| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 17 |
| Windscreen wiper does not clear the windscreen effectively | 12 |
| Parking brake: efficiency below requirements |3.7.B.7| | 10 |
| Anti-lock braking system warning lamp indicates an ABS fault | 8 |
| Registration plate lamp issues | 7 |
| Rear parking brake recording little or no effort | 5 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 5 |
| Brake pipe excessively corroded | 5 |
| Registration plate issues | 4 |
| Exhaust engine idle speed too high |7.3.A.2a| | 4 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 4 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Rear fog lamp not working |1.3.2b| | 3 |
| Rear fog lamp not working |1.3.2b| | 3 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside front brake binding |3.7.B.1| | 3 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 3 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 3 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Horn not working |1.6.2a| | 2 |
| Offside Front front brake binding |3.7.B.1| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Rear Exhaust system not adequately supported |7.1.1| | 2 |
| Exhaust system not adequately supported |7.1.1| | 2 |
| Offside Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Brake pedal spongy |3.3.B.1b| | 2 |
| Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Direction indicators not working |1.4.A.2c| | 2 |
| Front brake excessively fluctuating | 2 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Rear Fuel system component leaking |7.2.3| | 2 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Nearside Front Lower Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Nearside Rear brake disc excessively pitted |3.5.1h| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Exhaust mounting missing |7.1.1b| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
| Nearside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Outer Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Steering box damaged and unserviceable |2.2.C.1d| | 1 |
| Nearside Intermediate drop arm damaged and unserviceable |2.2.C.1d| | 1 |
| Offside Intermediate drop arm damaged and unserviceable |2.2.C.1d| | 1 |
| Offside Front coil spring fractured |2.4.C.1a| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Rear Fuel pipe leaking |7.2.3| | 1 |
| Offside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Direction indicators not working |1.4.A.2c| | 1 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Headlamp aim not tested |1.8.A.1c| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Offside Front Braking system leaking |3.6.A.1| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Rear brake binding | 1 |
| Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Windscreen washer not working | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Position lamp lens seriously defective (4.2.1 (b)) | 1 |
| Rear Position lamp not working n/s o/s (4.2.1 (a) (ii)) | 1 |
| Stop lamp(s) not working n/s o/s (4.3.1 (a) (ii)) | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Rear Service brake excessively binding n/s o/s (1.2.1 (f)) | 1 |
| Nearside Front Vehicle structure inadequately repaired such that it is likely to adversely affect braking or steering (6.1.1 (d) (ii)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Windscreen washer control is inaccessible to the driver |8.2.1a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing by anti roll bar d mount |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded by subframe mount |2.4.A.3| | 1 |
| Nearside Front Torque/reaction arm rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Torque/reaction arm has a deteriorated rubber bush resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear rear brake excessively fluctuating |3.7.B.3| | 1 |
| Offside Rear rear brake excessively fluctuating |3.7.B.3| | 1 |
| Front Headlamps matched pair are not the same colour |1.7.6| | 1 |
| Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Nearside Front Front suspension ball joint dust cover missing |2.4.G.2| | 1 |
| Offside Front Front suspension ball joint dust cover missing |2.4.G.2| | 1 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Rear Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Exhaust mounting missing |7.1.1b| | 1 |
| Offside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Fuel system component leaking |7.2.3| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Anti-lock braking system warning lamp does not illuminate |3.4.1b| | 1 |
| Brake hose has insufficient room to move | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion WING |6.1.C.1| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion WING |6.1.C.1| | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Centre Stop lamp insecure |1.2.1a| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Parking brake lever ratchet mechanism is broken |3.1.5| | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Front brake application uneven | 1 |
| front brakes release unevenly |3.7.B.4| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Brakes imbalanced across an axle | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |