| Most common failures | No# failures |
|---|
| Brakes imbalanced across an axle | 40 |
| Registration plate lamp issues | 38 |
| Headlamp aim out of alignment | 37 |
| Windscreen wiper does not clear the windscreen effectively | 34 |
| Brake pipe excessively corroded | 25 |
| Service brake: efficiency below requirements |3.7.B.7| | 20 |
| Parking brake: efficiency below requirements |3.7.B.7| | 17 |
| Offside Rear fog lamp not working |1.3.2b| | 15 |
| Rear fog lamp not working |1.3.2b| | 14 |
| Rear fog lamp tell tale not working |1.3.1b| | 13 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 12 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 11 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 11 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 10 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
| Rear brake application uneven | 9 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 9 |
| Rear parking brake recording little or no effort | 9 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 8 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 8 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Brake load sensing valve linkage seized |3.6.E.3| | 7 |
| Horn not working |1.6.2a| | 7 |
| Registration plate issues | 7 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 6 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 6 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Offside Stop lamp not working |1.2.1b| | 6 |
| Rear Exhaust system not adequately supported |7.1.1| | 6 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 6 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Front brake application uneven | 5 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 5 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 5 |
| Rear brake binding | 5 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
| Offside Headlamp not working on main beam |1.7.5a| | 5 |
| Offside Rear fog lamp insecure |1.3.2a| | 4 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 4 |
| Nearside Headlamp not working on main beam |1.7.5a| | 4 |
| Fuel system component leaking |7.2.3| | 4 |
| Offside Front Direction indicator not working |1.4.A.2c| | 4 |
| Nearside Stop lamp not working |1.2.1b| | 4 |
| Offside Front Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 4 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 4 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 4 |
| Exhaust system not adequately supported |7.1.1| | 4 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
| Nearside Rear Stop lamp not working |1.2.1b| | 4 |
| Offside Rear Stop lamp not working |1.2.1b| | 4 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 4 |
| Offside front brake binding |3.7.B.1| | 4 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
| Indicator tell tale inoperative |1.4.A.2a| | 3 |
| Indicator switch faulty |1.4.A.1| | 3 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 3 |
| Windscreen washer not working | 3 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Front brake disc in such a condition that it is seriously weakened | 3 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Steering system has excessive free play detected at the steering wheel |steering box fitted| |2.2.A.1a| | 3 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 3 |
| Hazard warning lamps inoperative |1.4.B.1b| | 3 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Offside Rear Braking system leaking |3.6.A.1| | 3 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 3 |
| Brake hose excessively deteriorated | 3 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Offside Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 3 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 3 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Hazard warning switch faulty |1.4.B.1d| | 3 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 3 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Parking brake lever has no reserve travel |3.1.6b| | 3 |
| Nearside Side repeater not working |1.4.A.2c| | 3 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Fuel tank leaking |7.2.3| | 3 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 3 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 3 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 3 |
| Nearside Rear Direction indicator flashing less than 60 times a minute |1.4.A.2g| | 2 |
| Offside Rear Direction indicator flashing less than 60 times a minute |1.4.A.2g| | 2 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 2 |
| Main beam `tell-tale` not working |1.7.4c| | 2 |
| Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 2 |
| Offside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 2 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 2 |
| Nearside front brake juddering severely |3.7.A.2b| | 2 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded (1.1.21 (e) (i)) | 2 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 2 |
| Offside Front front brake binding |3.7.B.1| | 2 |
| Offside Seat belt retracting mechanism defective |5.2.5b| | 2 |
| Rear Mechanical brake component has restricted free movement | 2 |
| Rear All position lamps adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 2 |
| Nearside Rear Lower Stop lamp not working |1.2.1b| | 2 |
| Offside Front Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 2 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 2 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 2 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Rear Brake hose bulging under pressure |3.6.B.3| | 2 |
| Offside Front brake disc excessively pitted |3.5.1h| | 2 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Front Brake pipe inadequately supported |3.6.B.1| | 2 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Upper Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
| Driver`s seat insecure |6.2.A.1| | 2 |
| Front Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Nearside Passenger`s seat insecure |6.2.A.1| | 2 |
| Offside Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 2 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 2 |
| Rear Rear fog lamp not working |1.3.2b| | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Rear Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 2 |
| Hazard warning switch inoperative (4.4.2 (a) (ii)) | 2 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Direction indicators not working |1.4.A.2c| | 2 |
| Nearside Rear position lamp|s| incorrect colour |1.1.A.3e| | 2 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 2 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 2 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 2 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 2 |
| Nearside Drag link end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Rear Exhaust has a part missing |7.1.1a| | 2 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 2 |
| Brake load sensing valve seized |3.6.E.3| | 2 |
| Brake performance not tested |3.7.A.1| | 2 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 2 |
| Offside Indicator tell tale inoperative |1.4.A.2a| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Emissions not tested |7.0| | 2 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Rear Brake load sensing valve linkage obviously incorrectly adjusted |3.6.E.3| | 1 |
| Rear Direction indicator flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Offside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Rear Lower Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement |2.4.B.2| | 1 |
| Offside Rear Lower Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement |2.4.B.2| | 1 |
| Offside Front Road wheel badly damaged |4.2.A.1a| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Drag link end ball joint dust cover missing both ends (2.1.3 (g) (ii)) | 1 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Windscreen wiper not working (3.4 (a)) | 1 |
| Nearside Rear Direction indicators not working |1.4.A.2c| | 1 |
| Rear brake drum contaminated by oil |3.5.1h| | 1 |
| rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill has a hole (6.1.1 (c) (i)) | 1 |
| Nearside Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Fuel hose leaking |7.2.3| | 1 |
| Offside Front Outer Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt rear |2.2.C.1c| | 1 |
| Offside Front Driver`s door does not latch securely closed |6.2.B.1a| | 1 |
| Nearside Rear Leaf spring eye defective |anchor| |2.4.B.1b| | 1 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp lamp dims with indicator (4.2.3 (c)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp lamp dims with indicator (4.2.3 (c)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near leaf spring mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis near leaf spring mount (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect no pattern (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect no pattern (4.1.2 (c)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Nearside Front Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Brake load sensing valve linkage obviously incorrectly adjusted |3.6.E.3| | 1 |
| Nearside Rear An item not tested |Manual| | 1 |
| Rear Fuel system component insecure |7.2.1| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch area. |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch area. |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Step area, within 30cm of fuel tank mount. |6.2.2 |d| |i|| | 1 |
| Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen |3.5 |a|| | 1 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view |3.3 |b| |ii|| | 1 |
| Offside Rear Upper Position lamp not working |4.2.1 |a|| | 1 |
| Front Headlamp aim so that beam "kick up" is not visible on the screen Both front headlight images distorted and no kick up visible. |4.1.2 |a|| | 1 |
| Front Exhaust has a major leak of exhaust gases At flexy section. |6.1.2 |a|| | 1 |
| Offside Front Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt Both ball joint covers split. |2.1.3 |g| |ii|| | 1 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt Full track rod and track rod end one unit. |2.1.3 |g| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases rear section |7.1.2| | 1 |
| Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Stop lamp not working All rear. |1.2.1b| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect Bulb incorrectly seated |headlamp low| |1.8.A.1b| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Nearside Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Offside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
| Nearside Rear Leaf spring fractured |2.4.B.1a| | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Front Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced step (7.1.1 (a) (i)) | 1 |
| Offside Front Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt front joint (2.1.3 (g) (ii)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Lower Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Offside Rear Additional braking device leaking oil |3.6.I.6| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded Inner wing |3.6.C.3| | 1 |
| Offside Front Direction indicators not working |1.4.A.2c| | 1 |
| Rear position lamp|s| adversely affected by the operation of another lamp All upper and lower lights |1.1.A.3f| | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |1.1.21 |e| |i|| | 1 |
| Offside Front Steering component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (2.1.2 (e) (ii)) | 1 |
| Nearside Fuel hose leaking at fuel filter (6.1.3 (b) (i)) | 1 |
| Offside Front Lower Steering component mounting prescribed area is excessively corroded (2.1.2 (e) (i)) | 1 |
| Offside Front Steering linkage ball joint ball joint dust cover missing x2 dust covers (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Parking brake mechanism/associated mounting prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
| Offside Rear Parking brake mechanism/associated mounting prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
| Nearside Front Track rod end ball joint dust cover missing (2.1.3 (g) (ii)) | 1 |
| Offside Front Direction indicators missing |1.4.A.2b| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear Shock absorber insecure |2.7.2b| | 1 |
| Nearside Rear Service brake lagging in operation |1.2.1 |d|| | 1 |
| Offside Rear Service brake lagging in operation |1.2.1 |d|| | 1 |
| Offside Rear Brake load sensing valve linkage defective and function impaired Lever broken |1.1.17 |a|| | 1 |
| Offside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Front Exhaust has a major leak of exhaust gases Exhaust joint insecure and blowing |6.1.2 |a|| | 1 |
| Offside Front Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt Front ball joint |2.1.3 |g| |ii|| | 1 |
| Offside Front Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt Rear ball joint |2.1.3 |g| |ii|| | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Emissions not tested due to exhaust system having major leak of gasses (8.2.2.2 (e)) | 1 |
| Brake load sensing valve linkage defective and function impaired (1.1.17 (a)) | 1 |
| Offside Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Nearside Front Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Nearside Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Windscreen has damage | 1 |
| All direction indicators not working |4.4.1 |a| |ii|| | 1 |
| Indicator switch inoperative |4.4.2 |a| |ii|| | 1 |
| Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Nearside Rear Outer Bumper damaged and likely to cause injury when grazed or contacted |6.1.4 |a| |i|| | 1 |
| Nearside Lower Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Nearside Lower Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Lower Direction indicator not working |1.4.A.2c| | 1 |
| Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Rear Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 1 |
| Nearside All position lamps not working |4.2.1 |a|| | 1 |
| Nearside Windscreen wiper not working |3.4 |a|| | 1 |
| Nearside Rear Air suspension unit totally deflated |2.4.D.1a| | 1 |
| Offside Rear Air suspension unit totally deflated |2.4.D.1a| | 1 |
| Offside Upper Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Lower Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Rear Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Headlamp switch faulty |1.7.1| | 1 |
| Dipswitch operation does not extinguish all main beam headlamps leaving at least one pair of dipped beam headlamps |1.7.4b| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Brake valve leaking |3.6.A.1| | 1 |
| Rear Brake valve leaking |3.6.A.1| | 1 |
| Front Lower Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Offside Front brake caliper has restricted free movement |3.5.1k| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Front Exhaust has a part missing |7.1.1a| | 1 |
| Nearside Front Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Offside Upper Stop lamp not working |1.2.1b| | 1 |
| Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Central Exhaust system not adequately supported |7.1.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases tailpipe missing |7.1.2| | 1 |
| Brake fluid warning lamp illuminated |3.6.G.2| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front panel (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect kick off wrong side (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect kick off wrong side (4.1.2 (c)) | 1 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Steering box has relative movement between sector shaft and the drop arm |2.2.B.1b| | 1 |
| Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded inner wing |2.1.2 |e| |i|| | 1 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
| All position lamps not working |1.1.A.3b| | 1 |
| Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Centre Exhaust system not adequately supported |7.1.1| | 1 |
| Rear Brake lever has restricted free movement |3.5.1k| | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mounting (5.3.6 (a) (i)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Stop lamp(s) likely to become detached (4.3.1 (c) (ii)) | 1 |
| Nearside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Side repeater lens defective such that the emitted light is adversely affected (4.4.1 (b) (ii)) | 1 |
| Offside Side repeater not working |1.4.A.2c| | 1 |
| An item not tested |Manual| | 1 |
| Nearside Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
| Offside Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| rear brakes release unevenly |3.7.B.4| | 1 |
| Offside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Rear Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Seat belt affected by an insecure seat fixing |5.2.1b| | 1 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |
| Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Front passenger seat insecure |6.2.3| | 1 |
| Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Front Headlamp aim projected beam image is obviously incorrect Both Sides - HID KIT FITTED (4.1.2 (c)) | 1 |
| Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Nearside Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Upper Position lamp not working |4.2.1 |a|| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded cross member. |2.4.A.3| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering chassis chalked . |6.1.A.1| | 1 |
| Offside Front Outer Vehicle structure has excessive corrosion which adversely affects braking or steering chassis chalked in wheel arch tub. |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings in wheel arch tub |upper| |6.1.B.2| | 1 |
| Nearside Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings in wheel arch tub. |6.1.B.2| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded under bonnet. |3.6.C.3| | 1 |
| Nearside Front Brake master cylinder/servo mounting prescribed area is excessively corroded under bonnet. |3.6.C.3| | 1 |
| Central Brake master cylinder/servo mounting prescribed area is excessively corroded under bonnet |chalked| |3.6.C.3| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is severely distorted |3.6.C.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Front Electrical wiring likely to touch hot or rotating parts brake warning wire (4.11 (a) (iii)) | 1 |
| Nearside Rear Integral body structure modified such that structural rigidity is significantly reduced stabiliser insecure (6.1.1 (d) (i)) | 1 |
| Drag link end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt both gaiters at either end |2.2.C.1c| | 1 |
| Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt both gaiters at either end |2.2.C.1c| | 1 |
| Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded Inner arch |2.4.A.3| | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings bulk head |6.1.B.2| | 1 |
| Electronic stability system warning lamp indicates a fault |3.4.1c| | 1 |
| Exhaust emits clearly visible black smoke during acceleration |8.2.1.2 |g|| | 1 |
| Offside Front Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
| Offside Front Indicator switch faulty |1.4.A.1| | 1 |
| Front Bonnet retaining device excessively deteriorated |8.4.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Horn not a continuous or uniform sound |1.6.2e| | 1 |
| Rear Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |
| Nearside Front Leaf spring anchor bracket corroded and seriously weakened |2.4.B.6d| | 1 |
| Offside Front Leaf spring anchor bracket corroded and seriously weakened |2.4.B.6d| | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Brake load sensing valve linkage defective and function impaired missing (1.1.17 (a)) | 1 |
| Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i)) | 1 |
| Rear Service brake application uneven across the axle |3.7.D.2b| | 1 |
| Parking brake: efficiency below requirements |3.7.D.4| | 1 |
| Offside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Rear fog lamp insecure |1.3.2a| | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Front Braking system leaking brake pipe |3.6.A.1| | 1 |
| Nearside Rear Shock absorber insecure |2.7.2b| | 1 |
| Offside Front Braking system leaking |3.6.A.1| | 1 |
| Nearside Rear Brake pipe leaking |3.6.A.1| | 1 |
| Dipswitch does not operate immediately when selected on dipped beam |4.1.3 |b|| | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Rear All direction indicators adversely affected by the operation of another lamp INTERFERING WITH REG PLATE LAMPS AND POSITION LAMPS (4.4.3 (b)) | 1 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii)) | 1 |
| Nearside Front Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting WHEEL ARCH (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting WHEEL ARCH (6.2.2 (d) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 1 |
| Offside Stop lamp(s) lens defective such that the emitted light is adversely affected nearly white (4.3.1 (b) (ii)) | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded by master cylinder mount (1.1.21 (e) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction garland in view |3.1 |a| |ii|| | 1 |
| Offside Front Body component damaged and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Offside Front Service brake excessively fluctuating |1.2.1 |e|| | 1 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction fluffy items |3.1 |a| |ii|| | 1 |
| Offside Stop lamp|s| showing white light to the rear |4.3.3 |a| |ii|| | 1 |
| Dipswitch does not operate immediately when selected on main beam |4.1.3 |b|| | 1 |
| Headlamp not working on main beam both |4.1.1 |a| |ii|| | 1 |
| Front Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Rear Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Offside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Rear brake drum contaminated by brake fluid |3.5.1h| | 1 |
| Offside Brake cable has restricted free movement |3.5.1k| | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength FRONT MOUNTING (5.3.6 (a) (i)) | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded section in two places above and under brake servo mounting (1.1.21 (e) (i)) | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded chassis (1.1.21 (e) (i)) | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength step (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength step (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear Brake load sensing valve seized |3.6.E.3| | 1 |
| Nearside Front Additional braking device insecure |3.6.I.1| | 1 |
| Offside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
| Brake performance not tested burst brake pipe, nearside front |1.2.1 |g|| | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |1.1.21 |e| |i|| | 1 |
| Nearside Front Brake pipe leaking on an air braking system |1.1.11 |b| |i|| | 1 |
| Nearside Rear All position lamps not working |4.2.1 |a|| | 1 |
| Rear fog lamp tell-tale not working |4.9.1 |a| |ii|| | 1 |
| Rear Brake load sensing valve seized and ABS not fitted or inoperative |1.1.17 |c| |ii|| | 1 |
| Nearside Rear Shock absorbers has a serious fluid leak | 1 |
| Nearside Upper Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear Lower Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Front Headlamp light intensity severely reduced both (4.1.4 (a)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Rear Position lamp adversely affected by the operation of another lamp |4.2.3 |c|| | 1 |
| Brake load sensing valve seized and ABS not fitted or inoperative |1.1.17 |c| |ii|| | 1 |
| Nearside Brake servo corroded and excessively weakened |3.6.A.2b| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Rear position lamp|s| has a product on the light source so it is not visible from a reasonable distance both |1.1.A.3d| | 1 |
| Rear Rear position lamp|s| adversely affected by the operation of another lamp x2 |1.1.A.3f| | 1 |
| Front passenger door catch deteriorated so the door cannot be readily opened or closed |6.2.B.2| | 1 |
| Brake hose has insufficient room to move | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded under arch |2.4.A.3| | 1 |
| Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Nearside Service brake is causing the steering wheel to severely pull one way OSF brake almost inop |3.7.C.2| | 1 |
| Offside Front Drag link end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Upper Brake servo insecurely mounted |3.6.A.2a| | 1 |
| Offside Front Lower Brake servo insecurely mounted |3.6.A.2a| | 1 |
| Offside Front Upper Brake pedal excessively corroded corroded with in 12 inches of mounting |3.3.A.1a| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner |5.2.6| | 1 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Stop lamp obscured more than 50% |1.2.1c| | 1 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Nearside Front Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 1 |
| Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
| Driver`s door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |