| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 5172 |
| Headlamp aim out of alignment | 4375 |
| Registration plate lamp issues | 3323 |
| Brake pipe excessively corroded | 2384 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1797 |
| Brakes imbalanced across an axle | 1794 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1629 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1300 |
| Rear parking brake recording little or no effort | 1182 |
| Parking brake: efficiency below requirements |3.7.B.7| | 1165 |
| Registration plate issues | 1045 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 691 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 617 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 556 |
| Parking brake lever has no reserve travel |3.1.6b| | 540 |
| Rear brake binding | 540 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 518 |
| Offside front brake binding |3.7.B.1| | 518 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 496 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 484 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 467 |
| Rear brake disc in such a condition that it is seriously weakened | 455 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 448 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 416 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 389 |
| Front brake application uneven | 384 |
| Offside Rear coil spring broken |2.4.C.1a| | 381 |
| Nearside Rear coil spring broken |2.4.C.1a| | 379 |
| Offside Front front brake binding |3.7.B.1| | 355 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 351 |
| Front brake disc in such a condition that it is seriously weakened | 349 |
| Nearside front brake binding |3.7.B.1| | 313 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 285 |
| Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 283 |
| Nearside Rear brake caliper leaking |3.6.A.1| | 283 |
| Offside Stop lamp not working |1.2.1b| | 281 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 280 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 277 |
| Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 275 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 272 |
| Offside Rear brake caliper leaking |3.6.A.1| | 259 |
| Nearside Stop lamp not working |1.2.1b| | 250 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 238 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 236 |
| Offside Front brake disc excessively pitted |3.5.1h| | 229 |
| Nearside Front coil spring broken |2.4.C.1a| | 229 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 228 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 227 |
| Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 220 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 207 |
| Nearside Front front brake binding |3.7.B.1| | 207 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 196 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 193 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 192 |
| Mechanical brake component has restricted free movement | 178 |
| Windscreen washer not working | 175 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 169 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 166 |
| Service brake: efficiency below requirements |3.7.B.7| | 162 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 157 |
| Offside Front coil spring broken |2.4.C.1a| | 154 |
| Offside Front Position lamp not working |4.2.1 |a|| | 152 |
| Offside Rear Braking system leaking |3.6.A.1| | 149 |
| Brake hose excessively deteriorated | 147 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 143 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 137 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 137 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 133 |
| Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 133 |
| Rear brake application uneven | 131 |
| Nearside Rear Braking system leaking |3.6.A.1| | 131 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 130 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 129 |
| Front brake disc excessively pitted |3.5.1h| | 128 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 124 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 121 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 119 |
| Offside Rear Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 118 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 118 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 115 |
| Front position lamp|s| not working |1.1.A.3b| | 115 |
| Centre Stop lamp not working |1.2.1b| | 113 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 112 |
| Offside Rear Coil spring fractured or broken |5.3.1 |b| |i|| | 112 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 110 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 110 |
| Offside Rear brake disc excessively pitted |3.5.1h| | 109 |
| Nearside Rear brake disc excessively pitted |3.5.1h| | 108 |
| Front brake excessively fluctuating | 107 |
| Windscreen has damage | 106 |
| Nearside Rear coil spring fractured |2.4.C.1a| | 105 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 105 |
| Windscreen wiper blade insecure | 103 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 103 |
| Offside Rear Stop lamp not working |1.2.1b| | 102 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 100 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 100 |
| Nearside Rear Coil spring fractured or broken |5.3.1 |b| |i|| | 99 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 98 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 98 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 98 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 98 |
| Nearside Rear Stop lamp not working |1.2.1b| | 97 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 97 |
| Offside Rear coil spring fractured |2.4.C.1a| | 96 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 96 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 96 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 95 |
| Emissions not tested (8.2.1.2 (d)) | 94 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 94 |
| Offside Front Anti-roll bar linkage insecure |2.4.G.1| | 90 |
| Supplementary Restraint System warning lamp indicates a fault |5.4.2| | 89 |
| Offside Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 89 |
| Brake fluid warning lamp illuminated |3.6.G.2| | 88 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 87 |
| Rear Mechanical brake component has restricted free movement | 86 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 86 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 85 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 85 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 85 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 84 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 83 |
| Nearside Outer Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 83 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 82 |
| Offside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 81 |
| Battery insecure |1.9.1| | 80 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 79 |
| Horn not working (7.7 (a)) | 78 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 77 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 76 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 76 |
| Horn not working |1.6.2a| | 74 |
| Nearside Front Coil spring fractured or broken |5.3.1 |b| |i|| | 74 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 74 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 72 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 72 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 71 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 69 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 69 |
| Nearside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 68 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 67 |
| Offside Outer Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 67 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 66 |
| Nearside Front Service brake excessively binding |1.2.1 |f|| | 66 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 65 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 65 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 64 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 64 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 63 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 62 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 62 |
| Rear brake disc excessively pitted |3.5.1h| | 61 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 61 |
| Nearside Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 61 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 60 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 59 |
| Power steering pipe|s| or hose|s| leaking |2.3.3b| | 59 |
| Offside Rear fog lamp not working |1.3.2b| | 59 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 58 |
| Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 57 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 56 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 56 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 55 |
| Emissions not tested |7.0| | 55 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 55 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 55 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 54 |
| Nearside Rear coil spring incomplete |2.4.C.1a| | 54 |
| Emissions not tested |7.3.A.1| | 52 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 52 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 52 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 52 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 51 |
| Brake performance not tested |3.7.A.1| | 50 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 50 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 50 |
| Offside Front Coil spring fractured or broken |5.3.1 |b| |i|| | 50 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 50 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 49 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 49 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 48 |
| Offside Front brake caliper has restricted free movement |3.5.1k| | 48 |
| Offside Front Anti-roll bar linkage fractured |2.4.G.1| | 47 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 47 |
| Nearside Side repeater not working |1.4.A.2c| | 46 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 46 |
| Emissions unable to be completed (8.2.1.2 (d)) | 46 |
| rear parking |secondary| brakes imbalanced | 46 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 45 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 45 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 45 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 45 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 45 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 44 |
| Nearside Front coil spring fractured |2.4.C.1a| | 44 |
| Offside Rear coil spring incomplete |2.4.C.1a| | 43 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 43 |
| Offside Side repeater not working |1.4.A.2c| | 43 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 42 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 42 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 42 |
| Nearside Front Anti-roll bar linkage fractured |2.4.G.1| | 41 |
| Brake hose damaged | 41 |
| Brake performance not tested (1.2.1 (g)) | 41 |
| Nearside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 40 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 40 |
| Nearside Rear Hydraulic brake calliper leaking |1.1.16 |b| |i|| | 40 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 39 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 39 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 39 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 39 |
| Rear fog lamp not working |1.3.2b| | 39 |
| Nearside Headlamp not working on main beam |1.7.5a| | 38 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 38 |
| Offside Parking brake inoperative on one side |1.4.1 |a|| | 38 |
| Nearside Rear Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 38 |
| Offside front brake juddering severely |3.7.A.2b| | 38 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 38 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 38 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 38 |
| Offside Headlamp not working on main beam |1.7.5a| | 38 |
| Nearside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 38 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 38 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 37 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 37 |
| Nearside Rear Anti-roll bar linkage insecure |2.4.G.1| | 37 |
| Nearside Parking brake inoperative on one side |1.4.1 |a|| | 37 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 37 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 37 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 36 |
| Offside Rear Anti-roll bar linkage insecure |2.4.G.1| | 36 |
| Rear fog lamp tell tale not working |1.3.1b| | 36 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 36 |
| Nearside Front All position lamps not working |1.1.A.3b| | 36 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 35 |
| brake disc excessively pitted |3.5.1h| | 35 |
| Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 35 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 34 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 34 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 34 |
| Offside Rear Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 33 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 33 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 33 |
| Offside Rear Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 33 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 33 |
| front brakes release unevenly |3.7.B.4| | 33 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 33 |
| Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 33 |
| Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 33 |
| Offside Rear Hydraulic brake calliper leaking |1.1.16 |b| |i|| | 33 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 33 |
| Offside Rear Parking brake inoperative on one side |1.4.1 |a|| | 33 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 33 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 32 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 32 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 32 |
| Power steering component|s| leaking |2.3.3b| | 32 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 32 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 31 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 31 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 31 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 31 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 31 |
| Offside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 31 |
| Nearside front brake juddering severely |3.7.A.2b| | 30 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 30 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 30 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 30 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 30 |
| Drivers airbag missing (7.1.5 (a)) | 30 |
| Nearside rear brake excessively fluctuating |3.7.B.3| | 30 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 30 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 30 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 30 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 30 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 30 |
| Offside Front brake disc excessively scored |3.5.1h| | 29 |
| Power steering component leaking (2.1.5 (a)) | 29 |
| Offside Rear Anti-roll bar linkage fractured |2.4.G.1| | 29 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 29 |
| Offside Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 29 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 29 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 29 |
| Offside rear brake excessively fluctuating |3.7.B.3| | 29 |
| Front Front position lamp|s| not working |1.1.A.3b| | 29 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 29 |
| Offside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 29 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 28 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 28 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 28 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 28 |
| Stop lamp not working |1.2.1b| | 28 |
| Emissions not tested |8.2.1.2 |d|| | 28 |
| Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 28 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 28 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 28 |
| Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 27 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 27 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 27 |
| Offside Steering rack gaiter split |2.2.D.2d| | 27 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 27 |
| Offside Rear Braking system leaking caliper |3.6.A.1| | 27 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 27 |
| Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 27 |
| Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 27 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 27 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 26 |
| Supplementary restraint system warning lamp indicates a fault |7.1.6 |a|| | 26 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 26 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 26 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 26 |
| Offside Front All position lamps not working |1.1.A.3b| | 26 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 26 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 26 |
| Anti-lock braking system warning lamp does not illuminate (1.6 (a)) | 26 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 26 |
| Central Stop lamp not working |1.2.1b| | 26 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 26 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 26 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 26 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 26 |
| Brake pedal spongy |3.3.B.1b| | 26 |
| Nearside Front position lamp|s| incorrect colour |1.1.A.3e| | 26 |
| Nearside Front brake disc excessively scored |3.5.1h| | 25 |
| Offside Rear Upper Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 25 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 25 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 25 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 25 |
| Brake hose has insufficient room to move | 25 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 25 |
| Power steering inoperative |2.3.3a| | 25 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 25 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 24 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 24 |
| Nearside Front Shock absorbers has a serious fluid leak | 24 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 24 |
| Braking system leaking |3.6.A.1| | 24 |
| Offside Inner Front brake disc excessively pitted |3.5.1h| | 24 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 24 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 24 |
| Offside Front Wheel nut|s| missing |4.2.A.1e| | 24 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 24 |
| Horn not working (7.7 (a) (ii)) | 24 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 24 |
| Centre Rear Stop lamp not working |1.2.1b| | 24 |
| Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 24 |
| Offside Front Shock absorbers has a serious fluid leak | 23 |
| Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 23 |
| Nearside Inner Front brake disc excessively pitted |3.5.1h| | 23 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 23 |
| Offside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 23 |
| Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 23 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 23 |
| Power steering pipe/hose leaking |2.1.5 |a|| | 23 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 23 |
| Nearside Rear brake disc excessively scored |3.5.1h| | 22 |
| Nearside Rear Anti-roll bar linkage fractured |2.4.G.1| | 22 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 22 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 22 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 22 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 22 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 22 |
| Offside Rear Lower Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 22 |
| Nearside Rear Braking system leaking caliper |3.6.A.1| | 22 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 22 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 22 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 22 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 21 |
| Offside Front Position lamp not working |4.2.1 |a| |ii|| | 21 |
| Offside Front coil spring fractured |2.4.C.1a| | 21 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 21 |
| Offside Rear Upper Suspension arm corroded and seriously weakened |2.4.G.1| | 21 |
| Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 21 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 21 |
| Nearside Front Service brake lagging in operation (1.2.1 (d)) | 21 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 21 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 21 |
| Offside Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 21 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 21 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 21 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 21 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 20 |
| Nearside Rear Shock absorbers has a serious fluid leak | 20 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 20 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 20 |
| Offside Rear Wheel nut|s| missing |4.2.A.1e| | 20 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 20 |
| Offside Rear Service brake excessively binding |1.2.1 |f|| | 20 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 20 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 20 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 20 |
| Nearside Front front brake juddering severely |3.7.A.2b| | 20 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 19 |
| Offside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 19 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 19 |
| Offside Rear rear brake excessively fluctuating |3.7.B.3| | 19 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 19 |
| Offside Rear Shock absorbers has a serious fluid leak | 19 |
| Offside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 19 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 19 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 19 |
| Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 19 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 19 |
| Nearside Front coil spring incomplete |2.4.C.1a| | 19 |
| Nearside Rear Valve stem seriously damaged |4.1.D.1e| | 19 |
| Offside Headlamp aim not tested |1.8.A.1c| | 19 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 18 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 18 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 18 |
| Exhaust emissions likely to be affected by an exhaust leak |8.2.1.1 |b|| | 18 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 18 |
| Nearside Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 18 |
| Central Exhaust has a major leak of exhaust gases |7.1.2| | 18 |
| Brake lever has insufficient reserve travel |1.1.2 |a|| | 18 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 18 |
| Nearside Rear Road wheel bead rim badly distorted |4.2.A.1a| | 18 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 18 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 18 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 18 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 18 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 17 |
| Offside Rear brake disc excessively scored |3.5.1h| | 17 |
| Nearside Rear Upper Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 17 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 17 |
| Rear Exhaust system not adequately supported |7.1.1| | 17 |
| Nearside Rear coil spring cracked |2.4.C.1a| | 17 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 17 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 17 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 17 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 17 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 17 |
| Nearside Front Road wheel bead rim badly distorted |4.2.A.1a| | 17 |
| Offside Front Side repeater not working |1.4.A.2c| | 17 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 17 |
| Windscreen wiper does not clear the windscreen effectively | 16 |
| Headlamp aim out of alignment | 16 |
| Front brake disc excessively scored |3.5.1h| | 16 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 16 |
| Offside Front Service brake lagging in operation (1.2.1 (d)) | 16 |
| Nearside Front brake caliper has restricted free movement |3.5.1k| | 16 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 16 |
| Front Service brake excessively fluctuating (1.2.1 (e)) | 16 |
| Offside Rear Braking system leaking brake caliper |3.6.A.1| | 16 |
| Nearside Rear front brake binding |3.7.B.1| | 16 |
| Offside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 16 |
| Offside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 16 |
| Offside rear brake juddering severely |3.7.A.5b| | 16 |
| Offside Front front brake juddering severely |3.7.A.2b| | 16 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 16 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 16 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 16 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 16 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 16 |
| Offside Headlamp insecure |1.7.3| | 16 |
| Nearside Headlamp aim not tested |1.8.A.1c| | 16 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 16 |
| Nearside Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 15 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 15 |
| Horn not working |7.7 |a| |ii|| | 15 |
| Nearside Front Power steering pipe/hose leaking (2.1.5 (a)) | 15 |
| Nearside Outer Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 15 |
| Offside Rear Valve stem seriously damaged |4.1.D.1e| | 15 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 15 |
| Rear Exhaust has a part missing |7.1.1a| | 15 |
| Offside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 15 |
| Nearside Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 15 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 15 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 15 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 15 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 15 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 15 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a)) | 15 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 15 |
| Offside Rear brake caliper has restricted free movement |3.5.1k| | 15 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 15 |
| Nearside Rear Wheel nut|s| missing |4.2.A.1e| | 15 |
| Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 15 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 15 |
| Nearside Rear Upper Suspension arm corroded and seriously weakened |2.4.G.1| | 15 |
| Offside Front An item not tested |Manual| | 15 |
| Power steering inoperative (2.1.5 (c) (i)) | 15 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 15 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 15 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 15 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 15 |
| Offside Rear Service brake excessively fluctuating |1.2.1 |e|| | 14 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 14 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 14 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 14 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 14 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 14 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 14 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 14 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 14 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 14 |
| Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 14 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 14 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 14 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 14 |
| Brake performance unable to be tested (1.2.1 (g)) | 14 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 14 |
| Offside Rear front brake binding |3.7.B.1| | 14 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 14 |
| Power steering fluid level below minimum |2.3.1| | 14 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 14 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 14 |
| Offside Rear Brake pipe leaking |3.6.A.1| | 14 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 14 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 14 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 14 |
| Parking brake: efficiency below requirements (3.7.B.7) | 14 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 14 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 14 |
| Nearside Headlamp insecure |1.7.3| | 14 |
| Rear Parking brake lever has no reserve travel |3.1.6b| | 14 |
| Nearside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 14 |
| Offside Front brake caliper leaking |3.6.A.1| | 14 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 14 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 14 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 14 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 14 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 14 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 14 |
| Brake pipe leaking |3.6.A.1| | 14 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 13 |
| Offside Rear coil spring cracked |2.4.C.1a| | 13 |
| Exhaust system not adequately supported |7.1.1| | 13 |
| Nearside Front Wheel nut|s| missing |4.2.A.1e| | 13 |
| Anti-lock braking system warning lamp does not illuminate |3.4.1b| | 13 |
| Nearside Rear Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 13 |
| Offside Rear Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 13 |
| Nearside Rear Valve stem seriously damaged (5.2.3 (j)) | 13 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 13 |
| Nearside Front Valve stem seriously damaged |4.1.D.1e| | 13 |
| Nearside Front Position lamp not working |4.2.1 |a| |ii|| | 13 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 13 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 13 |
| Front Windscreen wiper blade deteriorated |8.2.2| | 13 |
| Nearside Position lamp not working (4.2.1 (a) (ii)) | 13 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 13 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 13 |
| Offside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 13 |
| Nearside Front Side repeater not working |1.4.A.2c| | 13 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 12 |
| Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 12 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 12 |
| Exhaust catalytic converter missing where one was fitted as standard |7.1.3| | 12 |
| brake disc in such a condition that it is seriously weakened |3.5.1i| | 12 |
| Brake fluid significantly below minimum mark |1.1.10 |d| |ii|| | 12 |
| Central Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 12 |
| Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 12 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 12 |
| Offside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 12 |
| Offside Front Valve stem seriously damaged (5.2.3 (j)) | 12 |
| Offside Rear Valve stem seriously damaged (5.2.3 (j)) | 12 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 12 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 12 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 12 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 12 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 12 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 12 |
| rear brakes release unevenly |3.7.B.4| | 12 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 12 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 12 |
| Front front brake binding |3.7.B.1| | 12 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 12 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 12 |
| Offside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 12 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 12 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 12 |
| Offside Rear position lamp|s| incorrect colour |1.1.A.3e| | 12 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 12 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 12 |
| Nearside Front Brake hose twisted |3.6.B.4c| | 12 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 12 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
| Offside Front coil spring incomplete |2.4.C.1a| | 12 |
| Offside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 12 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 12 |
| Front position lamp|s| not working both |1.1.A.3b| | 12 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 12 |
| Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 12 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 12 |
| Nearside Rear Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 12 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 11 |
| Driver`s airbag obviously defective |5.4.1| | 11 |
| Direction indicators not working |1.4.A.2c| | 11 |
| Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 11 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 11 |
| Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 11 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 11 |
| Offside Rear rear brake juddering severely |3.7.A.5b| | 11 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 11 |
| Offside Front Road wheel fixing missing (5.2.1 (a) (i)) | 11 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 11 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 11 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 11 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 11 |
| Nearside Front Valve stem seriously damaged (5.2.3 (j)) | 11 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 11 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 11 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 11 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 11 |
| Nearside Rear rear brake excessively fluctuating |3.7.B.3| | 11 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 11 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 11 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 11 |
| Nearside rear brake juddering severely |3.7.A.5b| | 11 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 11 |
| Nearside Rear brake caliper has restricted free movement |3.5.1k| | 11 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 11 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 11 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 11 |
| Nearside Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 11 |
| Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 11 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 11 |
| Offside Rear Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 11 |
| Offside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 11 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 11 |
| Nearside Rear Braking system leaking brake caliper |3.6.A.1| | 11 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 11 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 11 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 11 |
| Rear Service brake excessively fluctuating (1.2.1 (e)) | 10 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor |5.3.6 |a| |i|| | 10 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 10 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 10 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 10 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 10 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 10 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 10 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 10 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 10 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 10 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 10 |
| Nearside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 10 |
| Nearside Front Brake hose excessively twisted (1.1.12 (b) (ii)) | 10 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 10 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 10 |
| Nearside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 10 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 10 |
| Windscreen wiper blade deteriorated |8.2.2| | 10 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 10 |
| Nearside Front Braking system leaking |3.6.A.1| | 10 |
| Nearside Side repeater missing |1.4.A.2b| | 10 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 10 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 10 |
| Offside Front Floor excessively deteriorated (6.2.4 (a) (i)) | 10 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 10 |
| Oil leaking excessively from engine |8.4.1 |a| |i|| | 10 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 10 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 10 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 10 |
| Rear fog lamp switch faulty |1.3.1a| | 10 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 10 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 10 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 10 |
| Nearside Rear Brake pipe leaking |3.6.A.1| | 10 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 10 |
| Offside Front Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 9 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 9 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 9 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis |2.4.A.3| | 9 |
| Offside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 9 |
| Brake performance not tested |1.2.1 |g|| | 9 |
| Nearside Rear Hydraulic brake calliper leaking and braking performance affected (1.1.16 (b) (ii)) | 9 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 9 |
| Offside Front Braking system leaking |3.6.A.1| | 9 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 9 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 9 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 9 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 9 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.D.1| | 9 |
| Nearside Front Headlamp insecure |1.7.3| | 9 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 9 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 9 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 9 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 9 |
| Offside Front Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 9 |
| Offside Headlamp aim not tested (4.1.2 (b)) | 9 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 9 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 9 |
| Nearside Front An item not tested |Manual| | 9 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 9 |
| Nearside Rear rear brake juddering severely |3.7.A.5b| | 9 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 9 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 9 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 9 |
| front brake juddering severely |3.7.A.2b| | 9 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 9 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 9 |
| Nearside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 9 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 9 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 9 |
| Central Stop lamp|s| not working |4.3.1 |a| |ii|| | 9 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 9 |
| Front Position lamp not working both (4.2.1 (a) (ii)) | 9 |
| Nearside Rear Upper Coil spring fractured or broken (5.3.1 (b) (i)) | 9 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 9 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 9 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 9 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 9 |
| Offside Front Service brake excessively fluctuating |1.2.1 |e|| | 9 |
| Offside Side repeater missing |1.4.A.2b| | 9 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.2.1 (a)) | 9 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 9 |
| Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 9 |
| Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 9 |
| Offside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 9 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 9 |
| Offside Rear Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 9 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 9 |
| Front Brake lining|s| less than 1.5 mm thick |3.5.1g| | 9 |
| Parking brake: efficiency below requirements |3.7.D.4| | 9 |
| Brake pipe excessively corroded | 8 |
| Horn not working (7.7 (a)) | 8 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 8 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Offside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 8 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 8 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 8 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 8 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 8 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 8 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 8 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 8 |
| Offside Outer Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 8 |
| Offside Rear Hydraulic brake calliper leaking and braking performance affected (1.1.16 (b) (ii)) | 8 |
| Offside Front Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 8 |
| Upper Stop lamp not working |1.2.1b| | 8 |
| Nearside Rear Position lamp not working |4.2.1 |a|| | 8 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 8 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 8 |
| Offside Front Valve stem seriously damaged |4.1.D.1e| | 8 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 8 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 8 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 8 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 8 |
| Rear Exhaust has a major leak of exhaust gases joint |7.1.2| | 8 |
| Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 8 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 8 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 8 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 8 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 8 |
| Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 8 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 8 |
| Offside Front Anti-roll bar linkage missing |2.4.G.1| | 8 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 8 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 8 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 8 |
| Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 8 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 8 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 8 |
| Nearside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 8 |
| Offside Headlamp levelling device inoperative (4.1.5 (a)) | 8 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| An item not tested |Manual| | 8 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 8 |
| Offside Front Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 8 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 8 |
| rear brake recording little or no effort |3.7.B.5a| | 8 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 8 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 8 |
| Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 8 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 8 |
| Offside Front Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 8 |
| Power steering pipe/hose excessively corroded (2.1.5 (g) (i)) | 8 |
| Nearside Front position lamp(s) not working (1.1.A.3b) | 8 |
| Headlamp levelling device inoperative (4.1.5 (a)) | 8 |
| Engine MIL inoperative or indicates a malfunction (8.2.2.2 (g)) | 8 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 8 |
| Hazard warning lamps inoperative (4.4.1 (e)) | 8 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 8 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 8 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail |5.3.6 |a| |i|| | 8 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 8 |
| Offside Front Service brake indicates brake bind |3.7.D.2a| | 8 |
| Horn sounds harsh or grating |1.6.2e| | 8 |
| Offside Rear Subframe mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 8 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 8 |
| Offside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 8 |
| Centre Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 8 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 8 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 8 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 8 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 7 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 7 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 7 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 7 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 7 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 7 |
| Offside Side repeater incorrect colour |1.4.A.2f| | 7 |
| Power steering malfunctioning |2.3.3a| | 7 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 7 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail |5.3.6 |a| |i|| | 7 |
| Central Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 7 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 7 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 7 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 7 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 7 |
| Offside Rear Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 7 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Nearside Front Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 7 |
| Offside Rear Upper Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 7 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 7 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 7 |
| Rear Service brake excessively fluctuating |1.2.1 |e|| | 7 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 7 |
| Nearside Front Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 7 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 7 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 7 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 7 |
| Nearside Rear Service brake excessively fluctuating |1.2.1 |e|| | 7 |
| Nearside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 7 |
| Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 7 |
| Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 7 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 7 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 7 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 7 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 7 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 7 |
| Front Position lamp not working (4.2.1 (a) (ii)) | 7 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 7 |
| Exhaust has a part missing |7.1.1a| | 7 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 7 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 7 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 7 |
| Nearside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 7 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 7 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 7 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 7 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| rear brake excessively fluctuating |3.7.B.3| | 7 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 7 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 7 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 7 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 7 |
| Power steering fluid reservoir empty (2.1.5 (b) (ii)) | 7 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 7 |
| Offside Rear Hydraulic brake calliper leaking and braking performance affected |1.1.16 |b| |ii|| | 7 |
| Offside Rear Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 7 |
| Nearside Front Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 7 |
| Offside Outer Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 7 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 7 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 7 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 7 |
| Engine MIL inoperative or indicates a malfunction |8.2.2.2 |g|| | 7 |
| Nearside Rear Hydraulic brake calliper leaking and braking performance affected |1.1.16 |b| |ii|| | 7 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 7 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 7 |
| Front All position lamps not working |1.1.A.3b| | 7 |
| Nearside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 7 |
| Fuel cap/sealing device missing |7.2.4a| | 7 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 7 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 7 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 7 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 7 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 7 |
| Hazard warning switch inoperative (4.4.2 (a) (ii)) | 7 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 7 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 7 |
| Rear brake disc excessively scored |3.5.1h| | 7 |
| Rear Exhaust emissions likely to be affected by an exhaust leak |8.2.1.1 |b|| | 7 |
| Nearside Front Front position lamp|s| incorrect colour |1.1.A.3e| | 7 |
| Offside Front Front position lamp|s| incorrect colour |1.1.A.3e| | 7 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 7 |
| Offside Front Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 7 |
| Brakes imbalanced across an axle | 6 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 6 |
| Rear Rear fog lamp not working |1.3.2b| | 6 |
| Offside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 6 |
| Offside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| Offside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 6 |
| Nearside Side repeater incorrect colour |1.4.A.2f| | 6 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 6 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 6 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 6 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 6 |
| Nearside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 6 |
| Nearside Front Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 6 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 6 |
| Nearside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 6 |
| Offside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 6 |
| Offside Front Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 6 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 6 |
| Offside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 6 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 6 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 6 |
| Nearside Headlamp not working on main beam |4.1.1 |a| |ii|| | 6 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail (5.3.6 (a) (i)) | 6 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 6 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 6 |
| Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 6 |
| Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 6 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 6 |
| Rear fog lamp emits a light other than red |1.3.2e| | 6 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch |5.2.6| | 6 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 6 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 6 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 6 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 6 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 6 |
| Offside Front Brake hose twisted |3.6.B.4c| | 6 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 6 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 6 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 6 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 6 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 6 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 6 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 6 |
| Nearside Rear Anti-roll bar ball joint excessively worn |5.3.4 |a| |i|| | 6 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 6 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| front brake binding |3.7.B.1| | 6 |
| Offside Front position lamp(s) not working (1.1.A.3b) | 6 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 6 |
| Rear Exhaust has a major leak of exhaust gases box (6.1.2 (a)) | 6 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 6 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 6 |
| Nearside Direction indicators not working |1.4.A.2c| | 6 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 6 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 6 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 6 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 6 |
| Brake pedal has insufficient reserve travel |1.1.2 |a|| | 6 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 6 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 6 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 6 |
| Nearside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 6 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 6 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 6 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 6 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill |6.2.2 |d| |i|| | 6 |
| Nearside All position lamps not working |1.1.A.3b| | 6 |
| Rear Stop lamp not working |1.2.1b| | 6 |
| Rear Exhaust has a major leak of exhaust gases silencer |7.1.2| | 6 |
| Exhaust system insecure (6.1.2 (a)) | 6 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 6 |
| Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 6 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 6 |
| Offside Headlamp insecure (4.1.1 (c)) | 6 |
| Nearside Outer Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 6 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 6 |
| Rear Exhaust system insecure (6.1.2 (a)) | 6 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 6 |
| Offside Position lamp not working (4.2.1 (a) (ii)) | 6 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 6 |
| Nearside Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 6 |
| Offside front brake grabbing severely |3.7.A.2b| | 6 |
| Front front brake juddering severely |3.7.A.2b| | 6 |
| Offside Front Service brake grabbing severely (1.2.1 (c)) | 6 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 6 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 6 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 6 |
| Nearside Body has a sharp edge caused by damage |6.1.C.1| | 6 |
| Exhaust carbon monoxide content at idle exceeds default limits |8.2.1.2 |b|| | 6 |
| Wheel nut|s| missing |4.2.A.1e| | 6 |
| Offside Rear Upper Coil spring fractured or broken (5.3.1 (b) (i)) | 6 |
| Front position lamp|s| incorrect colour |1.1.A.3e| | 6 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 6 |
| Rear brake excessively fluctuating | 6 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 6 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 6 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 6 |
| Offside Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 6 |
| Centre Rear Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 6 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 6 |
| Nearside Headlamp light intensity severely reduced |4.1.4 |a|| | 6 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 6 |
| Offside Front Brake hose excessively damaged |3.6.B.4d| | 6 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 6 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 6 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 6 |
| Power steering component leaking |2.1.5 |a|| | 6 |
| Nearside Rear Upper Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 6 |
| Power steering malfunctioning (2.1.5 (a)) | 6 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 6 |
| Nearside Rear Anti-roll bar linkage missing |2.4.G.1| | 6 |
| Nearside Front Headlamp aim not tested |1.8.A.1c| | 6 |
| Offside brake disc in such a condition that it is seriously weakened |3.5.1i| | 5 |
| Nearside Front Direction indicators incorrect colour |1.4.A.2f| | 5 |
| Offside Rear Parking |secondary brake| on a single line braking system has inadequate effort at a wheel |1.3.1 |a| |i|| | 5 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 5 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
| Front Power steering pipe/hose leaking |2.1.5 |a|| | 5 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis |6.1.1 |c| |i|| | 5 |
| Registration plate lamp issues | 5 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 5 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 5 |
| Nearside Rear Outer Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 5 |
| Rear Service brake excessively binding (1.2.1 (f)) | 5 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 5 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 5 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 5 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 5 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner and outer sill |2.4.A.3| | 5 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 5 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 5 |
| Nearside Front Brake hose excessively twisted |1.1.12 |b| |ii|| | 5 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 5 |
| Rear Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 5 |
| Nearside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 5 |
| Offside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Nearside Front Position lamp light intensity significantly reduced |4.2.3 |a| |ii|| | 5 |
| Offside Front Position lamp light intensity significantly reduced |4.2.3 |a| |ii|| | 5 |
| Central Rear Stop lamp not working |1.2.1b| | 5 |
| Nearside Front Upper Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 5 |
| Nearside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Headlamp aim not tested |1.8.A.1c| | 5 |
| Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 5 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg (5.3.6 (a) (i)) | 5 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 5 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 5 |
| Offside Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened (5.3.1 (b) (i)) | 5 |
| Offside Front Brake hose leaking |3.6.A.1| | 5 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Rear Upper coil spring broken |2.4.C.1a| | 5 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch (7.1.1 (a) (i)) | 5 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch (7.1.1 (a) (i)) | 5 |
| Nearside Front coil spring cracked |2.4.C.1a| | 5 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 5 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 5 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 5 |
| Offside Rear An item not tested |Manual| | 5 |
| Offside Rear Road wheel bead rim badly distorted |4.2.A.1a| | 5 |
| Offside Front Direction indicator not working |1.4.A.2c| | 5 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 5 |
| Nearside Front Floor excessively deteriorated (6.2.4 (a) (i)) | 5 |
| Offside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 5 |
| Nearside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 5 |
| Offside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 5 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 5 |
| Central Rear Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 5 |
| Offside Rear Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 5 |
| Offside Rear Brake pipe at imminent risk of failure or fracture (1.1.11 (a)) | 5 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 5 |
| Nearside Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 5 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 5 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 5 |
| Offside Body has a sharp edge caused by damage |6.1.C.1| | 5 |
| Offside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Offside Front Suspension arm corroded and seriously weakened |2.4.G.1| | 5 |
| Offside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 5 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 5 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 5 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 5 |
| Nearside Front brake caliper leaking |3.6.A.1| | 5 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 5 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 5 |
| Nearside Front Service brake indicates brake bind |3.7.D.2a| | 5 |
| Nearside Rear Upper coil spring broken |2.4.C.1a| | 5 |
| Nearside Side repeater incorrect colour (4.4.3 (a)) | 5 |
| Offside Side repeater incorrect colour (4.4.3 (a)) | 5 |
| Offside Front Tie bar/rod fractured |2.4.G.1| | 5 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 5 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 5 |
| Nearside Rear Brake hose excessively damaged |3.6.B.4d| | 5 |
| Offside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 5 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 5 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch |7.1.1 |a| |i|| | 5 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 5 |
| Nearside brake disc excessively pitted |3.5.1h| | 5 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 5 |
| Offside Front Anti-roll bar insecure |2.4.G.1| | 5 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 5 |
| Offside Front Anti-roll bar linkage fractured |5.3.3 |b| |ii|| | 5 |
| Offside Front Front position lamp(s) not working (1.1.A.3b) | 5 |
| Nearside Rear position lamp|s| incorrect colour |1.1.A.3e| | 5 |
| Offside Rear Position lamp not working |4.2.1 |a|| | 5 |
| Nearside Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 5 |
| All direction indicators not working (4.4.1 (a) (ii)) | 5 |
| Offside Front Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 5 |
| Nearside Rear Parking |secondary brake| on a single line braking system has inadequate effort at a wheel |1.3.1 |a| |i|| | 5 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 5 |
| Nearside Front Anti-roll bar linkage fractured |5.3.3 |b| |ii|| | 5 |
| Offside Front Headlamp insecure |1.7.3| | 5 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 5 |
| Nearside Front Service brake lagging in operation |1.2.1 |d|| | 5 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 5 |
| Nearside Rear Direction indicators not working |1.4.A.2c| | 5 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 5 |
| Offside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 5 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mounting |2.4.A.3| | 5 |
| Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 5 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 5 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 5 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 5 |
| Nearside Front Road wheel fixing missing (5.2.1 (a) (i)) | 5 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 5 |
| Offside Rear Service brake lagging in operation (1.2.1 (d)) | 5 |
| Nearside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 5 |
| Nearside front brake grabbing severely |3.7.A.2b| | 5 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 5 |
| Offside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 5 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded (7.1.1 (a) (i)) | 5 |
| Offside Rear Anti-roll bar linkage missing |2.4.G.1| | 5 |
| brake disc excessively scored |3.5.1h| | 5 |
| Hazard warning lamps inoperative |1.4.B.1b| | 5 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 5 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 5 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 5 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Front Bumper insecure (6.1.4 (a) (i)) | 5 |
| Offside Position lamp not working |4.2.1 |a|| | 5 |
| Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 5 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan (5.3.6 (a) (i)) | 5 |
| Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 5 |
| Brake pipe leaking on a hydraulic braking system front to rear |1.1.11 |b| |ii|| | 5 |
| Offside Rear fog lamp missing |1.3.2a| | 5 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 5 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Front Brake hose excessively twisted |1.1.12 |b| |ii|| | 5 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 5 |
| Offside Front Headlamp aim not tested |1.8.A.1c| | 5 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 5 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 5 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 5 |
| Windscreen wiper not working |3.4 |a|| | 5 |
| Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 5 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 5 |
| Nearside Rear Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 5 |
| Nearside Front brake disc has restricted free movement |3.5.1j| | 5 |
| Nearside Windscreen wiper not operating automatically when switched on |8.2.1b| | 5 |
| Offside Windscreen wiper not operating automatically when switched on |8.2.1b| | 5 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 5 |
| Power steering inoperative and steering adversely affected (2.1.5 (c) (ii)) | 5 |
| Rear rear brake excessively fluctuating |3.7.B.3| | 5 |
| Rear fog lamp switch inoperative |4.5.3 |a| |ii|| | 5 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 5 |
| Rear fog lamp not working |1.3.2b| | 4 |
| Registration plate issues | 4 |
| Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 4 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 4 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 4 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 4 |
| Nearside Front Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 4 |
| Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 4 |
| Nearside Front Brake hose stretched |found during steering lock to lock check| |2.2.D.2b| | 4 |
| Nearside Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 4 |
| Offside Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 4 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 4 |
| Nearside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 4 |
| Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 4 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 4 |
| Offside Rear Valve stem seriously damaged |5.2.3 |j|| | 4 |
| Offside front brake recording little or no effort |3.7.B.5a| | 4 |
| Nearside Front Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 4 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner and outer sill |2.4.A.3| | 4 |
| Centre Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 4 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 4 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch (6.2.2 (d) (i)) | 4 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan (7.1.1 (a) (i)) | 4 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 4 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 4 |
| Nearside Front Anti-roll bar ball joint likely to become detached |5.3.4 |a| |ii|| | 4 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 4 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 4 |
| Brake master cylinder fluid level below minimum level |3.6.G.1e| | 4 |
| Brake fluid contaminated |1.8 |a|| | 4 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 4 |
| Nearside Rear Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 4 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 4 |
| Central Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 4 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 4 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 4 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 4 |
| Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Offside Outer Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 4 |
| Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 4 |
| Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 4 |
| Nearside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 4 |
| Nearside Front Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 4 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 4 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 4 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 4 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 4 |
| Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Nearside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 4 |
| Nearside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 4 |
| Nearside Front Headlamp not working on main beam |4.1.1 |a| |ii|| | 4 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 4 |
| Nearside Inner Rear brake disc excessively pitted |3.5.1h| | 4 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 4 |
| Offside Rear Brake pipe leaking on an air braking system (1.1.11 (b) (i)) | 4 |
| Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Horn sound not in accordance with requirements (7.7 (c)) | 4 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 4 |
| Undertray likely to become detached |6.2.1 |a| |ii|| | 4 |
| Offside Rear Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 4 |
| Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 4 |
| Nearside Rear Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 4 |
| Offside Front Anti-roll bar ball joint excessively worn |5.3.4 |a| |i|| | 4 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 4 |
| Offside Front Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 4 |
| Nearside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Rear fog lamp tell-tale not working |4.9.1 |a| |ii|| | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 4 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 4 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 4 |
| Emissions not tested exhaust blowing (8.2.1.2 (d)) | 4 |
| Inner Front brake disc excessively pitted |3.5.1h| | 4 |
| Rear Exhaust system insecure |6.1.2 |a|| | 4 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 4 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 4 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 4 |
| Offside Front Headlamp aim not tested (4.1.2 (b)) | 4 |
| Nearside Front Brake hose excessively damaged |3.6.B.4d| | 4 |
| Front Front position lamp|s| incorrect colour |1.1.A.3e| | 4 |
| rear brake juddering severely |3.7.A.5b| | 4 |
| Brake pipe leaking front to rear |3.6.A.1| | 4 |
| Main beam tell-tale not working (4.9.1 (a) (ii)) | 4 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 4 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Offside Headlamp aim not tested |4.1.2 |b|| | 4 |
| Offside Obligatory mirror missing |8.1.1| | 4 |
| Exhaust system insecure |6.1.2 |a|| | 4 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 4 |
| Offside Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 4 |
| Front Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 4 |
| Nearside Front Anti-roll bar insecure |2.4.G.1| | 4 |
| Stop lamp not working all |1.2.1b| | 4 |
| Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen |3.5 |a|| | 4 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 4 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 4 |
| Offside Rear Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 4 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch area |5.2.6| | 4 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis (5.3.6 (a) (ii)) | 4 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded under sill |5.2.6| | 4 |
| Front Power steering pipe/hose leaking (2.1.5 (a)) | 4 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 4 |
| Offside Front Headlamp not working on main beam |4.1.1 |a| |ii|| | 4 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 4 |
| Nearside Front front brakes release unevenly |3.7.B.4| | 4 |
| Nearside Front All position lamps not working |4.2.1 |a|| | 4 |
| Nearside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
| Driver`s airbag missing |5.4.1| | 4 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 4 |
| Nearside Headlamp insecure (4.1.1 (c)) | 4 |
| Offside Rear Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 4 |
| Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 4 |
| Fuel tank leaking |7.2.3| | 4 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 4 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 4 |
| Offside Rear Anti-roll bar insecure |2.4.G.1| | 4 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 4 |
| Headlamp aim beam image obviously incorrect |1.8.A.1b| | 4 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 4 |
| Offside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 4 |
| Offside Front Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 4 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 4 |
| Nearside Rear Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 4 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 4 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 4 |
| Nearside Front Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 4 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 4 |
| Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 4 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 4 |
| Nearside Rear coil spring corroded so that its cross sectional area is reduced and seriously weakened |2.4.C.1b| | 4 |
| Offside Rear coil spring corroded so that its cross sectional area is reduced and seriously weakened |2.4.C.1b| | 4 |
| Nearside Front Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 4 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 4 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 4 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 4 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 4 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 4 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 4 |
| Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 4 |
| Nearside Front Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 4 |
| Offside Rear brake disc contaminated by brake fluid |3.5.1h| | 4 |
| Nearside Rear Wheel nut|s| loose |4.2.A.1e| | 4 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 4 |
| Offside Rear Front position lamp|s| not working |1.1.A.3b| | 4 |
| Offside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 4 |
| Nearside Front Steering locking device missing |2.2.C.1g| | 4 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 4 |
| Offside Steering locking device missing |2.2.C.1g| | 4 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 4 |
| Offside Rear Braking system leaking Caliper |3.6.A.1| | 4 |
| Main beam `tell-tale` not working |1.7.4c| | 4 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill |7.1.1 |a| |i|| | 4 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 4 |
| Nearside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Service brake: efficiency below requirements |3.7.C.1a| | 4 |
| Stop lamp|s| all not working |4.3.1 |a| |iii|| | 4 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch |5.2.6| | 4 |
| Offside Front Anti-roll bar linkage insecure and impairing directional stability |5.3.3 |a| |ii|| | 4 |
| Offside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 4 |
| Nearside Front Anti-roll bar fractured |2.4.G.1| | 4 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
| Offside Rear Brake disc contaminated (1.1.14 (b)) | 4 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 4 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 4 |
| Offside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 4 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 4 |
| Parking brake inoperative on one side (1.4.1 (a)) | 4 |
| Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 4 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 4 |
| Brake pipe leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) | 4 |
| Front Body has a sharp edge caused by damage |6.1.C.1| | 4 |
| Offside Front front brake grabbing severely |3.7.A.2b| | 4 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SILL (7.1.1 (a) (i)) | 4 |
| Nearside Headlamp aim not tested |4.1.2 |b|| | 4 |
| Offside Front All position lamps not working |4.2.1 |a|| | 4 |
| Offside Front front brake recording little or no effort |3.7.B.5a| | 4 |
| Offside Front Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 4 |
| Nearside Front Front position lamp|s| not working side light |1.1.A.3b| | 4 |
| Nearside Front position lamp|s| not working side light |1.1.A.3b| | 4 |
| Brake hydraulic reservoir fluid level significantly below minimum level |1.1.10 |d| |ii|| | 4 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 4 |
| Offside Front Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 4 |
| Nearside Outer Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Offside Rear Braking system leaking calliper |3.6.A.1| | 4 |
| Offside Front position lamp|s| not working side light |1.1.A.3b| | 4 |
| Offside Rear Floor excessively deteriorated (6.2.4 (a) (i)) | 4 |
| Offside Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 4 |
| Power steering pipe/hose excessively corroded |2.1.5 |g| |i|| | 4 |
| Nearside Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 4 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Exhaust catalytic converter obviously modified (8.2.1.1 (a)) | 4 |
| Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 4 |
| Nearside Front Suspension arm corroded and seriously weakened |2.4.G.1| | 4 |
| Centre Rear fog lamp not working |1.3.2b| | 4 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 4 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 4 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 4 |
| Offside Front brake disc has restricted free movement |3.5.1j| | 4 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 4 |
| Offside Inner Front brake disc excessively scored |3.5.1h| | 4 |
| Offside Front Position lamp not working side light (4.2.1 (a) (ii)) | 4 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 4 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis |2.4.A.3| | 4 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 4 |
| Offside Front Valve stem seriously damaged |5.2.3 |j|| | 4 |
| Offside Front Drivers seat fore and aft adjustment mechanism not functioning as intended. (6.2.5 (b) (i)) | 4 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 4 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 4 |
| Offside Rear front parking brake recording little or no effort |3.7.B.6a| | 4 |
| Nearside Front Headlamp aim not tested (4.1.2 (b)) | 4 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 4 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 4 |
| Offside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Nearside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
| Offside Front Anti-roll bar fractured |2.4.G.1| | 4 |
| Nearside Rear Parking |secondary brake| on a single line braking system has no recorded effort at a wheel |1.3.1 |a| |ii|| | 4 |
| Offside Front Steering locking device missing |2.2.C.1g| | 4 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner and outer sill |5.2.6| | 4 |
| Exhaust carbon monoxide content at idle exceeds manufacturer`s specified limits |8.2.1.2 |b|| | 4 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch |7.1.1 |a| |i|| | 4 |
| Nearside Headlamp levelling device inoperative (4.1.5 (a)) | 4 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis |6.1.1 |c| |i|| | 4 |
| Nearside Front Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 4 |
| Nearside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis |5.3.6 |a| |ii|| | 3 |
| Parking brake inoperative on one side both sides (1.4.1 (a)) | 3 |
| Offside Front Brake hose connection leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 3 |
| Nearside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Rear Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 3 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 3 |
| Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 3 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch |7.1.1 |a| |i|| | 3 |
| Offside Front Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 3 |
| Nearside Rear Floor excessively deteriorated (6.2.4 (a) (i)) | 3 |
| Nearside Rear Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 3 |
| Offside Front Subframe mounting prescribed area is excessively corroded floor |2.4.A.3| | 3 |
| Nearside Rear Anti-roll bar insecure |2.4.G.1| | 3 |
| Offside Inner Rear brake disc excessively pitted |3.5.1h| | 3 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 3 |
| Nearside Front Lower Suspension arm locating pin locking device missing |2.4.G.3b| | 3 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 3 |
| Offside Floor excessively deteriorated (6.2.4 (a) (i)) | 3 |
| Nearside Rear Sub-frame attachment bracket/mounting likely to fail (5.3.3 (b) (ii)) | 3 |
| Offside Rear Sub-frame attachment bracket/mounting likely to fail (5.3.3 (b) (ii)) | 3 |
| Nearside Windscreen wiper blade missing |8.2.2| | 3 |
| Power steering pipe|s| or hose|s| leaking from a seal |2.3.3b| | 3 |
| Power steering inoperative |2.1.5 |c| |i|| | 3 |
| Offside Front Tie bar/rod insecure |2.4.G.1| | 3 |
| Offside Outer Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under sill (7.1.1 (a) (i)) | 3 |
| Front Brake pipe leaking |3.6.A.1| | 3 |
| Nearside Front Upper Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Rear Suspension arm corroded and seriously weakened both |2.4.G.1| | 3 |
| Offside Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 3 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 3 |
| Offside Rear Radius arm corroded and seriously weakened |2.4.G.1| | 3 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 3 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 3 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 3 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 3 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Offside Rear Brake hose leaking |3.6.A.1| | 3 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 3 |
| Offside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 3 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill area |2.4.A.3| | 3 |
| Horn control missing |1.6.1| | 3 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 3 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 3 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area (7.1.1 (a) (i)) | 3 |
| Offside Rear Parking |secondary brake| on a single line braking system has no recorded effort at a wheel |1.3.1 |a| |ii|| | 3 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 3 |
| Offside Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 3 |
| Offside Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 3 |
| Nearside Front Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 3 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 3 |
| Offside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 3 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Rear Anti-roll bar ball joint excessively worn |5.3.4 |a| |i|| | 3 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 3 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 3 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 3 |
| Offside Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 3 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 3 |
| Offside Front Anti-roll bar damaged and seriously weakened |2.4.G.1| | 3 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 3 |
| Nearside Front Sub-frame corroded and seriously weakened |2.4.G.1| | 3 |
| Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 3 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 3 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis |5.3.6 |a| |i|| | 3 |
| Central Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 3 |
| Offside Front Brake hose stretched |found during steering lock to lock check| |2.2.D.2b| | 3 |
| Offside Front Upper Suspension arm corroded and seriously weakened |2.4.G.1| | 3 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Nearside Rear Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Rear position lamp|s| incomplete |1.1.4a| | 3 |
| Offside Rear All position lamps not working |1.1.A.3b| | 3 |
| Nearside Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 3 |
| Emissions unable to be completed (8.2.2.2 (e)) | 3 |
| Body has a sharp edge caused by damage |6.1.C.1| | 3 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 3 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Offside Front Front position lamp|s| not working side light |1.1.A.3b| | 3 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg |6.1.1 |c| |i|| | 3 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 3 |
| Nearside Rear Inner Suspension spring mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 3 |
| Offside Rear Inner Suspension spring mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 3 |
| Offside Front Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 3 |
| Offside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 3 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction |3.1 |a| |ii|| | 3 |
| Offside Rear Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 3 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 3 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 3 |
| Offside Seat belt retracting mechanism defective |5.2.5b| | 3 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 3 |
| Offside Rear Electrical wiring insecure |1.9.2a| | 3 |
| Offside Rear brake disc has restricted free movement |3.5.1j| | 3 |
| Nearside Front Road wheel cracked |4.2.A.1a| | 3 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 3 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 3 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 3 |
| Nearside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength boot floor (5.3.6 (a) (i)) | 3 |
| Offside Rear Lower Suspension arm fractured (5.3.3 (b) (ii)) | 3 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL |7.1.1 |a| |i|| | 3 |
| Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 3 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 3 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor (6.1.1 (c) (i)) | 3 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 3 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 3 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired outer sill |2.4.A.3| | 3 |
| Driver`s airbag missing |7.1.5 |a|| | 3 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 3 |
| Rear Braking system leaking |3.6.A.1| | 3 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 3 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 3 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 3 |
| Offside Rear Inner brake disc in such a condition that it is seriously weakened |3.5.1i| | 3 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 3 |
| Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Nearside Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 3 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed and corroded (7.1.1 (a) (i)) | 3 |
| Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 3 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 3 |
| Rear Exhaust has a major leak of exhaust gases joint (6.1.2 (a)) | 3 |
| Offside Front Steering rack gaiter insecure |2.2.D.2d| | 3 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 3 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 3 |
| Windscreen wiper not working (3.4 (a)) | 3 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 3 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 3 |
| Nearside Front Front position lamp|s| obviously incorrectly positioned |1.1.A.3a| | 3 |
| Offside Rear Inner Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 3 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis Rail (5.3.6 (a) (i)) | 3 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill |6.2.2 |d| |i|| | 3 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Service brake lagging in operation |1.2.1 |d|| | 3 |
| Centre Exhaust system not adequately supported |7.1.1| | 3 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 3 |
| Nearside Rear Body has a projection caused by corrosion |6.1.C.1| | 3 |
| Offside Rear Anti-roll bar linkage fractured |5.3.3 |b| |ii|| | 3 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 3 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 3 |
| Nearside Front Wheel nut|s| loose |4.2.A.1e| | 3 |
| Offside Rear Wheel nut|s| loose |4.2.A.1e| | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 3 |
| Service brake efficiency less than 50% of the required value |1.2.2 |a| |ii|| | 3 |
| Nearside Front Anti-roll bar missing |2.4.G.1| | 3 |
| Nearside Front Anti-roll bar linkage missing |2.4.G.1| | 3 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Offside Rear Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 3 |
| Nearside Rear Brake disc contaminated (1.1.14 (b)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 3 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 3 |
| Offside Front Upper Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Nearside Inner Rear Road wheel bead rim badly distorted |4.2.A.1a| | 3 |
| Headlamp aim unable to be tested (4.1.2 (b)) | 3 |
| Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 3 |
| Nearside Front Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 3 |
| Power steering inoperative and steering adversely affected |2.1.5 |c| |ii|| | 3 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 3 |
| Offside Front Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 3 |
| Nearside Front Upper Suspension arm corroded and seriously weakened |2.4.G.1| | 3 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
| Offside Front Upper Coil spring fractured or broken (5.3.1 (b) (i)) | 3 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 3 |
| Offside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Rear Braking system leaking pipe |3.6.A.1| | 3 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper (1.1.16 (b) (i)) | 3 |
| Nearside Front Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 3 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 3 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 3 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened |5.3.3 |b| |i|| | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill |5.3.6 |a| |i|| | 3 |
| Offside Rear Lower Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 3 |
| Offside Rear Battery insecure |1.9.1| | 3 |
| Nearside Front Position lamp with a multiple light source more than 1/2 not functioning (4.2.1 (a) (ii)) | 3 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill |5.3.6 |a| |i|| | 3 |
| Nearside Rear coil spring broken (2.4.C.1a) | 3 |
| Front Power steering component leaking (2.1.5 (a)) | 3 |
| Nearside Front front brake binding (3.7.B.1) | 3 |
| Nearside Headlamp levelling device inoperative |4.1.5 |a|| | 3 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SILL |7.1.1 |a| |i|| | 3 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 3 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 3 |
| Nearside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 3 |
| Fuel cap/sealing device sealing washer missing |7.2.4c| | 3 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Offside Front Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 3 |
| Offside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis (5.3.3 (b) (i)) | 3 |
| Headlamp light source and lamp not compatible (4.1.4 (c)) | 3 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
| Offside Front Vehicle structure is fractured and structural rigidity is significantly reduced |6.1.1 |a| |i|| | 3 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 3 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 3 |
| Front Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 3 |
| Nearside Rear Braking system leaking Caliper |3.6.A.1| | 3 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 3 |
| Central Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Rear Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 3 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 3 |
| Offside Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 3 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
| Parking brake lever has no reserve travel (3.1.6b) | 3 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 3 |
| Nearside Front Service brake excessively fluctuating |1.2.1 |e|| | 3 |
| Nearside Front position lamp|s| obscured more than 50% |1.1.A.3c| | 3 |
| Nearside Rear brake disc contaminated by brake fluid |3.5.1h| | 3 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Offside Front Upper Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 3 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner arch |5.2.6| | 3 |
| Offside Front Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 3 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 3 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassi (5.3.6 (a) (i)) | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 3 |
| Offside All position lamps not working |1.1.A.3b| | 3 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 3 |
| Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 3 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 3 |
| Nearside Rear Front position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 3 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch |7.1.1 |a| |i|| | 3 |
| Nearside Front Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 3 |
| Offside Rear Brake cable has restricted free movement |3.5.1k| | 3 |
| Drivers view of the road through the swept area of the windscreen materially affected by an obstruction (3.1 (a) (ii)) | 3 |
| Drivers seat fore and aft adjustment mechanism not functioning as intended. (6.2.5 (b) (i)) | 3 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch |7.1.1 |a| |i|| | 3 |
| Nearside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill |6.2.2 |d| |i|| | 3 |
| Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Offside Front brake disc contaminated by brake fluid |3.5.1h| | 3 |
| Front Service brake imbalanced across an axle |1.2.1 |b| |i|| | 3 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 3 |
| Offside Rear Rear position lamp|s| incorrect colour |1.1.A.3e| | 3 |
| Offside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 3 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 3 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 3 |
| Front Headlamp levelling device inoperative (4.1.5 (a)) | 3 |
| Nearside front parking brake recording little or no effort |3.7.B.6a| | 3 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill (7.1.1 (a) (i)) | 3 |
| Exhaust engine idle speed too high |7.3.D.1| | 3 |
| Nearside Front Headlamp aim unable to be tested (4.1.2 (b)) | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area (5.3.6 (a) (i)) | 3 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mount |2.4.A.3| | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar (5.3.6 (a) (i)) | 3 |
| Offside Rear Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 3 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 3 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 3 |
| Offside Rear Service brake indicates brake bind |3.7.D.2a| | 3 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 3 |
| Anti-lock braking system warning lamp does not illuminate |1.6 |a|| | 3 |
| Headlamp not working on dipped beam |1.7.5a| | 3 |
| Rear rear brake recording little or no effort |3.7.B.5a| | 3 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill |6.1.B.2| | 3 |
| Offside Obligatory mirror insecure |8.1.1| | 3 |
| Hazard warning switch insecure |1.4.B.1d| | 3 |
| Offside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 3 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 3 |
| Nearside Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 3 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 3 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 3 |
| Offside Rear Brake hose excessively damaged |3.6.B.4d| | 3 |
| Nearside Rear Brake hose leaking |3.6.A.1| | 3 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 3 |
| Front front brake recording little or no effort |3.7.B.5a| | 3 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 3 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Lower Ball joint has excessive play |2.2.B.1f| | 3 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 3 |
| Nearside Rear Brake hose twisted |3.6.B.4c| | 3 |
| Nearside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 3 |
| Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 3 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 3 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 3 |
| Rear Rear fog lamp not working (1.3.2b) | 3 |
| Nearside Front Upper Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Emissions unable to be completed exhaust leak (8.2.1.2 (d)) | 3 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner arch (6.1.1 (c) (i)) | 3 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner arch (6.1.1 (c) (i)) | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill area |5.2.6| | 3 |
| Nearside Rear Road wheel badly damaged |4.2.A.1a| | 3 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 3 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 3 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 3 |
| Nearside Front Tie bar/rod insecure |2.4.G.1| | 3 |
| Offside Seat belt locking mechanism does not secure or release |5.2.5a| | 3 |
| Exhaust has a major leak of exhaust gases rear box |7.1.2| | 3 |
| Offside Front Body panel insecure wing (6.2.1 (a) (i)) | 3 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 3 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 3 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 3 |
| Offside Stop lamp emits other than a steady red light |1.2.1e| | 3 |
| Rear Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 3 |
| Nearside Front Headlamp levelling device inoperative (4.1.5 (a)) | 3 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SILL (7.1.1 (a) (i)) | 3 |
| Nearside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 3 |
| Rear fog lamp tell-tale missing (4.9.1 (a) (ii)) | 3 |
| Fuel system component leaking |7.2.3| | 3 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3) | 3 |
| Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 3 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 3 |
| Offside Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
| Power steering component leaking rack (2.1.5 (a)) | 3 |
| Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 3 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Rear Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 3 |
| Offside Front Anti-lock braking system component missing |3.4.2| | 3 |
| Nearside Rear Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 3 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Front Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 3 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 3 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill |7.1.1 |a| |i|| | 3 |
| Offside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 3 |
| Nearside Front Brake hose damaged and likely to fail (1.1.12 (a)) | 3 |
| Nearside Rear Braking system leaking calliper |3.6.A.1| | 3 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 3 |
| Nearside Front front brake grabbing severely |3.7.A.2b| | 3 |
| Electronic stability control warning lamp indicates a fault (7.12 (e)) | 3 |
| Exhaust has a major leak of exhaust gases back box |7.1.2| | 3 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 3 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 3 |
| Nearside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 3 |
| Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Nearside Outer Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Nearside Front Brake hose leaking |3.6.A.1| | 3 |
| Nearside Front Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 3 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded Outer sill |2.4.A.3| | 3 |
| Offside front brakes release unevenly |3.7.B.4| | 3 |
| Offside Rear Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Headlamp lens seriously defective both (4.1.1 (b) (ii)) | 3 |
| Offside Front Road wheel bead rim badly distorted |4.2.A.1a| | 3 |
| Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 3 |
| Nearside Front Shock absorber insecure |2.7.2b| | 3 |
| Front An item not tested |Manual| | 3 |
| Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Nearside Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 3 |
| Offside Obligatory mirror insecure (3.3 (b) (ii)) | 3 |
| Nearside Rear Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Rear front brake binding |3.7.B.1| | 3 |
| Speedometer cannot be illuminated (7.8 (c) (ii)) | 3 |
| Rear coil spring broken both |2.4.C.1a| | 3 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Nearside Front brake caliper securing device loose |3.5.1j| | 3 |
| All position lamps not working |1.1.A.3b| | 3 |
| Brake fluid not visible (1.1.10 (d) (iii)) | 3 |
| Front Position lamp not working both sides (4.2.1 (a) (ii)) | 3 |
| Offside Front Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 3 |
| Offside Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 3 |
| Centre Rear Upper Stop lamp not working |1.2.1b| | 3 |
| Offside Headlamp aim unable to be tested (4.1.2 (b)) | 3 |
| Centre Braking system leaking |3.6.A.1| | 3 |
| Front Position lamp not working |4.2.1 |a|| | 3 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 3 |
| Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 3 |
| Hydraulic fluid leaking excessively (8.4.1 (a) (i)) | 3 |
| Hazard warning switch faulty |1.4.B.1d| | 3 |
| Parking brake lever has excessive movement indicating incorrect adjustment no reserve travel (1.1.6 (c)) | 3 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 3 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 3 |
| Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 3 |
| Offside Front coil spring broken (2.4.C.1a) | 3 |
| Nearside Rear Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 3 |
| Offside Rear Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 3 |
| Nearside Front Upper Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 3 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 3 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Outer sill |2.4.A.3| | 3 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper |3.6.A.1| | 3 |
| Nearside Rear An item not tested |Manual| | 3 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 3 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 3 |
| Offside Front Suspension arm insecurely attached (5.3.3 (a) (i)) | 3 |
| Offside Rear Anti-roll bar linkage attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 3 |
| Nearside Rear Road wheel distorted |4.2.A.1a| | 3 |
| Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 3 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 3 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Rear fog lamp tell tale not working |1.3.1b| | 2 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 2 |
| Rear parking brake recording little or no effort | 2 |
| Nearside Front coil spring incomplete |2.4.C.1a| | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Emissions not tested (8.2.1.2 (d)) | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Drivers door cannot be opened from outside the vehicle (6.2.3 (a)) | 2 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 2 |
| Offside Rear Shock absorbers has a serious fluid leak | 2 |
| Nearside Rear Shock absorbers has a serious fluid leak | 2 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 2 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill (6.2.2 (d) (i)) | 2 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Rear fog lamp obviously incorrectly positioned (4.5.4 (a)) | 2 |
| Nearside Front Upper Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Offside Front Upper Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Nearside Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened (5.3.1 (b) (i)) | 2 |
| Nearside Front Subframe mounting prescribed area is excessively corroded floor to sill |2.4.A.3| | 2 |
| Offside Front Body component insecure wing (6.2.1 (a) (i)) | 2 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded outer sill holed |2.4.A.3| | 2 |
| Central Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 2 |
| Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt both (5.3.4 (b) (ii)) | 2 |
| Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill area |2.4.A.3| | 2 |
| Nearside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Front Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 2 |
| Offside Front position lamp|s| obscured more than 50% |1.1.A.3c| | 2 |
| Nearside Front Track rod end damaged and unserviceable |2.2.C.1d| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis inner wing (5.3.6 (a) (i)) | 2 |
| Steering system excessively rough |2.2.D.1| | 2 |
| Nearside Front Hydraulic brake calliper leaking |1.1.16 |b| |i|| | 2 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 2 |
| Emissions not tested due to exhaust blow |8.2.1.2 |d|| | 2 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area (7.1.1 (a) (i)) | 2 |
| Offside Front Seat belt not functioning as intended (7.1.2 (c)) | 2 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 2 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Front Position lamp not working Both (4.2.1 (a) (ii)) | 2 |
| Offside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 2 |
| Offside Rear Wheel bearing rough when rotated |5.1.3 |b| |i|| | 2 |
| Offside Front Anti-roll bar linkage missing (5.3.3 (a) (ii)) | 2 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Position lamp not working Sidelight (4.2.1 (a) (ii)) | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner and outer sill |5.2.6| | 2 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Emissions not tested due to coolant leak (8.2.1.2 (d)) | 2 |
| Offside Rear Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch |6.1.B.2| | 2 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch |6.1.B.2| | 2 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch |6.1.B.2| | 2 |
| Nearside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Offside Rear Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure (5.3.3 (a) (i)) | 2 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 2 |
| Brake fluid contaminated Tested during prechecks |1.8 |a|| | 2 |
| Front Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 2 |
| Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
| Nearside Headlamp light source and lamp not compatible |4.1.4 |c|| | 2 |
| Offside Headlamp light source and lamp not compatible |4.1.4 |c|| | 2 |
| Offside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
| Rear fog lamp does not emit a steady red light |1.3.2e| | 2 |
| Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 2 |
| Brake pipe leaking on an air braking system (1.1.11 (b) (i)) | 2 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel arch (7.1.1 (a) (i)) | 2 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 2 |
| Seat belt anchorage prescribed area is excessively corroded nearside rear outer sill |5.2.6| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis under wheel arch |5.3.6 |a| |i|| | 2 |
| Nearside Front Outer Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis |5.3.6 |a| |i|| | 2 |
| Nearside Front Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill |7.1.1 |a| |i|| | 2 |
| Nearside Rear Brake hose inappropriately repaired |3.6.A.3| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 2 |
| Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Anti-roll bar linkage rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Rear Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 2 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper (1.1.16 (b) (i)) | 2 |
| Nearside Outer Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 2 |
| Offside Rear Suspension arm corroded and seriously weakened lower arm |5.3.3 |b| |i|| | 2 |
| Nearside Rear Suspension arm corroded and seriously weakened lower arm |5.3.3 |b| |i|| | 2 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 2 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 2 |
| Nearside Seat belt retracting mechanism defective |5.2.5b| | 2 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Parking (secondary brake) on a single line braking system imbalanced across an axle Axle 1 (1.3.1 (b) (i)) | 2 |
| Offside Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 2 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 2 |
| Brake fluid contaminated (1.8 (a)) | 2 |
| Nearside Front Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill panel (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength main chassis (5.3.6 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength main chassis (5.3.6 (a) (i)) | 2 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced door sill (7.1.1 (a) (i)) | 2 |
| Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Offside Front Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Rear fog lamp tell tale missing |1.3.1b| | 2 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 2 |
| Offside Rear Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 2 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 2 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch |6.2.2 |d| |i|| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner/outer sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sil (7.1.1 (a) (i)) | 2 |
| Nearside Inner Rear brake disc excessively scored |3.5.1h| | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 2 |
| Offside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 2 |
| Nearside Front Anti-roll bar linkage likely to become detached (5.3.3 (a) (ii)) | 2 |
| Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 2 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 2 |
| Nearside Rear Electrical wiring insecure |1.9.2a| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer seal |5.2.6| | 2 |
| Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Front Side repeater missing (4.4.1 (a) (ii)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis inner wing (5.3.6 (a) (i)) | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 2 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL |6.1.B.2| | 2 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing |5.3.6 |a| |i|| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis rail |2.4.A.3| | 2 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 2 |
| Emissions unable to be completed Engine misfire (8.2.1.2 (d)) | 2 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill |5.2.6| | 2 |
| Nearside Rear brake disc has restricted free movement |3.5.1j| | 2 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 2 |
| Nearside Rear Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.A.1| | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor (6.1.1 (c) (i)) | 2 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor |6.1.1 |c| |i|| | 2 |
| Fuel cap/sealing device missing |6.1.3 |b| |i|| | 2 |
| Front Service brake application uneven across the axle |3.7.D.2b| | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill (7.1.1 (a) (i)) | 2 |
| Nearside Rear Brake pipe at imminent risk of failure or fracture (1.1.11 (a)) | 2 |
| Offside Rear Brake pipe inadequately clipped |3.6.B.1| | 2 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 2 |
| Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 2 |
| Exhaust catalytic converter missing where one was fitted as standard |8.2.2.1 |a|| | 2 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 2 |
| Headlamp aim not tested |4.1.2 |b|| | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 2 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Rear Inner brake disc in such a condition that it is seriously weakened |3.5.1i| | 2 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced battery tray (6.1.1 (c) (i)) | 2 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 2 |
| Offside Front Brake hose excessively twisted (1.1.12 (b) (ii)) | 2 |
| Nearside Power steering pipe/hose leaking (2.1.5 (a)) | 2 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 2 |
| Nearside Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 2 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 2 |
| Offside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Emissions not tested exhaust leak (8.2.1.2 (d)) | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 2 |
| Front Power steering component|s| leaking |2.3.3b| | 2 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front chassis legs (5.3.6 (a) (i)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill area |7.1.1 |a| |i|| | 2 |
| Central Exhaust has a major leak of exhaust gases section (6.1.2 (a)) | 2 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 2 |
| Offside Steering rack insecure |2.2.B.1a| | 2 |
| Nearside Rear Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Rear Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both floors (7.1.1 (a) (i)) | 2 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both outer sills (7.1.1 (a) (i)) | 2 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch |6.1.1 |c| |i|| | 2 |
| Nearside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar |2.4.A.3| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar |2.4.A.3| | 2 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Front Upper Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Centre Brake pipe leaking |3.6.A.1| | 2 |
| Nearside Rear Inner Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 2 |
| Front Power steering pipe/hose excessively corroded (2.1.5 (g) (i)) | 2 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Nearside Front Subframe mounting prescribed area is excessively corroded Chassis |2.4.A.3| | 2 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Seat belt webbing significantly weakened (7.1.2 (b) (ii)) | 2 |
| Offside Front Lower Anti-roll bar linkage insecure |2.4.G.1| | 2 |
| Offside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Rear Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 2 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bearing |2.4.G.2| | 2 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Front Wheel nut|s| loose |4.2.A.1e| | 2 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 2 |
| Nearside Rear Lower Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 2 |
| Offside Rear Upper Suspension arm fractured (5.3.3 (b) (ii)) | 2 |
| Nearside Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush broken |2.4.G.2| | 2 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 2 |
| Offside Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 2 |
| Nearside Side repeater missing |4.4.1 |a| |ii|| | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 2 |
| Emissions not tested |8.2.2.2 |e|| | 2 |
| Central Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 2 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 2 |
| Nearside Seat belt webbing significantly weakened (7.1.2 (b) (ii)) | 2 |
| Nearside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting sill (6.2.2 (d) (i)) | 2 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 2 |
| Offside Rear Brake pipe at imminent risk of failure or fracture |1.1.11 |a|| | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 2 |
| Brake pedal creeps down under servo assistance and touches the floor |3.3.C.3| | 2 |
| Front Service brake excessively binding both (1.2.1 (f)) | 2 |
| Offside Rear Body panel corroded and likely to cause injury Wheel arch (6.2.1 (a) (i)) | 2 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| front brake binding both |3.7.B.1| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 2 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front Brake pipe at imminent risk of failure or fracture to rear (1.1.11 (a)) | 2 |
| Offside Front Lower Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Exhaust has a major leak of exhaust gases rear silencer |7.1.2| | 2 |
| Power steering fluid reservoir empty |2.1.5 |b| |ii|| | 2 |
| Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 2 |
| Nearside Front Anti-roll bar linkage pin or bush likely to become detached |5.3.4 |a| |ii|| | 2 |
| Centre Front Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 2 |
| Nearside Rear Anti-roll bar locating pin insecure |2.4.G.3a| | 2 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 2 |
| Offside Front Seat belt affected by an insecure seat fixing |5.2.1b| | 2 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Front Position lamp not working both |4.2.1 |a| |ii|| | 2 |
| Nearside Front Upper Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Brake cable has restricted free movement |3.5.1k| | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 2 |
| Offside Front Outline marker lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis leg |2.4.A.3| | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch |7.1.1 |a| |i|| | 2 |
| Rear Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 2 |
| Nearside Rear Upper Coil spring fractured or broken |5.3.1 |b| |i|| | 2 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 2 |
| Exhaust catalytic converter obviously defective (8.2.1.1 (a)) | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 2 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 2 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg |6.1.A.1| | 2 |
| Nearside Front Vehicle structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 2 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened |5.3.3 |b| |i|| | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill |5.3.6 |a| |i|| | 2 |
| Brake pipe leaking on a hydraulic braking system Front to rear (1.1.11 (b) (ii)) | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis inner arch |2.4.A.3| | 2 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |6.1.A.1| | 2 |
| Rear Service brake imbalanced across an axle (1.2.1 (b) (i)) | 2 |
| Offside Front Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis leg |2.4.A.3| | 2 |
| Centre Front Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 2 |
| Offside Headlamps matched pair are incorrectly positioned |1.7.3| | 2 |
| Stop lamp(s) not working high level (4.3.1 (a) (ii)) | 2 |
| Offside Rear Brake cable has restricted free movement (1.1.15 (e)) | 2 |
| Front Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 2 |
| Front Position lamp not working both side |4.2.1 |a|| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear brake caliper securing device loose |3.5.1j| | 2 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Front Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Front Headlamp not working on dipped beam (1.7.5a) | 2 |
| Nearside Headlamp not working on dipped beam (1.7.5a) | 2 |
| Nearside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 2 |
| Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 2 |
| Nearside Front Road wheel badly distorted (5.2.2 (c) (i)) | 2 |
| Rear Service brake excessively fluctuating both |1.2.1 |e|| | 2 |
| Nearside Front Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 2 |
| Offside Rear Anti-roll bar ball joint dust cover missing |2.4.G.2| | 2 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded Outer sill. |5.2.6| | 2 |
| Exhaust has a major leak of exhaust gases rear silencer (6.1.2 (a)) | 2 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wing/chassis |2.4.A.3| | 2 |
| Nearside front brakes release unevenly |3.7.B.4| | 2 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 2 |
| Nearside Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 2 |
| Nearside Rear Coil spring fractured or broken Broken (5.3.1 (b) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired inner sill (5.3.6 (a) (i)) | 2 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 2 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 2 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis (5.3.3 (b) (i)) | 2 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 2 |
| Nearside Side repeater missing (4.4.1 (a) (ii)) | 2 |
| Indicator tell tale inoperative |1.4.A.2a| | 2 |
| Nearside rear brake grabbing severely |3.7.A.5b| | 2 |
| Nearside Front Anti-roll bar linkage fractured Broken |2.4.G.1| | 2 |
| Rear Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 2 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer sill (6.2.2 (d) (i)) | 2 |
| Nearside Rear Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 2 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached detached (5.3.4 (a) (ii)) | 2 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 2 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Offside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Front Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 2 |
| Front Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Rear Exhaust has a major leak of exhaust gases joint |6.1.2 |a|| | 2 |
| Front Lower Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 2 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Position lamp not working both fronts (4.2.1 (a) (ii)) | 2 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 2 |
| Nearside Front Subframe mounting prescribed area is fractured |2.4.A.3| | 2 |
| Offside Rear Stop lamp|s| lens defective such that the emitted light is adversely affected |4.3.1 |b| |ii|| | 2 |
| Offside Headlamp not in good working order |not working| |1.2.4a| | 2 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 2 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 2 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 2 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Power steering pump leaking (2.1.5 (a)) | 2 |
| Seat belt anchorage prescribed area is excessively corroded rear of off side sill panel area |5.2.6| | 2 |
| Nearside Inner Front Brake lining|s| less than 1.5 mm thick |3.5.1g| | 2 |
| Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Outer Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Offside Outer Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Nearside Front Brake pipe twisted |found during steering lock to lock check| |2.2.D.2b| | 2 |
| Offside Front Anti-roll bar insecurely attached (5.3.3 (a) (i)) | 2 |
| Brake pedal anti-slip provision missing |1.1.2 |c|| | 2 |
| Front Position lamp not working x2 (4.2.1 (a) (ii)) | 2 |
| Nearside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 2 |
| Nearside Rear Brake lever has restricted free movement |3.5.1k| | 2 |
| Nearside Front Valve stem seriously damaged |5.2.3 |j|| | 2 |
| Side repeater incorrect colour both |4.4.3 |a|| | 2 |
| Anti-roll bar linkage has excessive play in a ball joint both front |2.4.G.2| | 2 |
| Offside Front Upper Anti-roll bar linkage insecure |2.4.G.1| | 2 |
| Offside Front Upper Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 2 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 2 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch |7.1.1 |a| |i|| | 2 |
| Drivers door cannot be opened from inside the vehicle (6.2.3 (a)) | 2 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 2 |
| Emissions not tested (8.2.2.2 (e)) | 2 |
| Front position lamp|s| not working both front |1.1.A.3b| | 2 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill. |5.2.6| | 2 |
| Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 2 |
| Offside Rear Stop lamp emits other than a steady red light |1.2.1e| | 2 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 2 |
| Nearside Front Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 2 |
| Exhaust has a major leak of exhaust gases emissions not tested |7.1.2| | 2 |
| Offside brake disc excessively pitted |3.5.1h| | 2 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch |7.1.1 |a| |i|| | 2 |
| Offside Front Electrical wiring insecure abs wire |1.9.2a| | 2 |
| Offside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 2 |
| Nearside Rear Braking system leaking brake calliper |3.6.A.1| | 2 |
| Offside Obligatory mirror seriously obscured affecting the rear view |8.1.2a| | 2 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing (6.1.1 (c) (i)) | 2 |
| Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 2 |
| Offside Rear Direction indicators not working |1.4.A.2c| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch |6.1.B.2| | 2 |
| Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 2 |
| Headlamps matched pair are not the same colour |1.7.6| | 2 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 2 |
| Offside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Offside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Windscreen wiper not operating automatically when switched on |8.2.1b| | 2 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 2 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 2 |
| Nearside Front Lower Power steering pipe|s| or hose|s| leaking |2.3.3b| | 2 |
| Nearside Rear Tie bar/rod worn and seriously weakened |2.4.G.1| | 2 |
| Offside Rear Anti-roll bar linkage insecure and impairing directional stability |5.3.3 |a| |ii|| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired inner sill (7.1.1 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Parking |secondary brake| on a single line braking system grabbing severely |1.3.1 |c|| | 2 |
| Nearside Front Front position lamp|s| not working sidelight |1.1.A.3b| | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded |7.1.1 |a| |i|| | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded |7.1.1 |a| |i|| | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 2 |
| Front front brake binding both |3.7.B.1| | 2 |
| Offside Front Body insecure and dangerous to other road users wing |6.1.B.1b| | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 2 |
| Offside Front Ball joint has excessive play |2.2.B.1f| | 2 |
| Nearside Front Body panel corroded and likely to cause injury lower wing (6.2.1 (a) (i)) | 2 |
| Nearside Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
| Front Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 2 |
| Offside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 2 |
| Nearside Front Position lamp not working sidelight (4.2.1 (a) (ii)) | 2 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
| Offside Rear Anti-roll bar fractured (5.3.3 (b) (ii)) | 2 |
| Front Exhaust system not adequately supported |7.1.1| | 2 |
| Rear Coil spring fractured or broken both (5.3.1 (b) (i)) | 2 |
| Nearside front brake recording little or no effort |3.7.B.5a| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded SILL |5.2.6| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar |5.3.6 |a| |i|| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 2 |
| Nearside Front Outer Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Rear Exhaust has a major leak of exhaust gases pipe (6.1.2 (a)) | 2 |
| Front position lamp|s| not working n/s |1.1.A.3b| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Inner sill |2.4.A.3| | 2 |
| Brake performance not tested pipe burst (1.2.1 (g)) | 2 |
| Nearside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 2 |
| Nearside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 2 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Nearside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Rear Exhaust has a major leak of exhaust gases flange (6.1.2 (a)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg |5.3.6 |a| |i|| | 2 |
| Nearside Rear Body component corroded and likely to cause injury Wheel arch (6.2.1 (a) (i)) | 2 |
| Nearside Front Headlamp not in a clean condition affecting beam image |1.2.4a| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer rear sill |5.2.6| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer rear sill |5.2.6| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner sill |2.4.A.3| | 2 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired chassis leg (5.3.6 (a) (i)) | 2 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 2 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 2 |
| Centre Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
| Nearside Inner Front Road wheel bead rim badly distorted |4.2.A.1a| | 2 |
| Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer sill |5.2.6| | 2 |
| Offside Rear Inner Vehicle structure has excessive corrosion which adversely affects braking or steering sill (6.1.1 (c) (ii)) | 2 |
| Front Front position lamp|s| not working both |1.1.A.3b| | 2 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 2 |
| Offside Front Lower Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor corroded (7.1.1 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded (7.1.1 (a) (i)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded (7.1.1 (a) (i)) | 2 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wing |2.4.A.3| | 2 |
| Offside Front Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 2 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |6.1.1 |c| |ii|| | 2 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail |6.1.1 |c| |i|| | 2 |
| Nearside Front Front position lamp|s| flickers when tapped lightly by hand |1.1.4c| | 2 |
| Offside Rear Anti-roll bar linkage ball joint dust cover missing |2.4.G.2| | 2 |
| Offside Rear Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 2 |
| Nearside Rear Tie bar/rod insecure |2.4.G.1| | 2 |
| Offside Rear Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 2 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL (6.1.1 (c) (i)) | 2 |
| Nearside Front Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 2 |
| Offside Front Headlamp aim beam image too far to the left |1.6.B4| | 2 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wing |2.4.A.3| | 2 |
| Offside Rear Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Electronic stability system warning lamp indicates a fault |3.4.1c| | 2 |
| Offside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Brake disc in such a condition that it is seriously weakened all (1.1.14 (a) (ii)) | 2 |
| Offside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 2 |
| Bonnet cannot be secured in the closed position |8.4.1| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 2 |
| Suspension component mounting prescribed area is excessively corroded both outer sills |2.4.A.3| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at anti roll bar mount (5.3.6 (a) (i)) | 2 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid |1.1.16 |b| |i|| | 2 |
| Nearside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill (7.1.1 (a) (i)) | 2 |
| Offside Front Lower Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 2 |
| Nearside Front Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 2 |
| Offside Rear Anti-roll bar fractured |2.4.G.1| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 2 |
| Central Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 2 |
| Nearside Front Anti-roll bar linkage insecure and impairing directional stability |5.3.3 |a| |ii|| | 2 |
| Nearside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear Parking brake inoperative on one side low (1.4.1 (a)) | 2 |
| Nearside Front Upper Steering locking device missing ball joint (2.1.3 (d)) | 2 |
| Offside Front Upper Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 2 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 2 |
| Offside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 2 |
| Axle insecure (5.1.1 (b) (i)) | 2 |
| Nearside Front Shock absorbers insecurely attached (5.3.2 (a) (i)) | 2 |
| Nearside Rear Brake hose connection leaking on a hydraulic braking system |1.1.12 |c| |ii|| | 2 |
| Nearside Front Direction indicators not working |1.4.A.2c| | 2 |
| Offside Rear Hydraulic fluid leaking excessively brake caliper |8.4.1 |a| |i|| | 2 |
| Nearside Front Statutory seat belt missing |5.1.1| | 2 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 2 |
| Offside Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 2 |
| Offside Rear Hydraulic fluid leaking excessively brake caliper (8.4.1 (a) (i)) | 2 |
| Front Passenger`s airbag obviously defective |5.4.1| | 2 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 2 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 2 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 2 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front Coil spring not correctly located |2.4.C.2| | 2 |
| Brake pedal anti-slip provision worn smooth (1.1.2 (c)) | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded OUTER SILL |5.2.6| | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 2 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill. |5.2.6| | 2 |
| Offside Steering locking device missing track rod end |2.2.C.1g| | 2 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 2 |
| Offside Service brake lagging in operation (1.2.1 (d)) | 2 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg |6.2.2 |d| |i|| | 2 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel (7.1.1 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill |5.3.6 |a| |i|| | 2 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii)) | 2 |
| Nearside Front Body insecure wing (6.2.2 (a) (i)) | 2 |
| Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Upper Stop lamp|s| not working |4.3.1 |a| |ii|| | 2 |
| Nearside Rear Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded |7.1.1 |a| |i|| | 2 |
| Offside Front Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 2 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 2 |
| Steering rack insecure |2.2.B.1a| | 2 |
| Offside Front Headlamp aim unable to be tested (4.1.2 (b)) | 2 |
| Nearside Rear Service brake grabbing severely (1.2.1 (c)) | 2 |
| Nearside Front Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 2 |
| Offside Rear reflector not red in colour |1.5.1d| | 2 |
| Nearside Rear Body panel corroded and likely to cause injury wheel arch |6.2.1 |a| |i|| | 2 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded SILL |5.2.6| | 2 |
| Nearside Front Lower Body panel corroded and likely to cause injury wing (6.2.1 (a) (i)) | 2 |
| Offside Rear Stop lamp|s| all not working |4.3.1 |a| |iii|| | 2 |
| Nearside Rear Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 2 |
| Nearside Front Upper Suspension arm locating pin locking device missing |2.4.G.3b| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/chassis (5.3.6 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS (5.3.6 (a) (i)) | 2 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Brake pipe leaking front to rear |3.6.A.1| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS RAIL |5.3.6 |a| |i|| | 2 |
| Rear fog lamp switch missing |1.3.1a| | 2 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill |6.1.1 |c| |i|| | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 2 |
| Brake master cylinder leaking (1.1.10 (b) (ii)) | 2 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 2 |
| Nearside Front Front position lamp(s) not working (1.1.A.3b) | 2 |
| Rear Exhaust has a major leak of exhaust gases (7.1.2) | 2 |
| Nearside Front Brake pipe seriously damaged |found during steering lock to lock check| |2.2.D.2b| | 2 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 2 |
| Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 2 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3) | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL (7.1.1 (a) (i)) | 2 |
| Offside All direction indicators not working (4.4.1 (a) (ii)) | 2 |
| Offside Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 2 |
| Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt both sides (5.3.4 (b) (ii)) | 2 |
| Central Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 2 |
| Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 2 |
| Power steering component leaking Rack (2.1.5 (a)) | 2 |
| Rear fog lamp switch missing (4.5.3 (a)) | 2 |
| Offside Rear Drive shaft securing bolt missing (6.1.7 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wing (5.3.6 (a) (i)) | 2 |
| Electronic braking system warning device indicates a fault (1.7 (b)) | 2 |
| Nearside Rear Coil spring mounting fractured |2.4.C.3b| | 2 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded seal |2.4.A.3| | 2 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded seal |2.4.A.3| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded boot |2.4.A.3| | 2 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch and chassis leg |2.4.A.3| | 2 |
| Offside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 2 |
| Offside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill area (7.1.1 (a) (i)) | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Nearside Outer Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Road wheel badly distorted (5.2.2 (c) (i)) | 2 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Wheel arch (6.2.2 (d) (i)) | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill |5.3.6 |a| |i|| | 2 |
| Nearside Front Headlamp light intensity severely reduced |4.1.4 |a|| | 2 |
| Nearside Headlamp aim beam image too far to the right |1.6.B4| | 2 |
| Nearside Position lamp not working |4.2.1 |a|| | 2 |
| Offside Front Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 2 |
| Offside Seat belt buckle not functioning as intended (7.1.2 (d)) | 2 |
| Offside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength roll bar mount (5.3.6 (a) (i)) | 2 |
| Offside Windscreen wiper not working (3.4 (a)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 2 |
| Offside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 2 |
| Offside Rear Wheel insecure |4.2.A.1c| | 2 |
| Parking brake lever is impeded in its travel |3.1.6c| | 2 |
| Offside Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened |5.3.1 |b| |i|| | 2 |
| Nearside Front Service brake grabbing severely |3.7.C.2| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 2 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |6.1.1 |c| |ii|| | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 2 |
| Rear Exhaust silencer insecure (8.1.1 (b) (i)) | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Nearside Front Upper Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Nearside Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 2 |
| Offside Rear Brake pipe connection leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 2 |
| Rear Exhaust has a major leak of exhaust gases box |7.1.2| | 2 |
| Front Passenger`s seat insecure |6.2.A.1| | 2 |
| Offside Front Upper Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt boot split (2.1.3 (g) (ii)) | 2 |
| Nearside Front Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 2 |
| Rear Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 2 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Offside Front Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL (5.3.6 (a) (i)) | 2 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 2 |
| Nearside Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Exhaust has a major leak of exhaust gases join to rear silencer |7.1.2| | 2 |
| Nearside Steering rack gaiter insecure |2.2.D.2d| | 2 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Offside Rear Lower Suspension arm likely to fail (5.3.3 (b) (ii)) | 2 |
| Offside Front front brakes release unevenly |3.7.B.4| | 2 |
| Nearside Front Lower Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Front Lower Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 2 |
| Offside Upper Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near upper suspension arm (5.3.6 (a) (i)) | 2 |
| Offside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Nearside Front Windscreen wiper blade missing (3.4 (b) (ii)) | 2 |
| Nearside Front Brake pipe excessively damaged (1.1.11 (c)) | 2 |
| Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 2 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch holed (7.1.1 (a) (i)) | 2 |
| Nearside Track rod end ball joint dust cover missing (2.1.3 (g) (ii)) | 2 |
| Nearside Front Steering locking device missing track rod (2.1.3 (d)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 2 |
| Rear fog lamp missing |1.3.2a| | 2 |
| Position lamp not working both front (4.2.1 (a) (ii)) | 2 |
| Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
| Central Stop lamp(s) not working High level (4.3.1 (a) (ii)) | 2 |
| Nearside Front Side repeater not working |4.4.1 |a| |ii|| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor |5.3.6 |a| |i|| | 2 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL (6.1.1 (c) (i)) | 2 |
| Offside Front Seat belt stitching badly frayed |5.2.2b| | 2 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 2 |
| Seat belt anchorage prescribed area is excessively corroded offside rear inner sill |5.2.6| | 2 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 2 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 2 |
| Central Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Headlamp aim unable to be tested (4.1.2 (b)) | 2 |
| Nearside Front Brake hose excessively stretched (1.1.12 (b) (ii)) | 2 |
| Offside Front Brake hose excessively stretched (1.1.12 (b) (ii)) | 2 |
| Nearside Passengers seat insecure (6.2.6 (a) (ii)) | 2 |
| Offside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Exhaust has a major leak of exhaust gases center (6.1.2 (a)) | 2 |
| Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 2 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Rear Exhaust has a major leak of exhaust gases section (6.1.2 (a)) | 2 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 2 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie leg (5.3.6 (a) (i)) | 2 |
| Nearside Seat belt locking mechanism does not secure or release |5.2.5a| | 2 |
| Headlamp switch faulty |1.7.1| | 2 |
| Offside Rear position lamp|s| insecure |1.1.A.3a| | 2 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 2 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Rear Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 2 |
| Undertray insecure (8.1.1 (b) (i)) | 2 |
| Offside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Parking |secondary brake| on a single line braking system imbalanced across an axle Axle 1 |1.3.1 |b| |i|| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch |6.1.B.2| | 2 |
| Rear All position lamps not working |1.1.A.3b| | 2 |
| Hydraulic fluid leaking excessively power steering pipes (8.4.1 (a) (i)) | 2 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 2 |
| Nearside Inner Front brake disc excessively scored |3.5.1h| | 2 |
| Nearside Front Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 2 |
| Offside Front Headlamp not in a clean condition affecting beam image |1.2.4a| | 2 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Offside Front Shock absorber has an excessively worn bush |2.7.4| | 2 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Rear reflector not red in colour |1.5.1d| | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Front Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Lower Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 2 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 2 |
| Nearside Rear Direction indicator incorrect colour |4.4.3 |a|| | 2 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded (5.3.6 (a) (i)) | 2 |
| Nearside Front Inner Road wheel badly distorted (5.2.2 (c) (i)) | 2 |
| Offside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 2 |
| Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded rear sill |5.2.6| | 2 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis (5.3.6 (a) (ii)) | 2 |
| Nearside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 2 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 2 |
| Offside Front Seat belt anchorage prescribed area is fractured |5.2.6| | 2 |
| Offside Direction indicators not working |1.4.A.2c| | 2 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Nearside Rear Tie bar/rod attachment bracket/mounting insecure |2.4.G.1| | 2 |
| Stop lamp not working centre |1.2.1b| | 2 |
| Nearside Front coil spring broken (2.4.C.1a) | 2 |
| Windscreen has a combination of minor damage areas which restrict the drivers view |8.3.1c| | 2 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper |3.6.A.1| | 2 |
| Front Windscreen wiper not working (3.4 (a)) | 2 |
| Offside Front Windscreen wiper blade missing (3.4 (b) (ii)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer Sill (7.1.1 (a) (i)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer Sill (7.1.1 (a) (i)) | 2 |
| Seat belt anchorage prescribed area is excessively corroded both rear outer sills |5.2.6| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded antiroll bar mount |2.4.A.3| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded antiroll bar mount |2.4.A.3| | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch (7.1.1 (a) (i)) | 2 |
| Offside Rear Rear fog lamp missing |1.3.2a| | 2 |
| Offside Rear Body has a projection caused by corrosion |6.1.C.1| | 2 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded floor |2.4.A.3| | 2 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded Floor and sill |5.2.6| | 2 |
| Nearside Rear Valve stem seriously damaged |5.2.3 |j|| | 2 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper wheel arch (5.3.6 (a) (i)) | 2 |
| Nearside Front Macpherson strut insecure |2.4.G.1| | 2 |
| Nearside Parking brake recording little or no effort |3.7.D.3a| | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired chassis leg (6.2.2 (d) (ii)) | 2 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Brake pedal does not operate a brake fitted to each wheel |3.3.A.3| | 2 |
| Offside Rear Brake pedal does not operate a brake fitted to each wheel |3.3.A.3| | 2 |
| Offside Headlamp has a product on the lens which changes emitted colour to other than white or yellow (4.1.4 (b)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar (5.3.6 (a) (i)) | 2 |
| Nearside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Inner Front position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Rear Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 2 |
| Offside Front Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 2 |
| Offside Front Position lamp with a multiple light source more than 1/2 not functioning flickering (4.2.1 (a) (ii)) | 2 |
| Nearside Side repeater not working |4.4.1 |a| |ii|| | 2 |
| Offside Side repeater not working |4.4.1 |a| |ii|| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner wing |2.4.A.3| | 2 |
| Nearside Front Service brake grabbing severely (1.2.1 (c)) | 2 |
| Offside Front Hydraulic brake calliper leaking and braking performance affected (1.1.16 (b) (ii)) | 2 |
| Nearside Side repeater insecure |1.4.A.2b| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 2 |
| Nearside Body has a sharp edge caused by damage mirror |6.1.C.1| | 2 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 2 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg (5.3.6 (a) (ii)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 2 |
| Offside Rear Rear reflector missing (4.8.2 (a) (ii)) | 2 |
| Nearside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan |5.3.6 |a| |i|| | 2 |
| Offside Braking system leaking |3.6.A.1| | 2 |
| Nearside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 2 |
| Offside Front Supplementary Restraint System warning lamp indicates a fault |5.4.2| | 2 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 2 |
| Offside Braking system leaking front to rear |3.6.A.1| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings lower wing |6.1.B.2| | 2 |
| Nearside Rear Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan (7.1.1 (a) (i)) | 2 |
| Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill to floor (5.3.6 (a) (i)) | 2 |
| Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 2 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 2 |
| Offside Rear Road wheel fixing missing |5.2.1 |a| |i|| | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 2 |
| Offside Front Hydraulic brake calliper insecurely mounted (1.1.16 (c) (i)) | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill hold and corroded |5.2.6| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill hold and corroded |5.2.6| | 2 |
| Offside Front Braking system leaking brake pipe |3.6.A.1| | 2 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Offside Rear Braking system leaking caliper leaking |3.6.A.1| | 2 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired inner wheel arch (5.3.6 (a) (i)) | 2 |
| Brake pipe leaking main front to rear |3.6.A.1| | 2 |
| Nearside Front Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 2 |
| Nearside Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill
|5.2.6| | 2 |
| Nearside Front Position lamp not working 501 (4.2.1 (a) (ii)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 2 |
| Offside Front Seat belt webbing significantly weakened (7.1.2 (b) (ii)) | 2 |
| Offside Front Position lamp with a multiple light source more than 1/2 not functioning (4.2.1 (a) (ii)) | 2 |
| Nearside Steering rack insecure |2.2.B.1a| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill |6.1.B.2| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded rear of outer sill |5.2.6| | 2 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 2 |
| Rear coil spring fractured |2.4.C.1a| | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 2 |
| Offside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened |5.3.3 |b| |i|| | 2 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 2 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced chassis leg |2.4.G.1| | 2 |
| Offside Front Braking system leaking caliper |3.6.A.1| | 2 |
| Nearside Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 2 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Nearside Front Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 2 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Emissions not tested due to exhaust leak (8.2.1.2 (d)) | 2 |
| Exhaust has a major leak of exhaust gases rear silencer joint |7.1.2| | 2 |
| Offside Seat belt anchorage prescribed area is fractured |5.2.6| | 2 |
| Nearside Front Upper Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 2 |
| Offside Front Body panel corroded and likely to cause injury wing (6.2.1 (a) (i)) | 2 |
| Offside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Boot floor |6.1.B.2| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Floor |6.1.B.2| | 2 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 2 |
| Offside Front Brake pipe leaking |3.6.A.1| | 2 |
| Offside Rear Anti-lock braking system wheel speed sensor missing (1.6 (c)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 2 |
| Offside Front Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 2 |
| Service brake excessively binding both front (1.2.1 (f)) | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 2 |
| Nearside Floor excessively deteriorated (6.2.4 (a) (i)) | 2 |
| Offside Front Steering arm has relative movement at its fixings |2.2.B.1h| | 2 |
| Offside Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 2 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within 30cm of nsf lower arm (5.3.6 (a) (i)) | 2 |
| Front Power steering pipe/hose excessively corroded |2.1.5 |g| |i|| | 2 |
| Offside Rear Upper Coil spring fractured or broken |5.3.1 |b| |i|| | 2 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 2 |
| Offside Front Anti-roll bar ball joint excessively worn drop link (5.3.4 (a) (i)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner wheel arch |5.2.6| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Inner wheel arch |5.2.6| | 2 |
| Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Position lamp not working side light (4.2.1 (a) (ii)) | 2 |
| Offside Front Service brake grabbing severely |3.7.C.2| | 2 |
| Offside rear brake recording little or no effort parking brake |3.7.B.5a| | 2 |
| Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill area |5.2.6| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill area |5.2.6| | 2 |
| Nearside coil spring broken |2.4.C.1a| | 2 |
| Centre Upper Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
| Central Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill |6.1.1 |c| |i|| | 2 |
| Exhaust catalytic converter missing where one was fitted as standard |8.2.1.1 |a|| | 2 |
| Front Service brake excessively fluctuating |1.2.1 |e|| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 2 |
| Offside Front Upper Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 2 |
| Offside Front Anti-roll bar attachment bracket/mounting fractured |5.3.3 |b| |ii|| | 2 |
| Rear Brake pipe at imminent risk of failure or fracture left to right (1.1.11 (a)) | 2 |
| Nearside Rear Anti-roll bar fractured |2.4.G.1| | 2 |
| Nearside Front Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 2 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner and outer sill |6.2.2 |d| |i|| | 2 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Headlamp insecure |4.1.1 |c|| | 2 |
| Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Offside Rear Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 2 |
| Undertray likely to become detached (6.2.1 (a) (ii)) | 2 |
| Offside Rear Lower Suspension arm likely to fail |5.3.3 |b| |ii|| | 2 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 2 |
| Offside Front Anti-roll bar linkage rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside Front Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 2 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill end (7.1.1 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 2 |
| Offside Front Obligatory mirror missing |8.1.1| | 2 |
| Offside Rear fog lamp emits a light other than red (1.3.2e) | 2 |
| Nearside Front Brake hose connection leaking on a hydraulic braking system |1.1.12 |c| |ii|| | 2 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 2 |
| Nearside Front position lamp|s| flickers when tapped lightly by hand |1.1.4c| | 2 |
| Centre Rear Lower Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Rear Anti-roll bar attachment bracket/mounting missing (5.3.3 (a) (ii)) | 2 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
| Offside Headlamp levelling device inoperative |4.1.5 |a|| | 2 |
| Brake fluid warning lamp inoperative |3.6.G.2| | 2 |
| Fuel pipe insecure |7.2.1| | 2 |
| Nearside Rear rear parking |secondary| brake grabbing severely |3.7.B.6b| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill back |5.2.6| | 2 |
| Offside Rear front brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded sill
|2.4.A.3| | 2 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint drop link |2.4.G.2| | 2 |
| Seat belt anchorage prescribed area is excessively corroded both outer sills |5.2.6| | 2 |
| Rear Anti-roll bar insecure |2.4.G.1| | 2 |
| Nearside Front front brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Parking |secondary brake| on a single line braking system has no recorded effort at a wheel |1.3.1 |a| |ii|| | 2 |
| Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Front Brake pipe leaking on a hydraulic braking system to rear (1.1.11 (b) (ii)) | 2 |
| Offside Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 2 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill at rear jacking point |6.1.B.2| | 2 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill |6.2.2 |d| |i|| | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill area |2.4.A.3| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded under sill |2.4.A.3| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 2 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 2 |
| Nearside Outer Rear Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 2 |
| Offside Rear Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 2 |
| Nearside Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg (5.3.6 (a) (ii)) | 2 |
| Nearside Front Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL |5.3.6 |a| |i|| | 2 |
| coil spring broken |2.4.C.1a| | 2 |
| Nearside Seat belt anchorage prescribed area is fractured |5.2.6| | 2 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired chassis (5.3.6 (a) (i)) | 2 |
| Nearside Front Road wheel fixing missing |5.2.1 |a| |i|| | 2 |
| Nearside Lower Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 2 |
| Nearside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Nearside Rear front brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Rear Suspension arm damaged and seriously weakened |2.4.G.1| | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill |5.3.6 |a| |i|| | 2 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch (6.2.2 (d) (i)) | 2 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 2 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| front parking |secondary| brakes imbalanced |3.7.B.6b| | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg (5.3.6 (a) (i)) | 2 |
| Offside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 2 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded SILL |2.4.A.3| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill (6.1.B.2) | 2 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened (2.4.G.1) | 2 |
| Nearside Rear Upper Suspension arm corroded and seriously weakened (2.4.G.1) | 2 |
| Offside Rear Upper Suspension arm corroded and seriously weakened (2.4.G.1) | 2 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail |6.1.B.2| | 2 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 2 |
| Nearside Rear Road wheel cracked |4.2.A.1a| | 2 |
| Offside Front Horn not working |1.6.2a| | 2 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected offside front (chassis both sides) (5.3.6 (a) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced offside front (both sides sill) (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp not working on main beam Bulb missing |4.1.1 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassi leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassi leg (5.3.6 (a) (i)) | 1 |
| Nearside Front position lamp|s| not working New bulb fitted |1.1.A.3b| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mounting area |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mounting area |2.4.A.3| | 1 |
| Offside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Headlamp extinguishes when tapped lightly by hand |1.2.4c| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Seat belt anchorage prescribed area is excessively corroded OSR inner sill |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases rear joint |7.1.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill (5.3.6 (a) (ii)) | 1 |
| Offside Track rod end loose |2.2.B.1d| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced body sill |7.1.1 |a| |i|| | 1 |
| Central Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Rear Anti-roll bar linkage ball joint likely to become detached already detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked up with yellow wax (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked up with yellow wax (5.3.6 (a) (i)) | 1 |
| Nearside Front Power steering component leaking (2.1.5 (a)) | 1 |
| Exhaust has a major leak of exhaust gases rear silencer joint (6.1.2 (a)) | 1 |
| Position lamp not working Offside front |4.2.1 |a|| | 1 |
| Rear Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion of offside and nearside rear outer sills within 30cms of lower seat belt mountings |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL |7.1.1 |a| |i|| | 1 |
| Nearside brake caliper leaking |3.6.A.1| | 1 |
| Offside Rear Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SIDE SILL (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SIDE SILL (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Integral body structure is fractured and structural rigidity is significantly reduced sill (6.1.1 (a) (i)) | 1 |
| Nearside Front Upper Power steering pipe/hose leaking |2.1.5 |a|| | 1 |
| Front Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn detached (5.3.4 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill has an inapropiate repair |6.1.1 |c| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill has an inapropiate repair |6.1.1 |c| |i|| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill
|6.1.B.2| | 1 |
| Nearside Front Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt Track rod balljoint grease cover split and perished. |2.1.3 |g| |ii|| | 1 |
| Electrical wiring heavily deteriorated earth lead broken near rear diff (4.11 (b) (ii)) | 1 |
| Brake pipe connection leaking on a hydraulic braking system front to rear at rear join (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill holed |5.2.6| | 1 |
| Offside Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Lower sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Lower sill (6.2.2 (d) (i)) | 1 |
| Offside Front Body has a sharp edge caused by corrosion outer sill |6.1.C.1| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion outer sill |6.1.C.1| | 1 |
| Emissions unable to be completed due to equipment error (8.2.1.2 (d)) | 1 |
| Offside Front Anti-roll bar ball joint likely to become detached detached (5.3.4 (a) (ii)) | 1 |
| Offside Rear Anti-roll bar ball joint likely to become detached detached (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill and inner arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor sub-frame mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor sub-frame mount (5.3.6 (a) (i)) | 1 |
| Offside Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Centre Rear All position lamps not working |1.1.A.3b| | 1 |
| Offside Front Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Exhaust has a major leak of exhaust gases centre to front pipe clamp |6.1.2 |a|| | 1 |
| Central Exhaust has a major leak of exhaust gases pipe joint |6.1.2 |a|| | 1 |
| Offside Front Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Nearside Front Power steering pipe/hose leaking as marked at a joint note pipe is very corroded |2.1.5 |a|| | 1 |
| Emissions not tested unable to lower the co or lambda they are both excessively high |8.2.1.2 |d|| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill excessively corroded. (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired sill back not fully welded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corrosion (7.1.1 (a) (i)) | 1 |
| Offside Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Nearside Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Front Position lamp not working 501 fitted (4.2.1 (a) (ii)) | 1 |
| Nearside Front Position lamp not working 501 fitted (4.2.1 (a) (ii)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill corroded as marked (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill corroded as marked (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering As marked by drivers floor (6.1.1 (c) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner panel / arch |2.4.A.3| | 1 |
| Offside Headlamp not working on dipped beam Aim not tested |1.7.5a| | 1 |
| Nearside Front Seat belt buckle not functioning as intended Not releasing when under tension (7.1.2 (d)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outter sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting underbody near towing eye (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Vehicle structure inadequately repaired such that structural rigidity is significantly reduced sill (6.1.1 (d) (i)) | 1 |
| Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength In sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength In sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Steering rack damaged and unserviceable [steering rack tie rod damaged] |2.2.C.1d| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg & inner arch area |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Offside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Nearside Front Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Rear Exhaust has a major leak of exhaust gases exhaust back box (6.1.2 (a)) | 1 |
| Body has a projection caused by damage |6.1.C.1| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Track rod end ball joint has excessive play lock nut loose |2.1.3 |b| |i|| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
| Offside Rear Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Rear of outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Rear of outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis |5.3.6 |a| |ii|| | 1 |
| Nearside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis |5.3.6 |a| |ii|| | 1 |
| Offside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis |5.3.6 |a| |ii|| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill corroded (7.1.1 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak Centre To Rear box & rear box (8.2.1.1 (b)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced holed at bottom of inner wheel arch where it joins sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Rear Stop lamp(s) not working central (4.3.1 (a) (ii)) | 1 |
| Front Suspension spring mounting prescribed area is inadequately repaired both outer wings corroded + holed + sharp edges (5.3.6 (a) (i)) | 1 |
| Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened both springs excessive corrosion (5.3.1 (b) (i)) | 1 |
| Rear Prop shaft likely to become detached diff bushes worn excessively (6.1.7 (a) (ii)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment No reserve travel. (1.1.6 (c)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis near upper wishbone. |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis near upper wishbone. |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer body sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch / chassis near anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced inner/outer sills (7.1.1 (a) (i)) | 1 |
| Offside Rear Braking system leaking Offside rear brake caliper leaking (1.1.3 (d)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill @ several places (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch @ several places (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper & lower arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Brake lever has restricted free movement caliper (1.1.15 (e)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner arch holed within 30cm of anti roll bar fixing (5.3.6 (a) (i)) | 1 |
| Nearside Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Steering column top bearing excessively worn |2.1.2c| | 1 |
| Nearside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Rear Brake pipe at imminent risk of failure or fracture front to rear section across axle (1.1.11 (a)) | 1 |
| Offside Rear Brake pipe at imminent risk of failure or fracture front to rear section at t piece (1.1.11 (a)) | 1 |
| Rear Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 1 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Nearside Front Anti-roll bar linkage rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Upper Suspension arm attachment bracket/mounting insecure (5.3.3 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Brake hose leaking on a hydraulic braking system hose into caliper (1.1.12 (c) (ii)) | 1 |
| Parking brake lever defective so that it cannot be satisfactorily operated (1.1.6 (d)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill corroded and holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill corroded and holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced battery box corroded and holed (6.1.1 (d) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Rear Parking brake inoperative on one side both side (1.4.1 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chalked |5.3.6 |a| |i|| | 1 |
| Offside Rear Lower Suspension component attachment bracket/mounting corroded and seriously weakened shock mount into lower arm |5.3.3 |b| |i|| | 1 |
| Offside Front Lower Front suspension has excessive movement at a suspension ball joint |2.5.A.1c| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Rear sill corroded through |6.2.2 |d| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Rear sill corroded through |6.2.2 |d| |i|| | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg between front bumper and front wheel marked yellow |6.1.1 |c| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer marked yellow |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner marked yellow |7.1.1 |a| |i|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired chassis leg (6.2.2 (d) (ii)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired floor (6.2.2 (d) (ii)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced by the rear frame (6.1.1 (c) (i)) | 1 |
| Front Horn not working (7.7 (a)) | 1 |
| Nearside Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill floor x2 marked (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill
|2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases back box has section missing |7.1.2| | 1 |
| Offside Front Fuel pipe leaking |7.2.3| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill area (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Floor area (7.1.1 (a) (i)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill and sill box end corroded and holed. (7.1.1 (a) (i)) | 1 |
| Suspension arm corroded and seriously weakened both rear |5.3.3 |b| |i|| | 1 |
| Nearside Front Anti-roll bar linkage missing |5.3.3 |a| |ii|| | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting centre outer sill (6.2.2 (d) (i)) | 1 |
| Front Service brake excessively binding both sides (1.2.1 (f)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rear inner sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill wheel arch (6.2.2 (d) (i)) | 1 |
| Emissions not tested lambda reading too high to start test (8.2.1.2 (d)) | 1 |
| Offside Rear rear brake recording little or no effort (3.7.B.5a) | 1 |
| Nearside Front Direction indicator lens defective such that the emitted light is adversely affected - Tinted (4.4.1 (b) (ii)) | 1 |
| Offside Front Direction indicator lens defective such that the emitted light is adversely affected - Tinted (4.4.1 (b) (ii)) | 1 |
| Nearside Rear Inner Road wheel badly distorted (5.2.2 (c) (i)) | 1 |
| Nearside Rear coil spring cracked (2.4.C.1a) | 1 |
| Front position lamp(s) incorrect colour (1.1.A.3e) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak tail pipe missing |8.2.1.1 |b|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Nearside rear inner wheel arch and offside rear inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength above wheel (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength behind wheel (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced above wheel (7.1.1 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage insecurely attached broke (5.3.3 (a) (i)) | 1 |
| Brake master cylinder leaking hydraulic fluid |3.6.G.1f| | 1 |
| Nearside Front Anti-roll bar linkage has an unsafe modification Lock nut loose (5.3.3 (c) (i)) | 1 |
| Offside Front Anti-roll bar linkage has an unsafe modification Lock nut loose (5.3.3 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill heavily corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light white light (4.5.4 (a)) | 1 |
| Offside Front Steering locking device missing track rod end (2.1.3 (d)) | 1 |
| Nearside Front Steering locking device missing track rod end (2.1.3 (d)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill panel (6.1.1 (c) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (emission teas failed) (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (emissions test failed) (8.2.1.2 (b)) | 1 |
| Central Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s rear sill |6.1.B.2| | 1 |
| Rear coil spring broken |2.4.C.1a| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded inner wheel arch (1.1.21 (e) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch corroded and holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch at front (7.1.1 (a) (i)) | 1 |
| Nearside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Rear sill panel |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Rear sill panel |5.2.6| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced 6 x places (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced 6 x places (6.1.1 (c) (i)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure is fractured and structural rigidity is significantly reduced inner and outer sill at front wheel well (6.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure is fractured and structural rigidity is significantly reduced inner and outer at front wheel well (6.1.1 (a) (i)) | 1 |
| Offside Integral body structure is fractured and structural rigidity is significantly reduced inner sill around half way between wheel wells (6.1.1 (a) (i)) | 1 |
| Offside Rear Integral body structure is fractured and structural rigidity is significantly reduced holed at rear wheel well, inner and outer sill and wheel well all missing (6.1.1 (a) (i)) | 1 |
| Front Position lamp switch does not operate in accordance with the requirements both front lamps (4.2.2 (a)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced REAR INNER WINGS (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced REAR INNER WINGS (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis hole (5.3.3 (b) (i)) | 1 |
| Offside Front Brake hose connection leaking on an air braking system |1.1.12 |c| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis section section |2.4.A.3| | 1 |
| Nearside Body component damaged and likely to cause injury mirror (6.2.1 (a) (i)) | 1 |
| Nearside Rear Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Offside Rear Battery insecure and likely to fall from carrier battery compartment corroded excessively (4.13 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting fractured chassis rail (5.3.3 (b) (ii)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting fractured chassis rail (5.3.3 (b) (ii)) | 1 |
| Offside Rear Macpherson strut mounting corroded and seriously weakened inner wheel arch (5.3.3 (b) (i)) | 1 |
| Nearside Rear Macpherson strut mounting corroded and seriously weakened inner wheel arch (5.3.3 (b) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced anti roll bar mount |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced anti roll bar mount |6.1.1 |c| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch suspension area |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch suspension area |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under inner sill |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis Rail Corroded and Holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill / wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis has excessive corrosion/damaged |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis has excessive corrosion/damaged |6.1.B.2| | 1 |
| Emissions not tested Poor running (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Behind headlight above Outer chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Behind headlight above Outer chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength In boot (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength In boot (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill inner - outer (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill inner - outer (6.1.1 (c) (i)) | 1 |
| Emissions not tested poor running (8.2.1.2 (d)) | 1 |
| Suspension component mounting prescribed area is excessively corroded Both sills at rear |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing area. (5.3.6 (a) (i)) | 1 |
| Offside Front rear brake grabbing severely |3.7.A.5b| | 1 |
| Offside Rear Brake lever has abnormal movement of levers indicating excessive wear calliper parking brake lever |3.5.1f| | 1 |
| Offside Rear Brake linkage has abnormal movement of levers indicating maladjustment |3.5.1f| | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid Caliper |3.6.A.1| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor pan of |6.1.B.2| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded sill corroded & holed in prescribed area of seat mount |5.2.6| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded sill corroded & holed in prescribed area of seat mount |5.2.6| | 1 |
| Front Anti-roll bar linkage pin or bush excessively worn x two (5.3.4 (a) (i)) | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis around anti roll bar mounting |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis around anti roll bar mounting |2.4.A.3| | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak hc very high (8.2.2.1 (b)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill and floor has heavy corrosion / with 30cm of seat belt (7.1.1 (a) (i)) | 1 |
| Nearside Rear Axle swivel pins and bushes swivel pin and/or bush excessively worn |5.1.2 |b| |i|| | 1 |
| Offside Rear Axle swivel pins and bushes swivel pin and/or bush excessively worn |5.1.2 |b| |i|| | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |1.8.B.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CENTRE SILL (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ARCH FRONT & BACK (5.3.6 (a) (i)) | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sil |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings front and rear sill |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Inner wing |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded Inner wing |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill section |2.4.A.3| | 1 |
| Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting both sides (6.2.2 (d) (i)) | 1 |
| Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting both sides (6.2.2 (d) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer holed, rest of system has slight leaks |7.1.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sills holoed |5.2.6| | 1 |
| Nearside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings no fully seam welded |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner quarter |6.1.B.2| | 1 |
| Central Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner quarter |6.1.B.2| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded arch |5.2.6| | 1 |
| Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both inner sills and n/s boot floor |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor, marked with chalk (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor, marked with chalk (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill, marked with chalk (6.1.1 (c) (i)) | 1 |
| Front Brake disc significantly and obviously worn BOTH (1.1.14 (a) (i)) | 1 |
| Rear Brake disc significantly and obviously worn BOTH (1.1.14 (a) (i)) | 1 |
| Offside Front Front position lamp|s| has less than 50% of the light sources illuminating side light |1.1.A.3b| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Anti-roll bar linkage fractured o/s/f drop link broken (5.3.3 (b) (ii)) | 1 |
| Hydraulic brake calliper leaking and braking performance affected offside rear caliper leaking fluid (1.1.16 (b) (ii)) | 1 |
| Offside Rear Outer Vehicle structure is fractured and structural rigidity is significantly reduced sill (6.1.1 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg in wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Steering locking device missing (2.1.3 (d)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Arch |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Arch |7.1.1 |a| |i|| | 1 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| touching wheel |2.2.D.2b| | 1 |
| Nearside Rear All direction indicators not working |4.4.1 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 1 |
| Nearside Front Torsion bar fractured |2.4.E.1a| | 1 |
| Emissions not tested exhaust leak giving false fail (8.2.2.2 (e)) | 1 |
| Rear Exhaust has a major leak of exhaust gases flanges corroded middle to rear section (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing under fuse box (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch holed (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch holed in several places (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail. (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg near anti-roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting cracked link arm |2.4.G.1| | 1 |
| Offside Parking brake inoperative on one side no effort (1.4.1 (a)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sil (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sil (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sil (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sil (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sil (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sil (6.2.2 (d) (i)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system before rear axel. Brake test not completed (1.1.11 (b) (ii)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg inside wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage insecure separated |2.4.G.1| | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced offside inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassi leg |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassi leg |6.1.B.2| | 1 |
| Stop lamp not working Mid Brake Light Inop |1.2.1b| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| front brake binding both front |3.7.B.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Floor and inner sill excessively corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail near anti roll bar mounting. (5.3.6 (a) (i)) | 1 |
| Body has a projection caused by corrosion nearside and offside outer sills corroded |6.1.C.1| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill and where wheel arch meets sill |6.1.B.2| | 1 |
| Offside Rear Lower Vehicle structure is fractured and structural rigidity is significantly reduced Inner sill (6.1.1 (a) (i)) | 1 |
| Offside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Integral body structure is fractured and structural rigidity is significantly reduced Near boot floor area (6.1.1 (a) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Near boot floor area (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure is fractured and structural rigidity is significantly reduced Inner wheel arch upper area (6.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure is fractured and structural rigidity is significantly reduced Inner wheel arch upper area (6.1.1 (a) (i)) | 1 |
| Steering column universal joint has excessive play |2.1.5| | 1 |
| Offside Front Suspension component attachment bracket/mounting likely to become detached Shock absorber mounting bracket on suspension arm excessively corroded. (5.3.3 (a) (ii)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Rear sills both sides (6.1.1 (c) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced Sills both sides (7.1.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage likely to become detached |5.3.3 |a| |ii|| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits 1.175 |7.3.D.3| | 1 |
| Nearside Front Supplementary Restraint System warning lamp indicates a fault |5.4.2| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis ( roll bar bracket ) (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper suspension arm mounting point (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced n/s/r outer sill holed (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is inadequately repaired n/s/r outer sill covered by tape but still holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Behind wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected in front of rear arch (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected in front of rear arch (5.3.6 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength By a/roll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Centre Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Rear Stop lamp|s| not working centre |4.3.1 |a| |ii|| | 1 |
| Nearside Rear Sub-frame insecurely attached |5.3.3 |a| |i|| | 1 |
| Offside Rear Road wheel fixing missing wheel nut |5.2.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor to sill area |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded under body to sill backing area |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded under body area to floor |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded under body area to floor |5.2.6| | 1 |
| Nearside brake disc in such a condition that it is seriously weakened metal to metal !! |3.5.1i| | 1 |
| Rear Exhaust has a major leak of exhaust gases box joints (6.1.2 (a)) | 1 |
| Emissions not tested due to exhaust (8.2.1.2 (d)) | 1 |
| Offside Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak centre and front pipe areas (8.2.1.1 (b)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength chassis rear sub frame mounting (5.3.6 (a) (i)) | 1 |
| Brake pipe at imminent risk of failure or fracture front to rear |1.1.11 |a|| | 1 |
| Nearside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Offside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded floor/inner arch |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner arch/inner sill |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases center |6.1.2 |a|| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Brake pipe leaking on an air braking system Front to rear |1.1.11 |b| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Brake performance not tested fluid leak |1.2.1 |g|| | 1 |
| Power steering component|s| leaking metal pipe |2.3.3b| | 1 |
| Seat belt anchorage prescribed area is excessively corroded rear of near side sill panel area |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill as marked |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill floor area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper rear section of inner wheel arch excessively corroded |5.3.6 |a| |i|| | 1 |
| Emissions unable to be completed co excessively high (8.2.1.2 (d)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper wheel arch (5.3.6 (a) (i)) | 1 |
| Centre Rear Electrical wiring insecure underside earth cable |1.9.2a| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill/ wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill / wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Rear Outer Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill/ wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Body component corroded and likely to cause injury Sill (6.2.1 (a) (i)) | 1 |
| Offside Rear Outer Body component corroded and likely to cause injury Sill (6.2.1 (a) (i)) | 1 |
| Offside Front Window in an unacceptable condition quarter light window |3.2 |c| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing area. |5.3.6 |a| |i|| | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced both outer sills |7.1.1 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor pan (5.3.6 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure is fractured and structural rigidity is significantly reduced Inner sill (6.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Next to anti roll bar |2.4.A.3| | 1 |
| Offside Front Vehicle structure is fractured and structural rigidity is significantly reduced 2x holes either side of mounting (6.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure is fractured and structural rigidity is significantly reduced 2x holes by mounting (6.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corner (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded Sill / sill end |5.2.6| | 1 |
| Nearside Rear Floor excessively deteriorated N/S/R Boot floor pan corroded. (6.2.4 (a) (i)) | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits 1.094 |7.3.D.3| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering floor |6.1.A.1| | 1 |
| Nearside Front Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.A.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing behind wheel (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis behind wheel |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis behind wheel |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering ns front chassis leg holed and corroded (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering os chassis leg holed and corroded (6.1.1 (c) (ii)) | 1 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (sill) (6.1.1 (c) (i)) | 1 |
| Passenger`s airbag obviously defective |5.4.1| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Battery tray (6.1.1 (c) (i)) | 1 |
| Headlamp incorrect colour (4.1.4 (a)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg | under bonnet | |6.1.1 |c| |i|| | 1 |
| Power steering pipe|s| or hose|s| leaking across subframe |2.3.3b| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded chassis out rigger holed and corroded |5.2.6| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor |6.2.2 |d| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor |6.2.2 |d| |i|| | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn bottom ball joint. (5.3.4 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill area badly corroded as marked in yellow chalk. (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area badly corroded within 30cm of suspension componant. (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Sill. |5.2.6| | 1 |
| Towbar attachment insecure (6.1.6 (c) (i)) | 1 |
| Front Direction indicator adversely affected by the operation of another lamp fog lights. (4.4.3 (b)) | 1 |
| Rear Exhaust has a major leak of exhaust gases join - gasket not sealing |7.1.2| | 1 |
| Nearside Headlamp aim beam image obviously incorrect suspect bulb incorrectly fitted |1.8.A.1b| | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill area |7.1.1 |a| |i|| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill area |7.1.1 |a| |i|| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor holed |6.1.B.2| | 1 |
| Nearside Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Front Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill corrosion marked yellow |6.1.B.2| | 1 |
| Nearside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor and inner cill corrosion marked yellow |6.1.B.2| | 1 |
| Rear Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.D.1| | 1 |
| Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Position lamp not working both front |4.2.1 |a|| | 1 |
| Offside Rear Brake linkage has restricted free movement |1.1.15 |e|| | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired SILL (6.2.2 (d) (ii)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting CHASSIS (6.2.2 (d) (i)) | 1 |
| Central Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 1 |
| Offside Front Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill/arch |5.2.6| | 1 |
| Nearside Front Inner Suspension spring mounting prescribed area is excessively corroded wing |2.4.A.3| | 1 |
| Offside Rear Braking system leaking metal brake pipe |3.6.A.1| | 1 |
| Offside Rear Tie bar/rod attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Power steering pipe|s| or hose|s| fouling other parts of the vehicle From pump to rack. |2.3.2| | 1 |
| Service brake is causing the vehicle to swerve to the offside |3.7.C.2| | 1 |
| Offside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Rear Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Rear Fuel tank leaking |7.2.3| | 1 |
| Offside Front Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 1 |
| Offside Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under rear arch |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under rear arch |7.1.1 |a| |i|| | 1 |
| Offside Front Wheel nut(s) missing (4.2.A.1e) | 1 |
| Offside Front All position lamps not working (1.1.A.3b) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Front brake disc excessively pitted (3.5.1h) | 1 |
| Nearside Front Side repeater missing (1.4.A.2b) | 1 |
| Front Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4) | 1 |
| Emissions unable to be completed Due to alternator belt missing (8.2.1.2 (d)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded |7.1.1 |a| |i|| | 1 |
| Power steering pipe/hose leaking pipe |2.1.5 |a|| | 1 |
| Emissions not tested vehicle won`t rev |8.2.1.2 |d|| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded rear of outer sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded rear of outer sill |5.2.6| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both rear inner & outer sills (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Both rear inner wheel arches (6.1.1 (c) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Outer sill holed |2.4.A.3| | 1 |
| Nearside Rear Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Nearside Front Anti-lock braking system component excessively damaged |3.4.2| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced back inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Arch area can be seen from behind wheel. (6.1.1 (c) (i)) | 1 |
| Central Front Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Road wheel more than one fixing missing one stud missing from each wheel (5.2.1 (a) (ii)) | 1 |
| Offside Rear Body has an unsafe modification sill holed (6.2.1 (d) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Nearside Rear Lower Suspension arm fractured |5.3.3 |b| |ii|| | 1 |
| Brake performance not tested Unsafe to check due to suspention arm |1.2.1 |g|| | 1 |
| Offside Front Floor excessively deteriorated floor-inner sill (6.2.4 (a) (i)) | 1 |
| Offside Front Brake hose damaged and likely to fail rubbing on wishbone on full lock (1.1.12 (a)) | 1 |
| Nearside Front Brake pipe excessively chafed |3.6.B.2c| | 1 |
| Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction item hanging from rear view mirror |3.1 |a| |ii|| | 1 |
| Oil leaking excessively from engine engine oil leak (8.4.1 (a) (i)) | 1 |
| Front Body has a sharp edge caused by damage plate holder damaged sharp edges |6.1.C.1| | 1 |
| Nearside Rear Brake pipe connection leaking on a hydraulic braking system Connection between caliper and brake hose leaking |1.1.11 |b| |ii|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting excessive corrosion to sill |6.2.2 |d| |i|| | 1 |
| Offside Rear Lower Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Battery insecure floor corroded |1.9.1| | 1 |
| Offside Rear Outer Body panel corroded and likely to cause injury wheel arch/ quarter panel (6.2.1 (a) (i)) | 1 |
| Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Service brake excessively binding Both front (1.2.1 (f)) | 1 |
| Nearside Rear Seat belt anchorage likely to become detached in the event of a collision rear inner wheel arch excessively corroded (7.1.1 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage likely to become detached in the event of a collision inner wheel arch excessively corroded (7.1.1 (a) (ii)) | 1 |
| Emissions oxygen sensor obviously defective (8.2.1.1 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill corroded (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure is deformed and structural rigidity is significantly reduced chassis rail damaged (6.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure is deformed and structural rigidity is significantly reduced chassis rail damaged (6.1.1 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Rear Outer Body panel corroded and likely to cause injury Wheel arch |6.2.1 |a| |i|| | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Front Outer Body component corroded and likely to cause injury Wheel arch |6.2.1 |a| |i|| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill |6.2.2 |d| |i|| | 1 |
| Offside Front Outer Body component corroded and likely to cause injury Wheel arch |6.2.1 |a| |i|| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush linkpin |2.4.G.2| | 1 |
| Exhaust has a major leak of exhaust gases at rear silencer |7.1.2| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Tie bar/rod ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Front Position lamp not working both |4.2.1 |a|| | 1 |
| Offside Rear fog lamp does not emit a steady red light requires red bulb |4.5.4 |a|| | 1 |
| Front Lower Suspension arm ball joint excessively worn BOTH SIDES |5.3.4 |a| |i|| | 1 |
| Offside Rear Upper Anti-roll bar ball joint excessively worn link bar |5.3.4 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut tower (5.3.6 (a) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases centre flange meets rear section (6.1.2 (a)) | 1 |
| Offside Front brake caliper securing device missing |3.5.1j| | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill 2x holes (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis - (boot floor) (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis - (boot floor) (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inside arch (7.1.1 (a) (i)) | 1 |
| Offside Front Brake performance not tested brake caliper seized |1.2.1 |g|| | 1 |
| Rear Anti-roll bar cracked |2.4.G.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outersill |2.4.A.3| | 1 |
| Exhaust system insecure Centre bracket snapped (6.1.2 (a)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis to jacking point (6.1.1 (c) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn Fluctuation across axle (1.1.14 (a) (i)) | 1 |
| Offside Rear Exhaust system insecure Rubber mounting missing (6.1.2 (a)) | 1 |
| Nearside Front Brake disc significantly and obviously worn Fluctuation across axle (1.1.14 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Inner & Outer body sills (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Outer body sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Siil holed and weak |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill panel |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed |7.1.1 |a| |i|| | 1 |
| Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Front Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis wheel arch area |6.1.1 |c| |i|| | 1 |
| Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill areas (7.1.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering inner and outer sill (6.1.1 (c) (ii)) | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering inner and outer sill (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Position lamp not working replaced 501 bulb (4.2.1 (a) (ii)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill marked with chalk (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill , marked with chalk (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill. marked with chalk (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension arm corroded and seriously weakened lower suspension arm corroded, marked with chalk (5.3.3 (b) (i)) | 1 |
| Front Position lamp not working both front 501 capless bulbs replaced (4.2.1 (a) (ii)) | 1 |
| Nearside Front Electrical wiring insecure |1.9.2a| | 1 |
| Offside Front Electrical wiring insecure |1.9.2a| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 1 |
| Nearside Front Track rod end modified such that the steering is adversely affected (2.1.3 (f) (ii)) | 1 |
| Offside Front Brake hose stretched |3.6.B.4c| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis by roll bar mounting point (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/inner arch by roll bar mounting point (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to floor corroded & holed |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to floor & outer sill corroded & holed |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill Area |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill Area |7.1.1 |a| |i|| | 1 |
| Nearside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end cap to axle mounts (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end cap to axle mounts (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar insecure and impairing directional stability Rotten (5.3.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis Leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Inner Arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Arch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Arch (5.3.6 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Middle Of Sill To Floor (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded upper suspension arm mounting area |2.4.A.3| | 1 |
| Offside Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill and floor holed and corroded |5.2.6| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg holed and corroded heavily |6.1.B.2| | 1 |
| Offside Rear Suspension arm worn and seriously weakened lower arm hold and corroded |2.4.G.1| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill to floor hold and corroded |5.2.6| | 1 |
| Offside Rear Battery insecure and likely to fall from carrier floor heavily holed and corroded (4.13 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor and inner and outer sills heavily holed and corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg holed and corroded (6.1.1 (c) (ii)) | 1 |
| Nearside Front Body panel insecure outer wing (6.2.1 (a) (i)) | 1 |
| Emissions not tested exhaust leaking (8.2.1.2 (d)) | 1 |
| Nearside Front Power steering component fouling under tray |2.1.5 |e| |i|| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded Chassis rail |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mounting on chassis rail |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases rear section (6.1.2 (a)) | 1 |
| Offside Front Floor excessively deteriorated 3 places (6.2.4 (a) (i)) | 1 |
| Nearside Front Floor excessively deteriorated floor inner sill area (6.2.4 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area is excessively corroded chassis rails at front anti roll bar |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under bonnet top of inner arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner & outer sills (7.1.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor and chassis rail (6.1.1 (c) (i)) | 1 |
| Nearside Rear Upper Suspension component pin or bush excessively worn hub to wishbone (5.3.4 (a) (i)) | 1 |
| Parking (secondary brake) on a single line braking system has inadequate effort at a wheel Both wheels (1.3.1 (a) (i)) | 1 |
| Nearside Front Lower Suspension rod ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension rod ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s/r sil (6.2.2 (d) (i)) | 1 |
| Nearside Headlamp not working on dipped beam (poor connection) (4.1.1 (a) (ii)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings By subframe mouting |6.1.B.2| | 1 |
| Offside Rear Anti-lock braking system component excessively damaged |3.4.2| | 1 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill corroded (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill corroded (6.1.1 (c) (i)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill corroded (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Forward chassis leg, visible through wheel arch. (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Forward chassis leg, visible through wheel arch. (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nearside rear sill (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed due to exhaust leak (8.2.1.2 (d)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure inadequately repaired such that structural rigidity is significantly reduced inner sill (6.1.1 (d) (i)) | 1 |
| Offside Front Floor excessively deteriorated Small hole caused by corrosion. (6.2.4 (a) (i)) | 1 |
| Nearside Floor excessively deteriorated Small hole caused by corrosion. (6.2.4 (a) (i)) | 1 |
| Offside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill rotted (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill rotted (7.1.1 (a) (i)) | 1 |
| Driver`s airbag obviously inoperative warning light on |7.1.5 |c|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner arch upper (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor/ sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor/ sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner/ outer sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced chassis rail (7.1.1 (a) (i)) | 1 |
| Emissions not tested centre and rear silencer missing (8.2.1.2 (d)) | 1 |
| Offside Front Anti-roll bar modified so the suspension is likely to fail other components contacting upper suspension arm (5.3.3 (c) (ii)) | 1 |
| Nearside Rear Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced holes in weld for outer sill repair (6.1.1 (d) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front of rear wheel arch, back of sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front of rear wheel arch, back of sill (6.1.1 (c) (i)) | 1 |
| Central Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
| Central Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Central Rear fog lamp does not face the rear |4.5.4 |a|| | 1 |
| Offside Front Body has a sharp edge caused by corrosion outersill |6.1.C.1| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion boot compartment |under car| |6.1.C.1| | 1 |
| Exhaust has a major leak of exhaust gases centre pipe into cat split (6.1.2 (a)) | 1 |
| Emissions unable to be completed Due to exhaust blow (8.2.1.2 (d)) | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both rear sills inside |6.1.B.2| | 1 |
| Offside Front Front position lamp|s| missing |1.1.A.3a| | 1 |
| Stop lamp not working HIGH LEVEL BRAKE LAMP |1.2.1b| | 1 |
| Nearside Rear Brake linkage excessively worn |1.1.15 |b|| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill/arch (6.1.1 (c) (i)) | 1 |
| Suspension component mounting prescribed area is inadequately repaired Nearside boot area (5.3.6 (a) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Boot Floor area (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis Rail (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis Rail (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill and floor |5.2.6| | 1 |
| Nearside Rear Upper Seat belt anchorage prescribed area is excessively corroded arch |5.2.6| | 1 |
| Offside Rear Upper Seat belt anchorage prescribed area is excessively corroded arch |5.2.6| | 1 |
| Front All position lamps not working both |4.2.1 |a|| | 1 |
| Nearside Front Outer Vehicle structure is deformed and structural rigidity is significantly reduced chassis rail |6.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded lower sill area |5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases tail joint |7.1.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under back wing floor |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing |5.3.6 |a| |i|| | 1 |
| Offside Rear Anti-roll bar insecurely attached fouling body |5.3.3 |a| |i|| | 1 |
| Anti-roll bar has excessive play in a ball joint nsf and also rear |2.4.G.2| | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired rear of outer sill |5.2.6| | 1 |
| Central Rear brake caliper has restricted free movement |3.5.1k| | 1 |
| Nearside Front Upper Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing (6.2.2 (d) (i)) | 1 |
| Offside Front Upper Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing (6.2.2 (d) (i)) | 1 |
| Nearside Rear Upper Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chalked in yellow (6.2.2 (d) (i)) | 1 |
| Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting chassis (6.2.2 (d) (i)) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting chassis (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength boot floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint likely to become detached snaped (5.3.4 (a) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear portions of nearside and offside sills corroded and weakened. |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded valance |2.4.A.3| | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Side repeater missing (4.4.1 (a) (ii)) | 1 |
| Rear Exhaust particulate filter missing where one was fitted as standard back box (8.2.2.1 (a)) | 1 |
| Nearside Subframe mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Rear Brake cable guide defective and affecting operation |1.1.15 |d|| | 1 |
| Front Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
| Nearside Front Front suspension locking device missing Upper suspension arm ball joint split pin |locking device| missing |2.5.A.4| | 1 |
| rear brake recording little or no effort Both sides |3.7.B.5a| | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill |6.2.2 |d| |i|| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill |6.2.2 |d| |i|| | 1 |
| Nearside Front Road wheel more than one fixing loose |5.2.1 |a| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill corroded/holed |5.2.6| | 1 |
| Offside Front Anti-roll bar locating pin insecure |2.4.G.3a| | 1 |
| Nearside Rear Braking system leaking brake caliper leaking |3.6.A.1| | 1 |
| Nearside Rear Outer Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Rear Inner Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL |6.1.B.2| | 1 |
| Nearside Rear brake caliper has restricted free movement TOP |3.5.1k| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch. (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch. (7.1.1 (a) (i)) | 1 |
| Fuel system component leaking fuel tank area |7.2.3| | 1 |
| Nearside Front Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected Chassis (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor |7.1.1 |a| |i|| | 1 |
| Nearside Front Inner Suspension spring mounting prescribed area is excessively corroded wing ENGINE BAY |2.4.A.3| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded BOOT FLOOR |2.4.A.3| | 1 |
| Offside Front Upper Steering retaining device missing |2.2.C.1g| | 1 |
| Offside Front Lower Steering retaining device missing |2.2.C.1g| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both sides outer sill area |6.1.B.2| | 1 |
| Nearside Front Upper Suspension arm pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Upper Suspension arm pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner chassis leg (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to sill (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner floor to sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to sill inner (6.2.2 (d) (i)) | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under driver seat |6.1.B.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wing arch |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner wing arch |5.2.6| | 1 |
| Nearside Rear Outer Body panel corroded and likely to cause injury wheel arch |6.2.1 |a| |i|| | 1 |
| Offside Rear Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering outer sill |6.1.A.1| | 1 |
| Offside Rear Braking system leaking |1.1.3 |d|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch area |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch area |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch marked |2.4.A.3| | 1 |
| Offside Front Electrical wiring insecure ABS wiring |1.9.2a| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg marked |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg marked |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill marked |5.2.6| | 1 |
| Nearside Front Headlamp aim does not move downwards when dipped |British American headlamp| |1.8.C.4| | 1 |
| Nearside Outer Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Inner Rear Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing | under wing| |2.4.A.3| | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting flitch |6.2.2 |d| |i|| | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Rear Brake hose leaking on a hydraulic braking system |1.1.12 |c| |ii|| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner arch/inner wing (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner arch/inner wing (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill to floor (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill to floor (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Offside Rear Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Offside Front Vehicle structure inadequately repaired such that structural rigidity is significantly reduced inner sill (6.1.1 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg by subframe mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer quarter panel rusted and holed (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor/sill lip rusted and holed (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor/sill lip rusted and holed (7.1.1 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak rear silencer joint blowing (8.2.1.1 (b)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor rusted and holed |7.1.1 |a| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting area behind rear wheel, corroded and holed (6.2.2 (d) (i)) | 1 |
| Emissions not tested rear silencer leaking |7.4.B.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis rail by sub frame mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner body sill area (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Rear silencer (6.1.2 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer body sill area where marked (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area where marked (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area where marked (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn lower ball joint (5.3.4 (a) (i)) | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings battery |6.1.B.2| | 1 |
| Offside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings battery carrier |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering under wheel arch |6.1.1 |c| |ii|| | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sil |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sil |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outter sil |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sil |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outter sil |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing behind headlamp area |2.4.A.3| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover missing |2.4.G.2| | 1 |
| Centre Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Floor |6.1.A.1| | 1 |
| Fuel system component leaking injector |7.2.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced flooring to sill (6.1.1 (c) (i)) | 1 |
| Rear Suspension arm fractured lower both sides (5.3.3 (b) (ii)) | 1 |
| Front Suspension component mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected both sides near turret tops and inner wings (5.3.6 (a) (ii)) | 1 |
| Suspension component mounting prescribed area fractured significantly reducing structural strength both inner sills multiple holes (5.3.6 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area fractured significantly reducing structural strength both sides chassis rails near roll bar mounts (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area fractured significantly reducing structural strength both outer sills (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength battery tray and floor (5.3.6 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rails (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti rollbar mount |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded cill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded cill |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded cill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded cill |5.2.6| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Front Outer Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Nearside Rear coil spring broken upper coil |2.4.C.1a| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg at antirole bar mount |5.3.6 |a| |i|| | 1 |
| Offside Front Steering locking device missing track rod end split pin |2.2.C.1g| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded Inner Sill |5.2.6| | 1 |
| Offside Front coil spring worn so that its cross sectional area is reduced and seriously weakened |2.4.C.1b| | 1 |
| Central Floor excessively deteriorated Nearside excessive corrosion (6.2.4 (a) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner center floor |6.2.2 |d| |i|| | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor |6.2.2 |d| |i|| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill |6.1.B.2| | 1 |
| Offside Rear Battery insecure and likely to fall from carrier BOTTOM OF CARRIER HOLED (4.13 (a) (ii)) | 1 |
| Nearside Front Track rod end ball joint dust cover missing (2.1.3 (g) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded CHASSIS LEG |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded CHASSIS LEG |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Nearside Front Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner and outer sill structure |6.2.2 |d| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner and outer sill structure |6.2.2 |d| |i|| | 1 |
| Nearside Power steering pipe/hose leaking Hose to metal pipe excessively. (2.1.5 (a)) | 1 |
| Nearside Front Lower Steering linkage ball joint ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Lower Steering linkage ball joint ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor/arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg under driver |6.1.1 |c| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced area excessively corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting corroded at chassis outrigger (6.2.2 (d) (i)) | 1 |
| Offside Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill marked yellow |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill marked yellow |2.4.A.3| | 1 |
| Offside Lower Front suspension locking device missing |2.5.A.4| | 1 |
| Nearside Front Inner Body panel corroded and likely to cause injury outer sill (6.2.1 (a) (i)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury sill (6.2.1 (a) (i)) | 1 |
| Offside Front Inner Body panel corroded and likely to cause injury outer sill (6.2.1 (a) (i)) | 1 |
| Central Vehicle structure is fractured and structural rigidity is significantly reduced near side chassis holed |6.1.1 |a| |i|| | 1 |
| Rear Anti-roll bar linkage pin or bush excessively worn both |5.3.4 |a| |i|| | 1 |
| Offside Front Side repeater insecure |1.4.A.2b| | 1 |
| Front brake disc modified and seriously weakened |3.5.1n| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both rear towing eyes |6.1.B.2| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded floor too sill |5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases joint - both parts rotten |7.1.2| | 1 |
| Front Brake disc significantly and obviously worn n/s & o/s (1.1.14 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing flitch (5.3.6 (a) (i)) | 1 |
| Braking system leaking front to rear |3.6.A.1| | 1 |
| Inner Rear brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Front Upper Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis outrigger |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis outrigger |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering FLITCH PANEL HOLED |6.1.1 |c| |ii|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength flitch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength undersill/flitch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner flitch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail/inner flitch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner flitch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail/inner flitch (5.3.6 (a) (i)) | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits 1.06 |7.3.D.3| | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting insecure and impairing directional stability |5.3.3 |a| |ii|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body (5.3.6 (a) (i)) | 1 |
| Nearside Front Shock absorber insecure lower bolt |2.7.2b| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint knocking when driven |2.4.G.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering +centre+rear floor/sill edge |6.1.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis close to anti roll bar mountings |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis close to anti roll bar mountings |2.4.A.3| | 1 |
| Subframe mounting prescribed area is excessively corroded nsf and osf chassis rails |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded osf and nsf chassis rails/ by anti roll bar mounts |2.4.A.3| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded inner wing x2 |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded inner wing x2 |2.4.A.3| | 1 |
| Offside Front Anti-roll bar linkage synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired Outer sill not welded (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis/ anti roll bar mounting |2.4.A.3| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mounting |2.4.A.3| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded outer sill section |5.2.6| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded inner sill section |5.2.6| | 1 |
| Nearside Rear brake caliper leaking at parking brake spindle |3.6.A.1| | 1 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 1 |
| Nearside Floor insecure rear battery tray (6.2.4 (a) (i)) | 1 |
| Offside Rear Floor insecure (6.2.4 (a) (i)) | 1 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded rear of outer sill |5.2.6| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits exhaust blowing (8.2.1.2 (c)) | 1 |
| Emissions not tested emission test aborted due engine temperature (8.2.1.2 (d)) | 1 |
| Nearside Rear Lower Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sil |6.1.B.2| | 1 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sil |6.1.B.2| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sil |6.1.B.2| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sil |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis holed |6.1.B.2| | 1 |
| coil spring fractured |2.4.C.1a| | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Horn not working Not working with headlamps on . (7.7 (a)) | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded floor to sill |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded floor to sill |2.4.A.3| | 1 |
| Braking system leaking front to rear steel brake pipe |3.6.A.1| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Strut top mount |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Strut top mount |2.4.A.3| | 1 |
| Offside Front Anti-roll bar insecure anti-roll bar link top ball joint not attached |2.4.G.1| | 1 |
| Front position lamp|s| not working n/s and o/s |1.1.A.3b| | 1 |
| Offside Front Headlamp are incorrectly positioned (4.1.4 (a)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill |6.2.2 |d| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sil and jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is inadequately repaired wheel housing |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Inner siil/Inner arch |2.4.A.3| | 1 |
| Service brake has no recorded effort at a wheel all four wheels (1.2.1 (a) (ii)) | 1 |
| Offside Front Anti-roll bar linkage likely to fail |5.3.3 |b| |ii|| | 1 |
| Nearside Front Vehicle structure is fractured and structural rigidity is significantly reduced chassy near strut top (6.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassy near strut top (6.1.1 (c) (i)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced suspension arm (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced suspension arm (6.1.1 (c) (i)) | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings os sill and chassy leg |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch/chassis area |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch/chassis area |5.3.6 |a| |i|| | 1 |
| Power steering component|s| leaking rack |2.3.3b| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings towing mount |6.1.B.2| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner & outer sills |5.2.6| | 1 |
| Brake pipe leaking main to rear |3.6.A.1| | 1 |
| Nearside Rear Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis/wing under bonnet |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded chassis leg |5.2.6| | 1 |
| Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Suspension component mounting prescribed area is excessively corroded bottom of off side front chassis rail badly rusted |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is fractured bottom of near side front chassis rail |2.4.A.3| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive not tested |7.3.D.3| | 1 |
| brake caliper leaking n/s rear |3.6.A.1| | 1 |
| Nearside Rear Inner Body component corroded and likely to cause injury sill holed (6.2.1 (a) (i)) | 1 |
| Offside Front Brake drum back plate insecure (1.1.14 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength nsf strut top under bonnet (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut top under bonnet (5.3.6 (a) (i)) | 1 |
| Nearside Rear Road wheel fixing loose Lock nut split (5.2.1 (a) (i)) | 1 |
| Nearside Rear Emissions not tested |7.3.A.1| | 1 |
| Offside Rear Outer Suspension arm corroded and seriously weakened rear holes buy outer bush |5.3.3 |b| |i|| | 1 |
| Central Rear Exhaust fumes entering cabin (6.1.2 (b) (i)) | 1 |
| Central Rear Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a)) | 1 |
| Emissions not tested split exhaust system from rear box (8.2.1.2 (d)) | 1 |
| Nearside Rear Upper Suspension arm corroded and seriously weakened inner |5.3.3 |b| |i|| | 1 |
| Offside Rear Upper Suspension arm corroded and seriously weakened inner |5.3.3 |b| |i|| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s outer sill holed |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings o/s outer sill holed |6.1.B.2| | 1 |
| Nearside Rear rear brake recording little or no effort no handbrake effort |3.7.B.5a| | 1 |
| Nearside Rear Outer Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting under bonnet (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting under bonnet (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch area (6.2.2 (d) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded floor to sill |2.4.A.3| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded both chassis legs |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced central inner sill |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced central inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Lower Suspension component ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases Centre silencer |6.1.2 |a|| | 1 |
| Emissions not tested excessive mechanical noise from engine - cambelt area |7.3.A.1| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Floor |5.2.6| | 1 |
| Brake pipe kinked |3.6.B.2b| | 1 |
| Offside Rear Braking system leaking PIPELINE |3.6.A.1| | 1 |
| Nearside Front Valve stem seriously misaligned |5.2.3 |j|| | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rear sill |6.2.2 |d| |i|| | 1 |
| Offside Rear Lower Suspension component pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wheelarch |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded wheelarch |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded wheelarch |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases Middle and rear |6.1.2 |a|| | 1 |
| Nearside Rear Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Supplementary Restraint System warning lamp indicates a fault air bag |5.4.2| | 1 |
| Emissions not tested no CAT no silences |7.3.A.1| | 1 |
| Nearside Front position lamp|s| not working light flickers |1.1.A.3b| | 1 |
| Front Inner Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
| Rear Inner Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage missing |5.3.3 |a| |ii|| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill |6.2.2 |d| |i|| | 1 |
| Service brake excessively binding both fdront |1.2.1 |f|| | 1 |
| Nearside Outer Integral body structure has excessive corrosion which adversely affects braking or steering sill (6.1.1 (c) (ii)) | 1 |
| Offside Outer Integral body structure has excessive corrosion which adversely affects braking or steering sill (6.1.1 (c) (ii)) | 1 |
| Nearside Inner Integral body structure has excessive corrosion which adversely affects braking or steering sill to floor (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired wheel arch (6.2.2 (d) (ii)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired wheel arch (6.2.2 (d) (ii)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill and floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired SILL. (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired SILL. (7.1.1 (a) (i)) | 1 |
| Nearside Rear Shock absorbers damaged to the extent that it does not function |5.3.2 |b|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill/arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill/wing fractured (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill back corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill back corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill back corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch near anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch near anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded strut top |2.4.A.3| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner wheel arch |2.4.A.3| | 1 |
| Offside Front Tie bar/rod fractured drop link broken |2.4.G.1| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill yellow chalked |6.2.2 |d| |i|| | 1 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened bottom arm yellow chalked |5.3.3 |b| |i|| | 1 |
| Nearside Front Power steering component|s| leaking |2.3.3b| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under wheel arch near suspension bush |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under wheel arch near suspension bush |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to chassis (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded rear of n/s outer sill panel |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded rear of o/s outer sill panel |5.2.6| | 1 |
| Nearside Rear Upper Suspension arm rubber bush deteriorated resulting in excessive movement outer |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/sill end/inner wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn lower arm front rubber bush |5.3.4 |a| |i|| | 1 |
| Nearside Rear Tie bar/rod ball joint dust cover missing |2.4.G.2| | 1 |
| Nearside Front Steering system lock to lock check twists a brake hose |2.2.D.2b| | 1 |
| Offside Front Floor excessively deteriorated CORRODED (6.2.4 (a) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced SIL (6.1.1 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D-BUSH (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn D BUSH (5.3.4 (a) (i)) | 1 |
| Offside Rear Lower Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |6.1.A.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner cill |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer cill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner cill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis around antiroll bar mounting bracket
|2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis around antiroll bar mounting bracket |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded Footwell |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Behind headlight |2.4.A.3| | 1 |
| Battery insecure main |1.9.1| | 1 |
| Battery insecure slave |1.9.1| | 1 |
| Offside Rear Floor in such a condition it is likely to cause load insecurity or instability battery tray |6.2.4 |a| |ii|| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition exhaust missing (8.1.1 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Offside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance bulb dim |1.1.A.3d| | 1 |
| Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill corroded 4 inch square |6.1.B.2| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded within prescribed area (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded within prescribed area (7.1.1 (a) (i)) | 1 |
| Offside Front Anti-lock braking system wiring excessively damaged fouling on anti roll bar link (1.6 (d)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired all around front strut , (6.2.2 (d) (ii)) | 1 |
| Emissions not tested major exhaust leak. |8.2.1.2 |d|| | 1 |
| Exhaust has a major leak of exhaust gases centre to rear box joint |7.1.2| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive suspect due to blowing exhaust |7.3.D.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill in various areas (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheelarch chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheelarch chassis (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheelarch (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Body panel insecure wing (6.2.1 (a) (i)) | 1 |
| Offside Front Front position lamp|s| obviously incorrectly positioned |1.1.A.3a| | 1 |
| Power steering pipe|s| or hose|s| leaking unable to determine exactly where leak is coming from but power steering fluid all over engine bay |2.3.3b| | 1 |
| Electrical wiring heavily deteriorated earth strap broken off on rear differential housing |4.11 |b| |ii|| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill and wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside rear brake recording little or no effort parking brake |3.7.B.5a| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded / holed within 30cm of the seat belt mount (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis sub frame mounting (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn Upper (5.3.4 (a) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill x2 (6.2.2 (d) (i)) | 1 |
| Front Brake performance unable to be tested metal to metal (1.2.1 (g)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded OUTER WHEEL ARCH... |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded oUTER WHEEL ARCH TO LOWER SILL... |5.2.6| | 1 |
| Emissions not tested excesive blow |8.2.1.2 |d|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering close to suspension mount point |6.1.A.1| | 1 |
| Emissions not tested Unable to get reading due to exhaust leak. |8.2.1.2 |d|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to sill. |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to sill. |7.1.1 |a| |i|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Floor. |5.3.6 |a| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor/sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner drop sill |5.2.6| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel |7.1.1 |a| |i|| | 1 |
| Nearside Front Service brake excessively binding WHEEL BEARING NOT TESTED (1.2.1 (f)) | 1 |
| Offside Front Service brake excessively binding WHEEL BEARING NOT TESTED (1.2.1 (f)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Near side and off side prescribed area |6.1.1 |c| |i|| | 1 |
| Rear Sub-frame attachment bracket/mounting likely to become detached Near side and off side |5.3.3 |a| |ii|| | 1 |
| Offside Rear Lower Suspension component attachment bracket/mounting likely to fail |5.3.3 |b| |ii|| | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened at shocker mounting |5.3.3 |b| |i|| | 1 |
| Offside Front Lower Shock absorbers has an excessively worn bush |5.3.2 |c|| | 1 |
| Rear Upper Suspension arm pin or bush excessively worn Near side and off side |5.3.4 |a| |i|| | 1 |
| Rear Suspension arm corroded and seriously weakened Near side and off side also central |5.3.3 |b| |i|| | 1 |
| Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Near side and off side round mounting bush metal washers corroded away |5.3.6 |a| |i|| | 1 |
| Brake performance not tested Not tested due to extent of corrosion of suspension front and rear.| possible vehicle /equipment damage| |1.2.1 |g|| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure d bracket bolt sheared off (5.3.3 (a) (i)) | 1 |
| Rear Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition box |7.1.4| | 1 |
| Nearside Brake hose inappropriately repaired |3.6.A.3| | 1 |
| Offside Brake hose inappropriately repaired |3.6.A.3| | 1 |
| Nearside Front position lamp|s| not working side light flickering |1.1.A.3b| | 1 |
| Nearside Seat belt installation anchorage insecure (10.1 (d)) | 1 |
| Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced Nearside and offside outer sills (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed Due to exhaust leak (8.2.1.2 (d)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded arm in mounting area |2.4.A.3| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded arm inner mounting area |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner anti roll bar mounting area |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner anti roll bar mountingarea |2.4.A.3| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive 0.57 o/o |7.3.D.3| | 1 |
| Emissions not tested exaust not connected (8.2.1.2 (d)) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg holed and corroded |6.1.B.2| | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill hole in (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill marked with white chalk |5.2.6| | 1 |
| Front Driver`s seat insecure |6.2.A.1| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg badly corroded and holed. (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg badly corroded and holed. (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear silencer flange badly corroded and leaking gases. (6.1.2 (a)) | 1 |
| Emissions unable to be completed due to major leak of gases. (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis Arm (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis Arm (5.3.6 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases rear exhaust joint |7.1.2| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded at rear axel bracing bars |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded anti roll bar |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded anti roll bar |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg / floor (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg / floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp insecure Both headlamp mounting damaged/broken off (4.1.1 (c)) | 1 |
| Nearside Front Headlamp aim not tested Due to headlamp unit insecure (4.1.2 (b)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OFFSIDE FRONT INNER CHASSIS RAIL (MARKED) (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner chassis rail (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp insecure (4.1.1 (c)) | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area. |6.1.B.2| | 1 |
| Rear Emissions not tested |7.3.A.1| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both sides outer sill panels |6.1.B.2| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced In sill |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced In sill |7.1.1 |a| |i|| | 1 |
| Offside Rear rear brake recording little or no effort handbrake |3.7.B.5a| | 1 |
| Offside Rear Drive shaft bearing housing insecure Mount excessively corroded away (6.1.7 (f) (i)) | 1 |
| Nearside Front Upper Shock absorbers likely to become detached (5.3.2 (a) (ii)) | 1 |
| Offside Front Headlamp insecure (4.1.1 (c)) | 1 |
| Nearside Front Upper Shock absorbers insecurely attached (5.3.2 (a) (i)) | 1 |
| Nearside Rear Upper Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Offside Front Lower Suspension component missing Ball joint split pin missing (5.3.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected On chassis leg near engine and suspension mountings. |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected On chassis leg near engine and suspension mountings. |5.3.6 |a| |ii|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Inner wheel arch within 30cm of strut top mounting. |5.3.6 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Inner wheel arch within 30cm of top strut mounting. |5.3.6 |a| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill corroded and holed. |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill corroded and holed. |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mounting (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both under sills (7.1.1 (a) (i)) | 1 |
| Suspension arm ball joint dust cover no longer prevents the ingress of dirt both top and lower (5.3.4 (b) (ii)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Rail |6.1.B.2| | 1 |
| Emissions not tested DUE TO EXHAUST LEAKING |7.3.A.1| | 1 |
| Exhaust has a major leak of exhaust gases centre & rear flanges |7.1.2| | 1 |
| Nearside Rear brake caliper leaking leaking from handbrake pivot |3.6.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg underside (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg underside (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded and holed |7.1.1 |a| |i|| | 1 |
| Rear Exhaust has a major leak of exhaust gases join between middle and tail sections (6.1.2 (a)) | 1 |
| Emissions not tested due to exhaust snapped (8.2.1.2 (d)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheelarch/chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheelarch/chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn BOTH (5.3.4 (a) (i)) | 1 |
| Nearside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Nearside Outer Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Backbox joint |6.1.2 |a|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor |6.1.1 |c| |i|| | 1 |
| Offside Front Service brake excessively binding binding (1.2.1 (f)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill riser (6.1.1 (c) (i)) | 1 |
| Rear Outer Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings both outer sills welded patches not seem welded all the way round |6.1.B.2| | 1 |
| Central Exhaust has a major leak of exhaust gases pipe after cat |7.1.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill holed and weak |5.2.6| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch/under bonnet (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill / rear arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill areas - within 30cm of seat belt mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill areas - within 30cm of seat belt mount (5.3.6 (a) (i)) | 1 |
| Offside Front Windscreen damaged and affecting the drivers view of the road 10CM DAMAGE IN ZONE A (3.2 (a) (ii)) | 1 |
| Central Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 1 |
| Offside Stop lamp(s) not working bad connection (4.3.1 (a) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded rear inner sill |5.2.6| | 1 |
| Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Front Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Under sill (5.3.6 (a) (i)) | 1 |
| Road wheel more than one fixing missing |5.2.1 |a| |ii|| | 1 |
| Offside Front Side repeater not working |4.4.1 |a| |ii|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill return (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill return (7.1.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases rear silencer major leak series of large holes drilled in (6.1.2 (a)) | 1 |
| Emissions not tested not tested due to major leak (8.2.1.2 (d)) | 1 |
| Nearside Front Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Offside Windscreen wiper blade missing |8.2.2| | 1 |
| Valve stem seriously damaged |4.1.D.1e| | 1 |
| Nearside Rear Braking system leaking pipe to flexi |3.6.A.1| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` items on interior mirror |8.3.1e| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and Outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and Outer sill (7.1.1 (a) (i)) | 1 |
| Brake fluid warning lamp illuminated level low replenished same |3.6.G.2| | 1 |
| Central Rear fog lamp not working fog light lens broken (4.5.1 (a) (ii)) | 1 |
| Offside Drivers seat with a defective structure under floor rusted hole (6.2.5 (a) (i)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect bulb incorrectly fitted (4.1.2 (c)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury outer sill corroded and held (6.2.1 (a) (i)) | 1 |
| Nearside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis member |2.4.A.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases rear silencer flange |7.1.2| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced NS Inner sill corroded (7.1.1 (a) (i)) | 1 |
| Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced lower sills both sides (7.1.1 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis /inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect aftermarket lamp fitted (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect aftermarket lamp fitted (4.1.2 (c)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie rail |5.3.6 |a| |i|| | 1 |
| Emissions not tested due to major leak of exhaust gasses |8.2.2.2 |e|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner rear sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Brake disc significantly and obviously worn inner face (1.1.14 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn inner face (1.1.14 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point / chassis (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch/chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch/chassis (5.3.6 (a) (i)) | 1 |
| Nearside Outer Rear Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Outer Rear Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear Brake disc significantly and obviously worn both side (1.1.14 (a) (i)) | 1 |
| Nearside Obligatory mirror insecure |3.3 |b| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill /floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill holed by corrosion. |5.2.6| | 1 |
| Supplementary restraint system warning lamp indicates a fault loose cable connection (7.1.6 (a)) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg holed by corrosion with in 30 cm of subframe mounting |6.1.B.2| | 1 |
| Electrical wiring insecure Earth lead on chassis broken |1.9.2a| | 1 |
| Headlamp incorrect colour both sides front (4.1.4 (a)) | 1 |
| Position lamp not working both sides front (4.2.1 (a) (ii)) | 1 |
| Suspension component corroded and seriously weakened both sides inner and outer sills (5.3.3 (b) (i)) | 1 |
| Nearside Rear Brake valve leaking (1.1.7 (d) (i)) | 1 |
| Offside Front Headlamp insecure |4.1.1 |c|| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Battery tray in boot |6.1.B.2| | 1 |
| Emissions not tested No tail pipe |7.3.A.1| | 1 |
| Nearside Front Lower Anti-roll bar linkage insecure and impairing directional stability |5.3.3 |a| |ii|| | 1 |
| Nearside Rear Braking system leaking pipe |3.6.A.1| | 1 |
| Front Sub-frame corroded and seriously weakened inner wings offside and the nearside |5.3.3 |b| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced corroded and holed |7.1.1 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint likely to become detached drop link |5.3.4 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chasis leg (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced inner sill |2.4.G.1| | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced inner and outer sill |2.4.G.1| | 1 |
| Nearside Front Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced floor |2.4.G.1| | 1 |
| Centre Rear Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Nearside Steering retaining device missing |2.2.C.1g| | 1 |
| Offside Steering retaining device missing |2.2.C.1g| | 1 |
| Nearside Front Steering arm deformed and unserviceable |2.2.C.1d| | 1 |
| Nearside Front Lower Shock absorbers has an excessively worn bush bush |5.3.2 |c|| | 1 |
| Centre Rear Braking system leaking |3.6.A.1| | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn link bar (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar ball joint excessively worn link bar (5.3.4 (a) (i)) | 1 |
| Nearside Front Upper Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Hydraulic brake calliper leaking and braking performance affected |1.1.16 |b| |ii|| | 1 |
| Offside Rear Shock absorbers insecurely attached (5.3.2 (a) (i)) | 1 |
| Nearside Rear Integral body structure modified such that structural rigidity is significantly reduced wheel arch (6.1.1 (d) (i)) | 1 |
| Offside Rear Integral body structure modified such that structural rigidity is significantly reduced wheel arch (6.1.1 (d) (i)) | 1 |
| Hydraulic fluid leaking excessively power steering (8.4.1 (a) (i)) | 1 |
| Headlamp levelling device inoperative |1.7.2| | 1 |
| Headlamp cleaning device inoperative |1.7.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassie rail |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassie rail |2.4.A.3| | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Boot floor. (5.3.6 (a) (i)) | 1 |
| Nearside Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Nearside Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Offside Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Offside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor holed (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch holed (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch holed (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch holed (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch holed (6.2.2 (d) (i)) | 1 |
| Nearside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor holed (6.2.2 (d) (i)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor holed (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill
|2.4.A.3| | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill corroded marked yellow (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer chassis rail inside front arch corroded marked yellow (6.1.1 (c) (i)) | 1 |
| Offside Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Nearside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Nearside Rear Stop lamp(s) emits other than a steady red light (4.3.3 (a) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded CHASSIS |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded both front chassis |2.4.A.3| | 1 |
| Offside Front Suspension arm corroded and seriously weakened Floor (5.3.3 (b) (i)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |under anti roll bar mount| |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis same place |6.1.B.2| | 1 |
| Offside Front coil spring broken snapped |2.4.C.1a| | 1 |
| Offside Rear coil spring broken snapped |2.4.C.1a| | 1 |
| brake caliper leaking both rear calipers |3.6.A.1| | 1 |
| Nearside Rear Anti-roll bar linkage insecurely attached nut loose (5.3.3 (a) (i)) | 1 |
| Nearside Rear Anti-lock braking system wheel speed sensor missing (1.6 (c)) | 1 |
| Offside Rear Outer Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Upper Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 1 |
| Power steering ram leaking |2.1.5 |a|| | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner cill (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner cill (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting nearside and offside chassis outriggers |6.2.2 |d| |i|| | 1 |
| Nearside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting sill |6.2.2 |d| |i|| | 1 |
| Front Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting nearside and offside wheel arch outer chassis legs |6.2.2 |d| |i|| | 1 |
| Front Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting nearside and offside wheel arch tub rear wall |6.2.2 |d| |i|| | 1 |
| Offside Rear Anti-roll bar linkage severely distorted |2.4.G.1| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering outer sill |6.1.1 |c| |ii|| | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sills |7.1.1 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired outer sill (5.3.6 (a) (i)) | 1 |
| Power steering pipe/hose damaged such that the steering is adversely affected NEAR COOLER PIPE (2.1.5 (g) (ii)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced CHASSIS BEHIND WHEEL HOLED (6.1.1 (c) (i)) | 1 |
| Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Nearside Rear Upper Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Upper Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Horn not a continuous or uniform sound |1.6.2e| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded sill area |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill area
|2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage likely to become detached in the event of a collision inner wheel arch (7.1.1 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage likely to become detached in the event of a collision inner wheel arch (7.1.1 (a) (ii)) | 1 |
| Offside Windscreen wiper blade missing |3.4 |b| |ii|| | 1 |
| Central Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component ball joint likely to become detached bolt and nut (5.3.4 (a) (ii)) | 1 |
| Offside Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Rear sill. (7.1.1 (a) (i)) | 1 |
| Nearside Rear Parking brake inoperative on one side no reading from handbrake (1.4.1 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor, sill & rear inner arch. (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor, sill & rear inner arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 1 |
| Front Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills have corroded and holed |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills have corroded and holed |7.1.1 |a| |i|| | 1 |
| Emissions not tested Ancillary belt damaged (8.2.1.2 (d)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner cill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor/inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor/ inner wing (5.3.6 (a) (i)) | 1 |
| Headlamp aim projected beam image is obviously incorrect Lens hazy (4.1.2 (c)) | 1 |
| Power steering pipe/hose leaking at rack (2.1.5 (a)) | 1 |
| Nearside Front Inner Suspension component corroded and seriously weakened arch |5.3.3 |b| |i|| | 1 |
| Rear Anti-roll bar linkage has excessive play in a pin/bush both drop links |2.4.G.2| | 1 |
| Electrical wiring deteriorated and bare wires exposed |1.9.2c| | 1 |
| Offside Headlamps matched pair are not the same shape |1.7.6| | 1 |
| Brake pedal has no servo assistance |3.3.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Braking system leaking Caliper area |3.6.A.1| | 1 |
| Exhaust has a major leak of exhaust gases broken |7.1.2| | 1 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Front Anti-roll bar ball joint dust cover missing |5.3.4 |b| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded innersill |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength MAIN CHASSIS (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength MAIN CHASSIS (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded under wheel arch |2.4.A.3| | 1 |
| Rear Outer Seat belt anchorage prescribed area is excessively corroded offside & nearside |5.2.6| | 1 |
| Offside Rear Upper Seat belt anchorage prescribed area is excessively corroded arch area |5.2.6| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill hole (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill hole (6.1.1 (c) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis inner & outer (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis inner & outer (6.1.1 (c) (i)) | 1 |
| Offside Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Exhaust has a major leak of exhaust gases between centre and rear silencer sections |7.1.2| | 1 |
| Nearside Rear Anti-roll bar linkage attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Body component corroded and likely to cause injury arch (6.2.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint broken |2.4.G.2| | 1 |
| Coil spring fractured or broken x2 springs |5.3.1 |b| |i|| | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded chassis leg within roll bar mount |2.4.A.3| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded chassis leg within roll bar mount |2.4.A.3| | 1 |
| Offside Subframe mounting prescribed area is excessively corroded chasis |2.4.A.3| | 1 |
| Nearside Outer Body has a sharp edge caused by corrosion sill |6.1.C.1| | 1 |
| Braking system leaking from off side rear caliper |3.6.A.1| | 1 |
| Exhaust has a major leak of exhaust gases Cat to centre pipe |7.1.2| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area is excessively corroded Chassis box above anti roll bar mount |2.4.A.3| | 1 |
| Offside Front Outer Suspension component mounting prescribed area is excessively corroded Chassis box above anti roll bar mount |2.4.A.3| | 1 |
| Nearside Front Steering locking device missing Track rod end (2.1.3 (d)) | 1 |
| Offside Front Steering locking device missing Track rod end (2.1.3 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer and inner sill |5.2.6| | 1 |
| Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WHEEL ARCHES BOTH SIDES (5.3.6 (a) (i)) | 1 |
| Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced WHEEL ARCHES BOTH SIDES (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL / LOWER WHEEL ARCH (5.3.6 (a) (i)) | 1 |
| Power steering pipe/hose leaking at rack |2.1.5 |a|| | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired inner sill corroded by jacking point (6.2.2 (d) (ii)) | 1 |
| Nearside Position lamp showing red light to the front |4.2.3 |a| |ii|| | 1 |
| Offside Position lamp showing red light to the front |4.2.3 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member area |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member area |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti-roll bar area |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded CHASSIS |inner wing| |2.4.A.3| | 1 |
| Central Rear Brake pipe at imminent risk of failure or fracture cross over has failed (1.1.11 (a)) | 1 |
| Central Rear Brake pipe leaking on a hydraulic braking system crossover (1.1.11 (b) (ii)) | 1 |
| Brake performance not tested due to brake pipe fail (1.2.1 (g)) | 1 |
| Nearside Front Brake disc contaminated (1.1.14 (b)) | 1 |
| Offside Front Brake disc contaminated (1.1.14 (b)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail by d bush (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch to sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor under battery (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch to sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure has excessive corrosion which adversely affects braking or steering sill |6.1.1 |c| |ii|| | 1 |
| Offside Rear Inner Integral body structure has excessive corrosion which adversely affects braking or steering sill |6.1.1 |c| |ii|| | 1 |
| Offside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Lower Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired boot floor |6.2.2 |d| |ii|| | 1 |
| Nearside Front Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill and floor |6.2.2 |d| |i|| | 1 |
| Offside Front Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill to floor |6.2.2 |d| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 12" of strut top, inner chassis under bonnet |5.3.6 |a| |i|| | 1 |
| Nearside Front Lower Suspension arm locating pin insecure |2.4.G.3a| | 1 |
| Offside Front Lower Suspension arm locating pin insecure |2.4.G.3a| | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill in two places (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch lower at rear most (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch rear most lower (6.1.1 (c) (i)) | 1 |
| Central Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced behind rear bumper (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases center to rear joint (6.1.2 (a)) | 1 |
| Nearside Front Anti-roll bar locating pin retaining device missing |2.4.G.3b| | 1 |
| Seat belt anchorage prescribed area is excessively corroded n/s/r inner wheel arch panel |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded o/s/r inner wheel arch panel |5.2.6| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Nearside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill @ jacking point (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Shock absorbers has an excessively worn bush Rose joint. (5.3.2 (c)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded Chassis leg underneath |2.4.A.3| | 1 |
| Nearside Rear Upper Braking system leaking |3.6.A.1| | 1 |
| Nearside Rear Position lamp not working side light (4.2.1 (a) (ii)) | 1 |
| Offside Front Lower Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill holed (5.3.6 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 1 |
| Speedometer cannot be illuminated. |6.7.3| | 1 |
| Offside Rear Road wheel fractured |4.2.B.1a| | 1 |
| Nearside Rear Suspension arm likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Offside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Nearside Rear Torque/reaction arm attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Nearside Rear Anti-roll bar severely distorted |2.4.G.1| | 1 |
| Front Body component damaged and likely to cause injury number plate cover sharp (6.2.1 (a) (i)) | 1 |
| Nearside Headlamp insecure bracket broken (4.1.1 (c)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill at jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill at jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill holed (7.1.1 (a) (i)) | 1 |
| Central Brake pipe leaking |3.6.A.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer/inner sill corroded |7.1.1 |a| |i|| | 1 |
| Offside Dipswitch operation does not extinguish all main beam headlamps leaving at least one pair of dipped beam headlamps |1.7.4b| | 1 |
| Nearside Front Anti-roll bar likely to become detached |5.3.3 |a| |ii|| | 1 |
| Offside Front Bumper likely to become detached fouling steering (6.1.4 (a) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor and sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor and inner rear sill (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor and outer rear sill (7.1.1 (a) (i)) | 1 |
| Emissions not tested due to poor running (8.2.1.2 (d)) | 1 |
| Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sills both sides |6.1.B.2| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill, sill end and inner wing (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill / chassis |5.2.6| | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis / inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/ inner sill etc. (5.3.6 (a) (i)) | 1 |
| Nearside Parking brake inoperative on one side very weak (1.4.1 (a)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak gasket leak (8.2.1.1 (b)) | 1 |
| Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced plates not welded (6.1.1 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Side repeater has less than 50% of the light sources illuminating |1.4.A.2c| | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen bulb in wrong |4.1.2 |a|| | 1 |
| Offside Rear Brake lever has restricted free movement on caliper |1.1.15 |e|| | 1 |
| Nearside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
| Offside Front Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Front Body has a sharp edge caused by damage number plate holder |6.1.C.1| | 1 |
| Nearside Outer Front Anti-roll bar linkage missing |2.4.G.1| | 1 |
| Offside Outer Front Anti-roll bar linkage missing |2.4.G.1| | 1 |
| Nearside Outer Steering locking device missing |2.2.C.1g| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill to floor pan (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill to floor pan area (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point/outrigger (6.1.1 (c) (i)) | 1 |
| Front Service brake excessively binding both fronts (1.2.1 (f)) | 1 |
| Brake disc significantly and obviously worn N/S and O/S fronts on inner surface worn (1.1.14 (a) (i)) | 1 |
| Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill and floor |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected outer sil |5.3.6 |a| |ii|| | 1 |
| Nearside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sil |5.3.6 |a| |ii|| | 1 |
| Offside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected outer sil |5.3.6 |a| |ii|| | 1 |
| Offside Front Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
| Nearside Front Floor excessively deteriorated front and rear floor holed in several places |6.2.4 |a| |i|| | 1 |
| Nearside Rear Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (outer sill) (6.1.1 (d) (i)) | 1 |
| Offside Rear Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (outer sill) (6.1.1 (d) (i)) | 1 |
| Front Anti-roll bar missing |2.4.G.1| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is severely distorted sill area |5.2.6| | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached insecure (5.3.4 (a) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached lower arm ball joint insecure (5.3.4 (a) (ii)) | 1 |
| Offside Front Sub-frame has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Front Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 1 |
| Nearside Rear Service brake lagging in operation |1.2.1 |d|| | 1 |
| Offside Front Front suspension locking device ineffective |2.5.A.4| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting |chassis| |5.3.6 |a| |i|| | 1 |
| Offside Rear Body component corroded and likely to cause injury wheel arch tape applied |6.2.1 |a| |i|| | 1 |
| Offside Rear Subframe mounting prescribed area excessively damaged significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Oil leaking excessively from engine level on min (8.4.1 (a) (i)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Front Vehicle structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Offside Front Service brake grabbing severely |1.2.1 |c|| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front both sides (roll bar mount) (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch area (7.1.1 (a) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Arch |6.2.2 |d| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis by anti roll bar mountin |5.3.6 |a| |i|| | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer seat belt mounting point |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 1 |
| Offside Front Body insecure lower part of wing (6.2.2 (a) (i)) | 1 |
| Nearside Front Body panel corroded and likely to cause injury lower part of wing (6.2.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top arm mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar fixing point |2.4.A.3| | 1 |
| Emissions not tested Vehicle overheating |7.3.A.1| | 1 |
| Nearside Front Service brake is causing the steering wheel to severely pull one way |3.7.C.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill has excessive corrosion (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength In the wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength In the wheel arch (5.3.6 (a) (i)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Both sides rear sections of sills (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded / holed, within 30cm of anti roll bar mountings (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded / holed, within 30cm of anti roll bar mountings (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch corroded holed (7.1.1 (a) (i)) | 1 |
| Nearside Front Body panel insecure and offside (6.2.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed |7.1.1 |a| |i|| | 1 |
| Rear Brake pipe connection leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 1 |
| Offside Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Front Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded both front chassis/inner arch |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis corroded |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis corroded |2.4.A.3| | 1 |
| Offside Front Front suspension has excessive movement at a suspension ball joint |2.5.A.1c| | 1 |
| Offside Front Headlamp light intensity severely reduced |4.1.4 |a|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill panel |7.1.1 |a| |i|| | 1 |
| Rear Lower Suspension arm corroded and seriously weakened both arms (5.3.3 (b) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Anti-roll bar mounting - both sides (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Outer Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced rear (6.1.1 (b) (ii)) | 1 |
| Offside Front Vehicle structure strengthening plate or fastening insecure rear (6.1.1 (b) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect lens clouded (4.1.2 (c)) | 1 |
| Front Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction sticker (3.1 (a) (ii)) | 1 |
| Oil leaking excessively from engine oil filter loose (8.4.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded floor/inner sill |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill rusted through (7.1.1 (a) (i)) | 1 |
| Emissions not tested Excessive leak (8.2.1.2 (d)) | 1 |
| Front Exhaust emissions likely to be affected by an exhaust leak leaking before and after the catalyst (8.2.1.1 (b)) | 1 |
| Headlamp light source and lamp not compatible LED headlights (4.1.4 (c)) | 1 |
| Exhaust has a major leak of exhaust gases Catalyst leaking at both connection points (6.1.2 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill end (7.1.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases pipe to silencer joint |7.1.2| | 1 |
| Offside Front Windscreen in such a condition that visibility through swept area is seriously affected (3.2 (c) (ii)) | 1 |
| Nearside Rear Service brake excessively fluctuating brake disc badly corroded |1.2.1 |e|| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering CHASSIS LEG |6.1.A.1| | 1 |
| Nearside Front Hydraulic brake calliper excessively weakened by corrosion |1.1.16 |d| |i|| | 1 |
| Front Position lamp light intensity significantly reduced both bulbs weak (4.2.3 (a) (ii)) | 1 |
| Nearside Rear Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak join (8.2.1.1 (b)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Drive shaft likely to become detached (6.1.7 (a) (ii)) | 1 |
| Offside Front Road wheel more than one fixing missing (5.2.1 (a) (ii)) | 1 |
| Nearside Brake cable damaged (1.1.15 (a)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Nearside Rear Drive shaft securing bolt loose (6.1.7 (a) (i)) | 1 |
| Nearside Rear Suspension arm damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Rear Suspension arm damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Front Lower Front suspension retaining device missing |2.5.A.4| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition rear silencer removed (8.1.1 (a)) | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting insecure ball joint split pin missing (5.3.3 (a) (i)) | 1 |
| Offside Front Upper Suspension arm attachment bracket/mounting insecure ball joint split pin missing (5.3.3 (a) (i)) | 1 |
| Nearside Rear Integral body structure is fractured and structural rigidity is significantly reduced inner arch repair (6.1.1 (a) (i)) | 1 |
| Nearside Outer Rear brake disc excessively pitted |3.5.1h| | 1 |
| Offside Outer Rear brake disc excessively pitted |3.5.1h| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill/floor |7.1.1 |a| |i|| | 1 |
| Nearside Front Wheel bolt|s| missing |4.2.A.1e| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis/inner arch |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner wheelarch |5.2.6| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor and sill joint |6.1.1 |c| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor and sill joint |6.1.1 |c| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer Sill Corroded & Holed (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced perforation within 30cm of lower driver seat belt mounting anchorage (7.1.1 (a) (i)) | 1 |
| Nearside Front Sub-frame corroded and seriously weakened holed |2.4.G.1| | 1 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan corroded and holed |5.3.6 |a| |i|| | 1 |
| Offside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement D-bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn drop link |5.3.4 |a| |i|| | 1 |
| Offside Front Vehicle structure has a fracture which is likely to adversely affect braking or steering chassis leg |6.1.1 |a| |ii|| | 1 |
| Nearside Rear Vehicle structure is fractured and structural rigidity is significantly reduced sill |6.1.1 |a| |i|| | 1 |
| Exhaust system insecure centre/back box |6.1.2 |a|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill, marked (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked (5.3.6 (a) (i)) | 1 |
| Offside Rear Braking system leaking caliper/hose |3.6.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill of |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill of |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail in wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail in wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill area |7.1.1 |a| |i|| | 1 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 1 |
| Offside Rear Braking system leaking brake caliper/hose area |3.6.A.1| | 1 |
| Offside Front Anti-roll bar insecure rod missing |2.4.G.1| | 1 |
| Nearside Upper Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 1 |
| Offside Upper Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 1 |
| Central Rear Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded door sill panel |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis and inner wing (5.3.6 (a) (i)) | 1 |
| Front brake drum excessively scored |3.5.1h| | 1 |
| Rear brake drum excessively pitted |3.5.1h| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill |7.1.1 |a| |i|| | 1 |
| Rear Exhaust has a major leak of exhaust gases JOINT (6.1.2 (a)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced LEG (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced LEG (6.1.1 (c) (i)) | 1 |
| Offside Front Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Exhaust catalytic converter missing where one was fitted as standard (7.1.3) | 1 |
| Offside Front Shock absorber has an excessively worn bush (2.7.4) | 1 |
| Front Lower Shock absorber has an excessively worn bush both (2.7.4) | 1 |
| Nearside Rear Brake cable has restricted free movement |1.1.15 |e|| | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.A.1| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion Wheel arch |6.1.C.1| | 1 |
| Offside Rear Parking |secondary brake| on a single line braking system grabbing severely |1.3.1 |c|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength above top suspension arm (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is inadequately repaired outer sill at rear showing catalloy (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area is inadequately repaired outer sill showing catalloy (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed no fan belt alternator seized (8.2.1.2 (d)) | 1 |
| Suspension component mounting prescribed area is excessively corroded Offside Front Chassis At Anti Roll Bar Mounting |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced under floor section (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner rear wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear lower point |7.1.1 |a| |i|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner wing |6.1.A.1| | 1 |
| Battery insecure Inside the boot |1.9.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill tp wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis rail (6.1.1 (c) (ii)) | 1 |
| Front Position lamp not working BOTH (4.2.1 (a) (ii)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced body sill (7.1.1 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body sill (5.3.6 (a) (i)) | 1 |
| Front Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Offside Rear Service brake excessively binding Possible caliper seized |1.2.1 |f|| | 1 |
| Offside Rear Body component corroded and likely to cause injury inner and outer sill as marked. (6.2.1 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt BOTH |5.3.4 |b| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor various places (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under sill (7.1.1 (a) (i)) | 1 |
| Rear Tie bar/rod has excessive play in a pin/bush both |2.4.G.2| | 1 |
| Front wheel bearing rough when rotated both |2.5.A.2| | 1 |
| Offside Front Inner Subframe mounting prescribed area is excessively corroded wing |2.4.A.3| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/ undersill (6.1.1 (c) (i)) | 1 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Seat belt anchorage prescribed area is excessively corroded os |5.2.6| | 1 |
| Offside Front Anti-roll bar rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill as marked |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Anti-roll bar mounting |2.4.A.3| | 1 |
| Offside Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Central Brake lever has insufficient reserve travel Rear brake calipers adjusted to correct excess hand brake lever travel (1.1.2 (a)) | 1 |
| Nearside Rear Radius arm locating pin incorrectly positioned |2.4.G.3a| | 1 |
| Nearside Rear Radius arm locating pin locking device not properly locked |2.4.G.3b| | 1 |
| Rear Vehicle structure has an inadequate repair which adversely affects braking or steering |6.1.A.1| | 1 |
| Front Vehicle structure has an inadequate repair which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Parking brake inoperative on one side low effort (1.4.1 (a)) | 1 |
| Outer Rear Lower Exhaust system not adequately supported |7.1.1| | 1 |
| Centre Rear Lower Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rear sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced rear sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rollbar mount (5.3.6 (a) (i)) | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering roll bar mounts both sides (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering wheel arch linner (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill area does not feel firm when you press it with your finger and thumb. Within 30 cms of seatbelt mounting (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill area does not feel firm when you press it with your finger and thumb. Within 30 cms of seatbelt mounting, previously repaired (7.1.1 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting likely to become detached |5.3.3 |a| |ii|| | 1 |
| Nearside Front Anti-roll bar has excessive play in a ball joint droplink |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush droplink |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush droplink |2.4.G.2| | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced by battery tray (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure strengthening plate or fastening insecure outer and inner sill (6.1.1 (b) (i)) | 1 |
| Offside Rear Braking system leaking caliper-found on pressure test |3.6.A.1| | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch area (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel, previous weld patch has corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer chassis [recomend axle being removed for welding] (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer chassis [would recomend axle removed fof welding] (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis side and under (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis side and under (5.3.6 (a) (i)) | 1 |
| Nearside Front Brake hose excessively twisted Catching on the lower wishbone (1.1.12 (b) (ii)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both sides (5.3.6 (a) (i)) | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering outer sil (6.1.1 (c) (ii)) | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering inner sil (6.1.1 (c) (ii)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SILL (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis near lower suspension arm mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill back |7.1.1 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer and inner sill (7.1.1 (a) (i)) | 1 |
| Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both sides (6.1.1 (c) (i)) | 1 |
| Nearside Front Steering system fouling |2.2.D.2a| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Nearside Front Body insecure wing loose |6.2.2 |a| |i|| | 1 |
| Offside Front Body insecure wing loose |6.2.2 |a| |i|| | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened wishbone |2.4.G.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer and inner sill areas |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded CHASS/LEG |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded CHASS/LEG |2.4.A.3| | 1 |
| Nearside Rear Outer Subframe mounting prescribed area is excessively corroded SILL |2.4.A.3| | 1 |
| Offside Rear Outer Subframe mounting prescribed area is excessively corroded SILL |2.4.A.3| | 1 |
| Rear Parking |secondary brake| on a single line braking system has inadequate effort at a wheel |1.3.1 |a| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg corroded and holed (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg corroded and holed (6.1.1 (c) (i)) | 1 |
| Brake lever has insufficient reserve travel excessive (1.1.2 (a)) | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded and holed (6.1.1 (c) (i)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded and holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch corroded and weak (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch corroded and weak (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded and weak (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded main chassis member next to anti roll bar D bush mounting |2.4.A.3| | 1 |
| Offside Front Engine mounting excessively loose (6.1.8 (a) (ii)) | 1 |
| Nearside Front Engine mounting excessively loose (6.1.8 (a) (ii)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill and arch area |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill and arch area |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill end/arch |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill end/arch |5.2.6| | 1 |
| Steering locking device ineffective Nearside track rod end lock nut loose |2.1.3 |d|| | 1 |
| Nearside Rear Brake linkage has abnormal movement of levers indicating excessive wear or maladjustment (1.1.15 (f)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor/inner sill |7.1.1 |a| |i|| | 1 |
| Front Upper Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Centre Power steering pipe|s| or hose|s| leaking from a joint front |2.3.3b| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings at sill |6.1.B.2| | 1 |
| Central Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded (6.2.2 (d) (i)) | 1 |
| Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor on both side (6.2.2 (d) (i)) | 1 |
| Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch both sides (6.2.2 (d) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded florr/sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis anti roll bar mounting |2.4.A.3| | 1 |
| Subframe mounting prescribed area is excessively corroded BOTH REAR OUTER SILLS |2.4.A.3| | 1 |
| Hydraulic brake cylinder leaking hydraulic fluid BOTH REAR |3.6.A.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded LOWER ARM |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded LOWER ARM |2.4.A.3| | 1 |
| Road wheel more than one fixing missing x 4 |5.2.1 |a| |ii|| | 1 |
| Emissions not tested Due to water up exhaust |8.2.1.2 |d|| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wishbone |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wishbone |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings innersill |6.1.B.2| | 1 |
| Offside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings innersill |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has damage which adversely affects braking or steering floor |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 1 |
| Offside Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Nearside Lower Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Nearside Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
| Nearside Front Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Offside Front Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Nearside Suspension arm locating pin locking device missing |2.4.G.3b| | 1 |
| Offside Front Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Exhaust has a major leak of exhaust gases centre section to rear box (6.1.2 (a)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering above top suspension arm (6.1.1 (c) (ii)) | 1 |
| Emissions not tested due to major leak in exhaust system (8.2.1.2 (d)) | 1 |
| Nearside Rear Hydraulic brake calliper damaged and braking performance affected |1.1.16 |a| |ii|| | 1 |
| Front Lower Shock absorbers has an excessively worn bush both side (5.3.2 (c)) | 1 |
| Lower Suspension arm pin or bush excessively worn all around and upper (5.3.4 (a) (i)) | 1 |
| Offside Front Service brake lagging in operation and offside rear |1.2.1 |d|| | 1 |
| Rear coil spring broken both sides |2.4.C.1a| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering Outer sill |6.1.1 |c| |ii|| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering Outer sill |6.1.1 |c| |ii|| | 1 |
| Service brake is causing the vehicle to swerve to the nearside |1.2.1 |b| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor deformed/split |7.1.1 |a| |i|| | 1 |
| Offside Rear Brake pipe connection leaking on a hydraulic braking system caliper |1.1.11 |b| |ii|| | 1 |
| Front Windscreen wiper missing (3.4 (a)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Nearside Front Brake hose leaking on a hydraulic braking system flexi to caliper (1.1.12 (c) (ii)) | 1 |
| Oil leaking excessively from engine oil filter (8.4.1 (a) (i)) | 1 |
| Rear brake disc contaminated by brake fluid |3.5.1h| | 1 |
| Offside Rear rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
| Offside Rear Suspension arm inappropriately repaired repaired by welding |2.4.A.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded In front of top arm |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded In front of top arm |2.4.A.3| | 1 |
| Brake hydraulic reservoir cap missing |3.6.G.1a| | 1 |
| Offside Front Tie bar/rod rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced in 3 places |7.1.1 |a| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced engine bay |6.1.1 |c| |i|| | 1 |
| Nearside Rear Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Suspension component attachment bracket/mounting corroded and seriously weakened whish bone |5.3.3 |b| |i|| | 1 |
| Offside Rear Suspension component attachment bracket/mounting corroded and seriously weakened whish bone |5.3.3 |b| |i|| | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced seal |6.1.1 |c| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Front Anti-roll bar insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Nearside Front Inner Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired inner sill and floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced NEAR SUBFRAME AND ANTI ROLL BAR MOUNTS 2X HOLES (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced NEAR SUBFRAME AND ANTI ROLL BAR MOUNTS (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded arm |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded arm |2.4.A.3| | 1 |
| Offside Front Suspension arm damaged and seriously weakened |2.4.G.1| | 1 |
| Nearside Rear Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Central Emissions not tested |8.2.1.2 |d|| | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak |8.2.1.1 |b|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint drop link |2.4.G.2| | 1 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill |6.1.B.2| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill |6.1.B.2| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill near front jacking point |6.1.B.2| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill holed and corroded |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded floor holed and corroded |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill holed and corroded |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor pan area |5.2.6| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Offside Front Body component corroded and likely to cause injury wing holed (6.2.1 (a) (i)) | 1 |
| Brake performance not tested due to fluid leak |3.7.A.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring seat at top corroded and holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring seat corroded and holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor holed (5.3.6 (a) (i)) | 1 |
| Offside Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg section |5.3.6 |a| |i|| | 1 |
| Offside Front Floor excessively deteriorated floor (6.2.4 (a) (i)) | 1 |
| Offside Rear Shock absorber insecure |2.7.2b| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak centre joint (8.2.2.1 (b)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened w/bone (5.3.3 (b) (i)) | 1 |
| Nearside Rear Lower Suspension arm attachment bracket/mounting corroded and seriously weakened & o/s/r/l retaining washers (5.3.3 (b) (i)) | 1 |
| Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner/sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner/sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Parking brake inoperative on one side no effort (1.4.1 (a)) | 1 |
| Offside Rear Parking brake inoperative on one side little effort (1.4.1 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired whhelarch/inner sill area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheelarch/sill area (5.3.6 (a) (i)) | 1 |
| Nearside Front Coil spring worn so that its cross sectional area is reduced and seriously weakened or seated incorrectly |5.3.1 |b| |i|| | 1 |
| Offside Rear Coil spring worn so that its cross sectional area is reduced and seriously weakened |5.3.1 |b| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced TO CROSSMEMBER |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced TO CROSSMEMBER |6.1.1 |c| |i|| | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill marked yellow (6.1.1 (c) (i)) | 1 |
| Offside Front Upper Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Rear Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shocker mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened holed by corrosion (5.3.3 (b) (i)) | 1 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened holed by corrosion (5.3.3 (b) (i)) | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Suspension arm corroded and seriously weakened Lower arm |5.3.3 |b| |i|| | 1 |
| Offside Rear Suspension arm corroded and seriously weakened Lower arm |5.3.3 |b| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis |5.3.6 |a| |ii|| | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Boot floor |6.1.1 |c| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded floor to sill |2.4.A.3| | 1 |
| Steering column top mounting bracket insecure |2.1.2d| | 1 |
| Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner sill panel corroded (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner sill panel corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer sill area |5.2.6| | 1 |
| Rear Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Emissions unable to be completed coolant leak noticed, emmissions test aborted (8.2.1.2 (d)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nearside rear outer sill |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside rear outer sill |7.1.1 |a| |i|| | 1 |
| Brake pipe inadequately clipped front to rear |3.6.B.1| | 1 |
| Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is severely distorted sill |5.2.6| | 1 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Service brake excessively binding (1.2.1 (f)) | 1 |
| Floor excessively deteriorated (6.2.4 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded cill |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Offside Brake pipe leaking on a hydraulic braking system front to rear at the rear (1.1.11 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back |5.3.6 |a| |i|| | 1 |
| Front Suspension arm corroded and seriously weakened Both (5.3.3 (b) (i)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced cill (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced cill (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced cill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced cill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced cill (7.1.1 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced center cill (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced cill (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced center cill (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength behind wheel dangerous (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired behind wheel dangerous (5.3.6 (a) (i)) | 1 |
| Floor in such a condition it is likely to cause load insecurity or instability boot (6.2.4 (a) (ii)) | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both outer slls |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both inner sills |6.1.B.2| | 1 |
| Rear Braking system leaking both rear calipers |3.6.A.1| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Central Rear Exhaust has a major leak of exhaust gases exhaust flange (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected inner wheel arch (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected inner wheel arch (5.3.6 (a) (ii)) | 1 |
| Offside Front coil spring cracked |2.4.C.1a| | 1 |
| Offside Rear Vehicle structure fractured seriously affecting its strength within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Nearside Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis above top arm holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis above top arm holed (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body under side at rear (5.3.6 (a) (i)) | 1 |
| Nearside Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Offside Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Emissions not tested lamba high |7.3.A.1| | 1 |
| Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis around mounting excessively corroded. both n/s/f and o/s/f |5.3.3 |b| |i|| | 1 |
| Seat belt anchorage prescribed area is inadequately repaired inner sill rear excessively corroded. both n/s and o/s |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension arm insecure and impairing directional stability bolt loose. |5.3.3 |a| |ii|| | 1 |
| Nearside Rear Suspension arm insecure and impairing directional stability lower wish bone both securing bolts loose |5.3.3 |a| |ii|| | 1 |
| Headlamp incorrect colour both |1.7.5b| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill panels (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill panels (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis fractured |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is fractured chass leg hole with in 30cm of suspension mount |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill holed and corroded with 30cm of lower seat belt mount |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases rear exhaust flange |7.1.2| | 1 |
| Offside Rear Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Rear Anti-roll bar linkage synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill x 2 (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering of outer sill |6.1.1 |c| |ii|| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering of outer sill |6.1.1 |c| |ii|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded INNER AND OUTER SILL |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded INNER AND OUTER SILL |5.2.6| | 1 |
| Nearside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Parking brake recording little or no effort |3.7.D.3a| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded lower sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded lower sill |5.2.6| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering lower sill |6.1.A.1| | 1 |
| Position lamp not working All lamps not working (4.2.1 (a) (ii)) | 1 |
| Rear Electrical wiring likely to touch hot or rotating parts Earth cable (4.11 (a) (iii)) | 1 |
| Nearside Front Anti-roll bar has excessive play in a ball joint drop link |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a ball joint drop link |2.4.G.2| | 1 |
| Offside Front Brake pipe leaking on an air braking system (1.1.11 (b) (i)) | 1 |
| Exhaust has a major leak of exhaust gases joint at rear silencer |7.1.2| | 1 |
| Offside Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Nearside Front Sub-frame corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| brake disc in such a condition that it is seriously weakened front both |3.5.1i| | 1 |
| brake disc in such a condition that it is seriously weakened rear both |3.5.1i| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both sills front and rear holed |6.1.B.2| | 1 |
| Track rod end ball joint has excessive play nsf |2.2.B.1f| | 1 |
| front brake binding front binding |3.7.B.1| | 1 |
| Nearside Direction indicator adversely affected by the operation of another lamp |4.4.3 |b|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WING CHASSIS (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis at floor panel |6.1.B.2| | 1 |
| Offside Front Lower Subframe mounting prescribed area is excessively corroded chassis at floor panel |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill and floor panel |2.4.A.3| | 1 |
| Nearside Front Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front Suspension arm corroded and seriously weakened both sides |2.4.G.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outersill |5.2.6| | 1 |
| Offside Rear Upper Torsion bar insecure at an end fixing |2.4.E.2| | 1 |
| Inner Rear brake disc excessively scored |3.5.1h| | 1 |
| Offside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill (5.3.6 (a) (ii)) | 1 |
| Offside Front Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Brake pedal has insufficient reserve travel brake pedal spongy (1.1.2 (a)) | 1 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill at rear jacking point |6.1.B.2| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded centre floor |5.2.6| | 1 |
| Offside Front Outer Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Front Upper Suspension arm locating pin retaining device missing securing device at nut |2.4.G.3b| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill near rear jacking point |6.1.B.2| | 1 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill near rear jacking point |6.1.B.2| | 1 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill near rear jacking point |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering above anti roll bar bush |6.1.A.1| | 1 |
| Nearside Inner Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Outer Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Outer Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch |6.2.2 |d| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch |6.2.2 |d| |i|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg corroded and holed |5.3.6 |a| |i|| | 1 |
| Outer Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded floorpan |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area |5.3.6 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Front Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Brake performance not tested system leaking |3.7.A.1| | 1 |
| Nearside Front Body panel corroded and likely to cause injury sill (6.2.1 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage likely to fail (5.3.3 (b) (ii)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Quarter sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is inadequately repaired arch |5.3.6 |a| |i|| | 1 |
| Nearside Rear Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassic |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassic |5.3.6 |a| |i|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill rusted through |7.1.1 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded Rear sills near jacking point |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Rear sills near jacking point |2.4.A.3| | 1 |
| Offside Rear Brake lever has restricted free movement caliper park brake |1.1.15 |e|| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill corroded at rear of car (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill corroded at rear of car (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill corroded at rear of car (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Exhaust has a major leak of exhaust gases mid and rear exhaust joint corroded and deteriorated (6.1.2 (a)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill holed right along |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill all holed right along |6.2.2 |d| |i|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill all corroded |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill all corroded |6.2.2 |d| |i|| | 1 |
| Nearside Rear Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Parking brake inoperative on one side low effort 50kg |1.4.1 |a|| | 1 |
| Offside Parking brake inoperative on one side very low effort 10kg |1.4.1 |a|| | 1 |
| Rear Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Rear Inner Brake prescribed area is excessively corroded sill (1.1.21 (e) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arches to sills (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength quarter panel inner (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength quarter panel inner (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch & sill endcap (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch & sill endcap (5.3.6 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill. (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill. (6.1.1 (c) (i)) | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings offside sill rear section |6.1.B.2| | 1 |
| Offside Rear Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Emissions not tested rear exhaust system detatched |8.2.2.2 |e|| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill / chassis within 30cm of seat belt fixing |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill / chassis within 30cm of seat belt fixing |6.1.B.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis of |2.4.A.3| | 1 |
| Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt both |2.4.G.2| | 1 |
| Offside Front Lower Front suspension locking device missing |2.5.A.4| | 1 |
| Anti-roll bar linkage fractured Nearside front |2.4.G.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg |5.3.6 |a| |i|| | 1 |
| Nearside Front Headlamp aim beam image too far to the left |1.6.B4| | 1 |
| Emissions not tested the CO levels too high to pass |7.3.A.1| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings shocker top |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings battery tray |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings middle of inner sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch / sill |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner lower arch |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings upper inner arch |6.1.B.2| | 1 |
| Offside Ball joint has excessive play track rod end |2.2.B.1f| | 1 |
| Nearside Rear Brake cable has restricted free movement (1.1.15 (e)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded rear sill holed / corroded. |5.2.6| | 1 |
| Offside Rear Suspension arm fractured (5.3.3 (b) (ii)) | 1 |
| Brake performance unable to be tested Due to rear ferrules (1.2.1 (g)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Sill fractured at various points (6.2.2 (d) (i)) | 1 |
| Nearside Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting sill holed (6.2.2 (d) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at anti roll bar (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength a panel (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength a panel (5.3.6 (a) (i)) | 1 |
| Parking brake lever is impeded in its travel no reserve travel |3.1.6c| | 1 |
| Offside Front Power steering ram|s| leaking from a failed joint |2.3.3b| | 1 |
| Power steering pipe|s| or hose|s| excessively corroded x3 |2.3.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength [inner cill] (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength [inner cill] (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced [inner cill] (7.1.1 (a) (i)) | 1 |
| Offside Rear position lamp|s| obviously incorrectly positioned |1.1.A.3a| | 1 |
| Offside Rear Stop lamp obviously incorrectly positioned |1.2.1a| | 1 |
| Offside Rear fog lamp obviously incorrectly positioned |1.3.2a| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper suspension arm mount front area corroded and holed (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front suspension arm mount area corroded and holed (5.3.6 (a) (i)) | 1 |
| Front Anti-roll bar linkage has excessive play in a pin/bush both |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill excessively corroded |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill excessively corroded |7.1.1 |a| |i|| | 1 |
| Front Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Rear Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Front Direction indicators not working |1.4.A.2c| | 1 |
| Rear Direction indicators not working |1.4.A.2c| | 1 |
| Front Headlamp aim projected beam image is obviously incorrect Both front headlight lens misty (4.1.2 (c)) | 1 |
| Offside Rear Parking brake lever has excessive movement indicating incorrect adjustment Handbrake has no effort (1.1.6 (c)) | 1 |
| Offside Driver`s seat insecure |6.2.A.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan/outrigger (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid brake caliper (1.1.16 (b) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength side member (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting likely to become detached locking nut (5.3.3 (a) (ii)) | 1 |
| Front Headlamp levelling device inoperative both (4.1.5 (a)) | 1 |
| Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Floor excessively deteriorated boot floor. battery coming through |6.2.4 |a| |i|| | 1 |
| Power steering component leaking pipe at rack (2.1.5 (a)) | 1 |
| Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner chassis rail (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch/sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer doorsill to inner sill |6.1.B.2| | 1 |
| Electrical wiring inadequately supported under car,on strip lights |1.9.2a| | 1 |
| Seat belt anchorage prescribed area is excessively corroded sills and inner sills both sides |5.2.6| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings behind wheel |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inside wheel well |7.1.1 |a| |i|| | 1 |
| Rear front brake recording little or no effort |3.7.B.5a| | 1 |
| Brake performance not tested System leaking |3.7.A.1| | 1 |
| Offside Rear Braking system leaking Burst metal pipe |3.6.A.1| | 1 |
| Steering box leaking to the extent that oil is dripping (2.1.1 (e) (ii)) | 1 |
| Offside Outer Rear Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis near anti roll mount |6.1.1 |c| |i|| | 1 |
| Offside Rear Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear upper floor (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie leg at inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie leg at inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Brake pipe leaking |3.6.A.1| | 1 |
| Offside Front Body component corroded and likely to cause injury wing (6.2.1 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor at sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under sill (6.1.1 (c) (i)) | 1 |
| Brake pipe leaking on a hydraulic braking system front to rear metal brake pipe burst during brake test. (1.1.11 (b) (ii)) | 1 |
| Undertray likely to become detached engine (6.2.1 (a) (ii)) | 1 |
| Rear Exhaust system insecure box broken (6.1.2 (a)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing at chassis (6.1.1 (c) (i)) | 1 |
| Offside Brake cable insecure handbrake (1.1.15 (c)) | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn drop link (5.3.4 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor at wheel arch (6.1.1 (c) (i)) | 1 |
| Bonnet primary retaining device insecure missing (3.1 (c)) | 1 |
| Brake performance unable to be tested pipe broke (1.2.1 (g)) | 1 |
| Offside Brake cable insecure (1.1.15 (c)) | 1 |
| Drive belt excessively worn alternator |6.1.7 |c| |i|| | 1 |
| Brake disc significantly and obviously worn all (1.1.14 (a) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced both inner and outer sills (6.1.1 (c) (i)) | 1 |
| Front Steering box leaking to the extent that oil is dripping (2.1.1 (e) (ii)) | 1 |
| Steering system excessively tight |2.2.D.1| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill / floor |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis corroded |6.1.A.1| | 1 |
| Offside Vehicle structure has a modification which adversely affects braking or steering outer floor at rear |6.1.A.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases joint corroded |7.1.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer floor to sill |6.1.B.2| | 1 |
| Emissions not tested rear exhaust blow |8.2.1.2 |d|| | 1 |
| Brake hydraulic reservoir cap missing |1.1.10 |e|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor |5.3.6 |a| |i|| | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength boot floor / inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner / outer sill area. |5.2.6| | 1 |
| Central Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced offside chassis |6.1.1 |c| |i|| | 1 |
| Nearside Front Lower Body panel corroded and likely to cause injury wing |6.2.1 |a| |i|| | 1 |
| Offside Front Lower Body panel corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Offside Front Steering linkage ball joint has excessive play |2.1.3 |b| |i|| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill corroded |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill corroded |6.1.B.2| | 1 |
| Nearside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings within front coil spring mount |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings at wheel arch |marked with yellow chalk| |6.1.B.2| | 1 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg holed x2 |marked with yellow chalk| |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill / floor |5.2.6| | 1 |
| Offside Rear Suspension arm cracked Anti-roll bar linkage mounting torn out |2.4.G.1| | 1 |
| Nearside Rear Sub-frame inappropriately repaired Brace bar held on with a jubilee clip and a cable tie |2.4.A.2| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Brake hose inappropriately repaired |3.6.A.3| | 1 |
| Nearside Rear Anti-roll bar linkage corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Brake pipe at imminent risk of failure or fracture Front to rear section. (by Clip). (1.1.11 (a)) | 1 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached is detached |5.3.4 |a| |ii|| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill / Floor (7.1.1 (a) (i)) | 1 |
| Service brake excessively fluctuating Both front (1.2.1 (e)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced back of sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced back of sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis under vehicle (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis under front wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis under front wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner flitch |5.3.6 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Position lamp with a multiple light source more than 1/2 not functioning flickering (4.2.1 (a) (ii)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner flitch (6.1.1 (c) (i)) | 1 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive exhaust blow |7.3.D.3| | 1 |
| Rear Seat belt anchorage prescribed area is excessively corroded both inner sills |5.2.6| | 1 |
| Central Exhaust system not adequately supported |7.1.1| | 1 |
| Emissions not tested co and lamba to high |7.3.A.1| | 1 |
| Brake pipe inadequately clipped ALONG OFFSIDE |3.6.B.1| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint metal link |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint metal link |2.4.G.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases back box |7.1.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner/outer sill |5.2.6| | 1 |
| Offside Rear Anti-roll bar ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer (6.1.1 (c) (i)) | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering o/s/r outer sill |6.1.A.1| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering o/s/r inner sill |6.1.A.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner and outer |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer |2.4.A.3| | 1 |
| Offside Rear Stop lamp(s) showing white light to the rear (4.3.3 (a) (ii)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis to floor (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis to floor (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Front position lamp|s| not working SIDE LIGHT |1.1.A.3b| | 1 |
| Offside Rear Brake damaged to the extent that the braking system is adversely affected BRAKE CALIPER LEAKING |1.1.21 |a| |i|| | 1 |
| Nearside Front Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 1 |
| Nearside Passenger`s seat insecure |6.2.A.1| | 1 |
| Nearside Front Upper Front suspension has a suspension upper ball joint securing nut not locked split pin/clip missing |2.5.B.1a| | 1 |
| Nearside Front Anti-roll bar linkage insecure UNABLE TO CHECK FOR PLAY |2.4.G.1| | 1 |
| Offside Rear brake caliper has restricted free movement parking brake mechanism of |3.5.1k| | 1 |
| Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected BOTH SIDES FRONT CHASSIS CLOSE TO ANTIROLL BAR MOUNTS |5.3.6 |a| |ii|| | 1 |
| Anti-roll bar linkage worn and seriously weakened all 4 |2.4.G.1| | 1 |
| Nearside Lower Front suspension retaining device missing |2.5.A.4| | 1 |
| Nearside Integral body structure has excessive corrosion which adversely affects braking or steering Inner sill (6.1.1 (c) (ii)) | 1 |
| Offside Integral body structure has excessive corrosion which adversely affects braking or steering Inner sill (6.1.1 (c) (ii)) | 1 |
| Nearside Integral body structure has excessive corrosion which adversely affects braking or steering Outer sill (6.1.1 (c) (ii)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor pan (6.1.1 (c) (i)) | 1 |
| Offside Rear Anti-roll bar has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Offside Power steering ram|s| leaking from a failed component |2.3.3b| | 1 |
| Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` air freshener |8.3.1e| | 1 |
| Nearside Rear Vehicle structure has an inadequate repair which adversely affects braking or steering previous sill repair not to acceptable standards |6.1.A.1| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering previous sill repair not to acceptable standards |6.1.A.1| | 1 |
| Brake performance not tested brake test not carried out due to corrosion inadequate repairs and broken springs. |3.7.A.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor and outer sill holed |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor and outer sill holed |5.2.6| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded inner wing holed at strut top |2.4.A.3| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded inner wing at strut top holed |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing at anti roll bar mounting point |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing at anti roll bar mounting point |2.4.A.3| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings osr inner sill |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings os front floor |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings nsr inner sill |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings nsf chassis leg split as suspension arm |6.1.B.2| | 1 |
| Offside Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
| Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength boot floor and inner arch (5.3.6 (a) (i)) | 1 |
| Emissions not tested unable to get reading from rear (8.2.1.2 (d)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis/floor |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired inner sill/floor |2.4.A.3| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL |6.1.B.2| | 1 |
| Front Suspension arm attachment bracket/mounting insecure and impairing directional stability upper and lower arms (5.3.3 (a) (ii)) | 1 |
| Rear Suspension arm attachment bracket/mounting insecure and impairing directional stability upper and lower arms (5.3.3 (a) (ii)) | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sil corroded front and rear (6.2.2 (d) (i)) | 1 |
| Rear Anti-roll bar has excessive play in a pin/bush both sides |2.4.G.2| | 1 |
| Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 1 |
| Braking system leaking union @ rear flex hose |3.6.A.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wing area |7.1.1 |a| |i|| | 1 |
| Offside Front Body panel corroded and likely to cause injury wing |6.2.1 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing area |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area |5.3.6 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases centre / rear flange gasket |7.1.2| | 1 |
| Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill X2 |6.1.B.2| | 1 |
| Offside Front Vehicle structure has a fracture which is likely to adversely affect braking or steering (6.1.1 (a) (ii)) | 1 |
| Offside Front Inner Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Front Outer Body component damaged and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Floor in such a condition it is likely to cause load insecurity or instability Nearside and offside. Boot floor (6.2.4 (a) (ii)) | 1 |
| Body panel corroded and likely to cause injury Near sill. And outersill (6.2.1 (a) (i)) | 1 |
| Offside Rear Exhaust emissions likely to be affected by an exhaust leak Exhaust corrodes (8.2.2.1 (b)) | 1 |
| Offside Front Suspension arm damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting N/s & o/s. Front and rear (6.2.2 (d) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded front and rear |5.2.6| | 1 |
| Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings front chassis both sides |6.1.B.2| | 1 |
| Steering retaining device missing split pins on both track rod ends missing |2.2.C.1g| | 1 |
| Offside Front Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Anti-roll bar linkage missing |2.4.G.1| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner and outer cill |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill holed |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sills |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired outer sill not seam welded (5.3.6 (a) (i)) | 1 |
| Brake performance unable to be tested due to hydraulic clutch fault (1.2.1 (g)) | 1 |
| Nearside Rear Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced Sill Area (6.1.1 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill section (5.3.6 (a) (i)) | 1 |
| Exhaust emits dense blue smoke at idle |7.3.A.2b| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded sil |5.2.6| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength sill |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength sill |5.2.6| | 1 |
| Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Service brake indicates brake bind |3.7.D.2a| | 1 |
| Offside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced Sill (6.1.1 (d) (i)) | 1 |
| Nearside Rear Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced Sill (6.1.1 (d) (i)) | 1 |
| Offside Front Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced Sill (6.1.1 (d) (i)) | 1 |
| Offside Front Upper coil spring fractured |2.4.C.1a| | 1 |
| Exhaust has a major leak of exhaust gases on centre join |7.1.2| | 1 |
| Nearside Exhaust has a major leak of exhaust gases back box around weld |7.1.2| | 1 |
| Nearside Rear Anti-roll bar severely distorted Anti Roll Bar Touching Coil Spring. |2.4.G.1| | 1 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement D Bush. |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement D Bush. |2.4.G.2| | 1 |
| Brake pedal fouling on other parts of the vehicle |3.3.A.4| | 1 |
| Offside Rear Road wheel distorted |4.2.A.1a| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis by anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis by anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area fractured significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Brake performance not tested due to condition of brakes |3.7.A.1| | 1 |
| Offside brake caliper has restricted free movement |3.5.1k| | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail on floor underside (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail on floor underside (6.1.1 (c) (i)) | 1 |
| Body component corroded and likely to cause injury nearside rear arch due to corrosion (6.2.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure is deformed and structural rigidity is significantly reduced |6.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected subframe mount (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Windscreen damaged and affecting the driver`s view of the road |3.2 |a| |ii|| | 1 |
| Nearside Rear Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 1 |
| Offside Rear Upper Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Coil spring fractured or broken |5.3.1 |b| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced corrosion within 30cm of a subframe mounting (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Electrical wiring likely to touch hot or rotating parts second lambda sensor rubbing on prop shaft (4.11 (a) (iii)) | 1 |
| Offside Rear Vehicle structure strengthening plate or fastening insecure bolt has yellow crayon on (6.1.1 (b) (i)) | 1 |
| Exhaust has a major leak of exhaust gases mid section to back box join (6.1.2 (a)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor (6.1.1 (c) (i)) | 1 |
| Front position lamp|s| not working front both side lamps |1.1.A.3b| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings near front jacking point |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner and outer body sill to flooring |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak centre/rear (8.2.1.1 (b)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced drivers floor as seatbelt is attached to drivers seat (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer |7.1.1 |a| |i|| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill at rear jacking point |6.1.B.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ARM HOLED |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced INNER WHEEL ARCH (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced INNER WHEEL ARCH (7.1.1 (a) (i)) | 1 |
| Headlamp not working on main beam Both (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor at jacking point holed |6.1.B.2| | 1 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Front Passenger`s seat insecure |6.2.A.1| | 1 |
| Anti-roll bar linkage has excessive play in a pin/bush link broken |2.4.G.2| | 1 |
| Nearside Front Lower Power steering pipe/hose leaking from back of engine (2.1.5 (a)) | 1 |
| Nearside Rear Electrical wiring damaged and bare wires exposed |1.9.2c| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floorpan holed within 30cm of seat mount |6.1.B.2| | 1 |
| Offside Rear Brake valve leaking |3.6.A.1| | 1 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill holed with corrosion |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill holed with corrosion |7.1.1 |a| |i|| | 1 |
| Bootlid cannot be secured in the closed position |6.4.1| | 1 |
| coil spring incomplete |2.4.C.1a| | 1 |
| Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Nearside Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Central Rear Lower Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mt |2.4.A.3| | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Rear Lower Suspension arm inappropriately repaired plate been welded on to cover hole |2.4.A.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing and chassis leg holed with corrosion |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing and chassis leg holed with corrosion at anti roll bar mounting point |2.4.A.3| | 1 |
| Emissions not tested due to major exhaust leak |7.3.A.1| | 1 |
| Offside Ball joint has excessive play TRE |2.2.B.1f| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Rear Braking system leaking at junction |3.6.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill holed and corroed |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension component insecurely attached bolt missing |5.3.3 |a| |i|| | 1 |
| Offside Rear Integral body structure is deformed and structural rigidity is significantly reduced chassis rail (6.1.1 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis badley holed and corroed |2.4.A.3| | 1 |
| Offside Front Anti-lock braking system wiring excessively damaged insecure |3.4.3| | 1 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
| coil spring broken Both front |2.4.C.1a| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded siil |5.2.6| | 1 |
| Electrical wiring insecure lambda wire |1.9.2a| | 1 |
| Battery insecure battery box corroded |1.9.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded wheel arch under bonnet corroded around spring mounting |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg corroded visiable from under the bonnet in a prescibed area |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch is corroded within a prescibed area |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch is corroded with in a prescribed area |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner cill is corroded |5.2.6| | 1 |
| Battery insecure clamps missing and mount/floor corroded |1.9.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill/floor |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill/floor |5.2.6| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded front chassis leg @ a/r bar mount |2.4.A.3| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill holed and corroded |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded sill holed and corroded |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded front of inner wing |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded rear of inner wing |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded lower wing |2.4.A.3| | 1 |
| Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Nearside Front Upper Front suspension locking device missing ball joint |2.5.A.4| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WHEEL ARCH |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL END CAP |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill as marked |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill as marked |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner arch as marked |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner arch as marked |7.1.1 |a| |i|| | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch/chassis (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch/chassis (5.3.6 (a) (i)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting middle floor holed and corroded (6.2.2 (d) (i)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting front and middle fooor holed and corroded (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill and sill closing panel |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired inner sill and sill closing panel, previous patch not attatched most of the way around |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill closing panel |5.2.6| | 1 |
| Stop lamp has a product on the lens so it is not visible from a reasonable distance |1.2.1d| | 1 |
| Offside Rear Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Tie bar/rod rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering in engine bay (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering osf in engine bay (6.1.1 (c) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area fractured significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area fractured significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Suspension arm corroded and seriously weakened both rear lower (5.3.3 (b) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both rear inner arches (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength At battery (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis below front floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength closing panel |5.3.6 |a| |i|| | 1 |
| Offside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Rear Drive shaft uj which forms part of the suspension has a missing flange bolt |2.4.G.4c| | 1 |
| Rear Drive shaft uj which forms part of the suspension has a loose flange bolt |2.4.G.4c| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded under sill , 2 places |5.2.6| | 1 |
| Offside Rear Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Brake pipe leaking |3.6.A.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front leg and strut area (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill soft (5.3.6 (a) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side binding (1.4.1 (a)) | 1 |
| Nearside Front Integral body structure has excessive corrosion which adversely affects braking or steering chassi leg (6.1.1 (c) (ii)) | 1 |
| Offside Front Integral body structure has excessive corrosion which adversely affects braking or steering chassi leg (6.1.1 (c) (ii)) | 1 |
| Offside Rear Integral body structure has excessive corrosion which adversely affects braking or steering inner/out sill (6.1.1 (c) (ii)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor/outrigger (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outrigger (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer/inner sill (6.1.1 (c) (i)) | 1 |
| Brake performance unable to be tested due to n/s rear lower arm (1.2.1 (g)) | 1 |
| Nearside Parking (secondary brake) on a single line braking system grabbing severely (1.3.1 (c)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Nearside Rear Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill holed |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill holed |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill holed |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill holed |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Strut Tower Holed (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Holed At Front Seat Mounting (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch (6.2.2 (d) (i)) | 1 |
| Front Inner Brake disc significantly and obviously worn both discs inner face |1.1.14 |a| |i|| | 1 |
| Offside Front Electrical wiring insecure and connectors likely to become disconnected hanging in front of peddles |4.11 |a| |ii|| | 1 |
| Engine MIL inoperative or indicates a malfunction light on dash |8.2.1.2 |h|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded close to front suspension mouting |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded close to suspension mouting |2.4.A.3| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Nearside inner rear of sill (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Offside inner rear of sill (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Nearside rear inner wheel arch (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Offside rear inner wheel arch (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Offside front inner end of sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outersill |5.3.6 |a| |i|| | 1 |
| Front Position lamp not working x2 |4.2.1 |a|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded chassis/inner wing area |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded chassis/inner wing area |2.4.A.3| | 1 |
| Anti-roll bar attachment bracket inappropriately repaired |2.4.A.2| | 1 |
| Offside Rear Upper Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Offside Rear Lower Suspension arm cracked |2.4.G.1| | 1 |
| Offside Rear Anti-roll bar cracked |2.4.G.1| | 1 |
| Nearside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Seat belt stitching badly frayed |5.2.2b| | 1 |
| Offside Rear Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Offside Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Offside Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Nearside Rear brake caliper securing device excessively deteriorated |3.5.1j| | 1 |
| Front Power steering pipe/hose excessively corroded ??2 pipes |2.1.5 |g| |i|| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
| Offside Rear Body panel corroded and likely to cause injury wheel arch corroded and holed also has sharp edges (6.2.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected at inner sill (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner chassis leg holed (5.3.6 (a) (i)) | 1 |
| Offside Front Power steering ram leaking (2.1.5 (a)) | 1 |
| Front Brake hose excessively twisted nearside and offside |1.1.12 |b| |ii|| | 1 |
| Offside Front Anti-roll bar missing (5.3.3 (a) (ii)) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint likely to become detached Has become detached (5.3.4 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 30cm anti rollbar mount |5.3.6 |a| |i|| | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Nearside Rear Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Steering locking device missing |2.2.C.1g| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded upper anchorage |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded upper anchorage |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded lower anchorage |5.2.6| | 1 |
| Offside Rear Inner Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Front Seat belt anchorage prescribed area is excessively corroded both |5.2.6| | 1 |
| Offside Front Steering arm deformed to the extent that steering is affected Rack end |2.1.3 |c| |ii|| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis to inner wing (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis to inner wing (6.1.1 (c) (i)) | 1 |
| Power steering pipe|s| or hose|s| leaking pipes to cooler |2.3.3b| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced BATTERY TRAY (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Both sides |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Both sides |6.1.B.2| | 1 |
| Offside Rear Anti-roll bar linkage synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Suspension arm damaged and seriously weakened |2.4.G.1| | 1 |
| Rear Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength frame rail (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength frame rail (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases tail pipe missing (6.1.2 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to floor |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to floor |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch at front ch leg |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch at front ch leg |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch at top turret |5.3.6 |a| |i|| | 1 |
| Nearside Rear Braking system leaking brake pipe |3.6.A.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded under side/outer sill area as marked. |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired under car/outer sill area as marked. |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired under car sill area as marked. |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded near rear exhaust system |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced rust hole in floor pan within 30cm of seatbelt anchorage (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rust hole in floor pan within 30cm seatbelt anchorage (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rust hole within 30cm of suspension top mount (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak manifold area to downpipe (8.2.1.1 (b)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded = outer sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired Floor edge (7.1.1 (a) (i)) | 1 |
| Fuel cap/sealing device ineffective fuel filler flap not opening |6.1.3 |b| |i|| | 1 |
| Offside Front Drivers airbag missing (7.1.5 (a)) | 1 |
| Power steering pipe|s| or hose|s| leaking from pump to rack |2.3.3b| | 1 |
| Power steering pipe|s| or hose|s| excessively corroded from pump to rack |2.3.2| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill at rear (7.1.1 (a) (i)) | 1 |
| Offside Rear Valve stem seriously damaged badly perished (5.2.3 (j)) | 1 |
| Brake pipe leaking on a hydraulic braking system central to rear (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill section (7.1.1 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak rear silencer holed (8.2.2.1 (b)) | 1 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn both (5.3.4 (a) (i)) | 1 |
| Offside Brake pipe leaking on a hydraulic braking system Front - Rear (1.1.11 (b) (ii)) | 1 |
| Brake pipe leaking on a hydraulic braking system front to rear brake pipe burst (1.1.11 (b) (ii)) | 1 |
| Brake performance unable to be tested brake pipe leaking/burst (1.2.1 (g)) | 1 |
| Offside Front Direction indicator has less than 50% of the light sources illuminating |1.4.A.2c| | 1 |
| Central Front Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Nearside Front Undertray likely to become detached |6.2.1 |a| |ii|| | 1 |
| Offside Front Upper Suspension arm ball joint likely to become detached locking device missing (5.3.4 (a) (ii)) | 1 |
| Offside Front Anti-roll bar linkage fractured Drop link disconnected |2.4.G.1| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both outer body sills holed |6.1.B.2| | 1 |
| Windscreen wiper blade missing |8.2.2| | 1 |
| Offside Front Lower Suspension arm locating pin locking device missing |2.4.G.3b| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded and o/s/r outer sills holed |2.4.A.3| | 1 |
| Offside Rear Anti-roll bar insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded under floor |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded under floor |2.4.A.3| | 1 |
| Offside Front Hydraulic brake calliper inadequately mounted bolt missing (1.1.16 (c) (i)) | 1 |
| Offside Rear Stop lamp(s) lens defective such that the emitted light is adversely affected (4.3.1 (b) (ii)) | 1 |
| Offside Front Position lamp not working Sidelight (4.2.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail corroded and holed adjacent to anti roll bar mount and upper suspension arm mount |2.4.A.3| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill. (7.1.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outrigger (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/wing corroded (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor chassis (5.3.6 (a) (i)) | 1 |
| Stop lamp(s) not working centre (4.3.1 (a) (ii)) | 1 |
| Nearside Front Body mounting fixings missing (6.2.2 (c) (i)) | 1 |
| Offside Front Body mounting fixings missing (6.2.2 (c) (i)) | 1 |
| Rear Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition exhaust missing (8.1.1 (a)) | 1 |
| Nearside Front Wheel bearing play so excessive it is likely to break up (5.1.3 (a) (ii)) | 1 |
| Offside Outer Front Steering locking device missing |2.2.C.1g| | 1 |
| Offside Front Service brake excessively binding seized (1.2.1 (f)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chacssis (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Silencer |7.1.2| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength n/s/f chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor at inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded main chassis in 2 places |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded main chassis in 2 places |2.4.A.3| | 1 |
| Offside Front Inner Suspension spring mounting prescribed area is excessively corroded wing |2.4.A.3| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt x2 |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt x2 |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded rear outer sill corroded and holed |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded rear outer sill corroded and holed |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg next to anti roll bar |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg next to anti roll bar |2.4.A.3| | 1 |
| Offside rear brake grabbing severely |3.7.A.5b| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner and outer sill area (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion inner and outer sills (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion inner and outer sills (7.1.1 (a) (i)) | 1 |
| Offside Front wheel bearing rough when rotated not tested |2.5.A.2| | 1 |
| Offside front parking brake recording little or no effort |3.7.B.6a| | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting |6.2.2 |d| |i|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis on outer and lower face |2.4.A.3| | 1 |
| Offside Front Rear fog lamp missing |1.3.2a| | 1 |
| Offside Rear Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Parking brake inoperative on one side not working (1.4.1 (a)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill corroded (6.1.1 (c) (i)) | 1 |
| Hydraulic fluid leaking continuously posing a serious risk to road safety power steering |8.4.1 |a| |ii|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill
|5.2.6| | 1 |
| Nearside Rear Hydraulic fluid leaking excessively caliper (8.4.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill / floor area (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill / lower wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail inner wing side (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced back of outer sill area (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Headlamp not working on main beam both (4.1.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases cat to centre pipe joint (6.1.2 (a)) | 1 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` sat nav |8.3.1b| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened at inner wing marked yellow |5.3.3 |b| |i|| | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded into a whole (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded into a whole (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |x2 places| |5.3.6 |a| |i|| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded sill area behind wing mount |2.4.A.3| | 1 |
| Nearside Rear Body panel damaged and likely to cause injury Arch in front of rear wheel |6.2.1 |a| |i|| | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Boot floor , battery tray (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Headlamp aim does not move downwards when dipped |British American headlamp| |1.8.C.4| | 1 |
| Central Rear Exhaust has a major leak of exhaust gases joint |7.1.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch at shock mount |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded ***inner sill/corner*** |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Top wishbone mounting area |2.4.A.3| | 1 |
| Nearside Rear Mechanical brake component locking device missing |3.5.1l| | 1 |
| Offside Rear Mechanical brake component locking device missing |3.5.1l| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill considerably corroded within 30cm of seatbelt mounting point. (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nearside outer sill rear (7.1.1 (a) (i)) | 1 |
| Offside Body component damaged and likely to cause injury wing mirror cover damaged |6.2.1 |a| |i|| | 1 |
| Front Track rod end ball joint has excessive play both (2.1.3 (b) (i)) | 1 |
| Rear Service brake excessively binding both (1.2.1 (f)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor/Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Wheel arch corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Battery insecure and likely to fall from carrier battery floor seating panel corroded (4.13 (a) (ii)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill marked (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis marked (6.2.2 (d) (i)) | 1 |
| Nearside Front Bumper damaged and likely to cause injury when grazed or contacted number plate bracket/not flush to body panel (6.1.4 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis / inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis / inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Rear Shock absorbers has a serious fluid leak 2x rears shockers (5.3.2 (b)) | 1 |
| Rear Exhaust has a major leak of exhaust gases flange |7.1.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill back |5.2.6| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis arm (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis arm, inner and outer (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill, inner and outer (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill, outer (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner and outer (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Body has a sharp edge caused by damage reflector on side of bumper damaged |6.1.C.1| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor |6.2.2 |d| |i|| | 1 |
| Offside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement antiroll bar link not attached |2.4.G.2| | 1 |
| Nearside Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Electrical wiring insecure Centre to rear loom |1.9.2a| | 1 |
| Steering wheel retaining device insecure loose |2.1.6| | 1 |
| Nearside Rear reflector not red in colour |1.5.1d| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sills |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sills |6.1.B.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases join |7.1.2| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Outer Integral body structure has excessive corrosion which adversely affects braking or steering Sill |6.1.1 |c| |ii|| | 1 |
| Offside Front Lower Shock absorbers insecurely attached (5.3.2 (a) (i)) | 1 |
| Front Lower Suspension arm mounting has an unsafe modification both sides . (5.3.3 (c) (i)) | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer cill |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer cill |6.1.B.2| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis in engine bay |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis in engine bay |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis in wheelarch |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis in wheelarch |2.4.A.3| | 1 |
| Nearside Front Outer Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Front Outer Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases Centre to rear joint |7.1.2| | 1 |
| Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Arch/sill (6.2.2 (d) (i)) | 1 |
| Offside Body has a sharp edge caused by corrosion Outer sill |6.1.C.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner/outer seal |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner /outer seal |7.1.1 |a| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced seal |6.1.1 |c| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced seal |6.1.1 |c| |i|| | 1 |
| Rear Exhaust has a major leak of exhaust gases back box |6.1.2 |a|| | 1 |
| Nearside Rear Brake lining(s) missing (1.1.13 (c)) | 1 |
| Brake performance not tested due to nsr outer pad broken (1.2.1 (g)) | 1 |
| Offside Front Outer Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Outer Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Rear Braking system leaking brake calliper leaking |3.6.A.1| | 1 |
| Engine MIL inoperative or indicates a malfunction P1499- EGR stepper motor 4 open circuit (8.2.1.2 (h)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner wing chassis area. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill area. (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill area. (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed Cant get pipe up broken exhaust (8.2.1.2 (d)) | 1 |
| Exhaust has a major leak of exhaust gases centre to rear sealing flange |7.1.2| | 1 |
| Nearside Rear All position lamps not working |4.2.1 |a|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner chassis above anti roll bar (5.3.6 (a) (i)) | 1 |
| Nearside Rear Upper Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed |6.2.2 |d| |i|| | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt Clip missing (2.1.3 (g) (ii)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings central chassis frame corroded/cracked |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings central chassis frame corroded/cracked |6.1.B.2| | 1 |
| Suspension component mounting prescribed area is excessively corroded Both fronts load bearing areas corroded |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg in front of upper suspension mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in front of upper suspension mounting |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill end |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner and outer sill area |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases centre flange (6.1.2 (a)) | 1 |
| Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt both (5.3.4 (b) (ii)) | 1 |
| Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt both (5.3.4 (b) (ii)) | 1 |
| Offside Front Braking system leaking Calliper piston seal |3.6.A.1| | 1 |
| Nearside Rear Stop lamp not working and lens broken |1.2.1b| | 1 |
| Offside Front Upper Steering locking device missing BALL JOINT (2.1.3 (d)) | 1 |
| Nearside Rear Lower Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength above roll bar bracket (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength above roll bar bracket (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid brake caliper |3.6.A.1| | 1 |
| Nearside Front Indicator switch faulty |1.4.A.1| | 1 |
| Offside Front Indicator switch faulty |1.4.A.1| | 1 |
| Nearside Rear Indicator switch faulty |1.4.A.1| | 1 |
| Offside Rear Indicator switch faulty |1.4.A.1| | 1 |
| Rear Coil spring fractured or broken O/S & N/S REAR COIL SPRINGS SNAPPED (5.3.1 (b) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL (6.1.1 (c) (i)) | 1 |
| Power steering ram leaking (2.1.5 (a)) | 1 |
| Rear Service brake excessively fluctuating nearside and offside (1.2.1 (e)) | 1 |
| Offside Rear Service brake excessively binding wheel bearing cannot be checked (1.2.1 (f)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill. |5.3.6 |a| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Behind road wheel (6.1.1 (c) (i)) | 1 |
| Suspension component mounting prescribed area is excessively corroded at offside sill and rear inner arch |2.4.A.3| | 1 |
| Front Exhaust has a part missing |7.1.1a| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion sill |6.1.C.1| | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front chassis legs near roll bar mounting corroded (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner (7.1.1 (a) (i)) | 1 |
| Rear Sub-frame likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner bay (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension arm cracked |2.4.G.1| | 1 |
| Nearside Front Inner Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Brake pipe connection leaking on a hydraulic braking system at block |1.1.11 |b| |ii|| | 1 |
| Brake performance not tested due to leaking pipe |1.2.1 |g|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced @sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Brake insecure pins in carrier loose |1.1.21 |c|| | 1 |
| Nearside Front Front position lamp|s| has a product on the lens so it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/foor (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill /sill lip (7.1.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis pescribed area (5.3.3 (b) (i)) | 1 |
| Offside Rear Upper Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Offside Front Brake performance not tested (1.2.1 (g)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired chassis railed corroded (6.2.2 (d) (ii)) | 1 |
| Offside Front Integral body structure is deformed and structural rigidity is significantly reduced floor pan damaged and holed (6.1.1 (a) (i)) | 1 |
| Front Braking system leaking |3.6.A.1| | 1 |
| Offside Rear Suspension arm pin or bush excessively worn lower rear (5.3.4 (a) (i)) | 1 |
| Offside Rear Sub-frame attachment bracket/mounting insecure and impairing directional stability bolt loose (5.3.3 (a) (ii)) | 1 |
| Offside Headlamp has a product on the light source which changes emitted colour to other than white or yellow (4.1.4 (b)) | 1 |
| Emissions unable to be completed due to holed exhaust (8.2.2.2 (e)) | 1 |
| Windscreen in an unacceptable condition (3.2 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor holed (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired Chassis not welded continuously (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired Chassis not continuously welded (5.3.6 (a) (i)) | 1 |
| Nearside Outer Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded rear outer sill |5.2.6| | 1 |
| Offside Rear Brake valve leaking (1.1.7 (d) (i)) | 1 |
| Nearside Rear Brake pipe excessively damaged (1.1.11 (c)) | 1 |
| Offside Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded box section |2.4.A.3| | 1 |
| Nearside Rear Brake hose bulging under pressure |1.1.12 |d|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting insecure (5.3.3 (a) (i)) | 1 |
| Sub-frame attachment bracket/mounting insecure Differential to subframe bolts (5.3.3 (a) (i)) | 1 |
| Emissions not tested due to engine idle |7.3.A.1| | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s and n/s rear outer sills (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing (6.2.2 (d) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength antiroll bar mounting (chassis) (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength antiroll bar mounting (chassis) (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded under |5.2.6| | 1 |
| Offside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |BALL JOINT| |2.2.C.1c| | 1 |
| Nearside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |BALL JOINT| |2.2.C.1c| | 1 |
| Nearside Front Upper Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |ARM| |2.2.C.1c| | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength by suspension mount (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Lower body sill at rear |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Lower body sill at rear |5.2.6| | 1 |
| Nearside Front Direction indicator incorrect colour white |1.4.A.2f| | 1 |
| Offside Front Direction indicator incorrect colour white |1.4.A.2f| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced o/s/r outer sill excessively corroded |7.1.1 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases center box broken |7.1.2| | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view glass missing |8.1.2a| | 1 |
| Offside Front Position lamp not working s/light (4.2.1 (a) (ii)) | 1 |
| Nearside Front Position lamp not working s/light (4.2.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg bottom and inner side (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor pan holed (6.1.1 (c) (i)) | 1 |
| Nearside Steering system lock to lock check twists a brake hose |2.2.D.2b| | 1 |
| Nearside Rear Hydraulic fluid leaking excessively (8.4.1 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Under side of chassis leg |5.3.6 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Under side of chassis leg |5.3.6 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases front pipe to manifold-nut missing (6.1.2 (a)) | 1 |
| Nearside Seat belt buckle not functioning as intended not release under pressure (7.1.2 (d)) | 1 |
| Offside Seat belt buckle not functioning as intended not release under pressure (7.1.2 (d)) | 1 |
| Nearside Rear Service brake indicates brake bind |3.7.D.2a| | 1 |
| Front Body has a sharp edge caused by damage number plate bracket |6.1.C.1| | 1 |
| Drivers view of the road through the swept area of the windscreen materially affected by an obstruction Sticker (3.1 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting missing (5.3.3 (a) (ii)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting missing (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting missing (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Coil spring mounting insecure (5.3.1 (a) (i)) | 1 |
| Offside Rear Coil spring mounting insecure (5.3.1 (a) (i)) | 1 |
| Offside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt boot split open |2.4.G.2| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Inner chassis rail painted white |6.1.1 |c| |ii|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Inner chassis rail painted white |6.1.1 |c| |ii|| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Inner wheel arch painted white |6.1.1 |c| |ii|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Inner wheel arch painted white |6.1.1 |c| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner chassis rail under bonnet (5.3.6 (a) (ii)) | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak holed on joint (8.2.1.1 (b)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Hole in outer sill |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch |5.3.6 |a| |i|| | 1 |
| Central Front Emission control equipment obviously defective (8.2.2.1 (a)) | 1 |
| Offside Rear Hydraulic brake calliper leaking possible leak/moist |1.1.16 |b| |i|| | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed |6.2.2 |d| |i|| | 1 |
| Nearside Rear Inner Integral body structure has excessive corrosion which adversely affects braking or steering sill small hole |6.1.1 |c| |ii|| | 1 |
| Power steering pipe/hose leaking cooler behind rad (2.1.5 (a)) | 1 |
| Headlamp light source and lamp not compatible both (4.1.4 (c)) | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Front Lower Suspension arm attachment bracket/mounting corroded and seriously weakened Shock absorber mountiong |5.3.3 |b| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch corroded |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch corroded |7.1.1 |a| |i|| | 1 |
| Offside Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt boot insecure (2.1.3 (g) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Exhaust flange leaking |7.1.2| | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting likely to become detached rubber bush (5.3.3 (a) (ii)) | 1 |
| Offside Rear Sub-frame attachment bracket/mounting likely to become detached rubber bush (5.3.3 (a) (ii)) | 1 |
| Rear Inner Brake disc in such a condition that it is seriously weakened (1.1.14 (a) (ii)) | 1 |
| Nearside Rear Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Lower Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail corroded excessively within 30cm of suspension (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail corroded excessively within 30cm of suspension (6.1.1 (c) (i)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis both sides and sills (6.1.1 (c) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Front fog lamp with a multiple light source more than 1/2 not functioning (4.5.1 (a) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is severely distorted outer sill |2.4.A.3| | 1 |
| Nearside Rear Braking system leaking Brake caliper |3.6.A.1| | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits Engine malfunction light on (8.2.1.2 (b)) | 1 |
| Nearside Front Vehicle structure is deformed and structural rigidity is significantly reduced chassis |6.1.1 |a| |i|| | 1 |
| Offside Rear Outer Vehicle structure is deformed and structural rigidity is significantly reduced sill |6.1.1 |a| |i|| | 1 |
| Offside Rear Outer Vehicle structure is deformed and structural rigidity is significantly reduced sill missing |6.1.1 |a| |i|| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 1 |
| Electrical wiring insecure under bonnet |1.9.2a| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear inner and outer sill (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded nearside rear inner sill |5.2.6| | 1 |
| Fuel pipe leaking excessively or a risk of fire Fuel line leaking at flexi hose ............. (6.1.3 (b) (ii)) | 1 |
| Nearside Front Headlamp light intensity severely reduced Nearside front headlamp poor image /poor light output.......... (4.1.4 (a)) | 1 |
| Front Brake disc significantly and obviously worn Both front brake discs badly corroded and pitted /poor condition.......... (1.1.14 (a) (i)) | 1 |
| Rear Brake disc significantly and obviously worn Both rear brake discs badly corroded and poor condition............. (1.1.14 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis by anti rollbar |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis by anti rollbar |2.4.A.3| | 1 |
| Offside Rear Road wheel cracked |4.2.A.1a| | 1 |
| Offside Parking brake recording little or no effort |3.7.D.3a| | 1 |
| Rear Service brake application uneven across the axle |3.7.D.2b| | 1 |
| Nearside Front Outer Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively damaged significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Emissions not tested due to engine water leak (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassic (5.3.6 (a) (i)) | 1 |
| Offside Steering locking device missing (2.1.3 (d)) | 1 |
| Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings area marked in yellow |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings area marked in yellow |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings area marked in yellow |6.1.B.2| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg corroded with in prescribed area of top arm mounting point (5.3.6 (a) (i)) | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner and outer sill |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner and outer sill |6.1.B.2| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch 2 places |6.2.2 |d| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill areas holed through corrosion. (5.3.6 (a) (i)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users power steering |8.4.1 |a| |i|| | 1 |
| Emissions unable to be completed engine cut out will not restart (8.2.1.2 (d)) | 1 |
| Nearside Front Upper Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded inner wing (2.1.2 (e) (i)) | 1 |
| Drivers view of an obligatory external mirror significantly affected by an obstruction (3.1 (a) (ii)) | 1 |
| Nearside Front Upper Steering linkage ball joint ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Upper Steering linkage ball joint ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill panel (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases unable to do emmisions test |7.1.2| | 1 |
| Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Outer Sill |5.2.6| | 1 |
| Front Service brake excessively binding n/s & o/s |1.2.1 |f|| | 1 |
| Exhaust has a major leak of exhaust gases Rear exhaust joint. Centre and rear exhaust sections (6.1.2 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced nearside rear inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner SIL - Marked with chalk (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner SIL - Marked with chalk (6.1.1 (c) (i)) | 1 |
| Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt N/S and O/S Outer dust covers (5.3.4 (b) (ii)) | 1 |
| Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt N/S and O/S Outer dust covers (5.3.4 (b) (ii)) | 1 |
| Nearside Subframe mounting prescribed area is excessively corroded outer sill holed |2.4.A.3| | 1 |
| Offside Subframe mounting prescribed area is excessively corroded outer sill holed |2.4.A.3| | 1 |
| Nearside Rear brake caliper has restricted free movement brake binding |3.5.1k| | 1 |
| Nearside Front Anti-roll bar insecure anti roll bar bush worn |2.4.G.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases rear box us |7.1.2| | 1 |
| Exhaust has a major leak of exhaust gases joint at rear silencer |6.1.2 |a|| | 1 |
| Nearside Rear Cab or chassis has excessive corrosion to the extent that overall security or stability of the cab is impaired outter sll (6.2.2 (d) (ii)) | 1 |
| Offside Rear Cab or chassis has excessive corrosion to the extent that overall security or stability of the cab is impaired outter sill (6.2.2 (d) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases Centre to rear silencer joint very badly corroded. |7.1.2| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Outer sill area. |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill and end cap of sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner/outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Brake performance not tested leaking |1.2.1 |g|| | 1 |
| Nearside Front Power steering ram leaking |2.1.5 |a|| | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases joint into tail box (6.1.2 (a)) | 1 |
| brake caliper has restricted free movement binding |3.5.1k| | 1 |
| Rear Seat belt anchorage prescribed area is excessively corroded sills both sides |5.2.6| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced A pillar corroded (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure has a fracture which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Upper Suspension arm corroded and seriously weakened rotted out and insecure |2.4.G.1| | 1 |
| Power steering pipe/hose leaking low pressure pipe from hose (2.1.5 (a)) | 1 |
| Nearside Rear Braking system leaking at caliper |3.6.A.1| | 1 |
| Offside Front Anti-roll bar linkage corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill front jacking point |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor pan |6.1.1 |c| |i|| | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheelarch (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced a post (6.1.1 (c) (i)) | 1 |
| Emissions unable to be completed unable to hold at a suitable rev range (8.2.1.2 (d)) | 1 |
| Nearside Front Lower Suspension arm corroded and seriously weakened corrosion at shocker mount point (5.3.3 (b) (i)) | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened corrosion at shocker mount point (5.3.3 (b) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills rotted |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills rotted |7.1.1 |a| |i|| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 1 |
| Fuel cap/sealing device missing Unable to open the fuel flap |7.2.4a| | 1 |
| Nearside Front Anti-lock braking system wiring excessively damaged ABS wiring cut (1.6 (d)) | 1 |
| Offside Front Anti-lock braking system wiring excessively damaged ABS wiring cut (1.6 (d)) | 1 |
| Front Position lamp not working both nearside and offside (4.2.1 (a) (ii)) | 1 |
| Nearside Inner brake disc excessively pitted |3.5.1h| | 1 |
| Offside Rear coil spring broken (2.4.C.1a) | 1 |
| Offside Front front brake binding (3.7.B.1) | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting chassis leg (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section anti roll bar/subframe mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section anti roll bar/subframe mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg | under wheel arch | |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill rear closing panel (7.1.1 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor pan (5.3.6 (a) (i)) | 1 |
| Emissions not tested Cat Missing (8.2.1.2 (d)) | 1 |
| Offside Lower Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Offside Front Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected inner wing |5.3.6 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wing |5.3.6 |a| |ii|| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings o s outer sill |6.1.B.2| | 1 |
| Emissions not tested LEAK (8.2.1.2 (d)) | 1 |
| Position lamp not working FRONTS (4.2.1 (a) (ii)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting N/S SILL TO FLOOR (6.2.2 (d) (i)) | 1 |
| Track rod end ball joint has excessive play N/S AND O/S (2.1.3 (b) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired Inner/Outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired Inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion to inner and outer sill (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases middle/rear |7.1.2| | 1 |
| Seat belt anchorage prescribed area is excessively corroded o/s outer sill |5.2.6| | 1 |
| brake disc in such a condition that it is seriously weakened n/s rear |3.5.1i| | 1 |
| brake disc in such a condition that it is seriously weakened o/s rear |3.5.1i| | 1 |
| Nearside Front Position lamp not working side light bulb 501 (4.2.1 (a) (ii)) | 1 |
| Offside Front Position lamp not working side light bulb 501 (4.2.1 (a) (ii)) | 1 |
| Offside Headlamp insecure and damaged on secure brackets (4.1.1 (c)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch |6.2.2 |d| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner and outer sill |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis area |6.2.2 |d| |i|| | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases rear silencer leaking (6.1.2 (a)) | 1 |
| Nearside Rear Exhaust emissions likely to be affected by an exhaust leak exhaust leak at rear silencer (8.2.1.1 (b)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor under seat |5.2.6| | 1 |
| Speedometer clearly inoperative |6.7.2| | 1 |
| Nearside Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Hydraulic brake calliper leaking |1.1.16 |b| |i|| | 1 |
| Nearside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting sill |6.2.2 |d| |i|| | 1 |
| Offside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Sill |6.2.2 |d| |i|| | 1 |
| Offside Rear Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting sill |6.2.2 |d| |i|| | 1 |
| Front Position lamp not working Both side (4.2.1 (a) (ii)) | 1 |
| Central Electrical wiring likely to drag on the ground (4.11 (a) (iii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis inner wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis inner wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mounting point (5.3.6 (a) (i)) | 1 |
| Nearside Front brake disc contaminated by oil |3.5.1h| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis in wheel arch area (6.1.1 (c) (i)) | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded front |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Seal (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Seal (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed catalytic converter removed (8.2.1.2 (d)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner seal (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer seal (6.1.1 (c) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area and inner wheel arch (7.1.1 (a) (i)) | 1 |
| Brake performance unable to be tested due to engine failure (1.2.1 (g)) | 1 |
| Brake performance not tested nearside front caliper insecure (1.2.1 (g)) | 1 |
| Nearside Front Hydraulic brake calliper insecurely mounted and braking performance affected bolt missing (1.1.16 (c) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Offside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill area (7.1.1 (a) (i)) | 1 |
| Nearside Front Hydraulic brake calliper inadequately mounted and braking performance affected lower bolt missing from caliper (1.1.16 (c) (ii)) | 1 |
| Brake performance not tested due to bolts missing from nsf caliper (1.2.1 (g)) | 1 |
| Emissions unable to be completed ENGINE STARTED HUNTING,EML CAME ON.ENGINE STALLED. (8.2.1.2 (d)) | 1 |
| Side repeater not working NS / OS (4.4.1 (a) (ii)) | 1 |
| Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wings by anti roll bar mounts both sides (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Middle to rear section is leaking. (6.1.2 (a)) | 1 |
| Fuel cap/sealing device ineffective Fuel cap seal heavily perished. (6.1.3 (b) (i)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Offside wheel arch, down to the seal is heavily corroded through. (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Offside rear wheel arch down to the seal is heavily corroded through (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Nearside seal is heavily corroded through. (6.2.2 (d) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn D bushes (5.3.4 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded. Both inner and outer (7.1.1 (a) (i)) | 1 |
| Nearside Front Braking system leaking calliper bleeder |3.6.A.1| | 1 |
| Offside Front Seat belt anchorage loose (7.1.1 (b)) | 1 |
| Windscreen wiper missing (3.4 (a)) | 1 |
| Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill/Floor. (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Upper-Inner Arch - Strut Mount. (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced above anti role bar (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced above anti role bar (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired inner sill plated not continuous welding (7.1.1 (a) (i)) | 1 |
| Offside Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor/ wheel well (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced inner wheel wheel/arch not continuous welding (6.1.1 (d) (i)) | 1 |
| Nearside Front Body insecure to the extent that stability is seriously impaired inner leg (6.2.2 (a) (ii)) | 1 |
| Offside Front Body insecure to the extent that stability is seriously impaired leg (6.2.2 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Brake master cylinder/servo mounting prescribed area is excessively corroded wing (1.1.21 (e) (i)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases rear join (6.1.2 (a)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Lower Seat belt anchorage prescribed area is inadequately repaired outer sill, repair not fully seam welded (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Brake cable has restricted free movement |3.5.1k| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill x2 bits |7.1.1 |a| |i|| | 1 |
| Nearside Direction indicator incorrect colour an offside wing indicators (4.4.3 (a)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect misted (4.1.2 (c)) | 1 |
| Nearside Rear Position lamp not working and offside rear (4.2.1 (a) (ii)) | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering anti roll bar mounting |6.1.A.1| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering anti roll bar mounting |6.1.A.1| | 1 |
| Nearside Stop lamp|s| showing white light to the rear lamp unit lens broken |4.3.3 |a| |ii|| | 1 |
| Offside Rear Lower Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Nearside Front Road wheel fixing missing wheel nut missing. (5.2.1 (a) (i)) | 1 |
| Offside Front Road wheel fixing missing wheel nut missing. (5.2.1 (a) (i)) | 1 |
| Nearside Rear Road wheel fixing missing wheel nut missing. (5.2.1 (a) (i)) | 1 |
| Offside Rear Road wheel fixing missing wheel nut missing. (5.2.1 (a) (i)) | 1 |
| Front Electrical wiring likely to touch hot or rotating parts lamda sensor wire tied to exhaust. (4.11 (a) (iii)) | 1 |
| Brake lever has insufficient reserve travel parking brake lever. (1.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg/ filler present (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill box section (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill box section (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mount area chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mount area chassis (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Centre to Rear flange joint rotten away (6.1.2 (a)) | 1 |
| Offside Subframe mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (outer seal ) (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/floor pan |6.1.1 |c| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail where the anti roll bar mounts (5.3.6 (a) (i)) | 1 |
| brake disc in such a condition that it is seriously weakened both front
|3.5.1i| | 1 |
| brake disc in such a condition that it is seriously weakened both rear
|3.5.1i| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis
|2.4.A.3| | 1 |
| Headlamp lens seriously defective Both (4.1.1 (b) (ii)) | 1 |
| Headlamp aim projected beam image is obviously incorrect Both (4.1.2 (c)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside arch |5.3.6 |a| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Under headlamp (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Boot floor (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Mid pipe to back box joint (6.1.2 (a)) | 1 |
| Emissions not tested Due to major exhaust fume leak (8.2.1.2 (d)) | 1 |
| Exhaust has a major leak of exhaust gases middle box |7.1.2| | 1 |
| Nearside Windscreen wiper blade missing (3.4 (b) (ii)) | 1 |
| Offside Windscreen wiper blade missing (3.4 (b) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis section (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis section (5.3.6 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced battery area (6.1.1 (c) (i)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases join corroded (6.1.2 (a)) | 1 |
| Position lamp not working N/s Front (4.2.1 (a) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Sub-frame cracked |2.4.G.1| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nearside sill |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside sill |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside rear floor to sill |7.1.1 |a| |i|| | 1 |
| Offside Front Braking system leaking Calliper |3.6.A.1| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced seat belt mounting |outer sill| |7.1.1 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Wheel arch |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Wheel arch |6.1.B.2| | 1 |
| Exhaust has a major leak of exhaust gases middle and rear (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/floor area and lower arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Anti Roll Bar mounting to chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill has corroded within 30 cm of seat belt mounting (7.1.1 (a) (i)) | 1 |
| Rear Fuel pipe union leaking |7.2.3| | 1 |
| Nearside Rear Anti-roll bar has excessive play in a ball joint insecure |2.4.G.2| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill - rear |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill - rear |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within 30cm of anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Wheel Arch (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Wheel Arch (6.2.2 (d) (i)) | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Behind bumper (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Behind Bumper (6.1.1 (c) (i)) | 1 |
| Central Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Behind Bumper (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Road wheel fixing missing all four wheels |5.2.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front chassis holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front chassis holed (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mounting |5.3.6 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nearside outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor/sill. |7.1.1 |a| |i|| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor/sill. |7.1.1 |a| |i|| | 1 |
| Front Headlamp aim not tested |4.1.2 |b|| | 1 |
| Offside Suspension rod ball joint dust cover no longer prevents the ingress of dirt Both top and bottom ball joint rubbers (5.3.4 (b) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill panel corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floorpan |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded under inner sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded under inner sill |5.2.6| | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected wing |5.3.6 |a| |ii|| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
| Central Stop lamp not working (1.2.1b) | 1 |
| Offside Rear brake caliper leaking (3.6.A.1) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting end sill pannel (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting end sill pannel (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Cab or chassis has excessive corrosion to the extent that overall security or stability of the cab is impaired boot floor holed (6.2.2 (d) (ii)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch side of liner (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill
|5.2.6| | 1 |
| Nearside Rear Brake valve leaking brake caliper leaking (1.1.7 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre exhaust broken |7.1.2| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded LOWER CHASSIS RAIL |2.4.A.3| | 1 |
| Offside Front Inner Subframe mounting prescribed area is excessively corroded WHEEL ARCH TO CHASSIS RAIL |2.4.A.3| | 1 |
| Nearside Rear Fluid leaking continuously posing a serious risk to road safety brake caliper |8.4.1 |a| |ii|| | 1 |
| Nearside Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer seal (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Excessively corroded. (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced N/s , o/s inner wheel arches |7.1.1 |a| |i|| | 1 |
| Brake reservoir fluid level decreases after several pedal applications |3.3.C.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis at sway bar mounting bracket (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Service brake excessively binding 35+ kgf (1.2.1 (f)) | 1 |
| Offside Rear Upper Suspension arm likely to become detached arm corroded and broken away (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arm (5.3.6 (a) (i)) | 1 |
| Parking brake lever inappropriately modified |3.1.8| | 1 |
| Parking brake lever pawl spring does not push the pawl positively into the ratchet teeth |3.1.5| | 1 |
| Nearside Rear Coil spring fractured or broken TOP IS BROKEN (5.3.1 (b) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt SPLIT (5.3.4 (b) (ii)) | 1 |
| Offside Rear Suspension arm ball joint dust cover no longer prevents the ingress of dirt SPLIT (5.3.4 (b) (ii)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner wing area |2.4.A.3| | 1 |
| Front Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Main beam tell-tale not working illuminated with dipped beam lights as well (4.9.1 (a) (ii)) | 1 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced within 30 cm of seat mount (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Catalytic converter (6.1.2 (a)) | 1 |
| Nearside Front Vehicle structure inadequately repaired such that structural rigidity is significantly reduced Chassis (6.1.1 (d) (i)) | 1 |
| Offside Front Vehicle structure inadequately repaired such that structural rigidity is significantly reduced Chassis (6.1.1 (d) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is inadequately repaired Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill return |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill return |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded rear of sill at axle mounting |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded all around chassis leg |2.4.A.3| | 1 |
| Nearside Rear Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill. |6.1.B.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded ANTI ROLL BAR MOUNTING |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded ANTI ROLL BAR MOUNTING |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded SILL |2.4.A.3| | 1 |
| Nearside Front Brake slack adjuster has restricted free movement |1.1.15 |e|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to floor 2 holes |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to floor 2 holes |6.1.1 |c| |i|| | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s and n/s inner wheel arches as marked (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced above drivers wheel (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch (6.2.2 (d) (i)) | 1 |
| Rear Lower Anti-roll bar linkage ball joint excessively worn both sides (5.3.4 (a) (i)) | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened sill (5.3.3 (b) (i)) | 1 |
| Offside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened sill (5.3.3 (b) (i)) | 1 |
| Offside Front Suspension arm attachment bracket/mounting corroded and seriously weakened sill and floorpan (5.3.3 (b) (i)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Rear Exhaust has a major leak of exhaust gases joint between rear silencer and system (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded SILL |2.4.A.3| | 1 |
| Nearside Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Rear Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced sill (6.1.1 (b) (ii)) | 1 |
| Offside Rear Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced rear boot floor (6.1.1 (b) (ii)) | 1 |
| Offside Outer Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Outer Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both side rear inner wheel arches (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both side rear inner sills (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded both side rear sills |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded offside rear floorpan |5.2.6| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings rear sill |6.1.B.2| | 1 |
| Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Both front inner wheel arch chassis (6.2.2 (d) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases flange (6.1.2 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced on floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced on sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail with in 30 cm of sub frame mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Front position lamp|s| not working sometimes it comes on for a split second then goes out again |1.1.A.3b| | 1 |
| Offside Rear Front position lamp|s| not working flickering on and off all the time |1.1.A.3b| | 1 |
| Nearside Rear Wheel nut|s| loose wheel insecure at hub |4.2.A.1e| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill and floor pan |5.2.6| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded chassis leg beside steering rack mount |2.1.2 |e| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected floor |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at floor |5.3.6 |a| |i|| | 1 |
| Offside Outer Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassi |6.1.B.2| | 1 |
| Brake performance not tested fluid leak from os rear caliper (1.2.1 (g)) | 1 |
| Offside Rear Hydraulic brake calliper leaking from handbrake pivot (1.1.16 (b) (i)) | 1 |
| Offside Side repeater missing |4.4.1 |a| |ii|| | 1 |
| Main beam tell-tale not working Staying on |4.9.1 |a| |ii|| | 1 |
| Rear reflector missing |4.8.2 |a| |ii|| | 1 |
| Rear Exhaust has a major leak of exhaust gases flange corroded away |7.1.2| | 1 |
| Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength both sides (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis/inner wheel arch (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre and rear (6.1.2 (a)) | 1 |
| Exhaust has a major leak of exhaust gases Middle to back box (6.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis holed around antiroll bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings box section of chassis (6.1.B.2) | 1 |
| Nearside Rear brake disc excessively pitted (3.5.1h) | 1 |
| Offside Rear brake disc excessively pitted (3.5.1h) | 1 |
| Service brake: efficiency below requirements (3.7.B.7) | 1 |
| Rear Parking brake lever has no reserve travel (3.1.6b) | 1 |
| Rear Inner brake disc in such a condition that it is seriously weakened (3.5.1i) | 1 |
| Rear Braking system leaking METAL BRAKE PIPE (3.6.A.1) | 1 |
| Brake fluid warning lamp illuminated (3.6.G.2) | 1 |
| Nearside Rear coil spring corroded so that its cross sectional area is reduced and seriously weakened (2.4.C.1b) | 1 |
| Offside Rear coil spring corroded so that its cross sectional area is reduced and seriously weakened (2.4.C.1b) | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings OUTER SILL HOLED (6.1.B.2) | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened (2.4.G.1) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel Arch Sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch Sill |5.3.6 |a| |i|| | 1 |
| Headlamp aim projected beam image is obviously incorrect x2 (4.1.2 (c)) | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened Rusted though where marked |5.3.3 |b| |i|| | 1 |
| Offside Lower Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail near o/s front anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill back (7.1.1 (a) (i)) | 1 |
| Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor /chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor /chassis (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded nearside outer sill |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Rear outer sill |5.2.6| | 1 |
| Nearside Rear coil spring worn so that its cross sectional area is reduced and seriously weakened |2.4.C.1b| | 1 |
| Nearside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing to sill |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill section |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings filler |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings boot floor |battery area| |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing to floor section |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings rear floor section |6.1.B.2| | 1 |
| Nearside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced seal |6.1.1 |c| |i|| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings underbody inner sill |6.1.B.2| | 1 |
| Offside Obligatory mirror does not provide a view to the rear (3.3 (c)) | 1 |
| Front Road wheel fixing missing |5.2.1 |a| |i|| | 1 |
| Offside Rear Rear reflector defective or damaged by more than 50% of the reflecting surface |4.8.1 |a| |ii|| | 1 |
| Rear Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Offside Rear Vehicle structure strengthening plate or fastening insecure bolt broken (6.1.1 (b) (i)) | 1 |
| Brake lever has abnormal movement of levers indicating maladjustment |3.5.1f| | 1 |
| Nearside Outer Rear Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Offside Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Both front & both rear inner & outer sills |6.1.1 |c| |i|| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Offside rear inner Lower arch |6.1.1 |c| |i|| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch qtr (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is inadequately repaired qtr cill (5.3.6 (a) (i)) | 1 |
| Electrical wiring insecure and in contact with sharp edges under side of vehicle |4.11 |a| |ii|| | 1 |
| Offside Rear Parking brake operation is causing the vehicle to swerve to the nearside hand brake not working (1.4.1 (a) (i)) | 1 |
| Emissions unable to be completed Vehicle overheated (8.2.1.2 (d)) | 1 |
| Brake performance unable to be tested Vehicle overheated (1.2.1 (g)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wing
|2.4.A.3| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wing/chassis |2.4.A.3| | 1 |
| Position lamp switch does not illuminate the front and rear position lamps with a single operation no bulbs in the front side lights (4.2.2 (a)) | 1 |
| Offside Subframe mounting prescribed area is excessively corroded sill . outer at front. inner at rear |2.4.A.3| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded floor both sides |2.4.A.3| | 1 |
| Nearside Rear Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Brake disc in such a condition that it is seriously weakened both rears (1.1.14 (a) (ii)) | 1 |
| Service brake excessively binding both fronts (1.2.1 (f)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor/sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor/sill (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor/sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Inner Body has a projection caused by corrosion wing |6.1.C.1| | 1 |
| Offside Front Inner Body has a projection caused by corrosion wing |6.1.C.1| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bearing BROKEN |2.4.G.2| | 1 |
| Offside Rear Inner Subframe mounting prescribed area is excessively corroded wheel arch corroded and holed |2.4.A.3| | 1 |
| Front position lamp|s| not working both front sidelight |1.1.A.3b| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sil |6.1.B.2| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sil |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sil |6.1.B.2| | 1 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sil |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired sill area (floor wheel arch) (7.1.1 (a) (i)) | 1 |
| Front brake disc contaminated by oil |3.5.1h| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor holed |5.2.6| | 1 |
| Offside Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 1 |
| Nearside Rear Suspension arm locating pin retaining device not properly locked |2.4.G.3b| | 1 |
| Offside Outer Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Both sides outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension arm corroded and seriously weakened and offside rear |2.4.G.1| | 1 |
| Nearside Rear Suspension arm corroded and seriously weakened lower wishbone |2.4.G.1| | 1 |
| Offside Rear Suspension arm corroded and seriously weakened lower wishbone |2.4.G.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corroded |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis floor corroded |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength floor |5.3.6 |a| |i|| | 1 |
| Offside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting insecure linkage lower mount on arm corroded and broken |2.4.G.1| | 1 |
| Nearside Front position lamp|s| not working and offside |1.1.A.3b| | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Nearside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting nsr wheel arch inner lower corrosion (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting offside full side sill corrosion from back all the way to front of car (6.2.2 (d) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner will to floor pan |5.2.6| | 1 |
| Front Brake pipe leaking to rear |3.6.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at anti roll bar anchorage (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Anti-lock braking system component missing front cables ? (1.6 (e)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn nut loose (5.3.4 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer wheel arch (5.3.6 (a) (i)) | 1 |
| Power steering component leaking fluid dripping from around reservoir (2.1.5 (a)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor/sill (6.2.2 (d) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both inner sills (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting likely to become detached bolt missing (5.3.3 (a) (ii)) | 1 |
| Suspension arm ball joint likely to become detached x4 front upper and lower (5.3.4 (a) (ii)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded both sill |5.2.6| | 1 |
| Front Electrical wiring likely to touch hot or rotating parts lambda sensor |4.11 |a| |iii|| | 1 |
| Rear Electrical wiring likely to touch hot or rotating parts lambda sensor |4.11 |a| |iii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top wish bone prescribed area |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top wishbone |5.3.6 |a| |i|| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting insecure Mounting pulled out of lower arm (5.3.3 (a) (i)) | 1 |
| Brake disc significantly and obviously worn both at inner faces (1.1.14 (a) (i)) | 1 |
| Rear Brake disc significantly and obviously worn both (1.1.14 (a) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction Cleared codes P0037 & P0130 - O2 heater circuit (8.2.1.2 (h)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction sun strip (3.1 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis rail |5.3.3 |b| |i|| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting damaged and seriously weakened chassis rail |5.3.3 |b| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sills |7.1.1 |a| |i|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sills |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sills |7.1.1 |a| |i|| | 1 |
| Nearside Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened |5.3.1 |b| |i|| | 1 |
| Rear Sub-frame corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Front Sub-frame corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Front Body mounting fixings insecure wing |6.2.2 |c| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/arch (7.1.1 (a) (i)) | 1 |
| Suspension arm corroded and seriously weakened at anti roll link mount (5.3.3 (b) (i)) | 1 |
| Offside Rear Suspension arm corroded and seriously weakened at anti roll link mount (5.3.3 (b) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill at rear (6.2.2 (d) (i)) | 1 |
| Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER WHEEL ARCH |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER WHEEL ARCH |6.1.B.2| | 1 |
| Seat belt anchorage prescribed area is excessively corroded both rear floor corners corroded to excess within 30cm of seat belt anchorage |5.2.6| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded chassis |2.2.C.1h| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill at rear |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill at rear |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Lower outer sill |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Floor pan painted white |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Subframe corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Sub frame corroded |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Front inner chassis painted white |2.4.A.3| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint drop link |2.4.G.2| | 1 |
| Nearside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to floor (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded closing panel |5.2.6| | 1 |
| Nearside Front Inner Subframe mounting prescribed area is excessively corroded sill. |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis rail. |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting area (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn drop link (5.3.4 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chalked |6.1.B.2| | 1 |
| Offside Front Anti-roll bar missing |2.4.G.1| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced body sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced body sill |7.1.1 |a| |i|| | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor to sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Emissions not tested engine overheated |7.3.A.1| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both rears sills |5.3.6 |a| |i|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Arch |6.1.1 |c| |i|| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Arch |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings ho;e in os/r sill |6.1.B.2| | 1 |
| Offside rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill back (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill end wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill end wheel arch (7.1.1 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength off and nearside front chassis |5.3.6 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside rear inner arch |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside rear sill back |7.1.1 |a| |i|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength offside front floor |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected antiroll bar mounting point (5.3.6 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jack point and floor (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jack point and floor (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill to floor mid way (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength antiroll bar mounting point (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded both rear inner arches, offside rear floor, nearside rear inner sill |5.2.6| | 1 |
| Suspension component mounting prescribed area is excessively corroded offside front floor, rear inner sills and arches |2.4.A.3| | 1 |
| Nearside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Lower Tie bar/rod insecure |2.4.G.1| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint vertical link bar |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint vertical link bar |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer cill corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer cill corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis section corroded (5.3.6 (a) (i)) | 1 |
| Nearside Front Front suspension has a suspension lower ball joint securing nut loose |2.5.B.1a| | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor pan (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Steering locking device ineffective Ball joint securing bolt too short rendering the nylock nut inadequate (2.1.3 (d)) | 1 |
| Nearside Headlamp has a product on the lens which changes emitted colour to other than white or yellow (4.1.4 (b)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor (7.1.1 (a) (i)) | 1 |
| Front Power steering pipe/hose excessively corroded all |2.1.5 |g| |i|| | 1 |
| Nearside Front Upper Vehicle structure has excessive corrosion which adversely affects braking or steering top/bottom/inner/outer/chassis/as/marked |6.1.1 |c| |ii|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering top/bottom/inner/outer/chassis/as/marked |6.1.1 |c| |ii|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner/sill/to/floor |6.1.1 |c| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired chassis (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength Floor panel (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected SILL + INNER SILL (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected SILL + INNER SILL (5.3.6 (a) (ii)) | 1 |
| Front Power steering pipe/hose leaking At cradle (2.1.5 (a)) | 1 |
| Front Power steering pipe/hose excessively corroded At cradle (2.1.5 (g) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength A large section of inner wheel arch missing, due to corrosion within 30 cm top mounting. (5.3.6 (a) (i)) | 1 |
| Front Power steering inoperative and steering adversely affected (2.1.5 (c) (ii)) | 1 |
| Nearside Front Power steering fluid reservoir empty (2.1.5 (b) (ii)) | 1 |
| Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 1 |
| Offside Front Anti-roll bar linkage insecurely attached drop link detached. |5.3.3 |a| |i|| | 1 |
| Nearside Front Lower Body has a sharp edge caused by corrosion Wing |6.1.C.1| | 1 |
| Offside Front Lower Body has a sharp edge caused by corrosion Wing |6.1.C.1| | 1 |
| Nearside Rear Lower Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Lower Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Tie bar/rod insecure |2.4.G.1| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded floor/chassis |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg almost completely missing with attempted repair with cardboard |2.4.A.3| | 1 |
| Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Front Upper Suspension arm ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm has excessive play in a pin/bush ball joint |2.4.G.2| | 1 |
| Nearside Front Upper Fluid suspension unit leaking |2.4.D.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis above whishbone front mount |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing and chassis |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill to floor |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill to floor |2.4.A.3| | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded both end sill |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting point |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting point |5.3.6 |a| |i|| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chasis |in wheel arch| |5.3.6 |a| |i|| | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis |in wheel arch| |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL |5.3.6 |a| |i|| | 1 |
| Front Suspension arm corroded and seriously weakened All front |5.3.3 |b| |i|| | 1 |
| Offside Rear Anti-roll bar locating pin retaining device not properly locked |2.4.G.3b| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded center floor /inner sill corroded and holed |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded center floor/inner sill corroded and holed |5.2.6| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded floor/inner sill front & rear |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering anti roll bar mounting |6.1.A.1| | 1 |
| Offside Front Road wheel fixing missing |5.2.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced undersill and inner wheel archj (7.1.1 (a) (i)) | 1 |
| Nearside Rear Brake valve leaking caliper leaking (1.1.7 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg underside (5.3.6 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| front brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Wing (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Subframe mounting prescribed area excessively corroded significantly reducing structural strength Floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail before upper wishbone |2.4.A.3| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie leg anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie leg anti rollbar mounting |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension arm attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Rear Vehicle structure has an inadequate repair which adversely affects braking or steering |6.1.A.1| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Hydraulic brake calliper leaking possible bleed nipple (1.1.16 (b) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill area holes and cracked (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill corroded and holed |5.2.6| | 1 |
| Nearside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
| Parking brake lever defective so that it cannot be satisfactorily operated button not release |1.1.6 |d|| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Parking brake efficiency below requirements 14%. offside rear parking brake low effort |1.4.2 |a| |i|| | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting footwell |6.2.2 |d| |i|| | 1 |
| Offside Front Upper Suspension arm ball joint likely to become detached retaining device missing |5.3.4 |a| |ii|| | 1 |
| Offside Suspension arm ball joint likely to become detached track rod end retaining device missing |5.3.4 |a| |ii|| | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached retaining device missing |5.3.4 |a| |ii|| | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached retaining device missing |5.3.4 |a| |ii|| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt split (5.3.4 (b) (ii)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded, holed (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill corroded,holed (5.3.6 (a) (i)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer body sill corrosion (7.1.1 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill holed |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg . roll bar mount moves . |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Front Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength floor |5.3.6 |a| |i|| | 1 |
| Nearside Front Braking system leaking flexible pipe / caliper |1.1.3 |d|| | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill (6.1.1 (c) (ii)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak join rear silencer |8.2.1.1 |b|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch marked yellow |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch marked yellow |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch, marked yellow |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch, marked yellow |7.1.1 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outersill (5.3.6 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wing (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wing (5.3.6 (a) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced mid section inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Floor excessively deteriorated battery mounting (6.2.4 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail |6.1.1 |c| |i|| | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s and n/s inner sills to floor and o/s/r inner sill to outer sill. (6.2.2 (d) (i)) | 1 |
| Nearside Rear Braking system leaking claiper |3.6.A.1| | 1 |
| Nearside Rear Inner Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail under arch |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under arch chassis rail |6.1.B.2| | 1 |
| Offside Front Lower Steering linkage ball joint has excessive play |2.1.3 |b| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch front and rear of |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear of inner arch |6.1.1 |c| |i|| | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both sides inner arch front of |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to inner sill 2 areas |6.1.1 |c| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced body out rigger to floor panel |6.1.1 |c| |i|| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 1 |
| Offside Front Braking system leaking master cylinder |3.6.A.1| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill & rear wheel arch |7.1.1 |a| |i|| | 1 |
| Brake performance not tested Front to rear brake pipe burst severe corrosion |3.7.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner sill |6.1.A.1| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure bolt missing from mounting bracket (5.3.3 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded rear sill |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded rear sill |2.4.A.3| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed and rusty (5.3.6 (a) (i)) | 1 |
| Front Track rod end seriously misaligned both sides toeing out (2.1.3 (e)) | 1 |
| Rear Anti-roll bar missing (5.3.3 (a) (ii)) | 1 |
| Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Fuel system component leaking Filter |7.2.3| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor. |6.1.1 |c| |i|| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both rear inner sill sections. |6.1.1 |c| |i|| | 1 |
| Anti-roll bar linkage ball joint excessively worn both front. |5.3.4 |a| |i|| | 1 |
| Offside Front Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Wheel nut|s| loose |4.2.A.1e| | 1 |
| Nearside Front Coil spring fractured or broken broken (5.3.1 (b) (i)) | 1 |
| Nearside Front Upper Coil spring not correctly located |2.4.C.2| | 1 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired outer sill patch not continuously welded |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired outer sill patch not continuously welded |7.1.1 |a| |i|| | 1 |
| Nearside Power steering pipe/hose leaking |2.1.5 |a|| | 1 |
| Offside Front Integral body structure inadequately repaired such that structural rigidity is significantly reduced floor to sill (6.1.1 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer and inner sills (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front and rear inner and outer sills both sides x 6 holes all marked with chalk (5.3.6 (a) (i)) | 1 |
| Parking brake not fitted on at least two wheels |3.1.1| | 1 |
| Offside Front Anti-roll bar linkage inappropriately repaired |2.4.A.2| | 1 |
| rear brake recording little or no effort no readings both sides |3.7.B.5a| | 1 |
| Rear Braking system leaking main pipe |3.6.A.1| | 1 |
| Centre Exhaust has a major leak of exhaust gases section to rear silencer |7.1.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded floor to inner sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded floor to inner sill |5.2.6| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Hazard warning switch inoperative missing (4.4.2 (a) (ii)) | 1 |
| Front Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction opaque on windscreen (3.1 (a) (ii)) | 1 |
| Front Anti-roll bar has excessive play in a ball joint both |2.4.G.2| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Lower seat belt mount |5.2.6| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Under wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp lens seriously defective No beam pattern (4.1.1 (b) (ii)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner and outer sill (6.1.1 (c) (i)) | 1 |
| Front Integral body structure has a fractured which is likely to adversely affect braking or steering chassis legs/box section both sides (6.1.1 (a) (ii)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor/battery tray (6.1.1 (c) (i)) | 1 |
| Integral body structure inadequately repaired such that structural rigidity is significantly reduced both outer sills (6.1.1 (d) (i)) | 1 |
| Offside Front Wheel stud|s| missing |4.2.A.1e| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected |4.11 |a| |ii|| | 1 |
| Passenger`s airbag missing |7.1.5 |a|| | 1 |
| Rear Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Hazard warning lamps inoperative all |1.4.B.1b| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected spring mounting to ant roll bar mounting on main chassi (5.3.6 (a) (ii)) | 1 |
| Suspension component mounting prescribed area is excessively corroded both rear closing panels |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner flitch / end of sill |2.4.A.3| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch by bumper mountings (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch by bumper mountings (6.2.2 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases backbox join |7.1.2| | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill/floor (6.2.2 (d) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side cable disconnected (1.4.1 (a)) | 1 |
| Offside Front Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced tail end of sill inside wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced tail end of sill inside wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired Sills are repaired with filler. Area marked on offside sill can be felt to be crushed under thumb pressure (7.1.1 (a) (i)) | 1 |
| Body has a sharp edge caused by damage offside rear bumper |6.1.C.1| | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg / box corroded and damaged |6.1.A.1| | 1 |
| Offside Rear Brake pipe connection leaking on an air braking system |1.1.11 |b| |i|| | 1 |
| Offside Front Upper Coil spring fractured or broken |5.3.1 |b| |i|| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Vehicle structure is fractured and structural rigidity is significantly reduced Marked yellow (6.1.1 (a) (i)) | 1 |
| Nearside Rear Floor excessively deteriorated Boot floor holed (6.2.4 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Front of inner sill holed (6.1.1 (c) (i)) | 1 |
| Fuel cap/sealing device sealing washer deteriorated |7.2.4c| | 1 |
| Nearside Front Body panel insecure wing (6.2.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear sill inner (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear sill outer (7.1.1 (a) (i)) | 1 |
| Central Brake pipe likely to become detached or damaged (1.1.11 (d) (ii)) | 1 |
| Offside Front Anti-roll bar ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Offside Drivers airbag missing (7.1.5 (a)) | 1 |
| Nearside Front Sub-frame strengthening plate or fastening insecure rear bolt missing (6.1.1 (b) (i)) | 1 |
| Offside Front Sub-frame strengthening plate or fastening insecure rear bolt missing (6.1.1 (b) (i)) | 1 |
| Exhaust has a major leak of exhaust gases middle box (6.1.2 (a)) | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition middle (8.1.1 (a)) | 1 |
| Inner Front brake disc excessively scored |3.5.1h| | 1 |
| Offside Rear Outer Body component corroded and likely to cause injury wing (6.2.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength main leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting chassis corroded front outer side (6.2.2 (d) (i)) | 1 |
| Offside Front Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting chassis leg corroded front outer side (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sturt top area |5.3.6 |a| |i|| | 1 |
| Offside Rear Tie bar/rod insecure anti roll bar link pin broken |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis to front of subframe (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength to front of subframe (5.3.6 (a) (i)) | 1 |
| Offside Rear Braking system leaking brake caliper area |3.6.A.1| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing holed |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced X2 |7.1.1 |a| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch near chassis |6.2.2 |d| |i|| | 1 |
| Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both sills (6.1.1 (c) (i)) | 1 |
| Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both sills (6.1.1 (c) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer rear sill area |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer rear sill area |7.1.1 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mount area |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock mount |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension arm likely to become detached |5.3.3 |a| |ii|| | 1 |
| Nearside Body panel corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Offside Body panel corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Rear Exhaust has a major leak of exhaust gases Back box > mid section joint |7.1.2| | 1 |
| Brake pipe connection leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) | 1 |
| Offside Rear coil spring inappropriately repaired |2.4.A.2| | 1 |
| Suspension component mounting prescribed area is excessively corroded both rear complete inner archs |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength box section (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension arm attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Integral body structure has excessive corrosion which adversely affects braking or steering -A- post (6.1.1 (c) (ii)) | 1 |
| Nearside Front Steering linkage ball joint modification unsafe Locking device missing (2.1.3 (f) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Anti-roll bar ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases centre to rear joint |7.1.2| | 1 |
| Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Rear Hydraulic fluid leaking excessively Calliper area. (8.4.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill, welding repair is not a continuous seam weld (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis above anti roll bar mounts |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis above anti roll bar mounts |5.3.6 |a| |i|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill/inner arch (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill/jacking point (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Anti-roll bar linkage has excessive play in a ball joint Outer Drop link |2.4.G.2| | 1 |
| Offside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded Floor |5.2.6| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded Floor |5.2.6| | 1 |
| Nearside Rear Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Nearside Rear Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Nearside Front Outer Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chalked (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Suspension arm fractured |2.4.G.1| | 1 |
| Exhaust has a major leak of exhaust gases centre box |6.1.2 |a|| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded inner arch |2.1.2 |e| |i|| | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength boot floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chasis leg marked with chalk do not cover repair (5.3.6 (a) (i)) | 1 |
| Nearside Power steering pipe|s| or hose|s| leaking from a seal |2.3.3b| | 1 |
| Nearside Front Anti-roll bar has excessive play in a ball joint under load |2.4.G.2| | 1 |
| Nearside Rear Brake cable has restricted free movement hand brake |1.1.15 |e|| | 1 |
| Nearside Rear Seat belt attachment fitting badly deteriorated |5.2.3| | 1 |
| Offside Rear Seat belt attachment fitting badly deteriorated |5.2.3| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded and outer sill |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill and box section |5.2.6| | 1 |
| Rear Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Nearside Front Exhaust catalytic converter missing where one was fitted as standard |7.1.3| | 1 |
| Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan |5.3.6 |a| |i|| | 1 |
| Offside Front rear brake excessively fluctuating |3.7.B.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing area |2.4.A.3| | 1 |
| Rear Stop lamp not working centre |1.2.1b| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner cill corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner cill corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner cill corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pannel were battery is located (5.3.6 (a) (i)) | 1 |
| Brake hose stretched |found during steering lock to lock check| both |2.2.D.2b| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill holed and heavily corroded |5.2.6| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings leg holed and heavily corroded |6.1.B.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases rear silencer not connected |7.1.2| | 1 |
| Nearside Front Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Exhaust has a major leak of exhaust gases centre to rear |6.1.2 |a|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer Sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill (6.2.2 (d) (i)) | 1 |
| Offside Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Offside Front Hydraulic brake cylinder leaking hydraulic fluid caliper (1.1.16 (b) (i)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Chassis leg by coil spring |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Chassis leg by coil spring |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill |6.1.B.2| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed |7.1.1 |a| |i|| | 1 |
| Offside Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing /chasses by anti-roll bar mount |2.4.A.3| | 1 |
| Offside Front Shock absorber has an excessively worn bush bottom bush |2.7.4| | 1 |
| Exhaust has a major leak of exhaust gases rear end of centre section |7.1.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail by anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail by anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced in rear wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Offside Front Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 1 |
| Seat belt anchorage prescribed area is excessively corroded Top of NSR inner wheelarch |5.2.6| | 1 |
| Suspension spring mounting prescribed area is excessively corroded Top of OSR inner wheelarch |2.4.A.3| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength NSF chassis lower face under wheelarch |5.3.6 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced Offside floorpan |7.1.1 |a| |i|| | 1 |
| Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Top of NSR inner wheelarch |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill split (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt buckle missing (7.1.2 (d)) | 1 |
| Offside Front Hydraulic brake calliper insecurely mounted lower bolt missing (1.1.16 (c) (i)) | 1 |
| Rear Vehicle structure inadequately repaired such that structural rigidity is significantly reduced both outer sill (6.1.1 (d) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded wishbone |2.4.A.3| | 1 |
| Brake performance not tested due to n/s/f brake seized (1.2.1 (g)) | 1 |
| Power steering pipe|s| or hose|s| excessively corroded pipe from pump to pinion |2.3.2| | 1 |
| Power steering pipe|s| or hose|s| excessively corroded pipe from pinion to middle of rack body |2.3.2| | 1 |
| Power steering pipe|s| or hose|s| excessively corroded pipe from pinion back to pump |2.3.2| | 1 |
| Power steering pipe|s| or hose|s| excessively corroded PAS oil cooler near NS chassis leg/front pannel |2.3.2| | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill excessively corroded and holed |6.1.B.2| | 1 |
| Emissions not tested engine water pump drive belt missing, risk of engine damage due to lack of coolant circulation if emisions done |7.3.A.1| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Nearside Front Inner Vehicle structure has an inadequate repair which adversely affects braking or steering sill |6.1.A.1| | 1 |
| Offside Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired floor to sill (6.2.2 (d) (ii)) | 1 |
| Emissions not tested failed on lambda recommend an engine clean (8.2.1.2 (d)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is fractured outer sill |2.4.A.3| | 1 |
| Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Upper Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Rear Upper Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner/outer sill. |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is severely distorted |5.2.6| | 1 |
| Nearside Front Outer Subframe mounting prescribed area is excessively corroded Sill corroded. |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Suspension arm and anti roll bar area |2.4.A.3| | 1 |
| Nearside Front Power steering pipe|s| or hose|s| leaking all other pipes badly corroded |2.3.3b| | 1 |
| Nearside Rear Suspension arm inappropriately repaired |2.4.A.2| | 1 |
| Offside Rear Suspension arm inappropriately repaired |2.4.A.2| | 1 |
| Nearside Front Tie bar/rod has excessive play in a pin/bush droplink |2.4.G.2| | 1 |
| Offside Front Tie bar/rod has excessive play in a ball joint droplink |2.4.G.2| | 1 |
| Nearside Rear Tie bar/rod has excessive play in a pin/bush droplink |2.4.G.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded lower wishbone corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded lower wishbone corroded |2.4.A.3| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Exhaust has a major leak of exhaust gases cat to front pipe (6.1.2 (a)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Rear coil spring broken |2.4.C.1a| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Steering column top bearing excessively worn |2.1.2c| | 1 |
| Rear brake binding | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Offside Rear coil spring incomplete |2.4.C.1a| | 1 |
| Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt both |2.1.3 |g| |ii|| | 1 |
| Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt both |5.3.4 |b| |ii|| | 1 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Coil spring fractured or broken |5.3.1 |b| |i|| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
| Nearside Rear coil spring fractured |2.4.C.1a| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Centre Front Horn control missing |1.6.1| | 1 |
| Offside Front Seat belt installation anchorage insecure |10.1 |d|| | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front brake caliper has restricted free movement |3.5.1k| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Emissions not tested due to cat missing (8.2.1.2 (d)) | 1 |
| Road wheel fixings not compatible (5.2.2 (d)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Offside Front Brake pipe connection leaking on a hydraulic braking system in engine bay (1.1.11 (b) (ii)) | 1 |
| Nearside Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor marked yellow (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch marked yellow (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch marked yellow (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch marked yellow (5.3.6 (a) (i)) | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a)) | 1 |
| Nearside Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Shock absorbers has negligible damping effect Front and rear (5.3.2 (d)) | 1 |
| Drivers door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Brake valve leaking (1.1.7 (d) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis Rail (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Front Inner Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
| Nearside Front Lower Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Position lamp not working All (4.2.1 (a) (ii)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis/Floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Nearside Rear Upper Suspension component pin or bush excessively worn on hub (5.3.4 (a) (i)) | 1 |
| Nearside Front Direction indicator light intensity significantly reduced (4.4.3 (a)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced bulk head (7.1.1 (a) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Front Coil spring missing and directional control affected (5.3.1 (c) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills (5.3.6 (a) (i)) | 1 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Main beam tell-tale not working staying on permanant when lights on (4.9.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Headlamp not working on main beam Switch (4.1.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on main beam Switch (4.1.1 (a) (ii)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel area (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel area (7.1.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer (6.1.2 (a)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Subframe mounting prescribed area excessively corroded significantly reducing structural strength Front of Chassis Rail (5.3.6 (a) (i)) | 1 |
| Offside Subframe mounting prescribed area excessively corroded significantly reducing structural strength Front of Chassis Rail (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Speedometer cannot be illuminated (7.8 (c) (ii)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Nearside Front front brake binding (3.7.B.1) | 1 |
| Offside Front front brake binding (3.7.B.1) | 1 |
| Offside Front Direction indicator adversely affected by the operation of another lamp (1.4.A.2h) | 1 |
| Service brake: efficiency below requirements (3.7.B.7) | 1 |
| Nearside Rear brake disc excessively pitted (3.5.1h) | 1 |
| Nearside Rear Shock absorber has a serious fluid leak (2.7.3) | 1 |
| Nearside Rear Shock absorber has negligible damping effect (2.7.5) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Brake hose excessively stretched (1.1.12 (b) (ii)) | 1 |
| Offside Rear Brake hose excessively stretched (1.1.12 (b) (ii)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak silencer (8.2.1.1 (b)) | 1 |
| Emissions unable to be completed Exhaust leak (8.2.2.2 (e)) | 1 |
| Central Emission control equipment missing where fitted as standard exhaust heat sensor (8.2.2.1 (a)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Central Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor section (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect both sides (4.1.2 (c)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Position lamp not working Side light. (4.2.1 (a) (ii)) | 1 |
| Offside Front Position lamp not working Side light. (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Position lamp not working Side light. (4.2.1 (a) (ii)) | 1 |
| Offside Rear Position lamp not working Side light. (4.2.1 (a) (ii)) | 1 |
| Nearside Front Lower Body panel insecure Wing. (6.2.1 (a) (i)) | 1 |
| Offside Front Lower Body panel insecure Wing. (6.2.1 (a) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 1 |
| Front Drivers airbag missing Aftermarket steering wheel fitted with no airbag (7.1.5 (a)) | 1 |
| Offside Front Hydraulic brake calliper leaking banjo bolt joint to brake hose was leaking (tightened and rechecked all ok at time of test ) (1.1.16 (b) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Body sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor pan by subframe mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Fuel tank leaking (6.1.3 (b) (i)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Upper Steering column universal joint insecure Loose pinch bolt. (2.1.3 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Nearside Front Upper Steering locking device missing ball joint split pin missing. (2.1.3 (d)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill to inner wing. (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill. (7.1.1 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases down pipe broken (6.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill/Arch (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outersill small hole (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed (8.2.1.2 (d)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Headlamp not working on dipped beam Both sides (4.1.1 (a) (ii)) | 1 |
| Headlamp not working on main beam Both sides (4.1.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Central Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 1 |
| Nearside Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Power steering inoperative belt is worn (2.1.5 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill as marked (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner structural panel ( internal part of shell ) (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill as marked (6.1.1 (c) (i)) | 1 |
| Front Bumper insecure not attached at any of lower or side mounting points (both sides) (6.1.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt ball joint (5.3.4 (b) (ii)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements tell tail inoperative (4.5.3 (a)) | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill area (6.1.1 (c) (i)) | 1 |
| Nearside Stop lamp(s) remains on when the brakes are released (4.3.2 (a) (iii)) | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Offside Headlamp are incorrectly positioned (4.1.4 (a)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Middle (6.1.1 (c) (i)) | 1 |
| Offside Headlamp aim unable to be tested due to dip beam not working (4.1.2 (b)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect dips right (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect dips righr (4.1.2 (c)) | 1 |
| Nearside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor to chassis (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill in several places |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail by sub-frame mount |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength end of sill/inner flitch |5.3.6 |a| |i|| | 1 |
| Emissions not tested as no gases present at rear tailpipe (8.2.1.2 (d)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury outer sill and inner stucture |6.2.1 |a| |i|| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Front Body component insecure wing (6.2.1 (a) (i)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak silencer joint (8.2.1.1 (b)) | 1 |
| Subframe mounting prescribed area is excessively corroded both nearside and offside front chassis rails completely rotten from front subframe mounting points forward to radiator crossmember. anti roll bar barely held on by anything. |2.4.A.3| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis member |5.3.6 |a| |i|| | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis member |5.3.6 |a| |i|| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/wheel arch area (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch sill area (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within 30cm of subframe mounting (5.3.6 (a) (i)) | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced oth rear inner sills and off side rear inner wheel arch and outer sill (7.1.1 (a) (i)) | 1 |
| Offside Headlamp not working on dipped beam intermittent (4.1.1 (a) (ii)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Parking brake lever releases when knocked |3.1.6a| | 1 |
| Exhaust has a major leak of exhaust gases Middle box to rear box joint leaking effecting emissions (6.1.2 (a)) | 1 |
| Nearside Front Road wheel spoke bent |4.2.A.1b| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and floor (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill and floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill and floor (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases joint at rear box (6.1.2 (a)) | 1 |
| Emissions not tested major leak at rear (8.2.1.2 (d)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg holed |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg holed |6.1.B.2| | 1 |
| Nearside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting inner arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer cill (6.2.2 (d) (i)) | 1 |
| Offside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting inner arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded split (7.1.1 (a) (i)) | 1 |
| Nearside Front Road wheel spigot mounting excessively worn (5.2.2 (c) (i)) | 1 |
| Nearside Front Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is inadequately repaired outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Track rod end ball joint worn to the extent there is a serious risk of detachment |2.1.3 |b| |ii|| | 1 |
| Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced and outer wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis to front cross member as marked |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill as marked |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill as marked |6.1.B.2| | 1 |
| Nearside Front Front position lamp|s| not working replaced 501 capless bulb |1.1.A.3b| | 1 |
| Offside Front Front position lamp|s| not working replaced 501 capless bulb |1.1.A.3b| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Front Power steering pipe/hose excessively corroded (2.1.5 (g) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear box and middle section |6.1.2 |a|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing / chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Offside Body has a sharp edge caused by damage door mirror housing |6.1.C.1| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded bodysill |2.4.A.3| | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak |8.2.2.1 |b|| | 1 |
| Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Rear Position lamp showing white light to the rear |4.2.3 |a| |ii|| | 1 |
| Nearside Rear Position lamp lens seriously defective |4.2.1 |b|| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect bulb fitted incorrect (4.1.2 (c)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Nearside Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction number plate (3.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Coil spring not correctly located |2.4.C.2| | 1 |
| Offside Rear Road wheel badly damaged |4.2.A.1a| | 1 |
| Offside Front Anti-roll bar linkage damaged and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Rear Brake valve leaking caliper (1.1.7 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill backing (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill backing (5.3.6 (a) (i)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases on flange (6.1.2 (a)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced lower front of rear arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced lower front of inner arch (7.1.1 (a) (i)) | 1 |
| Service brake imbalanced across an axle front (1.2.1 (b) (i)) | 1 |
| Offside Front Anti-roll bar linkage insecure drop link detached from lower balljoint. |2.4.G.1| | 1 |
| Nearside Rear Brake inadequately mounted brake calliper |1.1.21 |c|| | 1 |
| Nearside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Emissions unable to be completed exhaust incomplete (8.2.1.2 (d)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill panels |5.2.6| | 1 |
| Brake performance unable to be tested Excessive binding on nsf (1.2.1 (g)) | 1 |
| Emissions unable to be completed Alternator smoking while on fast idle (8.2.1.2 (d)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panels (7.1.1 (a) (i)) | 1 |
| Brake performance unable to be tested Due to brake caliper leaking. (1.2.1 (g)) | 1 |
| Rear Anti-roll bar insecure and fouling on spring |2.4.G.1| | 1 |
| Nearside Rear Suspension weakened allowing body or other component to foul a road wheel or would do so if laden shock has lost its gas |2.4.A.1b| | 1 |
| Centre Obligatory mirror seriously obscured affecting the rear view |8.1.2a| | 1 |
| Exhaust has a major leak of exhaust gases Mid to rear section (6.1.2 (a)) | 1 |
| Nearside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance bulb |1.1.A.3d| | 1 |
| Offside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance bulb |1.1.A.3d| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill panel (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis has major corrosion and holed |6.1.1 |c| |i|| | 1 |
| Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis has major corrosion and holed |6.1.1 |c| |i|| | 1 |
| Offside Front Body panel likely to become detached wing has major corrosion at fixings |6.2.1 |a| |ii|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis |6.2.2 |d| |i|| | 1 |
| Nearside Front Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
| Nearside Front Coil spring with an unsafe modification Coil over fitted suspension too low. |5.3.1 |d| |i|| | 1 |
| Rear Coil spring with an unsafe modification Coil over fitted suspension too low. |5.3.1 |d| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting area. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area. (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area. (7.1.1 (a) (i)) | 1 |
| Front Position lamp light intensity significantly reduced left and right hand, bulbs blackened |4.2.3 |a| |ii|| | 1 |
| Offside Rear Anti-roll bar linkage ball joint likely to become detached Detached from susp. arm |5.3.4 |a| |ii|| | 1 |
| Front Position lamp not working pair |4.2.1 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under anti rollbar (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under rollbar (5.3.6 (a) (i)) | 1 |
| Nearside Rear Parking brake lever has excessive movement indicating incorrect adjustment caliper (1.1.6 (c)) | 1 |
| Rear Exhaust has a major leak of exhaust gases tailpipe to front pipe joint |7.1.2| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill area |6.2.2 |d| |i|| | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill area |6.2.2 |d| |i|| | 1 |
| Nearside Front Lower Suspension arm insecurely attached ball joint split pin missing castellated nut. (5.3.3 (a) (i)) | 1 |
| Offside Front Suspension arm insecurely attached split pin missing from castellated nut (5.3.3 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis corroded (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis corroded (6.1.1 (c) (i)) | 1 |
| Offside Front Upper Suspension arm pin or bush likely to become detached front bush excessively worn (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill/outer sill |7.1.1 |a| |i|| | 1 |
| Front Service brake excessively binding both |1.2.1 |f|| | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Front Position lamp light intensity significantly reduced both |4.2.3 |a| |ii|| | 1 |
| Centre Front Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits co 1.420 (8.2.1.2 (c)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill is excessively corroded within 30cm of prescribed area |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill to floorpan |5.2.6| | 1 |
| Offside Outer Rear Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt SPLIT (2.1.3 (g) (ii)) | 1 |
| Offside Front Drivers seat insecure BOLT LOOSE (6.2.5 (a) (ii)) | 1 |
| Nearside Front Lower Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt SPLIT (2.1.3 (g) (ii)) | 1 |
| Offside Front Lower Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt SPLIT (2.1.3 (g) (ii)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill x2 |7.1.1 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Anti-roll bar linkage missing (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar linkage missing (5.3.3 (a) (ii)) | 1 |
| Offside Rear Anti-roll bar linkage missing (5.3.3 (a) (ii)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded O/S outer sill |5.2.6| | 1 |
| Nearside Front rear brake juddering severely |3.7.A.5b| | 1 |
| Offside Front rear brake juddering severely |3.7.A.5b| | 1 |
| Emissions not tested Engine is not running well enough to test (8.2.1.2 (d)) | 1 |
| Rear Coil spring fractured or broken Both (5.3.1 (b) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side not working |1.4.1 |a|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill in 2 places |5.2.6| | 1 |
| Suspension arm corroded and seriously weakened both rear lower wishbones |as marked| |2.4.G.1| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded sill |as marked| |5.2.6| | 1 |
| Nearside Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis near upper arm mount |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded Inner sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner Sill |2.4.A.3| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt both boots on link |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt both boots on link |2.4.G.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner seal/quarter |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced boot floor (7.1.1 (a) (i)) | 1 |
| front brake binding Both |3.7.B.1| | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid CALIPER |3.6.A.1| | 1 |
| Suspension component mounting prescribed area is excessively corroded nearside front chassis on side and underneath |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded offside front chassis on side |2.4.A.3| | 1 |
| Battery insecure and likely to fall from carrier battery floor excessively corroded (4.13 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail within 30cm of suspension mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch |6.1.B.2| | 1 |
| Nearside Seat belt anchorage likely to become detached in the event of a collision rear inner sill and inner wheel arch (7.1.1 (a) (ii)) | 1 |
| Offside Seat belt anchorage likely to become detached in the event of a collision rear inner sill and inner wheel arch (7.1.1 (a) (ii)) | 1 |
| Offside Floor excessively deteriorated os rear floor pan (6.2.4 (a) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced underfloor |6.1.1 |c| |i|| | 1 |
| Nearside Front Lower Suspension component pin or bush excessively worn shock absorber |5.3.4 |a| |i|| | 1 |
| Offside Rear Upper Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Lower Suspension arm has an unsafe modification |5.3.3 |c| |i|| | 1 |
| Offside Front Floor excessively deteriorated next to chassis rail |6.2.4 |a| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill rusted and holed |7.1.1 |a| |i|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill rusted and holed |7.1.1 |a| |i|| | 1 |
| Nearside Steering locking device missing track rod end split pin (2.1.3 (d)) | 1 |
| Offside Steering locking device missing trackrod end split pin (2.1.3 (d)) | 1 |
| Nearside Track rod end ball joint has excessive play nut loose (2.1.3 (b) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded under wing |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded under wing |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis near upper suspension arm (5.3.6 (a) (i)) | 1 |
| Nearside Steering locking device missing track rod end |2.1.3 |d|| | 1 |
| Nearside Front Upper Suspension arm insecurely attached split pin missing |5.3.3 |a| |i|| | 1 |
| Offside Front Upper Suspension arm insecurely attached split pin missing |5.3.3 |a| |i|| | 1 |
| Rear fog lamp tell-tale missing |4.9.1 |a| |ii|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded of outer sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded of outer sill |5.2.6| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure (5.3.3 (a) (i)) | 1 |
| Side repeater missing |1.4.A.2b| | 1 |
| Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Front Brake pipe leaking on a hydraulic braking system Hose to Master cylinder (1.1.11 (b) (ii)) | 1 |
| Nearside Front Lower Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases front pipe to the manifold has 2 nuts missing (6.1.2 (a)) | 1 |
| Headlamp aim unable to be tested Both Sides (4.1.2 (b)) | 1 |
| Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt Both Fronts (5.3.4 (b) (ii)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired inner seal and inner upper wheel arch (6.2.2 (d) (ii)) | 1 |
| Nearside Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint likely to become detached insecure nut loose |5.3.4 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chasis , inner wing area |5.3.6 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded chassis rail |5.2.6| | 1 |
| front brake binding both front brakes |3.7.B.1| | 1 |
| Offside Track rod end seriously misaligned (2.1.3 (e)) | 1 |
| Anti-roll bar missing (5.3.3 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases behind cat
|7.1.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill/wheel arch area |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill/wheel arch area |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis holed (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wing/sill holed (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wing/sill holed (6.2.2 (d) (i)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/floor both sides |6.1.1 |c| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage severely distorted |2.4.G.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded undersill |5.2.6| | 1 |
| Rear Anti-roll bar linkage severely distorted |2.4.G.1| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 1 |
| Braking system leaking OSR CALIPER |3.6.A.1| | 1 |
| Nearside Rear Brake hose excessively twisted (1.1.12 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt drop link ball joint gaiter split (5.3.4 (b) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed & rusted (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed & rusted (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer Sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength above anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength above anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Integral body structure is fractured and structural rigidity is significantly reduced |6.1.1 |a| |i|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak back box |8.2.1.1 |b|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis near anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis near anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction Rear O2 sensor defective (8.2.1.2 (h)) | 1 |
| Emissions not tested due to vehicle hunting and misfiring (8.2.1.2 (d)) | 1 |
| Nearside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Position lamp not working both side (4.2.1 (a) (ii)) | 1 |
| Nearside Front Sub-frame attachment bracket/mounting bolt missing rear bolt |2.4.G.1| | 1 |
| Offside Front Sub-frame attachment bracket/mounting bolt missing rear bolt |2.4.G.1| | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Front All position lamps not working affected by hazard lights . |4.2.1 |a|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill.holed due to corrosion. |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill. (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting And outer sill (6.2.2 (d) (i)) | 1 |
| Offside Headlamp lens seriously defective unable to test beam (4.1.1 (b) (ii)) | 1 |
| Emissions unable to be completed Due to hole in exhaust (8.2.1.2 (d)) | 1 |
| Nearside Headlamp lens seriously defective unable to test beam (4.1.1 (b) (ii)) | 1 |
| Headlamp aim unable to be tested Both sides (4.1.2 (b)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Under arch (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases at join (6.1.2 (a)) | 1 |
| Offside Front Anti-roll bar linkage likely to become detached (5.3.3 (a) (ii)) | 1 |
| Power steering component leaking Steering rack area (2.1.5 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel arch holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting corroded and seriously weakened Mount to chassis (5.3.3 (b) (i)) | 1 |
| Brake performance not tested Leaking caliper (1.2.1 (g)) | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive 0.54 |7.3.D.3| | 1 |
| Rear Exhaust system not adequately supported joint |7.1.1| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor pan (6.1.1 (c) (i)) | 1 |
| Suspension component mounting prescribed area is excessively corroded both rear outer sills |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected bed |5.3.6 |a| |ii|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting in-front of rear wheel for seat belt mounting and seat rails |6.2.2 |d| |i|| | 1 |
| Nearside Front Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Offside Front Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Front position lamp|s| not working both
|1.1.A.3b| | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn drop link |5.3.4 |a| |i|| | 1 |
| Nearside Front Outer Steering linkage ball joint has excessive play |2.1.3 |b| |i|| | 1 |
| Engine MIL inoperative or indicates a malfunction engine management |8.2.1.2 |h|| | 1 |
| Offside Position lamp not working |4.2.1 |a| |ii|| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush drop link |2.4.G.2| | 1 |
| Brake pipe leaking Front to rear |3.6.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded at anti-roll-bar mount point |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired Filler and fibreglass (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired Filler & fibreglass (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill outer (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill inner and outer (7.1.1 (a) (i)) | 1 |
| Offside Brake pipe at imminent risk of failure or fracture (1.1.11 (a)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering outer seal (6.1.1 (c) (ii)) | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering outer seal (6.1.1 (c) (ii)) | 1 |
| Windscreen in such a condition that visibility through swept area is seriously affected |3.2 |c| |ii|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch / sill end (5.3.6 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill, 30cm from passenger seatbelt anchor |6.1.1 |c| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced 30 cm from rear suspension components |6.1.1 |c| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nearside rear sill |7.1.1 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases center box |6.1.2 |a|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting seat belt (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting seat belt (6.2.2 (d) (i)) | 1 |
| Nearside Front Floor excessively deteriorated jacking point (6.2.4 (a) (i)) | 1 |
| Offside Front Floor excessively deteriorated jacking point (6.2.4 (a) (i)) | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill excessively corroded within 30cm of seatbelt anchor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill/floor/ outer sill |6.1.B.2| | 1 |
| Offside Front Outer Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arches incomplete , front to rear of arches, both sides (6.1.1 (c) (i)) | 1 |
| Front Front position lamp|s| has less than 50% of the light sources illuminating head lamps both |1.1.A.3b| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill backing |6.2.2 |d| |i|| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Steering damper leaking oil pipe |2.2.C.1f| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis corroded and holed within 30cm of subframe mounting points |6.1.A.1| | 1 |
| Offside Brake pipe leaking front to rear pipe corroded |3.6.A.1| | 1 |
| Power steering pipe|s| or hose|s| leaking and corroded |2.3.3b| | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced NO PATTERN (4.1.4 (b)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits TOO HIGH (8.2.1.2 (c)) | 1 |
| Central Rear Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Supplementary Restraint System warning lamp indicates a fault flashing |5.4.2| | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength Chassis |5.3.6 |a| |i|| | 1 |
| Nearside Rear Braking system leaking BRAKE PIPE LEAKING FLUID (1.1.3 (d)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor sill (5.3.6 (a) (i)) | 1 |
| Offside Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed |7.1.1 |a| |i|| | 1 |
| Offside Front Anti-roll bar damaged and seriously weakened |5.3.3 |b| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear floor |5.3.6 |a| |i|| | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill. (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rear floor near seat mount (6.2.2 (d) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced excessive corrosion between sill and floor. (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced excessive corrosion between sill and floor. (7.1.1 (a) (i)) | 1 |
| Nearside Front Brake hose excessively stretched Found during steering lock to lock check (1.1.12 (b) (ii)) | 1 |
| Offside Front Brake hose excessively stretched Found during steering lock to lock check (1.1.12 (b) (ii)) | 1 |
| Nearside Service brake excessively binding |1.2.1 |f|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill panel (7.1.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under side (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure inadequately repaired such that structural rigidity is significantly reduced side sill (6.1.1 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill side (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Emissions not tested Exhaust leaking at rear |8.2.1.2 |d|| | 1 |
| Nearside Front All position lamps not working park |1.1.A.3b| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits 1.048 |7.3.D.3| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front floors corroded, within prescribed areas of front suspension mounts (5.3.6 (a) (i)) | 1 |
| Battery insecure and likely to fall from carrier floor corroded beneath (4.13 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength by antiroll bar mounting point (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired outer sill contains excessive body filler |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired outer sill contains excessive body filler |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill in three places |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis 2 places |2.4.A.3| | 1 |
| Offside Rear Lower Radius arm corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch to sill (5.3.6 (a) (i)) | 1 |
| Offside Front Brake rod has restricted free movement (1.1.15 (e)) | 1 |
| Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases silnencer |7.1.2| | 1 |
| Central Exhaust has a major leak of exhaust gases exhaust |7.1.2| | 1 |
| Offside Rear Wheel bearing play so excessive it is likely to break up (5.1.3 (a) (ii)) | 1 |
| Nearside Front Upper Tie bar/rod ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Rear Lower Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Nearside Front Upper Suspension arm locating pin retaining device missing castle nut fitted, no split pin |2.4.G.3b| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded rear inner face sill corroded/holed |5.2.6| | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened hole in arm |2.4.G.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded floor area |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor area and chassis |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor area |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer sill |5.2.6| | 1 |
| Rear fog lamp tell-tale not working poor connection came on after alt test |4.9.1 |a| |ii|| | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sills both sides |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired Outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired Outer sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced central sill edge/floor (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced central sill edge/floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced upper wheel arch under plastic cover. (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced rear most floor and sill edge (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired rear most floor and sill edge spot weld and crack need improving (5.3.6 (a) (i)) | 1 |
| Vehicle structure has damage which adversely affects braking or steering osf inner,lower sill |6.1.A.1| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering nsr inner,lower sill |6.1.A.1| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering osr inner,lower sill |6.1.A.1| | 1 |
| Offside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor area (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill rotted (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill |7.1.1 |a| |i|| | 1 |
| Offside Outer Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch/chassie (5.3.6 (a) (i)) | 1 |
| Brake performance not tested due to suspension arms |3.7.A.1| | 1 |
| Nearside Axle insecure such that stability is impaired Mounting Bush Corroded (5.1.1 (b) (ii)) | 1 |
| Offside Axle insecure such that stability is impaired Mounting Bush Corroded (5.1.1 (b) (ii)) | 1 |
| Nearside Rear Upper Suspension arm attachment bracket/mounting likely to fail |5.3.3 |b| |ii|| | 1 |
| Offside Rear Upper Suspension arm attachment bracket/mounting likely to fail |5.3.3 |b| |ii|| | 1 |
| Offside Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Suspension component mounting prescribed area is excessively corroded chassis rail |viewed from underneath| |2.4.A.3| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced lower chassis rail, near anti roll bar mounting |6.1.1 |c| |i|| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner floor section |6.1.1 |c| |i|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch |6.1.1 |c| |i|| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail, inside inner wheel arch |6.1.1 |c| |i|| | 1 |
| Front Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced lower chassis rail near anti roll bar mounting |6.1.1 |c| |i|| | 1 |
| Brake pipe at imminent risk of failure or fracture rigid brake pipe across rear axel (1.1.11 (a)) | 1 |
| Brake pipe leaking on a hydraulic braking system nearside and offside of rigid brake pipe across axel (1.1.11 (b) (ii)) | 1 |
| Rear Brake lever has insufficient reserve travel |1.1.2 |a|| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill rear end area corroded and hold |7.1.1 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn Loose (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension arm locating pin insecure |2.4.G.3a| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under car sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under car sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under car sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced under car sill as marked (7.1.1 (a) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases at rear (6.1.2 (a)) | 1 |
| Nearside Front Position lamp not working and offside front (4.2.1 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn and offside front d bushes (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Wheel nut|s| missing single nut |4.2.A.1e| | 1 |
| Offside Rear Body has a projection caused by damage |6.1.C.1| | 1 |
| Centre Rear Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Rear Exhaust has a major leak of exhaust gases rear box joint (6.1.2 (a)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassie |5.3.6 |a| |i|| | 1 |
| Offside Front Lower Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Body panel insecure wing (6.2.1 (a) (i)) | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings rear outer sill |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings rear outer sill |6.1.B.2| | 1 |
| Exhaust has a major leak of exhaust gases rear box joint. |6.1.2 |a|| | 1 |
| Offside Brake linkage has restricted free movement handbrake (1.1.15 (e)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill holed within 30 cms (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill holed within 30 cms (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill/floor within 30 cms (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis above roll bar area |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis above roll bar area |6.1.1 |c| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill area (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced lower wheel arch |6.1.1 |c| |i|| | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturer`s specified limits lambda too high |8.2.1.2 |b|| | 1 |
| Nearside Rear Body panel corroded and likely to cause injury wheel arch jagged edge (6.2.1 (a) (i)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury wheel arch jagged edge (6.2.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wing (5.3.6 (a) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side low reading (1.4.1 (a)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer sill |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis leg |6.2.2 |d| |i|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis leg |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting engine bay above chassis leg |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Nearside rear brake recording little or no effort foot & handbrake |3.7.B.5a| | 1 |
| Offside Rear Braking system leaking brake fluid leak |3.6.A.1| | 1 |
| Front front brake binding o/s & n/s |3.7.B.1| | 1 |
| Front position lamp|s| not working off front |1.1.A.3b| | 1 |
| Seat belt anchorage prescribed area is excessively corroded off rear outer sill |5.2.6| | 1 |
| Central Exhaust has a major leak of exhaust gases PIPE (6.1.2 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired outer rear sill not welded continuously (7.1.1 (a) (i)) | 1 |
| Brake pipe leaking on a hydraulic braking system front to rear brake pipe (1.1.11 (b) (ii)) | 1 |
| Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt Nearside and offside (2.1.3 (g) (ii)) | 1 |
| Offside Front Lower Shock absorbers has an excessively worn bush rubber bush |5.3.2 |c|| | 1 |
| Exhaust has a major leak of exhaust gases joints (6.1.2 (a)) | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer body sill |6.1.B.2| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis beam (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer door sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Floor. |5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases Flange |7.1.2| | 1 |
| Electrical wiring insecure hid headlamp wiring |1.9.2a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail by upper suspension arm |2.4.A.3| | 1 |
| Offside Front Lower Suspension arm locating pin insecure front bolt loose |2.4.G.3a| | 1 |
| Rear Brake lining|s| insecure |3.5.1g| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced 1/4 sill to floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced 1/4 sill to floor (6.1.1 (c) (i)) | 1 |
| Nearside Front Direction indicator not working side repeater (4.4.1 (a) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Near side front inner wing (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Off side front inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Statutory seat belt missing catch |5.1.1| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced near anti roll bar d bush (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced near anti roll bar d bush (6.1.1 (c) (i)) | 1 |
| Body panel insecure o/s + n/s outer cills back end (6.2.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis inner wing side and engine side (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis inner wing side (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill separated. (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength wing |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected under sill (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected 2 places under sill (5.3.6 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis by anti roll bar mounting and subframe mounting |5.3.6 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded antiroll bar |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded antiroll bar |2.4.A.3| | 1 |
| Front Supplementary Restraint System warning lamp indicates a fault |5.4.2| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill to arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Wheel arch chassis rail |6.1.B.2| | 1 |
| Nearside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Front Position lamp not working both nearside and offside |4.2.1 |a|| | 1 |
| Nearside Front position lamp|s| not working 501 bulb |1.1.A.3b| | 1 |
| Centre Stop lamp not working 380 bulb |1.2.1b| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Position lamp not working BOTH FRONT (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area fractured significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner leg (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner leg (6.1.1 (c) (ii)) | 1 |
| Offside Outer Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits co is 0.54 limit is 0.30 (8.2.1.2 (a)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch chassis leg |2.4.A.3| | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak joint between ecnter pipe and back box |8.2.1.1 |b|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak back box broken off (8.2.1.1 (b)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner acrh floor (6.1.1 (c) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded SILL |2.4.A.3| | 1 |
| Nearside Front Outer Seat belt anchorage loose |7.1.1 |b|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chasis (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp aim beam image kick up to the offside (1.8) | 1 |
| Offside Headlamp aim beam image kick up to the offside (1.8) | 1 |
| Offside Rear fog lamp missing (1.3.2a) | 1 |
| Rear Exhaust has a major leak of exhaust gases blowing from join to back box, welded together |7.1.2| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced hole in seal |7.1.1 |a| |i|| | 1 |
| Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Both sides sills (Marked in yellow chalk) (6.2.2 (d) (i)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits due to exhaust condition |8.2.1.2 |c|| | 1 |
| Front Anti-roll bar linkage ball joint excessively worn both |5.3.4 |a| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint likely to become detached has become detached (5.3.4 (a) (ii)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded offside mid & rear outer sill |5.2.6| | 1 |
| Suspension component mounting prescribed area is excessively corroded offside front chassis leg in wheel arch |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded nearside front inner wheel arch |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner/outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Seal (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Seal (6.2.2 (d) (i)) | 1 |
| Drivers airbag missing Non original steering wheel fitted (7.1.5 (a)) | 1 |
| Exhaust has a major leak of exhaust gases Centre pipe (6.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Seal (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL |6.1.B.2| | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt retracting mechanism defective slow to retract |7.1.2 |e|| | 1 |
| Offside Front Seat belt retracting mechanism defective belt slow to retract |7.1.2 |e|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill and outer sill joint (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed co an hc high (8.2.1.2 (d)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer door sill |5.2.6| | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting corroded and seriously weakened shock mount marked yellow (5.3.3 (b) (i)) | 1 |
| Offside Front Lower Suspension arm attachment bracket/mounting corroded and seriously weakened shock mount marked yellow (5.3.3 (b) (i)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill marked yellow (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer arch marked yellow (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Adjacent to anti roll bar bracket |5.3.6 |a| |i|| | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Rear outer sill |7.1.1 |a| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg |6.1.1 |c| |i|| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
| Rear Seat belt anchorage prescribed area is excessively corroded both outer sills corroded |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Under sill excessively corroded/holed (7.1.1 (a) (i)) | 1 |
| Sub-frame attachment bracket/mounting missing n/s/f and o/s/f (5.3.3 (a) (ii)) | 1 |
| Nearside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis beam |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill panel |2.4.A.3| | 1 |
| Offside Rear Fuel hose leaking |7.2.3| | 1 |
| Rear Body panel corroded and likely to cause injury wheel arch |6.2.1 |a| |i|| | 1 |
| Nearside Outer Body panel corroded and likely to cause injury sill |6.2.1 |a| |i|| | 1 |
| Offside Outer Body panel corroded and likely to cause injury sill |6.2.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg holed |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Central outer sill section (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Both side (sill) (6.1.1 (c) (i)) | 1 |
| Nearside Front Driver`s view of an obligatory external mirror materially affected by an obstruction |3.1 |a| |ii|| | 1 |
| Offside Front Driver`s view of an obligatory external mirror materially affected by an obstruction |3.1 |a| |ii|| | 1 |
| Nearside Direction indicator not working repeater |4.4.1 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis x3 |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis x2 |5.3.6 |a| |i|| | 1 |
| Nearside Front Body component insecure wing |6.2.1 |a| |i|| | 1 |
| Offside Front Body component insecure wing |6.2.1 |a| |i|| | 1 |
| Front Bumper insecure |6.1.4 |a| |i|| | 1 |
| Offside Rear Floor excessively deteriorated under battery |6.2.4 |a| |i|| | 1 |
| Offside Rear rear brake recording little or no effort park brake |3.7.B.5a| | 1 |
| Rear Parking |secondary brake| on a single line braking system has no recorded effort at a wheel |1.3.1 |a| |ii|| | 1 |
| Centre Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced from front suspension to front bumper mount |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced from front suspension to front bumper mount |6.1.1 |c| |i|| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill |6.1.1 |c| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear outer sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill |7.1.1 |a| |i|| | 1 |
| Offside Front Macpherson strut corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Front Position lamp not working BOTH NS & OS (4.2.1 (a) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Rear Sub-frame pin or bush excessively worn NS & OS Rear subframe/axle bushes corroded (5.3.4 (a) (i)) | 1 |
| Offside Rear Braking system leaking Calliper |3.6.A.1| | 1 |
| Offside Front Suspension arm fractured (5.3.3 (b) (ii)) | 1 |
| Offside Parking brake inoperative on one side & nearside very low effort (1.4.1 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis rail above anti roll bar mounting |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis rail above anti roll bar mounting |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Centre to rear outer sill |5.2.6| | 1 |
| Nearside front parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill, holed through corrosion (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is inadequately repaired both outersills (7.1.1 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength box section (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis front inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor to sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis front inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor adjoining sill holed (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor adjoining sill holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor adjoining sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor adjoining sill holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch excessively corroded and holed (6.2.2 (d) (i)) | 1 |
| Rear Brake lever has abnormal movement of levers indicating excessive wear or maladjustment (1.1.15 (f)) | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under sill area |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under sill area |7.1.1 |a| |i|| | 1 |
| Electrical wiring insecure earth strap going to bottom of rear subframe is broken & detached |1.9.2a| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded under sill area |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg adjacent to anti-roll bar mounts (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 1 |
| Offside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings outer door sill |6.1.B.2| | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid brake caliper |3.6.A.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer seal |5.2.6| | 1 |
| Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced o/s/f floor corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Front Brake pipe leaking on a hydraulic braking system to rear (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill |5.3.6 |a| |i|| | 1 |
| Nearside Headlamp light source and lamp not compatible LED (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible LED (4.1.4 (c)) | 1 |
| Emissions not tested exhaust has major gas leak |7.3.A.1| | 1 |
| Nearside Power steering ram|s| leaking from a failed seal n/s steering rack leeking |2.3.3b| | 1 |
| Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Electrical wiring damaged and bare wires exposed |1.9.2c| | 1 |
| Bonnet cannot be secured in the closed position |3.1 |b| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage damaged and seriously weakened antiroll bar link rod broken |2.4.G.1| | 1 |
| Offside All direction indicators not working |4.4.1 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired chassis in engine bay (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outersill (7.1.1 (a) (i)) | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to sill |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area is excessively corroded near side inner and outer sill |5.2.6| | 1 |
| Offside Front Upper Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Lower Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded rear floor |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg by anti roll bar mount |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg by anti roll bar mount |2.4.A.3| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Next to battery (6.1.1 (c) (i)) | 1 |
| Headlamp not working on dipped beam os |1.7.5a| | 1 |
| All position lamps not working ns |1.1.A.3b| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings os front chassi |6.1.B.2| | 1 |
| brake disc in such a condition that it is seriously weakened front |3.5.1i| | 1 |
| brake disc in such a condition that it is seriously weakened rear |3.5.1i| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front chassis various places |5.3.6 |a| |i|| | 1 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL |6.1.B.2| | 1 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL
|6.1.B.2| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced pocket (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced pocket battery carrier (6.1.1 (c) (i)) | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings antiroll bar mounting |6.1.B.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected outer sill (5.3.6 (a) (ii)) | 1 |
| Central Brake lever has insufficient reserve travel no reserve travel at all |1.1.2 |a|| | 1 |
| Brake performance not tested all 4 wheels locked up |1.2.1 |g|| | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength boot floor (5.3.6 (a) (i)) | 1 |
| Brake performance not tested due to offside rear wish done fractured (1.2.1 (g)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill area (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired inner sill area (7.1.1 (a) (i)) | 1 |
| Nearside Front Brake hose connection leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill x 2 places (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner end of sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition silencer missing |7.1.4| | 1 |
| Rear Electrical wiring insecure earth lead to axle |1.9.2a| | 1 |
| Nearside Front Bumper insecure |6.1.4 |a| |i|| | 1 |
| Rear Sub-frame corroded and seriously weakened mounts offside & nearside |2.4.G.1| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL |5.3.6 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases centre to rear joint (6.1.2 (a)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced cill to floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced cill to floor (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced upper inner wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced upper inner wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis |6.1.1 |c| |i|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill end (6.1.1 (c) (i)) | 1 |
| Brake cable has restricted free movement (3.5.1k) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor inner arch area (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Headlamps matched pair incorrect colour |4.1.4 |a|| | 1 |
| Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arches both sides |5.3.6 |a| |i|| | 1 |
| Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sills both sides |7.1.1 |a| |i|| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner & outer sill |6.1.B.2| | 1 |
| front brake binding nearside & offside |3.7.B.1| | 1 |
| Coil spring fractured or broken Both N/S/R and O/S/R |5.3.1 |b| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both rear outer sills (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill to wheel arch |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside wheel arch on chassis rail (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside wheel arch on chassis rail (5.3.6 (a) (i)) | 1 |
| Offside Rear Stop lamp(s) not working high level (4.3.1 (a) (ii)) | 1 |
| Offside Direction indicator incorrect colour side repeater |4.4.3 |a|| | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt gaiter split (2.1.3 (g) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassy (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arc (5.3.6 (a) (i)) | 1 |
| Offside All direction indicators not working Indicator stalk faulty (4.4.1 (a) (ii)) | 1 |
| Brake performance unable to be tested No pedal pressure (1.2.1 (g)) | 1 |
| coil spring broken both rear |2.4.C.1a| | 1 |
| Rear Exhaust silencer insecure missing |8.1.1 |b| |i|| | 1 |
| Rear Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition silencer missing |8.1.1 |a|| | 1 |
| Nearside Front Vehicle structure is fractured and structural rigidity is significantly reduced chassis |6.1.1 |a| |i|| | 1 |
| Nearside Rear Sub-frame pin or bush likely to become detached |5.3.4 |a| |ii|| | 1 |
| Offside Rear Sub-frame pin or bush likely to become detached |5.3.4 |a| |ii|| | 1 |
| Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Nearside Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill has 1 hole |6.1.B.2| | 1 |
| Driver`s airbag obviously inoperative |7.1.5 |c|| | 1 |
| Windscreen damaged and affecting the driver`s view of the road zone `b` |3.2 |a| |ii|| | 1 |
| Headlamp levelling device inoperative internal |4.1.5 |a|| | 1 |
| Emissions not tested boiled over |8.2.1.2 |d|| | 1 |
| Nearside Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
| Central Exhaust emissions likely to be affected by an exhaust leak exhaust split at joint (8.2.2.1 (b)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected outer sill |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill |5.3.6 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner arch |5.3.6 |a| |ii|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner arch |5.3.6 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner arch |5.3.6 |a| |ii|| | 1 |
| Nearside Rear Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting insecure rear subframe mounting bracket corroded and breaking up (5.3.3 (a) (i)) | 1 |
| Offside Rear Sub-frame attachment bracket/mounting insecure rear subframe mounting bracket corroded and breaking up (5.3.3 (a) (i)) | 1 |
| Emissions not tested emissions not tested due to exhaust blow (8.2.1.2 (d)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced boot area under battery (6.1.1 (c) (i)) | 1 |
| Brake lever has insufficient reserve travel handbrake lever has insufficient reserve travel. (1.1.2 (a)) | 1 |
| Offside Rear Service brake excessively binding osr brake binding. (1.2.1 (f)) | 1 |
| Nearside Front Body panel insecure FRONT PANEL (6.2.1 (a) (i)) | 1 |
| Nearside Front Body component insecure (6.2.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced end of chassis (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill outer holed (6.1.1 (c) (i)) | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced centre sill hole and corroded |6.1.1 |c| |i|| | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill hole and corroded |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor hole and corroded |6.1.1 |c| |i|| | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt lower ball joint dust cover split |5.3.4 |b| |ii|| | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt lower ball joint dust cover split |5.3.4 |b| |ii|| | 1 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases mid section (6.1.2 (a)) | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive + hc |7.3.D.3| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area |7.1.1 |a| |i|| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill area holed and corroded |7.1.1 |a| |i|| | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis holed and corroded under drivers foot area |5.3.6 |a| |i|| | 1 |
| Suspension component mounting prescribed area is excessively corroded n/s and o/s rear outer sill area |2.4.A.3| | 1 |
| Rear rear brake recording little or no effort n/s and o/s |3.7.B.5a| | 1 |
| Rear Brake slack adjuster incorrectly adjusted |1.1.18 |a|| | 1 |
| Front front brake binding x 2 |3.7.B.1| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sills (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner wheel arch (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner wheel arch (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Central Brake pipe at imminent risk of failure or fracture front to rear pipe bursh |1.1.11 |a|| | 1 |
| Nearside Rear Suspension component attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Rear Parking brake efficiency below requirements |3.7.B.7| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ARB D bush bracket area (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ARB D bushes bracket area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch and inner sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired Chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Arch (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor Pan (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Hydraulic fluid leaking excessively Brake Caliper Leaking (8.4.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded at inner wing under wheel arch at anti roll bar mount marked yellow |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded at front inner wing under wheel arch at anti roll bar mounting point marked yellow |2.4.A.3| | 1 |
| Exhaust fumes entering cabin tail pipe missing from rear box (6.1.2 (b) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch by seatbelt mount (6.1.1 (c) (i)) | 1 |
| Nearside Front All position lamps not working nearside sidelamp not working |1.1.A.3b| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak leaking from the front pipe (8.2.1.1 (b)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Outer Sill |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced at inner wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced at rear outer sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting arch sharp edges (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.1 |c| |ii|| | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak silencer bolt snapped causing leak from joint (8.2.2.1 (b)) | 1 |
| Front Suspension component mounting prescribed area is excessively corroded o/s and n/s chassis rails |2.4.A.3| | 1 |
| Front Exhaust has a major leak of exhaust gases around cat flange |7.1.2| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced towing hook to chassis (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced towing hook to chassis (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch by head lamp (6.1.1 (c) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak exhaust section in front of catalytic converter. (8.2.1.1 (b)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Outer Integral body structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced sill (6.1.1 (b) (ii)) | 1 |
| Offside Rear Wheel bearing play so excessive that directional control is impaired (5.1.3 (a) (ii)) | 1 |
| Offside Rear Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Rear Service brake effort inadequate at a wheel Compared to n/s. (1.2.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember mount on chassis (5.3.6 (a) (i)) | 1 |
| Power steering malfunctioning notchy operation (2.1.5 (a)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill and wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill back (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail next to anti roll bar hanger (5.3.6 (a) (i)) | 1 |
| Exhaust silencer insecure |8.1.1 |b| |i|| | 1 |
| Nearside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar bracket |5.3.6 |a| |i|| | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rails both sides (5.3.6 (a) (i)) | 1 |
| Emissions not tested exhaust blow (8.2.1.2 (d)) | 1 |
| Offside Front All position lamps have a product on the lenses so they are not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Front Headlamp lens seriously defective both (4.1.1 (b) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength above anti role bar and near front subframe (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength above anti role bar/ near subframe (5.3.6 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill excessively corroded (6.1.1 (c) (i)) | 1 |
| Front Hydraulic fluid leaking excessively power steering fluid (8.4.1 (a) (i)) | 1 |
| Nearside Front Lower Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Central Exhaust silencer likely to become detached section breaking away from rear flange to the rear silencer. (8.1.1 (b) (ii)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits reading on test 1.20 (8.2.1.2 (c)) | 1 |
| Offside Rear fog lamp not working also tell-tail not working (4.5.1 (a) (ii)) | 1 |
| Headlamp levelling device inoperative inside the vehicle (4.1.5 (a)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced door sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Brake performance not tested caliper leakin bad (1.2.1 (g)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is fractured sill torn/holed |5.2.6| | 1 |
| Rear Seat belt anchorage prescribed area is excessively corroded both |5.2.6| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion around rear cill |7.1.1 |a| |i|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced corroded on outer cill |7.1.1 |a| |i|| | 1 |
| Front Front position lamp|s| not working both front |1.1.A.3b| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Rear of the sill. |6.1.B.2| | 1 |
| Offside Front Suspension arm corroded and seriously weakened lower shock mount (on lower arm) (5.3.3 (b) (i)) | 1 |
| Hazard warning switch inoperative doesnt switch off when desired every time .Remains on with warning lamps on dash and outside vehicle still opperating (4.4.2 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded roll bar mounting |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded roll bar mounting |2.4.A.3| | 1 |
| Engine MIL inoperative or indicates a malfunction Came on during emissions test (8.2.1.2 (h)) | 1 |
| Offside Rear Brake disc fractured (1.1.14 (a) (ii)) | 1 |
| Nearside Front Seat belt not functioning as intended jammed (7.1.2 (c)) | 1 |
| Emissions not tested Serious exhaust leak - no fumes out of tailpipe (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Side and underneath of chassis leg - 2 places (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Side and underneath of chassis leg - 2 places (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis under bonnet |2.4.A.3| | 1 |
| brake disc in such a condition that it is seriously weakened all |3.5.1i| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front inner wings (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both rear under lower sills (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both rear under lower sills (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both rear inner wings (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch |6.1.1 |c| |i|| | 1 |
| Offside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Electrical wiring likely to touch hot or rotating parts lambda sensor wires fouling on prop shaft and exhaust ..re routed behind heat shield (4.11 (a) (iii)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill as marked (previous repair ) (6.1.1 (c) (i)) | 1 |
| Brake pedal creeps with the vacuum fully depleted |3.3.C.2| | 1 |
| Offside Rear Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 1 |
| Nearside Rear Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill holed (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength seal |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength main chassis where anti roll bar mounted (5.3.6 (a) (i)) | 1 |
| Front Anti-roll bar has excessive play in a ball joint both front |2.4.G.2| | 1 |
| Rear Anti-roll bar has excessive play in a ball joint both rear |2.4.G.2| | 1 |
| Offside Front Lower Suspension component ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis legs antiroll bar fixings |5.3.6 |a| |i|| | 1 |
| Central Stop lamp not working not bulb |1.2.1b| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front chassis legs |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail, anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases centre join (6.1.2 (a)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill, |5.2.6| | 1 |
| Offside Front Outer Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corroded and holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg corroded and holed (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened arm |2.4.G.1| | 1 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened arm |2.4.G.1| | 1 |
| Nearside Front Inner Suspension component corroded and seriously weakened Wheel arch next to anti roll bar mounting (5.3.3 (b) (i)) | 1 |
| Nearside Front Inner Suspension component corroded and seriously weakened wheel arch next to anti roll bar mounting (5.3.3 (b) (i)) | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded both inner sill area |2.4.A.3| | 1 |
| Nearside Outer Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail / anti roll bar mount |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis rail / anti roll bar mount |2.4.A.3| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting rivet missing Drop-link |2.4.G.1| | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s rear sill (6.2.2 (d) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting n/s rear sill (6.2.2 (d) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s rear inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Lower Shock absorber insecure nut missing |2.7.2b| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s front chassis to anti roll bar mounting |6.1.B.2| | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor (6.1.1 (c) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced battery tray (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner/ outer sill holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced rear wheel arch holed (7.1.1 (a) (i)) | 1 |
| Front Bumper damaged and likely to cause injury when grazed or contacted including number plate carrier (6.1.4 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases backbox |6.1.2 |a|| | 1 |
| Offside Front Hydraulic brake calliper cracked and braking performance affected o/s/f brake calliper seized (1.1.16 (a) (ii)) | 1 |
| Nearside Front Hydraulic brake calliper cracked and braking performance affected brake caliper seized (1.1.16 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases centre pipe to rear silencer joint (6.1.2 (a)) | 1 |
| Offside Front Position lamp not working not working |4.2.1 |a|| | 1 |
| Offside Front Body has a sharp edge caused by corrosion wing |6.1.C.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases centre section flange (6.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Battery tray (5.3.6 (a) (i)) | 1 |
| Emissions not tested unable to get vehicle to idle. |7.3.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis Rail (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Excessively corroded inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Excessively corroded inner sill (7.1.1 (a) (i)) | 1 |
| Offside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Body component damaged and likely to cause injury rear spoiler (6.2.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis next to subframe mounting and anti roll bar bracket (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis next to anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded body sill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded forward chassis rail |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded forward chassis rail |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area is excessively corroded offside rear inner sill holed |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nearside rear inner sill holed |5.2.6| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Coil spring fractured or broken upper coil (5.3.1 (b) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded lower side sill |5.2.6| | 1 |
| Nearside Front Steering locking device missing bottom ball joint bolt does not extend through the nylock on the nut, needs a longer bolt (2.1.3 (d)) | 1 |
| Offside Front Steering locking device ineffective bottom ball joint bolt does not extend through the nylock on the nut, needs a longer bolt (2.1.3 (d)) | 1 |
| Nearside Front Steering locking device missing track rod end locking device missing (2.1.3 (d)) | 1 |
| Nearside Front Upper Steering locking device missing arm to ball joint missing split pin and bolt too short (2.1.3 (d)) | 1 |
| Offside Front Steering locking device ineffective upper steering arm to ball joint (2.1.3 (d)) | 1 |
| Offside Front Outer Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Inner Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mount area (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mount area (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Power steering malfunctioning |2.1.5 |a|| | 1 |
| Offside Side repeater lens defective such that the emitted light is adversely affected (4.4.1 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing by the jacking point |5.3.6 |a| |i|| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis box section holed by front anti roll bar mounting |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis holed by front anti roll bar mounting |6.1.B.2| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting under sill to floor holed (6.2.2 (d) (i)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt insecure (2.1.3 (g) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis holed |6.1.B.2| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting under sill holed (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sil (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sil (5.3.6 (a) (i)) | 1 |
| Hydraulic fluid leaking continuously posing a serious risk to road safety |8.4.1 |a| |ii|| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded @ anti roll bar mount |2.4.A.3| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded Sill area. |chalked| |5.2.6| | 1 |
| Centre Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis hold |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis hold |2.4.A.3| | 1 |
| Offside Rear Inner Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded side sill |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded side sill |5.2.6| | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Sill Corroded |5.3.6 |a| |i|| | 1 |
| Offside Rear Upper Brake pipe at imminent risk of failure or fracture (1.1.11 (a)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill/floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded body sill area |5.2.6| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded body sill area |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch area and outer body sill area |5.2.6| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis (5.3.6 (a) (ii)) | 1 |
| Offside Front Subframe mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected chassis (5.3.6 (a) (ii)) | 1 |
| Nearside Front Upper coil spring broken |2.4.C.1a| | 1 |
| Nearside Headlamp light intensity severely reduced no pattern requires polishing (4.1.4 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded OSF chassis rail |2.4.A.3| | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s and n/s outer sill (5.3.6 (a) (i)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced o/s and n/s chassis by Anti roll bar mount (6.1.1 (c) (i)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s and n/s inner sills and inner arches (5.3.6 (a) (i)) | 1 |
| Emissions not tested due to car unable to idle (8.2.1.2 (d)) | 1 |
| Offside Front Lower Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded under wheel arch |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded under sill |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired floor to sill (7.1.1 (a) (i)) | 1 |
| Central Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings UNDER THE CHASSIS |6.1.B.2| | 1 |
| Central Brake pipe leaking on a hydraulic braking system Floor (1.1.11 (b) (ii)) | 1 |
| Front Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction cross hanging from mirror (3.1 (a) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis near upper arm mounting |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis near upper arm mounting |6.1.1 |c| |i|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front chassis |5.3.6 |a| |i|| | 1 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt BALL JOINT GATOR SPLIT (5.3.4 (b) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced nearside outer sill excessively corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar linkage ball joint likely to become detached Renewed link . (5.3.4 (a) (ii)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis corroded and holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Parking brake lever defective so that it cannot be satisfactorily operated (1.1.6 (d)) | 1 |
| Nearside Front position lamp|s| not working SIDE |1.1.A.3b| | 1 |
| Offside Front position lamp|s| not working SIDE |1.1.A.3b| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch hold |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch hold |5.3.6 |a| |i|| | 1 |
| Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced both sills prescribed area (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Anti-roll bar attachment bracket/mounting damaged and seriously weakened |5.3.3 |b| |i|| | 1 |
| Exhaust has a major leak of exhaust gases back box tail pipe snaped |6.1.2 |a|| | 1 |
| Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill, outer sill and wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired Inner sill, outer sill and wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill, outer sill and wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired Inner sill, outer sill and wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Seat mounting area (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis leg (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis leg (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills x2 holes (7.1.1 (a) (i)) | 1 |
| Nearside Windscreen wiper missing (3.4 (a)) | 1 |
| Nearside Front Cab or chassis has excessive corrosion to the extent that overall security or stability of the cab is impaired outer sill (6.2.2 (d) (ii)) | 1 |
| Nearside Rear Cab or chassis has excessive corrosion to the extent that overall security or stability of the cab is impaired inner sill (6.2.2 (d) (ii)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both sides chassis rails by d bushes (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner lower wheel arch to sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced lower wing (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced lower inner wheel arch to sill (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch under bonnet (6.1.1 (c) (i)) | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper |1.1.16 |b| |i|| | 1 |
| Offside Front Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg x2 (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg inner/outer (6.1.1 (c) (i)) | 1 |
| Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction 9 air fresheners on the rear view mirror |3.1 |a| |ii|| | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s and n/s anti roll bar mounting areas |5.3.6 |a| |i|| | 1 |
| Nearside Inner Front Road wheel distorted |4.2.A.1a| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer rear sill. |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer rear sill. |7.1.1 |a| |i|| | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner /floor pan (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch/wing (5.3.6 (a) (i)) | 1 |
| Offside Rear Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor by battery tray (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner wheel arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL |6.2.2 |d| |i|| | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL |6.2.2 |d| |i|| | 1 |
| Offside Front Suspension arm locating pin locking device missing TOP BALL JOINT |2.4.G.3b| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill corroded and holed |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill corroded and holed |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing flitch near shock absorber |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill closing panel |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill closing panel |7.1.1 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases rear joint badly corroded and leaking |6.1.2 |a|| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing/ chassis leg |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases centre to rear joint corroded away |6.1.2 |a|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced centre floor pan |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wing |7.1.1 |a| |i|| | 1 |
| Offside Front Position lamp lens seriously defective (4.2.1 (b)) | 1 |
| Nearside Rear Position lamp lens seriously defective sharp edge (4.2.1 (b)) | 1 |
| Electrical wiring insecure and in contact with sharp edges under body |4.11 |a| |ii|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill corrosion hole |2.4.A.3| | 1 |
| Nearside Front Lower Shock absorbers insecurely attached (5.3.2 (a) (i)) | 1 |
| Front Anti-roll bar ball joint likely to become detached n/s and o/s (5.3.4 (a) (ii)) | 1 |
| Centre Front Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg at anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg at anti roll bar mounting 2xplaces (5.3.6 (a) (i)) | 1 |
| Offside Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Brake performance not tested Due to leaking rigid brake pipe |1.2.1 |g|| | 1 |
| Nearside Rear Outer Body has a projection caused by corrosion sill |6.1.C.1| | 1 |
| Rear Parking brake lever releases when knocked |3.1.6a| | 1 |
| Nearside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment ***18 clicks*** (1.1.6 (c)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced ***outer sill*** (7.1.1 (a) (i)) | 1 |
| Parking brake lever ratchet mechanism is broken |3.1.5| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch |6.1.B.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill -floor sections (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill-floor sections (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak joint leaking (8.2.1.1 (b)) | 1 |
| Brake performance not tested due to brake pipe |1.2.1 |g|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS SECTION |5.3.6 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded FLOOR UNDER CAR. |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chasis rail bottom and side (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases backbox (6.1.2 (a)) | 1 |
| Rear Exhaust has a major leak of exhaust gases exaust joint |6.1.2 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing|chassis| |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing|chassis| |5.3.6 |a| |i|| | 1 |
| Nearside Front position lamp|s| missing |1.1.A.3a| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch area (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded lower wishbone |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded lower wishbone |2.4.A.3| | 1 |
| Front Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Nearside Front Hydraulic brake calliper inadequately mounted |1.1.16 |c| |i|| | 1 |
| Offside Front Lower Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` air fresheners hanging from mirror |8.3.1e| | 1 |
| Emissions not tested Exhaust blowing (8.2.1.2 (d)) | 1 |
| Offside Front All position lamps light intensity significantly reduced |4.2.3 |a| |ii|| | 1 |
| Offside Front Coil spring fractured or broken coil spring broken |5.3.1 |b| |i|| | 1 |
| Nearside Rear Parking |secondary brake| on a single line braking system has no recorded effort at a wheel Parking brake not working |1.3.1 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Floor excessively deteriorated offside front floor corroded through. |6.2.4 |a| |i|| | 1 |
| Battery insecure and likely to fall from carrier battery tray in boot heavily corroded and battery protruding through hole. |4.13 |a| |ii|| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering near top suspension mounting |6.1.1 |c| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting point. (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Excessive Corrosion To Rear Of OS Sill Within 30cm Of Seatbelt Mounting Point (6.2.2 (d) (i)) | 1 |
| Offside Outer Front Anti-roll bar linkage synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Front Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wing area corroded (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill corroded (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Nearside Front Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |
| Emissions not tested Engine does not idle unable to complete test |7.3.A.1| | 1 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside Obligatory mirror missing (3.3 (a)) | 1 |
| Anti-lock braking system wheel speed sensor missing All sensors (1.6 (c)) | 1 |
| Anti-lock braking system obviously removed (1.6 (f)) | 1 |
| Nearside Headlamp insecure headlight flickering with engine movement (4.1.1 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect no clear definition of image, possibly bulb not seated correctly (4.1.2 (c)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outersill |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases Centre to rear flanges rotted / breaking away (6.1.2 (a)) | 1 |
| Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt both front (5.3.4 (b) (ii)) | 1 |
| Offside Rear Road wheel badly distorted |5.2.2 |c| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at upper mounting point for suspension arm chassis |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at upper suspension arm mounting point chassis |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Wheel nut|s| missing one wheel nut missing on all four wheels |4.2.A.1e| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti rollbar mount |2.4.A.3| | 1 |
| Offside Rear Upper Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Offside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor |6.1.1 |c| |i|| | 1 |
| Track rod end modification unsafe split pin missing (2.1.3 (f) (i)) | 1 |
| Nearside Headlamp aim not tested due to bulb not working (4.1.2 (b)) | 1 |
| Drivers view of the road through the swept area of the windscreen materially affected by an obstruction sun strip running into swept area (3.1 (a) (ii)) | 1 |
| Rear Emissions not tested exhaust has a major leak of gases (8.2.1.2 (d)) | 1 |
| Rear Exhaust has a major leak of exhaust gases at small silencer (6.1.2 (a)) | 1 |
| Front Headlamp light source and lamp not compatible hid lamps fitted (4.1.4 (c)) | 1 |
| Brake pipe at imminent risk of failure or fracture Front to rear (1.1.11 (a)) | 1 |
| Nearside Rear Brake valve leaking such that brake functionality is affected Caliper (1.1.7 (d) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/floor marked yellow (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm insecurely attached (5.3.3 (a) (i)) | 1 |
| Nearside Rear Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Outer Anti-roll bar insecurely attached |5.3.3 |a| |i|| | 1 |
| Nearside Rear Inner Brake disc in such a condition that it is seriously weakened (1.1.14 (a) (ii)) | 1 |
| Offside Rear Inner Brake disc in such a condition that it is seriously weakened (1.1.14 (a) (ii)) | 1 |
| Exhaust system not adequately supported rear silencer clamp missing |7.1.1| | 1 |
| Offside Front front brake binding unable to check the wheel bearing due to this defect |3.7.B.1| | 1 |
| Offside Rear Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Central Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill |7.1.1 |a| |i|| | 1 |
| Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Rear Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill and lower arch corroded (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis in wheel arch within 30 cm of arb mount and suspension arm mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis by anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Nearside Front Power steering pipe|s| or hose|s| leaking from a seal |2.3.3b| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Outter sill |2.4.A.3| | 1 |
| Central Exhaust has a major leak of exhaust gases box corroded |7.1.2| | 1 |
| Nearside Front Front position lamp|s| not working side light bulb inop |1.1.A.3b| | 1 |
| Offside Front All position lamps not working SIDE LIGHT |4.2.1 |a|| | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL |5.3.6 |a| |i|| | 1 |
| Rear Parking brake lever ratchet mechanism is broken |3.1.5| | 1 |
| Nearside Front Upper Anti-roll bar linkage attachment bracket/mounting fractured |5.3.3 |b| |ii|| | 1 |
| Nearside Front Headlamp are incorrectly positioned (4.1.4 (a)) | 1 |
| Offside Brake pipe leaking on a hydraulic braking system front to rear pipe (1.1.11 (b) (ii)) | 1 |
| Offside Front Integral body structure has excessive corrosion which adversely affects braking or steering by anti roll bar mounting (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill as marked (7.1.1 (a) (i)) | 1 |
| Offside Rear Brake pipe leaking on an air braking system to front (1.1.11 (b) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg as marked (5.3.6 (a) (i)) | 1 |
| Emissions not tested due to rear joint broken |7.3.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected floor pan |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected floor pan |5.3.6 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chasis |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chasis |5.3.6 |a| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Under sill holed and corroded (6.1.1 (c) (i)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.05 (8.2.1.2 (c)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer and inner sills excessively corroded |7.1.1 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage missing ARB link arm completely missing |2.4.G.1| | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits 0.61% (8.2.1.2 (b)) | 1 |
| Front Anti-roll bar attachment bracket/mounting insecure bolts missing both sides |5.3.3 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded out sill excessively corroded marked in yellow |5.2.6| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill rotten (7.1.1 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill rotten (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill
marked with yellow crayon (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill
marked with yellow crayon (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength rear of wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn drop link (5.3.4 (a) (i)) | 1 |
| Nearside Front Upper Coil spring fractured or broken |5.3.1 |b| |i|| | 1 |
| Nearside Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nearside floor corroded |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside floor corroded |7.1.1 |a| |i|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength side and underneath of nearside front chassis leg corroded |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner and outer sills |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength holed mount aira (5.3.6 (a) (i)) | 1 |
| Brake fluid warning lamp illuminated fluid low!! |3.6.G.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill panel (5.3.6 (a) (i)) | 1 |
| Nearside Rear Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Offside Front Wheel nut|s| loose all 4 |4.2.A.1e| | 1 |
| Offside Rear Wheel nut|s| loose all 4 |4.2.A.1e| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch area |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded body sill area |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded body sill area |2.4.A.3| | 1 |
| Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis leg around anti roll bar mount |2.4.A.3| | 1 |
| Exhaust silencer insecure (8.1.1 (b) (i)) | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded INNER SILL COMPLETE |2.4.A.3| | 1 |
| Driver`s view of an obligatory external mirror materially affected by an obstruction |3.1 |a| |ii|| | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill marked |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension arm likely to become detached (5.3.3 (a) (ii)) | 1 |
| Braking system leaking osr caliper leak. |3.6.A.1| | 1 |
| Windscreen in such a condition that visibility through swept area is seriously affected Wiper damage (3.2 (c) (ii)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail (6.1.1 (c) (i)) | 1 |
| Offside Rear Body component insecure Wheel arch lining/trim (6.2.1 (a) (i)) | 1 |
| Offside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer/under-sill |5.2.6| | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marked in yellow (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marked in yellow (6.2.2 (d) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor excessively corroded (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis corroded near shock absorber (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced body corroded inner arch (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg marked in yellow (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill marked in yellow (6.1.1 (c) (i)) | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill area |6.1.B.2| | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength lower wing not attached (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill and wheel arch area . (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch within 30cm of seatbelt mount (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor corroded and holed within prescribed area (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner body sill and floor |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner body sill and floor |7.1.1 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill section |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch chassis section |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg |6.1.A.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor pan |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor pan |6.1.B.2| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outert sill panel corroded (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Inner sill (6.2.2 (d) (ii)) | 1 |
| Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Under Battery (6.2.2 (d) (ii)) | 1 |
| Nearside Front Road wheel more than one fixing loose (5.2.1 (a) (ii)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits Leaking exhaust sealed |8.2.1.2 |c|| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill / floor (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill / floor (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Front Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength floor area marked with yellow chalk (5.3.6 (a) (i)) | 1 |
| Offside Position lamp not working new bulb fitted glb 501 |4.2.1 |a|| | 1 |
| Offside Front Electrical wiring insecure and connectors likely to become disconnected ABS wiring insecure to front hub |4.11 |a| |ii|| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corrosion (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corrosion (5.3.6 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill area (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill area (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Brake disc significantly and obviously worn excessively corroded (1.1.14 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner And Outer Sill Excessively Corroded |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner + outer sills (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner. Sill |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired Outer. Sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired Outer. Sill |5.2.6| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sil |2.4.A.3| | 1 |
| Emissions unable to be completed no fuel (8.2.1.2 (d)) | 1 |
| Offside Front Suspension arm likely to fail front bush is worn (5.3.3 (b) (ii)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail near anti roll mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Body has a sharp edge caused by corrosion osr sill |6.1.C.1| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to inner arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor to Sill area holed/corroded at rear of Sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Service brake excessively binding Parking brake not releasing correctly (1.2.1 (f)) | 1 |
| Nearside Front Outer Steering linkage ball joint ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage corroded and seriously weakened (2.4.G.1) | 1 |
| Offside Front Anti-roll bar linkage corroded and seriously weakened (2.4.G.1) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Hydraulic brake cylinder leaking hydraulic fluid offside front (1.1.16 (b) (i)) | 1 |
| Offside Rear Upper Suspension arm likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Braking system leaking caliper area |3.6.A.1| | 1 |
| Exhaust has a major leak of exhaust gases exhaust blowing at back box to mid pipe (6.1.2 (a)) | 1 |
| Emissions not tested exhaust blowing at rear (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis above a/roll bar mounting |2.4.A.3| | 1 |
| Offside Vehicle structure is fractured and structural rigidity is significantly reduced outer sill (6.1.1 (a) (i)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint Ball joint broken/not attached |2.4.G.2| | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt lower arm ball joint (5.3.4 (b) (ii)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt upper arm ball joint (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt upper arm ball joint (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch and sill excessively corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch area excessive corrosion (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings Under carriage |6.1.B.2| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Outer Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Outer Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Outer Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Outer Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor section |6.1.B.2| | 1 |
| Nearside Rear Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 1 |
| Central Front Exhaust emissions likely to be affected by an exhaust leak |8.2.1.1 |b|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill. (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis section at sub frame mount |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail by sub frame mount |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill |5.3.6 |a| |i|| | 1 |
| Rear Electrical wiring damaged, likely to become detached earthing point on rear differential |1.9.2b| | 1 |
| Offside Front Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Suspension component mounting prescribed area is inadequately repaired both outer sills at rear (5.3.6 (a) (i)) | 1 |
| Offside Rear Hydraulic brake calliper damaged sized (1.1.16 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired inner to outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired inner to outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure has a fracture which is likely to adversely affect braking or steering holed and corroded near suspension component (anti roll bar d bush mount) (6.1.1 (a) (ii)) | 1 |
| Offside Front Vehicle structure has a fracture which is likely to adversely affect braking or steering holed and corroded near suspension component (anti roll bar d bush mount) (6.1.1 (a) (ii)) | 1 |
| Offside Outer Body component corroded and likely to cause injury sill (6.2.1 (a) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced O/S/F Inner Wheel Arch Chassis Corroded Through (6.1.1 (c) (i)) | 1 |
| Front Position lamp not working both side (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill (5.2.6) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill (5.2.6) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting hole in sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Braking system leaking (3.6.A.1) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
| Nearside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor pan (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor pan (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting battery tray (6.2.2 (d) (i)) | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2) | 1 |
| Seat belt anchorage prescribed area is excessively corroded Both rear lower outer sills |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded hole in floor next to chassis leg |2.4.A.3| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings marked with yellow chalk |6.1.B.2| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 1 |
| Offside Front Lower Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Nearside Steering linkage insecure to the extent there is excessive movement at the mountings track rod end insecure (2.1.3 (a) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail marked (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect bulb incorrectly fitted |1.8.A.1b| | 1 |
| Offside Rear Stub axle has excessive vertical movement between stub axle and axle beam |2.5.A.1a| | 1 |
| Offside Rear Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-lock braking system wiring excessively damaged (1.6 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper chassis rail (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper chassis rail (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases At rear joint! |6.1.2 |a|| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened front chassis frame (5.3.3 (b) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened front chassis frame (5.3.3 (b) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded outer body sill |5.2.6| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced leg (6.1.1 (c) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded outer sill corroded holed |2.4.A.3| | 1 |
| Sub-frame locating pin retaining device missing both rear pins missing |2.4.G.3b| | 1 |
| Offside Rear Rear reflector missing |1.5.1a| | 1 |
| Front Exhaust has a major leak of exhaust gases front pipe joint blowing |6.1.2 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch/chassis near anti roll bar bush |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch/chassis near anti roll bar bush |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sil |7.1.1 |a| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Brake pipe at imminent risk of failure or fracture Failed on roller brake test (1.1.11 (a)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill, holed by corrosion with 30cm of NSF lower seat belt mounting (7.1.1 (a) (i)) | 1 |
| Nearside Rear Braking system leaking Brake caliper leaking |3.6.A.1| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings boot sill panel |6.1.B.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed |7.1.1 |a| |i|| | 1 |
| Nearside Front Lower Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases Joint before rear silencer (6.1.2 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill / front of wheelarch , marked (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer face of chassis rail , marked (5.3.6 (a) (i)) | 1 |
| Offside Stop lamp|s| showing white light to the rear |4.3.3 |a| |ii|| | 1 |
| Floor excessively deteriorated inner and outer floor / innersils corroded |6.2.4 |a| |i|| | 1 |
| Nearside Rear Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Rear Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Body has a sharp edge caused by damage Body Sill |6.1.C.1| | 1 |
| Offside Rear Braking system leaking brake hose |3.6.A.1| | 1 |
| Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened both |5.3.1 |b| |i|| | 1 |
| Nearside Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/floor (5.3.6 (a) (i)) | 1 |
| Headlamp switch faulty Main beam not working...Intermitant. |1.7.1| | 1 |
| Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Offside Rear Service brake grabbing severely (1.2.1 (c)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill rear end (7.1.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting missing has no location bracket on dee mounting (5.3.3 (a) (ii)) | 1 |
| Offside Rear Coil spring fractured or broken broken |5.3.1 |b| |i|| | 1 |
| Power steering component|s| leaking from a failed joint |2.3.3b| | 1 |
| Offside Front Lower Subframe mounting prescribed area is excessively corroded Front chassis legs corroded and holed, lower face . |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases Tailpipe to rear silencer. |7.1.2| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area is excessively corroded Adjacent to anti roll bar mounting, outer face. |2.4.A.3| | 1 |
| Nearside Rear Braking system leaking caliper
|3.6.A.1| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill area corroded in seatbelt prescribed area |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill end to wheel arch area |5.2.6| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn excessively worn or loose on fixing (5.3.4 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill corroded to hole (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure is fractured and structural rigidity is significantly reduced inner sill corroded to hole (6.1.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure is fractured and structural rigidity is significantly reduced sill end into wheel arch area corroded to hole (6.1.1 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak blowing between cat and centre pipe. (8.2.1.1 (b)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (front) (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (rear) (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor area (7.1.1 (a) (i)) | 1 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded sill holed |2.4.A.3| | 1 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded sill holed |2.4.A.3| | 1 |
| Electronic parking brake warning indicates a malfunction (1.1.6 (e)) | 1 |
| Offside Front Suspension arm ball joint excessively worn Lower ball joint excessive play (5.3.4 (a) (i)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both |1.7.5a| | 1 |
| Nearside Headlamp light intensity severely reduced dip beam (4.1.4 (a)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill / floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near subframe |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill / floor (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill /floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill / floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill / floor (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner And Outer Sill Excessive Corrosion Close To Mounting (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner And Outer Sill Excessive Corrosion Close To Mounting (7.1.1 (a) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner & Outer Sill (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner & Outer Sill (6.1.1 (c) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer to centre |7.1.2| | 1 |
| Offside Rear Body component damaged and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Brake performance not tested leak on rear offside caliper |3.7.A.1| | 1 |
| Offside Windscreen damaged and affecting the driver`s view of the road |3.2 |a| |ii|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded Wheel arch. |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded Wheel arch. |5.2.6| | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area is excessively corroded Wheel arch. |2.4.A.3| | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area is excessively corroded Wheel arch. |2.4.A.3| | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sharp edges (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis and outrigger to sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis and outrigger to sill (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases in various places (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis outrigg holed . |2.4.A.3| | 1 |
| Rear Stop lamp not working centre stop n/w |1.2.1b| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition Blowing |7.1.4| | 1 |
| Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings offside inner sill |6.1.B.2| | 1 |
| Exhaust has a major leak of exhaust gases Centre/rear section |7.1.2| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded seal |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area is excessively corroded N/S/R outer sill |5.2.6| | 1 |
| Front Headlamp light intensity severely reduced both (4.1.4 (a)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer ill |7.1.1 |a| |i|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak from join from middle to rear box |8.2.1.1 |b|| | 1 |
| Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Both side chassis legs (6.2.2 (d) (i)) | 1 |
| Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Both side (6.2.2 (d) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced corroded hole in undersill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced corroded holeon inner sill near rear arch |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced corroded hole on inner sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced corrodedon inner sill near rear arch |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area fractured significantly reducing structural strength on the chassis as marked (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired floor |5.2.6| | 1 |
| Nearside Front suspension has a suspension upper ball joint securing nut not locked nut missing |2.5.B.1a| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel (7.1.1 (a) (i)) | 1 |
| Side repeater incorrect colour both (4.4.3 (a)) | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer seal |6.1.B.2| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing /arch holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced upper inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced upper inner wheel arch (7.1.1 (a) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction p0012 = intake camshaft timing over retarded |8.2.1.2 |h|| | 1 |
| Offside Front Seat belt insecurely fixed to the seat |5.2.1a| | 1 |
| Emissions unable to be completed Obvious exhaust leak (8.2.1.2 (d)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect bulb incorrectly fitted (4.1.2 (c)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak all flanges excessively corroded, blowing from rear silencer join (8.2.2.1 (b)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering under the cover (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering under the cover (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Braking system leaking BRAKE CALIPER HOSE LEAKING FLUID |3.6.A.1| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg in engine bay (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg in engine bay (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened Corroded and holed (5.3.3 (b) (i)) | 1 |
| Offside Rear Suspension arm corroded and seriously weakened lower |2.4.G.1| | 1 |
| Nearside Rear Body panel corroded and likely to cause injury wheel arch sharp edges (6.2.1 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is inadequately repaired split between repaired section and subframe (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis / inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis / inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded |6.1.1 |c| |i|| | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded |6.1.1 |c| |i|| | 1 |
| Nearside Rear Service brake excessively binding suspected handbrake cable |1.2.1 |f|| | 1 |
| Rear coil spring broken BOTH |2.4.C.1a| | 1 |
| Offside Rear Floor excessively deteriorated holed |6.2.4 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint ball joint broken |2.4.G.2| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded front outrigger |2.4.A.3| | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened damper mounting |2.4.G.1| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis rail and floor pan as marked in yellow chalk (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner and outer sill section as marked in yellow chalk (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill section as marked in yellow chalk (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill section as marked in yellow chalk (6.2.2 (d) (i)) | 1 |
| Emissions not tested |7.4.B.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is severely distorted |5.2.6| | 1 |
| Emissions not tested due to exhaust blowing (8.2.1.2 (d)) | 1 |
| Nearside Rear Brake hose leaking on an air braking system |1.1.12 |c| |i|| | 1 |
| Nearside Front Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded (6.1.1 (c) (i)) | 1 |
| Front position lamp|s| not working n/s front |1.1.A.3b| | 1 |
| Emissions not tested Major exhaust leak (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced undersill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced undersill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded main chassis frame rail side frame |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded main chassis frame rail side frame |2.4.A.3| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Front chassis rail frame structure inner sides of arch |6.1.B.2| | 1 |
| Emissions oxygen sensor obviously defective (8.2.2.1 (a)) | 1 |
| Exhaust has a major leak of exhaust gases front silencer and rear joint |6.1.2 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail lower face |5.3.6 |a| |i|| | 1 |
| Offside Rear Lower Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 1 |
| Rear Shock absorbers has a serious fluid leak Both |5.3.2 |b|| | 1 |
| Emissions not tested Due to exhaust leak (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension arm attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Front Suspension arm attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower shocker mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower shocker mount (5.3.6 (a) (i)) | 1 |
| Centre Front Front position lamp|s| not working n/s side light |1.1.A.3b| | 1 |
| Nearside Rear Outer Body has a projection caused by corrosion N/SR outer seal has corroded away |6.1.C.1| | 1 |
| Offside Rear Brake cable has restricted free movement does not move |1.1.15 |e|| | 1 |
| Offside Rear Brake lever has restricted free movement at caliper does not move |1.1.15 |e|| | 1 |
| Offside Rear Inner Brake disc significantly and obviously worn face |1.1.14 |a| |i|| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill hole |2.4.A.3| | 1 |
| Offside Front wheel bearing rough when rotated not checked.. brake binding |2.5.A.2| | 1 |
| Nearside Front Wheel bearing play so excessive that directional control is impaired collapsed (5.1.3 (a) (ii)) | 1 |
| Parking brake inoperative on one side L 78kgf R 36kgf (1.4.1 (a)) | 1 |
| Front Service brake grabbing severely both (1.2.1 (c)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill--inner/outer/floor area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill--inner/outer/floor area (5.3.6 (a) (i)) | 1 |
| Parking brake inoperative on one side L 78kgf R 78kgf (1.4.1 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Lower belt mounting outer sill |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded Lower belt mounting outer sill |5.2.6| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Body panel corroded and likely to cause injury wheel arch |6.2.1 |a| |i|| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits due to exhaust blow |7.3.D.3| | 1 |
| Nearside Front Position lamp not working not working correctly (flashes) (4.2.1 (a) (ii)) | 1 |
| Offside Front Position lamp not working not working correctly (flashes) (4.2.1 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed by corrosion (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened arm (5.3.3 (b) (i)) | 1 |
| Hydraulic fluid leaking continuously posing a serious risk to road safety Power Steering (8.4.1 (a) (ii)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel Arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Parking brake lever inoperative (1.1.6 (d)) | 1 |
| Nearside Rear coil spring broken broken |2.4.C.1a| | 1 |
| Brake pipe leaking on a hydraulic braking system front rear pipe |1.1.11 |b| |ii|| | 1 |
| Central Drivers view of the road through the swept area of the windscreen materially affected by an obstruction (3.1 (a) (ii)) | 1 |
| Emissions not tested lambda reading too high exhaust blow (8.2.1.2 (d)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure |5.3.3 |a| |i|| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover missing |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover missing |2.4.G.2| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Rear sill |5.2.6| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect and offside (4.1.2 (c)) | 1 |
| Front Lower Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced door sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill area (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to wing mounting point (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to chassis/sill area (6.2.2 (d) (i)) | 1 |
| Subframe mounting prescribed area excessively corroded significantly reducing structural strength Both sides front chassis rails corroded (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area is excessively corroded sill backing at rear |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassi |5.3.6 |a| |i|| | 1 |
| Exhaust emits clearly visible black smoke during acceleration (8.2.1.2 (g)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced OUTER SILL (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced OUTER SILL (6.1.1 (c) (i)) | 1 |
| Nearside Upper coil spring broken |2.4.C.1a| | 1 |
| Offside Upper coil spring broken |2.4.C.1a| | 1 |
| Nearside Rear Anti-roll bar linkage insecure and impairing directional stability |5.3.3 |a| |ii|| | 1 |
| Front Front position lamp(s) not working (1.1.A.3b) | 1 |
| Offside Rear wheel bearing has excessive play (2.6.2) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner arch |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner arch |6.1.A.1| | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rails |6.1.1 |c| |i|| | 1 |
| Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sills |6.1.1 |c| |i|| | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sills both sides (6.1.1 (c) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction p0420 catalyst below threshold (8.2.1.2 (h)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS RAIL (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS RAIL (5.3.6 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area is inadequately repaired Both sides sills (5.3.6 (a) (i)) | 1 |
| Offside Body panel damaged and likely to cause injury Door mirror cluster damaged, sharp edges exposed (6.2.1 (a) (i)) | 1 |
| Nearside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/wing (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wing/ sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill/quarter panel/ arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill/quarter panel/ arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded outer sill area |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill hoed with in 30 cm of mount |2.4.A.3| | 1 |
| Nearside Front Steering locking device missing |2.1.3 |d|| | 1 |
| Offside Front Steering locking device missing |2.1.3 |d|| | 1 |
| Central Exhaust has a major leak of exhaust gases cen (6.1.2 (a)) | 1 |
| Offside Rear Hydraulic brake calliper leaking brake hose connection |1.1.16 |b| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill corroded |5.2.6| | 1 |
| Headlamp aim not tested (4.1.2 (b)) | 1 |
| Offside Front Subframe mounting prescribed area is fractured |2.4.A.3| | 1 |
| Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner/wing |5.3.6 |a| |i|| | 1 |
| Offside Rear Position lamp showing white light to the rear |4.2.3 |a| |ii|| | 1 |
| Offside Rear Position lamp lens seriously defective |4.2.1 |b|| | 1 |
| Offside Rear Stop lamp|s| showing white light to the rear |4.3.3 |a| |ii|| | 1 |
| Nearside Rear Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect bulb not fitted correctly (4.1.2 (c)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis under ARB mounting (5.3.6 (a) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch chassis rail (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch chassis rail (5.3.6 (a) (i)) | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner upper wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Brake hose leaking on a hydraulic braking system brake flexi pipe (1.1.12 (c) (ii)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting near radiator (6.2.2 (d) (i)) | 1 |
| Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced both sides inn side sills (6.1.1 (c) (i)) | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Suspension arm ball joint likely to become detached lock pin missing (5.3.4 (a) (ii)) | 1 |
| Nearside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting innersill (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced battery box (6.1.1 (c) (i)) | 1 |
| Power steering pipe/hose excessively corroded COMING OUT OF RACK (2.1.5 (g) (i)) | 1 |
| Offside Front Inner Brake prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg at front subframe mounting point (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg around front subframe mounting point (6.1.1 (c) (i)) | 1 |
| Nearside Outer Body panel corroded and likely to cause injury outer sill (6.2.1 (a) (i)) | 1 |
| Nearside Rear Upper Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill / quarter panel (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Sill / quarter panel (7.1.1 (a) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced offside and nearside sills (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.1 |c| |ii|| | 1 |
| Nearside Front Anti-roll bar likely to become detached link arm |5.3.3 |a| |ii|| | 1 |
| Nearside Front Body has a sharp edge caused by damage wing |6.1.C.1| | 1 |
| Front position lamp|s| not working offside and nearside |1.1.A.3b| | 1 |
| Offside Front Additional braking device component overheating |3.6.I.4| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg/inner wing |6.1.A.1| | 1 |
| Power steering component|s| leaking steering rack leaking oil out of both end gaitors |2.3.3b| | 1 |
| Rear Brake disc significantly and obviously worn both |1.1.14 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength boot floor area |marked with chalk| |5.3.6 |a| |i|| | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak mid/rear section joint blowing |8.2.1.1 |b|| | 1 |
| Nearside Front Suspension arm pin or bush excessively worn lower arm rear bush |5.3.4 |a| |i|| | 1 |
| Power steering pipe/hose leaking dripping continuously when engine running (2.1.5 (a)) | 1 |
| Fuel cap/sealing device ineffective wont open (6.1.3 (b) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength extensive corrosion to off side front chassis rail area around anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded rear of near side sill panel area |5.2.6| | 1 |
| Rear Fuel system component leaking At fuel tank area. (6.1.3 (b) (i)) | 1 |
| Offside Front Braking system leaking to rear pipe |3.6.A.1| | 1 |
| Indicator switch inoperative (4.4.2 (a) (ii)) | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Hydraulic fluid leaking excessively |8.4.1 |a| |i|| | 1 |
| Position lamp showing red light to the front both blue (4.2.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail by front subframe mounting |5.3.6 |a| |i|| | 1 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded side sill |2.4.A.3| | 1 |
| Emissions unable to be completed due to leak (8.2.1.2 (d)) | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced main beam (4.1.4 (b)) | 1 |
| Nearside Rear Lower Suspension arm insecurely attached bolts (5.3.3 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm insecurely attached bolts (5.3.3 (a) (i)) | 1 |
| Offside Front Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Central Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Offside Front Brake prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases cat |7.1.2| | 1 |
| Offside Inner Front Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Nearside Inner Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Offside Inner Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect bulb |1.8.A.1b| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced excessive corrosion on inner sill |7.1.1 |a| |i|| | 1 |
| Offside Front Anti-lock braking system component inappropriately repaired |3.4.4| | 1 |
| Emissions not tested misfire under load (8.2.1.2 (d)) | 1 |
| Front Sub-frame attachment bracket/mounting insecure both rear fixing bolts missing (5.3.3 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg in engine bay and wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg in engine bay and wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis at bottom and outer |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength chassis at bottom and outer |2.4.A.3| | 1 |
| Headlamp not working on dipped beam Offside |4.1.1 |a| |ii|| | 1 |
| Hydraulic brake calliper leaking Offside rear |1.1.16 |b| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage insecurely attached broken (5.3.3 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti-roll bar d bush area |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.A.1| | 1 |
| Rear Electrical wiring insecure |1.9.2a| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded Floor/sill |5.2.6| | 1 |
| Brake pedal anti-slip provision worn smooth |3.3.A.1b| | 1 |
| Offside Seat belt not functioning as intended wont unclip under pressure |7.1.2 |c|| | 1 |
| Offside Front Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Offside Rear Upper Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Brake pipe connection leaking on a hydraulic braking system front to rear leaking at connector (1.1.11 (b) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded & holed (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded & holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear of sill corroded 30cm from mounting (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear of sill corroded 30cm from mounting (7.1.1 (a) (i)) | 1 |
| Nearside Rear Fuel tank leaking damp & stained (6.1.3 (b) (i)) | 1 |
| Drivers airbag missing steering wheel (7.1.5 (a)) | 1 |
| Horn not loud enough to be heard by another road user |1.6.2b| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering floor |6.1.1 |c| |ii|| | 1 |
| Offside Front Front position lamp|s| not working headlight |1.1.A.3b| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Body component damaged and likely to cause injury lamb |6.2.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floorpan (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill Under car Corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill under car corroded (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill has corrosion also within 30cm of subframe mounting |6.1.1 |c| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength archs (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 1 |
| Offside Front Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.1 |c| |ii|| | 1 |
| Supplementary restraint system warning lamp indicates a fault AIRBAG LAMP ON |7.1.6 |a|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Chassis leg (6.2.2 (d) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Chassis leg (6.2.2 (d) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Marked in Yellow (6.2.2 (d) (ii)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced WHEEL ARCH |6.1.1 |c| |i|| | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced WHEEL ARCH |6.1.1 |c| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SEAL |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SEAL |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced WHEEL ARCH |7.1.1 |a| |i|| | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WHEEL ARCH |5.3.6 |a| |i|| | 1 |
| Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Brake pivot has restricted free movement |3.5.1k| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both rear inner arches |6.1.1 |c| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired inner wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired inner wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill at rear |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill at rear |5.2.6| | 1 |
| Braking system leaking hydraulic system failed during brake test |3.6.A.1| | 1 |
| Anti-roll bar linkage has excessive play in a ball joint offside rear broken |2.4.G.2| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering both rear outer sill |6.1.1 |c| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases middle to rear leaking (6.1.2 (a)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassi (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer cill (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer cill (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner cill (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting behind wheel (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area marked with chalk (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area marked with chalk (5.3.6 (a) (i)) | 1 |
| Nearside Front Hydraulic brake calliper insecurely mounted (1.1.16 (c) (i)) | 1 |
| Offside Front Headlamp aim beam image too far to the right |1.6.B4| | 1 |
| Nearside Front Additional braking device wiring not secure |3.6.I.5| | 1 |
| Nearside Rear Anti-roll bar linkage insecure drop link |2.4.G.1| | 1 |
| Nearside Rear Lower Hydraulic brake calliper inadequately mounted bolt appears cross threaded and not fully home (1.1.16 (c) (i)) | 1 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded sill rear end |2.4.A.3| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer body sill. |7.1.1 |a| |i|| | 1 |
| Nearside Front Service brake excessively binding wheel will not turn by hand. |1.2.1 |f|| | 1 |
| Offside Rear Outer Body panel damaged and likely to cause injury arch (6.2.1 (a) (i)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Rear outer sill (7.1.1 (a) (i)) | 1 |
| Rear Braking system leaking brake caliper |3.6.A.1| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail. (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill. (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill. (6.2.2 (d) (i)) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill end in wheel tub (7.1.1 (a) (i)) | 1 |
| Offside Front Anti-lock braking system wheel speed sensor missing (1.6 (c)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Anti-lock braking system wheel speed sensor missing (1.6 (c)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened poorly repaired (5.3.3 (b) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn Nearside and Offside d bushes (5.3.4 (a) (i)) | 1 |
| Anti-roll bar linkage has excessive play in a ball joint both rear |2.4.G.2| | 1 |
| Nearside Front Upper Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Rear Brake performance not tested |3.7.A.1| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill corroded and holed |6.1.B.2| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension arm corroded and seriously weakened wishbone |2.4.G.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded outer sil |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded outer sil |5.2.6| | 1 |
| Offside Front Lower Body panel insecure wing |6.2.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail in engine bay |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail in engine bay |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Front Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Front Body panel likely to become detached (6.2.1 (a) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases Joint leaking (6.1.2 (a)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength *Chassis* (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength *Chassis* (5.3.6 (a) (i)) | 1 |
| Central Rear Stop lamp not working High level |1.2.1b| | 1 |
| Emissions not tested Due to exhaust leak |7.3.A.1| | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt Lower and upper (5.3.4 (b) (ii)) | 1 |
| Offside Rear Suspension arm insecure and impairing directional stability arm corroded Insecure (5.3.3 (a) (ii)) | 1 |
| Front Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
| Offside Rear Outer Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Central Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings middle |6.1.B.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded floor and outer sill |2.4.A.3| | 1 |
| Nearside Front Coil spring with an unsafe modification springs been cut (5.3.1 (d) (i)) | 1 |
| Offside Front Coil spring with an unsafe modification spring been cut (5.3.1 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Torque/reaction arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect lens misty (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect lens misty (4.1.2 (c)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis leg near front subframe (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front and rear floors |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower quarter panel |5.3.6 |a| |i|| | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arches |5.3.6 |a| |i|| | 1 |
| Offside Front Brake rod has restricted free movement brake binding |1.1.15 |e|| | 1 |
| Emissions not tested Exhaust leak. |7.3.A.1| | 1 |
| Nearside Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Lower Anti-roll bar fractured ball joint detached (5.3.3 (b) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn outer ball joint (5.3.4 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced N/S OUT SIDE SILL TO |7.1.1 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill corroded (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill corroded and not welded (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to inner wheel arch corroded (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill corroded (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch next to shock corroded (6.1.1 (c) (i)) | 1 |
| Service brake excessively binding both front |1.2.1 |f|| | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid brake calliper |1.1.16 |b| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded s |2.4.A.3| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Front Braking system leaking Suspect banjo bolt washers |3.6.A.1| | 1 |
| Front Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 1 |
| Offside Front Lower Steering linkage ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Rear Exhaust system not adequately supported broken |7.1.1| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits exhaust leaking |7.3.D.3| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor |6.1.1 |c| |i|| | 1 |
| Offside Front Electrical wiring inadequately supported abs harness |1.9.2a| | 1 |
| Offside Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected sill |5.3.6 |a| |ii|| | 1 |
| Nearside Front Lower Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill within 30cm of seat belt mount |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill within 30cm of seat belt mount |5.2.6| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering by subframe mtg |6.1.1 |c| |ii|| | 1 |
| Exhaust fumes causing a danger to health of persons on board tail pipe missing |6.1.2 |b| |ii|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outter seal |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outter seal |7.1.1 |a| |i|| | 1 |
| Offside Front Brake pipe at imminent risk of failure or fracture too rear (1.1.11 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassies antiroll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings marked with yellow chalk |6.1.B.2| | 1 |
| Braking system leaking offside rear caliper |3.6.A.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded OUTER sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded SILL / WING corroded |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded OUTER sill |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Emissions not tested Rear exhaust not attached (8.2.1.2 (d)) | 1 |
| Exhaust has a major leak of exhaust gases Rear exhaust section not attached (6.1.2 (a)) | 1 |
| Nearside Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` object hanging from mirror |8.3.1e| | 1 |
| Exhaust fumes entering cabin |6.1.2 |b| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis around anti roll bar mtg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded around anti roll bar mtg |2.4.A.3| | 1 |
| Nearside Front Macpherson strut has excessive movement at the upper attachment |2.5.A.1c| | 1 |
| Offside Front Macpherson strut has excessive movement at the upper attachment |2.5.A.1c| | 1 |
| Offside Front Braking system leaking fluid leaking from calliper |3.6.A.1| | 1 |
| Offside Front Upper Anti-roll bar linkage insecure broken in half |2.4.G.1| | 1 |
| Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings above torque reaction arm |6.1.B.2| | 1 |
| Nearside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings behind wheel |6.1.B.2| | 1 |
| Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| brake disc in such a condition that it is seriously weakened both front and rear |3.5.1i| | 1 |
| Windscreen in such a condition that visibility through swept area is seriously affected (3.2 (c) (ii)) | 1 |
| Emissions not tested DUE TO CAT MISSING (8.2.1.2 (d)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced N/S and O/S front jacking points excessive corrosion (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to inner sill excessive corrosion (6.1.1 (c) (i)) | 1 |
| Offside Rear Braking system leaking Caliper leaking |3.6.A.1| | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases exhaust box |7.1.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases exhaust box tail pipe |7.1.2| | 1 |
| Headlamps matched pair incorrect colour |4.1.4 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis within 30cm of anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within 30cm of anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill excessively corroded and inadequately repaired within 30cm of seat belt lower mounting (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill inadequately repaired and excessively corroded within 30cm of seat belt lower mounting (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing next to chassis |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing top |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis section |2.4.A.3| | 1 |
| Anti-roll bar ball joint likely to become detached offside rear broken (5.3.4 (a) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area is inadequately repaired rear of outer sill (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded outer sills at rear both n/s and o/s |5.2.6| | 1 |
| Subframe mounting prescribed area is excessively corroded front chassis legs both n/s and o/s |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer door sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded Outer sill perforated |5.2.6| | 1 |
| Nearside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch |6.1.B.2| | 1 |
| Nearside Front Body panel corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Front Headlamp light source and lamp not compatible both dip beam bulb (4.1.4 (c)) | 1 |
| Offside Rear Upper Suspension arm fractured + heavily corroded (5.3.3 (b) (ii)) | 1 |
| Nearside Rear Inner Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Inner Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar insecurely attached (5.3.3 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Link mount (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Link mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Road wheel fixing loose |5.2.1 |a| |i|| | 1 |
| Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting n/s/r sill corroded (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s/r sill corroded (6.2.2 (d) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded around anti roll bar mounting |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |inner sill| |2.4.A.3| | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both sides inner sills |6.1.1 |c| |i|| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded upper arm mounting |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases back box to centre pipe |7.1.2| | 1 |
| Front Power steering pipe/hose corroded such that the steering is adversely affected engine bay (2.1.5 (g) (ii)) | 1 |
| Brake performance not tested fluid leaking |3.7.A.1| | 1 |
| Emissions not tested exhaust broken |7.3.A.1| | 1 |
| Seat belt anchorage prescribed area is excessively corroded osr inner sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nsr floor |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nsr inner sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nsr sill |5.2.6| | 1 |
| Suspension has inadequate clearance with the chassis |2.4.A.1a| | 1 |
| Front Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded underbody floor to sill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Bottom of Chassis rail by Front anti-roll bar mounting bracket. |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is fractured Bottom of Chassis rail by Front anti-roll bar mounting bracket. |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Under inside of wheel arch by Front anti-roll bar mounting bracket. |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Under front edge of wheel arch. |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Under front edge of wheel arch. |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner sill area. |5.2.6| | 1 |
| Offside Rear Braking system leaking Brake calliper leaking. |3.6.A.1| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill panel. (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases System broken at joint between middle & rear sections. (6.1.2 (a)) | 1 |
| Emissions not tested Due to condition of exhaust affecting results. (8.2.1.2 (d)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced in the inner arch (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced in the inner arch (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill, chalked (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill, chalked (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced INNER SILL TO FLOOR (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced LOWER SILL INNER SILL HEAVY CORROSION (7.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing chalked (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength at roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage insecure and impairing directional stability Anti-roll bar drop link detatched (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wing/front panel (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wing/front panel (6.1.1 (c) (i)) | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings nearside outer sill |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill within 30cm of seatbelt mounting |7.1.1 |a| |i|| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits rear silencer tailpipe cracked and loose |8.2.1.2 |c|| | 1 |
| Offside Headlamp aim beam image obviously incorrect bulb not fitted correctly |1.8.A.1b| | 1 |
| Central Front Exhaust emissions likely to be affected by an exhaust leak leaking above lambada sensor, (8.2.1.1 (b)) | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill
|5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases joint from center to rear box |7.1.2| | 1 |
| Front Undertray insecure (8.1.1 (b) (i)) | 1 |
| Offside Rear Tie bar/rod worn and seriously weakened |2.4.G.1| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded NS + OS inner wheel arch`s chassis legs |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and nearside rear inner and outer sills (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and nearside rear upper inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system pipe burst during mot (1.1.11 (b) (ii)) | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Front Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Nearside Front Front suspension locking device missing |2.5.A.4| | 1 |
| Offside Body component damaged and likely to cause injury mirror shroud (6.2.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired chassis inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Centre Rear coil spring broken |2.4.C.1a| | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Emissions not tested obvious exhaust leak |8.2.1.2 |d|| | 1 |
| Central Exhaust has a major leak of exhaust gases center to rear pipe |6.1.2 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Body panel insecure wing corroded |6.2.1 |a| |i|| | 1 |
| Nearside Rear Body has a sharp edge caused by damage lamp cluster |6.1.C.1| | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Arch & outer sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Arch & outer sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 1 |
| Nearside Rear Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is severely distorted |5.2.6| | 1 |
| Nearside Rear Inner brake disc in such a condition that it is seriously weakened scored |3.5.1i| | 1 |
| Offside Rear Inner brake disc in such a condition that it is seriously weakened scored |3.5.1i| | 1 |
| Nearside Rear Anti-roll bar linkage attachment bracket/mounting likely to fail (5.3.3 (b) (ii)) | 1 |
| Nearside Front Lower Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced backing sill/floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Anti-lock braking system component inappropriately repaired |3.4.4| | 1 |
| Brake pipe inappropriately repaired |3.6.A.3| | 1 |
| Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Front Wheel nut|s| missing |4.2.A.1e| | 1 |
| Rear Wheel nut|s| missing |4.2.A.1e| | 1 |
| Nearside Track rod end ball pin shank loose |2.2.B.1c| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor/sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Power steering pipe/hose excessively corroded Pipes to steering rack (2.1.5 (g) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Hole in floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Main chassis rail |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings main chassis rail |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mount |2.4.A.3| | 1 |
| Subframe mounting prescribed area is excessively corroded both front chassis |2.4.A.3| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength All sills inside and out heavily corroded. (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front chassis leg (engine bay) (5.3.6 (a) (i)) | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill holed |6.1.B.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded |7.1.1 |a| |i|| | 1 |
| Brake hydraulic reservoir leaking hydraulic fluid |3.6.A.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill/floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor/sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch/ bulkhead (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch/bulkhead (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch (5.3.6 (a) (i)) | 1 |
| Offside Front Power steering component|s| leaking |2.3.3b| | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded (6.2.2 (d) (i)) | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill coroded (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill coroded (6.2.2 (d) (i)) | 1 |
| Nearside Front Lower Shock absorbers insecurely attached bolt loose marked white |5.3.2 |a| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced CHASSIS (6.1.1 (c) (i)) | 1 |
| Nearside Front Body insecure and dangerous to other road users wing |6.1.B.1b| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill |5.3.6 |a| |i|| | 1 |
| Exhaust silencer likely to become detached back box missing |8.1.1 |b| |ii|| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill corroded (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill corroded (6.1.1 (c) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Offside Front Lower Suspension component ball joint likely to become detached bolt to short mot lock in nut (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Coil spring fractured or broken at the top (5.3.1 (b) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength roll bar mounting outer chassis (5.3.6 (a) (i)) | 1 |
| Emissions oxygen sensor obviously defective wires ripped out of sensor and hanging down, sensor body missing and slightly leaking exhaust gas (8.2.1.1 (a)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill section as marked (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill section as marked (5.3.6 (a) (i)) | 1 |
| Rear Exhaust system insecure (half eaten shoe laces used to try and hold exhaust system in place ) (6.1.2 (a)) | 1 |
| Rear Anti-roll bar insecurely attached (5.3.3 (a) (i)) | 1 |
| Offside Rear Inner Integral body structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Emissions unable to be completed 2 separate major leaks (8.2.1.2 (d)) | 1 |
| Rear Exhaust has a major leak of exhaust gases REAR JOINT (6.1.2 (a)) | 1 |
| Emissions unable to be completed HAS EURO CAT FITTED CHOKED EMISSIONS MACHINE UP (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Antiroll bar area (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 1 |
| Front Braking system leaking to rear |3.6.A.1| | 1 |
| Offside Rear Floor excessively deteriorated battery compartment (6.2.4 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner and outer sill area (5.3.6 (a) (ii)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill area |7.1.1 |a| |i|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner wing area |6.1.1 |c| |ii|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill and chassis rail |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch |7.1.1 |a| |i|| | 1 |
| Brake disc significantly and obviously worn all 4 (1.1.14 (a) (i)) | 1 |
| Central Side repeater incorrect colour |1.4.A.2f| | 1 |
| Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced rear of the inner and outer bodysill structure excessively corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced rear of the inner and outer bodysill structure excessively corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded body |2.4.A.3| | 1 |
| coil spring broken N/S/F AND BOTH REAR |2.4.C.1a| | 1 |
| Nearside Front Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL |6.1.B.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch , inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury seal (6.2.1 (a) (i)) | 1 |
| Offside Front Front position lamp|s| not working side light not working |1.1.A.3b| | 1 |
| Offside Front Front position lamp|s| not working side light inoperative |1.1.A.3b| | 1 |
| Electronic parking brake warning indicates a malfunction |3.1.7| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak back box to the middle section (8.2.1.1 (b)) | 1 |
| Offside Rear Lower Integral body structure is fractured and structural rigidity is significantly reduced corner (6.1.1 (a) (i)) | 1 |
| Offside Front Position lamp not working sidelight (4.2.1 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm locating pin retaining device missing outer ball joint |2.4.G.3b| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded OUTER SILL |2.4.A.3| | 1 |
| Front Exhaust emissions exceed manufacturers specified limit CO (8.2.2.2 (a)) | 1 |
| Nearside Front Position lamp not working Bulb replaced |4.2.1 |a|| | 1 |
| Nearside Front Direction indicator obviously incorrectly positioned |1.4.A.2b| | 1 |
| Offside Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within 30 cm of subframe mount (6.1.1 (c) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis Leg by Anti Roll Bar Mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis Leg by Anti Roll Bar Mounting (5.3.6 (a) (i)) | 1 |
| Nearside Body has a sharp edge caused by damage mirror back |6.1.C.1| | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid calliper |3.6.A.1| | 1 |
| Road wheel more than one fixing loose (5.2.1 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rear section of sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure is fractured and structural rigidity is significantly reduced very front chassis corroded can be seen through front bumper behind wheel arch (6.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner wing |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner wing |6.1.1 |c| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases centre section (6.1.2 (a)) | 1 |
| Emissions not tested exhaust has major leak before rear silencer. (8.2.1.2 (d)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sills (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint link bar |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint link bar |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint link bar |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint link bar |2.4.G.2| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wheel arch strut top mount (5.3.6 (a) (ii)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill front and rear (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill complete (7.1.1 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill complete (7.1.1 (a) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill front and rear (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within 30 cm of lower suspension arm (5.3.6 (a) (i)) | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits leak on exhaust rear joint |7.3.D.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Back edge of sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength innerwing corroded |5.3.6 |a| |i|| | 1 |
| Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded SILL |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases Middle box /and gasket front flange |6.1.2 |a|| | 1 |
| Nearside Rear Suspension arm likely to fail |5.3.3 |b| |ii|| | 1 |
| Offside Rear Suspension arm likely to fail |5.3.3 |b| |ii|| | 1 |
| Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded various |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded various |2.4.A.3| | 1 |
| Offside Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail under bonnet (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Coil spring fractured or broken broken (5.3.1 (b) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor under body area |5.2.6| | 1 |
| Emissions not tested no cat (8.2.1.2 (d)) | 1 |
| Nearside Rear Outer Seat belt anchorage likely to become detached in the event of a collision sill (7.1.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength main chassis member above antiroll bar mount |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area fractured significantly reducing structural strength main chassis member above antiroll bar mount |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch chassis leg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch chassis leg |2.4.A.3| | 1 |
| Headlamp aim not tested both dipped beam not working (4.1.2 (b)) | 1 |
| Offside Rear Hydraulic brake calliper leaking leaking fluid (1.1.16 (b) (i)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill area (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill area (6.2.2 (d) (i)) | 1 |
| Nearside Rear Parking |secondary brake| on a single line braking system has no recorded effort at a wheel wheel spin freely when handbrake on |1.3.1 |a| |ii|| | 1 |
| Brake lever has insufficient reserve travel too high |1.1.2 |a|| | 1 |
| Suspension component mounting prescribed area is excessively corroded near side outer sill |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded off side outer sill |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner/outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis section |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis section |6.2.2 |d| |i|| | 1 |
| Front Lower Power steering pipe|s| or hose|s| leaking pipes excess corroded and leaking |2.3.3b| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill to wheel arch |6.1.B.2| | 1 |
| Offside Rear Anti-roll bar has excessive play in a ball joint link upper ball joint worn to excess |2.4.G.2| | 1 |
| Offside Front Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings N/S/R BOOT FLOOR EXCESSIVELY CORRODED |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings O/S/R BOOT FLOOR EXCESSIVELY CORRODED |6.1.B.2| | 1 |
| Nearside Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings N/S/F UPPER CHASSIS LEG EXCESSIVELY CORRODED |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings O/S/F UPPER CHASSIS LEG EXCESSIVELY CORRODED |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings O/S/F LOWER FLOOR CORRODED |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings N/S/R INNER WHEEL ARCH EXCESSIVELY CORRODED |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings O/S/R INNER WHEEL ARCH CORRODED |6.1.B.2| | 1 |
| Service brake is causing the steering wheel to severely pull one way |3.7.C.2| | 1 |
| Nearside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Chassis holed forward of suspension arm mounting |6.1.B.2| | 1 |
| Offside Front Seat belt locking mechanism does not secure or release Won`t release under load |5.2.5a| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mounting point |2.4.A.3| | 1 |
| Offside Rear Body panel corroded and likely to cause injury outer siil holed near suspsion ponit with 30cm (6.2.1 (a) (i)) | 1 |
| Central Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill, (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg area |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg area |2.4.A.3| | 1 |
| Rear Brake lining(s) less than 1.5 mm thick (1.1.13 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to floor |6.1.1 |c| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill /undersill/inner wheel arch areas (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced undersill area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floorpan area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch area (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg/rail (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg/rail (5.3.6 (a) (i)) | 1 |
| Headlamp not working on dipped beam o/s |1.7.5a| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor/inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Hole in inner sill and wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Hole in inner sill and wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill, (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Passenger`s airbag obviously defective Air bag light on |5.4.1| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill |6.1.B.2| | 1 |
| Braking system leaking Nearside rear caliper |3.6.A.1| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill outer (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill outer (6.1.1 (c) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Front Position lamp not working both lights (4.2.1 (a) (ii)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits 1.035 (8.2.1.2 (b)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both front headlamps (4.1.4 (b)) | 1 |
| Front Inner Anti-roll bar rubber bush deteriorated resulting in excessive movement both d bushes |2.4.G.2| | 1 |
| Offside Rear Braking system leaking caliper joint/pipe |3.6.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (near anti roll mount) (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (near anti roll mount ) (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/inner arch (5.3.6 (a) (i)) | 1 |
| Offside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill panel |7.1.1 |a| |i|| | 1 |
| Nearside Rear Side repeater not working |1.4.A.2c| | 1 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` air fresheners |8.3.1b| | 1 |
| Central Seat belt anchorage prescribed area strength or continuity significantly reduced Offside floor to sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis x2 areas (5.3.6 (a) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced undersill |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced undersill |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis by top wish bone |5.3.6 |a| |i|| | 1 |
| Nearside Front Vehicle structure is fractured and structural rigidity is significantly reduced rotted hole underneath bonnet (6.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Brake pipe leaking on a hydraulic braking system Front to rear brake pipe (1.1.11 (b) (ii)) | 1 |
| Brake performance not tested Due to leaking brake pipe (1.2.1 (g)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced inside wheel arch |2.4.G.1| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced inside wheel arch |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded floor/inner sill |2.4.A.3| | 1 |
| Offside Rear Brake lever has restricted free movement |3.5.1k| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded SILL |5.2.6| | 1 |
| Nearside Front Integral body structure is fractured and structural rigidity is significantly reduced chassis leg at anti-roll mount (6.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg at anti-roll bar mount (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded inner and outer sills |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis at anti - roll bar mounting bracket fixing |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis/inner wing at anti - roll bar mounting fixing point |2.4.A.3| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Wheel arch (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis rail (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced & Inner sills (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced & Inner sills (6.1.1 (c) (i)) | 1 |
| Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Parking brake inoperative on one side Low effort (1.4.1 (a)) | 1 |
| Offside Parking brake inoperative on one side Low effort (1.4.1 (a)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Upper Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS SECTION (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS SECTION (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL TO FLOOR (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases BACK BOX CONNECTION (6.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is severely distorted chassis |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner chassis |2.4.A.3| | 1 |
| Front Anti-roll bar linkage missing |2.4.G.1| | 1 |
| Nearside Front Anti-roll bar linkage damaged and seriously weakened Also Half Missing |2.4.G.1| | 1 |
| Offside Front Anti-roll bar linkage damaged and seriously weakened Also Half Missing |2.4.G.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired inadequately welded |5.2.6| | 1 |
| Nearside Suspension spring mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded inner and outer sills |2.4.A.3| | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Rear position lamp|s| incorrect colour lens broken |1.1.A.3e| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill/arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill/arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Passenger`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inside of wheel arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting within limits of rear crash bar (6.2.2 (d) (i)) | 1 |
| Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired inner wheel arch and inner sill (5.3.6 (a) (i)) | 1 |
| Front Hydraulic fluid leaking excessively (8.4.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail split adjacent to subframe mounting and anti-roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail corroded above anti-roll bar mounting and lower section starting to de-laminate (prior to splitting) (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/floor corroded and holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is severely distorted centra chassie |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is severely distorted centra chassie |5.2.6| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outter sill (6.2.2 (d) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced SILL |7.1.1 |a| |i|| | 1 |
| Rear Anti-roll bar ball joint excessively worn Both sides (5.3.4 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Chassis leg where the anti roll bar connects |6.1.1 |c| |ii|| | 1 |
| Offside Front obligatory indirect vision device seriously damaged affecting the rear view sun visor loose |8.1.2a| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill holed and corroded (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within 30cm of suspension mount (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassie |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassie |2.4.A.3| | 1 |
| All direction indicators incorrect colour (4.4.3 (a)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is fractured hole in outer sill |5.2.6| | 1 |
| Offside Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 1 |
| Centre Parking brake mechanism/associated mounting prescribed area is fractured |3.1.9| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Chassis leg |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Jacking point area |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill area |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Battery box |6.1.B.2| | 1 |
| Battery insecure Due to corrosion bottom of battery box |1.9.1| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill area |6.1.B.2| | 1 |
| Offside Outer Front Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 1 |
| Offside Front Body panel insecure wing |6.2.1 |a| |i|| | 1 |
| Offside Rear Battery insecure and likely to fall from carrier under battery holed |4.13 |a| |ii|| | 1 |
| Offside Rear Braking system leaking @ brake caliper piston |3.6.A.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis by anit roll bar fixing (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor .small hole (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor small hole (5.3.6 (a) (i)) | 1 |
| Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt both sides |5.3.4 |b| |ii|| | 1 |
| Offside Rear Parking brake inoperative on one side low effort (1.4.1 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill. (7.1.1 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded sills both sides |2.4.A.3| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Boot Floor |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Under Sill |6.2.2 |d| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail/inner wing excessively corroded within 30cms of front suspension mountings (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired Outer Sill to Front Wing, Corroded and Holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner & Outer sills Holed and Corroded (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Boot Floor in Side wells, Holed and Corroded near Rear Bumper and Suspension Components. (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Boot Floor in Side wells, Holed and Corroded near Rear Bumper and Suspension Components. (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis Holed and Corroded by Sub frame Mountings (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis Holed and Corroded by Sub frame Mountings (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure is so deformed it is likely to adversely affect braking or steering chassis |6.1.1 |a| |ii|| | 1 |
| Nearside Front Vehicle structure is so deformed it is likely to adversely affect braking or steering inner wing 30 cm break and stering |6.1.1 |a| |ii|| | 1 |
| Offside Front Vehicle structure is so deformed it is likely to adversely affect braking or steering inner wing within 30 cm of staring and suspention |6.1.1 |a| |ii|| | 1 |
| Offside Rear Tie bar/rod insecure droplink adrift |2.4.G.1| | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed |6.1.1 |c| |i|| | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed front and back |6.1.1 |c| |i|| | 1 |
| Emissions not tested No engine oil on dipstick |7.3.A.1| | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system section of front to rear (1.1.11 (b) (ii)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced Both rear inner sills (7.1.1 (a) (i)) | 1 |
| Rear Brake disc significantly and obviously worn both sides (1.1.14 (a) (i)) | 1 |
| Power steering pipe/hose leaking Power steering fluid dripping from underside of vehicle from behind plastic under-tray. |2.1.5 |a|| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Nearside rear inner sill |6.1.B.2| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Offside rear inner sill |6.1.B.2| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Nearside front chassis leg |6.1.B.2| | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Ball joint has excessive play NEARSIDE FRONT INNER RACK END |2.2.B.1f| | 1 |
| Braking system leaking NEARSIDE REAR CALIPER LEAKING |3.6.A.1| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings NEARSIDE FRONT CHASSIS LEG |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings OFFSIDE FRONT CHASSIS LEG |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings OFFSIDE REAR OUTER SILL CORRODED WITH IN 30CM OF SEATBELT MOUNTNG POINT |6.1.B.2| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill corroded and disguised with body-filler |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill corroded and disguised with body-filler |5.2.6| | 1 |
| Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded underbody sill |2.4.A.3| | 1 |
| Nearside Front Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Offside Front Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced end of sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings suspension component mounting |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings suspension component mounting |6.1.B.2| | 1 |
| Offside Rear Anti-roll bar damaged and seriously weakened Broken from ball joint |5.3.3 |b| |i|| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill. (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill. (5.3.6 (a) (i)) | 1 |
| Nearside Front Coil spring mounting fractured |5.3.1 |b| |i|| | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting CORRODED AND HOLED TO THE FRONT OF THE SUSPENSION TURRET (6.2.2 (d) (i)) | 1 |
| Exhaust shield missing where fitted as original equipment creating a risk of fire back box (6.1.3 (e)) | 1 |
| Nearside Front Side repeater incorrect colour on wing |1.4.A.2f| | 1 |
| Exhaust has a major leak of exhaust gases rear box joint |7.1.2| | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt on double wishbone |2.4.G.2| | 1 |
| Offside Rear Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt on double wishbone |2.4.G.2| | 1 |
| Coil spring fractured or broken NSF BROKEN |5.3.1 |b| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill / floor / inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill / floor / inner wheel arch (5.3.6 (a) (i)) | 1 |
| Service brake excessively fluctuating Both rears |1.2.1 |e|| | 1 |
| Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail above top arm and arb mount |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis rail above arb mount |2.4.A.3| | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wing (6.1.1 (c) (i)) | 1 |
| Offside Front Headlamps matched pair are incorrectly positioned |1.7.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength nr roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Tie bar/rod insecure |2.4.G.1| | 1 |
| Nearside Front Sub-frame corroded and seriously weakened on top |2.4.G.1| | 1 |
| Central Front Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill inner & outer |6.2.2 |d| |i|| | 1 |
| Nearside Front Power steering pipe/hose leaking pipe corroded |2.1.5 |a|| | 1 |
| Front Front position lamp|s| incorrect colour both sides blue |1.1.A.3e| | 1 |
| Offside Front Tie bar/rod attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Seat belt anchorage prescribed area is excessively corroded extensive corrosion to rear of off side sill / wheel arch area |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded extensive corrosion to front of near side rear inner wheel arch area |5.2.6| | 1 |
| Exhaust emits clearly visible black smoke during acceleration |7.3.A.2c| | 1 |
| Offside Front Steering rack damaged and unserviceable |2.2.C.1d| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded chassis rail |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases middle to rear joining |6.1.2 |a|| | 1 |
| Offside Front Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear Sub-frame attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Front Floor excessively deteriorated excessively corroded (6.2.4 (a) (i)) | 1 |
| Rear Floor excessively deteriorated boot floor excessively corroded both sides (6.2.4 (a) (i)) | 1 |
| Suspension component mounting prescribed area is inadequately repaired nearside rear inner and outer sill |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded near side rear inner sill |2.4.A.3| | 1 |
| Nearside Front Side repeater incorrect colour |4.4.3 |a|| | 1 |
| Offside Front Side repeater incorrect colour |4.4.3 |a|| | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Sill Front And Rear |6.1.1 |c| |i|| | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Sill Front And Rear |6.1.1 |c| |i|| | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Inner Wheel Arch |5.3.6 |a| |i|| | 1 |
| Steering retaining device missing |2.2.C.1g| | 1 |
| Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front Outer Body panel insecure Wing corroded |6.2.1 |a| |i|| | 1 |
| Rear Electrical wiring likely to drag on the ground Earth wire |4.11 |a| |iii|| | 1 |
| Front Brake lining(s) less than 1.5 mm thick (1.1.13 (a) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded inner wing area |2.4.A.3| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak mid and rear box (8.2.1.1 (b)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer (7.1.1 (a) (i)) | 1 |
| Nearside Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Coil spring corroded so that its cross sectional area is reduced and seriously weakened all-round (5.3.1 (b) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage cracked |2.4.G.1| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sarm |5.3.6 |a| |i|| | 1 |
| Offside Rear Rear reflector excessively damaged so that its function is impaired |1.5.1c| | 1 |
| Front Suspension arm pin or bush excessively worn x2 (5.3.4 (a) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting under sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting under sill (6.2.2 (d) (i)) | 1 |
| Power steering pipe/hose leaking corroded pipe (2.1.5 (a)) | 1 |
| Offside Front Vehicle structure has an inadequate repair which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Coil spring fractured or broken and nearside rear (5.3.1 (b) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.78% (8.2.1.2 (b)) | 1 |
| Rear Brake cable insecure | 1 |
| Offside Rear Floor excessively deteriorated boot floor (6.2.4 (a) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill under vehicle (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill and floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting lower wing holed and corroded (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor holed under vehicle (6.2.2 (d) (i)) | 1 |
| Power steering pipe/hose leaking power steering pipe corroded and leaking (2.1.5 (a)) | 1 |
| Offside Rear Hydraulic brake calliper damaged and braking performance affected mechanism seized |1.1.16 |a| |ii|| | 1 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis holed |2.4.A.3| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SILL AREA (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SILL AREA (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected CHASSIS RAIL (5.3.6 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Inner wheel arch |2.4.A.3| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced BOOT FLOOR |6.1.1 |c| |i|| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill corroded marked yellow |6.1.B.2| | 1 |
| Rear rear brake grabbing severely |3.7.A.5b| | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheelarch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting mid sill (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting underfloor inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch and by top shock absorber mount (6.2.2 (d) (i)) | 1 |
| Front Horn not working (7.7 (a) (ii)) | 1 |
| Nearside Front Outline marker lamp missing (4.2.1 (a) (ii)) | 1 |
| Offside Front Outline marker lamp missing (4.2.1 (a) (ii)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced between lower wing & outer chassis. (6.1.1 (c) (i)) | 1 |
| Emissions not tested engine running rough (8.2.1.2 (d)) | 1 |
| Nearside Rear Hydraulic brake calliper leaking from handbrake mechanism area (1.1.16 (b) (i)) | 1 |
| Offside Front Hydraulic brake calliper leaking from piston rubber seal area (1.1.16 (b) (i)) | 1 |
| Brake performance unable to be tested due to caliper leaks (1.2.1 (g)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL |5.3.6 |a| |i|| | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL |5.3.6 |a| |i|| | 1 |
| Headlamp aim not tested Not tested because O/S not working (4.1.2 (b)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer sill holed |5.2.6| | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill holed |6.1.B.2| | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill holed |6.1.B.2| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded body sill |2.4.A.3| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch/chassis |2.4.A.3| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch/chassis |2.4.A.3| | 1 |
| Front Front position lamp|s| not working both sides side lights |1.1.A.3b| | 1 |
| Nearside Front Upper Ball joint ball pin shank loose |2.2.B.1c| | 1 |
| Offside Front Upper Steering locking device missing |2.2.C.1g| | 1 |
| Statutory seat belt of the wrong type. |5.1.1| | 1 |
| Offside Front Power steering pipe/hose leaking |2.1.5 |a|| | 1 |
| Nearside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion sill end |6.1.C.1| | 1 |
| Offside Front Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Direction indicators adversely affected by the operation of another lamp all working at once |1.4.A.2h| | 1 |
| All direction indicators adversely affected by the operation of another lamp all |4.4.3 |b|| | 1 |
| Offside Front Brake disc fractured inner surface (1.1.14 (a) (ii)) | 1 |
| Brake disc in such a condition that it is seriously weakened both front and both rear (1.1.14 (a) (ii)) | 1 |
| Power steering component|s| leaking from rack |2.3.3b| | 1 |
| Nearside Front Power steering component|s| leaking steering rack |2.3.3b| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength as marked (5.3.6 (a) (i)) | 1 |
| Emissions not tested due to not holding revs at 3000 rpm fast idle and at idle
very irratic (8.2.1.2 (d)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is inadequately repaired sill patch repair not fully welded (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength patch repair not fully welded and still corrosion at front of patch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/arch badly corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing /arch badly corroded (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded at anti roll bar mount area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Service brake excessively binding after foot brake applied (1.2.1 (f)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing badly corroded under bonnet (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength centre chassis leg at front section (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill corroded marked in white |5.2.6| | 1 |
| Nearside Rear Brake hose excessively twisted |1.1.12 |b| |ii|| | 1 |
| Body has a sharp edge caused by corrosion offside nearside wheel arches ragged edges |6.1.C.1| | 1 |
| Fluid leak harmful to the environment or a risk to other road users Power steering fluid leak |8.4.1 |a| |i|| | 1 |
| Offside Front Electrical wiring insecure and connectors likely to become disconnected abs wiring (4.11 (a) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength door sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength door sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt x2 |5.3.4 |b| |ii|| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL BACK |6.1.B.2| | 1 |
| Offside Rear Braking system leaking BRAKE CALIPER |3.6.A.1| | 1 |
| Windscreen damaged and affecting the drivers view of the road crack on zone a (3.2 (a) (ii)) | 1 |
| Nearside Headlamp aim not tested dipped beam bulb out (4.1.2 (b)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting bottom of wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Brake lining|s| insecure |3.5.1g| | 1 |
| Nearside Front Body insecure and dangerous to other road users front wing inscure |6.1.B.1b| | 1 |
| Offside Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper coil spring fractured |2.4.C.1a| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength middle sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is fractured chassie leg in engine bay |2.4.A.3| | 1 |
| Parking brake inoperative on one side nearside rear not working |1.4.1 |a|| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing behind headlamp |6.1.B.2| | 1 |
| Offside Front Vehicle structure has a modification which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings lower sills |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings lower sill |6.1.B.2| | 1 |
| Nearside Front Lower Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings offside and nearside chassis corroded |6.1.B.2| | 1 |
| Offside Front Road wheel fractured |4.2.B.1a| | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer |6.1.2 |a|| | 1 |
| Rear Exhaust has a major leak of exhaust gases Flange/Join (6.1.2 (a)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch (5.3.6 (a) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis (6.2.2 (d) (i)) | 1 |
| Front Brake drum significantly and obviously worn both front badly pitted, and corroded |1.1.14 |a| |i|| | 1 |
| Offside Rear Anti-roll bar ball joint likely to become detached linkage has detached |5.3.4 |a| |ii|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill is excessively corroded, which has caused a large hole |5.3.6 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage severely distorted |2.4.G.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded closing panel |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg inner wheel arch area |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg inner wheel arch area |5.3.6 |a| |i|| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded arm |2.4.A.3| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area is excessively corroded arm |2.4.A.3| | 1 |
| Emissions not tested Due to exhaust blow |7.4.B.1| | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Hole in inner sill. (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Hole in boot. (battery tray) (6.2.2 (d) (i)) | 1 |
| Nearside Rear Upper Suspension arm fractured (5.3.3 (b) (ii)) | 1 |
| Offside Rear Upper Suspension arm likely to fail (5.3.3 (b) (ii)) | 1 |
| Nearside Rear Lower Suspension arm damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Windscreen damaged and affecting the driver`s view of the road crack |3.2 |a| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 1 |
| Nearside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Outer Vehicle structure inadequately repaired such that it is likely to adversely affect braking or steering (6.1.1 (d) (ii)) | 1 |
| Brake pipe connection leaking on a hydraulic braking system main brake pipe (1.1.11 (b) (ii)) | 1 |
| Nearside Steering locking device missing trackrod end (2.1.3 (d)) | 1 |
| Offside Steering locking device missing trackrod end (2.1.3 (d)) | 1 |
| Offside Front Upper Steering locking device missing ball joint (2.1.3 (d)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/wheel arch corroded & holed (6.1.1 (c) (i)) | 1 |
| Steering wheel rim loose (2.2.1 (c) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis leg (7.1.1 (a) (i)) | 1 |
| Offside Steering rack gaiter split (2.2.D.2d) | 1 |
| Dipswitch operation does not deflect all main beam headlamps to make them dipped beams (1.7.4b) | 1 |
| Nearside Front Suspension arm has excessive play in a pin/bush (2.4.G.2) | 1 |
| Offside Rear Suspension arm has excessive play in a pin/bush (2.4.G.2) | 1 |
| Offside Rear fog lamp not working (1.3.2b) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg rusty (5.3.6 (a) (i)) | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases Joint to silencer rotted (6.1.2 (a)) | 1 |
| Nearside Rear Exhaust emissions likely to be affected by an exhaust leak Joint to silencer rotted (8.2.1.1 (b)) | 1 |
| Offside Front Brake pipe excessively damaged metal pipe |1.1.11 |c|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill & sill end (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis inside wheel arch (Chalked) (5.3.6 (a) (i)) | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Offside Front Front drive shaft coupling is insecure |2.5.C.1c| | 1 |
| Emissions unable to be completed emissions high / catalytic converter missing (8.2.1.2 (d)) | 1 |
| Nearside Rear Floor excessively deteriorated outer sill (6.2.4 (a) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting CHASSIS LEG (6.2.2 (d) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Anti roll bar chassis mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings main chassis |6.1.B.2| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced o/s outer sill (7.1.1 (a) (i)) | 1 |
| Brake servo defective or ineffective (1.1.10 (a) (i)) | 1 |
| Drivers seat backrest cannot be secured in the upright position. (6.2.5 (b) (ii)) | 1 |
| Central Front Lower Undertray likely to become detached (6.2.1 (a) (ii)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg inside wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg inside wheel arch (6.2.2 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases BETWEEN JOINT OF CENTRE AND REAR SILENCER. |7.1.2| | 1 |
| Position lamp not working Both front |4.2.1 |a|| | 1 |
| Brake inadequately mounted Both front abs electrical looms |1.1.21 |c|| | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering front both chassis |6.1.1 |c| |ii|| | 1 |
| Offside Front Brake hose leaking on a hydraulic braking system Banjo fitting to caliper (1.1.12 (c) (ii)) | 1 |
| Nearside Front Brake hose leaking on a hydraulic braking system Banjo fitting to caliper (1.1.12 (c) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases Centre to rear silencer |6.1.2 |a|| | 1 |
| Exhaust has a major leak of exhaust gases Cat to centre section |6.1.2 |a|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg |6.1.1 |c| |i|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak Centre to Rear Joint |8.2.1.1 |b|| | 1 |
| Exhaust has a major leak of exhaust gases Centre to rear silencer joint (6.1.2 (a)) | 1 |
| Centre Rear Tie bar/rod attachment bracket/mounting insecure bolt missing out of underside brace |2.4.G.1| | 1 |
| Nearside Rear Tie bar/rod attachment bracket/mounting insecure bolt missing out of brace have chalked |2.4.G.1| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded CHASSIS RAIL |2.4.A.3| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage fractured |5.3.3 |b| |ii|| | 1 |
| Power steering component leaking rack housing (2.1.5 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill rust and filler (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill chassis hiled (7.1.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced near seat mount and belt mount (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar bracket mounting (5.3.6 (a) (i)) | 1 |
| Emissions not tested major leak (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 1 |
| Offside Rear Upper Tie bar/rod ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill areas |7.1.1 |a| |i|| | 1 |
| Rear Exhaust has a major leak of exhaust gases rear joint leaking (6.1.2 (a)) | 1 |
| Exhaust has a major leak of exhaust gases rear joint |6.1.2 |a|| | 1 |
| Offside Front Upper Suspension component ball joint likely to become detached no locking device fitted on securing nut (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill area |5.2.6| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength within prescribed area of o/s front subframe rear mounting (5.3.6 (a) (i)) | 1 |
| Power steering component leaking pipe leaking side of pump (2.1.5 (a)) | 1 |
| Offside Rear Coil spring fractured or broken at the top (5.3.1 (b) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch lineer (6.1.1 (c) (i)) | 1 |
| Nearside Front Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded/holed within 30cm of mounting point (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill corroded/holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded/holed within 30cm of mounting point (7.1.1 (a) (i)) | 1 |
| Nearside Body has a sharp edge caused by damage mirror head |6.1.C.1| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment adjusted rear calipers (1.1.6 (c)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded CHASSIE |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded CHASSIE |2.4.A.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases BROKEN |7.1.2| | 1 |
| Nearside Front position lamp|s| not working side light 501 |1.1.A.3b| | 1 |
| Brake pipe at imminent risk of failure or fracture 2x full length at rear presented greased (1.1.11 (a)) | 1 |
| Offside Front Anti-roll bar linkage attachment bracket/mounting fractured snapped |5.3.3 |b| |ii|| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` sat nav bracket |8.3.1e| | 1 |
| Nearside Front Anti-roll bar linkage insecurely attached broken (5.3.3 (a) (i)) | 1 |
| Nearside Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced chassis assy |2.4.G.1| | 1 |
| Offside Stop lamp obviously incorrectly positioned |1.2.1a| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill aea |5.2.6| | 1 |
| Emissions not tested engine over heat /water hose split and leak |7.3.A.1| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced BATTERY TRAY (6.1.1 (c) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases BOX JOINT (6.1.2 (a)) | 1 |
| Drivers airbag obviously inoperative (7.1.5 (c)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Nearside Lower Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded OUTER SILL |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill/rear quarter (7.1.1 (a) (i)) | 1 |
| Brake hydraulic reservoir fluid level decreases after several pedal applications |3.3.C.1| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wing area |2.4.A.3| | 1 |
| Nearside brake disc excessively scored |3.5.1h| | 1 |
| Central Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floorpan to outer sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill to floor pan (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill to floor pan (6.2.2 (d) (i)) | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` old tax disc |8.3.1e| | 1 |
| Offside Rear Brake hose bulging under pressure |3.6.B.3| | 1 |
| Offside Front Bumper damaged and likely to cause injury when grazed or contacted |6.1.4 |a| |i|| | 1 |
| Offside Front Body panel damaged and likely to cause injury numberplate mount |6.2.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill/inner wheel arch |7.1.1 |a| |i|| | 1 |
| Offside Front Body panel insecure lower edge corroded away. wing and arch liners not secure |6.2.1 |a| |i|| | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Offside Tie bar/rod attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Offside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Offside Headlamp does not operate immediately when selected on dipped beam |1.7.4a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis in front of top wishbone mounting. |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded in front of top wishbone mounting.also cracked. |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases back box to center |6.1.2 |a|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Steering locking device missing track rod end |2.2.C.1g| | 1 |
| Offside Rear Braking system leaking brake union/pipe |3.6.A.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases joints |7.1.2| | 1 |
| Emissions not tested tail pipe missing |7.4.B.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases box |6.1.2 |a|| | 1 |
| Steering system excessively rough rough when rotated from lock to lock. |2.2.D.1| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits high |7.3.D.3| | 1 |
| Offside Seat belt insecurely fixed to the seat buckle not mounted |5.2.1a| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer and inner sills |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer and inner sills |5.3.6 |a| |i|| | 1 |
| Nearside Front Wheel bearing rough when rotated noisey (5.1.3 (b) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in wheelarch (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases at manifold (6.1.2 (a)) | 1 |
| Emissions not tested excessive hc readings test aborted engine to hot test aborted |7.3.A.1| | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis near top arm mount (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cill (5.3.6 (a) (i)) | 1 |
| Rear Inner Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Position lamp not working all (4.2.1 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL... |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced INNER SILL... |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS,INNER WHEEL ARCH AREA (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ANTI ROLL BAR BRACKET AREA (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SILL (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WHEEL ARCH AREA (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced CHASSIS RAIL (6.1.1 (c) (i)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn LINK ARM BALL JOINT (5.3.4 (a) (i)) | 1 |
| Offside Rear Service brake excessively fluctuating disc |1.2.1 |e|| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill |5.3.6 |a| |ii|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 1 |
| Position lamp not working Both front (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill panel |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded body sill |5.2.6| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill
|2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis/floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill panel/floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill panel (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor pan (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill panel (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached fixing bolt too short and loose (5.3.4 (a) (ii)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Brake performance not tested brake pipe leaking (1.2.1 (g)) | 1 |
| Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected both sides chassis legs (5.3.6 (a) (ii)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis legs (5.3.6 (a) (i)) | 1 |
| Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis legs (6.2.2 (d) (i)) | 1 |
| Parking (secondary brake) on a single line braking system has inadequate effort at a wheel BOTH SIDES (1.3.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Offside Front Body insecure wing (6.2.2 (a) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering wheel arch |6.1.1 |c| |ii|| | 1 |
| Offside Front Brake hose excessively stretched |1.1.12 |b| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg, engine bay (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected as marked (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected as marked (5.3.6 (a) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced as marked (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced as marked (7.1.1 (a) (i)) | 1 |
| Offside Headlamp aim beam image obviously incorrect dip |1.8.A.1b| | 1 |
| Centre Upper Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill closing panel |7.1.1 |a| |i|| | 1 |
| Emissions unable to be completed engine misfire (8.2.1.2 (d)) | 1 |
| Front Headlamp aim unable to be tested n/s o/s (4.1.2 (b)) | 1 |
| Nearside Rear Upper Suspension arm pin or bush excessively worn wishbone bush |5.3.4 |a| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Seat belt mounting (rear sill) (6.1.1 (c) (i)) | 1 |
| Offside Front Rear fog lamp not working |1.3.2b| | 1 |
| Steering column retaining device missing |2.1.6| | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak pipe (8.2.1.1 (b)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section - viewed from underside |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section viewed inside wheel arch |5.3.6 |a| |i|| | 1 |
| Steering system has excessive free play detected at the steering wheel |steering rack fitted| nearside inner rack end/tie rod |2.2.A.1b| | 1 |
| Power steering component|s| leaking nearside of rack from bellows |2.3.3b| | 1 |
| Service brake excessively binding both rears 30kg (1.2.1 (f)) | 1 |
| Service brake excessively fluctuating rears 40kgf (1.2.1 (e)) | 1 |
| Exhaust has a major leak of exhaust gases Centre Section (6.1.2 (a)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassi leg |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassi leg |2.4.A.3| | 1 |
| Offside Rear Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis rail mounting (5.3.3 (b) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis rail mounting (5.3.3 (b) (i)) | 1 |
| Nearside Front Anti-roll bar linkage synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings marked in red paint |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings marked in red paint |6.1.B.2| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both front chassis legs (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill |7.1.1 |a| |i|| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Brake disc significantly and obviously worn inner surface (1.1.14 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn inner surface (1.1.14 (a) (i)) | 1 |
| Nearside Front Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis rail badly corroded |6.1.A.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis rail badly corroded |6.1.A.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer body sill badly corroded |5.2.6| | 1 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Parking brake mechanism/associated mounting prescribed area is fractured |3.1.9| | 1 |
| Nearside Rear Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both sides (4.1.4 (b)) | 1 |
| Front Service brake grabbing severely and rear (1.2.1 (c)) | 1 |
| Emissions not tested Engine running badly unable to maintain revs (8.2.1.2 (d)) | 1 |
| Wheel nut|s| missing all |4.2.A.1e| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill ( marked ) (5.3.6 (a) (i)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction Sun strip on top of screen (3.1 (a) (ii)) | 1 |
| Hydraulic fluid leaking continuously posing a serious risk to road safety (8.4.1 (a) (ii)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed |6.2.2 |d| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed |6.2.2 |d| |i|| | 1 |
| Brake performance not tested due to osr caliper leaking |3.7.A.1| | 1 |
| Nearside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Suspension component mounting prescribed area excessively damaged significantly reducing structural strength both rear inner sills (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension arm insecure and impairing directional stability bolt. nut was missing and bolt loose (5.3.3 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Outer sill (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Inner sill (5.3.6 (a) (ii)) | 1 |
| Rear Anti-roll bar linkage ball joint excessively worn both (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch on chassis (5.3.6 (a) (i)) | 1 |
| Rear fog lamp obviously incorrectly positioned |4.5.4 |a|| | 1 |
| Nearside Front Shock absorber insecure top mount |2.7.2b| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis leg (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floorpan (6.2.2 (d) (i)) | 1 |
| Front Headlamps matched pair are incorrectly positioned |1.7.3| | 1 |
| Emissions not tested due to major exhaust blow |7.3.A.1| | 1 |
| Central Rear Exhaust has a major leak of exhaust gases back box |7.1.2| | 1 |
| Central Front Horn not working |1.6.2a| | 1 |
| Seat belt anchorage prescribed area is excessively corroded both outer seals |5.2.6| | 1 |
| Offside Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Offside Front Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Headlamp aim not tested unable top switch full beam to dipped (4.1.2 (b)) | 1 |
| Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded door sill |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded door sill |5.2.6| | 1 |
| Offside Rear Braking system leaking calliper. leaking from handbrake lever seal. |3.6.A.1| | 1 |
| Exhaust has a major leak of exhaust gases from back box |7.1.2| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced FLOOR (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear box |6.1.2 |a|| | 1 |
| Nearside Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 1 |
| Nearside Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer sill |6.2.2 |d| |i|| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis Leg (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Coil spring not correctly located |2.4.C.2| | 1 |
| Offside Rear Lower Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases middle to rear joint corroded & blowing to excess. (6.1.2 (a)) | 1 |
| Steering rack has excessive free play detected at the steering wheel |steering rack fitted| Nearside tie rod |2.3 |a| |i|| | 1 |
| Nearside Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Brake hydraulic reservoir fluid not visible (1.1.10 (d) (iii)) | 1 |
| Front Horn sound not in accordance with requirements (7.7 (c)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed and coroded |7.1.1 |a| |i|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed and corroded |7.1.1 |a| |i|| | 1 |
| Nearside Front Lower Shock absorbers has an excessively worn bush |5.3.2 |c|| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired Body filler found |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired Body filler found |2.4.A.3| | 1 |
| Power steering pipe|s| or hose|s| leaking pipe from rack |2.3.3b| | 1 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer body sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS RAIL |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WHEEL ARCH |5.3.6 |a| |i|| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both sides rear outer sills corroded |6.1.B.2| | 1 |
| Exhaust has a major leak of exhaust gases catalyst to centre joint (6.1.2 (a)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting has been repaired before |6.2.2 |d| |i|| | 1 |
| Service brake effort inadequate at a wheel both rear (1.2.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill |6.1.1 |c| |i|| | 1 |
| Offside Front Front position lamp|s| not working dip beam bulb |1.1.A.3b| | 1 |
| Exhaust has a major leak of exhaust gases at catalytic converter (6.1.2 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner and outer sill (6.2.2 (d) (i)) | 1 |
| All position lamps adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Headlamp not working on dipped beam Both (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill. (7.1.1 (a) (i)) | 1 |
| Steering wheel has movement relative to the column indicating looseness (2.2.1 (a) (i)) | 1 |
| Suspension arm mounting modified so the suspension is inoperative all split pins missing from castle nuts on all suspension ball joints upper and lower (5.3.3 (c) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases centre and rear exhaust sections blowing at sealing flange |7.1.2| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded outer sill area |2.4.A.3| | 1 |
| Rear Torque/reaction arm attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Offside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Inner sill. (6.2.2 (d) (i)) | 1 |
| Nearside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement front |2.4.G.2| | 1 |
| Nearside Front Macpherson strut modified so the suspension is likely to fail other components spring adjuster locking nut loose (5.3.3 (c) (ii)) | 1 |
| Offside Front Macpherson strut modified so the suspension is likely to fail other components spring adjuster locking nut loose (5.3.3 (c) (ii)) | 1 |
| Nearside Headlamp light source and lamp not compatible led (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible led (4.1.4 (c)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction wiper (3.1 (a) (ii)) | 1 |
| Offside Front Macpherson strut has excessive play in the sliding bush or gland (2.5.B.1b) | 1 |
| Nearside Rear brake caliper leaking (3.6.A.1) | 1 |
| Central Exhaust has a major leak of exhaust gases joint (6.1.2 (a)) | 1 |
| Offside Rear fog lamp does not emit a steady red light (1.3.2e) | 1 |
| Oil leaking excessively from transmission cooler pipes (8.4.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure body mounts (5.3.3 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn lock nut loose (5.3.4 (a) (i)) | 1 |
| Offside Rear coil spring incomplete (2.4.C.1a) | 1 |
| Nearside Rear brake disc excessively scored (3.5.1h) | 1 |
| Offside Rear brake disc excessively scored (3.5.1h) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced X2 (7.1.1 (a) (i)) | 1 |
| Brake performance unable to be tested Due to rear pads (1.2.1 (g)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill end (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill end (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill to floor (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering anti roll bar mounting area |6.1.1 |c| |ii|| | 1 |
| Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill area various places |6.1.1 |c| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheelarch /sill (7.1.1 (a) (i)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak silencer blowing (8.2.1.1 (b)) | 1 |
| Nearside Rear Suspension component has an unsafe modification (5.3.3 (c) (i)) | 1 |
| Offside Rear Suspension component has an unsafe modification (5.3.3 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting JACKING POINT (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting JACKING POINT (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch (6.2.2 (d) (i)) | 1 |
| Rear fog lamp does not emit a steady red light white lens (4.5.4 (a)) | 1 |
| Nearside Front Inner Steering rack gaiter missing or no longer prevents the ingress of dirt boot split (2.1.3 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases drilled exhaust silencer (6.1.2 (a)) | 1 |
| Front Shock absorbers has negligible damping effect x 2 (5.3.2 (d)) | 1 |
| Rear Shock absorbers has negligible damping effect x 2 (5.3.2 (d)) | 1 |
| Front Lower Shock absorbers insecurely attached x2 bolts no locking devise (5.3.2 (a) (i)) | 1 |
| Valve stem seriously damaged All |5.2.3 |j|| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Front Steering rack gaiter split (2.2.D.2d) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Headlamp not working on main beam (1.7.5a) | 1 |
| Rear fog lamp tell tale not working (1.3.1b) | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill corroded and holed within 30cms of roll cage mount which has seatbelt attached (5.2.6) | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill/floor pan corroded and holed within 30cms of roll cage mount which has seatbelt attached (5.2.6) | 1 |
| Exhaust emissions carbon monoxide content excessive (7.3.B.1a) | 1 |
| Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4) | 1 |
| Nearside Front Macpherson strut worn and seriously weakened (2.4.G.2) | 1 |
| Headlamp missing both (4.1.1 (a) (ii)) | 1 |
| Subframe mounting prescribed area excessively damaged significantly reducing structural strength boot floor missing (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill repair inadequate (7.1.1 (a) (i)) | 1 |
| Central Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 1 |
| Rear fog lamp switch missing (4.5.3 (a) (ii)) | 1 |
| Offside Rear Brake inadequately mounted touching wheel (1.1.21 (c)) | 1 |
| Body component damaged and likely to cause injury rear off body has sharps edges likely to cause injury (6.2.1 (a) (i)) | 1 |
| Nearside Front Suspension arm modified so the suspension is likely to foul other components touching anti roll bar (5.3.3 (c) (ii)) | 1 |
| Offside Front Suspension arm modified so the suspension is likely to foul other components touching anti roll bar (5.3.3 (c) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner floor /inner sill (7.1.1 (a) (i)) | 1 |
| Central Stop lamp(s) light intensity significantly reduced (4.3.3 (a) (ii)) | 1 |
| Offside Stop lamp(s) adversely affected by the operation of another lamp Bulb fitted incorrectly? (4.3.3 (b)) | 1 |
| Offside Position lamp adversely affected by the operation of another lamp Bulb fitted incorrectly? (4.2.3 (c)) | 1 |
| Nearside Power steering pipe/hose leaking To front cooling pipe (2.1.5 (a)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt Boot split (2.1.3 (g) (ii)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt Boot split (2.1.3 (g) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired Outer sill cracked away from jacking point/inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail within 30cm of subframe mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Front Upper Suspension arm attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Offside Front Upper Suspension arm attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Front Front passenger door catch insecure (6.2.3 (c) (ii)) | 1 |
| Offside Rear fog lamp lens defective such that emitted light is adversely affected light is pink not red (4.5.1 (b) (ii)) | 1 |
| Central Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner arch (7.1.1 (a) (i)) | 1 |
| Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Rear Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Hazard warning lamps inoperative all (4.4.1 (e)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced FLOOR PAN CORRODED (7.1.1 (a) (i)) | 1 |
| Steering wheel rim loose Mounting bolts loose (2.2.1 (c) (i)) | 1 |
| Nearside Front Direction indicator obviously incorrectly positioned (4.4.3 (a)) | 1 |
| Offside Front Direction indicator obviously incorrectly positioned (4.4.3 (a)) | 1 |
| Front Windscreen in an unacceptable condition (3.2 (c) (i)) | 1 |
| Offside Front Body component damaged and likely to cause injury wheel arch moulding (6.2.1 (a) (i)) | 1 |
| Central Front Exhaust has a major leak of exhaust gases join (6.1.2 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassi rail (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch to inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is inadequately repaired arch (5.3.6 (a) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases join (6.1.2 (a)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Suspension arm mount (5.3.6 (a) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Hole/crack in chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Subframe mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Subframe mount (5.3.6 (a) (i)) | 1 |
| Rear fog lamp does not emit a steady red light White light (4.5.4 (a)) | 1 |
| Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch area (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/arch area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/arch area (5.3.6 (a) (i)) | 1 |
| Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt both sides (2.1.3 (g) (ii)) | 1 |
| Offside Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 1 |
| Nearside Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Emissions unable to be completed exhaust blowing (8.2.1.2 (d)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis rail marked in chalk (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Chassis rail (7.1.1 (a) (i)) | 1 |
| Offside Front Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded floor pan |2.4.A.3| | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Front Brake hose connection leaking on a hydraulic braking system calliper (1.1.12 (c) (ii)) | 1 |
| Emissions not tested cat missing (8.2.1.2 (d)) | 1 |
| Emissions unable to be completed excessive exhaust leak of gases (8.2.1.2 (d)) | 1 |
| Brake lever has insufficient reserve travel Park brake lever (1.1.2 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill corroded (7.1.1 (a) (i)) | 1 |
| Front Exhaust shield missing where fitted as original equipment creating a risk of fire (6.1.3 (e)) | 1 |
| Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre joint (6.1.2 (a)) | 1 |
| Steering wheel rim fractured (2.2.1 (c) (i)) | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen no discernible beam pattern |4.1.2 |a|| | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen no discernible beam pattern |4.1.2 |a|| | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer holed and blowing |6.1.2 |a|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill,as marked |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill back,as marked |7.1.1 |a| |i|| | 1 |
| Offside Rear Body has a projection caused by damage bumper insecure |6.1.C.1| | 1 |
| Offside Upper Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Nearside Front Position lamp missing (4.2.1 (a) (ii)) | 1 |
| Offside Front Position lamp missing (4.2.1 (a) (ii)) | 1 |
| Headlamp light source and lamp not compatible LED lamps fitted (4.1.4 (c)) | 1 |
| Offside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis (5.3.6 (a) (ii)) | 1 |
| Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Front Drivers seat moving inadvertently (6.2.5 (b) (ii)) | 1 |
| Rear Inner Anti-roll bar pin or bush excessively worn d bushes, o/s and n/s,, ,recommend replace (5.3.4 (a) (i)) | 1 |
| Emissions not tested co and lamda high but started to overheat/loose water aborted test (8.2.1.2 (d)) | 1 |
| Nearside Rear Shock absorbers likely to become detached shock bolt loose (5.3.2 (a) (ii)) | 1 |
| Offside Front Anti-roll bar linkage likely to become detached bolt loose (5.3.3 (a) (ii)) | 1 |
| Offside Front Shock absorbers likely to become detached shock bolt loose (5.3.2 (a) (ii)) | 1 |
| Central Front Position lamp not working both not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (chalked) (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch/outer sill (chalked) (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure is fractured and structural rigidity is significantly reduced chassis rail split (6.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor under drivers seat (7.1.1 (a) (i)) | 1 |
| Central Rear Brake pipe at imminent risk of failure or fracture (1.1.11 (a)) | 1 |
| Nearside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Rear Brake disc significantly and obviously worn N/S & O/S (1.1.14 (a) (i)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements No tell tail light. (4.5.3 (a)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements Tell Tale Light Not Working (4.5.3 (a)) | 1 |
| Nearside Front suspension has a suspension lower ball joint securing nut not locked |2.5.B.1a| | 1 |
| Sub-frame damaged and seriously weakened subframe cracked marked white (5.3.3 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill corroded |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill corroded |5.2.6| | 1 |
| Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg in arch and underneath by D bush mountings |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg in arch and underneath by D bush mountings |5.3.6 |a| |i|| | 1 |
| Emissions not tested overheated (8.2.1.2 (d)) | 1 |
| Offside Front Suspension component corroded and seriously weakened chassis leg |5.3.3 |b| |i|| | 1 |
| Nearside Front Upper Suspension arm insecurely attached Split pin missing through the ball joint (5.3.3 (a) (i)) | 1 |
| Offside Front Upper Suspension arm insecurely attached Split pin missing through the ball joint (5.3.3 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill panel to rear lower wheel arch |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill panel corroeded around previous repair |5.2.6| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Nearside front chassis leg corroded. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Tie bar/rod fractured |2.4.G.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill area |7.1.1 |a| |i|| | 1 |
| Offside Rear Brake hose leaking union to caliper |3.6.A.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill area (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS RAIL UNDER WHEEL ARCH (5.3.6 (a) (i)) | 1 |
| Power steering pipe/hose leaking UNDER BONNET (2.1.5 (a)) | 1 |
| Nearside Rear Inner Road wheel badly distorted BEAD (5.2.2 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill to inner wheel arch area (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Vehicle structure inadequately repaired such that structural rigidity is significantly reduced chassis rail under wheel arch (6.1.1 (d) (i)) | 1 |
| Stop lamp not working centre rear |1.2.1b| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Hydraulic fluid leaking excessively Steering rack (8.4.1 (a) (i)) | 1 |
| Brake performance not tested Due To Rigid Brake Line Leak (1.2.1 (g)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded door sill
|5.2.6| | 1 |
| Emissions not tested exhaust blowing |7.3.A.1| | 1 |
| Emissions not tested due to exhaust blowing to excess (8.2.1.2 (d)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing adjacent to anti roll bar and sub-frame mounting. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Nearside Rear Integral body structure has excessive corrosion which adversely affects braking or steering inner sill (6.1.1 (c) (ii)) | 1 |
| Nearside All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Lower Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill area (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill / arch (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded/hole (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill area. |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill marked in yellow |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill marked in yellow |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension arm corroded and seriously weakened both upper and lower wishbones corroded (5.3.3 (b) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassic |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassic |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded SILL |2.4.A.3| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits EXHAUST BLOW |8.2.1.2 |c|| | 1 |
| Main beam tell-tale not working BLUE LIGHT ON DASH |4.9.1 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Upper chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Upper chassis leg (5.3.6 (a) (i)) | 1 |
| Stop lamp|s| not working nearside |4.3.1 |a| |ii|| | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting nearside front |6.2.2 |d| |i|| | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting offside front |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floorpan (6.1.1 (c) (i)) | 1 |
| Offside Rear Anti-roll bar ball joint likely to become detached drop link ball joint not attached (5.3.4 (a) (ii)) | 1 |
| Offside Outer Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Subframe mounting prescribed area excessively corroded significantly reducing structural strength Floor |5.3.6 |a| |i|| | 1 |
| Rear Electrical wiring damaged, likely to cause a short |1.9.2b| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch area (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill has been spot welded not seem welded (7.1.1 (a) (i)) | 1 |
| Nearside Front Body has a projection caused by damage |6.1.C.1| | 1 |
| Offside Front Road wheel badly damaged |4.2.A.1a| | 1 |
| Nearside Rear Coil spring fractured or broken at upper coil |5.3.1 |b| |i|| | 1 |
| Offside Front Braking system leaking Bleed nipple not tightened, and spanner still attached |3.6.A.1| | 1 |
| Offside Front Road wheel badly distorted (5.2.2 (c) (i)) | 1 |
| Nearside Front Road wheel badly distorted |5.2.2 |c| |i|| | 1 |
| Nearside Rear Road wheel badly distorted (5.2.2 (c) (i)) | 1 |
| Offside Front Service brake excessively binding wheel cant be turned by hand, excessive binding (1.2.1 (f)) | 1 |
| Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Anti-roll bar mounting modified so the suspension is likely to fail other components touching spring ,relocated (5.3.3 (c) (ii)) | 1 |
| Offside Front Brake performance not tested pad on metal (1.2.1 (g)) | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Offside Side repeater incorrect colour |4.4.3 |a|| | 1 |
| Central Exhaust fumes causing a danger to health of persons on board (6.1.2 (b) (ii)) | 1 |
| Offside Front Anti-roll bar corroded and seriously weakened chassis leg holed 30 cm from anti roll bar mount (5.3.3 (b) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak manifold area? (8.2.1.1 (b)) | 1 |
| Offside Front Position lamp missing |4.2.1 |a|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Under sill damaged and corroded. (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
| Nearside Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed and corroded (6.1.1 (c) (i)) | 1 |
| Offside Front Brake hose damaged and likely to fail (1.1.12 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch (5.3.6 (a) (i)) | 1 |
| Brake pipe leaking on a hydraulic braking system front to rear pipe (1.1.11 (b) (ii)) | 1 |
| Fuel cap/sealing device mounting flange/sealing method defective |7.2.4c| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch creeping behind arch lining (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch on chassis rail, next to D bush mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt damaged |7.1.2 |b| |i|| | 1 |
| Front Position lamp not working near side and off side (4.2.1 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Centre section to back box (6.1.2 (a)) | 1 |
| Emissions not tested Vehicle cutting out before cat test could be completed. (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion sill section within prescribed area, seat belt mount. |7.1.1 |a| |i|| | 1 |
| Brake pipe leaking on a hydraulic braking system Front to rear pipe (1.1.11 (b) (ii)) | 1 |
| Power steering component leaking Nearside of engine area (appears to be from a pipe) (2.1.5 (a)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Corrosion near n/s/f upper arm on chassis leg. (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Corrosion near upper arm on the side of the chassis leg (5.3.6 (a) (i)) | 1 |
| Electrical wiring insecure earth cable broken on the rear diff |1.9.2a| | 1 |
| Offside Front Shock absorber has negligible damping effect |2.7.5| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis/ Anti roll bar mounting point (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis/ Anti roll bar mounting (5.3.6 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill, corroded and filled (body filler) (7.1.1 (a) (i)) | 1 |
| Nearside Front Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill has hole |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill has hole |6.1.B.2| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded rear sill |5.2.6| | 1 |
| Nearside Rear Exhaust system not adequately supported silencer support bracket broken |7.1.1| | 1 |
| Offside Rear Upper Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear Coil spring fractured or broken suspension (5.3.1 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/chassis rail forward section excessively corroded within 30 cms of front suspension anti-roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/chassis rail forward section excessively corroded within 30cms of front suspension anti-roll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill section excessively corroded within 30cms of front passenger lower seat belt anchorage (7.1.1 (a) (i)) | 1 |
| Nearside Track rod end ball joint has excessive play steering (2.1.3 (b) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases tail section missing |6.1.2 |a|| | 1 |
| Rear Exhaust has a major leak of exhaust gases part missing |6.1.2 |a|| | 1 |
| Rear Exhaust silencer insecure mounting bracket broken away |8.1.1 |b| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced CHASSIS (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced CHASSIS (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced OUTTER CILL (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced OUTTER CILL (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail in wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail in wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Floor pan damaged and corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner arch/inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt locking mechanism does not secure or release UNDER LOAD |5.2.5a| | 1 |
| Offside Front Seat belt locking mechanism does not secure or release UNDER LOAD |5.2.5a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis under wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced lower outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Electrical wiring likely to touch hot or rotating parts |4.11 |a| |iii|| | 1 |
| Front Exhaust has a major leak of exhaust gases clamp (6.1.2 (a)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting hole in boot (6.2.2 (d) (i)) | 1 |
| Offside Body insecure sill inner and outer (6.2.2 (a) (i)) | 1 |
| Nearside Body insecure inner and sills (6.2.2 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill x2 |7.1.1 |a| |i|| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded body sill corroded/holed |5.2.6| | 1 |
| Horn sound not in accordance with requirements |7.7 |c|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer body sill corroded/holed within 30cm of osr seat/seat belt mounting (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp lens seriously defective and offside (4.1.1 (b) (ii)) | 1 |
| Power steering component insecure power steering fluid reservoir (2.1.5 (d) (i)) | 1 |
| Offside Rear Upper Suspension arm pin or bush excessively worn to wheel hub attachment (5.3.4 (a) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill (6.2.2 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Rear and centre exhaust joint excessively corroded and deteriorated |7.1.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Anti-roll bar linkage has excessive play in a ball joint front and rear nearside and offside |2.4.G.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill return/floor pan (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Offside Front brake caliper leaking leaking at banjo |3.6.A.1| | 1 |
| Offside Front Service brake indicates brake bind Binding when rotated |3.7.D.2a| | 1 |
| Nearside Rear Service brake indicates brake bind Binding when rotated |3.7.D.2a| | 1 |
| Offside Rear Hydraulic fluid leaking excessively |8.4.1 |a| |i|| | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |3.3 |b| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area fractured significantly reducing structural strength +corroded (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area fractured significantly reducing structural strength + corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded REAR OUTERSILL |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wing (5.3.6 (a) (i)) | 1 |
| Offside Front Brake hose excessively damaged |1.1.12 |b| |ii|| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment excessive travel |1.1.6 |c|| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings N/S AND O/S OUTER SILLS |6.1.B.2| | 1 |
| Nearside Rear Fuel system component leaking |7.2.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill backing |2.4.A.3| | 1 |
| Drivers door likely to open inadvertently or not remain closed (6.2.3 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch area (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect poss lens (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect poss lens (4.1.2 (c)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired chassis. Not continuous seam weld (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired chassis. Not continuous seam weld (5.3.6 (a) (i)) | 1 |
| Nearside Front Front position lamp|s| not working REPLACE N/S F SIDELAMP BULB |1.1.A.3b| | 1 |
| Front Windscreen wiper not working |3.4 |a|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Brake performance not tested due to n/s/r suspension arm (1.2.1 (g)) | 1 |
| Offside Front Hydraulic brake calliper leaking From nipple (1.1.16 (b) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill excessively corroded (7.1.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases backbox |7.1.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill/arch |7.1.1 |a| |i|| | 1 |
| Nearside Front Outer Steering locking device missing track rod end (2.1.3 (d)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill rusted. (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill rusted (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed and corroded (6.2.2 (d) (i)) | 1 |
| Offside Rear Hydraulic brake calliper leaking brake calliper (1.1.16 (b) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill insufficient repair and corroded |7.1.1 |a| |i|| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill areas (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill areas (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage insecurely attached Nut loose (5.3.3 (a) (i)) | 1 |
| Nearside Rear Upper Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower sill |5.3.6 |a| |i|| | 1 |
| Centre Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt Both (5.3.4 (b) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both front chassis at anti roll bar mounts (5.3.6 (a) (i)) | 1 |
| Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s and n/s rear sills inner and outer seriously corroded and falling apart (6.2.2 (d) (i)) | 1 |
| Nearside Rear Braking system leaking brake pipe |3.6.A.1| | 1 |
| Offside Front Lower Body component insecure wing corroded/ loose/ not secure (6.2.1 (a) (i)) | 1 |
| Emissions unable to be completed major exhaust leak/emission control equipment missing (8.2.1.2 (d)) | 1 |
| Offside Rear Floor excessively deteriorated sill (6.2.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis under wheel arch (5.3.6 (a) (i)) | 1 |
| Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Outer Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill and wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail |6.1.1 |c| |i|| | 1 |
| Nearside Front Upper Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Front Front position lamp|s| not working side light |1.1.A.3b| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill section (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill section (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings boot floor |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings boot floor |6.1.B.2| | 1 |
| Seat belt anchorage prescribed area is excessively corroded o s and n s |5.2.6| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer chassis leg corroded and holed |6.1.B.2| | 1 |
| Exhaust has a major leak of exhaust gases join broken between centre and rear section |6.1.2 |a|| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected outer sill corroded to excess (5.3.6 (a) (ii)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill corroded and detached from structure (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis - inside wheel arch - outer face |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis - inside wheel arch - lower face |2.4.A.3| | 1 |
| Nearside Front Lower brake caliper securing device loose |3.5.1j| | 1 |
| Subframe mounting prescribed area is excessively corroded Front o/s and n/s chassis legs |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded Front anti roll bar mountings o/s and n/s |2.4.A.3| | 1 |
| front brake binding o/s and n/s |3.7.B.1| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Rear end of the n/s sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis bottom by anti roll bar mount |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis bottom by anti roll bar mount |5.3.6 |a| |i|| | 1 |
| Nearside Front Outer Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Nearside Front Outer Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail |anti roll bar mount| |2.4.A.3| | 1 |
| Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Front subframe front mountings (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases REAR SILENCER |7.1.2| | 1 |
| Offside Rear Hydraulic brake calliper leaking weeping from park brake ratchet mechanism and slightly binding (1.1.16 (b) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill. (7.1.1 (a) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill as marked. (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Body panel corroded and likely to cause injury Sill. (6.2.1 (a) (i)) | 1 |
| Central Brake modification unsafe Front to rear brake pipe unions. (1.1.21 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill edge (5.3.6 (a) (i)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (High) (8.2.1.2 (c)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced to rear outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail next to anti roll bar mounting point (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 1 |
| Offside Front Hydraulic brake calliper damaged Wheel extremely tight (1.1.16 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chasse leg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chasse leg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both front chassis legs (6.1.1 (c) (i)) | 1 |
| Nearside Outer Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint not attached |2.4.G.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired Outer sill (5.3.6 (a) (i)) | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering nearside outer sill holed multiple places |6.1.1 |c| |ii|| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering offside outer sill holed multiple places |6.1.1 |c| |ii|| | 1 |
| Headlamp not working on dipped beam offside |4.1.1 |a| |ii|| | 1 |
| Offside Front Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis x2, marked yellow |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis, marked yellow |5.3.6 |a| |i|| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer body sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch |5.3.6 |a| |i|| | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Chassis leg (6.2.2 (d) (ii)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded Outer bodysill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis rail near Anti-roll bar mounting. |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis rail near Anti-roll bar mounting. |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis - anti roll bar mountain (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer Sill Area |7.1.1 |a| |i|| | 1 |
| Offside Rear Brake hose connection leaking on a hydraulic braking system onto caliper (1.1.12 (c) (ii)) | 1 |
| Front Horn not working |1.6.2a| | 1 |
| Service brake: efficiency below requirements |3.7.D.4| | 1 |
| Offside Front Upper Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg excessively corroded, next to upper suspension mounting (6.2.2 (d) (i)) | 1 |
| Emissions unable to be completed due to exhaust leak and a after market (loud) back box (8.2.1.2 (d)) | 1 |
| Rear Brake performance unable to be tested (1.2.1 (g)) | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired outer sill |5.2.6| | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail inner wheel arch area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel (7.1.1 (a) (i)) | 1 |
| Nearside Rear Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
| Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt boot detached/deteriorated (5.3.4 (b) (ii)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt boot detached/deteriorated (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Position lamp lens seriously defective Bringing indicator on at the same time |4.2.1 |b|| | 1 |
| Service brake lagging in operation |1.2.1 |d|| | 1 |
| Anti-roll bar ball joint excessively worn Both rears (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar corroded and seriously weakened drop-link |2.4.G.1| | 1 |
| Offside Front Anti-roll bar corroded and seriously weakened drop-link |2.4.G.1| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened multiple areas (5.3.3 (b) (i)) | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint Drop link
|2.4.G.2| | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt bottom balljoint
|2.4.G.2| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor has large hole in (6.1.1 (c) (i)) | 1 |
| Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength both sides chassis |5.3.6 |a| |i|| | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced both sides chassis |6.1.1 |c| |i|| | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded and holed |6.1.1 |c| |i|| | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded and holed |6.1.1 |c| |i|| | 1 |
| Offside Front Steering system fouling fowling undertray (2.1.4 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |subframe mounting| |5.3.6 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Bottom And Side Chassis Rail (5.3.6 (a) (i)) | 1 |
| Offside Rear Hydraulic fluid leaking excessively Brake caliper |8.4.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both rear sills |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension arm fractured |5.3.3 |b| |ii|| | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front Lower Macpherson strut mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting body/chassis |6.2.2 |d| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength LEG (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength LEG (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg area (5.3.6 (a) (i)) | 1 |
| Front Body component likely to become detached bumper (6.2.1 (a) (ii)) | 1 |
| Hazard warning switch missing |1.4.B.1d| | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis under wheelhouse (6.1.1 (c) (i)) | 1 |
| Front position lamp|s| has a product on the light source so it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill, multiple points |7.1.1 |a| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis around anti roll bar mounting area |6.1.1 |c| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting area of chassis in wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp flickers when tapped lightly by hand |1.2.4c| | 1 |
| Exhaust has a major leak of exhaust gases at joint between centre and rear exhaust sections |7.1.2| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both cills rear (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded Nsr outer sill area. |5.2.6| | 1 |
| Headlamp not working on dipped beam Nsf. |1.7.5a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength main chassis member above front subframe mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength main chassis member above front subframe mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Offside Front Outer Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis area /anti roll bar mounting area (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis and anti roll bar area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area near subframe mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area near subframe mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under sill and floor (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill and o/s rear inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Front Steering rack insecure |2.2.B.1a| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings off side outer sill |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL AND INNER ARCH (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced UPPER ARCH (7.1.1 (a) (i)) | 1 |
| Power steering pipe/hose corroded such that the steering is adversely affected (2.1.5 (g) (ii)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced body sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body sill |5.3.6 |a| |i|| | 1 |
| Central Rear Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases at flange |6.1.2 |a|| | 1 |
| Nearside Front Body has a projection caused by damage bumper |6.1.C.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength outer sill |2.4.A.3| | 1 |
| Offside Front Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassi leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Corrosion to chassis within 30cm of suspension component (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded within 30cm of seat belt mount (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired chassis leg (6.2.2 (d) (ii)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired chassis leg (6.2.2 (d) (ii)) | 1 |
| Offside Rear Body component damaged and likely to cause injury light lens (6.2.1 (a) (i)) | 1 |
| Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner chassis leg (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed test aborted due to readings clearly in excess of requirements (8.2.1.2 (d)) | 1 |
| Braking system leaking nearside rear brake caliper leaking |3.6.A.1| | 1 |
| Nearside Rear Suspension rod insecure and impairing directional stability link rod |5.3.3 |a| |ii|| | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt Split (2.1.3 (g) (ii)) | 1 |
| Nearside front brake recording little or no effort nearside reading half offside |3.7.B.5a| | 1 |
| Brake lever has insufficient reserve travel parking brake |1.1.2 |a|| | 1 |
| Offside Front Lower Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced sill (6.1.1 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected frame rail (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected frame rail (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected boot floor (5.3.6 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength footwell (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Front suspension ball joint dust cover missing |2.4.G.2| | 1 |
| Centre Stop lamp obscured more than 50% |1.2.1c| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a pin/bush front |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm pin or bush excessively worn lower arm front bush excessive movement (5.3.4 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded Outer door sill |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded Outer door sill |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded Inner door sill |2.4.A.3| | 1 |
| Offside Front Brake pipe at imminent risk of failure or fracture leading to flexible hose (1.1.11 (a)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced at inner sill/floor (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor/inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor / inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover missing |5.3.4 |b| |ii|| | 1 |
| Emissions NOx sensor obviously defective |8.2.1.1 |a|| | 1 |
| Offside Front Road wheel distorted Fouling caliper |4.2.A.1a| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced at inner wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced at inner wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner/floor sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component corroded and seriously weakened inner/floor sill (5.3.3 (b) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Close to front subframe mountings (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Close to front subframe mountings (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill close to lower seatbelt mounting (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill close to lower seatbelt mounting (7.1.1 (a) (i)) | 1 |
| Nearside Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan to sill area (7.1.1 (a) (i)) | 1 |
| Service brake excessively binding both rear (1.2.1 (f)) | 1 |
| Emissions not tested CO too high (8.2.1.2 (d)) | 1 |
| Offside Rear Suspension arm locating pin incorrectly positioned |2.4.G.3a| | 1 |
| Nearside Headlamp aim beam image obviously incorrect BULB NOT CORRECTLY SEATED IN HOLDER |1.8.A.1b| | 1 |
| Track rod end loose locking device missing |2.2.B.1d| | 1 |
| Offside Rear Wheel stud|s| missing |4.2.A.1e| | 1 |
| Exhaust emissions likely to be affected by an induction leak (8.2.2.1 (b)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis inside wheel arch marked in yellow (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis inside wheel arch marked in yellow (5.3.6 (a) (i)) | 1 |
| Offside Rear Braking system leaking brake calliper |3.6.A.1| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.152 |8.2.1.2 |c|| | 1 |
| Nearside Front Track rod end ball joint has excessive play Inner Lock Nut Loose (2.1.3 (b) (i)) | 1 |
| Offside Front Track rod end ball joint has excessive play Inner Lock Nut Loose (2.1.3 (b) (i)) | 1 |
| Brake pedal anti-slip provision loose (1.1.2 (c)) | 1 |
| Drivers airbag missing non-factory steering wheel fitted (7.1.5 (a)) | 1 |
| Nearside Front Brake pipe likely to become detached or damaged flexi ble hose not secure pipe may chafe (1.1.11 (d) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached cable tie used as locking devivce (5.3.4 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached split pin missing (5.3.4 (a) (ii)) | 1 |
| Nearside Front Lower Suspension component pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Lower Suspension component pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Front Brake pipe likely to become detached or damaged front & brake hose both (1.1.11 (d) (ii)) | 1 |
| Nearside Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Front Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Offside Rear Upper Suspension arm damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Central Front Lower Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction wipers not parking (3.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced cill area (7.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg area (6.1.1 (c) (i)) | 1 |
| Front Upper Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Central Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor n/s (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassi box section near to front (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength body floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill. (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassi rail |6.1.1 |c| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill area perforated (6.2.2 (d) (i)) | 1 |
| Rear Parking brake lever defective so that it cannot be satisfactorily operated (1.1.6 (d)) | 1 |
| Nearside Front Anti-roll bar insecurely attached d bush bolts missing (5.3.3 (a) (i)) | 1 |
| Offside Front Macpherson strut attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Emissions unable to be completed coolant hose failure (8.2.1.2 (d)) | 1 |
| Nearside Inner Steering linkage ball joint has excessive play steering rack arm (2.1.3 (b) (i)) | 1 |
| Rear Oil leaking excessively from transmission differential (8.4.1 (a) (i)) | 1 |
| Stop lamp(s) adversely affected by the operation of another lamp Inoperative with side lights on (4.3.3 (b)) | 1 |
| Brake lever pivot has excessive wear or free play (1.1.1 (b)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section/chassis (5.3.6 (a) (i)) | 1 |
| Rear Emissions not tested too high may damage equipment (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch holed (7.1.1 (a) (i)) | 1 |
| Nearside Track rod end ball joint worn to the extent there is a serious risk of detachment nut missing (2.1.3 (b) (ii)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill and inner wing (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill and inner wing. (6.1.1 (c) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor excessively corroded. |7.1.1 |a| |i|| | 1 |
| Parking brake lever defective so that it cannot be satisfactorily operated |3.1.3c| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits due to blowing |7.3.D.3| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Within 30cm of seat belt mount (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Within 30cm of seat belt mount (6.2.2 (d) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases At Catalyst Flange (6.1.2 (a)) | 1 |
| Emissions not tested CANT HOLD FAST IDLE (8.2.1.2 (d)) | 1 |
| Fuel tank leaking (6.1.3 (b) (i)) | 1 |
| Offside Front Steering locking device missing track rod (2.1.3 (d)) | 1 |
| Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
| Emissions unable to be completed misfire (8.2.1.2 (d)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced n/s+o/s floor (6.1.1 (c) (i)) | 1 |
| Central Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
| Front Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction screen sticker (3.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing from boot area (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength FLOOR BY SUBFRAME MOUNTING. (5.3.6 (a) (i)) | 1 |
| Offside Rear Body insecure inner and outer sill (6.2.2 (a) (i)) | 1 |
| Nearside Front Fluid suspension unit leaking |2.4.D.2| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt boot split (5.3.4 (b) (ii)) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt boot split (5.3.4 (b) (ii)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt boot split (5.3.4 (b) (ii)) | 1 |
| Brake lever has insufficient reserve travel Handbrake Lever too high (1.1.2 (a)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded chassis within anti roll bar bracket mount |2.4.A.3| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced lower wheel arch |6.1.1 |c| |i|| | 1 |
| Exhaust has a major leak of exhaust gases back box and joint (6.1.2 (a)) | 1 |
| Emissions not tested engine over heating (8.2.1.2 (d)) | 1 |
| Nearside Headlamp missing (4.1.1 (a) (ii)) | 1 |
| Brake master cylinder insecure AND BRAKE SERVO (1.1.10 (c)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced both headlamps (4.1.4 (b)) | 1 |
| Nearside Rear Anti-lock braking system wheel speed sensor excessively damaged (1.6 (c)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill Corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill Corroded (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed Engine running rough (8.2.1.2 (d)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits co- 0.63 (8.2.1.2 (b)) | 1 |
| Offside Rear Anti-roll bar linkage attachment bracket/mounting likely to fail (5.3.3 (b) (ii)) | 1 |
| Windscreen wiper not working both (3.4 (a)) | 1 |
| Offside Rear Hydraulic brake calliper inadequately mounted and braking performance affected (1.1.16 (c) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill in several places (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced front centre and rear undersill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Floor and sill corroded. (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Floor and sill corroded. (7.1.1 (a) (i)) | 1 |
| Nearside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Offside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill. (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill. (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed Fan belt shredded during test (8.2.1.2 (d)) | 1 |
| Brake performance unable to be tested Fan belt shredded during test (1.2.1 (g)) | 1 |
| Offside Rear Anti-roll bar damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D-Bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn D-Bush (5.3.4 (a) (i)) | 1 |
| Rear Service brake excessively binding both nearside and offside (1.2.1 (f)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill (6.1.1 (c) (i)) | 1 |
| Rear fog lamp adversely affected by the operation of another lamp (4.5.4 (b)) | 1 |
| Nearside Front Body panel damaged and likely to cause injury wing (6.2.1 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt upper and lower (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt upper and lower (5.3.4 (b) (ii)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits in my opinion the car was manufactured before 2002, poss as early as 1991. owner needs to provide proof of date of manufacture. (8.2.1.2 (b)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch/chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front position lamp|s| flickers when tapped lightly by hand |1.1.4c| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded Wing |2.4.A.3| | 1 |
| Front Anti-roll bar linkage pin or bush excessively worn Nearside / Offside |5.3.4 |a| |i|| | 1 |
| Driver`s airbag missing warning lamp on |5.4.1| | 1 |
| Main beam `tell-tale` not working on constantly when headlights switched on |1.7.4c| | 1 |
| Electrical wiring insecure O/S door shut and engine bay |1.9.2a| | 1 |
| Electrical wiring inadequately supported O/S door shut and engine bay |1.9.2a| | 1 |
| Nearside Rear Brake pipe leaking on an air braking system (1.1.11 (b) (i)) | 1 |
| Power steering pump leaking from a failed seal |2.3.3b| | 1 |
| Offside Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill area holed by corrosion (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings BOOT FLOOR |6.1.B.2| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER SILL BEHIND WHEEL |6.1.B.2| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER SILL |6.1.B.2| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint ANTI-ROLL BAR DROP LINK |2.4.G.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill covered in filler, corroded underneath (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill covered in filler, corroded underneath (5.3.6 (a) (i)) | 1 |
| Front Headlamp light source and lamp not compatible both headlight converted to HID (4.1.4 (c)) | 1 |
| Nearside Front position lamp|s| has a product on the light source so it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front position lamp|s| has a product on the light source so it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut top |5.3.6 |a| |i|| | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt dust cover (5.3.4 (b) (ii)) | 1 |
| Offside Rear Torsion bar deteriorated by corrosion so that its cross sectional area is reduced and seriously weakened |2.4.E.1b| | 1 |
| Offside Front Suspension arm insecure |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired patch not welded correctly (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired sill not welded at rear (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired not welded at rear (5.3.6 (a) (i)) | 1 |
| Nearside Rear Sub-frame rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Sub-frame rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WHEEL ARCH (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WHEEL ARCH (5.3.6 (a) (i)) | 1 |
| Braking system leaking o/s/r brake caliper |3.6.A.1| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded inner undersill |2.4.A.3| | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill rear (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front chassis corroded near suspension mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded sill to floor pan |5.2.6| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded sill to floor pan |5.2.6| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded sill to floor pan |5.2.6| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded sill to floor pan |5.2.6| | 1 |
| Front Inner Suspension component mounting prescribed area is excessively corroded floor pan |2.4.A.3| | 1 |
| Rear Lower Suspension component mounting prescribed area is excessively corroded inner sill/arch /floor |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner and a outer sill |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner and outer sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner and outer sill |2.4.A.3| | 1 |
| Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Axle mounting retaining cups have corroded away (5.3.6 (a) (ii)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill has a hole through (6.1.1 (c) (i)) | 1 |
| Seat belt buckle not functioning as intended osf not releasing when under tension (7.1.2 (d)) | 1 |
| Rear Hydraulic brake calliper leaking Nearside and Offside (1.1.16 (b) (i)) | 1 |
| Nearside Rear Inner Brake prescribed area is excessively corroded sill [2.5 (1.1.21 (e) (i)) | 1 |
| Offside Rear Floor excessively deteriorated corrosion in boot under battery [3] (6.2.4 (a) (i)) | 1 |
| Power steering pipe/hose excessively corroded into steering rack |2.1.5 |g| |i|| | 1 |
| Power steering pipe/hose excessively corroded out of steering rack |2.1.5 |g| |i|| | 1 |
| Nearside Front Anti-roll bar linkage corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Front Anti-roll bar linkage corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Power steering pipe|s| or hose|s| leaking corroded pipe |2.3.3b| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor/inner sill area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced chassis outrigger at rear (7.1.1 (a) (i)) | 1 |
| Headlamp aim projected beam image is obviously incorrect both front (4.1.2 (c)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Nearside front chassis/floor/inner sill |5.3.6 |a| |i|| | 1 |
| Brake prescribed area is excessively corroded Offside chassis |1.1.21 |e| |i|| | 1 |
| rear brake recording little or no effort both |3.7.B.5a| | 1 |
| Exhaust has a major leak of exhaust gases Front and rear |7.1.2| | 1 |
| Suspension component mounting prescribed area is excessively corroded nearside front floor |2.4.A.3| | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/wing (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Lower Suspension arm fractured |2.4.G.1| | 1 |
| Power steering pipe/hose leaking N/S/F of engine bay (2.1.5 (a)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear (6.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded cassis |2.4.A.3| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner arch (6.2.2 (d) (i)) | 1 |
| Offside Front Lower Suspension component ball joint likely to become detached Securing nut missing and bolt is loose (5.3.4 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Emissions unable to be completed Big hole in exhaust (8.2.1.2 (d)) | 1 |
| Rear fog lamp does not emit a steady red light Light Is White (4.5.4 (a)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak Tail Box (8.2.1.1 (b)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Seatbase anchorage point (7.1.1 (a) (i)) | 1 |
| Offside Rear Brake hose excessively damaged RUBBING ON WHEEL (1.1.12 (b) (ii)) | 1 |
| Offside Rear Brake performance not tested FLEXI DAMAGED (1.2.1 (g)) | 1 |
| Emissions not tested COOLANT LEAK (8.2.1.2 (d)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill severally corroded (6.2.2 (d) (i)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits cat missing (8.2.1.2 (b)) | 1 |
| Emissions unable to be completed Due to engine overheating (8.2.1.2 (d)) | 1 |
| Rear Service brake effort inadequate at a wheel both (1.2.1 (a) (i)) | 1 |
| Rear Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Front Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
| Offside Front Body panel damaged and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Suspension arm pin or bush excessively worn both front (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension arm insecure and impairing directional stability |5.3.3 |a| |ii|| | 1 |
| Nearside Headlamp aim beam image obviously incorrect and offside |1.8.A.1b| | 1 |
| Offside Front Obligatory mirror missing (3.3 (a)) | 1 |
| Offside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill holed (6.1.1 (c) (i)) | 1 |
| Front Steering locking device ineffective Both steering pins missing (2.1.3 (d)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill- within 30cm of suspension arm mounting. (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Body panel damaged and likely to cause injury wing (6.2.1 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area fractured significantly reducing structural strength step area (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak Centre box (8.2.1.1 (b)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill (7.1.1 (a) (i)) | 1 |
| Rear Brake lever has insufficient reserve travel no reserve travel in handbrake (1.1.2 (a)) | 1 |
| Rear Service brake effort inadequate at a wheel both n/s o/s rear service brake [foot brake] showing low effort at rear wheels (1.2.1 (a) (i)) | 1 |
| Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel rear handbrake showing low effort at rear wheels (1.3.1 (a) (i)) | 1 |
| Front Headlamp not working on main beam front both n/s o/s headlights not working on main and dip (4.1.1 (a) (ii)) | 1 |
| Emissions unable to be completed due to [bad] exhaust leaking gases (8.2.1.2 (d)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak exhaust leaking gases [possible front flix pipe] (8.2.2.1 (b)) | 1 |
| Emissions not tested excessive smoke (8.2.1.2 (d)) | 1 |
| Headlamp aim not tested headlamp operating device not working (4.1.2 (b)) | 1 |
| Front Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Offside Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury Wheel arch (6.2.1 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt lower arm (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt upper arm (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt lower arm (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Position lamp lens seriously defective always on (4.2.1 (b)) | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint upper |2.4.G.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering around front anti-roll bar fixing and front suspension |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering around front anti-roll bar fixing and front suspension |6.1.A.1| | 1 |
| Offside Front Road wheel cracked |4.2.A.1a| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis to sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt upper (5.3.4 (b) (ii)) | 1 |
| Nearside Front brake caliper locking device insecure brake caliper carrier bolt loose excessive play |3.5.1l| | 1 |
| Nearside Front Lower Suspension component ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail holed (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced under sill at rear (6.1.1 (c) (i)) | 1 |
| Offside Track rod end ball joint dust cover missing (2.1.3 (g) (ii)) | 1 |
| Offside Front Lower Suspension component ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Emissions unable to be completed major exhaust blow (8.2.1.2 (d)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced under side sill at rear (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Suspension arm locating pin retaining device not properly locked |2.4.G.3b| | 1 |
| Nearside Front Power steering pipe/hose leaking In engine bay. (2.1.5 (a)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/ floor (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/ floor (6.1.1 (c) (i)) | 1 |
| Emissions unable to be completed due to major exhaust leak (8.2.1.2 (d)) | 1 |
| Nearside Front Brake hose excessively twisted and chaffing |1.1.12 |b| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion on sil |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill / nerd arch. (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill. |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill. |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front section of chassis excessively corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Hydraulic brake calliper leaking and braking performance affected leaking from piston area (1.1.16 (b) (ii)) | 1 |
| Nearside Front Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
| Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Corroded through by sub frame mounting. |6.1.1 |c| |i|| | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn Upper joint is detached. |5.3.4 |a| |i|| | 1 |
| Offside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis close to suspension component mount excessive corrosion. |6.1.B.2| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill / floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced valance / floor (6.1.1 (c) (i)) | 1 |
| Rear Anti-roll bar corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Rear Parking brake inoperative on one side BOTH SIDES INOPERATIVE (1.4.1 (a)) | 1 |
| Nearside Front Inner Integral body structure has excessive corrosion which adversely affects braking or steering on chassis near anti roll bar bracket (6.1.1 (c) (ii)) | 1 |
| brake disc in such a condition that it is seriously weakened both rear |3.5.1i| | 1 |
| Nearside Front Anti-roll bar has excessive play in a ball joint snapped |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis leg |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis leg |5.3.6 |a| |ii|| | 1 |
| Central Rear Braking system leaking brake pipe |3.6.A.1| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis Leg - Roll Bar Mount (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis Leg - Roll Bar Mount (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced boot flour corroded batterie loose (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer rigger (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded Inner wheel arch |2.4.A.3| | 1 |
| Offside Front Upper Seat belt anchorage prescribed area is excessively corroded Inner wheel arch |5.2.6| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Inner wing / chassis |6.1.A.1| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner arch chassis |5.3.6 |a| |ii|| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Floor pan |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Floor pan |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill excessively corroded (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mount CHASSIS |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mount CHASSIS |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill & floor to sill |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill & floor to sill in various areas |5.2.6| | 1 |
| Battery insecure battery tray has corrosion |1.9.1| | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Centre Stop lamp excessively deteriorated so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Rear Coil spring fractured or broken both |5.3.1 |b| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill rotten |7.1.1 |a| |i|| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Chassis leg in wheel arch |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill/ floor |6.1.B.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/ chassis |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/ chassis |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/ floor (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/ floor (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor section (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor section (5.3.6 (a) (i)) | 1 |
| Offside Front Lower coil spring broken |2.4.C.1a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded front chassis all around roll bar mounting |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded all around chassis / roll bar mounting area |2.4.A.3| | 1 |
| Offside Rear Braking system leaking brake caliper body wet with brake fluid |3.6.A.1| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded inner sill/floor/outer sill area |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill/inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis near roll bar mount |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor 2 parts |5.2.6| | 1 |
| Front brake caliper leaking |3.6.A.1| | 1 |
| Offside Rear Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Brake performance not tested no handbrake (1.2.1 (g)) | 1 |
| Power steering component|s| leaking steering rack |2.3.3b| | 1 |
| Nearside Front Front suspension has a suspension lower ball joint securing nut loose corroded away |2.5.B.1a| | 1 |
| Offside Front Front suspension has a suspension lower ball joint securing nut loose corroded away |2.5.B.1a| | 1 |
| Offside Front Anti-roll bar linkage insecurely attached drop link |5.3.3 |a| |i|| | 1 |
| Anti-lock braking system warning lamp is missing. |3.4.1a| | 1 |
| Rear Exhaust has a major leak of exhaust gases blowing at rear flange badley rusted (6.1.2 (a)) | 1 |
| Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting both side (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner seal (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner seal (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner seal (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner seal (6.1.1 (c) (i)) | 1 |
| Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Outer Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front brake disc modified and seriously weakened |3.5.1n| | 1 |
| Offside Front brake disc modified and seriously weakened |3.5.1n| | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill /arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Large section of chassis rail antilroll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Large section of chassis rail anitroll bar mounting (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear exhaust joint (6.1.2 (a)) | 1 |
| Front coil spring broken N/S+O/S FRONT |2.4.C.1a| | 1 |
| Nearside Front All direction indicators adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor below battery (6.2.2 (d) (i)) | 1 |
| Steering wheel has movement relative to the column such that there is a serious risk of detachment (2.2.1 (a) (ii)) | 1 |
| Nearside Rear Lower Suspension arm insecure and impairing directional stability inner (5.3.3 (a) (ii)) | 1 |
| Offside Rear Upper Suspension arm insecure and impairing directional stability outer (5.3.3 (a) (ii)) | 1 |
| Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Direction indicator not working |1.4.A.2c| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint likely to become detached drop link |5.3.4 |a| |ii|| | 1 |
| Offside Front Suspension arm fractured |2.4.G.1| | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened shock mount |2.4.G.1| | 1 |
| Nearside Rear Lower Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills both sides (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Suspension arm damaged and seriously weakened corroded as marked |2.4.G.1| | 1 |
| Offside Rear Lower Suspension arm damaged and seriously weakened corroded as marked |2.4.G.1| | 1 |
| Offside Rear Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Offside Rear Hydraulic brake calliper inadequately mounted |1.1.16 |c| |i|| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint has snapped |2.4.G.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill holed |6.1.B.2| | 1 |
| Front Coil spring fractured or broken both (5.3.1 (b) (i)) | 1 |
| Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength underfloor (5.3.6 (a) (i)) | 1 |
| Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner under sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under sill |7.1.1 |a| |i|| | 1 |
| Offside Front Lower Body insecure wing |6.2.2 |a| |i|| | 1 |
| Offside Rear Body component corroded and likely to cause injury arch |6.2.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill / sill to floor area |5.2.6| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak leaking from monts (8.2.2.1 (b)) | 1 |
| Nearside Front Lower Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Front Lower Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Rear Lower Body panel damaged and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Rear Lower Battery insecure and likely to fall from carrier hole below battery (4.13 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn droplink (5.3.4 (a) (i)) | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Front Obligatory mirror missing |8.1.1| | 1 |
| Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt n/s/r |2.4.G.2| | 1 |
| Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt o/s/r |2.4.G.2| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases center section (6.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis Rail Forward of Suspension |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis rail by front antiroll bar mounting (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis rail corroded by front antiroll bar mounting (5.3.6 (a) (ii)) | 1 |
| Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected offside front floor pan holed (5.3.6 (a) (ii)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 1 |
| Offside Rear Battery insecure and likely to fall from carrier corroded (4.13 (a) (ii)) | 1 |
| Offside Front Vehicle structure has a modification which adversely affects braking or steering inner wheel housing |6.1.A.1| | 1 |
| Offside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Nearside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Offside Rear Braking system leaking flexi hose to caliper joint |3.6.A.1| | 1 |
| Nearside Rear Outer Subframe mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner sill area. (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength Sill area. (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Floor area. (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis member. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Tie bar/rod attachment bracket inappropriately repaired |2.4.A.2| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sub-frame (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded on sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded on sill |5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases Center pipe and rear box |6.1.2 |a|| | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Nearside Rear Integral body structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Offside Rear Integral body structure has a fractured which is likely to adversely affect braking or steering (6.1.1 (a) (ii)) | 1 |
| Offside Outer Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Offside Seat belt anchorage likely to become detached in the event of a collision (7.1.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases REAR |7.1.2| | 1 |
| Offside Inner Rear brake disc excessively scored |3.5.1h| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s sill |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings o/s rear inner sill |6.1.B.2| | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 1 |
| Valve stem seriously damaged all |5.2.3 |j|| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner wing/chassis leg |2.4.A.3| | 1 |
| Nearside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure and impairing directional stability |5.3.3 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outersill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt upper and lower |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt upper and lower |2.4.G.2| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sil (7.1.1 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength BOTH FRONT CHASSIS MEMBERS (5.3.6 (a) (i)) | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Rear front brake binding both |3.7.B.1| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner floor |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 1 |
| Offside Front Suspension arm locating pin retaining device missing |2.4.G.3b| | 1 |
| Offside Front Front position lamp|s| not working sidelight |1.1.A.3b| | 1 |
| Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 1 |
| Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner and outer sill , next to jacking point (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis above top suspension arm mounting |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis above top suspension arm mounting |5.3.6 |a| |ii|| | 1 |
| Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Rear Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength BOTH SIDE |5.2.6| | 1 |
| Nearside Front Front position lamp|s| obscured more than 50% |1.1.A.3c| | 1 |
| Nearside Front Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Side repeater incorrect colour |1.4.A.2f| | 1 |
| Offside Front Side repeater incorrect colour |1.4.A.2f| | 1 |
| Nearside Rear Upper Suspension arm fractured |2.4.G.1| | 1 |
| Nearside Front Lower Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Front Anti-roll bar mounting modified so the suspension is likely to fail other components (5.3.3 (c) (ii)) | 1 |
| Offside Front Anti-roll bar linkage which is adjustable, locking device insecure |2.4.G.1| | 1 |
| Nearside Rear Anti-roll bar linkage which is adjustable, locking device insecure |2.4.G.1| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Chassis rail |5.2.6| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering in wheel arch by suspension pick up points for suspension arm and anti roll bar (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering off side front under car osf main chassis rail (6.1.1 (c) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded near anti roll bar |2.4.A.3| | 1 |
| Nearside Front Power steering pipe/hose leaking Behind radiator (2.1.5 (a)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Nearside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill (6.2.2 (d) (i)) | 1 |
| Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases Flange (6.1.2 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill - Holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Battery insecure in the boot
|1.9.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill backing (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outter sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outter sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg near sub frame mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg inadequate repair (5.3.6 (a) (i)) | 1 |
| Nearside Front Power steering ram leaking (2.1.5 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg behind the front sub frame (6.2.2 (d) (i)) | 1 |
| Offside Rear Brake hose excessively twisted (1.1.12 (b) (ii)) | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outter sill (7.1.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases tailbox and centre box (6.1.2 (a)) | 1 |
| Nearside Rear Lower Suspension arm likely to become detached (5.3.3 (a) (ii)) | 1 |
| Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill corroded |6.2.2 |d| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill corroded |6.2.2 |d| |i|| | 1 |
| Exhaust has a major leak of exhaust gases Back box |7.1.2| | 1 |
| Offside Rear Headlamp not working on dipped beam |1.7.5a| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak center to rear exhaust leak joint rusty (8.2.1.1 (b)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded to upper inner sill & holed |5.2.6| | 1 |
| Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion which adversely affects braking or steering wheel arch (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion which adversely affects braking or steering sill (6.1.1 (c) (ii)) | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` mirror hanger, tax disc holder |8.3.1e| | 1 |
| Brake performance not tested Offside rear caliper leaking. (1.2.1 (g)) | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper leaking |1.1.16 |b| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger corroded (5.3.6 (a) (i)) | 1 |
| Offside Front Brake hose leaking on a hydraulic braking system Brake hose to calliper (1.1.12 (c) (ii)) | 1 |
| Offside Front Inner Road wheel badly distorted (5.2.2 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor to sill corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Road wheel badly distorted (5.2.2 (c) (i)) | 1 |
| Offside Front Lower Steering locking device ineffective Ball joint split pin (2.1.3 (d)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting in wheel arch tub. (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting in wheel arch tub. (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill. (7.1.1 (a) (i)) | 1 |
| Emissions not tested hole in exhuant back box (8.2.1.2 (d)) | 1 |
| Rear Exhaust has a major leak of exhaust gases center and back box exhuant (6.1.2 (a)) | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer box , and centre box joint . |6.1.2 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mount. (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mount. (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill. (6.1.1 (c) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded rear sill |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded rear sill |5.2.6| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
| Braking system leaking front to rear brake pipe corroded and leaking |3.6.A.1| | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired rear sill |5.2.6| | 1 |
| Offside Front All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis holed at antiroll bar mounting point (5.3.6 (a) (i)) | 1 |
| Front Exhaust catalytic converter missing where one was fitted as standard (8.2.2.1 (a)) | 1 |
| Central Exhaust has a major leak of exhaust gases box (6.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis rail (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassi (5.3.6 (a) (i)) | 1 |
| Front Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Rear Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Rear Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area |6.1.B.2| | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area |6.1.B.2| | 1 |
| Rear Brake disc significantly and obviously worn INNER FACES. (1.1.14 (a) (i)) | 1 |
| Front Horn not working |7.7 |a| |ii|| | 1 |
| Front Service brake excessively fluctuating both |1.2.1 |e|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rear outer sill |7.1.1 |a| |i|| | 1 |
| Fuel cap/sealing device sealing washer torn |7.2.4c| | 1 |
| Power steering pipe|s| or hose|s| leaking from rack to cooler returning to tank |2.3.3b| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded above suspension arm mounting |2.4.A.3| | 1 |
| Nearside Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen |3.5 |a|| | 1 |
| Exhaust has a major leak of exhaust gases Middle and back box corroded and holed. |6.1.2 |a|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to sill. |7.1.1 |a| |i|| | 1 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Emissions unable to be completed EXHAUST BLOW (8.2.2.2 (e)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill up right (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt stitching badly frayed |5.2.2b| | 1 |
| Front Upper Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail in engine bay both sides x2 (6.2.2 (d) (i)) | 1 |
| Rear Upper Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rear shocker upper mount area both sides x2 (6.2.2 (d) (i)) | 1 |
| Offside Front Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting from sil toward the the wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Front Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting from sil toward the the wheel arch (6.2.2 (d) (i)) | 1 |
| Front Position lamp not working both front (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength Chassis rail |5.3.6 |a| |i|| | 1 |
| Offside Front Brake hose connection leaking on a hydraulic braking system |1.1.12 |c| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis by shock top under bonnet holed (5.3.6 (a) (ii)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill under vehicle (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wing under arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill area (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor several areas (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint likely to become detached has come detatched (5.3.4 (a) (ii)) | 1 |
| Rear Brake disc significantly and obviously worn Both (1.1.14 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front and rear sill (5.3.6 (a) (i)) | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front and rear sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar corroded and seriously weakened Inner wing. |2.4.G.1| | 1 |
| Offside Rear rear brakes release unevenly |3.7.B.4| | 1 |
| Offside Rear Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Central Front Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill as marked |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded as marked |5.2.6| | 1 |
| Front rear brake excessively fluctuating |3.7.B.3| | 1 |
| front parking |secondary| brakes imbalanced 40% |3.7.B.6b| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis in wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill holed |5.2.6| | 1 |
| Offside Front Front position lamp|s| has a product on the lens so it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassi and sills several places (6.1.1 (c) (i)) | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Exhaust has a major leak of exhaust gases exhaust centre section (7.1.2) | 1 |
| Emissions not tested due to leaking exhaust (7.3.A.1) | 1 |
| Nearside Braking system leaking |3.6.A.1| | 1 |
| Rear Lower Suspension arm corroded and seriously weakened n/s and o/s |2.4.G.1| | 1 |
| Offside Side repeater not working (1.4.A.2c) | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Position lamp not working Both nearside and offside front (4.2.1 (a) (ii)) | 1 |
| Nearside Headlamps matched pair are not the same colour |1.7.6| | 1 |
| Offside Front Anti-roll bar insecure to the link |2.4.G.1| | 1 |
| Nearside Front Suspension arm modified so the suspension is likely to foul other components rubbing on front shock absorber (5.3.3 (c) (ii)) | 1 |
| Offside Rear Anti-roll bar ball joint likely to become detached nut loose (5.3.4 (a) (ii)) | 1 |
| Offside Rear Upper Anti-roll bar attachment bracket/mounting damaged and seriously weakened cut through with angle grinder (5.3.3 (b) (i)) | 1 |
| Offside Front Lower Anti-roll bar attachment bracket/mounting damaged and seriously weakened cut through with angle grinder (5.3.3 (b) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Front Hydraulic fluid leaking excessively power steering pipe |8.4.1 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Suspension arm insecurely attached split pin missing (5.3.3 (a) (i)) | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill marked up |6.1.B.2| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting hole in sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt RODENT DAMAGE |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt RODENT DAMAGE |2.4.G.2| | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced Bulb not in correct |1.7.5a| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Body has a sharp edge caused by corrosion wing |6.1.C.1| | 1 |
| Offside Front Lower Body has a sharp edge caused by corrosion wing |6.1.C.1| | 1 |
| Nearside Front Road wheel fractured (5.2.2 (a)) | 1 |
| Nearside Rear Road wheel fractured (5.2.2 (a)) | 1 |
| Offside Stop lamp(s) emits other than a steady red light showing white light (4.3.3 (a) (ii)) | 1 |
| Offside Front Vehicle structure is fractured and structural rigidity is significantly reduced chassis leg (6.1.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced chassis |2.4.G.1| | 1 |
| Rear Stop lamp(s) light intensity significantly reduced (4.3.3 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected anti roll bar (5.3.6 (a) (ii)) | 1 |
| Rear Anti-roll bar ball joint likely to become detached ns os movement x2 (5.3.4 (a) (ii)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis x2 ns os (5.3.6 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arches inner ns os (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top mountain (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis under drivers seat (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor Pan (7.1.1 (a) (i)) | 1 |
| Front Service brake excessively binding x2 (1.2.1 (f)) | 1 |
| Brake pipe leaking Nearside rear section of front to rear, above rear axle. |3.6.A.1| | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn Excessive play (5.3.4 (a) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Nearside rear outer sill (6.2.2 (d) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Offside rear outer sill (6.2.2 (d) (i)) | 1 |
| Front Anti-roll bar linkage has excessive play in a ball joint X 2 |2.4.G.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill/floor |7.1.1 |a| |i|| | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint likely to become detached lower broken |5.3.4 |a| |ii|| | 1 |
| Emissions not tested MIS FIRE (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail corroded |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases Centre To Rear Silencer Joint (6.1.2 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area is excessively corroded nearside front chassis rail |2.4.A.3| | 1 |
| Central Exhaust has a major leak of exhaust gases centre exhaust broken at flange (6.1.2 (a)) | 1 |
| Emissions unable to be completed Vehicle overheats (8.2.1.2 (d)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced Offside rear outer sill |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced x2 (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced x2 (7.1.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill/ wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure is deformed and structural rigidity is significantly reduced chassis leg (6.1.1 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis holed at front subframe mounting area (5.3.6 (a) (i)) | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Nearside front inner wheel arch |6.1.B.2| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Offside front inner wheel arch |6.1.B.2| | 1 |
| Offside Front Lower Suspension arm damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Steering arm deformed to the extent that steering is affected (2.1.3 (c) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced lower outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/chassis rail holed and corroded (5.3.6 (a) (i)) | 1 |
| Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Front Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength quarter cill |5.3.6 |a| |i|| | 1 |
| Brake lever has restricted free movement no reserve travel park brake lever (1.1.15 (e)) | 1 |
| Offside Front Braking system leaking brake caliper |3.6.A.1| | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction interior mirror (3.1 (a) (ii)) | 1 |
| Nearside Front Brake hose connection leaking on a hydraulic braking system banjo leaking (1.1.12 (c) (ii)) | 1 |
| Rear Rear fog lamp lens defective such that emitted light is adversely affected lens broken (4.5.1 (b) (ii)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Central Front Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Central Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded floor pan |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis area chalked (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis area chalked (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Nearside Front Service brake excessively binding can not turn wheel (1.2.1 (f)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt bottom lower arm dust cover split (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt bottom lower arm dust cover split (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill / A pillar (5.3.6 (a) (i)) | 1 |
| Offside Rear Road wheel fixing loose (5.2.1 (a) (i)) | 1 |
| Nearside Rear Inner Vehicle structure strengthening plate or fastening insecure Cill Section (6.1.1 (b) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
| Brake disc significantly and obviously worn rears (1.1.14 (a) (i)) | 1 |
| Offside Front Lower Anti-roll bar attachment bracket/mounting fractured front attachment to lower suspension arm (5.3.3 (b) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength engine mounting area (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength engine mounting area (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced o/s outter sill holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side very low effort recorded (1.4.1 (a)) | 1 |
| Offside Front Braking system leaking caliper |3.6.A.1| | 1 |
| Nearside Front Braking system leaking caliper |3.6.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Marked in yellow |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Marked in yellow |5.2.6| | 1 |
| Offside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Power steering pump drive system defective |2.3.6| | 1 |
| Front Power steering pipe|s| or hose|s| excessively corroded All |2.3.2| | 1 |
| Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings weld incorrect |6.1.B.2| | 1 |
| Nearside Front Anti-roll bar attachment bracket inappropriately repaired |2.4.A.2| | 1 |
| Offside Front Anti-roll bar attachment bracket inappropriately repaired |2.4.A.2| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail (6.1.1 (c) (i)) | 1 |
| Nearside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings n/s rear sill |6.1.B.2| | 1 |
| Offside Front Body panel insecure outer sill (6.2.1 (a) (i)) | 1 |
| Offside Rear Body component damaged and likely to cause injury aerial |6.2.1 |a| |i|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced seal corroded (7.1.1 (a) (i)) | 1 |
| Offside Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Upper Macpherson strut ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting likely to become detached bolt loose (5.3.3 (a) (ii)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer (6.1.1 (c) (i)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect light dim (4.1.2 (c)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill inner and outer (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases catalyst (6.1.2 (a)) | 1 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced bulb (4.1.4 (b)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wing (7.1.1 (a) (i)) | 1 |
| Emissions not tested engine starting to over heat emissions too high (8.2.1.2 (d)) | 1 |
| Nearside Front Obligatory mirror missing |8.1.1| | 1 |
| Offside Rear Electrical wiring inadequately supported |1.9.2a| | 1 |
| Nearside Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Offside Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch rotten (6.1.1 (c) (i)) | 1 |
| Central Front Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Upper Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Upper Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Upper Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch on chassis (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch on chassis (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting seal by back wheel (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting seal by rear wheel (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (LARGE) (5.3.6 (a) (i)) | 1 |
| Central Front Drivers view of the road through the swept area of the windscreen materially affected by an obstruction (3.1 (a) (ii)) | 1 |
| Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced and Inner sill (7.1.1 (a) (i)) | 1 |
| Emissions not tested Idle speed randomly increased to over 2000rpm during emission test. Emission test aborted (8.2.1.2 (d)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded INNER WHEEL ARCH |2.4.A.3| | 1 |
| Nearside Rear Braking system leaking BRAKE PIPE TO CALIPER |3.6.A.1| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded SILL |5.2.6| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt BOOT SPLIT |2.4.G.2| | 1 |
| Offside Subframe mounting prescribed area is excessively corroded sill and floor |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded box section |2.4.A.3| | 1 |
| Nearside Rear Inner Subframe mounting prescribed area is excessively corroded sill and box section |2.4.A.3| | 1 |
| Front Valve stem seriously damaged |4.1.D.1e| | 1 |
| Rear Valve stem seriously damaged |4.1.D.1e| | 1 |
| Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis near anti roll bar fixing |2.4.A.3| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill
|evidence of previous covering of corrosion with body filler|. |7.1.1 |a| |i|| | 1 |
| Suspension arm pin or bush excessively worn BOTH FRONT WISHBONE FOREMOST BUSHES WORN |5.3.4 |a| |i|| | 1 |
| Offside Front Lower Suspension arm insecurely attached ARM FRONT BOLT SLACK |5.3.3 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage insecurely attached BOTTOM NUT ON THE DROPLINK SLACK |5.3.3 |a| |i|| | 1 |
| Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Nearside Rear Upper Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mounting area on offside chassis rail |2.4.A.3| | 1 |
| Nearside Front Lower Body panel likely to become detached Wing mounting point (6.2.1 (a) (ii)) | 1 |
| Offside Front Lower Body panel likely to become detached Wing mounting point (6.2.1 (a) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill panel (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill panel (5.3.6 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded |6.1.1 |c| |i|| | 1 |
| Nearside Headlamp insecure bulb |1.7.3| | 1 |
| Nearside Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Nearside Front Shock absorbers has an excessively worn bush |5.3.2 |c|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill two holes |7.1.1 |a| |i|| | 1 |
| Front Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Rear inside sill |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Rear inside sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg corroded (5.3.6 (a) (i)) | 1 |
| Nearside Rear Braking system leaking caliper leaking |3.6.A.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases leak at rear joint |7.1.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Sill end |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired lower sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Anti- Roll bar mounting area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension arm attachment bracket/mounting nut missing |2.4.G.1| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer door sill |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded along front chassis rail |2.4.A.3| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill corroded |6.1.B.2| | 1 |
| Front Windscreen wiper not working both |3.4 |a|| | 1 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle |6.2.3 |a|| | 1 |
| Nearside Front Front passenger door cannot be opened from outside the vehicle |6.2.3 |a|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg underside |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure is fractured and structural rigidity is significantly reduced outer sill and filler (6.1.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced outer sill (6.1.1 (d) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Rear Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill corroded and holed (6.1.1 (c) (i)) | 1 |
| Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength at o/s/f and n/s/f chassis areas sides and bottom edges (5.3.6 (a) (i)) | 1 |
| Anti-roll bar attachment bracket/mounting corroded and seriously weakened o/s/f and n/s/f chassis (5.3.3 (b) (i)) | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid Calliper |1.1.16 |b| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded doorsill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded doorsill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassi |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassi |2.4.A.3| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear outer sill corroded resulting in holes |6.1.1 |c| |i|| | 1 |
| Central Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Centre front brake binding |3.7.B.1| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Floor and inner sill |5.2.6| | 1 |
| Offside Inner Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Position lamp not working SIDE LIGHT (4.2.1 (a) (ii)) | 1 |
| Offside Front Position lamp not working SIDE LIGHT (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill has corrosion hole |5.2.6| | 1 |
| Rear fog lamp does not emit a steady red light showing white light to rear. (4.5.4 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced in front of wheel - sill + closing panel inner wheel arch - marked with blue chalk (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced in front of wheel - sill - marked with blue chalk (7.1.1 (a) (i)) | 1 |
| Offside Rear Floor excessively deteriorated boot floor - marked with blue chalk (6.2.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis marked with blue chalk |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis marked with blue chalk |5.3.6 |a| |i|| | 1 |
| Offside Rear Brake hose twisted |3.6.B.4c| | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired centre floor as marked (7.1.1 (a) (i)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury rear wheel arch to outer sill (6.2.1 (a) (i)) | 1 |
| Drivers airbag missing Racing Steering Wheel fitted (7.1.5 (a)) | 1 |
| Drivers airbag missing sport steering wheel fitted (7.1.5 (a)) | 1 |
| Exhaust system not adequately supported Back box bracket broken |7.1.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded Cill |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Cill |5.2.6| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/ inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL. |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL. |5.3.6 |a| |i|| | 1 |
| Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength both chassis between subframe and anti roll bar mounts (5.3.6 (a) (i)) | 1 |
| Nearside Front Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Rear sill has corrosion within 30cm of rear most seat belt mount and seat mount |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Rear sill has corrosion within 30cm of rear most seat belt mount and seat mount |7.1.1 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases mid and rear |7.1.2| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded and component area |2.4.A.3| | 1 |
| Exhaust emits visible black smoke at idle (8.2.1.2 (f)) | 1 |
| Emissions not tested not tested due to excessive smoke (8.2.1.2 (d)) | 1 |
| Nearside Front Lower Suspension arm corroded and seriously weakened hold under shocker mounting point (5.3.3 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassi rail antiroll bar mount point area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassi rail area of antiroll bar mount point area (5.3.6 (a) (i)) | 1 |
| Nearside Front Side repeater missing |1.4.A.2b| | 1 |
| Rear Brake disc significantly and obviously worn both rear (1.1.14 (a) (i)) | 1 |
| Nearside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Headlamp levelling device inoperative both (4.1.5 (a)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing /chassis leg under bonnet (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg - underneath rotted away (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg - underneath (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength End sill (5.3.6 (a) (i)) | 1 |
| Front Brake disc significantly and obviously worn both (1.1.14 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner wing (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Hole in inner wing near suspension component (6.1.1 (c) (i)) | 1 |
| Oil leaking excessively from engine AROUND CRANK PULLEY AREA (8.4.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases BACKBOX JOIN (6.1.2 (a)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL CORRODED/FULL OF EXHAUST PASTE (6.1.1 (c) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded outter sill |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded outter sill |2.4.A.3| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill |6.2.2 |d| |i|| | 1 |
| Rear Exhaust system insecure broken from centre join |6.1.2 |a|| | 1 |
| Rear Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Passenger`s seat insecure |6.2.A.1| | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arche (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arche (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak high lambda reading (8.2.1.1 (b)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Headlamp light intensity severely reduced both (4.1.4 (a)) | 1 |
| Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting both sils and nearside inner at rear (6.2.2 (d) (i)) | 1 |
| Emissions not tested Catalytic converter missing (8.2.2.2 (e)) | 1 |
| Emissions not tested no cat and noise from engine requires inspection (8.2.1.2 (d)) | 1 |
| Headlamp not working on dipped beam both bulbs missing |4.1.1 |a| |ii|| | 1 |
| brake disc contaminated by brake fluid |3.5.1h| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outter sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outter sill (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed engine missfire !! (8.2.1.2 (d)) | 1 |
| Nearside Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
| Offside Front Seat belt installation causes a lap belt to be incorrectly positioned across the occupant (10.1 (u)) | 1 |
| Nearside Front Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill / arch |5.3.6 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Macpherson strut corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Rear Anti-roll bar linkage corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Front Steering retaining device missing |2.2.C.1g| | 1 |
| Nearside Front Lower Front suspension retaining device missing |2.5.A.4| | 1 |
| Nearside Front Lower Suspension arm insecure |2.4.G.1| | 1 |
| Nearside Front Upper Front suspension has a suspension upper ball joint securing nut loose |2.5.B.1a| | 1 |
| Nearside Rear front parking brake recording little or no effort |3.7.B.6a| | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wing (6.2.2 (d) (i)) | 1 |
| Nearside Front Upper Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis leg (5.3.3 (b) (i)) | 1 |
| Offside Front Upper Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis leg (5.3.3 (b) (i)) | 1 |
| Offside Front Brake prescribed area is excessively corroded wheel arch / floor within 30cm pedal box (1.1.21 (e) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor/inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rusted and holed near anti roll bar and subframe mounts (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases at rear joint (6.1.2 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill at rear rusted and holed and covered in body filler (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill at rearcorroded and not attached along lower seam and covered in body filler (7.1.1 (a) (i)) | 1 |
| Rear fog lamp obviously incorrectly positioned Rear fog lamp fitted to wrong side of vehicle (4.5.4 (a)) | 1 |
| Nearside Front Service brake grabbing severely |1.2.1 |c|| | 1 |
| Offside Rear rear brake recording little or no effort park brake |3.7.B.5a| | 1 |
| Nearside Front Valve stem seriously damaged cracked / split |4.1.D.1e| | 1 |
| Offside Front Upper Suspension component ball joint likely to become detached split pin missing (5.3.4 (a) (ii)) | 1 |
| Nearside Front Passengers seat insecure bolt missing (6.2.6 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg / inner wing |2.4.A.3| | 1 |
| Offside Steering arm deformed track rod bent |2.1.3 |c| |i|| | 1 |
| Offside Front Service brake excessively binding reading 30kg |1.2.1 |f|| | 1 |
| Front Headlamp aim beam image obviously incorrect both |1.8.A.1b| | 1 |
| Headlamp lens seriously defective both |4.1.1 |b| |ii|| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill within 30cm of seat belt mounting |6.1.B.2| | 1 |
| Exhaust has a major leak of exhaust gases back box to centre section joint corroded (6.1.2 (a)) | 1 |
| Offside Front Position lamp not working side (4.2.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage fractured droplink detached |2.4.G.1| | 1 |
| Front Subframe mounting prescribed area is excessively corroded chassis both sides |2.4.A.3| | 1 |
| Nearside Front Shock absorbers insecurely attached lower bolt loose (5.3.2 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail in inner wheelarch outer and lower faces |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis rail in inner wheelarch outer and lower faces |2.4.A.3| | 1 |
| Emissions not tested due to miss fire (8.2.1.2 (d)) | 1 |
| Exhaust gas recirculation valve obviously modified (8.2.1.1 (a)) | 1 |
| Exhaust gas recirculation valve obviously defective (8.2.1.1 (a)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage insecure and impairing directional stability detached (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing area (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor area holed (7.1.1 (a) (i)) | 1 |
| Offside Front Position lamp not working side lamp |4.2.1 |a|| | 1 |
| Headlamp has a product on the light source so that the light output is severely reduced both (4.1.4 (b)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills (6.1.1 (c) (i)) | 1 |
| Parking brake lever has no reserve travel High |3.1.6b| | 1 |
| Power steering pipe/hose excessively corroded and leaking (2.1.5 (g) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floorpan (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floorpan (6.2.2 (d) (i)) | 1 |
| Electrical wiring inadequately supported in car |1.9.2a| | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch/ sill (6.2.2 (d) (i)) | 1 |
| Emissions not tested BET not met and full test not carried out due to the condition of exhaust (8.2.1.2 (d)) | 1 |
| Power steering component leaking rack area (2.1.5 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner rear sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner rear sill (7.1.1 (a) (i)) | 1 |
| Windscreen excessively tinted and visibility through swept area of windscreen seriously affected Sun strip (3.2 (b) (ii)) | 1 |
| Rear Suspension component attachment bracket/mounting insecure and impairing directional stability Bracing bar (5.3.3 (a) (ii)) | 1 |
| Nearside Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.A.1| | 1 |
| Front brake caliper has restricted free movement |3.5.1k| | 1 |
| Suspension component mounting prescribed area is excessively corroded Nearside outer sill |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill / wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill / wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt retracting mechanism defective jammed (7.1.2 (e)) | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing |6.1.B.2| | 1 |
| Nearside Parking brake inoperative on one side zero effort (1.4.1 (a)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill at middle |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded centre of outer sill |5.2.6| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect dip beam (4.1.2 (c)) | 1 |
| Driver`s airbag obviously defective warning light on |5.4.1| | 1 |
| Nearside Front Side repeater light intensity significantly reduced (4.4.3 (a)) | 1 |
| Nearside Rear Suspension arm corroded and seriously weakened lower arm corroded |2.4.G.1| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded outer sill panel |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded outer sill panel |2.4.A.3| | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Coil spring fractured or broken snapped (5.3.1 (b) (i)) | 1 |
| Offside Brake pipe leaking on an air braking system front to rear (1.1.11 (b) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension arm (5.3.6 (a) (i)) | 1 |
| Rear Fuel pipe leaking |7.2.3| | 1 |
| Emissions unable to be completed excessive exhaust leak likely to become detached (8.2.1.2 (d)) | 1 |
| Brake fluid contaminated green (1.8 (a)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch marked in yellow (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt marked in yellow (5.3.4 (b) (ii)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak Rear exhaust joint corroded/broken . from catalytic converter back needed. (8.2.1.1 (b)) | 1 |
| Brake fluid contaminated Green (1.8 (a)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced yellow chalk inner wheel arch. (6.1.1 (c) (i)) | 1 |
| Front Power steering pipe/hose corroded such that the steering is adversely affected (2.1.5 (g) (ii)) | 1 |
| Offside Front Position lamp not working 501 bulb fitted |4.2.1 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch chassie leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength quarter sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength quarter sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (within 30cm of seatbelt anchorage) (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases back box |6.1.2 |a|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Rear outer sill |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Rear outer sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded in and outer sill |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Sill (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both front chassis legs close to antiroll bar mounting points |5.3.6 |a| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Nearside Suspension component mounting prescribed area is severely distorted front to rear chassis worn through |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is severely distorted front to rear chassis worn through |2.4.A.3| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired ns sill (6.2.2 (d) (ii)) | 1 |
| Nearside Power steering ram|s| leaking from a failed component |2.3.3b| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired outer sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer+inner sills (5.3.6 (a) (i)) | 1 |