| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 23 |
| Parking brake: efficiency below requirements |3.7.B.7| | 13 |
| Windscreen wiper does not clear the windscreen effectively | 13 |
| Brakes imbalanced across an axle | 12 |
| Registration plate lamp issues | 11 |
| Rear parking brake recording little or no effort | 8 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 8 |
| Service brake: efficiency below requirements |3.7.B.7| | 7 |
| Headlamp aim out of alignment | 6 |
| Offside Headlamp not working on main beam |1.7.5a| | 6 |
| Registration plate issues | 6 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 6 |
| Brake hose excessively deteriorated | 6 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 6 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 5 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Indicator switch faulty |1.4.A.1| | 4 |
| Nearside Stop lamp not working |1.2.1b| | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
| Exhaust system not adequately supported |7.1.1| | 4 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 4 |
| Nearside Headlamp not working on main beam |1.7.5a| | 4 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 4 |
| Driver`s seat insecure |6.2.A.1| | 3 |
| Fuel system component leaking |7.2.3| | 3 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside Side repeater not working |1.4.A.2c| | 3 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Rear brake application uneven | 3 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 3 |
| Rear Exhaust has a part missing |7.1.1a| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 3 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 3 |
| Brake load sensing valve linkage seized |3.6.E.3| | 3 |
| Nearside Front Passenger`s seat insecure |6.2.A.1| | 2 |
| Nearside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Front Exhaust system not adequately supported |7.1.1| | 2 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 2 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 2 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 2 |
| Emissions not tested |7.0| | 2 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 2 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Horn not working |1.6.2a| | 2 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Front Direction indicator not working |1.4.A.2c| | 2 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| All position lamps not working |1.1.A.3b| | 2 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
| Windscreen washer not working | 2 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
| Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Offside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect Kick up to the right (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect Kick up to the right (4.1.2 (c)) | 1 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Front Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Front Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Exhaust emits dense blue smoke at idle |7.4.A.1| | 1 |
| Nearside Obligatory mirror missing |8.1.1| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Nearside Rear Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 1 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Rear Exhaust has a part missing |7.1.1a| | 1 |
| Offside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Offside Front Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Steering wheel retaining device insecure |2.1.6| | 1 |
| Rear brake binding | 1 |
| Offside Rear Rear position lamp|s| obscured more than 50% |1.1.A.3c| | 1 |
| Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Lower Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Offside Upper Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Nearside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside rear brake juddering severely |3.7.A.5b| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| front brake recording little or no effort |3.7.B.5a| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Offside Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Nearside Headlamp aim not tested |1.8.A.1c| | 1 |
| Offside Headlamp aim not tested |1.8.A.1c| | 1 |
| Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Exhaust emits excessive dense blue smoke during acceleration |7.4.A2| | 1 |
| Exhaust emits clearly visible black smoke during acceleration |7.4.A2| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Front passenger seat insecure |6.2.3| | 1 |
| Front Fuel system component leaking |7.2.3| | 1 |
| Offside Front Body has a sharp edge caused by corrosion bumper and outer wing |6.1.C.1| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded rear |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded front |2.4.A.3| | 1 |
| Rear Brake hose bulging under pressure |3.6.B.3| | 1 |
| Rear Brake hose leaking |3.6.A.1| | 1 |
| Driver`s seat fore and aft adjustment mechanism not functioning as intended. |6.2.A.3| | 1 |
| Front Passenger`s seat insecure |6.2.A.1| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 1 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Centre Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
| Fuel hose leaking |7.2.3| | 1 |
| Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Nearside Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
| Rear Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Offside Front Leaf spring fractured |2.4.B.1a| | 1 |
| Nearside Steering pivot point has excessive play |2.2.B.1g| | 1 |
| Offside Ball joint has excessive play |2.2.B.1f| | 1 |
| Brake clevis joint locking device missing |3.5.1l| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Position lamp switch faulty |1.1.A.1| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Centre Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Front Electrical wiring insecure and connectors likely to become disconnected fusebox (4.11 (a) (ii)) | 1 |
| Offside Front Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Steering locking device missing split pin (2.1.3 (d)) | 1 |
| Offside Front Steering locking device missing split pin (2.1.3 (d)) | 1 |
| Nearside Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Rear Vehicle structure is deformed and structural rigidity is significantly reduced both sides separating (6.1.1 (a) (i)) | 1 |
| Passenger`s seat insecure floor around front fixing rusty |6.2.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength step area |5.3.6 |a| |i|| | 1 |
| Windscreen wiper not working |3.4 |a|| | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Offside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Headlamp aim projected beam image is obviously incorrect both headlamps left hand drive beam image |4.1.2 |c|| | 1 |
| Steering locking device missing both outer track rod ends no split pins |2.1.3 |d|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch near shock absorber |5.3.6 |a| |i|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both rear spring mounting |5.3.6 |a| |i|| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Offside Front Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 1 |
| Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Axle king pin has excessive play in pin and/or bush adversely affecting the steering |2.5.A.3a| | 1 |
| Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 1 |
| rear brakes release unevenly |3.7.B.4| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Nearside Front Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Offside Front Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Nearside Rear Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Offside Rear Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Front position lamp|s| not working |1.1.A.3b| | 1 |
| Exhaust mounting missing |7.1.1b| | 1 |