Most common failures | No# failures |
---|
Headlamp aim out of alignment | 4 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 4 |
Windscreen wiper does not clear the windscreen effectively | 3 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Brakes imbalanced across an axle | 2 |
Windscreen washer not working | 2 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 2 |
Nearside Seat belt anchorage prescribed area is excessively corroded floor / inner sill |5.2.6| | 1 |
Fuel tank leaking |7.2.3| | 1 |
Offside Suspension spring mounting prescribed area is excessively corroded sill inner sill |2.4.A.3| | 1 |
Main beam `tell-tale` not working |1.7.4c| | 1 |
Electrical wiring inadequately supported |1.9.2a| | 1 |
Offside Steering rack gaiter split |2.2.D.2d| | 1 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
Registration plate lamp issues | 1 |
Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
Parking brake: efficiency below requirements |3.7.B.7| | 1 |
Front Fuel hose leaking |7.2.3| | 1 |
Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Front Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
Offside Front Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
Offside Outer Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Front Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
Nearside Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
Brake hose excessively deteriorated | 1 |
Rear Electrical wiring damaged, likely to cause a short |1.9.2b| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Rear brake binding | 1 |
Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
Horn not working |1.6.2a| | 1 |
Direction indicators not working |1.4.A.2c| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Horn not working (7.7 (a)) | 1 |
Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Rear Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement d bush |2.4.G.2| | 1 |
Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement d bush |2.4.G.2| | 1 |
Offside Rear Fluid suspension unit inappropriately repaired linkage loose |2.4.A.2| | 1 |
Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 1 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Windscreen wiper missing both (3.4 (a)) | 1 |
Nearside Rear Shock absorbers has a serious fluid leak | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |