| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 43 |
| Brake pipe excessively corroded | 42 |
| Headlamp aim out of alignment | 39 |
| Registration plate lamp issues | 35 |
| Brakes imbalanced across an axle | 28 |
| Offside Rear fog lamp not working |1.3.2b| | 19 |
| Parking brake: efficiency below requirements |3.7.B.7| | 19 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 16 |
| Service brake: efficiency below requirements |3.7.B.7| | 16 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 16 |
| Rear parking brake recording little or no effort | 14 |
| Rear fog lamp tell tale not working |1.3.1b| | 13 |
| Horn not working |1.6.2a| | 12 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
| Offside Stop lamp not working |1.2.1b| | 11 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 11 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 10 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 10 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
| Rear fog lamp not working |1.3.2b| | 9 |
| Nearside Stop lamp not working |1.2.1b| | 8 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 8 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 8 |
| Rear brake application uneven | 8 |
| Registration plate issues | 8 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 7 |
| Rear brake binding | 7 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 6 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 6 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 6 |
| Emissions not tested |7.0| | 6 |
| Rear Exhaust system not adequately supported |7.1.1| | 6 |
| Direction indicators not working |1.4.A.2c| | 5 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 5 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 5 |
| Windscreen washer not working | 5 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 5 |
| Offside front brake binding |3.7.B.1| | 5 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 5 |
| Front brake disc in such a condition that it is seriously weakened | 5 |
| Rear Rear fog lamp not working |1.3.2b| | 5 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 5 |
| Nearside Side repeater not working |1.4.A.2c| | 5 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Front brake disc excessively pitted |3.5.1h| | 4 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Offside Side repeater not working |1.4.A.2c| | 4 |
| Fuel system component leaking |7.2.3| | 4 |
| Hazard warning lamps inoperative |1.4.B.1b| | 4 |
| Brake load sensing valve seized |3.6.E.3| | 4 |
| Offside Rear Stop lamp not working |1.2.1b| | 4 |
| Brake hose excessively deteriorated | 4 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 4 |
| Mechanical brake component has restricted free movement | 4 |
| Parking brake lever has no reserve travel |3.1.6b| | 4 |
| Nearside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 4 |
| Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 4 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 4 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 4 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 4 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Nearside front brake binding |3.7.B.1| | 4 |
| Driver`s seat insecure |6.2.A.1| | 3 |
| Offside Rear Brake pipe inadequately clipped |3.6.B.1| | 3 |
| Service brake: efficiency below requirements |3.7.C.1a| | 3 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 3 |
| Front passenger seat insecure |6.2.3| | 3 |
| Offside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 3 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Offside Headlamp not working on main beam |1.7.5a| | 3 |
| Windscreen wiper not operating automatically when switched on |8.2.1b| | 3 |
| Offside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 3 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 3 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 3 |
| Front brake application uneven | 3 |
| Nearside Headlamp not working on main beam |1.7.5a| | 3 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 3 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 3 |
| Brake pedal spongy |3.3.B.1b| | 3 |
| Brake load sensing valve linkage seized |3.6.E.3| | 3 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Offside Rear Position lamp not working |4.2.1 |a|| | 3 |
| Hazard warning switch faulty |1.4.B.1d| | 3 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 3 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 3 |
| Windscreen wiper blade insecure | 3 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 3 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 2 |
| Stop lamp not working |1.2.1b| | 2 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 2 |
| Offside Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 2 |
| Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Rear wheel cylinder leaking |3.6.A.1| | 2 |
| Driver`s door cannot be opened from inside the vehicle |6.2.B.1b| | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front Steering locking device missing |2.2.C.1g| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| All direction indicators light intensity significantly reduced (4.4.3 (a)) | 2 |
| Offside Rear Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 2 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 2 |
| Nearside Rear reflector missing |1.5.1a| | 2 |
| Offside Rear reflector missing |1.5.1a| | 2 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 2 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
| Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear fog lamp missing |1.3.2a| | 2 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Drag link end ball joint has excessive play |2.2.B.1f| | 2 |
| Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 2 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
| Nearside Front Side repeater not working |1.4.A.2c| | 2 |
| Rear Exhaust mounting missing |7.1.1b| | 2 |
| Offside Front Leaf spring anchor bracket corroded and seriously weakened |2.4.B.6d| | 2 |
| Front Exhaust system not adequately supported |7.1.1| | 2 |
| Vehicle Identification Number not permanently displayed |6.3.5.a| | 2 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded (1.1.21 (e) (i)) | 2 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 2 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Rear Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 2 |
| Fuel tank leaking |7.2.3| | 2 |
| Nearside Obligatory mirror insecure |8.1.1| | 2 |
| Nearside Body has a sharp edge caused by damage |6.1.C.1| | 2 |
| Nearside Front Direction indicator incomplete |1.5.A1b| | 2 |
| Bonnet cannot be secured in the closed position |8.4.1| | 2 |
| front brakes release unevenly |3.7.B.4| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Horn not working (7.7 (a)) | 2 |
| Offside Front Position lamp not working |4.2.1 |a|| | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Offside Front Brake hose bulging under pressure |3.6.B.3| | 2 |
| Nearside Side repeater missing |1.4.A.2b| | 2 |
| Offside Front Upper Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Rear Rear fog lamp insecure |1.3.2a| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 2 |
| Offside Front Side repeater not working |1.4.A.2c| | 2 |
| Brake performance not tested |3.7.A.1| | 2 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Rear position lamp|s| insecure |1.1.A.3a| | 2 |
| Exhaust mounting missing |7.1.1b| | 2 |
| Offside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 2 |
| Service brake: efficiency below requirements (3.7.B.7) | 2 |
| Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b) | 2 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 2 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 2 |
| Nearside Front Side repeater insecure |1.4.A.2b| | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Side repeater incomplete |1.5.A1b| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Steering system excessively tight |2.2.D.1| | 1 |
| Nearside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
| Nearside Front Statutory seat belt of the wrong type. |5.1.1| | 1 |
| Lower Fuel tank leaking |7.2.3| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Centre Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Steering component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg (steering box) (2.1.2 (e) (ii)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Nearside Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded leg |2.4.A.3| | 1 |
| Central Prop shaft bearing excessively worn (6.1.7 (b) (i)) | 1 |
| Nearside Rear Brake relay lever has restricted free movement |3.5.1k| | 1 |
| Nearside Rear Rear reflector missing |1.5.1a| | 1 |
| Offside Rear Rear reflector missing |1.5.1a| | 1 |
| Offside Rear Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Brake hose has insufficient room to move | 1 |
| Offside Upper Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Front Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Side repeater incomplete |1.5.A1b| | 1 |
| Nearside Rear Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |
| Offside Front Leaf spring has excessive side play at eye |anchor| |2.4.B.4| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Lower Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
| Front Fuel system component leaking Engine (6.1.3 (b) (i)) | 1 |
| Offside Rear Brake load sensing valve inoperative and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Offside Rear All position lamps adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Rear All position lamps adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Offside Front Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Obligatory mirror missing (3.3 (a)) | 1 |
| Nearside Front Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded Floor to bulkhead (2.1.2 (e) (i)) | 1 |
| Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Indicator switch faulty |1.4.A.1| | 1 |
| Spare wheel carrier insecure |6.4.2| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Rear Shock absorber detached |2.7.2b| | 1 |
| Offside Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Offside Front Direction indicator not working |1.4.A.2c| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Front position lamp|s| not working |1.1.A.3b| | 1 |
| Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Brake pipe leaking |3.6.A.1| | 1 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced n/s/r and o/s/r chassic corroded (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced door step not welded corectly (6.1.1 (b) (ii)) | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Door step |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Door step |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Out rigger |6.1.B.2| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Steering system has excessive free play detected at the steering wheel |steering box fitted| |2.2.A.1a| | 1 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings all areas as marked |6.1.B.2| | 1 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Offside Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Rear fog lamp switch faulty |1.3.1a| | 1 |
| Front front brakes release unevenly |3.7.B.4| | 1 |
| Nearside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Offside Front Brake actuating linkage mounting prescribed area is excessively corroded |3.3.A.2| | 1 |
| Rear Anti-roll bar locating pin insecure |2.4.G.3a| | 1 |
| Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Front Steering locking device missing |2.2.C.1g| | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Direction indicators not working |1.4.A.2c| | 1 |
| Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |
| Steering box has excessive free play detected at the steering wheel |steering box fitted| |2.3 |a| |i|| | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| Offside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Rear Stop lamp(s) all not working not working when side lights on (4.3.1 (a) (iii)) | 1 |
| Nearside Rear Direction indicator adversely affected by the operation of another lamp not working when side lights on (4.4.3 (b)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Suspension spring mounting prescribed area is inadequately repaired not fully welded (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength hole on frame in prescribed area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area is inadequately repaired nsr rear spring mounting not fully welded (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength nsr rear spring mounting prescribed area hole (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Front spring hanger (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect Euro lamp unit (4.1.2 (c)) | 1 |
| Offside Front Brake prescribed area is excessively corroded Driver floor brake peddles (1.1.21 (e) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Drivers step excessively corroded with in Suspension component mounting prescribed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch well (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in-between spring mounts (5.3.6 (a) (i)) | 1 |
| Exhaust fumes causing a danger to health of persons on board Exhaust leaking fumes into cab (6.1.2 (b) (ii)) | 1 |
| Rear Prop shaft joint so worn it is likely to fail (6.1.7 (c) (ii)) | 1 |
| Offside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Nearside Front Leaf spring anchor bracket corroded and seriously weakened |2.4.B.6d| | 1 |
| Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Offside Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Emissions not tested (8.2.2.2 (e)) | 1 |
| Offside Rear Lower Shock absorbers insecurely attached mounting bolt (5.3.2 (a) (i)) | 1 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Fuel system component leaking (6.1.3 (b) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Rear fog lamp switch missing (4.5.3 (a) (ii)) | 1 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Nearside All position lamps not working |1.1.A.3b| | 1 |
| Offside All position lamps not working |1.1.A.3b| | 1 |
| Offside Front Braking system leaking caliper leaking |3.6.A.1| | 1 |
| Horn not loud enough to be heard by another road user |1.6.2b| | 1 |
| Windscreen has damage | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Exhaust system insecure centre (6.1.2 (a)) | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded under bonnet |3.6.C.3| | 1 |
| Nearside Front Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
| Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Rear brake drum contaminated by oil |3.5.1h| | 1 |
| Offside Rear Lower Braking system leaking cylinder |3.6.A.1| | 1 |
| Nearside Direction indicators not working front and rear |1.4.A.2c| | 1 |
| Offside Direction indicators not working front and rear |1.4.A.2c| | 1 |
| Offside Rear Lower Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Offside Front Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Offside Rear All position lamps not working 2 of 3 working |1.1.A.3b| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Nearside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Offside Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Fuel cap/sealing device sealing washer deteriorated |7.2.4c| | 1 |
| Parking brake not fitted on at least two wheels |3.1.1| | 1 |
| Nearside Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Headlamp not working on dipped beam |1.7.5a| | 1 |
| Headlamp not working on main beam |1.7.5a| | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear Rear position lamp|s| flickers when tapped lightly by hand |1.1.4c| | 1 |
| Brake pedal has no servo assistance |3.3.B.2| | 1 |
| Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Front Body component damaged and likely to cause injury BONNET CATCH NOT WORKING (6.2.1 (a) (i)) | 1 |
| Semaphore indicator arm not working (4.4.1 (a) (ii)) | 1 |
| Stop lamp(s) switch with a delay in operation Always on (4.3.2 (a) (ii)) | 1 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Rear Direction indicator light intensity significantly reduced Both sides (4.4.3 (a)) | 1 |
| Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
| Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Nearside Side repeater not working |4.4.1 |a| |ii|| | 1 |
| Exhaust fumes entering cabin |6.1.2 |b| |i|| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Nearside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Body component corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Offside Front Vehicle structure has damage which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Offside Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Offside Inner Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Lower Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Offside Front Lower Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
| Offside Front Lower Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Drag link end ball joint dust cover insecure so that it no longer prevents the ingress of dirt rear |2.2.C.1c| | 1 |
| Nearside Front Cab steps so insecure it is likely to cause injury |6.2.8 |a| |ii|| | 1 |
| Offside Front Cab steps so insecure it is likely to cause injury |6.2.8 |a| |ii|| | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Rear fog lamp tell-tale not working |4.9.1 |a| |ii|| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Headlamp aim not tested |4.1.2 |b|| | 1 |
| Offside Dipswitch operation does not deflect all main beam headlamps to make them dipped beams |4.1.3 |b|| | 1 |
| Nearside Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction |3.1 |a| |ii|| | 1 |
| Nearside Body panel corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Offside Body panel corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Side repeater missing |1.4.A.2b| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Offside Rear rear brake juddering severely |3.7.A.5b| | 1 |
| passenger door does not latch securely closed |6.2.B.1a| | 1 |
| Headlamp not working on dipped beam both |1.7.5a| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear brake drum contaminated by oil |3.5.1h| | 1 |
| Rear Rear fog lamp missing |1.3.2a| | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Front Drag link end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Rear wheel cylinder has restricted free movement |3.5.1k| | 1 |
| Offside wheel cylinder has restricted free movement |3.5.1k| | 1 |
| Nearside Rear Mechanical brake component locking device insecure |3.5.1l| | 1 |
| Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear reflector more than 50% obscured |1.5.1b| | 1 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Offside Fuel tank leaking |7.2.3| | 1 |
| Offside Front Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
| Nearside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Nearside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Leaf spring has a deteriorated anchor pin rubber bush resulting in excessive movement |2.4.B.2| | 1 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
| Nearside Front Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Steering linkage ball joint ball joint dust cover insecure so that it no longer prevents the ingress of dirt both ends split (2.1.3 (g) (ii)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point (6.2.2 (d) (i)) | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded body corrosion (see from underside) (1.1.21 (e) (i)) | 1 |
| brake disc excessively pitted |3.5.1h| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
| Offside Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced step area 2.0 |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced step area 2.0 |6.1.1 |c| |i|| | 1 |
| Rear Brake load sensing valve inoperative |3.6.E.3| | 1 |
| Rear Towbar component excessively corroded |6.6.1| | 1 |
| Nearside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
| Brake master cylinder/servo mounting prescribed area is fractured |3.6.C.3| | 1 |
| Nearside Front Suspension spring mounting prescribed area is fractured spring front mount |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is fractured spring front mount |2.4.A.3| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Inner Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Inner Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Offside rear brake excessively fluctuating |3.7.B.3| | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded 3x places |3.6.C.3| | 1 |
| Stop lamp not working both |1.2.1b| | 1 |
| Nearside Front Lower Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Rear Exhaust fumes causing a danger to health of persons on board exhaust missing |6.1.2 |b| |ii|| | 1 |
| Spare wheel carrier insecure |6.1.5 |a|| | 1 |
| Offside Side repeater not working |4.4.1 |a| |ii|| | 1 |
| Nearside Front Lower Hydraulic brake calliper inadequately mounted carrier bolt loose |1.1.16 |c| |i|| | 1 |
| Nearside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
| Rear Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Outer Front brake disc excessively pitted |3.5.1h| | 1 |
| Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Headlamp does not operate immediately when selected on main beam |1.7.4a| | 1 |
| Offside Headlamp does not operate immediately when selected on main beam |1.7.4a| | 1 |
| Headlamp switch faulty |1.7.1| | 1 |
| Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Suspension spring mounting prescribed area is excessively corroded n/s/f chassis |2.4.A.3| | 1 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
| Nearside Rear wheel cylinder leaking |3.6.A.1| | 1 |
| Front Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Front Upper Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Upper Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Centre Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Nearside rear brake grabbing severely |3.7.A.5b| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Inner Brake master cylinder/servo mounting prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
| Nearside Front Inner Body modification likely to adversely affect braking or steering engine bay (6.2.1 (d) (ii)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced door step (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded steering box (2.1.2 (e) (i)) | 1 |
| Offside Side repeater missing |1.4.A.2b| | 1 |
| Nearside Front An item not tested |Manual| | 1 |
| Offside Front An item not tested |Manual| | 1 |
| Nearside Side repeater not working (1.4.A.2c) | 1 |
| Headlamp not in good working order adversely affecting beam image (1.2.4a) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Body has a sharp edge caused by corrosion (6.1.C.1) | 1 |
| Hazard warning lamps not flashing in phase, with ignition on (1.4.B.1f) | 1 |
| Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f) | 1 |
| Hazard warning tell tale not working correctly (1.4.B.1e) | 1 |
| Nearside Front position lamp(s) not in good working order (function impaired) (1.1.4a) | 1 |
| Nearside Upper Front position lamp(s) not working (1.1.A.3b) | 1 |
| Offside Rear fog lamp not working (1.3.2b) | 1 |
| Indicator tell tale inoperative (1.4.A.2a) | 1 |
| Offside Front front brake binding (3.7.B.1) | 1 |
| Nearside rear brake recording little or no effort (3.7.B.5a) | 1 |
| Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
| Hazard warning lamps inoperative (1.4.B.1b) | 1 |
| Vehicle Identification Number not permanently displayed (6.3.5.a) | 1 |
| Headlamp not working on main beam offside (1.7.5a) | 1 |
| Rear fog lamp not working (1.3.2b) | 1 |
| Rear fog lamp tell tale not working (1.3.1b) | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded offside front lower bulkhead (3.6.C.3) | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded offside front upper bulkhead (3.6.C.3) | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded offside front inner bulkhead inside of vehicle (3.6.C.3) | 1 |
| Brake master cylinder/servo mounting prescribed area is inadequately repaired offside front upper bulkhead repaired with fibreglass/filler (3.6.C.3) | 1 |
| Suspension spring mounting prescribed area is excessively corroded front crossmember (2.4.A.3) | 1 |
| Offside Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3) | 1 |
| Front Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
| Offside Outer Rear Lower Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front of NSF inner wheelarch (5.3.6 (a) (i)) | 1 |
| Nearside Rear position lamp(s) excessively deteriorated so that it is not visible from a reasonable distance (1.1.A.3d) | 1 |
| Offside Rear Braking system leaking |3.6.A.1| | 1 |
| Front Steering system excessively tight |2.2.D.1| | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Bulk head. (5.3.6 (a) (i)) | 1 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Exhaust has a part missing |7.1.1a| | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Offside Front Driver`s door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Offside Side repeater insecure |1.4.A.2b| | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Driver`s door does not latch securely closed |6.2.B.1a| | 1 |
| Offside Rear Direction indicator incomplete |1.5.A1b| | 1 |
| Nearside Front Lower Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Hazard warning switch inoperative (4.4.2 (a) (ii)) | 1 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Nearside Front Direction indicators have less than 50% of the light sources illuminating |1.4.A.2c| | 1 |
| Bonnet retaining device ineffective |8.4.2| | 1 |
| Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Front brake excessively fluctuating | 1 |
| Nearside Front Side repeater incorrect colour |1.4.A.2f| | 1 |
| Nearside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Towbar component insecure |6.6.1| | 1 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Front Brake pipe seriously damaged |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Nearside front brake grabbing severely |3.7.A.2b| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 1 |
| Offside Front Braking system leaking |3.6.A.1| | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 1 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 1 |
| Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Steering system excessively rough (2.1.1 (a)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Offside Front Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Offside Front Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Offside Rear Shock absorbers likely to become detached (Lower bush) (5.3.2 (a) (ii)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Drivers view of the road through the swept area of the windscreen materially affected by an obstruction (3.1 (a) (ii)) | 1 |
| Brake fluid contaminated (1.8 (a)) | 1 |
| Rear Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 1 |
| Fuel cap/sealing device ineffective temporary cap fitted |6.1.3 |b| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch within 12" of shock absorber top mounting as marked |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch within 12" of shock absorber top mount as marked |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail within 12" of shock absorber top mount as marked |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body corner within 12" of leaf spring rear mount as marked |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body corner within 12" of leaf spring rear mount as marked |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis out rigger within 12" of leaf spring rear mount as marked |5.3.6 |a| |i|| | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |1.1.21 |e| |i|| | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded floor pan |2.1.2 |e| |i|| | 1 |
| Emissions not tested vehicle started to over heat |8.2.2.2 |e|| | 1 |
| Nearside Passenger`s seat insecure |6.2.A.1| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect kick up on wrong side - left hand drive headlight fitted |4.1.2 |c|| | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen reflector loose inside headlight |4.1.2 |a|| | 1 |
| Offside Rear fog lamp obscured more than 50% |1.3.2c| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Braking system leaking |3.6.A.1| | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Nearside Front Direction indicator excessively deteriorated so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Front Fuel tank leaking |7.2.3| | 1 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Nearside Front Fuel system component leaking |7.2.3| | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Front Fuel pipe leaking |7.2.3| | 1 |