Most common failures | No# failures |
---|
Offside Rear fog lamp not working |1.3.2b| | 4 |
Brake pipe excessively corroded | 3 |
Registration plate lamp issues | 3 |
Headlamp aim out of alignment | 3 |
Rear brake application uneven | 2 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Fuel system component leaking |7.2.3| | 2 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Rear fog lamp tell tale not working |1.3.1b| | 2 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
Brakes imbalanced across an axle | 2 |
Nearside Side repeater not working |1.4.A.2c| | 2 |
Speedometer cannot be illuminated. |6.7.3| | 1 |
Front Side repeater not working |1.4.A.2c| | 1 |
Offside Front Direction indicator not working |1.4.A.2c| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Headlamp not working on main beam |1.7.5a| | 1 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Nearside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
Bonnet cannot be secured in the closed position |8.4.1| | 1 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
Rear Rear fog lamp not working |1.3.2b| | 1 |
Horn not working |1.6.2a| | 1 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Rear Stop lamp excessively deteriorated so that it is not visible from a reasonable distance |1.2.1d| | 1 |
Offside Front Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
Nearside Front Steering lock stop incorrectly adjusted |2.2.D.2c| | 1 |
Offside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Front Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Rear Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Nearside Rear brake drum contaminated by oil |3.5.1h| | 1 |
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Nearside Front Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
Horn not working |7.7 |a| |ii|| | 1 |
Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
Offside Rear Parking |secondary brake| on a single line braking system has inadequate effort at a wheel o/s rear showing low effort [on handbrake] |1.3.1 |a| |i|| | 1 |
Brake lever has insufficient reserve travel no reserve travel on handbrake |1.1.2 |a|| | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
Offside Inner Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
Inner Side repeater not working |1.4.A.2c| | 1 |
Offside Side repeater insecure |1.4.A.2b| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Headlamp aim beam image kick up to the offside |1.6.B1| | 1 |
Offside Headlamp aim beam image kick up to the offside |1.6.B1| | 1 |
Offside Rear Anti-roll bar linkage insecure |2.4.G.1| | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Nearside Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
Brake pedal anti-slip provision loose |3.3.A.1b| | 1 |
Nearside brake disc excessively pitted |3.5.1h| | 1 |
Nearside Side repeater incorrect colour |1.4.A.2f| | 1 |
Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |