| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 40 |
| Windscreen wiper does not clear the windscreen effectively | 37 |
| Brake pipe excessively corroded | 30 |
| Brake hose excessively deteriorated | 22 |
| Brakes imbalanced across an axle | 21 |
| Registration plate lamp issues | 16 |
| Parking brake: efficiency below requirements (3.7.B.7) | 13 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 11 |
| Registration plate issues | 11 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 11 |
| Offside front brake binding (3.7.B.1) | 10 |
| Rear brake binding | 9 |
| Exhaust emissions carbon monoxide content excessive (7.3.B.1a) | 9 |
| Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 8 |
| Offside Front position lamp(s) not working (1.1.A.3b) | 8 |
| Battery insecure (1.9.1) | 8 |
| Rear parking brake recording little or no effort | 8 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 7 |
| Hazard warning switch faulty (1.4.B.1d) | 6 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 6 |
| Steering system has excessive free play detected at the steering wheel (steering box fitted) (2.2.A.1a) | 6 |
| Nearside Stop lamp not working (1.2.1b) | 6 |
| Offside Stop lamp not working (1.2.1b) | 6 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 5 |
| Exhaust has a major leak of exhaust gases (7.1.2) | 5 |
| Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 5 |
| Front Exhaust has a major leak of exhaust gases (7.1.2) | 5 |
| Nearside Front wheel bearing rough when rotated (2.5.A.2) | 5 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 5 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 4 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 4 |
| Nearside Rear position lamp(s) excessively deteriorated so that it is not visible from a reasonable distance (1.1.A.3d) | 4 |
| Nearside Rear position lamp(s) not working (1.1.A.3b) | 4 |
| Nearside Front Front position lamp(s) not working (1.1.A.3b) | 4 |
| Fuel pipe leaking (7.2.3) | 4 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Exhaust mounting missing (7.1.1b) | 4 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 4 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
| Offside Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 4 |
| Offside Rear fog lamp not working (1.3.2b) | 4 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 3 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 3 |
| Offside Rear Sub-frame rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 3 |
| Front brake application uneven | 3 |
| Rear Exhaust system not adequately supported (7.1.1) | 3 |
| Offside Rear Stop lamp not working (1.2.1b) | 3 |
| Nearside Front position lamp(s) not working (1.1.A.3b) | 3 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Hazard warning lamps inoperative (1.4.B.1b) | 3 |
| Nearside Front front brake binding (3.7.B.1) | 3 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3) | 3 |
| Rear Exhaust has a major leak of exhaust gases (7.1.2) | 3 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2) | 3 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Nearside Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 3 |
| All direction indicators not working (4.4.1 (a) (ii)) | 3 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Steering box has relative movement between sector shaft and the drop arm (2.2.B.1b) | 3 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Nearside Headlamp not in good working order adversely affecting beam image (1.2.4a) | 3 |
| Offside Rear Body has a sharp edge caused by corrosion (6.1.C.1) | 3 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Offside Headlamp not working on dipped beam (1.7.5a) | 3 |
| Offside Front Track rod end ball joint has excessive play (2.2.B.1f) | 3 |
| Offside Outer Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 3 |
| Hazard warning lamps not flashing in phase, with ignition on (1.4.B.1f) | 3 |
| Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f) | 3 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Front Track rod end ball joint has excessive play (2.2.B.1f) | 3 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 2 |
| Exhaust system not adequately supported (7.1.1) | 2 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 2 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 2 |
| Offside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 2 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 2 |
| Offside Front coil spring broken (2.4.C.1a) | 2 |
| Offside Rear Shock absorber has a serious fluid leak (2.7.3) | 2 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3) | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a) | 2 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill (2.4.A.3) | 2 |
| Nearside Front Direction indicator not working (1.4.A.2c) | 2 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 2 |
| Nearside Headlamp not working on main beam (1.7.5a) | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 2 |
| Nearside Rear Position lamp not working (4.2.1 (a)) | 2 |
| Nearside Front Suspension arm has excessive play in a ball joint (2.4.G.2) | 2 |
| Central Rear Seat belt missing (7.1.2 (a)) | 2 |
| Offside Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 2 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 2 |
| Nearside Rear Exhaust system not adequately supported (7.1.1) | 2 |
| Offside Front wheel bearing rough when rotated (2.5.A.2) | 2 |
| Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 2 |
| Centre Exhaust system not adequately supported (7.1.1) | 2 |
| Fuel system component leaking fuel filter (6.1.3 (b) (i)) | 2 |
| Offside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 2 |
| Emissions not tested (7.0) | 2 |
| Nearside Front Body has a sharp edge caused by corrosion (6.1.C.1) | 2 |
| Nearside Rear Stop lamp not working (1.2.1b) | 2 |
| Horn not working (7.7 (a)) | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 2 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 2 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Headlamp aim beam image obviously incorrect (1.8.A.1b) | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 2 |
| Rear fog lamp tell tale not working (1.3.1b) | 2 |
| Nearside front brake binding (3.7.B.1) | 2 |
| Nearside Rear Outer Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.4.G.4e) | 2 |
| Offside Headlamp not working on main beam (1.7.5a) | 2 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint (2.4.G.2) | 2 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Centre Exhaust has a major leak of exhaust gases (7.1.2) | 2 |
| Offside Rear Rear fog lamp not working (1.3.2b) | 2 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Fuel system component leaking (7.2.3) | 2 |
| Direction indicators flashing less than 60 times a minute (1.4.A.2g) | 2 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Nearside Rear Boot lid likely to become detached hole by hindge in roof (6.2.1 (a) (ii)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Rear Brake load sensing valve linkage defective and function impaired (1.1.17 (a)) | 1 |
| Offside Brake linkage excessively corroded rusted out of floor (1.1.15 (b)) | 1 |
| Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Windscreen wiper not operating automatically when switched on (8.2.1b) | 1 |
| Nearside Front Drag link end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Front Drag link end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Brake load sensing valve linkage defective and function impaired (3.6.E.3) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
| Speedometer cannot be illuminated. (6.7.3) | 1 |
| Nearside Rear passenger door cannot be opened from outside the vehicle (6.2.B.1c) | 1 |
| Suspension component mounting prescribed area is excessively corroded o/s rear floor (2.4.A.3) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded chassis (2.4.A.3) | 1 |
| Fuel cap/sealing device sealing washer torn (7.2.4c) | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded o/s front bulkhead, by bonnet hinge (3.6.C.3) | 1 |
| Suspension component mounting prescribed area is excessively corroded n/s rear outer sill (2.4.A.3) | 1 |
| Seat belt anchorage prescribed area is excessively corroded o/s floor joining sill (5.2.6) | 1 |
| Nearside Headlamp not in good working order (not working) (1.2.4a) | 1 |
| Offside Headlamp not in good working order (not working) (1.2.4a) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded arch (2.4.A.3) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded arch (2.4.A.3) | 1 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Nearside Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Windscreen has damage | 1 |
| front brake juddering severely (3.7.A.2b) | 1 |
| Nearside Rear Service brake grabbing severely (1.2.1 (c)) | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion (6.1.C.1) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.A.1) | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Nearside Rear Valve stem seriously misaligned (4.1.D.1e) | 1 |
| Nearside Headlamp not working on dipped beam (1.7.5a) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill and floorpan (6.1.B.2) | 1 |
| Steering box insecure (2.2.B.1a) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users fuel pump (8.4.1 (a) (i)) | 1 |
| Nearside Exhaust emissions carbon monoxide content excessive (7.3.B.1a) | 1 |
| Nearside Rear Exhaust system not adequately supported silencer mounting rubber missing (7.1.1) | 1 |
| Offside Rear Fuel system component leaking fuel pump leaking (7.2.3) | 1 |
| Offside Rear position lamp(s) adversely affected by the operation of another lamp (1.1.A.3f) | 1 |
| Offside Rear front brake binding (3.7.B.1) | 1 |
| Front Power steering pipe(s) or hose(s) fouling other parts of the vehicle (2.3.2) | 1 |
| Offside rear brake excessively fluctuating (3.7.B.3) | 1 |
| Nearside Rear Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.4.G.4e) | 1 |
| Offside Front Headlamp not working on dipped beam (1.7.5a) | 1 |
| Nearside Front Steering arm has relative movement at its fixings (2.2.B.1h) | 1 |
| front brake binding (3.7.B.1) | 1 |
| Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Nearside Windscreen wiper missing (3.4 (a)) | 1 |
| Offside Windscreen wiper missing (3.4 (a)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Spring mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a) | 1 |
| Nearside Front All position lamps not working (1.1.A.3b) | 1 |
| coil spring incomplete (2.4.C.1a) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill and inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel arch area (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor pan (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch area (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail area (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced x2 (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing beside front anti roll bar (2.4.A.3) | 1 |
| Nearside Front Front suspension has excessive play in a upper suspension ball joint (2.5.B.1a) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Drivers seat moving inadvertently (6.2.5 (b) (ii)) | 1 |
| Suspension component mounting prescribed area is excessively corroded all under vehicle areas carroded (2.4.A.3) | 1 |
| Nearside Inner Front Lower Suspension spring mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Offside Inner Rear Lower Subframe mounting prescribed area is deliberately modified which significantly reduces the original strength (2.4.A.3) | 1 |
| Offside Rear Lower Subframe mounting prescribed area is deliberately modified which significantly reduces the original strength (2.4.A.3) | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Offside Front Lower Steering component mounting prescribed area is excessively corroded (2.2.C.1h) | 1 |
| Nearside Rear Exhaust mounting missing (7.1.1b) | 1 |
| Offside Rear Exhaust mounting missing (7.1.1b) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear fog lamp not working (1.3.2b) | 1 |
| Offside Front front brake binding (3.7.B.1) | 1 |
| Centre Steering damper leaking oil (2.2.C.1f) | 1 |
| Power steering component(s) leaking (2.3.3b) | 1 |
| Rear brake disc excessively pitted (3.5.1h) | 1 |
| Power steering pipe(s) or hose(s) leaking from a joint (2.3.3b) | 1 |
| Nearside Front Headlamp excessively damaged so that the light output is severely reduced (1.7.5a) | 1 |
| Offside Front Headlamp excessively damaged so that the light output is severely reduced (1.7.5a) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
| Nearside Rear Sub-frame synthetic bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Offside Rear Sub-frame synthetic bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Front All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Fuel hose damaged (6.1.3 (c) (ii)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Offside rear brake juddering severely (3.7.A.5b) | 1 |
| Offside rear brake grabbing severely (3.7.A.5b) | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch has hole in it near suspension arm (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rust hole in sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Steering pivot point has excessive play (2.2.B.1g) | 1 |
| Nearside Front coil spring incomplete (2.4.C.1a) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under bonnet (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Nearside Rear Exhaust silencer insecure system box (8.1.1 (b) (i)) | 1 |
| Rear Body panel corroded and likely to cause injury body panel (6.2.1 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected body sill (5.3.6 (a) (ii)) | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill (2.4.A.3) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch (2.4.A.3) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch (2.4.A.3) | 1 |
| Rear Exhaust system not adequately supported x4 rubber splitting (7.1.1) | 1 |
| Nearside Front Lower Fuel pipe leaking metal fuel pipes heavily corroded and leaking (7.2.3) | 1 |
| Rear Exhaust system not adequately supported rubber exhaust support rubber split to excess x4 (7.1.1) | 1 |
| Horn sound not in accordance with requirements (7.7 (c)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength tie bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen (4.1.2 (a)) | 1 |
| Steering box leaking to the extent that oil is dripping (2.1.1 (e) (ii)) | 1 |
| Offside Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor pan area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength in rear wheel arch (5.3.6 (a) (i)) | 1 |
| Rear Fuel pipe union leaking (6.1.3 (b) (i)) | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Nearside Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 1 |
| Nearside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Nearside Rear Sub-frame rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Nearside Front Lower Radius arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Front coil spring fractured (2.4.C.1a) | 1 |
| Offside Headlamp aim aimed so that it dazzles other road users (1.8.A.1a) | 1 |
| Offside Front Headlamp aim aimed so that it dazzles other road users (1.8.A.1a) | 1 |
| Offside Front Headlamp insecure (1.7.3) | 1 |
| Fuel pipe union leaking (6.1.3 (b) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Steering box has a significant oil leak (2.2.D.2e) | 1 |
| Rear fog lamp switch faulty (1.3.1a) | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded outer sill (5.2.6) | 1 |
| Nearside Front wheel bearing has excessive play (2.5.A.3c) | 1 |
| Braking system leaking (3.6.A.1) | 1 |
| Brake pedal creeps down while the pedal is held under pressure (3.3.B.1a) | 1 |
| Nearside Steering lock stop missing (2.2.D.2c) | 1 |
| Offside Steering lock stop missing (2.2.D.2c) | 1 |
| Offside rear brake recording little or no effort (3.7.B.5a) | 1 |
| Centre Rear Statutory seat belt missing (5.1.1) | 1 |
| Offside Front Body has a projection caused by damage (6.1.C.1) | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone A (8.3.1e) | 1 |
| Offside Front Direction indicator not working (1.4.A.2c) | 1 |
| Rear Exhaust mounting missing (7.1.1b) | 1 |
| Centre Exhaust mounting missing (7.1.1b) | 1 |
| Offside Rear brake caliper has restricted free movement (3.5.1k) | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
| Offside Outer Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Parking brake lever has no reserve travel (3.1.6b) | 1 |
| Nearside Front Steering pivot point has excessive play (2.2.B.1g) | 1 |
| Nearside Front Headlamp not working on dipped beam (1.7.5a) | 1 |
| Offside Front Upper Suspension spring mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Front Track rod end damaged and unserviceable (2.2.C.1d) | 1 |
| Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Offside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Nearside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Horn not working (1.6.2a) | 1 |
| Central Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Nearside Front Lower Intermediate drop arm insecure (2.1.3 (a) (i)) | 1 |
| Nearside Front Lower Fuel pipe leaking excessively or a risk of fire (6.1.3 (b) (ii)) | 1 |
| Central Front Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Offside Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting center (6.2.2 (d) (i)) | 1 |
| Nearside Rear Brake cable has restricted free movement (1.1.15 (e)) | 1 |
| Offside Front Outer Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Parking brake is not capable of being maintained in operation by direct mechanical action only (3.1.2) | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion on the arch (6.1.C.1) | 1 |
| Offside Rear Upper Body has a sharp edge caused by corrosion upper and lower of rear quarter panel (6.1.C.1) | 1 |
| Offside Front Body has a sharp edge caused by corrosion lower bumper (6.1.C.1) | 1 |
| Offside Front Lower Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Nearside Front Inner Track rod end ball joint has excessive play (2.2.B.1f) | 1 |
| Offside Front Outer Track rod end ball joint has excessive play (2.2.B.1f) | 1 |
| Steering arm has relative movement at its fixings Steering idler arm has excessive movement (2.2.B.1h) | 1 |
| Nearside Front Headlamp not working on main beam (1.7.5a) | 1 |
| Offside Front Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Front Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Front Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Rear Lower Body has a sharp edge caused by corrosion wheel arch (6.1.C.1) | 1 |
| Offside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Chase jack point (6.1.B.2) | 1 |
| Nearside Front Shock absorber has a serious fluid leak (2.7.3) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Rear Anti-roll bar has excessive play in a ball joint (2.4.G.2) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Centre Rear Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (7.1.4) | 1 |
| Offside Rear Fuel pipe leaking (6.1.3 (b) (i)) | 1 |
| Subframe mounting prescribed area is excessively corroded both side rear (2.4.A.3) | 1 |
| Nearside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion wheelarch (6.1.C.1) | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Exhaust has a part missing (7.1.1a) | 1 |
| Offside Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Offside Outer Front Track rod end ball joint has excessive play (2.2.B.1f) | 1 |
| Front Body insecure Grille (6.2.2 (a) (i)) | 1 |
| Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
| Offside Rear Seat belt buckle missing (7.1.2 (d)) | 1 |
| Nearside Rear Seat belt buckle missing (7.1.2 (d)) | 1 |
| Nearside Headlamp insecure (4.1.1 (c)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect Both sides (4.1.2 (c)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill corroded front and rear (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Drive shaft joint excessively worn (6.1.7 (c) (i)) | 1 |
| Offside Rear Suspension unit leaking (5.3.5 (c)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt Both sides inner and outer (2.1.3 (g) (ii)) | 1 |
| Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Centre Exhaust has part of the system excessively deteriorated (7.1.1a) | 1 |
| Fuel pipe leaking from pump (porous) (6.1.3 (b) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced footwell holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear position lamp(s) incorrect colour (1.1.A.3e) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded anti roll bar (2.4.A.3) | 1 |
| Service brake: efficiency below requirements (3.7.B.7) | 1 |
| Offside Rear position lamp(s) not working (1.1.A.3b) | 1 |
| Stop lamp remains on when the brakes are released | 1 |
| Offside Rear Inner Drive shaft which forms part of the suspension coupling gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.4.G.4e) | 1 |
| Offside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
| Nearside Headlamp not in a clean condition affecting beam image (1.2.4a) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Corrosion hole in rear sill within prescribed area (5.3.6 (a) (i)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint (2.5.B.1a) | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Exhaust emissions hydrocarbon content excessive (7.3.B.1b) | 1 |
| Rear brake application uneven | 1 |
| Offside Rear An item not tested (Manual) | 1 |
| Nearside Rear coil spring incomplete (2.4.C.1a) | 1 |
| Nearside Rear Suspension arm has excessive play in a pin/bush (2.4.G.2) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill (6.1.B.2) | 1 |
| Offside Rear fog lamp excessively damaged so that it is not visible from a reasonable distance (1.3.2d) | 1 |
| Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Offside Position lamp not working (4.2.1 (a)) | 1 |
| Nearside Position lamp adversely affected by the operation of another lamp Not working unless headlamp is on (4.2.3 (c)) | 1 |
| Nearside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced coil spring and wishbone mount (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced coil spring and wishbone mount (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Front Body component corroded and likely to cause injury valance (6.2.1 (a) (i)) | 1 |
| Nearside Rear Shock absorber has negligible damping effect (2.7.5) | 1 |
| Offside Rear Shock absorber has negligible damping effect (2.7.5) | 1 |
| Nearside Rear Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Headlamp aim not tested (4.1.2 (b)) | 1 |
| Front Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Parking (secondary brake) on a single line braking system has inadequate effort at a wheel both sides (1.3.1 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover missing (2.4.G.2) | 1 |
| Offside Front Suspension arm ball joint dust cover missing (2.4.G.2) | 1 |
| Offside Rear Body has a sharp edge caused by damage (6.1.C.1) | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Nearside Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced (1.7.5a) | 1 |
| Centre Front Braking system leaking (3.6.A.1) | 1 |
| Nearside Front Windscreen wiper blade deteriorated (8.2.2) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Front Exhaust has a major leak of exhaust gases pipe (6.1.2 (a)) | 1 |
| Rear Exhaust has a major leak of exhaust gases box missing (6.1.2 (a)) | 1 |
| Nearside Rear Fuel pipe leaking by rear suspension arm (6.1.3 (b) (i)) | 1 |
| Nearside Front Seat belt not functioning as intended catch. (7.1.2 (c)) | 1 |
| Windscreen washer not working | 1 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill @ drain hole (5.2.6) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded area around anti-roll bar mounting (2.4.A.3) | 1 |
| Nearside Rear Brake hose twisted (3.6.B.4c) | 1 |
| Offside Rear Brake hose twisted (3.6.B.4c) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Outerr sill (5.2.6) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner body sill (6.1.1 (c) (i)) | 1 |
| Offside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Rear Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt split (6.1.7 (g) (ii)) | 1 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside Front Body panel corroded and likely to cause injury arch corroded/holed (6.2.1 (a) (i)) | 1 |
| Offside Front Body panel corroded and likely to cause injury arch corroded/holed (6.2.1 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases pipe split and blowing (6.1.2 (a)) | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Fuel system component leaking pump (6.1.3 (b) (i)) | 1 |
| Offside Rear Sub-frame pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Front Front wheel bearing has excessive play (2.5.A.3c) | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Nearside Direction indicators not working (1.4.A.2c) | 1 |
| Nearside Rear Rear position lamp(s) not working (1.1.A.3b) | 1 |
| Rear Rear fog lamp not working (1.3.2b) | 1 |
| Offside Direction indicators not working (1.4.A.2c) | 1 |
| Offside Rear Rear position lamp(s) not working (1.1.A.3b) | 1 |
| Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1 |
| Nearside Rear Fuel pipe excessively damaged (7.2.2) | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Offside Sub-frame rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Offside Front Front wheel bearing rough when rotated (2.5.A.2) | 1 |
| Central Rear Fuel system component leaking (6.1.3 (b) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Nearside Rear Body component damaged and likely to cause injury bumper end missing (6.2.1 (a) (i)) | 1 |
| Offside Front Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Offside Rear Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Rear Fuel hose leaking excessively or a risk of fire (6.1.3 (b) (ii)) | 1 |
| Offside Floor excessively deteriorated (6.2.4 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Statutory seat belt missing Buckle (5.1.1) | 1 |
| Centre Rear Seat belt locking mechanism does not secure or release (5.2.5a) | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded Front mount (2.4.A.3) | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded Front mount (2.4.A.3) | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2) | 1 |
| Offside Front Body has a sharp edge caused by corrosion (6.1.C.1) | 1 |
| Rear Service brake effort inadequate at a wheel both sides (1.2.1 (a) (i)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Front Floor excessively deteriorated (6.2.4 (a) (i)) | 1 |
| Offside Front Floor excessively deteriorated (6.2.4 (a) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Front Position lamp not working x2 (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER SILL NR SEAT BELT MOUNTING (6.1.B.2) | 1 |
| Nearside Front Headlamp not working on dipped beam WORKS SOMETIMES (1.7.5a) | 1 |
| Offside Rear Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Nearside Front Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Fuel system component leaking (6.1.3 (b) (i)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Offside Rear Brake hose excessively twisted (1.1.12 (b) (ii)) | 1 |
| Offside Rear Vehicle structure is fractured and structural rigidity is significantly reduced jacking point (6.1.1 (a) (i)) | 1 |
| Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced seal (6.1.1 (c) (i)) | 1 |
| Offside Rear coil spring broken (2.4.C.1a) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Brake performance unable to be tested (1.2.1 (g)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Headlamp not working on main beam (1.7.5a) | 1 |
| Offside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Nearside Front Steering locking device insecure (2.2.C.1g) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill, next to rear subframe mount marked with chalk (5.3.6 (a) (i)) | 1 |
| Position lamp not working NSF & OSF (4.2.1 (a) (ii)) | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases at both flexi joints (6.1.2 (a)) | 1 |
| Seat belt missing NSR, OSR & CENTRE (7.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength coilspring lower mounting plate (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed due to major leak at flexi joints (8.2.1.2 (d)) | 1 |
| Nearside Front Brake hose twisted (found during steering lock to lock check) (2.2.D.2b) | 1 |
| Nearside Front Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Nearside Rear Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| All direction indicators not working hazard not working not part of test (4.4.1 (a) (ii)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Rear Exhaust has a major leak of exhaust gases back box exhaust (6.1.2 (a)) | 1 |
| Fuel system component leaking leaking from the fuel filter (6.1.3 (b) (i)) | 1 |
| Emissions unable to be completed (8.2.2.2 (e)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Brake hose bulging under pressure (1.1.12 (d)) | 1 |
| Front Windscreen wiper not operating automatically when switched on (8.2.1b) | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.A.1) | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Emissions unable to be completed engine cutting out (8.2.1.2 (d)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill behind wheel marked (6.1.1 (c) (i)) | 1 |
| Rear Fuel system component leaking excessively or a risk of fire (6.1.3 (b) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor (7.1.1 (a) (i)) | 1 |