Most common failures | No# failures |
---|
Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 95 |
Windscreen wiper does not clear the windscreen effectively | 78 |
Headlamp aim out of alignment | 50 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 48 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 47 |
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 44 |
Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 38 |
Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 29 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 29 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 27 |
Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 23 |
Brakes imbalanced across an axle | 23 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 21 |
Registration plate lamp issues | 21 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 21 |
Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 21 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 20 |
Registration plate issues | 18 |
Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 17 |
Brake pipe excessively corroded | 15 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 14 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 13 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 12 |
Emissions not tested (8.2.1.2 (d)) | 12 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 12 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 11 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 10 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 10 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 10 |
Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 9 |
Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 8 |
Electronic stability control warning lamp indicates a fault (7.12 (e)) | 8 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 8 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 8 |
Nearside Front Anti-roll bar linkage fractured |2.4.G.1| | 8 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 8 |
Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 8 |
Anti-lock braking system warning lamp indicates an ABS fault | 7 |
Offside Front Anti-roll bar linkage fractured |2.4.G.1| | 7 |
Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 7 |
Brake hose excessively deteriorated | 7 |
Nearside Side repeater not working (4.4.1 (a) (ii)) | 6 |
Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 6 |
Brake performance not tested (1.2.1 (g)) | 6 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 6 |
Windscreen washer not working | 6 |
Headlamp levelling device inoperative (4.1.5 (a)) | 6 |
Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 6 |
Offside Front Shock absorbers has a serious fluid leak | 6 |
Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 5 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 5 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 5 |
Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 5 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
Nearside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 5 |
Offside Rear coil spring broken |2.4.C.1a| | 5 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 5 |
Nearside Front Shock absorbers has a serious fluid leak | 5 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
Offside Front Road wheel fixing missing (5.2.1 (a) (i)) | 4 |
Offside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 4 |
Power steering malfunctioning (2.1.5 (a)) | 4 |
Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 4 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 4 |
Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 4 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 4 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 4 |
Rear brake disc in such a condition that it is seriously weakened | 4 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
Nearside Rear Shock absorbers has a serious fluid leak | 4 |
Engine MIL inoperative or indicates a malfunction (8.2.2.2 (g)) | 3 |
Nearside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 3 |
Nearside Front Road wheel fixing missing (5.2.1 (a) (i)) | 3 |
Nearside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 3 |
Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 3 |
Offside Front Anti-roll bar linkage insecure |2.4.G.1| | 3 |
Offside Rear Anti-roll bar linkage insecure |2.4.G.1| | 3 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 3 |
Power steering inoperative and steering adversely affected (2.1.5 (c) (ii)) | 3 |
Offside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 3 |
Nearside Front Anti-roll bar linkage attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 3 |
Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 3 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 3 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 3 |
Offside Parking brake inoperative on one side (1.4.1 (a)) | 3 |
Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 3 |
Offside Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 3 |
Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 3 |
Offside Rear Anti-roll bar linkage fractured |2.4.G.1| | 3 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 3 |
Offside Front Valve stem seriously damaged (5.2.3 (j)) | 3 |
Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 3 |
Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
Battery insecure |1.9.1| | 3 |
Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 3 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 2 |
Offside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 2 |
Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
Offside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 2 |
Nearside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 2 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
Parking brake lever has no reserve travel |3.1.6b| | 2 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 2 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
Central Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
Headlamp aim not tested (4.1.2 (b)) | 2 |
Exhaust catalytic converter missing where one was fitted as standard (8.2.2.1 (a)) | 2 |
Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
Electronic power steering not working (2.6 (c)) | 2 |
Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
Offside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 2 |
Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 2 |
Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Offside Front Service brake lagging in operation (1.2.1 (d)) | 2 |
Offside Side repeater not working (4.4.1 (a) (ii)) | 2 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Brake pedal has insufficient reserve travel (1.1.2 (a)) | 2 |
Exhaust emits clearly visible black smoke during acceleration (8.2.1.2 (g)) | 2 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
Offside Rear coil spring fractured |2.4.C.1a| | 2 |
Offside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 2 |
Nearside Rear Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
Nearside Rear coil spring broken |2.4.C.1a| | 2 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Nearside Front Valve stem seriously damaged (5.2.3 (j)) | 2 |
Nearside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Nearside Rear Valve stem seriously damaged (5.2.3 (j)) | 2 |
Offside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Windscreen has damage | 2 |
Exhaust emits dense blue smoke at idle (8.2.1.2 (f)) | 2 |
Nearside Front Side repeater not working |1.4.A.2c| | 2 |
Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a)) | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
Nearside Rear Stop lamp not working |1.2.1b| | 2 |
Rear brake binding | 2 |
Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
Offside Side repeater not working |1.4.A.2c| | 2 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 2 |
Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 2 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 2 |
Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 2 |
Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 2 |
Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 2 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back (5.3.6 (a) (i)) | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back (5.3.6 (a) (i)) | 2 |
Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
Front brake application uneven | 2 |