| Most common failures | No# failures |
|---|
| Registration plate lamp issues | 21 |
| Service brake: efficiency below requirements |3.7.B.7| | 17 |
| Headlamp aim out of alignment | 14 |
| Windscreen wiper does not clear the windscreen effectively | 10 |
| Offside Rear fog lamp not working |1.3.2b| | 8 |
| Brakes imbalanced across an axle | 6 |
| Brake pipe excessively corroded | 6 |
| Rear brake application uneven | 6 |
| Brake hose excessively deteriorated | 6 |
| Horn not working |1.6.2a| | 5 |
| Nearside Side repeater not working |1.4.A.2c| | 5 |
| Indicator switch faulty |1.4.A.1| | 5 |
| Offside Stop lamp not working |1.2.1b| | 5 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 5 |
| Nearside Stop lamp not working |1.2.1b| | 5 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 4 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 3 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
| Front brake application uneven | 3 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
| Emissions not tested |7.0| | 3 |
| Offside Front Side repeater not working |1.4.A.2c| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 3 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 2 |
| Rear Rear fog lamp not working |1.3.2b| | 2 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Nearside Front Side repeater not working |1.4.A.2c| | 2 |
| Stop lamp not working |1.2.1b| | 2 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
| Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 2 |
| Registration plate issues | 2 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Seat belt retracting mechanism defective |5.2.5b| | 2 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 2 |
| Nearside rear brakes release unevenly |3.7.B.4| | 2 |
| Brake load sensing valve linkage seized |3.6.E.3| | 2 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 2 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Rear Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
| Headlamp not working on main beam |1.7.5a| | 1 |
| Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement |2.4.B.2| | 1 |
| Offside Front Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 1 |
| Front front brakes release unevenly |3.7.B.4| | 1 |
| Rear front parking brake recording little or no effort |3.7.B.6a| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Rear Brake rod has restricted free movement |3.5.1k| | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Rear Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i)) | 1 |
| Offside Rear Oil leaking excessively from transmission (8.4.1 (a) (i)) | 1 |
| Offside Front Passenger`s seat insecure |6.2.A.1| | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Brake load sensing valve seized |3.6.E.3| | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
| Offside Front Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Headlamp aim beam image kick up to the offside Both |1.8| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded Front hanger X 2 |inner & outer face of chassis leg| |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded front hanger |outer face of chassis leg| |2.4.A.3| | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is fractured |2.4.A.3| | 1 |
| Nearside Rear Brake pipe inadequately supported and fouling on axle |3.6.B.1| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 1 |
| rear parking |secondary| brakes imbalanced | 1 |
| Headlamp aim beam image kick up to the offside both |1.8| | 1 |
| Direction indicators not working |1.4.A.2c| | 1 |
| Offside Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
| Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is inadequately repaired |3.6.C.3| | 1 |
| Nearside Rear fog lamp not working |1.3.2b| | 1 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| An item not tested |Manual| | 1 |
| Towbar component insecure |6.6.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Driver`s seat insecure |6.2.A.1| | 1 |
| Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Direction indicators not in good working order |function impaired| |1.5.A1b| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Fuel system component leaking |7.2.3| | 1 |
| Brake vacuum build up too slow |3.3.E.6| | 1 |
| Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 1 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Fuel cap/sealing device sealing washer missing |7.2.4c| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Rear Leaf spring fractured |2.4.B.1a| | 1 |
| Nearside Rear Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 1 |
| Nearside Rear Leaf spring has excessive wear in an anchor pin and/or bush |2.4.B.2| | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Mechanical brake component has restricted free movement | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Rear Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Nearside Side repeater incorrect colour |1.4.A.2f| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Windscreen has damage | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Offside Stub axle has excessive vertical movement between stub axle and axle beam |2.5.A.1a| | 1 |
| Nearside Rear Direction indicators not in good working order |function impaired| |1.5.A1b| | 1 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 1 |
| Offside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 1 |
| Position lamp switch faulty |1.1.A.1| | 1 |
| Offside Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Nearside Front Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Brake master cylinder fluid level below minimum level |3.6.G.1e| | 1 |
| Offside Front Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Rear Braking system leaking |3.6.A.1| | 1 |
| Front Brake pipe inadequately clipped under bonnet around bulkhead |3.6.B.1| | 1 |
| Offside Front Drag link end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Axle king pin has excessive play in pin and/or bush adversely affecting the steering both n/s and o/s kingpins have play up an down |2.5.A.3a| | 1 |
| Offside Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Front Brake servo insecurely mounted |3.6.A.2a| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Rear brake binding | 1 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Centre Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Offside Rear Upper Shock absorber insecure |2.7.2b| | 1 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Nearside Direction indicator adversely affected by the operation of another lamp bad earth (4.4.3 (b)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Direction indicator incomplete |1.5.A1b| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Nearside Rear Direction indicator excessively deteriorated so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |