Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 28 |
Brake pipe excessively corroded | 25 |
Registration plate lamp issues | 22 |
Registration plate issues | 18 |
Headlamp aim out of alignment | 16 |
Exhaust emissions carbon monoxide content excessive (7.3.B.1a) | 14 |
Parking brake: efficiency below requirements (3.7.B.7) | 13 |
Brake hose excessively deteriorated | 9 |
Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 7 |
Rear parking brake recording little or no effort | 6 |
Brakes imbalanced across an axle | 5 |
Offside Stop lamp not working (1.2.1b) | 4 |
Battery insecure (1.9.1) | 4 |
Offside Front position lamp(s) not working (1.1.A.3b) | 4 |
Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 4 |
Nearside Front position lamp(s) not working (1.1.A.3b) | 4 |
Offside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 4 |
Rear Exhaust has part of the system excessively deteriorated (7.1.1a) | 3 |
Nearside Rear Brake hose twisted (3.6.B.4c) | 3 |
Nearside Rear position lamp(s) not working (1.1.A.3b) | 3 |
Anti-lock braking system warning lamp indicates an ABS fault | 3 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 3 |
Rear fog lamp not working (1.3.2b) | 3 |
Rear brake binding | 3 |
Centre Rear Exhaust has a major leak of exhaust gases (7.1.2) | 2 |
Horn not working (7.7 (a)) | 2 |
Nearside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2) | 2 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Offside Rear Rear fog lamp not working (1.3.2b) | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded anti roll bar mounting (2.4.A.3) | 2 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
Power steering pump leaking from a failed component (2.3.3b) | 2 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 2 |
Nearside Headlamp not working on dipped beam (1.7.5a) | 2 |
Nearside Headlamp not working on main beam (1.7.5a) | 2 |
Rear Exhaust system not adequately supported (7.1.1) | 2 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 2 |
Rear Fuel system component leaking (7.2.3) | 2 |
Exhaust engine idle speed too high (7.3.A.2a) | 2 |
Rear Exhaust has a major leak of exhaust gases (7.1.2) | 2 |
Offside Front Track rod end ball joint has excessive play (2.2.B.1f) | 2 |
Exhaust emissions hydrocarbon content excessive (7.3.B.1b) | 2 |
Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 2 |
Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 2 |
Rear fog lamp tell tale not working (1.3.1b) | 2 |
Nearside Side repeater not working (1.4.A.2c) | 2 |
Offside Rear Fluid suspension pipe leaking (2.4.D.2) | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 2 |
Nearside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 2 |
Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Rear brake application uneven | 2 |
Nearside Front Headlamp not working on main beam (1.7.5a) | 2 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
Offside Indicator tell tale inoperative (1.4.A.2a) | 1 |
Rear Exhaust mounting missing (7.1.1b) | 1 |
Offside Rear Stop lamp not working (1.2.1b) | 1 |
Centre Rear Exhaust system not adequately supported (7.1.1) | 1 |
Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Rear Fuel pipe leaking (6.1.3 (b) (i)) | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Front Brake disc significantly and obviously worn both front (1.1.14 (a) (i)) | 1 |
Power steering component(s) leaking (2.3.3b) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced frame mounting (6.1.1 (c) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced frame mount (6.1.1 (c) (i)) | 1 |
Nearside Front Headlamp not working on dipped beam (1.7.5a) | 1 |
Offside Rear Front wheel bearing has excessive play (2.5.A.3c) | 1 |
Parking brake lever has no reserve travel (3.1.6b) | 1 |
Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Side repeater missing |1.4.A.2b| | 1 |
Front brake disc in such a condition that it is seriously weakened | 1 |
Parking brake lever ratchet not holding correctly (1.1.6 (a)) | 1 |
Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4) | 1 |
Nearside Front Lower Suspension arm has excessive play in a pin/bush rear (2.4.G.2) | 1 |
Nearside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced (2.4.G.1) | 1 |
Offside Rear Shock absorber has a serious fluid leak (2.7.3) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill - next to subframe mounting (5.3.6 (a) (i)) | 1 |
Drivers seat backrest cannot be secured in the upright position. (6.2.5 (b) (ii)) | 1 |
Passengers seat backrest cannot be secured in the upright position. (6.2.6 (a) (i)) | 1 |
Nearside Front Direction indicator incomplete (1.5.A1b) | 1 |
Nearside Front Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
Offside Front Inner Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Oil leaking excessively from engine engine (8.4.1 (a) (i)) | 1 |
Emissions not tested engine over heating cooling loss (8.2.1.2 (d)) | 1 |
Headlamp levelling device inoperative both lamps (4.1.5 (a)) | 1 |
Emissions not tested Exhaust blowing (8.2.1.2 (d)) | 1 |
Emissions not tested (7.0) | 1 |
Offside Front coil spring broken (2.4.C.1a) | 1 |
Rear Exhaust system not adequately supported HANGERS BROKEN (7.1.1) | 1 |
Offside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Rear Exhaust system not adequately supported (7.1.1) | 1 |
Nearside Front Inner Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch (2.4.A.3) | 1 |
Nearside front brake grabbing severely (3.7.A.2b) | 1 |
Nearside Front Battery insecure (1.9.1) | 1 |
Nearside Rear Wheel bolt(s) missing (4.2.A.1e) | 1 |
Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Rear Exhaust emissions carbon monoxide content excessive (7.3.B.1a) | 1 |
Nearside Rear Shock absorber has a serious fluid leak (2.7.3) | 1 |
Nearside Steering pivot point has excessive play idler (2.2.B.1g) | 1 |
Anti-lock braking system warning lamp does not illuminate (3.4.1b) | 1 |
Drivers door does not latch securely closed (6.2.B.1a) | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded 2 areas (2.4.A.3) | 1 |
Nearside Front Outer Track rod end ball joint has excessive play (2.2.B.1f) | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing at lower susp mount (2.4.A.3) | 1 |
Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
Offside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
Offside Front brake caliper has restricted free movement |3.5.1k| | 1 |
Fuel cap/sealing device sealing washer deteriorated (7.2.4c) | 1 |
Nearside Front Headlamp not in good working order (not working) (1.2.4a) | 1 |
Nearside Exhaust mounting missing (7.1.1b) | 1 |
Rear Exhaust system not adequately supported all back mounts missing and broken (7.1.1) | 1 |
Rear Statutory seat belt missing (5.1.1) | 1 |
Steering pivot point has excessive play (2.2.B.1g) | 1 |
Nearside Front Shock absorber has a serious fluid leak (2.7.3) | 1 |
Offside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2) | 1 |
Nearside Rear Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
Offside Rear Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
Offside Front Shock absorber has a serious fluid leak (2.7.3) | 1 |
Front Exhaust system not adequately supported (7.1.1) | 1 |
Offside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
Offside Rear fog lamp not working |1.3.2b| | 1 |
Service brake: efficiency below requirements (3.7.B.7) | 1 |
Offside Front Steering component mounting prescribed area is excessively corroded chassis at tie rod mounting point (as chalked) (2.1.2 (e) (i)) | 1 |
Nearside Front Steering component mounting prescribed area is excessively corroded tie rod mounting point (as chalked) (2.1.2 (e) (i)) | 1 |
Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2) | 1 |
Steering arm has relative movement at its fixings (2.2.B.1h) | 1 |
Offside Front Suspension arm has excessive play in a ball joint (2.4.G.2) | 1 |
Nearside Front Side repeater insecure (1.4.A.2b) | 1 |
Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
Exhaust has part of the system excessively deteriorated (7.1.1a) | 1 |
Offside Rear position lamp(s) not working (1.1.A.3b) | 1 |
Brake fluid contaminated (1.8 (a)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch box section corroded within 30cm of rear spring and axle (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt outer (2.1.3 (g) (ii)) | 1 |
Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Obligatory mirror seriously damaged, affecting the rear view (8.1.2a) | 1 |
Front passenger door cannot be opened from inside the vehicle (6.2.B.1b) | 1 |
Offside Power steering pump leaking from a failed component (2.3.3b) | 1 |
Rear Fuel pipe leaking (7.2.3) | 1 |
Offside Front Lower Suspension arm has excessive play in a ball joint (2.4.G.2) | 1 |
Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
Rear Shock absorber has an excessively worn bush (2.7.4) | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
Offside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Offside Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Nearside Outer Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Nearside Inner Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Offside Inner Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Offside Outer Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Offside Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
Horn not working |1.6.2a| | 1 |
Headlamp aim projected beam image is obviously incorrect nearside and offside (4.1.2 (c)) | 1 |
Front Drag link end ball joint has excessive play nearside and offside (2.1.3 (b) (i)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mount area (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mount area (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis outer face (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower - front of wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
Nearside Rear Stop lamp not working (1.2.1b) | 1 |
Centre Exhaust mounting missing (7.1.1b) | 1 |
Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner wing/ chassis (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner wing / chassis (5.3.6 (a) (i)) | 1 |
Nearside Side repeater missing (4.4.1 (a) (ii)) | 1 |
Offside Side repeater missing (4.4.1 (a) (ii)) | 1 |
Hazard warning lamps inoperative all (4.4.1 (e)) | 1 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Windscreen washer not working | 1 |
Nearside Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
Offside Front Brake hose bulging under pressure (3.6.B.3) | 1 |
Offside Rear Fuel hose leaking (7.2.3) | 1 |
Nearside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
Offside Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
Nearside Rear Body has a sharp edge caused by corrosion (6.1.C.1) | 1 |
Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting point (5.3.6 (a) (i)) | 1 |
Offside Track rod end ball joint has excessive play (2.2.B.1f) | 1 |
Front brake excessively fluctuating | 1 |
Nearside Front Position lamp not working (4.2.1 (a)) | 1 |
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg as marked (5.3.6 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg as marked (5.3.6 (a) (i)) | 1 |
Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg as marked (5.3.6 (a) (i)) | 1 |
Offside Front Side repeater not working (1.4.A.2c) | 1 |
Front Windscreen in an unacceptable condition (3.2 (c) (i)) | 1 |
Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
Nearside Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
Front Steering damper leaking oil (2.2.C.1f) | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
Offside Front Drivers door cannot be opened from inside the vehicle (6.2.B.1b) | 1 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
Exhaust mounting missing (7.1.1b) | 1 |
Offside Front front brake binding (3.7.B.1) | 1 |
Nearside Rear brake disc excessively pitted (3.5.1h) | 1 |
Offside Rear brake disc excessively pitted (3.5.1h) | 1 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
Offside Rear Body panel damaged and likely to cause injury wheel arch damaged (6.2.1 (a) (i)) | 1 |
Offside Rear Rear fog lamp emits a light other than red (1.3.2e) | 1 |
Steering column will not lock in a fixed position |adjustable type| |2.1.2a| | 1 |
Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Rear Drive shaft flexible coupling so deteriorated it is likely to fail (6.1.7 (d) (ii)) | 1 |
Offside Front Engine mounting damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
Offside Front Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a) | 1 |
Nearside Rear Brake hose excessively damaged (3.6.B.4d) | 1 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg large hole (5.3.6 (a) (i)) | 1 |
Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension mounting point large hole (5.3.6 (a) (i)) | 1 |
Nearside Windscreen wiper blade missing (8.2.2) | 1 |
Offside Front Outer Track rod end ball joint has excessive play (2.2.B.1f) | 1 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Fuel system component leaking fuel filter (7.2.3) | 1 |
Nearside Stop lamp not working (1.2.1b) | 1 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3) | 1 |
Nearside Rear Direction indicators incorrect colour (1.4.A.2f) | 1 |
Offside Rear Direction indicators incorrect colour (1.4.A.2f) | 1 |
Offside Rear fog lamp not working (1.3.2b) | 1 |
Nearside Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength (2.4.A.3) | 1 |
Centre Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
Nearside Rear position lamp(s) excessively deteriorated so that it is not visible from a reasonable distance (1.1.A.3d) | 1 |
Nearside Rear Exhaust has a part missing (7.1.1a) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Headlamp not working on dipped beam (1.7.5a) | 1 |
Offside Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Inner Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt Both traction arms (5.3.4 (b) (ii)) | 1 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Emissions not tested Engine misfire (8.2.1.2 (d)) | 1 |
Headlamp switch faulty |1.7.1| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Rear fog lamp tell tale not working |1.3.1b| | 1 |
Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
Nearside Front Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
Rear Fuel system component leaking |7.2.3| | 1 |
Power steering ram(s) leaking from a failed component (2.3.3b) | 1 |
Fuel system component leaking rear fuel pump (7.2.3) | 1 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
Offside Rear rear brake recording little or no effort (3.7.B.5a) | 1 |
Offside Front Side repeater insecure (1.4.A.2b) | 1 |
Nearside Front All position lamps not working (4.2.1 (a)) | 1 |
Nearside Front Vehicle structure has a fracture which is likely to adversely affect braking or steering (6.1.1 (a) (ii)) | 1 |
Offside Front Vehicle structure has a fracture which is likely to adversely affect braking or steering (6.1.1 (a) (ii)) | 1 |
Nearside Front Headlamp adversely affected by the operation of another lamp (1.7.5c) | 1 |
Centre Exhaust system not adequately supported (7.1.1) | 1 |
Steering system has excessive free play detected at the steering wheel (steering box fitted) (2.2.A.1a) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength track control arm mounting (5.3.6 (a) (i)) | 1 |
Nearside Front coil spring broken (2.4.C.1a) | 1 |
Braking system leaking (3.6.A.1) | 1 |
Offside Rear rear brake excessively fluctuating (3.7.B.3) | 1 |
Front brake application uneven | 1 |
Nearside Front Lower Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Nearside Front Upper Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Nearside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Offside Front Upper Suspension arm has excessive play in a ball joint (2.4.G.2) | 1 |
Parking brake lever defective so that it cannot be satisfactorily operated (1.1.6 (d)) | 1 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Front Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
Front Exhaust has part of the system excessively deteriorated (7.1.1a) | 1 |
Nearside Rear coil spring corroded so that its cross sectional area is reduced and seriously weakened (2.4.C.1b) | 1 |
Nearside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
Horn not working (1.6.2a) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside front brake binding (3.7.B.1) | 1 |
rear brakes release unevenly (3.7.B.4) | 1 |
Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
Offside Front Direction indicators not working (1.4.A.2c) | 1 |
Offside Headlamp not working on main beam (1.7.5a) | 1 |