Most common failures | No# failures |
---|
Service brake: efficiency below requirements |3.7.B.7| | 23 |
Offside Rear fog lamp not working |1.3.2b| | 20 |
Brakes imbalanced across an axle | 18 |
Windscreen wiper does not clear the windscreen effectively | 15 |
Registration plate lamp issues | 12 |
Headlamp aim out of alignment | 12 |
Rear fog lamp tell tale not working |1.3.1b| | 11 |
Brake pipe excessively corroded | 10 |
Parking brake: efficiency below requirements |3.7.B.7| | 10 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
Rear brake binding | 9 |
Rear brake application uneven | 8 |
Offside Headlamp not working on dipped beam |1.7.5a| | 8 |
Rear parking brake recording little or no effort | 8 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 7 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Offside rear brake recording little or no effort |3.7.B.5a| | 6 |
Bonnet cannot be secured in the closed position |8.4.1| | 5 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 5 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 4 |
Registration plate issues | 4 |
Nearside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 4 |
Horn not working |1.6.2a| | 4 |
Driver`s seat insecure |6.2.A.1| | 3 |
Offside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 3 |
Offside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 3 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 3 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 3 |
Nearside Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 3 |
Nearside Side repeater not working |1.4.A.2c| | 3 |
Offside Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 3 |
Nearside Headlamp not working on main beam |1.7.5a| | 3 |
Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
Offside front brake binding |3.7.B.1| | 3 |
Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 3 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
Steering system has excessive free play detected at the steering wheel |steering box fitted| |2.2.A.1a| | 2 |
Nearside Front Direction indicator not working |1.4.A.2c| | 2 |
Brake load sensing valve seized |3.6.E.3| | 2 |
Brake hose excessively deteriorated | 2 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
Offside Headlamp aim beam image kick up to the offside |1.6.B1| | 2 |
Nearside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 2 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 2 |
Offside Front brake disc excessively pitted |3.5.1h| | 2 |
Fuel system component leaking |7.2.3| | 2 |
Offside Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 2 |
Direction indicators not working |1.4.A.2c| | 2 |
Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
Rear Drag link end ball joint has excessive play |2.2.B.1f| | 2 |
Offside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
Offside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 2 |
Brake load sensing valve linkage seized |3.6.E.3| | 2 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Headlamp not working on main beam |1.7.5a| | 2 |
Front Exhaust system not adequately supported |7.1.1| | 2 |
Nearside Rear Direction indicator not working |1.4.A.2c| | 2 |
Driver`s door cannot be opened from inside the vehicle |6.2.B.1b| | 2 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
Offside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 2 |
Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Headlamp aim beam image kick up to the offside |1.8| | 2 |
Offside Indicator tell tale inoperative |1.4.A.2a| | 2 |
Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 2 |
Offside Front Shock absorbers has a serious fluid leak | 2 |
Rear fog lamp not working |1.3.2b| | 2 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 2 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
Rear fog lamp insecure |1.3.2a| | 2 |
Offside Side repeater not working |1.4.A.2c| | 2 |
Indicator switch insecure |1.4.A.1| | 2 |
Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 2 |
Rear Rear fog lamp not working |1.3.2b| | 1 |
Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
Front Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Rear Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
Offside Rear fog lamp missing |1.3.2a| | 1 |
Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Steering column movement between the shaft and steering wheel |2.1.2b| | 1 |
Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Nearside Front Lower Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
Offside Front Brake hose leaking |3.6.A.1| | 1 |
Front Fuel system component leaking |7.2.3| | 1 |
Offside Stop lamp not working |1.2.1b| | 1 |
Nearside Front Passenger`s seat insecure |6.2.A.1| | 1 |
Rear Exhaust system not adequately supported |7.1.1| | 1 |
Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Nearside Inner Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Lower Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Nearside Headlamp aim beam image kick up to the offside |1.6.B1| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
Offside Front front brake juddering severely |3.7.A.2b| | 1 |
Rear Drag link end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Front cross member holed (5.3.6 (a) (ii)) | 1 |
Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Nearside Front Shock absorber detached |2.7.2b| | 1 |
Nearside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Seat belt anchorage prescribed area is excessively corroded Near side step area |5.2.6| | 1 |
Nearside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Rear position lamp|s| not in a clean condition and function impaired |1.1.4a| | 1 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Rear rear brake juddering severely |3.7.A.5b| | 1 |
Nearside Front Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.2| | 1 |
Service brake: efficiency below requirements |3.7.D.4| | 1 |
Parking brake: efficiency below requirements |3.7.D.4| | 1 |
Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Axle beam has excessive vertical movement between stub axle and axle beam |2.5.A.1a| | 1 |
Nearside Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
Nearside Rear Seat belt affected by an insecure seat fixing |5.2.1b| | 1 |
Offside Direction indicator not working |1.4.A.2c| | 1 |
Nearside Stop lamp not working |1.2.1b| | 1 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Rear Statutory seat belt missing |5.1.1| | 1 |
Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
Nearside Seat belt retracting mechanism defective |5.2.5b| | 1 |
Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Direction indicator not working |1.4.A.2c| | 1 |
Indicator tell tale inoperative |1.4.A.2a| | 1 |
Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
Rear reflector missing |1.5.1a| | 1 |
Emissions not tested |7.0| | 1 |
Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Rear Wheel stud|s| missing |4.2.A.1e| | 1 |
Offside Front brake disc excessively scored |3.5.1h| | 1 |
Nearside Front Obligatory mirror insecure |8.1.1| | 1 |
Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
Front passenger seat insecure |6.2.3| | 1 |
Nearside Front Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Front Brake pipe leaking |3.6.A.1| | 1 |
Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Brake load sensing valve defective and function impaired |3.6.E.3| | 1 |
Offside Front Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt steering arm from drop arm front boot |2.2.C.1c| | 1 |
Offside Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt steering arm from drop arm rear boot |2.2.C.1c| | 1 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Rear Shock absorber detached |2.7.2b| | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected BY spring mounting (5.3.6 (a) (ii)) | 1 |
Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected BY spring mounting (5.3.6 (a) (ii)) | 1 |
Offside Steering component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Steering box mount (2.1.2 (e) (ii)) | 1 |
Nearside Front Brake master cylinder/servo mounting prescribed area is excessively corroded and functionality of the braking system is affected (1.1.21 (e) (ii)) | 1 |
Lower Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced Font crossmember under rad (6.1.1 (b) (ii)) | 1 |
Rear Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced Inbetwween chassis rails (6.1.1 (b) (ii)) | 1 |
Nearside Front Integral body structure is deformed and structural rigidity is significantly reduced Front bulkhead (6.1.1 (a) (i)) | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Offside Front Axle king pin is loose in the axle beam (5.1.2 (d) (i)) | 1 |
Nearside Front Axle king pin is loose in the axle beam (5.1.2 (d) (i)) | 1 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Prop shaft bearing excessively worn Center mount (6.1.7 (b) (i)) | 1 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Centre Exhaust system not adequately supported |7.1.1| | 1 |
Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Rear fog lamp tell-tale not working |4.9.1 |a| |ii|| | 1 |
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |1.1.21 |e| |i|| | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced bulkhead |6.1.1 |c| |i|| | 1 |
Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected spring mounting |5.3.6 |a| |ii|| | 1 |
Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected spring mounting and chassis |5.3.6 |a| |ii|| | 1 |
Offside Front Steering component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected steering box mounting plate to chassi |2.1.2 |e| |ii|| | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced propshaft mounting |6.1.1 |c| |i|| | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under step |7.1.1 |a| |i|| | 1 |
Rear Vehicle structure strengthening plate or fastening insecure between chassis rails |6.1.1 |b| |i|| | 1 |
Nearside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
Nearside Front Service brake lagging in operation |1.2.1 |d|| | 1 |
Nearside Rear Upper Direction indicator not working |1.4.A.2c| | 1 |
Nearside Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Front brake application uneven | 1 |
Nearside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
Offside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
Centre Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
Offside Rear Leaf spring fractured |2.4.B.1a| | 1 |
Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
Towbar component insecure |6.6.1| | 1 |
Windscreen has damage | 1 |
Electrical wiring inadequately supported |1.9.2a| | 1 |
Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Central Exhaust has a major leak of exhaust gases At silencer (6.1.2 (a)) | 1 |
Rear Exhaust has a major leak of exhaust gases Tail pipe (6.1.2 (a)) | 1 |
Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Rear Body panel corroded and likely to cause injury Corroded with sharp edges (6.2.1 (a) (i)) | 1 |
Offside Steering component mounting prescribed area is excessively corroded Bulkhead extensively corroded / missing at column bottom mount (2.1.2 (e) (i)) | 1 |
Offside Front Cab steps in such a condition that it is likely to cause injury (6.2.8 (b)) | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired Not continuously welded (5.3.6 (a) (i)) | 1 |
Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
front brake recording little or no effort |3.7.B.5a| | 1 |
Rear front brake recording little or no effort |3.7.B.5a| | 1 |
Brake pedal creeps down when held under pressure |3.3.B.1a| | 1 |
Electrical wiring insecure |1.9.2a| | 1 |
Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
Offside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
Nearside Seat belt locking mechanism does not secure or release stalk missing |5.2.5a| | 1 |
Nearside Rear Body has a sharp edge caused by corrosion wheel arch and sill |6.1.C.1| | 1 |
Horn control missing |1.6.1| | 1 |
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Windscreen washer control is inaccessible to the driver |8.2.1a| | 1 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Dipswitch operation does not deflect all main beam headlamps to make them dipped beams |1.7.4b| | 1 |
Nearside Outer Statutory seat belt of the wrong type. |5.1.1| | 1 |
Nearside rear brake grabbing severely |3.7.A.5b| | 1 |
Nearside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
Offside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Front Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 1 |
Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear Mechanical brake component has restricted free movement | 1 |
Nearside Rear Brake cable has restricted free movement |3.5.1k| | 1 |
Nearside Front Side repeater not working |1.4.A.2c| | 1 |
Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
Nearside Rear rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
Offside Front Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
Indicator switch faulty |1.4.A.1| | 1 |
Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Offside Front Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Front front brake juddering severely |3.7.A.2b| | 1 |
Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
Brake master cylinder/servo mounting prescribed area is excessively corroded |1.1.21 |e| |i|| | 1 |
Nearside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
Nearside Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Offside Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Front Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Rear Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Nearside Front Leaf spring anchor bracket corroded and seriously weakened |5.3.1 |b| |i|| | 1 |
Offside Front Leaf spring anchor bracket corroded and seriously weakened |5.3.1 |b| |i|| | 1 |
Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |