | 1 |
Front Fluid suspension has no suspension movement |2.4.D.5| | 1 |
Rear Fluid suspension has no suspension movement |2.4.D.5| | 1 |
Offside Rear Sub-frame attachment rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Rear Wheel nut|s| missing |4.2.A.1e| | 1 |
Offside Front Lower Steering locking device missing |2.2.C.1g| | 1 |
Brake hose excessively deteriorated | 1 |
Nearside Front Upper Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
Offside Front Upper Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Outer Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Centre Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Nearside Rear Seat belt retracting mechanism defective |5.2.5b| | 1 |
Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
Centre Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Front Fluid suspension unit totally deflated |2.4.D.1a| | 1 |
Offside Rear brake drum contaminated by brake fluid |3.5.1h| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Front Headlamp not working on main beam |1.7.5a| | 1 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
Offside Rear Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
Towbar component insecure |6.6.1| | 1 |
Nearside Rear wheel bearing rough when rotated |2.6.1| | 1 |
Nearside Rear Sub-frame rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Sub-frame rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
Rear Fuel system component insecure |7.2.1| | 1 |
Offside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Lower Ball joint has excessive play |2.2.B.1f| | 1 |
Fuel system component leaking |7.2.3| | 1 |
Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Nearside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Steering column cracked and unserviceable |2.2.C.1d| | 1 |
Front brake disc in such a condition that it is seriously weakened | 1 |
Nearside Front Side repeater not working |1.4.A.2c| | 1 |
Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
Offside Inner Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Headlamp aim beam image too far to the right |1.6.B4| | 1 |
Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Centre Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Brake master cylinder fluid level below minimum level |3.6.G.1e| | 1 |
Offside Front Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
Offside Front Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt split (5.3.4 (b) (ii)) | 1 |
Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt split (6.1.7 (g) (ii)) | 1 |
Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
Offside Front Headlamp insecure |1.7.3| | 1 |
Offside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
Nearside Front Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
Fuel system component leaking excessively or a risk of fire (6.1.3 (b) (ii)) | 1 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Fluid suspension has no suspension movement |2.4.D.5| | 1 |
Exhaust emits clearly visible black smoke during acceleration |7.3.A.2c| | 1 |
Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Body has a projection caused by corrosion |6.1.C.1| | 1 |
Body has a projection caused by damage |6.1.C.1| | 1 |
Offside Rear Windscreen wiper blade deteriorated |8.2.2| | 1 |
Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering floor |6.1.A.1| | 1 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner wing |6.1.A.1| | 1 |
Driver`s seat insecure bolt loose |6.2.A.1| | 1 |
Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Nearside Front Lower Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Offside Front Lower Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Offside Rear Fuel pipe leaking |7.2.3| | 1 |
Nearside Rear Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Lower Stop lamp not working |1.2.1b| | 1 |
Offside Rear Lower Stop lamp not working |1.2.1b| | 1 |
Horn sounds harsh or grating |1.6.2e| | 1 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Nearside Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
Offside Front Lower Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear Service brake application uneven across the axle |3.7.D.2b| | 1 |
Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Offside Front Side repeater excessively deteriorated so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Nearside Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
Offside Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |