Most common failures | No# failures |
---|
Registration plate lamp issues | 28 |
Windscreen wiper does not clear the windscreen effectively | 28 |
Brake hose excessively deteriorated | 26 |
Headlamp aim out of alignment | 25 |
Brakes imbalanced across an axle | 24 |
Offside Rear fog lamp not working |1.3.2b| | 21 |
Brake pipe excessively corroded | 17 |
Service brake: efficiency below requirements |3.7.B.7| | 17 |
Parking brake: efficiency below requirements |3.7.B.7| | 13 |
Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 10 |
Offside Headlamp not working on dipped beam |1.7.5a| | 10 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
Rear fog lamp tell tale not working |1.3.1b| | 9 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 8 |
Rear fog lamp not working |1.3.2b| | 8 |
Brake load sensing valve linkage seized |3.6.E.3| | 7 |
Registration plate issues | 7 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 7 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
Horn not working |1.6.2a| | 7 |
Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 6 |
Nearside Stop lamp not working |1.2.1b| | 6 |
Offside rear brake recording little or no effort |3.7.B.5a| | 6 |
Fuel system component leaking |7.2.3| | 6 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 6 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 6 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 6 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 6 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 5 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 5 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 5 |
Offside Front Direction indicator not working |1.4.A.2c| | 5 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 5 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 5 |
Offside Front position lamp|s| not working |1.1.A.3b| | 5 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Nearside front brake binding |3.7.B.1| | 5 |
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 4 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 4 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
Rear brake binding | 4 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
Rear brake application uneven | 4 |
Offside Rear Rear fog lamp not working |1.3.2b| | 4 |
Offside Rear Stop lamp not working |1.2.1b| | 4 |
Hazard warning switch faulty |1.4.B.1d| | 4 |
Rear parking brake recording little or no effort | 3 |
Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 3 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 3 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
Rear Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 3 |
Offside Stop lamp not working |1.2.1b| | 3 |
Brake hose has insufficient room to move | 3 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 3 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
Nearside Rear Stop lamp not working |1.2.1b| | 3 |
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
Nearside Headlamp aim beam image kick up to the offside |1.8| | 3 |
Rear fog lamp tell tale missing |1.3.1b| | 3 |
Brake load sensing valve seized |3.6.E.3| | 3 |
Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 3 |
Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 2 |
Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 2 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
Nearside Rear Direction indicators not working |1.4.A.2c| | 2 |
Front passenger seat insecure |6.2.3| | 2 |
Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 2 |
Central Stop lamp(s) with a multiple light source more than 1/2 not functioning (4.3.1 (a) (ii)) | 2 |
Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
Nearside Rear Direction indicator not working |1.4.A.2c| | 2 |
Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Parking brake lever has no reserve travel |3.1.6b| | 2 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
Headlamp aim not tested (4.1.2 (b)) | 2 |
Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 2 |
Horn not working |7.7 |a| |ii|| | 2 |
Nearside Rear Leaf spring fractured |2.4.B.1a| | 2 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Nearside Front brake disc excessively pitted |3.5.1h| | 2 |
Offside Front brake disc excessively pitted |3.5.1h| | 2 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 2 |
Rear Exhaust has a part missing |7.1.1a| | 2 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
rear brakes release unevenly |3.7.B.4| | 2 |
Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
Nearside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 2 |
Brake performance not tested |3.7.A.1| | 2 |
Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
rear brake recording little or no effort |3.7.B.5a| | 2 |
Nearside Windscreen wiper not operating automatically when switched on |8.2.1b| | 2 |
Offside Windscreen wiper not operating automatically when switched on |8.2.1b| | 2 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
Rear Exhaust system not adequately supported |7.1.1| | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Front Exhaust system not adequately supported |7.1.1| | 2 |
Nearside Obligatory mirror missing |8.1.1| | 2 |
Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 2 |
Offside Front Seat belt retracting mechanism defective |5.2.5b| | 2 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 2 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 2 |
Nearside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 2 |
Windscreen wiper blade insecure | 2 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 2 |
Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 2 |
Power steering malfunctioning |2.3.3a| | 2 |
Offside Front Obligatory mirror insecure |8.1.1| | 1 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Rear Towbar fixing obviously of an inappropriate type |6.6.2| | 1 |
Offside Rear Towbar fixing obviously of an inappropriate type |6.6.2| | 1 |
Hazard warning lamps operated by more than one switch |1.4.B.1c| | 1 |
Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Braking system leaking |3.6.A.1| | 1 |
Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
Offside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
Nearside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Nearside Rear Upper Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
Nearside Rear Upper Direction indicator light intensity significantly reduced (4.4.3 (a)) | 1 |
Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Nearside Rear Upper Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
Offside Rear Upper Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
Brake valve leaking LOAD SENSING VALVE (1.1.7 (d) (i)) | 1 |
Nearside Front Anti-roll bar pin or bush excessively worn ON AXLE (5.3.4 (a) (i)) | 1 |
Offside Front Anti-roll bar pin or bush excessively worn ON AXLE (5.3.4 (a) (i)) | 1 |
Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt BOTH (2.1.3 (g) (ii)) | 1 |
Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
Stop lamp adversely affected by the operation of another lamp coming non with side lights |1.2.1f| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Offside Front Anti-roll bar linkage has excessive play in a pin/bush d bush |2.4.G.2| | 1 |
Offside Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
Nearside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Leaf spring to axle fixing bolt insecure U bolt |5.3.1 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail |5.3.6 |a| |i|| | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch |6.2.2 |d| |i|| | 1 |
Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Upper Stop lamp not working |1.2.1b| | 1 |
Offside Upper Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
Offside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Vehicle Identification Number not permanently displayed |6.3.5.a| | 1 |
Towbar assembly inappropriately modified |6.6.7| | 1 |
Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
Rear fog lamp missing |1.3.2a| | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sharp edge (6.1.1 (c) (i)) | 1 |
Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Rear Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Upper Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced central floor (6.1.1 (c) (i)) | 1 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Fluid leak harmful to the environment or a risk to other road users diesel oil (8.4.1 (a) (i)) | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Front Exhaust system insecure (6.1.2 (a)) | 1 |
Nearside Rear Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
Offside Rear Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
Nearside Front Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
Offside Front Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Front Bonnet retaining device insecure |8.4.2| | 1 |
Nearside Rear Suspension spring mounting prescribed area is severely distorted |2.4.A.3| | 1 |
Nearside Front Suspension spring mounting prescribed area is severely distorted |2.4.A.3| | 1 |
Offside Front Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded door step and jacking point marked yellow |5.2.6| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded jacking point and door step |5.2.6| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings multiple places |6.1.B.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings multiple places |6.1.B.2| | 1 |
Offside Rear Upper Direction indicators not working |1.4.A.2c| | 1 |
Offside Rear Upper Stop lamp not working |1.2.1b| | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Inner Brake master cylinder/servo mounting prescribed area is excessively corroded and functionality of the braking system is affected wheel arch (1.1.21 (e) (ii)) | 1 |
Rear Brake hose damaged and likely to fail (1.1.12 (a)) | 1 |
Dropside likely to become detached (6.2.1 (a) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength spring mount (5.3.6 (a) (i)) | 1 |
Emissions not tested (8.2.1.2 (d)) | 1 |
Front Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 1 |
Nearside Front Headlamp aim not tested |1.8.A.1c| | 1 |
Offside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Front Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Exhaust mounting missing |7.1.1b| | 1 |
Shock absorber has negligible damping effect |2.7.5| | 1 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
Horn not a constant note |1.7.1e| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cab step |6.1.B.2| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings bulkhead below brake servo |6.1.B.2| | 1 |
Nearside Front passenger seat insecure |6.2.3| | 1 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Inner Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Stop lamp not working |1.2.1b| | 1 |
Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Offside Outer Obligatory mirror insecure |8.1.1| | 1 |
Nearside Front Side repeater not working |1.4.A.2c| | 1 |
Rear Brake pipe leaking |3.6.A.1| | 1 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Nearside Side repeater not working |1.4.A.2c| | 1 |
Offside Front Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
Nearside Front Front position lamp|s| not working and marker light |1.1.A.3b| | 1 |
Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Direction indicator not working and not working on hazard |1.4.A.2c| | 1 |
Nearside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
Nearside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
Semaphore indicator tell tale not working correctly |1.4.C.2| | 1 |
Centre Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Rear wheel cylinder has restricted free movement |3.5.1k| | 1 |
Offside Rear wheel cylinder has restricted free movement |3.5.1k| | 1 |
Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
Nearside Passenger`s seat insecure |6.2.A.1| | 1 |
Nearside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
Battery insecure |1.9.1| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
Indicator tell tale inoperative |1.4.A.2a| | 1 |
Main beam `tell-tale` not working |1.7.4c| | 1 |
Nearside Headlamp not working on main beam |1.7.5a| | 1 |
Offside Rear Upper Shock absorber insecure |2.7.2b| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded rear spring mounting |2.4.A.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded rear spring mounting |2.4.A.3| | 1 |
Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Rear Rear fog lamp not working |1.3.2b| | 1 |
Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Windscreen has damage | 1 |
Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` sun visor broken |8.3.1b| | 1 |
Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
Front brake application uneven | 1 |
Offside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 1 |
Nearside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Side repeater incomplete |1.5.A1b| | 1 |
Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
Nearside Front brake caliper leaking |3.6.A.1| | 1 |
Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
Nearside Track rod end ball pin shank loose |2.2.B.1c| | 1 |
Offside Headlamp not working on main beam |1.7.5a| | 1 |
Offside Side repeater not working |1.4.A.2c| | 1 |
Nearside Rear Anti-roll bar linkage insecure |2.4.G.1| | 1 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Front Driver`s seat insecure |6.2.A.1| | 1 |
Nearside Front Lower Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Lower Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Inner Rear position lamp|s| not working |1.1.A.3b| | 1 |
Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
Brake pedal anti-slip provision missing |3.3.A.1b| | 1 |
Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Exhaust emits excessive smoke or vapour likely to obscure the vision of other road users (8.2.2.2 (c)) | 1 |
Nearside Direction indicator not working All (4.4.1 (a) (ii)) | 1 |
Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Fuel system component leaking fuel filter |7.2.3| | 1 |
Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
Rear Exhaust has a major leak of exhaust gases tailpipe |7.1.2| | 1 |
Nearside Front All position lamps not working |1.1.A.3b| | 1 |
Nearside Rear All position lamps not working |1.1.A.3b| | 1 |
Nearside Front Direction indicators not working |1.4.A.2c| | 1 |
Offside Rear Rear reflector missing |1.5.1a| | 1 |
Nearside Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Fuel system component leaking |7.2.3| | 1 |
Nearside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
Nearside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 1 |
Windscreen washer not working | 1 |
Windscreen wiper not working (3.4 (a)) | 1 |
Horn sound not in accordance with requirements (7.7 (c)) | 1 |
All direction indicators not working (4.4.1 (a) (ii)) | 1 |
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded inner wing near bonnet hinge (1.1.21 (e) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing near chassis (5.3.6 (a) (i)) | 1 |
Offside Front Windscreen wiper not working |3.4 |a|| | 1 |
Nearside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
Offside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
Brake servo inoperative |1.1.10 |a| |ii|| | 1 |
Offside Front Brake master cylinder/servo mounting prescribed area is inadequately repaired and functionality of the braking system is affected under servo |1.1.21 |e| |ii|| | 1 |
Nearside Rear Position lamp not working |4.2.1 |a|| | 1 |
Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Bonnet cannot be secured in the closed position |3.1 |b| |i|| | 1 |
Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
Offside Parking brake inoperative on one side |1.4.1 |a|| | 1 |
Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis/ spring mount |5.3.6 |a| |ii|| | 1 |
Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength panel |5.3.6 |a| |i|| | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch/ wing |5.3.6 |a| |i|| | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front panel |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mount |5.3.6 |a| |i|| | 1 |
Offside Rear All position lamps have a product on the lenses or light sources which significantly reduces light intensity effected by indicators |4.2.3 |b| |ii|| | 1 |
Nearside Front Wheel bolt|s| missing |4.2.A.1e| | 1 |
Nearside Rear Wheel bolt|s| missing |4.2.A.1e| | 1 |
Offside Rear Wheel bolt|s| missing |4.2.A.1e| | 1 |
Nearside Rear Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 1 |
Nearside Rear Side repeater not working |1.4.A.2c| | 1 |
Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Rear Brake pipe leaking |3.6.A.1| | 1 |
Exhaust emissions exceed level of metered smoke for a non-turbo charged engine |8.2.2.2 |b|| | 1 |
Brake load sensing valve inoperative and ABS not fitted or inoperative |1.1.17 |c| |ii|| | 1 |
Nearside Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength frontmost spring mounting area |5.3.6 |a| |i|| | 1 |
Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Stop lamp|s| not working both |4.3.1 |a| |ii|| | 1 |
Nearside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Nearside Side repeater not working |4.4.1 |a| |ii|| | 1 |
Central Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
Bonnet cannot be secured in the closed position |8.4.1| | 1 |
Front Exhaust has a major leak of exhaust gases and rear |7.1.2| | 1 |
Offside Rear Rear fog lamp missing |1.3.2a| | 1 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Offside Front Exhaust mounting missing |7.1.1b| | 1 |
Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
Offside Rear brake drum contaminated by oil |3.5.1h| | 1 |
Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Nearside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 1 |
Offside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength leaf spring hanger chassis |5.3.6 |a| |i|| | 1 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Steering box has relative movement between sector shaft and the drop arm |2.2.B.1b| | 1 |
Nearside Front Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Centre Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
Brake master cylinder/servo mounting prescribed area is deliberately modified which significantly reduces the original strength |3.6.C.3| | 1 |
Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
Offside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
Nearside Windscreen wiper blade missing |8.2.2| | 1 |
Offside rear brake juddering severely |3.7.A.5b| | 1 |
Nearside Front Front passenger seat insecure |6.2.3| | 1 |
Nearside Front Side repeater insecure |1.4.A.2b| | 1 |
Ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Nearside Rear Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Offside Rear Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Emissions not tested |7.0| | 1 |
Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Nearside Front front brake binding |3.7.B.1| | 1 |
Offside Front front brake binding |3.7.B.1| | 1 |
Nearside Rear front brake binding |3.7.B.1| | 1 |
Offside Rear front brake binding |3.7.B.1| | 1 |
Offside Front Headlamp aim beam image too far to the right |1.6.B4| | 1 |
Offside Rear Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
Nearside Front brake caliper has restricted free movement |3.5.1k| | 1 |
Nearside Front An item not tested |Manual| | 1 |
Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
Front Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
Offside Rear Hydraulic brake cylinder leaking and braking performance affected (1.1.16 (b) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheelarch within p/e of top shocker mounting (5.3.6 (a) (i)) | 1 |
Offside Front Floor excessively deteriorated floor to arch area corroded and holed (6.2.4 (a) (i)) | 1 |
Nearside Front Floor excessively deteriorated step corroded and holed (6.2.4 (a) (i)) | 1 |
Offside Front Floor excessively deteriorated inner step corroded and holed (6.2.4 (a) (i)) | 1 |
Offside Rear fog lamp missing |1.3.2a| | 1 |
Windscreen wiper blade deteriorated |8.2.2| | 1 |
Brake load sensing valve has been disconnected and was fitted as standard |3.6.E.2| | 1 |
Nearside Outer Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Nearside Outer Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
Nearside Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 1 |
Offside Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Rear Outer Position lamp not working |4.2.1 |a| |ii|| | 1 |
Offside Rear Inner Position lamp not working |4.2.1 |a| |ii|| | 1 |
Nearside Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting step |6.2.2 |d| |i|| | 1 |
Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front upper wheel arch (6.1.1 (c) (i)) | 1 |
Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front upper wheel arch (6.1.1 (c) (i)) | 1 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced step (6.1.1 (c) (i)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member/support bar. (6.1.1 (c) (i)) | 1 |
Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Front Lower Vehicle structure has a fracture which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Front Driver`s seat insecure |6.2.A.1| | 1 |
Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
Offside Front Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Track rod end ball joint dust cover missing |2.2.C.1c| | 1 |
Driver`s seat fore and aft adjustment mechanism not functioning as intended. |6.2.A.3| | 1 |
Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
Driver`s seat fore and aft adjustment mechanism not functioning as intended. |6.2.5 |b| |i|| | 1 |
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded inner wheel arch / bulk head |1.1.21 |e| |i|| | 1 |
Nearside Headlamp aim not tested |1.8.A.1c| | 1 |
Power steering inoperative |2.3.3a| | 1 |
Power steering pump leaking from a failed component |2.3.3b| | 1 |
Direction indicators not working |1.4.A.2c| | 1 |
Nearside Statutory seat belt missing |5.1.1| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded Inner sill step x2 |5.2.6| | 1 |
Brake pedal spongy |3.3.B.1b| | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced b post |7.1.1 |a| |i|| | 1 |
Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wing |6.1.1 |c| |i|| | 1 |
Brake pedal has insufficient reserve travel |1.1.2 |a|| | 1 |
Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wing |6.1.1 |c| |i|| | 1 |
Brake vacuum build up too slow |3.3.E.6| | 1 |