| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 4676 |
| Headlamp aim out of alignment | 4563 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 3795 |
| Registration plate lamp issues | 3635 |
| Brake pipe excessively corroded | 3379 |
| Parking brake: efficiency below requirements |3.7.B.7| | 1955 |
| Brakes imbalanced across an axle | 1760 |
| Rear parking brake recording little or no effort | 1718 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1414 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1137 |
| Registration plate issues | 1125 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1119 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 975 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 949 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 948 |
| Parking brake lever has no reserve travel |3.1.6b| | 938 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 880 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 687 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 668 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 640 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 595 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 524 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 520 |
| Offside front brake binding |3.7.B.1| | 492 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 484 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 479 |
| Rear brake disc in such a condition that it is seriously weakened | 472 |
| Offside Headlamp not working on main beam |1.7.5a| | 453 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 416 |
| Nearside front brake binding |3.7.B.1| | 407 |
| Service brake: efficiency below requirements |3.7.B.7| | 397 |
| Rear brake binding | 387 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 363 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 337 |
| Front brake application uneven | 336 |
| Nearside Headlamp not working on main beam |1.7.5a| | 333 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 330 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 305 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 299 |
| Brake hose excessively deteriorated | 290 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 272 |
| Offside Front front brake binding |3.7.B.1| | 263 |
| Offside Rear coil spring broken |2.4.C.1a| | 254 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 253 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 251 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 249 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 240 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 239 |
| Offside Rear brake caliper leaking |3.6.A.1| | 239 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 236 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 236 |
| Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 232 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 230 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 230 |
| Centre Stop lamp not working |1.2.1b| | 225 |
| Nearside Front front brake binding |3.7.B.1| | 214 |
| Front brake disc in such a condition that it is seriously weakened | 203 |
| Offside Front Anti-roll bar linkage insecure |2.4.G.1| | 195 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 193 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 191 |
| Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 185 |
| Nearside Stop lamp not working |1.2.1b| | 181 |
| Nearside Rear coil spring broken |2.4.C.1a| | 179 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 178 |
| Offside Stop lamp not working |1.2.1b| | 178 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 178 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 177 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 174 |
| Nearside Rear brake caliper leaking |3.6.A.1| | 173 |
| Mechanical brake component has restricted free movement | 172 |
| Nearside Rear brake disc excessively pitted |3.5.1h| | 166 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 165 |
| Offside Rear brake disc excessively pitted |3.5.1h| | 163 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 160 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 154 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 154 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 148 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 147 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 146 |
| Horn not working |1.6.2a| | 140 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 140 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 136 |
| Offside Front Anti-roll bar linkage fractured |2.4.G.1| | 135 |
| Offside Rear Braking system leaking |3.6.A.1| | 133 |
| Emissions not tested |7.0| | 129 |
| Rear brake application uneven | 124 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 123 |
| Windscreen washer not working | 123 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 123 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 120 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 120 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 118 |
| Offside Front brake disc excessively pitted |3.5.1h| | 118 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 118 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 117 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 114 |
| Offside Rear fog lamp not working |1.3.2b| | 113 |
| Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 112 |
| Nearside Rear Braking system leaking |3.6.A.1| | 111 |
| Offside Rear coil spring fractured |2.4.C.1a| | 107 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 106 |
| Horn not working (7.7 (a)) | 106 |
| Rear fog lamp not working |1.3.2b| | 104 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 104 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 103 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 103 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 103 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 103 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 101 |
| Power steering pipe|s| or hose|s| leaking |2.3.3b| | 101 |
| Battery insecure |1.9.1| | 101 |
| Windscreen has damage | 100 |
| Windscreen wiper blade insecure | 96 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 95 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 94 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 93 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 89 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 88 |
| Rear brake disc excessively pitted |3.5.1h| | 87 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 86 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 86 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 83 |
| Nearside Front Anti-roll bar linkage fractured |2.4.G.1| | 82 |
| Rear fog lamp tell tale not working |1.3.1b| | 81 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 81 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 80 |
| Offside Outer Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 79 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 79 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 77 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 77 |
| Supplementary Restraint System warning lamp indicates a fault |5.4.2| | 77 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 76 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 76 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 75 |
| Nearside Side repeater not working |1.4.A.2c| | 75 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 74 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 73 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 73 |
| Emissions not tested (8.2.1.2 (d)) | 72 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 72 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 72 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 69 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 68 |
| Nearside Rear Stop lamp not working |1.2.1b| | 67 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 66 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 66 |
| Emissions not tested |7.3.A.1| | 66 |
| Nearside Outer Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 65 |
| Fuel cap/sealing device missing |7.2.4a| | 65 |
| Offside Front coil spring broken |2.4.C.1a| | 64 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 64 |
| Front brake excessively fluctuating | 63 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 63 |
| Front brake disc excessively pitted |3.5.1h| | 62 |
| Offside Front Position lamp not working |4.2.1 |a|| | 62 |
| Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 61 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 61 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 60 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 60 |
| Nearside Front Service brake excessively binding |1.2.1 |f|| | 59 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 59 |
| Brake performance not tested |3.7.A.1| | 59 |
| Nearside Headlamp insecure |1.7.3| | 58 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 58 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 57 |
| Offside Rear Coil spring fractured or broken |5.3.1 |b| |i|| | 57 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 57 |
| Offside Rear coil spring incomplete |2.4.C.1a| | 57 |
| Rear Mechanical brake component has restricted free movement | 57 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 56 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 56 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 55 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 55 |
| Nearside Rear coil spring fractured |2.4.C.1a| | 54 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 54 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 54 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 54 |
| Offside Rear Stop lamp not working |1.2.1b| | 54 |
| Nearside Front coil spring broken |2.4.C.1a| | 54 |
| Offside Side repeater not working |1.4.A.2c| | 54 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 53 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 53 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 53 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 52 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 51 |
| Front position lamp|s| not working |1.1.A.3b| | 51 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 50 |
| Nearside Rear Coil spring fractured or broken |5.3.1 |b| |i|| | 50 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 50 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 50 |
| Offside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 50 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 50 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 50 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 49 |
| Offside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 49 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 48 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 48 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 48 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 47 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 47 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 46 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 46 |
| Emissions unable to be completed (8.2.1.2 (d)) | 46 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 46 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 45 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 45 |
| Nearside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 45 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 44 |
| Nearside Parking brake inoperative on one side |1.4.1 |a|| | 44 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 44 |
| Offside Headlamp insecure |1.7.3| | 44 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 43 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 43 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 43 |
| Power steering component|s| leaking |2.3.3b| | 43 |
| Offside Steering rack gaiter split |2.2.D.2d| | 42 |
| Rear Exhaust system not adequately supported |7.1.1| | 42 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 42 |
| rear parking |secondary| brakes imbalanced | 42 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 41 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 41 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 41 |
| Brake fluid warning lamp illuminated |3.6.G.2| | 41 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 40 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 40 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 40 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 40 |
| Nearside Headlamp aim not tested |1.8.A.1c| | 39 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 39 |
| Offside Front Wheel nut|s| missing |4.2.A.1e| | 39 |
| Stop lamp not working |1.2.1b| | 39 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 39 |
| Brake pipe leaking |3.6.A.1| | 39 |
| Offside Headlamp aim not tested |1.8.A.1c| | 38 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 37 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 37 |
| Exhaust carbon monoxide content at idle exceeds default limits |8.2.1.2 |b|| | 37 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 37 |
| Centre Rear Stop lamp not working |1.2.1b| | 37 |
| Anti-lock braking system warning lamp does not illuminate |3.4.1b| | 37 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 36 |
| Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 36 |
| Nearside Rear Anti-roll bar linkage insecure |2.4.G.1| | 36 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 36 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 35 |
| Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 35 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 35 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 35 |
| Main beam tell-tale not working (4.9.1 (a) (ii)) | 35 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 35 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 35 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 34 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 34 |
| Nearside Headlamp not working on main beam |4.1.1 |a| |ii|| | 34 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 34 |
| Main beam `tell-tale` not working |1.7.4c| | 34 |
| Power steering inoperative |2.3.3a| | 33 |
| Nearside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 33 |
| Exhaust catalytic converter missing where one was fitted as standard |7.1.3| | 33 |
| Offside Front coil spring fractured |2.4.C.1a| | 32 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 32 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 32 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 32 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 32 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 32 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 32 |
| Brake performance not tested (1.2.1 (g)) | 31 |
| Horn not working (7.7 (a) (ii)) | 31 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 31 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 31 |
| Brake hose damaged | 31 |
| Offside Parking brake inoperative on one side |1.4.1 |a|| | 31 |
| Nearside Rear Road wheel bead rim badly distorted |4.2.A.1a| | 31 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 30 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 30 |
| Nearside Front position lamp|s| incorrect colour |1.1.A.3e| | 30 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 30 |
| Nearside Rear Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 30 |
| front brakes release unevenly |3.7.B.4| | 29 |
| Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 29 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 29 |
| Rear Parking brake lever has no reserve travel |3.1.6b| | 29 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 29 |
| Rear fog lamp emits a light other than red |1.3.2e| | 29 |
| Nearside Rear brake disc excessively scored |3.5.1h| | 29 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 29 |
| Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 29 |
| Offside Rear Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 29 |
| Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 29 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 28 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 28 |
| Offside Rear Anti-roll bar linkage fractured |2.4.G.1| | 28 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 28 |
| Rear Rear fog lamp not working |1.3.2b| | 28 |
| Offside Rear Wheel nut|s| missing |4.2.A.1e| | 28 |
| Offside Front brake caliper has restricted free movement |3.5.1k| | 28 |
| Offside Rear Anti-roll bar linkage insecure |2.4.G.1| | 28 |
| Headlamp aim out of alignment | 27 |
| Central Stop lamp not working |1.2.1b| | 27 |
| Offside Front Shock absorbers has a serious fluid leak | 27 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 27 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 27 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 27 |
| Nearside Rear coil spring incomplete |2.4.C.1a| | 27 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 27 |
| Offside Rear Hydraulic brake calliper leaking |1.1.16 |b| |i|| | 27 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 26 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 26 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 26 |
| Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 26 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 26 |
| Offside Rear Parking brake inoperative on one side |1.4.1 |a|| | 26 |
| Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 26 |
| Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 26 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 26 |
| Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 26 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 25 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 25 |
| Drivers airbag missing (7.1.5 (a)) | 25 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 25 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 25 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 25 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.D.1| | 25 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 25 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 25 |
| Emissions not tested |8.2.1.2 |d|| | 25 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 25 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 25 |
| Nearside Front Road wheel bead rim badly distorted |4.2.A.1a| | 24 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 24 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 24 |
| Nearside Rear Shock absorbers has a serious fluid leak | 24 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 24 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 24 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 24 |
| Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 24 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 24 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 24 |
| Offside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 24 |
| Braking system leaking |3.6.A.1| | 24 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 24 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 23 |
| Offside Front Headlamp aim not tested |1.8.A.1c| | 23 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 23 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 23 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 23 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 23 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 23 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 23 |
| Parking brake: efficiency below requirements |3.7.D.4| | 23 |
| Offside Rear brake disc excessively scored |3.5.1h| | 23 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 23 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 23 |
| Exhaust system not adequately supported |7.1.1| | 22 |
| Driver`s airbag missing |5.4.1| | 22 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 22 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 22 |
| Nearside Front Coil spring fractured or broken |5.3.1 |b| |i|| | 22 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 22 |
| Nearside Front brake caliper has restricted free movement |3.5.1k| | 22 |
| Brake pedal spongy |3.3.B.1b| | 22 |
| Nearside Rear Anti-roll bar linkage fractured |2.4.G.1| | 21 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 21 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 21 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 21 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 21 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 21 |
| brake disc excessively pitted |3.5.1h| | 21 |
| Nearside Front coil spring fractured |2.4.C.1a| | 21 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 21 |
| Nearside Front Wheel nut|s| missing |4.2.A.1e| | 21 |
| Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 21 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 21 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 21 |
| Nearside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 21 |
| Offside Rear Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 21 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 21 |
| Offside Front Braking system leaking |3.6.A.1| | 21 |
| Nearside Front brake caliper leaking |3.6.A.1| | 21 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 20 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 20 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 20 |
| Nearside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 20 |
| Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 20 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 20 |
| Offside Front brake caliper leaking |3.6.A.1| | 20 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 20 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 20 |
| Nearside Front Valve stem seriously damaged |4.1.D.1e| | 20 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 20 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 20 |
| Supplementary restraint system warning lamp indicates a fault |7.1.6 |a|| | 20 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 20 |
| Offside rear brake excessively fluctuating |3.7.B.3| | 20 |
| Nearside Front Side repeater not working |1.4.A.2c| | 19 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 19 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 19 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 19 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 19 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 19 |
| Offside front brake juddering severely |3.7.A.2b| | 19 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 19 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 19 |
| Nearside Front Braking system leaking |3.6.A.1| | 19 |
| Offside Front Headlamp insecure |1.7.3| | 19 |
| Nearside Rear Wheel nut|s| missing |4.2.A.1e| | 19 |
| Nearside rear brake excessively fluctuating |3.7.B.3| | 19 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 19 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 19 |
| Offside Front Anti-roll bar insecure |2.4.G.1| | 19 |
| Offside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 19 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 19 |
| Offside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 19 |
| Nearside Front All position lamps not working |1.1.A.3b| | 19 |
| Headlamp aim not tested |1.8.A.1c| | 19 |
| Offside Rear Brake pipe leaking |3.6.A.1| | 19 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 18 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 18 |
| Rear fog lamp switch faulty |1.3.1a| | 18 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 18 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 18 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 18 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 18 |
| Offside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 18 |
| Offside Rear Braking system leaking caliper |3.6.A.1| | 18 |
| Power steering component leaking (2.1.5 (a)) | 18 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 18 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 18 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 18 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 18 |
| Offside Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 18 |
| Fuel cap/sealing device sealing washer missing |7.2.4c| | 18 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 17 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 17 |
| Brake hose has insufficient room to move | 17 |
| Offside Rear Service brake excessively binding |1.2.1 |f|| | 17 |
| Offside Rear fog lamp missing |1.3.2a| | 17 |
| Offside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 17 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 17 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 17 |
| Offside Headlamp aim not tested (4.1.2 (b)) | 17 |
| Nearside front brake juddering severely |3.7.A.2b| | 17 |
| Offside Headlamp light intensity severely reduced |4.1.4 |a|| | 17 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 17 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 17 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 17 |
| Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 17 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 17 |
| Offside Front brake disc excessively scored |3.5.1h| | 17 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 17 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 17 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 17 |
| Nearside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 17 |
| Offside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 17 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 16 |
| Offside Front All position lamps not working |1.1.A.3b| | 16 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 16 |
| Offside Rear Shock absorbers has a serious fluid leak | 16 |
| Horn not working |7.7 |a| |ii|| | 16 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 16 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 16 |
| Brake master cylinder fluid level below minimum level |3.6.G.1e| | 16 |
| Offside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 16 |
| Exhaust carbon monoxide content at idle exceeds manufacturer`s specified limits |8.2.1.2 |b|| | 16 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 16 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 16 |
| Brake lever has insufficient reserve travel |1.1.2 |a|| | 16 |
| Offside Front Anti-roll bar linkage missing |2.4.G.1| | 16 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 16 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 16 |
| Nearside Front Headlamp insecure |1.7.3| | 16 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 16 |
| Power steering pipe/hose leaking |2.1.5 |a|| | 15 |
| Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 15 |
| Power steering fluid level below minimum |2.3.1| | 15 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 15 |
| Offside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 15 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 15 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 15 |
| Nearside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 15 |
| Offside Front Direction indicator not working |1.4.A.2c| | 15 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 15 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 15 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 15 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 15 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 15 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 15 |
| Fuel cap/sealing device sealing washer deteriorated |7.2.4c| | 15 |
| Offside Outer Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 15 |
| Offside Rear Road wheel bead rim badly distorted |4.2.A.1a| | 15 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 15 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 15 |
| Offside Front Headlamp not working on main beam |4.1.1 |a| |ii|| | 15 |
| Offside Rear Valve stem seriously damaged |4.1.D.1e| | 15 |
| Nearside Front brake disc excessively scored |3.5.1h| | 15 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 15 |
| Nearside Rear Braking system leaking caliper |3.6.A.1| | 15 |
| Offside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 15 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 14 |
| Offside Rear coil spring cracked |2.4.C.1a| | 14 |
| Nearside Front Shock absorbers has a serious fluid leak | 14 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 14 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 14 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 14 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 14 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 14 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 14 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 14 |
| Rear brake disc excessively scored |3.5.1h| | 14 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 14 |
| Rear Stop lamp not working |1.2.1b| | 14 |
| Offside Front Valve stem seriously damaged |4.1.D.1e| | 14 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 14 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 14 |
| Nearside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 14 |
| Nearside Rear Valve stem seriously damaged |4.1.D.1e| | 14 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 14 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 14 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 14 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 14 |
| Offside Front An item not tested |Manual| | 14 |
| Exhaust emissions likely to be affected by an exhaust leak |8.2.1.1 |b|| | 14 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 14 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 14 |
| Offside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 14 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 14 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 14 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 14 |
| Brake pedal anti-slip provision worn smooth |3.3.A.1b| | 14 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 14 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 13 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 13 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 13 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 13 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 13 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 13 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 13 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 13 |
| Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 13 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 13 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 13 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 13 |
| rear brakes release unevenly |3.7.B.4| | 13 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 13 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 13 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 13 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 13 |
| Fuel cap/sealing device missing (6.1.3 (b) (i)) | 13 |
| Offside Front Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 13 |
| Offside Headlamp insecure (4.1.1 (c)) | 13 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 13 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 13 |
| Hazard warning switch insecure |1.4.B.1d| | 13 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 13 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 13 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 13 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 13 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 13 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 13 |
| Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 13 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 13 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 13 |
| Offside Rear brake caliper has restricted free movement |3.5.1k| | 13 |
| Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 12 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 12 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 12 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 12 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 12 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 12 |
| An item not tested |Manual| | 12 |
| Rear fog lamp missing |1.3.2a| | 12 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 12 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 12 |
| Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 12 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 12 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 12 |
| Offside Side repeater incorrect colour |1.4.A.2f| | 12 |
| Brake performance unable to be tested (1.2.1 (g)) | 12 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 12 |
| Nearside Front An item not tested |Manual| | 12 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 12 |
| Nearside Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 12 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 12 |
| Offside Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 12 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 12 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 12 |
| Nearside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 12 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 12 |
| Headlamp not working on dipped beam |1.7.5a| | 12 |
| Nearside Rear Valve stem seriously damaged (5.2.3 (j)) | 12 |
| Nearside Front Headlamp aim not tested |1.8.A.1c| | 12 |
| Offside Rear Upper Suspension arm corroded and seriously weakened |2.4.G.1| | 12 |
| Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 11 |
| Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 11 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 11 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 11 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 11 |
| Front Windscreen wiper blade deteriorated |8.2.2| | 11 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 11 |
| Offside Front Anti-roll bar fractured |2.4.G.1| | 11 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 11 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 11 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 11 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 11 |
| Offside Front Coil spring fractured or broken |5.3.1 |b| |i|| | 11 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 11 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 11 |
| Nearside Body has a sharp edge caused by damage |6.1.C.1| | 11 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 11 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 11 |
| Offside Rear rear brake juddering severely |3.7.A.5b| | 11 |
| Central Exhaust has a major leak of exhaust gases |7.1.2| | 11 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 11 |
| Offside Rear Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 11 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 11 |
| Offside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 11 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 11 |
| Front position lamp|s| incorrect colour |1.1.A.3e| | 11 |
| Nearside Rear Hydraulic brake calliper leaking |1.1.16 |b| |i|| | 11 |
| Offside Inner Front brake disc excessively pitted |3.5.1h| | 11 |
| Driver`s airbag obviously defective |5.4.1| | 11 |
| front brake binding |3.7.B.1| | 11 |
| Offside Rear Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 11 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 11 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 11 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 11 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 11 |
| Nearside Front Anti-roll bar linkage missing |2.4.G.1| | 11 |
| Nearside Rear Brake pipe leaking |3.6.A.1| | 11 |
| Registration plate lamp issues | 10 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 10 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 10 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 10 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 10 |
| Offside Front Front position lamp|s| incorrect colour |1.1.A.3e| | 10 |
| Rear rear brake recording little or no effort |3.7.B.5a| | 10 |
| Front Brake pipe leaking |3.6.A.1| | 10 |
| Offside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 10 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 10 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 10 |
| Rear Exhaust emissions likely to be affected by an exhaust leak |8.2.1.1 |b|| | 10 |
| Nearside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 10 |
| Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 10 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 10 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 10 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 10 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 10 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 10 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 10 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 10 |
| Offside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 10 |
| Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 10 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 10 |
| Offside Front Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 10 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 10 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 10 |
| Front Headlamp not working on dipped beam |1.7.5a| | 10 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 10 |
| Nearside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 10 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 10 |
| brake disc in such a condition that it is seriously weakened |3.5.1i| | 10 |
| Rear fog lamp switch missing |1.3.1a| | 10 |
| Nearside Front Valve stem seriously damaged (5.2.3 (j)) | 10 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 10 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 10 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 10 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 10 |
| Nearside Rear rear brake juddering severely |3.7.A.5b| | 10 |
| Nearside Inner Front brake disc excessively pitted |3.5.1h| | 10 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 10 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 10 |
| Offside Front Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 10 |
| Offside Rear Upper Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 10 |
| Fuel cap/sealing device sealing washer torn |7.2.4c| | 10 |
| Nearside Front Brake hose twisted |3.6.B.4c| | 10 |
| Nearside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 10 |
| Central Stop lamp|s| not working |4.3.1 |a| |ii|| | 10 |
| Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 10 |
| Nearside Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 10 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 10 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 10 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 10 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 10 |
| Front Front position lamp|s| not working |1.1.A.3b| | 10 |
| Nearside Rear Road wheel distorted |4.2.A.1a| | 10 |
| Offside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 9 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 9 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 9 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 9 |
| Nearside Front Front position lamp|s| incorrect colour |1.1.A.3e| | 9 |
| Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 9 |
| Upper Stop lamp not working |1.2.1b| | 9 |
| Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 9 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 9 |
| Offside Front Service brake lagging in operation (1.2.1 (d)) | 9 |
| rear brake excessively fluctuating |3.7.B.3| | 9 |
| Offside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 9 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 9 |
| Offside Front coil spring incomplete |2.4.C.1a| | 9 |
| Offside Front Road wheel fixing missing (5.2.1 (a) (i)) | 9 |
| Nearside Headlamp does not operate immediately when selected on dipped beam |1.7.4a| | 9 |
| Offside Front Position lamp not working |4.2.1 |a| |ii|| | 9 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 9 |
| Nearside Headlamp insecure (4.1.1 (c)) | 9 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 9 |
| Horn control missing |1.6.1| | 9 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 9 |
| Parking brake: efficiency below requirements (3.7.B.7) | 9 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 9 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 9 |
| Power steering malfunctioning (2.1.5 (a)) | 9 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 9 |
| Offside Rear Rear fog lamp missing |1.3.2a| | 9 |
| Centre Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 9 |
| Offside Front Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 9 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 9 |
| Offside Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 9 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 9 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 9 |
| Nearside Front Brake hose excessively damaged |3.6.B.4d| | 9 |
| Front Body has a sharp edge caused by damage |6.1.C.1| | 9 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 9 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 9 |
| Driver`s seat insecure |6.2.A.1| | 9 |
| Offside Front Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 9 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
| Offside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 9 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 9 |
| Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 9 |
| Offside Rear Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 9 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 9 |
| Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 9 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 9 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 9 |
| Nearside Front Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 9 |
| Nearside Rear Upper Suspension arm corroded and seriously weakened |2.4.G.1| | 9 |
| Offside Front Valve stem seriously damaged (5.2.3 (j)) | 9 |
| Windscreen wiper does not clear the windscreen effectively | 8 |
| Nearside Front Road wheel fixing missing (5.2.1 (a) (i)) | 8 |
| Offside Rear Upper Coil spring fractured or broken (5.3.1 (b) (i)) | 8 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 8 |
| Anti-lock braking system warning lamp does not illuminate (1.6 (a)) | 8 |
| Central Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 8 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 8 |
| Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 8 |
| Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 8 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a)) | 8 |
| Offside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 8 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 8 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 8 |
| Offside Front Upper Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 8 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 8 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 8 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 8 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 8 |
| rear brake recording little or no effort |3.7.B.5a| | 8 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 8 |
| Nearside Parking brake recording little or no effort |3.7.D.3a| | 8 |
| Offside Headlamp aim unable to be tested (4.1.2 (b)) | 8 |
| Nearside Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Offside Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Brake fluid contaminated (1.8 (a)) | 8 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 8 |
| Nearside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 8 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 8 |
| Rear Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 8 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 8 |
| Nearside Side repeater incorrect colour |1.4.A.2f| | 8 |
| Brake pipe leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) | 8 |
| Emissions unable to be completed (8.2.2.2 (e)) | 8 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 8 |
| Offside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 8 |
| Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 8 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 8 |
| Headlamp aim not tested (4.1.2 (b)) | 8 |
| Offside Front Brake pipe leaking |3.6.A.1| | 8 |
| Nearside Outer Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 8 |
| Offside Outer Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 8 |
| Nearside Outer Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 8 |
| Offside Brake pipe leaking |3.6.A.1| | 8 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 8 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 8 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 8 |
| Offside Front Road wheel bead rim badly distorted |4.2.A.1a| | 8 |
| Nearside Front Road wheel distorted |4.2.A.1a| | 8 |
| Anti-lock braking system warning lamp sequence is incorrect |3.4.1d| | 8 |
| Nearside Side repeater missing |1.4.A.2b| | 8 |
| Rear Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 8 |
| Exhaust engine idle speed too high |7.3.D.1| | 8 |
| Offside Rear front brake binding |3.7.B.1| | 8 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 8 |
| Brake performance not tested |1.2.1 |g|| | 8 |
| Offside Front Headlamp insecure (4.1.1 (c)) | 8 |
| Nearside Rear Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 8 |
| Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 8 |
| Windscreen wiper blade deteriorated |8.2.2| | 8 |
| Nearside Front Anti-roll bar linkage insecure and impairing directional stability |5.3.3 |a| |ii|| | 8 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 8 |
| Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Centre Rear Exhaust has a major leak of exhaust gases |7.1.2| | 8 |
| Exhaust emits excessive dense blue smoke during acceleration |7.3.A.2c| | 8 |
| Nearside rear brake juddering severely |3.7.A.5b| | 8 |
| Nearside Headlamp light intensity severely reduced |4.1.4 |a|| | 8 |
| Nearside Rear brake caliper has restricted free movement |3.5.1k| | 8 |
| Driver`s door cannot be opened from inside the vehicle |6.2.B.1b| | 8 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 8 |
| Offside Rear Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 8 |
| Nearside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 8 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 7 |
| Offside Front Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 7 |
| Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 7 |
| Fuel cap/sealing device missing |6.1.3 |b| |i|| | 7 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 7 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 7 |
| Nearside Rear coil spring cracked |2.4.C.1a| | 7 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 7 |
| Nearside Front Road wheel badly damaged |4.2.A.1a| | 7 |
| Rear Brake pipe leaking |3.6.A.1| | 7 |
| Offside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 7 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 7 |
| Nearside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 7 |
| Nearside Rear position lamp|s| incorrect colour |1.1.A.3e| | 7 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 7 |
| Rear fog lamp switch missing (4.5.3 (a)) | 7 |
| Offside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 7 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 7 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 7 |
| Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 7 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 7 |
| Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 7 |
| Direction indicators not working |1.4.A.2c| | 7 |
| Hazard warning lamps inoperative |1.4.B.1b| | 7 |
| Nearside Front coil spring incomplete |2.4.C.1a| | 7 |
| Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 7 |
| Offside Headlamp does not operate immediately when selected on dipped beam |1.7.4a| | 7 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 7 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 7 |
| Offside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 7 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 7 |
| Hazard warning switch faulty |1.4.B.1d| | 7 |
| Nearside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 7 |
| Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 7 |
| Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 7 |
| Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 7 |
| Offside Front Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 7 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 7 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 7 |
| Rear fog lamp tell tale missing |1.3.1b| | 7 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 7 |
| Steering system excessively rough |2.2.D.1| | 7 |
| Offside Rear Valve stem seriously damaged (5.2.3 (j)) | 7 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 7 |
| Offside Indicator tell tale inoperative |1.4.A.2a| | 7 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 7 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 7 |
| Nearside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 7 |
| Nearside Rear Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 7 |
| Offside Rear Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 7 |
| Oil leaking excessively from engine |8.4.1 |a| |i|| | 7 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 7 |
| Offside Body has a sharp edge caused by damage |6.1.C.1| | 7 |
| Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 7 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 7 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 7 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 7 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 7 |
| Nearside Front Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 7 |
| Offside Front Service brake excessively fluctuating |1.2.1 |e|| | 7 |
| Offside Rear position lamp|s| incorrect colour |1.1.A.3e| | 7 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 7 |
| Headlamp levelling device inoperative (4.1.5 (a)) | 7 |
| Centre Exhaust system not adequately supported |7.1.1| | 7 |
| Centre Rear Upper Stop lamp not working |1.2.1b| | 7 |
| Offside Front Headlamp aim not tested (4.1.2 (b)) | 7 |
| Nearside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 7 |
| Offside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 7 |
| Nearside Front Side repeater incorrect colour |1.4.A.2f| | 7 |
| Offside Front Lower Ball joint has excessive play |2.2.B.1f| | 7 |
| Horn sounds harsh or grating |1.6.2e| | 7 |
| Centre Brake pipe leaking |3.6.A.1| | 7 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 7 |
| Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 7 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 7 |
| Offside Front Side repeater not working |1.4.A.2c| | 7 |
| Offside rear brake juddering severely |3.7.A.5b| | 7 |
| Nearside Front Service brake indicates brake bind |3.7.D.2a| | 7 |
| Offside Windscreen wiper not operating automatically when switched on |8.2.1b| | 7 |
| Anti-lock braking system warning lamp does not illuminate |1.6 |a|| | 7 |
| Central Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 7 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 7 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 7 |
| Offside Rear rear brake excessively fluctuating |3.7.B.3| | 7 |
| Offside Front Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 7 |
| Headlamp not working on main beam |1.7.5a| | 7 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 6 |
| Brake pipe excessively corroded | 6 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 6 |
| Central Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 6 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 6 |
| Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 6 |
| Nearside Parking brake lever has no reserve travel |3.1.6b| | 6 |
| Nearside Rear Road wheel badly damaged |4.2.A.1a| | 6 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Power steering malfunctioning |2.3.3a| | 6 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 6 |
| Power steering component leaking |2.1.5 |a|| | 6 |
| Nearside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 6 |
| Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 6 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 6 |
| Parking (secondary brake) on a single line braking system imbalanced across an axle Axle 1 (1.3.1 (b) (i)) | 6 |
| Front brake disc excessively scored |3.5.1h| | 6 |
| Nearside Rear Stop lamp emits other than a steady red light |1.2.1e| | 6 |
| Offside Rear Anti-roll bar linkage missing |2.4.G.1| | 6 |
| Offside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Nearside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Offside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 6 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 6 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 6 |
| Offside Front Ball joint has excessive play |2.2.B.1f| | 6 |
| Rear fog lamp tell-tale missing (4.9.1 (a) (ii)) | 6 |
| Offside Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 6 |
| Power steering inoperative (2.1.5 (c) (i)) | 6 |
| Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 6 |
| Horn sound not in accordance with requirements (7.7 (c)) | 6 |
| Offside Seat belt anchorage prescribed area is fractured |5.2.6| | 6 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 6 |
| All position lamps not working |1.1.A.3b| | 6 |
| Nearside Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 6 |
| Nearside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 6 |
| Nearside Front Seat belt not functioning as intended (7.1.2 (c)) | 6 |
| Offside Front Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 6 |
| Offside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 6 |
| Headlamp aim unable to be tested (4.1.2 (b)) | 6 |
| Offside Front Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 6 |
| Offside Headlamp levelling device inoperative (4.1.5 (a)) | 6 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 6 |
| Offside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 6 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 6 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 6 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill |7.1.1 |a| |i|| | 6 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 6 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 6 |
| Nearside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 6 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 6 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 6 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Offside Rear Rear fog lamp does not emit a steady red light |1.3.2e| | 6 |
| Offside Front Outer Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 6 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 6 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 6 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 6 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 6 |
| Offside Front Headlamp light intensity severely reduced |4.1.4 |a|| | 6 |
| Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 6 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 6 |
| Front Position lamp not working (4.2.1 (a) (ii)) | 6 |
| Headlamp aim beam image obviously incorrect |1.8.A.1b| | 6 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 6 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 6 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 6 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 6 |
| Offside Headlamp not in good working order |not working| |1.2.4a| | 6 |
| Offside Rear Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 6 |
| Nearside Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 6 |
| Offside Front front brake juddering severely |3.7.A.2b| | 6 |
| Offside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 6 |
| Front front brake binding |3.7.B.1| | 6 |
| Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 6 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 6 |
| Nearside Rear Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 6 |
| Nearside Steering rack gaiter insecure |2.2.D.2d| | 6 |
| Offside Front Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 6 |
| Nearside Rear Rear position lamp|s| incorrect colour |1.1.A.3e| | 6 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 6 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 6 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 6 |
| Central Rear Stop lamp not working |1.2.1b| | 6 |
| Fuel system component leaking |7.2.3| | 6 |
| Nearside Rear front brake binding |3.7.B.1| | 6 |
| Brake fluid significantly below minimum mark |1.1.10 |d| |ii|| | 6 |
| Nearside Front Headlamp not working on main beam |4.1.1 |a| |ii|| | 6 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 6 |
| Offside Front Suspension arm corroded and seriously weakened |2.4.G.1| | 6 |
| Nearside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 6 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 6 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 6 |
| Offside Front Tie bar/rod insecure |2.4.G.1| | 6 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 6 |
| Offside Rear Parking brake lever has no reserve travel |3.1.6b| | 6 |
| Centre Upper Stop lamp not working |1.2.1b| | 6 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 6 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 6 |
| Nearside Front Anti-roll bar linkage severely distorted |2.4.G.1| | 6 |
| Offside Front Side repeater incorrect colour |1.4.A.2f| | 6 |
| Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 6 |
| Nearside Rear Upper Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 6 |
| Offside Front Anti-roll bar linkage cracked |2.4.G.1| | 6 |
| Steering system excessively tight |2.2.D.1| | 6 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 6 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 6 |
| Rear Exhaust has a part missing |7.1.1a| | 6 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 6 |
| Brake pedal has insufficient reserve travel |1.1.2 |a|| | 6 |
| Nearside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 6 |
| Rear Service brake excessively fluctuating (1.2.1 (e)) | 6 |
| Nearside Windscreen wiper not operating automatically when switched on |8.2.1b| | 6 |
| Nearside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 6 |
| Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 6 |
| Rear Braking system leaking |3.6.A.1| | 6 |
| Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 6 |
| Headlamp switch faulty |1.7.1| | 6 |
| Nearside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 6 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 6 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 5 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 5 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 5 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 5 |
| Offside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 5 |
| Nearside Headlamp not in good working order |not working| |1.2.4a| | 5 |
| Offside Headlamp does not operate immediately when selected on main beam |1.7.4a| | 5 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 5 |
| Nearside Anti-roll bar linkage insecure |2.4.G.1| | 5 |
| Rear Service brake excessively fluctuating |1.2.1 |e|| | 5 |
| Nearside Rear Body has a projection caused by corrosion |6.1.C.1| | 5 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 5 |
| Nearside Rear Anti-roll bar fractured |2.4.G.1| | 5 |
| Driver`s airbag missing |7.1.5 |a|| | 5 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 5 |
| Rear Exhaust system insecure (6.1.2 (a)) | 5 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 5 |
| Front Bumper insecure (6.1.4 (a) (i)) | 5 |
| Offside Obligatory mirror missing (3.3 (a)) | 5 |
| Nearside Front Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 5 |
| Rear fog lamp obviously incorrectly positioned (4.5.4 (a)) | 5 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 5 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 5 |
| Offside Front Headlamp incorrect colour |1.7.5b| | 5 |
| Offside Side repeater incorrect colour (4.4.3 (a)) | 5 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
| Offside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 5 |
| Nearside Front Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 5 |
| Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 5 |
| Nearside Rear Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Exhaust emits dense blue smoke at idle (8.2.1.2 (f)) | 5 |
| Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 5 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Front Service brake excessively fluctuating (1.2.1 (e)) | 5 |
| Hazard warning lamps inoperative (4.4.1 (e)) | 5 |
| Nearside Front Brake hose excessively stretched (1.1.12 (b) (ii)) | 5 |
| Nearside Front Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 5 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 5 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 5 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 5 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 5 |
| Nearside Rear Hydraulic brake calliper leaking and braking performance affected |1.1.16 |b| |ii|| | 5 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill |7.1.1 |a| |i|| | 5 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 5 |
| Nearside Rear rear brake grabbing severely |3.7.A.5b| | 5 |
| Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 5 |
| Fuel cap/sealing device ineffective |6.1.3 |b| |i|| | 5 |
| Service brake: efficiency below requirements |3.7.C.1a| | 5 |
| Windscreen wiper not operating automatically when switched on |8.2.1b| | 5 |
| Front position lamp|s| not working both |1.1.A.3b| | 5 |
| Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 5 |
| Exhaust catalytic converter missing where one was fitted as standard |8.2.1.1 |a|| | 5 |
| Nearside Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 5 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 5 |
| Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 5 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 5 |
| Exhaust has a part missing |7.1.1a| | 5 |
| Offside Rear Rear position lamp|s| incomplete |1.1.4a| | 5 |
| Offside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 5 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail |5.3.6 |a| |i|| | 5 |
| Nearside Front Upper Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Nearside Front Anti-roll bar insecure |2.4.G.1| | 5 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 5 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 5 |
| Nearside Front Position lamp not working |4.2.1 |a| |ii|| | 5 |
| Nearside Headlamp does not operate immediately when selected on main beam |1.7.4a| | 5 |
| Headlamp has a product on the lens so that the light output is severely reduced both |1.7.5a| | 5 |
| Offside Rear Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Offside Front Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 5 |
| Nearside Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 5 |
| Rear Upper Stop lamp not working |1.2.1b| | 5 |
| Offside Front Seat belt buckle not functioning as intended (7.1.2 (d)) | 5 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Nearside Rear brake disc contaminated by brake fluid |3.5.1h| | 5 |
| Nearside Front Brake hose stretched |found during steering lock to lock check| |2.2.D.2b| | 5 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 5 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 5 |
| Offside Outer Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 5 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 5 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 5 |
| Offside Front Position lamp light intensity significantly reduced |4.2.3 |a| |ii|| | 5 |
| Nearside Rear Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 5 |
| Rear Brake performance not tested |3.7.A.1| | 5 |
| Nearside Front Headlamp insecure (4.1.1 (c)) | 5 |
| Offside Front Anti-roll bar locating pin insecure |2.4.G.3a| | 5 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 5 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 5 |
| Offside Front Anti-roll bar ball joint excessively worn |5.3.4 |a| |i|| | 5 |
| Nearside Rear Road wheel badly distorted (5.2.2 (c) (i)) | 5 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 5 |
| Offside Headlamp incorrect colour |1.7.5b| | 5 |
| Offside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Offside Rear Body has a projection caused by corrosion |6.1.C.1| | 5 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 5 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 5 |
| Nearside Front Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 5 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 5 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 5 |
| Offside Front Anti-roll bar linkage insecure and impairing directional stability |5.3.3 |a| |ii|| | 5 |
| Offside Front Seat belt stitching badly frayed |5.2.2b| | 5 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 5 |
| Nearside Headlamp incorrect colour |1.7.5b| | 5 |
| Offside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Nearside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 5 |
| Nearside Front Suspension arm corroded and seriously weakened |2.4.G.1| | 5 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg (5.3.6 (a) (i)) | 5 |
| Offside Rear Road wheel badly damaged |4.2.A.1a| | 5 |
| Nearside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside rear brake grabbing severely |3.7.A.5b| | 5 |
| Nearside front brake recording little or no effort |3.7.B.5a| | 5 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 5 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 5 |
| Offside Front Brake hose excessively twisted (1.1.12 (b) (ii)) | 5 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Nearside Front Headlamp light intensity severely reduced |4.1.4 |a|| | 5 |
| Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 5 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 5 |
| Bonnet cannot be secured in the closed position |8.4.1| | 5 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 5 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 5 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Offside Front Hydraulic brake calliper leaking |1.1.16 |b| |i|| | 5 |
| Nearside Rear Position lamp not working |4.2.1 |a|| | 5 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Front Shock absorber has an excessively worn bush |2.7.4| | 5 |
| Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 5 |
| Nearside Brake cable has restricted free movement |3.5.1k| | 5 |
| Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction |3.1 |a| |ii|| | 5 |
| Nearside Front Headlamp aim unable to be tested (4.1.2 (b)) | 5 |
| Nearside Rear rear brake excessively fluctuating |3.7.B.3| | 5 |
| Front Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 5 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 5 |
| Nearside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 5 |
| Nearside Front Service brake lagging in operation (1.2.1 (d)) | 5 |
| Power steering pump drive system missing |2.3.6| | 5 |
| Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 5 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 5 |
| Nearside Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 5 |
| Brake pedal anti-slip provision loose |3.3.A.1b| | 5 |
| Offside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 5 |
| Front Service brake application uneven across the axle |3.7.D.2b| | 5 |
| Nearside Front All position lamps not working |4.2.1 |a|| | 5 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 5 |
| Nearside Front Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 5 |
| Nearside Front Brake hose excessively twisted (1.1.12 (b) (ii)) | 4 |
| Front Braking system leaking |3.6.A.1| | 4 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 4 |
| Brakes imbalanced across an axle | 4 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 4 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 4 |
| Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 4 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 4 |
| Offside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 4 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 4 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 4 |
| Nearside Rear Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 4 |
| Nearside Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 4 |
| Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 4 |
| Offside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 4 |
| Nearside Rear Anti-roll bar linkage missing |2.4.G.1| | 4 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Nearside Front Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 4 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 4 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 4 |
| Offside Front Anti-roll bar linkage missing (5.3.3 (a) (ii)) | 4 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.2.1 (a)) | 4 |
| Nearside Rear Parking |secondary brake| on a single line braking system has inadequate effort at a wheel |1.3.1 |a| |i|| | 4 |
| Offside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Windscreen wiper not working (3.4 (a)) | 4 |
| Brake pedal creeps down under servo assistance and touches the floor |3.3.C.3| | 4 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 4 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 4 |
| Oil leaking continuously from engine posing a serious risk to road safety (8.4.1 (a) (ii)) | 4 |
| Nearside Side repeater missing (4.4.1 (a) (ii)) | 4 |
| Emissions unable to be completed Due to exhaust leak (8.2.1.2 (d)) | 4 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 4 |
| Exhaust emits dense blue smoke at idle |7.3.A.2b| | 4 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 4 |
| Nearside Side repeater incorrect colour (4.4.3 (a)) | 4 |
| Offside Rear fog lamp insecure |1.3.2a| | 4 |
| Offside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3) | 4 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Nearside Front Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 4 |
| Rear fog lamp insecure |1.3.2a| | 4 |
| Drivers seat fore and aft adjustment mechanism not functioning as intended. (6.2.5 (b) (i)) | 4 |
| Nearside Front Direction indicators not working |1.4.A.2c| | 4 |
| Brake master cylinder leaking (1.1.10 (b) (ii)) | 4 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 4 |
| Offside Front Brake hose excessively stretched (1.1.12 (b) (ii)) | 4 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 4 |
| front brake juddering severely |3.7.A.2b| | 4 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 4 |
| Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
| Nearside Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 4 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 4 |
| Headlamp not working on dipped beam both (4.1.1 (a) (ii)) | 4 |
| Front Service brake excessively binding both (1.2.1 (f)) | 4 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 4 |
| Nearside Outer Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill area |2.4.A.3| | 4 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 4 |
| Nearside Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 4 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill |6.2.2 |d| |i|| | 4 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 4 |
| Offside Front Headlamp insecure |4.1.1 |c|| | 4 |
| Nearside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Front Service brake excessively fluctuating |1.2.1 |e|| | 4 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 4 |
| Offside Front Headlamp adversely affected by the operation of another lamp |1.7.5c| | 4 |
| Nearside Rear Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 4 |
| Nearside Front Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 4 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 4 |
| Nearside Side repeater not working |4.4.1 |a| |ii|| | 4 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 4 |
| Offside front brake recording little or no effort |3.7.B.5a| | 4 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 4 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 4 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 4 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 4 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 4 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 4 |
| Rear Brake lever has insufficient reserve travel (1.1.2 (a)) | 4 |
| Power steering component|s| leaking from a failed seal |2.3.3b| | 4 |
| Power steering pump drive system defective |2.3.6| | 4 |
| Headlamps matched pair are not the same colour |1.7.6| | 4 |
| Centre Front Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 4 |
| Offside Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 4 |
| Offside Front Side repeater not working |4.4.1 |a| |ii|| | 4 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 4 |
| Nearside All position lamps not working |1.1.A.3b| | 4 |
| Rear Brake pipe inadequately clipped |3.6.B.1| | 4 |
| Nearside Front Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 4 |
| Rear Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 4 |
| Nearside Rear Brake pipe inadequately supported |3.6.B.1| | 4 |
| Offside Front Road wheel cracked |4.2.A.1a| | 4 |
| Nearside Front front brake juddering severely |3.7.A.2b| | 4 |
| Nearside Front Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 4 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 4 |
| Offside Front Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 4 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 4 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch |6.1.B.2| | 4 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Service brake efficiency less than 50% of the required value |1.2.2 |a| |ii|| | 4 |
| Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 4 |
| Front Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 4 |
| Offside Rear position lamp|s| incomplete |1.1.4a| | 4 |
| Offside Front Anti-roll bar linkage rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 4 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 4 |
| Offside Front Anti-roll bar linkage attachment bracket/mounting fractured |5.3.3 |b| |ii|| | 4 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 4 |
| Emissions not tested exhaust leak (8.2.1.2 (d)) | 4 |
| Nearside Front Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 4 |
| Nearside Power steering component|s| leaking |2.3.3b| | 4 |
| Offside Power steering component|s| leaking |2.3.3b| | 4 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 4 |
| Offside Front Road wheel distorted |4.2.A.1a| | 4 |
| Offside Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 4 |
| Offside Rear Parking |secondary brake| on a single line braking system has inadequate effort at a wheel |1.3.1 |a| |i|| | 4 |
| Offside Front Headlamp aim unable to be tested (4.1.2 (b)) | 4 |
| Offside Rear Brake hose leaking |3.6.A.1| | 4 |
| Front Power steering pipe/hose leaking (2.1.5 (a)) | 4 |
| Nearside Front Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 4 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 4 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 4 |
| Rear fog lamp switch missing (4.5.3 (a) (ii)) | 4 |
| Centre Rear fog lamp not working |1.3.2b| | 4 |
| Offside Front Tie bar/rod fractured |2.4.G.1| | 4 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 4 |
| Centre Parking brake lever has no reserve travel |3.1.6b| | 4 |
| Nearside Front Headlamp adversely affected by the operation of another lamp |1.7.5c| | 4 |
| Offside Front Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 4 |
| Offside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 4 |
| Nearside Front Service brake excessively fluctuating |1.2.1 |e|| | 4 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 4 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 4 |
| Offside Rear rear brakes release unevenly |3.7.B.4| | 4 |
| Offside Stop lamp emits other than a steady red light |1.2.1e| | 4 |
| Offside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 4 |
| Body has a sharp edge caused by damage |6.1.C.1| | 4 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 4 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 4 |
| Offside Front Lower Anti-roll bar linkage insecure |2.4.G.1| | 4 |
| Steering wheel in a condition that hampers proper control |2.1.1| | 4 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 4 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 4 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 4 |
| Power steering component|s| leaking from a failed joint |2.3.3b| | 4 |
| Front front brake juddering severely |3.7.A.2b| | 4 |
| Nearside Front Anti-roll bar missing |2.4.G.1| | 4 |
| Offside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 4 |
| Nearside Outer Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Front Anti-roll bar linkage synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
| Nearside Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 4 |
| Nearside Front Power steering pipe/hose leaking (2.1.5 (a)) | 4 |
| Nearside Rear Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 4 |
| Offside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Central Rear Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
| Offside Outer Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 4 |
| Nearside Front Brake pipe leaking |3.6.A.1| | 4 |
| Offside Front Service brake indicates brake bind |3.7.D.2a| | 4 |
| Nearside Front Brake pipe twisted |found during steering lock to lock check| |2.2.D.2b| | 4 |
| Nearside Outer Rear brake disc excessively pitted |3.5.1h| | 4 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 4 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 4 |
| Nearside Rear Road wheel cracked |4.2.A.1a| | 4 |
| Offside Rear Anti-roll bar linkage fractured |5.3.3 |b| |ii|| | 4 |
| Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 4 |
| Offside Outer Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 4 |
| Nearside Rear Braking system leaking brake caliper |3.6.A.1| | 4 |
| Brake pipe inadequately supported |3.6.B.1| | 4 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 4 |
| Nearside Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 4 |
| Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Power steering inoperative and steering adversely affected (2.1.5 (c) (ii)) | 4 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 4 |
| Offside Rear Road wheel distorted |4.2.A.1a| | 4 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 4 |
| Nearside Rear Valve stem seriously damaged |5.2.3 |j|| | 4 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 4 |
| Nearside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 4 |
| Offside Front Upper Anti-roll bar linkage insecure |2.4.G.1| | 4 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 4 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 4 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 4 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 4 |
| Nearside Rear Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 4 |
| Offside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 4 |
| Offside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 4 |
| Nearside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 4 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 4 |
| Offside Rear Brake hose excessively damaged |3.6.B.4d| | 4 |
| Offside Parking brake recording little or no effort |3.7.D.3a| | 4 |
| Offside Front Lower Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 4 |
| Offside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 4 |
| Rear Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 4 |
| Nearside Rear Front position lamp|s| not working |1.1.A.3b| | 4 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 4 |
| Offside Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 4 |
| Power steering inoperative and steering adversely affected |2.1.5 |c| |ii|| | 4 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail |5.3.6 |a| |i|| | 4 |
| Offside Rear Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 4 |
| Offside Steering rack gaiter insecure |2.2.D.2d| | 4 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 4 |
| Nearside Rear Upper coil spring broken |2.4.C.1a| | 4 |
| Offside Headlamp aim not tested |4.1.2 |b|| | 4 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 4 |
| Rear Exhaust system insecure |6.1.2 |a|| | 4 |
| Offside Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 4 |
| Front front brakes release unevenly |3.7.B.4| | 4 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 4 |
| Nearside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 4 |
| Nearside Front Shock absorber has an excessively worn bush |2.7.4| | 4 |
| Nearside Rear Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 4 |
| Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 4 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 4 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 4 |
| Offside Rear Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 4 |
| Offside Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 4 |
| Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Rear fog lamp emits a light other than red |1.3.2e| | 3 |
| Registration plate issues | 3 |
| Rear brake binding | 3 |
| Rear Mechanical brake component has restricted free movement | 3 |
| Anti-lock braking system warning lamp indicates an ABS fault | 3 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Horn not working (7.7 (a)) | 3 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill/floor |5.2.6| | 3 |
| Nearside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 3 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced chassis rail (7.1.1 (a) (i)) | 3 |
| Offside Rear Inner Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 3 |
| Rear fog lamp tell-tale not working |4.9.1 |a| |ii|| | 3 |
| Nearside Stop lamp emits other than a steady red light |1.2.1e| | 3 |
| Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 3 |
| Offside Braking system leaking |3.6.A.1| | 3 |
| Offside Parking brake lever has no reserve travel |3.1.6b| | 3 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Nearside Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Offside Front Anti-roll bar linkage likely to become detached |5.3.3 |a| |ii|| | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 3 |
| Power steering component leaking steering rack (2.1.5 (a)) | 3 |
| Offside Rear Direction indicators not working |1.4.A.2c| | 3 |
| Front All position lamps not working |1.1.A.3b| | 3 |
| Centre Rear Parking brake lever has no reserve travel |3.1.6b| | 3 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 3 |
| Parking brake lever defective so that it cannot be satisfactorily operated |3.1.3c| | 3 |
| Nearside Front Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 3 |
| Offside Front Anti-roll bar linkage fractured |5.3.3 |b| |ii|| | 3 |
| Hazard warning switch inoperative (4.4.2 (a) (ii)) | 3 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Offside Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Front Anti-roll bar locating pin insecure |2.4.G.3a| | 3 |
| Offside Front Tie bar/rod attachment bracket/mounting insecure |2.4.G.1| | 3 |
| Offside Front Brake hose excessively damaged |3.6.B.4d| | 3 |
| Offside Track rod end loose |2.2.B.1d| | 3 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 3 |
| Nearside Front Anti-roll bar linkage missing (5.3.3 (a) (ii)) | 3 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt split (2.1.3 (g) (ii)) | 3 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 3 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 3 |
| Nearside Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 3 |
| Front Brake disc significantly and obviously worn both (1.1.14 (a) (i)) | 3 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 3 |
| Offside Front Seat belt not functioning as intended (7.1.2 (c)) | 3 |
| Central Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Rear Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 3 |
| Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 3 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 3 |
| Nearside Headlamp aim beam image kick up to the offside |1.6.B1| | 3 |
| Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
| Offside Front suspension has a suspension lower ball joint securing nut not locked |2.5.B.1a| | 3 |
| Offside Front Lower Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Nearside Front Headlamp incorrect colour |1.7.5b| | 3 |
| Nearside Headlamp levelling device inoperative (4.1.5 (a)) | 3 |
| Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 3 |
| Brake master cylinder leaking hydraulic fluid |3.6.G.1f| | 3 |
| Nearside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 3 |
| Emissions unable to be completed exhaust blowing (8.2.1.2 (d)) | 3 |
| Offside Seat belt retracting mechanism defective (7.1.2 (e)) | 3 |
| Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 3 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure (5.3.3 (a) (i)) | 3 |
| Offside Front Lower Suspension arm locating pin locking device missing |2.4.G.3b| | 3 |
| Front Position lamp not working both (4.2.1 (a) (ii)) | 3 |
| Steering wheel has movement relative to the column indicating looseness (2.2.1 (a) (i)) | 3 |
| Steering wheel has excessive movement up and down (2.2.2 (a)) | 3 |
| Nearside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 3 |
| Nearside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 3 |
| Nearside Rear brake disc has restricted free movement |3.5.1j| | 3 |
| Offside Rear brake disc has restricted free movement |3.5.1j| | 3 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |8.1.1 |a|| | 3 |
| Nearside Front Lower Anti-roll bar linkage insecure |2.4.G.1| | 3 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 3 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 3 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3) | 3 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 3 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 3 |
| Rear fog lamp does not emit a steady red light |1.3.2e| | 3 |
| Offside Rear Exhaust system not adequately supported |7.1.1| | 3 |
| Offside Windscreen wiper not working (3.4 (a)) | 3 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 3 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 3 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 3 |
| Central Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Offside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 3 |
| All direction indicators not working (4.4.1 (a) (ii)) | 3 |
| Nearside Front Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 3 |
| Offside Floor excessively deteriorated (6.2.4 (a) (i)) | 3 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 3 |
| Offside Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 3 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 3 |
| Nearside Front Body panel insecure wing (6.2.1 (a) (i)) | 3 |
| Rear Rear fog lamp missing |1.3.2a| | 3 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 3 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 3 |
| Exhaust mounting missing |7.1.1b| | 3 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 3 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 3 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 3 |
| Rear fog lamp has less than 50% of the light sources illuminating |1.3.2b| | 3 |
| Offside Rear Brake hose connection leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 3 |
| Brake pedal anti-slip provision missing |1.1.2 |c|| | 3 |
| Nearside Headlamp not in a clean condition affecting beam image |1.2.4a| | 3 |
| Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 3 |
| Rear fog lamp adversely affected by the operation of another lamp (4.5.4 (b)) | 3 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 3 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Anti-roll bar linkage severely distorted |2.4.G.1| | 3 |
| Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 3 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 3 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 3 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 3 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
| Offside Rear Brake pipe leaking on an air braking system (1.1.11 (b) (i)) | 3 |
| Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill panel |2.4.A.3| | 3 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill |6.2.2 |d| |i|| | 3 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 3 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Offside Rear Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 3 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis (6.2.2 (d) (i)) | 3 |
| Offside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Rear Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 3 |
| Nearside Front Outer Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 3 |
| Nearside front parking brake recording little or no effort |3.7.B.6a| | 3 |
| Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Rear Brake cable insecure | 3 |
| Nearside Front Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 3 |
| Offside Rear Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 3 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 3 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 3 |
| Offside Front Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 3 |
| Nearside Front Headlamp aim not tested (4.1.2 (b)) | 3 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 3 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 3 |
| Nearside Front Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 3 |
| Offside Front coil spring cracked |2.4.C.1a| | 3 |
| Nearside Upper Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Rear Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 3 |
| Offside Rear Seat belt anchorage prescribed area is severely distorted |5.2.6| | 3 |
| Offside Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 3 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 3 |
| Speedometer clearly inoperative |6.7.2| | 3 |
| Nearside Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 3 |
| Nearside Front Hydraulic brake calliper leaking |1.1.16 |b| |i|| | 3 |
| Nearside Front Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 3 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded sill/floor |5.2.6| | 3 |
| Nearside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 3 |
| Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 3 |
| Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 3 |
| Centre Front Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Central Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 3 |
| Main beam tell-tale not working |4.9.1 |a| |ii|| | 3 |
| Nearside Front Steering system lock to lock check twists a brake hose |2.2.D.2b| | 3 |
| Offside Seat belt anchorage prescribed area is excessively corroded chassis |5.2.6| | 3 |
| Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 3 |
| Rear Rear fog lamp emits a light other than red |1.3.2e| | 3 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 3 |
| Offside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Outer Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 3 |
| Nearside Rear Exhaust system not adequately supported |7.1.1| | 3 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
| Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Front Brake hose stretched |found during steering lock to lock check| |2.2.D.2b| | 3 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 3 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 3 |
| Nearside Rear All position lamps not working |1.1.A.3b| | 3 |
| Offside Front Seat belt insecurely fixed to the seat |5.2.1a| | 3 |
| Nearside Front Vehicle structure has an inadequate repair which adversely affects braking or steering |6.1.A.1| | 3 |
| Central Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 3 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 3 |
| Nearside Front Power steering component leaking (2.1.5 (a)) | 3 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 3 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 3 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Offside Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 3 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Rear coil spring incomplete |2.4.C.1a| | 3 |
| Offside Front Brake hose excessively twisted |1.1.12 |b| |ii|| | 3 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 3 |
| Offside Front Valve stem seriously damaged |5.2.3 |j|| | 3 |
| Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 3 |
| Nearside Front Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 3 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 3 |
| Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 3 |
| Nearside Front Side repeater missing |1.4.A.2b| | 3 |
| Nearside Front Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 3 |
| Nearside Front Side repeater not working |4.4.1 |a| |ii|| | 3 |
| Front Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 3 |
| Offside Windscreen wiper not working |3.4 |a|| | 3 |
| Nearside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Front brake disc has restricted free movement |3.5.1j| | 3 |
| Nearside Rear Service brake excessively fluctuating |1.2.1 |e|| | 3 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 3 |
| Offside Rear front parking brake recording little or no effort |3.7.B.6a| | 3 |
| Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 3 |
| Horn not loud enough to be heard by another road user |1.6.2b| | 3 |
| Nearside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Front Brake performance not tested |3.7.A.1| | 3 |
| Offside Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 3 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 3 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 3 |
| Offside Seat belt anchorage prescribed area is excessively corroded centre floor |5.2.6| | 3 |
| Brake pedal does not operate a brake fitted to each wheel |3.3.A.3| | 3 |
| Nearside Rear Parking brake lever has no reserve travel |3.1.6b| | 3 |
| Nearside Front Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg (5.3.6 (a) (i)) | 3 |
| Nearside Track rod end loose |2.2.B.1d| | 3 |
| Nearside Front Lower Shock absorbers insecurely attached (5.3.2 (a) (i)) | 3 |
| Nearside Front Power steering pipe/hose leaking |2.1.5 |a|| | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 3 |
| Drivers door cannot be opened from inside the vehicle (6.2.3 (a)) | 3 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis (5.3.6 (a) (ii)) | 3 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis (5.3.6 (a) (ii)) | 3 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch |5.3.6 |a| |i|| | 3 |
| Offside Rear Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 3 |
| Nearside Front Position lamp light intensity significantly reduced |4.2.3 |a| |ii|| | 3 |
| Offside Front front brake grabbing severely |3.7.A.2b| | 3 |
| Nearside rear brake grabbing severely |3.7.A.5b| | 3 |
| Nearside Front brake disc has restricted free movement |3.5.1j| | 3 |
| Offside Front Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 3 |
| Offside Front Anti-roll bar linkage attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 3 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 3 |
| Offside Front Suspension component mounting prescribed area is fractured |2.4.A.3| | 3 |
| Offside Rear Upper coil spring broken |2.4.C.1a| | 3 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 3 |
| Power steering pipe|s| or hose|s| leaking from a seal |2.3.3b| | 3 |
| Nearside Front Steering rack insecure |2.2.B.1a| | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner arch |5.2.6| | 3 |
| Rear Exhaust has a major leak of exhaust gases box (6.1.2 (a)) | 3 |
| Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 3 |
| Power steering pump leaking from a failed component |2.3.3b| | 3 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 3 |
| Nearside Rear Seat belt anchorage prescribed area is fractured |5.2.6| | 3 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 3 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 3 |
| Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 3 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 3 |
| Nearside Seat belt retracting mechanism defective |5.2.5b| | 3 |
| Offside Seat belt retracting mechanism defective |5.2.5b| | 3 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 3 |
| Offside Rear Anti-roll bar insecure |2.4.G.1| | 3 |
| Offside Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Centre Rear Brake pipe leaking |3.6.A.1| | 3 |
| Rear Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 3 |
| Offside Side repeater not working |4.4.1 |a| |ii|| | 3 |
| Nearside Headlamp insecure |4.1.1 |c|| | 3 |
| Nearside Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 3 |
| Front Exhaust system not adequately supported |7.1.1| | 3 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
| Offside Rear Braking system leaking brake caliper |3.6.A.1| | 3 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Position lamp not working |4.2.1 |a|| | 3 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired |5.3.6 |a| |i|| | 3 |
| Nearside Headlamp aim headlamp not in good working order adversely affecting beam image |1.2.4b| | 3 |
| Rear Exhaust has a major leak of exhaust gases joint |6.1.2 |a|| | 3 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Offside front parking brake recording little or no effort |3.7.B.6a| | 3 |
| Offside Rear Position lamp not working |4.2.1 |a|| | 3 |
| Nearside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 3 |
| Offside Rear Brake cable has restricted free movement |3.5.1k| | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 3 |
| Offside Front front brake recording little or no effort |3.7.B.5a| | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 3 |
| Offside Inner Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Subframe mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 3 |
| Offside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 3 |
| Offside Front Lower Anti-roll bar linkage fractured |2.4.G.1| | 3 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 3 |
| Offside Front Brake hose twisted |3.6.B.4c| | 3 |
| Nearside Rear Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 3 |
| Offside Rear Lower Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 3 |
| Offside Rear Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 3 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 3 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 3 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 3 |
| Offside Front Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 3 |
| Offside Front Upper Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Rear Exhaust silencer insecure (8.1.1 (b) (i)) | 3 |
| Offside Rear Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 3 |
| Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 3 |
| Rear Electrical wiring insecure |1.9.2a| | 3 |
| Exhaust catalytic converter obviously modified (8.2.1.1 (a)) | 3 |
| Nearside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 3 |
| Nearside Front front brake grabbing severely |3.7.A.2b| | 3 |
| Offside Outer Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Rear brake disc contaminated by brake fluid |3.5.1h| | 3 |
| Offside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 3 |
| Offside Inner Rear brake disc excessively pitted |3.5.1h| | 3 |
| Nearside Front Upper Suspension arm locating pin locking device missing |2.4.G.3b| | 3 |
| Rear Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 3 |
| Offside Rear Hydraulic brake calliper leaking and braking performance affected |1.1.16 |b| |ii|| | 3 |
| Front Service brake imbalanced across an axle (1.2.1 (b) (i)) | 3 |
| Offside Rear Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 3 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 3 |
| Nearside Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 3 |
| Front An item not tested |Manual| | 3 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 3 |
| Nearside Front Subframe mounting prescribed area is fractured |2.4.A.3| | 3 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded chassis leg holed |5.2.6| | 3 |
| Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 3 |
| Nearside Rear Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Nearside Rear Anti-roll bar ball joint excessively worn |5.3.4 |a| |i|| | 3 |
| Rear rear brake excessively fluctuating |3.7.B.3| | 3 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 3 |
| Central Rear Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 3 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 3 |
| Rear fog lamp switch inoperative |4.5.3 |a| |ii|| | 3 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 3 |
| Nearside Rear Suspension component mounting prescribed area is fractured |2.4.A.3| | 3 |
| Nearside Front Brake hose excessively twisted |1.1.12 |b| |ii|| | 3 |
| Nearside brake disc excessively pitted |3.5.1h| | 3 |
| Centre Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Offside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 3 |
| Offside Front Anti-roll bar ball joint likely to become detached |5.3.4 |a| |ii|| | 3 |
| Offside Front Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 3 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 3 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 3 |
| Offside Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Rear position lamp|s| incomplete |1.1.4a| | 3 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 3 |
| Offside Rear Shock absorber casing corroded externally so the unit does not function |2.7.2a| | 3 |
| Offside Rear Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 3 |
| Nearside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 3 |
| Offside Front Anti-roll bar insecurely attached |5.3.3 |a| |i|| | 3 |
| Centre Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 3 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 3 |
| Nearside Inner Rear Road wheel bead rim badly distorted |4.2.A.1a| | 3 |
| Rear Exhaust has a major leak of exhaust gases joint |7.1.2| | 3 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 3 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 3 |
| Nearside Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 3 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded (7.1.1 (a) (i)) | 3 |
| Nearside Front Steering locking device missing |2.2.C.1g| | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded arch |5.2.6| | 3 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 3 |
| Offside Front Direction indicator not working |4.4.1 |a| |ii|| | 3 |
| Front Headlamp not working on main beam |1.7.5a| | 3 |
| Offside Headlamp insecure |4.1.1 |c|| | 3 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 3 |
| Nearside Rear Brake pivot has restricted free movement |3.5.1k| | 3 |
| Nearside Passenger`s seat insecure |6.2.A.1| | 3 |
| Offside Side repeater insecure |1.4.A.2b| | 3 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Offside Rear Road wheel cracked |4.2.A.1a| | 3 |
| Offside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Nearside Rear Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 3 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 3 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 3 |
| Fluid leak harmful to the environment or a risk to other road users coolant |8.4.1 |a| |i|| | 3 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill/floor |5.2.6| | 3 |
| Nearside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Rear Brake pipe at imminent risk of failure or fracture (1.1.11 (a)) | 3 |
| Offside Rear Upper Coil spring fractured or broken |5.3.1 |b| |i|| | 3 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 3 |
| Offside Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 3 |
| Offside Brake pipe leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) | 3 |
| Offside Front Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 3 |
| Offside Position lamp not working |4.2.1 |a|| | 3 |
| Nearside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 3 |
| Offside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 3 |
| Offside Front Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 3 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 3 |
| Offside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 3 |
| Offside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 3 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 3 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 3 |
| Offside Front Brake hose connection leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 2 |
| Offside Rear Anti-roll bar inappropriately repaired |2.4.A.2| | 2 |
| Nearside Outer Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 2 |
| Nearside Body has a sharp edge caused by damage door mirror |6.1.C.1| | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor corroded (7.1.1 (a) (i)) | 2 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 2 |
| Nearside Inner Rear brake disc excessively pitted |3.5.1h| | 2 |
| Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 2 |
| Offside Front Seat belt anchorage prescribed area is fractured |5.2.6| | 2 |
| Offside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 2 |
| Brake lever has abnormal movement of levers indicating maladjustment |3.5.1f| | 2 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Front Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Windscreen wiper blade missing (3.4 (b) (ii)) | 2 |
| Steering wheel rim loose (2.2.1 (c) (i)) | 2 |
| Nearside Front Anti-roll bar ball joint excessively worn |5.3.4 |a| |i|| | 2 |
| Centre Exhaust mounting missing |7.1.1b| | 2 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 2 |
| Brake warning device not working correctly |3.3.D.3a| | 2 |
| Nearside Rear front parking brake recording little or no effort |3.7.B.6a| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis rail |2.4.A.3| | 2 |
| Electronic stability system warning lamp indicates a fault |3.4.1c| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 2 |
| Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Rear reflector not red in colour |1.5.1d| | 2 |
| Nearside Rear Upper Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Emissions not tested due to exhaust |7.3.A.1| | 2 |
| Nearside Front Anti-roll bar has excessive play in a ball joint drop link |2.4.G.2| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 2 |
| Headlamps matched pair are incorrectly positioned |1.7.3| | 2 |
| Nearside Front Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer cill |7.1.1 |a| |i|| | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer cill |7.1.1 |a| |i|| | 2 |
| Nearside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Nearside Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 2 |
| Offside Side repeater incomplete |1.5.A1b| | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS RAIL (5.3.6 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS RAIL (5.3.6 (a) (i)) | 2 |
| Offside Obligatory mirror does not provide a view to the rear |8.1.2b| | 2 |
| Offside Rear Anti-roll bar linkage severely distorted |2.4.G.1| | 2 |
| Emissions not tested engine over heating (8.2.1.2 (d)) | 2 |
| Offside Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 2 |
| Offside Front Front position lamp|s| has a product on the light source so it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 2 |
| Offside Obligatory mirror missing |8.1.1| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassie |2.4.A.3| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassie |2.4.A.3| | 2 |
| Offside Front Track rod end ball joint worn to the extent there is a serious risk of detachment |2.1.3 |b| |ii|| | 2 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill
|2.4.A.3| | 2 |
| Nearside Rear Tie bar/rod insecure |2.4.G.1| | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.57% (8.2.1.2 (b)) | 2 |
| Nearside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Rear Lower Anti-roll bar linkage insecure |2.4.G.1| | 2 |
| Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 2 |
| Nearside Front front parking |secondary| brake grabbing severely |3.7.B.6b| | 2 |
| Offside All position lamps not working |1.1.A.3b| | 2 |
| Offside Front Headlamp not in good working order |not working| |1.2.4a| | 2 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 2 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Offside Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 2 |
| Rear fog lamp switch inoperative (4.5.3 (a) (ii)) | 2 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 2 |
| Offside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 2 |
| Nearside Steering locking device missing |2.2.C.1g| | 2 |
| Fuel pipe leaking |7.2.3| | 2 |
| Offside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 2 |
| Offside Rear Suspension component mounting prescribed area is fractured |2.4.A.3| | 2 |
| Front Service brake excessively binding both sides (1.2.1 (f)) | 2 |
| Bootlid cannot be secured in the closed position |6.4.1| | 2 |
| Nearside Front Headlamp not in good working order |not working| |1.2.4a| | 2 |
| Offside Brake pipe inadequately supported |3.6.B.1| | 2 |
| Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 2 |
| Nearside Front Headlamp are incorrectly positioned (4.1.4 (a)) | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 2 |
| Offside Rear Brake relay lever has restricted free movement uable to spin wheel (1.1.15 (e)) | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 2 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 2 |
| Offside Front Brake pipe inadequately supported |3.6.B.1| | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 2 |
| Nearside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Rear fog lamp not working |1.3.2b| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 2 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Road wheel fixing missing (5.2.1 (a) (i)) | 2 |
| Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 2 |
| Offside Rear Body has a sharp edge caused by corrosion arch |6.1.C.1| | 2 |
| Offside Front Anti-roll bar attachment bracket/mounting cracked |2.4.G.1| | 2 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 2 |
| Front Brake lining|s| less than 1.5 mm thick |3.5.1g| | 2 |
| Nearside Front Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Rear Upper Coil spring fractured or broken |5.3.1 |b| |i|| | 2 |
| Nearside Front Anti-roll bar fractured |2.4.G.1| | 2 |
| Front Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 2 |
| Nearside Front Body has a projection caused by damage |6.1.C.1| | 2 |
| Offside Front Body has a projection caused by damage |6.1.C.1| | 2 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Rear Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 2 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Front Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/chassis (5.3.6 (a) (i)) | 2 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill (6.2.2 (d) (i)) | 2 |
| Offside Rear Hydraulic brake calliper leaking and braking performance affected (1.1.16 (b) (ii)) | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis leg |2.4.A.3| | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover missing |2.4.G.2| | 2 |
| Offside Front Lower Suspension arm ball joint dust cover missing |2.4.G.2| | 2 |
| Nearside Front Anti-roll bar linkage cracked |2.4.G.1| | 2 |
| Nearside Rear Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail |6.1.1 |c| |i|| | 2 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Nearside Seat belt webbing significantly weakened (7.1.2 (b) (ii)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie (5.3.6 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 2 |
| Nearside Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits co to high |8.2.1.2 |a|| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outter sill |5.2.6| | 2 |
| Emissions not tested over heating (8.2.1.2 (d)) | 2 |
| Front Service brake excessively binding |1.2.1 |f|| | 2 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 2 |
| Nearside Front Direction indicator missing (4.4.1 (a) (ii)) | 2 |
| Offside Front position lamp(s) not working (1.1.A.3b) | 2 |
| Rear fog lamp tell tale not working (1.3.1b) | 2 |
| Offside Front Anti-roll bar linkage synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 2 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 2 |
| Nearside Front Position lamp with a multiple light source more than 1/2 not functioning (4.2.1 (a) (ii)) | 2 |
| Nearside Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 2 |
| Front Horn not working |1.6.2a| | 2 |
| Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 2 |
| Nearside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Vehicle structure has a modification which adversely affects braking or steering |6.1.A.1| | 2 |
| Nearside Rear An item not tested |Manual| | 2 |
| Nearside Front Lower Anti-roll bar linkage fractured |2.4.G.1| | 2 |
| Steering column movement between the shaft and steering wheel |2.1.2b| | 2 |
| Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 2 |
| Front Front position lamp|s| incorrect colour |1.1.A.3e| | 2 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 2 |
| Central Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 2 |
| Nearside Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Vehicle Identification Number has more than one different number displayed |6.3.5.b| | 2 |
| Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 2 |
| Rear fog lamp obviously incorrectly positioned |1.3.2a| | 2 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid |1.1.16 |b| |i|| | 2 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 2 |
| Offside Outer Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Front Lower Macpherson strut pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Rear Battery insecure |1.9.1| | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
| Offside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 2 |
| Wheel nut|s| missing |4.2.A.1e| | 2 |
| Offside Rear Brake lever has restricted free movement (1.1.15 (e)) | 2 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 2 |
| Offside Seat belt buckle not functioning as intended (7.1.2 (d)) | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill corroded (7.1.1 (a) (i)) | 2 |
| Nearside Rear Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Front Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 2 |
| Rear Coil spring fractured or broken both (5.3.1 (b) (i)) | 2 |
| Nearside Direction indicator not working |1.4.A.2c| | 2 |
| Offside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 2 |
| Nearside Front Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 2 |
| Nearside Front Direction indicator does not face the front (4.4.3 (a)) | 2 |
| Front Body insecure and dangerous to other road users |6.1.B.1b| | 2 |
| Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4) | 2 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 2 |
| Front Position lamp not working Both (4.2.1 (a) (ii)) | 2 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 2 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 2 |
| Nearside Inner Rear brake disc excessively scored |3.5.1h| | 2 |
| Offside Inner Rear brake disc excessively scored |3.5.1h| | 2 |
| Offside Front Hydraulic brake calliper leaking and braking performance affected (1.1.16 (b) (ii)) | 2 |
| Power steering fluid reservoir empty (2.1.5 (b) (ii)) | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 2 |
| Offside Front Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 2 |
| Offside Direction indicator not working |4.4.1 |a| |ii|| | 2 |
| Offside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 2 |
| Nearside Front Brake hose connection leaking on an air braking system (1.1.12 (c) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg (5.3.6 (a) (ii)) | 2 |
| Offside Rear Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 2 |
| Rear Service brake effort inadequate at a wheel both sides (1.2.1 (a) (i)) | 2 |
| Offside Rear fog lamp missing (1.3.2a) | 2 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 2 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Nearside Front Position lamp not working side light (4.2.1 (a) (ii)) | 2 |
| Headlamp light source and lamp not compatible (4.1.4 (c)) | 2 |
| Nearside Side repeater has less than 50% of the light sources illuminating |1.4.A.2c| | 2 |
| Offside Side repeater has less than 50% of the light sources illuminating |1.4.A.2c| | 2 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 2 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill |5.3.6 |a| |ii|| | 2 |
| Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 2 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 2 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 2 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 2 |
| Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 2 |
| Parking brake lever ratchet mechanism is broken |3.1.5| | 2 |
| Nearside Rear Direction indicator not working |4.4.1 |a| |ii|| | 2 |
| Nearside Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Power steering ram leaking (2.1.5 (a)) | 2 |
| Nearside Rear Macpherson strut insecure and impairing directional stability (5.3.3 (a) (ii)) | 2 |
| Nearside Front Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 2 |
| All position lamps adversely affected by the operation of another lamp (4.2.3 (c)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 2 |
| Offside Front Subframe mounting prescribed area is severely distorted |2.4.A.3| | 2 |
| Offside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside front brake binding (3.7.B.1) | 2 |
| Nearside Front position lamp(s) not working (1.1.A.3b) | 2 |
| Offside Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 2 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 2 |
| Headlamp not working on main beam both (4.1.1 (a) (ii)) | 2 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 2 |
| Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 2 |
| Nearside Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 2 |
| Offside Rear Brake hose excessively twisted (1.1.12 (b) (ii)) | 2 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 2 |
| Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill |5.3.6 |a| |i|| | 2 |
| Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 2 |
| Nearside Front Seat belt anchorage loose (7.1.1 (b)) | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 2 |
| Offside Front Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 2 |
| Offside Front Body panel insecure wing (6.2.1 (a) (i)) | 2 |
| Nearside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan (7.1.1 (a) (i)) | 2 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 2 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 2 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 2 |
| Nearside Front Upper Front suspension locking device missing |2.5.A.4| | 2 |
| Fuel tank leaking |7.2.3| | 2 |
| Offside Rear Anti-roll bar missing |2.4.G.1| | 2 |
| Offside Outer Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 2 |
| Offside Front Service brake grabbing severely (1.2.1 (c)) | 2 |
| Offside Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 2 |
| Nearside Front Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner wing where anti roll bar bolts on (5.3.6 (a) (i)) | 2 |
| Nearside Front Upper Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Nearside Rear Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Offside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 2 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 2 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
| Offside Front Brake lining|s| less than 1.5 mm thick |3.5.1g| | 2 |
| Nearside Parking |secondary brake| on a single line braking system has inadequate effort at a wheel |1.3.1 |a| |i|| | 2 |
| Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Emissions unable to be completed due to exhaust leak (8.2.1.2 (d)) | 2 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded SILL |5.2.6| | 2 |
| Brake reservoir fluid level decreases after several pedal applications |3.3.C.1| | 2 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bearing |2.4.G.2| | 2 |
| Nearside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis (6.2.2 (d) (i)) | 2 |
| Nearside Rear Fuel cap/sealing device missing (6.1.3 (b) (i)) | 2 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill holed |5.2.6| | 2 |
| Offside Headlamp aim beam image kick up to the offside |1.6.B1| | 2 |
| Offside Front coil spring corroded so that its cross sectional area is reduced and seriously weakened |2.4.C.1b| | 2 |
| Nearside Front Anti-roll bar insecure and impairing directional stability |5.3.3 |a| |ii|| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis |2.4.A.3| | 2 |
| Rear Brake lever has insufficient reserve travel |1.1.2 |a|| | 2 |
| Nearside Front Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 2 |
| Brake lever has insufficient reserve travel parking brake (1.1.2 (a)) | 2 |
| Headlamp excessively deteriorated so that the light output is severely reduced both |1.7.5a| | 2 |
| Offside Rear Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 2 |
| Nearside Rear position lamp|s| insecure |1.1.A.3a| | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Nearside Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 2 |
| Front Headlamp adversely affected by the operation of another lamp |1.7.5c| | 2 |
| Front Lower Power steering pipe|s| or hose|s| leaking |2.3.3b| | 2 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 2 |
| Nearside Rear Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 2 |
| Centre Braking system leaking |3.6.A.1| | 2 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wing |2.4.A.3| | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch |6.1.B.2| | 2 |
| Steering wheel has movement relative to the column indicating looseness |2.2.1 |a| |i|| | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded under sill |2.4.A.3| | 2 |
| Offside Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 2 |
| Offside Front Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| rear brake juddering severely |3.7.A.5b| | 2 |
| Nearside Rear Floor excessively deteriorated (6.2.4 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 2 |
| Seat belt anchorage prescribed area is excessively corroded nearside outer sill |5.2.6| | 2 |
| Offside Front Anti-roll bar linkage insecure broken |2.4.G.1| | 2 |
| Front Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WING (5.3.6 (a) (i)) | 2 |
| Nearside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing (6.2.2 (d) (i)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded OUTER SILL |5.2.6| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 2 |
| Emissions not tested exhaust leak |7.3.A.1| | 2 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 2 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Inner Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Rear Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill panel |5.2.6| | 2 |
| Nearside Front Tie bar/rod insecure |2.4.G.1| | 2 |
| Offside Front Upper Anti-roll bar linkage missing |2.4.G.1| | 2 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Front Upper Suspension arm locating pin locking device missing |2.4.G.3b| | 2 |
| Nearside Front Windscreen wiper blade missing |8.2.2| | 2 |
| Nearside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 2 |
| Rear Emissions not tested |7.0| | 2 |
| Windscreen in an unacceptable condition (3.2 (c) (i)) | 2 |
| Nearside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Rear Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 2 |
| Nearside Front Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 2 |
| Rear Brake disc contaminated (1.1.14 (b)) | 2 |
| Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 2 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 2 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 2 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill |6.2.2 |d| |i|| | 2 |
| Headlamp aim beam image obviously incorrect both sides |1.8.A.1b| | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced INNER SILL / FLOOR (7.1.1 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired chassis (5.3.6 (a) (i)) | 2 |
| Offside Drivers airbag missing (7.1.5 (a)) | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded chassis |5.2.6| | 2 |
| Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 2 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded Floor pan |5.2.6| | 2 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 2 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 2 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 2 |
| Nearside Front Vehicle structure is fractured and structural rigidity is significantly reduced |6.1.1 |a| |i|| | 2 |
| Offside Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 2 |
| Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 2 |
| Nearside Front Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Offside Side repeater missing |1.4.A.2b| | 2 |
| Offside Front Steering rack gaiter insecure |2.2.D.2d| | 2 |
| Offside Front Shock absorber casing corroded externally so the unit does not function |2.7.2a| | 2 |
| Front Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 2 |
| Nearside Front Upper Anti-roll bar linkage insecure |2.4.G.1| | 2 |
| Offside Front Anti-roll bar rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Rear Service brake excessively fluctuating |1.2.1 |e|| | 2 |
| Offside Front Braking system leaking caliper |3.6.A.1| | 2 |
| Stop lamp|s| all not working |4.3.1 |a| |iii|| | 2 |
| Headlamp light intensity severely reduced both |4.1.4 |a|| | 2 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 2 |
| Fuel cap/sealing device mounting flange/sealing method defective |7.2.4c| | 2 |
| Rear Exhaust has a major leak of exhaust gases at joint (6.1.2 (a)) | 2 |
| Emissions not tested due to exhaust leak (8.2.1.2 (d)) | 2 |
| Steering rack has excessive free play detected at the steering wheel (steering rack fitted) (2.3 (a) (i)) | 2 |
| Offside Braking system leaking front to rear brake pipe |3.6.A.1| | 2 |
| Offside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front brake caliper securing device loose |3.5.1j| | 2 |
| Rear Lower Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner wing |6.1.1 |c| |ii|| | 2 |
| Offside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Rear Brake disc contaminated (1.1.14 (b)) | 2 |
| Offside front brake grabbing severely |3.7.A.2b| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 2 |
| Offside Rear Road wheel fixing missing |5.2.1 |a| |i|| | 2 |
| Offside Front Inner Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 2 |
| Stop lamp not working high level |1.2.1b| | 2 |
| Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 2 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 2 |
| Rear Exhaust mounting missing |7.1.1b| | 2 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch |6.1.1 |c| |i|| | 2 |
| brake disc excessively scored |3.5.1h| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded under sill |5.2.6| | 2 |
| Offside Front Anti-roll bar linkage likely to become detached (5.3.3 (a) (ii)) | 2 |
| Nearside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Position lamp not working side (4.2.1 (a) (ii)) | 2 |
| Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch / chassis |2.4.A.3| | 2 |
| Central Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside rear parking |secondary| brake grabbing severely |3.7.B.6b| | 2 |
| Offside Front Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Obligatory mirror seriously deteriorated, affecting the rear view |8.1.2a| | 2 |
| Nearside Front Side repeater insecure |1.4.A.2b| | 2 |
| Offside Rear Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 2 |
| Offside Front Direction indicators not working |1.4.A.2c| | 2 |
| Nearside Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 2 |
| Rear Fuel tank leaking |7.2.3| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting (5.3.6 (a) (i)) | 2 |
| Nearside Rear Anti-roll bar insecure |2.4.G.1| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 2 |
| Rear brake excessively fluctuating | 2 |
| Offside Outer Rear Suspension component mounting prescribed area is fractured |2.4.A.3| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 2 |
| Front Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 2 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 2 |
| Nearside Rear Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch (7.1.1 (a) (i)) | 2 |
| Nearside Rear Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside front brake grabbing severely |3.7.A.2b| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill to floor |5.2.6| | 2 |
| Nearside Rear Tie bar/rod attachment bracket/mounting bolt missing |2.4.G.1| | 2 |
| Offside Rear Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mount (5.3.6 (a) (i)) | 2 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Nearside Front coil spring cracked |2.4.C.1a| | 2 |
| Inner Stop lamp not working |1.2.1b| | 2 |
| Offside Front Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 2 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded arch |2.4.A.3| | 2 |
| Offside Front Position lamp not working side light |4.2.1 |a|| | 2 |
| Offside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mount |5.3.6 |a| |i|| | 2 |
| Offside Rear Stop lamp emits other than a steady red light |1.2.1e| | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 2 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch |5.2.6| | 2 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wing (6.1.1 (c) (i)) | 2 |
| Emissions not tested |7.4.B.1| | 2 |
| Nearside Front Brake hose kinked |3.6.B.4b| | 2 |
| Offside Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
| Central Exhaust system insecure (6.1.2 (a)) | 2 |
| Offside Rear Anti-roll bar linkage cracked |2.4.G.1| | 2 |
| Nearside Rear Brake cable has restricted free movement |3.5.1k| | 2 |
| Offside Rear Service brake lagging in operation (1.2.1 (d)) | 2 |
| Nearside Front Body has a sharp edge caused by corrosion wing |6.1.C.1| | 2 |
| Nearside Outer Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Brake pedal anti-slip provision worn smooth (1.1.2 (c)) | 2 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 2 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 2 |
| Nearside Rear Anti-roll bar locating pin insecure |2.4.G.3a| | 2 |
| Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 2 |
| Offside Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 2 |
| Nearside Front Windscreen wiper not working |3.4 |a|| | 2 |
| Offside Rear Sub-frame attachment bracket/mounting insecure (5.3.3 (a) (i)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 2 |
| Nearside Rear Service brake excessively binding rear n/s brake binding (1.2.1 (f)) | 2 |
| Front Undertray likely to become detached (6.2.1 (a) (ii)) | 2 |
| Front Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 2 |
| Offside Front Brake hose excessively damaged |1.1.12 |b| |ii|| | 2 |
| Nearside Front Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 2 |
| Offside Rear Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded x2 |2.4.A.3| | 2 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bearing |2.4.G.2| | 2 |
| Emissions not tested Due to exhaust leak (8.2.1.2 (d)) | 2 |
| Nearside Front Lower Suspension arm corroded and seriously weakened shock mount (5.3.3 (b) (i)) | 2 |
| Offside Front Lower Shock absorbers insecurely attached (5.3.2 (a) (i)) | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch (6.2.2 (d) (i)) | 2 |
| Offside Outer Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Stop lamp excessively deteriorated so that it is not visible from a reasonable distance |1.2.1d| | 2 |
| Offside Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 2 |
| Offside Front Headlamp aim headlamp not in good working order adversely affecting beam image |1.2.4b| | 2 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Front Tie bar/rod cracked |2.4.G.1| | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 2 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 2 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 2 |
| Nearside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Centre Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front Drivers seat fore and aft adjustment mechanism not functioning as intended. (6.2.5 (b) (i)) | 2 |
| Nearside Front Headlamp incorrect colour (4.1.4 (a)) | 2 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill area (5.3.6 (a) (i)) | 2 |
| Power steering component|s| leaking rack |2.3.3b| | 2 |
| Offside Upper Front suspension locking device missing |2.5.A.4| | 2 |
| Offside Steering locking device missing |2.2.C.1g| | 2 |
| Nearside Rear Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Offside Front Outer Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 2 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Offside Front Lower Seat belt anchorage prescribed area is fractured |5.2.6| | 2 |
| Offside Front Steering locking device missing |2.2.C.1g| | 2 |
| Offside Front front brakes release unevenly |3.7.B.4| | 2 |
| Offside Front Road wheel fixing missing |5.2.1 |a| |i|| | 2 |
| Nearside Front Upper Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Offside Front Upper Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Nearside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Side repeater missing |4.4.1 |a| |ii|| | 2 |
| Offside Side repeater missing |4.4.1 |a| |ii|| | 2 |
| Nearside Headlamps matched pair are incorrectly positioned |1.7.3| | 2 |
| Exhaust has a major leak of exhaust gases centre too rear joint (6.1.2 (a)) | 2 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 2 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch |6.1.B.2| | 2 |
| Nearside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen |3.5 |a|| | 2 |
| Offside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill |5.3.6 |a| |ii|| | 2 |
| Rear Service brake excessively fluctuating both |1.2.1 |e|| | 2 |
| Nearside Seat belt locking mechanism does not secure or release |5.2.5a| | 2 |
| Offside Rear Upper coil spring fractured |2.4.C.1a| | 2 |
| Fuel system component insecure |7.2.1| | 2 |
| Offside Front Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 2 |
| Nearside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 2 |
| Rear Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 2 |
| Offside Rear Wheel nut|s| loose |4.2.A.1e| | 2 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 2 |
| Offside Front Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 2 |
| Nearside Front Service brake lagging in operation |1.2.1 |d|| | 2 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 2 |
| Nearside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 2 |
| Exhaust silencer insecure |8.1.1 |b| |i|| | 2 |
| Offside Front Front suspension locking device missing top joint aplit pin missing from nut |2.5.A.4| | 2 |
| Exhaust has a major leak of exhaust gases rear to mid box joint |7.1.2| | 2 |
| Nearside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 2 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
| Nearside Front Statutory seat belt missing |5.1.1| | 2 |
| Offside Front Upper Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Nearside Headlamp aim unable to be tested (4.1.2 (b)) | 2 |
| Offside Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 2 |
| Nearside Ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Rear Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 2 |
| Nearside Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill |5.3.6 |a| |i|| | 2 |
| Offside Front Anti-roll bar severely distorted |2.4.G.1| | 2 |
| Rear rear brakes release unevenly |3.7.B.4| | 2 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 2 |
| Headlamp incorrect colour |1.7.5b| | 2 |
| Offside Rear Hydraulic fluid leaking excessively (8.4.1 (a) (i)) | 2 |
| Stop lamp not working all |1.2.1b| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassi |2.4.A.3| | 2 |
| Nearside Outer Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed (7.1.1 (a) (i)) | 2 |
| Nearside Front passenger door cannot be opened from inside the vehicle |6.2.3 |a|| | 2 |
| Nearside Front passenger door cannot be opened from outside the vehicle |6.2.3 |a|| | 2 |
| Nearside Front Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 2 |
| Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 2 |
| Central Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 2 |
| Offside Front Road wheel badly damaged |4.2.A.1a| | 2 |
| Central Stop lamp(s) not working high level (4.3.1 (a) (ii)) | 2 |
| Rear Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 2 |
| Offside Rear Valve stem seriously damaged |5.2.3 |j|| | 2 |
| Steering wheel locking device insecure |2.1.6| | 2 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bearing |2.4.G.2| | 2 |
| Central Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill |7.1.1 |a| |i|| | 2 |
| Nearside Rear Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
| Offside Front Anti-roll bar linkage synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Offside Headlamp aim beam image too far to the left |1.6.B4| | 2 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wing (5.3.6 (a) (i)) | 2 |
| Nearside Front Road wheel fixing missing |5.2.1 |a| |i|| | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 2 |
| Power steering malfunctioning |2.1.5 |a|| | 2 |
| Offside Front Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 2 |
| Offside Front Headlamp lens seriously defective |4.1.1 |b| |ii|| | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 2 |
| Nearside Front Lower Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i)) | 2 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill |6.2.2 |d| |i|| | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 2 |
| Offside Front Power steering component|s| leaking |2.3.3b| | 2 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 2 |
| Offside Front Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 2 |
| Exhaust has a major leak of exhaust gases back box |7.1.2| | 2 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Offside Seat belt locking mechanism does not secure or release |5.2.5a| | 2 |
| Power steering pump leaking (2.1.5 (a)) | 2 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Nearside Rear front brake recording little or no effort |3.7.B.5a| | 2 |
| Nearside Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 2 |
| Front Brake pipe leaking on a hydraulic braking system to rear (1.1.11 (b) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 2 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill |6.2.2 |d| |i|| | 2 |
| Centre Front Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Offside Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 2 |
| Nearside Outer Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Brake pipe at imminent risk of failure or fracture |1.1.11 |a|| | 2 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front front parking |secondary| brake grabbing severely |3.7.B.6b| | 2 |
| Offside Rear position lamp|s| insecure |1.1.A.3a| | 2 |
| Nearside Outer Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Nearside Anti-roll bar linkage fractured |2.4.G.1| | 2 |
| Nearside Front Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 2 |
| Offside Front Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Brake pipe leaking front to rear |3.6.A.1| | 2 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor panel |7.1.1 |a| |i|| | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill panel |5.3.6 |a| |i|| | 2 |
| Offside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 2 |
| Offside Rear Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 2 |
| Rear coil spring broken both |2.4.C.1a| | 2 |
| Offside Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Front Anti-roll bar has excessive play in a pin/bearing |2.4.G.2| | 2 |
| Nearside Headlamp extinguishes when tapped lightly by hand |1.2.4c| | 2 |
| Nearside Rear Road wheel fixing missing |5.2.1 |a| |i|| | 2 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Offside Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 2 |
| Offside Rear Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 2 |
| Nearside Front Anti-roll bar ball joint likely to become detached |5.3.4 |a| |ii|| | 2 |
| Offside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill area |5.2.6| | 2 |
| Offside Front Upper Front suspension locking device missing ball joint split pin |2.5.A.4| | 2 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar |2.4.A.3| | 2 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 2 |
| Offside Front Torsion bar insecure at an end fixing |2.4.E.2| | 2 |
| Offside Front Fluid suspension unit leaking |2.4.D.2| | 2 |
| Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 2 |
| Rear Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 2 |
| front brake recording little or no effort both |3.7.B.5a| | 2 |
| Nearside Front Windscreen wiper blade missing (3.4 (b) (ii)) | 2 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 2 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 2 |
| Rear Anti-roll bar corroded and seriously weakened |2.4.G.1| | 2 |
| Rear Exhaust has a major leak of exhaust gases silencer joint |7.1.2| | 2 |
| Brake fluid warning lamp inoperative |3.6.G.2| | 2 |
| Speedometer cannot be illuminated. |6.7.3| | 2 |
| Nearside Body has a projection caused by corrosion |6.1.C.1| | 2 |
| Offside Rear Body panel corroded and likely to cause injury |6.2.1 |a| |i|| | 2 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 2 |
| Power steering component leaking rack (2.1.5 (a)) | 2 |
| Offside Anti-roll bar linkage insecure |2.4.G.1| | 2 |
| Central Rear Upper Stop lamp not working |1.2.1b| | 2 |
| Offside Outer Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 2 |
| Nearside Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Nearside Rear Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 2 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 2 |
| Offside Outer Rear brake disc excessively pitted |3.5.1h| | 2 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
| Offside Front Brake pipe inadequately clipped |3.6.B.1| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded arch |5.2.6| | 2 |
| Nearside Rear Bonded suspension unit bonding failed and part of unit is likely to become displaced |2.4.F.2| | 2 |
| Rear Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 2 |
| Nearside Rear Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.4.G.4e| | 2 |
| Brake lever has restricted free movement |3.5.1k| | 2 |
| Offside Rear Rear position lamp|s| incorrect colour |1.1.A.3e| | 2 |
| Nearside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 2 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill (7.1.1 (a) (i)) | 2 |
| Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Offside Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 2 |
| Offside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 2 |
| Nearside Rear Sub-frame attachment bracket/mounting insecure |2.4.G.1| | 2 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor to sill area |6.1.B.2| | 2 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 2 |
| Nearside Front Shock absorbers insecurely attached |5.3.2 |a| |i|| | 2 |
| Nearside Front Headlamp insecure |4.1.1 |c|| | 2 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Nearside Front Front suspension locking device missing |2.5.A.4| | 2 |
| Nearside Front Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside Outer Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 2 |
| Front Exhaust catalytic converter missing where one was fitted as standard |8.2.1.1 |a|| | 2 |
| Nearside Rear Hydraulic brake calliper leaking and braking performance affected (1.1.16 (b) (ii)) | 2 |
| Electrical wiring inadequately supported |1.9.2a| | 2 |
| Nearside Front Steering rack gaiter insecure |2.2.D.2d| | 2 |
| Central Exhaust system not adequately supported |7.1.1| | 2 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre |6.1.B.2| | 2 |
| Rear Exhaust has a major leak of exhaust gases silencer (6.1.2 (a)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill back (7.1.1 (a) (i)) | 2 |
| Offside Front position lamp|s| not working side |1.1.A.3b| | 2 |
| Nearside Rear Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 2 |
| Nearside Headlamp aim beam image too far to the right |1.6.B4| | 2 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 2 |
| Nearside Front Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 2 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 2 |
| Nearside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front Headlamp aim not tested |4.1.2 |b|| | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill |6.2.2 |d| |i|| | 2 |
| Nearside Front Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 2 |
| Offside Rear Brake pipe at imminent risk of failure or fracture (1.1.11 (a)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch |5.3.6 |a| |i|| | 2 |
| Offside Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Brake performance not tested brake pipe burst (1.2.1 (g)) | 2 |
| Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Nearside Front Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 2 |
| Offside Front Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 2 |
| Offside Rear Braking system leaking Brake caliper |3.6.A.1| | 2 |
| Fuel hose leaking |7.2.3| | 2 |
| Offside Rear Tie bar/rod fractured |2.4.G.1| | 2 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer sill |5.2.6| | 2 |
| Centre Rear Exhaust system not adequately supported |7.1.1| | 2 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch |5.3.6 |a| |i|| | 2 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 2 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 2 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 2 |
| Rear Anti-roll bar linkage fractured |2.4.G.1| | 2 |
| Offside Rear Anti-roll bar attachment bracket/mounting insecure (5.3.3 (a) (i)) | 2 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 2 |
| Offside Rear Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis leg (6.2.2 (d) (i)) | 2 |
| Horn emits two or more alternating tones |1.6.2d| | 2 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 2 |
| Offside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 2 |
| Offside Front Headlamp light source and lamp not compatible LED (4.1.4 (c)) | 2 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 2 |
| Nearside Headlamp aim not tested |4.1.2 |b|| | 2 |
| Offside Front All position lamps not working |4.2.1 |a|| | 2 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 2 |
| Offside Front Brake pipe at imminent risk of failure or fracture (1.1.11 (a)) | 2 |
| Offside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 2 |
| Offside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 2 |
| Nearside Front Stop lamp not working |1.2.1b| | 2 |
| Nearside Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 2 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 2 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
| Exhaust emits excessive dense blue smoke during acceleration |8.2.1.2 |g|| | 2 |
| Rear Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch |5.2.6| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 2 |
| Offside Rear Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Front Sub-frame corroded and seriously weakened |2.4.G.1| | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills |5.3.6 |a| |i|| | 2 |
| Rear fog lamp switch insecure |1.3.1a| | 2 |
| Nearside Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill |6.1.1 |c| |i|| | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill
|2.4.A.3| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan (5.3.6 (a) (i)) | 2 |
| Offside Front Upper Anti-roll bar insecure |2.4.G.1| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill/floor |5.2.6| | 2 |
| Centre Rear fog lamp missing |1.3.2a| | 2 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Offside Obligatory mirror insecure |8.1.1| | 2 |
| Engine MIL inoperative or indicates a malfunction |8.2.2.2 |g|| | 2 |
| Rear Exhaust has a major leak of exhaust gases box |7.1.2| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 2 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor |6.1.1 |c| |i|| | 2 |
| Offside Front Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 2 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded ROLL BAR MOUNTING |2.4.A.3| | 1 |
| Horn not working |1.6.2a| | 1 |
| Rear parking brake recording little or no effort | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Nearside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Emissions not tested |7.0| | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Dipswitch operation does not extinguish all main beam headlamps leaving at least one pair of dipped beam headlamps |1.7.4b| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Rear fog lamp switch faulty |1.3.1a| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Windscreen washer not working | 1 |
| Emissions not tested due to over heating |7.3.A.1| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 1 |
| Offside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear coil spring broken |2.4.C.1a| | 1 |
| Anti-lock braking system warning lamp does not illuminate |3.4.1b| | 1 |
| Offside Rear Braking system leaking |3.6.A.1| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Centre Stop lamp not working |1.2.1b| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear coil spring incomplete |2.4.C.1a| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Direction indicators not working |1.4.A.2c| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Rear brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Headlamp aim not tested |1.8.A.1c| | 1 |
| Nearside Rear Braking system leaking brake caliper |3.6.A.1| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Headlamp insecure (4.1.1 (c)) | 1 |
| Offside Headlamp aim not tested due to headlamp insecurity (4.1.2 (b)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Steering rack gaiter split (2.2.D.2d) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Offside front brake binding (3.7.B.1) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect kick up to right hand side ( lhd headlamp) (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect KICK UP TO RIGHT ( LHD HEADLAMP (4.1.2 (c)) | 1 |
| Offside Front Brake pipe leaking on a hydraulic braking system TO FLEXI (1.1.11 (b) (ii)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced nsr inner sill corroded (7.1.1 (a) (i)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Offside Front Hydraulic brake calliper insecurely mounted bolt loose (1.1.16 (c) (i)) | 1 |
| Suspension arm has an unsafe modification osr top check nut loose (5.3.3 (c) (i)) | 1 |
| Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor pan / bulkhead (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch / sill closing panel (7.1.1 (a) (i)) | 1 |
| Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sil (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sil (6.2.2 (d) (i)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer arch (7.1.1 (a) (i)) | 1 |
| Parking brake lever ratchet not holding correctly (1.1.6 (a)) | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Nearside Rear Shock absorbers has a serious fluid leak | 1 |
| Front Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Fuel hose leaking Braided hose leaking at metal pipe joint. (6.1.3 (b) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed (marked.) (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed (marked.) (7.1.1 (a) (i)) | 1 |
| Nearside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Nearside Front Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Offside Front Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 1 |
| Parking brake lever inoperative Cable snapped on brake test (1.1.6 (d)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded through (7.1.1 (a) (i)) | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
| Emissions unable to be completed vehicle overheating (8.2.1.2 (d)) | 1 |
| Brake performance unable to be tested overheating (1.2.1 (g)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired inner sill not continuously welded repair plate (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill/floor |5.2.6| | 1 |
| Offside Rear Brake pipe leaking on an air braking system |1.1.11 |b| |i|| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill, hole |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill, hole |6.1.B.2| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion arch |6.1.C.1| | 1 |
| Offside Steering system fouling |2.2.D.2a| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill panel (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded floor - sill holed |5.2.6| | 1 |
| Offside Front Lower front brake binding |3.7.B.1| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded outer |5.2.6| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded outer |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength roll bar mount |5.3.6 |a| |i|| | 1 |
| Central Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Anti-roll bar attachment bracket inappropriately repaired |2.4.A.2| | 1 |
| Front Power steering ram|s| leaking from a failed component |2.3.3b| | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end ,inner sill, holed and corroded ( outer sill corroded not holed) (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sillend ,outer sill, upper wheel arch holed and corroded (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
| Prop shaft joint excessively worn rearmost (6.1.7 (c) (i)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint likely to become detached broken (5.3.4 (a) (ii)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded and holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Emissions not tested due over heating/ head gasket fault (8.2.1.2 (d)) | 1 |
| Nearside Power steering pipe/hose leaking hose or pump (2.1.5 (a)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Front Exhaust system insecure clamp at gear box corroded (6.1.2 (a)) | 1 |
| Battery insecure and likely to cause a short circuit and terminals slack (4.13 (a) (ii)) | 1 |
| Offside Seat belt insecurely fixed to the seat |5.2.1a| | 1 |
| Centre Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Road wheel more than one fixing loose Nearside and offside front (5.2.1 (a) (ii)) | 1 |
| Road wheel more than one fixing loose Nearside and offside rear (5.2.1 (a) (ii)) | 1 |
| Offside Front Suspension arm ball joint likely to become detached Bolt loose (5.3.4 (a) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded sill/inner sill |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded sill/inner sill |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded floor[behind wheel] |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded floor [behind wheel] |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill/inner sill |2.4.A.3| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/n/s inner arch |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/inner sill/chassis |5.3.6 |a| |i|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both sides rear outer boot floor (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/front outrigger (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing pannel |6.1.B.2| | 1 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing pannel |6.1.B.2| | 1 |
| Exhaust shield missing where fitted as original equipment creating a risk of fire (6.1.3 (e)) | 1 |
| Nearside Front Suspension arm severely distorted |2.4.G.1| | 1 |
| Nearside Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 1 |
| Offside Front Obligatory mirror missing |8.1.1| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill
|5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases centre clamp (6.1.2 (a)) | 1 |
| Emissions not tested vehicle overheating (8.2.1.2 (d)) | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor to sill front to rear |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor to sill |6.1.B.2| | 1 |
| Offside Front Suspension arm has an unsafe modification arm has been welded (5.3.3 (c) (i)) | 1 |
| Emissions not tested due to engine coolant fan not working.engine getting hot |8.2.1.2 |d|| | 1 |
| Offside Rear Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Outer Steering locking device missing track rod end slit pin missing (2.1.3 (d)) | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis in wheel arch. |6.1.B.2| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed and corroded. |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Chassis in front of wishbone mounting |6.1.1 |c| |ii|| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened body mount (5.3.3 (b) (i)) | 1 |
| Exhaust system not adequately supported rear mount broken |7.1.1| | 1 |
| Offside Front Anti-roll bar linkage damaged and seriously weakened DISCONNECTED AT BALL JOINT |2.4.G.1| | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis leg (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill area (6.2.2 (d) (i)) | 1 |
| Nearside Front Hydraulic brake calliper damaged and braking performance affected siezed (1.1.16 (a) (ii)) | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits Co 0.33 |8.2.1.2 |b|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre sill underneath (7.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure is fractured and structural rigidity is significantly reduced chassis leg (6.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected within 30cm of roll bar and front crossmember mountings (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected within 30cm of roll bar and front crossmember mountings (5.3.6 (a) (ii)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie leg near top suspension arm (5.3.6 (a) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced OFFSIDE INNER SILL AND FLOOR AREA FRONT TO REAR (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced OUTER SILL (6.1.1 (c) (i)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits co0.594 max0.300 (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits 0.594 (8.2.1.2 (a)) | 1 |
| Offside Rear Tie bar/rod ball joint dust cover missing |2.4.G.2| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
| Offside Inner Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front Brake disc significantly and obviously worn inner face badly corroded (1.1.14 (a) (i)) | 1 |
| Exhaust emissions carbon monoxide content excessive test aborted due to excessively high reading (8.2.1.2 (b)) | 1 |
| Power steering pump leaking from a failed joint |2.3.3b| | 1 |
| Offside Rear Parking brake inoperative on one side low (1.4.1 (a)) | 1 |
| Rear Exhaust system insecure three mountings split |6.1.2 |a|| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Front position lamp|s| not working flickering |1.1.A.3b| | 1 |
| Power steering pipe|s| or hose|s| leaking pipe corroded and leaking |2.3.3b| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear sill rusted (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner sill rusted (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner sill rusted (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced rear outer sill rusted (7.1.1 (a) (i)) | 1 |
| Offside Front Direction indicator missing (4.4.1 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced o/s/f top suspension mtg area (6.1.1 (c) (i)) | 1 |
| Nearside Rear Hydraulic fluid leaking excessively At brake caliper |8.4.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength At inner wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength At inner wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Offside Front Subframe mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Hydraulic brake calliper leaking and braking performance affected |1.1.16 |b| |ii|| | 1 |
| Nearside Front Front position lamp(s) not working (1.1.A.3b) | 1 |
| Offside Rear coil spring fractured (2.4.C.1a) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill area |6.1.1 |c| |i|| | 1 |
| Nearside Front Lower Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor panel (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced centre floor panel (6.1.1 (c) (i)) | 1 |
| Offside Front Headlamp not working on dipped beam tapped and worked (4.1.1 (a) (ii)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected (4.11 (a) (ii)) | 1 |
| Offside Front Brake hose excessively damaged fouling against wheel (1.1.12 (b) (ii)) | 1 |
| Emissions not tested no cat running rich (8.2.1.2 (d)) | 1 |
| Offside Front Lower Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush likely to become detached has become detached (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill inadequately repaired (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill / Wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill / Wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Road wheel fixing loose (5.2.1 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm insecurely attached Rear Bolt loose (5.3.3 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced rear end of sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rear end of sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front Vehicle structure has a modification which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Vehicle structure has a modification which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings OUTER SILL |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings CHASSIS LEG |6.1.B.2| | 1 |
| Front Exhaust has a major leak of exhaust gases manifold (6.1.2 (a)) | 1 |
| Offside Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Emissions not tested due to car overheating (8.2.1.2 (d)) | 1 |
| Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Offside Upper Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper front and rear of wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch area (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Body component corroded and likely to cause injury Above wheel arch (6.2.1 (a) (i)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Front crash bar (6.1.1 (c) (i)) | 1 |
| Offside Rear Upper Seat belt anchorage prescribed area strength or continuity significantly reduced inner wing (7.1.1 (a) (i)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.13 (8.2.1.2 (c)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength out rigger by subframe mount (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.48% (8.2.1.2 (b)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt split (2.1.3 (g) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i)) | 1 |
| Front Service brake excessively binding free off front brakes (1.2.1 (f)) | 1 |
| Nearside Front Lower Position lamp light intensity significantly reduced INTERMITTENT (4.2.3 (a) (ii)) | 1 |
| Offside Front Lower Position lamp light intensity significantly reduced INTERMITTENT (4.2.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg area 2 holes (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg area 3 holes (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area 2 holes (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area 3 holes (7.1.1 (a) (i)) | 1 |
| Suspension arm ball joint dust cover no longer prevents the ingress of dirt both sides (5.3.4 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced corroded outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength by upper suspension arm (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension rod insecurely attached outer (5.3.3 (a) (i)) | 1 |
| Central Rear Brake pipe likely to become detached or damaged (1.1.11 (d) (ii)) | 1 |
| Nearside Front Brake pipe likely to become detached or damaged RUBBING ON WISH BONE (1.1.11 (d) (ii)) | 1 |
| Offside Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 1 |
| Central Exhaust catalytic converter missing where one was fitted as standard (8.2.2.1 (a)) | 1 |
| Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Front Seat belt buckle missing (7.1.2 (d)) | 1 |
| Nearside Front Steering locking device missing Split pin (2.1.3 (d)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL AREA (5.3.6 (a) (i)) | 1 |
| Offside Side repeater missing (4.4.1 (a) (ii)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting multiple points (6.2.2 (d) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases centre exhaust join (6.1.2 (a)) | 1 |
| Emissions unable to be completed Due to exhaust gas leak and no catalytic convertor (8.2.1.2 (d)) | 1 |
| Nearside Front Upper Suspension arm attachment bracket/mounting missing (5.3.3 (a) (ii)) | 1 |
| Horn not working control missing (7.7 (a)) | 1 |
| Offside Rear Body component damaged and likely to cause injury bumper (6.2.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength under floor chassis leg area (5.3.6 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill/floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill at rear (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill at rear (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner wheel arch (7.1.1 (a) (i)) | 1 |
| Fuel system component leaking injector (6.1.3 (b) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor holed within 30cm of the lower arm mount (5.3.6 (a) (i)) | 1 |
| Offside Front Floor excessively deteriorated Floor Pan (6.2.4 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Brake performance unable to be tested due to leak (1.2.1 (g)) | 1 |
| Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel Both rear parking brakes do not work (1.3.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases From welds (6.1.2 (a)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt Upper and lower ball joint covers split (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt Upper and lower ball joint covers split (5.3.4 (b) (ii)) | 1 |
| Offside Front Outer Brake lining(s) missing Lining still present but no longer attached to the pad (1.1.13 (c)) | 1 |
| Offside Stop lamp|s| adversely affected by the operation of another lamp indicator |4.3.3 |b|| | 1 |
| Nearside Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Hydraulic brake cylinder operating mechanism has excessive travel (1.1.16 (e) (i)) | 1 |
| Nearside Front Wheel bearing rough when rotated also has play (5.1.3 (b) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits too high (8.2.1.2 (a)) | 1 |
| Nearside Front Hydraulic brake cylinder leaking hydraulic fluid |1.1.16 |b| |i|| | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid |1.1.16 |b| |i|| | 1 |
| Nearside Front Obligatory mirror insecure (3.3 (b) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel arch corroded within 30cm of seatbelt mounting (7.1.1 (a) (i)) | 1 |
| Offside Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill area (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor member |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Subframe Area (5.3.6 (a) (i)) | 1 |
| Nearside Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis above anto roll bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced in arch (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced in arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under sill /floor area (7.1.1 (a) (i)) | 1 |
| Nearside Outer Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Sill Corroded and Holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer Sill Corroded and Holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Headlamp incorrect colour (4.1.4 (a)) | 1 |
| Front Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced undersil |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced undersil |7.1.1 |a| |i|| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Track rod end ball joint has excessive play Both front (2.1.3 (b) (i)) | 1 |
| Offside Service brake indicates brake bind |3.7.D.2a| | 1 |
| Nearside Headlamp light intensity severely reduced main beam (4.1.4 (a)) | 1 |
| Emissions not tested due to coolant leak (8.2.1.2 (d)) | 1 |
| Nearside Front Headlamp light intensity severely reduced On main beam, light dim (4.1.4 (a)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Corroded under wheel arch within 30cm of shocker (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Corroded under wheel arch within 30cm of shocker (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn nut not tight allowing play (5.3.4 (a) (i)) | 1 |
| Offside Front Track rod end loose |2.2.B.1d| | 1 |
| Front Exhaust mounting missing |7.1.1b| | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction STICKERS IN SWEPT AREA... (3.1 (a) (ii)) | 1 |
| Nearside Front Body panel damaged and likely to cause injury WING... (6.2.1 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL PANEL... (7.1.1 (a) (i)) | 1 |
| Rear fog lamp obscured more than 50% |1.3.2c| | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt wish bone (5.3.4 (b) (ii)) | 1 |
| Suspension component ball joint dust cover no longer prevents the ingress of dirt both front top joints (5.3.4 (b) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases two centre joints (6.1.2 (a)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill working up to the inner wing as well. Marked in Yellow (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill and inner wheel arch |5.2.6| | 1 |
| Nearside Rear Upper Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Upper Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Side repeater not working |1.4.A.2c| | 1 |
| Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis on floor (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis on floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch corroded. marked with chalk. (7.1.1 (a) (i)) | 1 |
| Offside Front Front position lamp|s| flickers when tapped lightly by hand |1.1.4c| | 1 |
| Nearside Front Upper Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Upper Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis corroded (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill/wheel arch (6.2.2 (d) (i)) | 1 |
| Front Shock absorbers has negligible damping effect both fronts (5.3.2 (d)) | 1 |
| Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt both front (5.3.4 (b) (ii)) | 1 |
| Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt both fronts (2.1.3 (g) (ii)) | 1 |
| Nearside Side repeater incomplete |1.5.A1b| | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill door step (7.1.1 (a) (i)) | 1 |
| Rear Body component damaged and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Nearside Front Body has an unsafe modification (6.2.1 (d) (i)) | 1 |
| Offside Front Body has an unsafe modification (6.2.1 (d) (i)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting missing (5.3.3 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill and inner wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill and floor panel (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill and floor panel (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting missing Nut missing (5.3.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Nearside Front Side repeater incorrect colour (4.4.3 (a)) | 1 |
| Offside Front Side repeater incorrect colour (4.4.3 (a)) | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii)) | 1 |
| Stop lamp(s) adversely affected by the operation of another lamp when side light applied (4.3.3 (b)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced And outer sill (6.1.1 (c) (i)) | 1 |
| Offside Front Headlamp light intensity severely reduced dip and main beam (4.1.4 (a)) | 1 |
| Offside Rear Parking brake inoperative on one side is working slightly but not enough. ( n/s 146 o/s 38 effort (1.4.1 (a)) | 1 |
| Offside Rear Rear fog lamp light intensity significantly reduced showing white (4.5.4 (a)) | 1 |
| Rear Exhaust has a major leak of exhaust gases exhaust silencer (6.1.2 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced as marked (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
| Rear Position lamp not working both (4.2.1 (a) (ii)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak Exhaust flex blowing (8.2.2.1 (b)) | 1 |
| Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner And Outer Sills (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner And Outer Sills (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner And Outer Sills (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sills, Front & Rear (6.1.1 (c) (i)) | 1 |
| Front Vehicle structure is deformed and structural rigidity is significantly reduced Both Nearside & Offside, Chassis Legs (6.1.1 (a) (i)) | 1 |
| Offside Front Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases cat joint (6.1.2 (a)) | 1 |
| Front Vehicle structure modified such that it is likely to adversely affect braking or steering (6.1.1 (d) (ii)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill section (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced CHASSIS (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength FLOOR (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced CHASSIS (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER ARCH (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced CENTRE AND REAR FLOOR (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed exhaust leak at flange and rear box (8.2.1.2 (d)) | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded inner wing holed (1.1.21 (e) (i)) | 1 |
| Position lamp light intensity significantly reduced both front (4.2.3 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch /top mounting (7.1.1 (a) (i)) | 1 |
| Offside Integral body structure inadequately repaired such that structural rigidity is significantly reduced chassis leg holed and inadequate repair . (6.1.1 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure modified such that structural rigidity is significantly reduced inner wing has section removed within 30cm of top shocker suspension mounting. (6.1.1 (d) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (previous rep) (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg/floor (6.1.1 (c) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner side sill x2 places (6.1.1 (c) (i)) | 1 |
| Nearside Obligatory mirror does not provide a view to the rear (3.3 (c)) | 1 |
| Nearside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Nearside Suspension component mounting prescribed area fractured significantly reducing structural strength sill at rear (5.3.6 (a) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases flange (6.1.2 (a)) | 1 |
| Emissions unable to be completed due too extreme engine rattle when revving (8.2.1.2 (d)) | 1 |
| Offside Front Lower Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis (6.2.2 (d) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wheel arch / floor / inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wheel arch / floor / inner sill (6.1.1 (c) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure is fractured and structural rigidity is significantly reduced Chassis rail (6.1.1 (a) (i)) | 1 |
| Emissions unable to be completed Car over heating (8.2.1.2 (d)) | 1 |
| Rear Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front inner sill has a hole from corrosion. (5.3.6 (a) (i)) | 1 |
| Offside Service brake excessively binding (1.2.1 (f)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected under bonnet (4.11 (a) (ii)) | 1 |
| Nearside Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Nearside Front Lower Suspension arm insecure and impairing directional stability arm (5.3.3 (a) (ii)) | 1 |
| Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Lower sill excessively corroded. (7.1.1 (a) (i)) | 1 |
| Exhaust catalytic converter obviously defective (8.2.1.1 (a)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill to floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Steering locking device missing track rod end (2.1.3 (d)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced Both rear inner sills (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp not working on dipped beam operation affected by high beam operation (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect and too high (4.1.2 (c)) | 1 |
| Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Front Headlamp has a product on the light source so that the light output is severely reduced earth fault (4.1.4 (b)) | 1 |
| Central Front Steering rack gaiter missing or no longer prevents the ingress of dirt clip missing (2.1.3 (g) (ii)) | 1 |
| Nearside Front Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 1 |
| Rear Anti-roll bar linkage has excessive play in a ball joint Both Rear |2.4.G.2| | 1 |
| Rear Service brake effort inadequate at a wheel Nearside & Offside (1.2.1 (a) (i)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury wheel arch |6.2.1 |a| |i|| | 1 |
| Offside Rear Body panel corroded and likely to cause injury wheel arch |6.2.1 |a| |i|| | 1 |
| Nearside Rear Coil spring fractured or broken broken (5.3.1 (b) (i)) | 1 |
| Front Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect kick up to right hand side ( lhd headlamp) (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect KICK UP TO RIGHT ( LHD HEADLAMP (4.1.2 (c)) | 1 |
| Nearside Rear Brake pedal not releasing correctly and functionality of brakes affected (1.1.2 (b) (ii)) | 1 |
| Offside Rear Brake pedal not releasing correctly and functionality of brakes affected (1.1.2 (b) (ii)) | 1 |
| Emissions unable to be completed Due to overheating (8.2.1.2 (d)) | 1 |
| Brake fluid not visible (1.1.10 (d) (iii)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill holed (6.2.2 (d) (i)) | 1 |
| Steering box leaking to the extent that oil is dripping steering system |2.1.1 |e| |ii|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor/ chassis rail (7.1.1 (a) (i)) | 1 |
| Rear Fuel system component leaking |7.2.3| | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn Lower ball joint loose (5.3.4 (a) (i)) | 1 |
| Offside Drivers door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced end of sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar linkage fractured drop arm broken (5.3.3 (b) (ii)) | 1 |
| Windscreen in such a condition that visibility through swept area is seriously affected cracked windscreen in driers view (3.2 (c) (ii)) | 1 |
| Nearside Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Steering arm deformed to the extent that steering is affected Track arm (2.1.3 (c) (ii)) | 1 |
| Nearside Suspension component corroded and seriously weakened Sill end (5.3.3 (b) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits 0.697 (8.2.1.2 (a)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits 0.619% |8.2.1.2 |a|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor in two parts (6.1.1 (c) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases Union between pipe and cat (6.1.2 (a)) | 1 |
| Speedometer cannot be illuminated (7.8 (c) (ii)) | 1 |
| Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Offside Brake hose excessively twisted Rubbing on suspension arm (1.1.12 (b) (ii)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill panel (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch holed and corroded near (7.1.1 (a) (i)) | 1 |
| Emissions not tested due to vehicle overheated during test (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed near (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed near (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch holed near (7.1.1 (a) (i)) | 1 |
| Steering component mounting prescribed area is fractured |2.2.C.1h| | 1 |
| Nearside Front Headlamp aim beam image too far to the right |1.6.B4| | 1 |
| Electrical wiring insecure and connectors likely to become disconnected Battery terminal loose (4.11 (a) (ii)) | 1 |
| Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension arm ball joint likely to become detached bolt loose (5.3.4 (a) (ii)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill + inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced bottom of wing (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced bottom of wing (6.1.1 (c) (i)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected positive battery terminal loose (4.11 (a) (ii)) | 1 |
| Exhaust catalytic converter missing where one was fitted as standard supplied date of 1st use 01/03/1999 (8.2.1.1 (a)) | 1 |
| Front Headlamps matched pair are not the same colour |1.7.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill is severely corroded. (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outside of sill is severely corroded. (7.1.1 (a) (i)) | 1 |
| Front Body has an unsafe modification wheels catching arches (6.2.1 (d) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel corroded (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill panel corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch corroded (7.1.1 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength n/s & o/s inner sills (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis as marked (5.3.6 (a) (i)) | 1 |
| Nearside Direction indicator not working side repeter (4.4.1 (a) (ii)) | 1 |
| Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Rear Brake performance not tested stuck on |1.2.1 |g|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mount |5.3.6 |a| |i|| | 1 |
| Offside Front Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Rear Inner Anti-roll bar pin or bush excessively worn both sides (5.3.4 (a) (i)) | 1 |
| Nearside Front Inner Suspension arm insecurely attached (5.3.3 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Direction indicator not working front and rear (4.4.1 (a) (ii)) | 1 |
| Offside Hazard warning lamps inoperative front and rear not working (4.4.1 (e)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements no tell tail light (4.5.3 (a)) | 1 |
| Front Horn not working (7.7 (a)) | 1 |
| Offside Front Integral body structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Nearside Front Integral body structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Offside Rear fog lamp light intensity significantly reduced |4.5.4 |a|| | 1 |
| Central Front Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both nearside and offside chassis legs |5.3.6 |a| |i|| | 1 |
| Nearside Front Tie bar/rod attachment bracket/mounting cracked |2.4.G.1| | 1 |
| Rear Brake disc significantly and obviously worn corroded (1.1.14 (a) (i)) | 1 |
| Fluid leaking continuously posing a serious risk to road safety power steering fluid leaking badly (8.4.1 (a) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis rail (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced chassis rail (7.1.1 (a) (i)) | 1 |
| Nearside Front Track rod end modification unsafe (2.1.3 (f) (i)) | 1 |
| Offside Front Track rod end modification unsafe (2.1.3 (f) (i)) | 1 |
| Nearside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Battery leaking electrolyte |1.9.1| | 1 |
| Front Position lamp with a multiple light source more than 1/2 not functioning BOTH . (4.2.1 (a) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength BOOT AREA . (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced TO REAR , (7.1.1 (a) (i)) | 1 |
| Parking brake inoperative on one side not working on either side (1.4.1 (a)) | 1 |
| Nearside Rear Brake valve leaking brake caliper leaking (1.1.7 (d) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage fractured |5.3.3 |b| |ii|| | 1 |
| Rear Parking brake inoperative on one side both sides (1.4.1 (a)) | 1 |
| Nearside Front Steering component deformed SUB-FRAME STEERING RACK BRACKET DAMAGED (2.1.3 (c) (i)) | 1 |
| All position lamps not working (1.1.A.3b) | 1 |
| Rear fog lamp not working (1.3.2b) | 1 |
| Battery insecure (1.9.1) | 1 |
| Horn not working Intermittently (7.7 (a)) | 1 |
| Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt Both sides (5.3.4 (b) (ii)) | 1 |
| Nearside Front Steering rack gaiter split (2.2.D.2d) | 1 |
| Nearside Rear Shock absorber has a serious fluid leak (2.7.3) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Centre Exhaust system not adequately supported (7.1.1) | 1 |
| Horn not working (1.6.2a) | 1 |
| Front Direction indicator incorrect colour both sides (4.4.3 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced OSR outer sill (7.1.1 (a) (i)) | 1 |
| Emissions not tested engine overheating (8.2.1.2 (d)) | 1 |
| Windscreen damaged and affecting the drivers view of the road stone chip over 10mm in zone A (3.2 (a) (ii)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt split (2.1.3 (g) (ii)) | 1 |
| Nearside Front Road wheel more than one fixing missing (5.2.1 (a) (ii)) | 1 |
| Nearside Windscreen wiper not working (3.4 (a)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill area (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wheel arch area (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill. (6.1.1 (c) (i)) | 1 |
| Nearside Rear reflector missing |1.5.1a| | 1 |
| Offside Rear reflector missing |1.5.1a| | 1 |
| Brake lever has restricted free movement (1.1.15 (e)) | 1 |
| Windscreen wiper not working both front (3.4 (a)) | 1 |
| Nearside Front Brake hose excessively stretched touching wheel on opposite lock (1.1.12 (b) (ii)) | 1 |
| Nearside Rear Parking brake inoperative on one side very low effort (1.4.1 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor holed and corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached bolt (5.3.4 (a) (ii)) | 1 |
| Service brake lagging in operation pedal going to floor (1.2.1 (d)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis inside wheelarch (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded/holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Outersill |2.4.A.3| | 1 |
| Nearside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt arm (5.3.4 (b) (ii)) | 1 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt arm (5.3.4 (b) (ii)) | 1 |
| Offside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt arm (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt arm (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outersill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outersill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Brake lever has insufficient reserve travel NOT WORKING ON NEARSIDE (1.1.2 (a)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill x 2 (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre floor to sill (7.1.1 (a) (i)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits failed before loss of coolant (8.2.1.2 (b)) | 1 |
| Rear Service brake lagging in operation BOTH (1.2.1 (d)) | 1 |
| Offside Front Road wheel more than one fixing loose (5.2.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sills (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sills (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases from joint at front flexi pipe. (6.1.2 (a)) | 1 |
| Nearside Front Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Suspension arm ball joint excessively worn Retaining bolt loose (5.3.4 (a) (i)) | 1 |
| Front Windscreen wiper blade missing both not clearing screen as no blade left (3.4 (b) (ii)) | 1 |
| Offside Rear Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Middle of floor to sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected inner sill |5.3.6 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected closing panel |5.3.6 |a| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced mid outer sill |7.1.1 |a| |i|| | 1 |
| Offside Headlamp aim beam image obviously incorrect adjusters need replacement |1.8.A.1b| | 1 |
| Rear fog lamp not working damaged |1.3.2b| | 1 |
| Headlamp insecure both (4.1.1 (c)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill section. (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Under sill section. (6.1.1 (c) (i)) | 1 |
| Front Brake hose excessively stretched Both (1.1.12 (b) (ii)) | 1 |
| Offside Front Lower Suspension component ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases at front of cat (6.1.2 (a)) | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened around shock mount has split/cut (5.3.3 (b) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam head light faulty (4.1.1 (a) (ii)) | 1 |
| Emissions not tested due to misfire |8.2.1.2 |d|| | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing area |6.1.B.2| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing area |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch = marked |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch = marked |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings marked |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill corroded and holed |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Outer sill corroded and holed |2.4.A.3| | 1 |
| Rear Emissions not tested Due to excessive exhaust leak (8.2.1.2 (d)) | 1 |
| Brake lever has insufficient reserve travel handbrake high (1.1.2 (a)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting 45cms In From OSF Wheel Arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Where Arch Meets Sill (6.2.2 (d) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced on sill (7.1.1 (a) (i)) | 1 |
| Emissions not tested not tested due to missfire (8.2.1.2 (d)) | 1 |
| Supplementary restraint system warning lamp indicates a fault Repaired its self during the test (7.1.6 (a)) | 1 |
| Nearside Front Headlamp levelling device inoperative |1.7.2| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired inner sill and floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Front position lamp|s| obviously incorrectly positioned |1.1.A.3a| | 1 |
| Nearside Front Brake disc significantly and obviously worn severe corrosion (1.1.14 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength front edge of sill corroded + hole (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion rear of sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion to inner sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion to outer sill (7.1.1 (a) (i)) | 1 |
| Position lamp adversely affected by the operation of another lamp all position lamps illuminate when brake pressed (4.2.3 (c)) | 1 |
| Stop lamp(s) adversely affected by the operation of another lamp no brake lamps when sidelights turned on (4.3.3 (b)) | 1 |
| Nearside Front Headlamp light source and lamp not compatible led fitted (4.1.4 (c)) | 1 |
| Offside Front Headlamp light source and lamp not compatible led fitted (4.1.4 (c)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Offside Rear Steering locking device missing track rod end split pin (2.1.3 (d)) | 1 |
| Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Emissions not tested overheating (8.2.1.2 (d)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill at rear (7.1.1 (a) (i)) | 1 |
| Nearside Front Direction indicator light intensity significantly reduced (4.4.3 (a)) | 1 |
| Front Anti-roll bar attachment bracket/mounting insecure (5.3.3 (a) (i)) | 1 |
| Rear fog lamp not working not fitted (4.5.1 (a) (ii)) | 1 |
| Nearside Front Hydraulic brake cylinder leaking hydraulic fluid caliper (1.1.16 (b) (i)) | 1 |
| Offside Front Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance bulb dull.... |1.1.A.3d| | 1 |
| Nearside Front Braking system leaking at `banjo` union area, on calliper..... |3.6.A.1| | 1 |
| Offside Rear Braking system leaking at brake calliper area.... |3.6.A.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill |near previous repair.| |5.2.6| | 1 |
| Offside Front Body panel insecure wings (6.2.1 (a) (i)) | 1 |
| Nearside Body panel insecure body kit (6.2.1 (a) (i)) | 1 |
| Offside Body panel insecure body kit (6.2.1 (a) (i)) | 1 |
| Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
| Offside Front Direction indicator does not face the front (4.4.3 (a)) | 1 |
| Nearside Front Shock absorbers insecurely attached lock nut (5.3.2 (a) (i)) | 1 |
| Offside Front Shock absorbers insecurely attached lock nut (5.3.2 (a) (i)) | 1 |
| Nearside Rear Shock absorbers insecurely attached lock nut (5.3.2 (a) (i)) | 1 |
| Offside Rear Shock absorbers insecurely attached lock nut (5.3.2 (a) (i)) | 1 |
| Nearside Front Seat belt pretensioner missing where fitted as original equipment (7.1.4 (a)) | 1 |
| Offside Front Seat belt pretensioner missing where fitted as original equipment (7.1.4 (a)) | 1 |
| Steering rack cracked and unserviceable |2.2.C.1d| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis under vehicle (6.1.1 (c) (i)) | 1 |
| Inner Front coil spring incomplete |2.4.C.1a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch painted white |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength Inner wheel arch painted white |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill painted white |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill painted white |7.1.1 |a| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front chassis legs (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front chassis legs (6.1.1 (c) (i)) | 1 |
| Nearside Rear Brake hose damaged and likely to fail (1.1.12 (a)) | 1 |
| Battery insecure and likely to cause a short circuit terminals loose (4.13 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system over rear axle (1.1.11 (b) (ii)) | 1 |
| Front Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced in rear wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill 2 x holes (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected box section under wing marked |5.3.6 |a| |ii|| | 1 |
| Offside Front Outer Suspension arm ball joint excessively worn lower (5.3.4 (a) (i)) | 1 |
| Emissions unable to be completed coolant leaked out (8.2.1.2 (d)) | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Headlamp aim projected beam image is obviously incorrect both n/s and o/s (4.1.2 (c)) | 1 |
| Emissions unable to be completed co excessively high (8.2.2.2 (e)) | 1 |
| Rear fog lamp does not emit a steady red light white light (4.5.4 (a)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch (6.2.2 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre to rear gasket (6.1.2 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Body panel corroded and likely to cause injury wing |6.2.1 |a| |i|| | 1 |
| Offside Front Lower Body panel corroded and likely to cause injury wing |6.2.1 |a| |i|| | 1 |
| Offside Front Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 1 |
| Nearside Power steering component|s| leaking rack |2.3.3b| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Body panel damaged and likely to cause injury both front wing . (6.2.1 (a) (i)) | 1 |
| Rear fog lamp tell tale missing (1.3.1b) | 1 |
| Offside Front Steering rack gaiter insecure (2.2.D.2d) | 1 |
| Offside Front Anti-roll bar linkage severely distorted (2.4.G.1) | 1 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive (7.3.D.3) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill next to suspension arm (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill next to suspension arm (5.3.6 (a) (i)) | 1 |
| Service brake: efficiency below requirements (3.7.B.7) | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2) | 1 |
| Offside Front Integral body structure inadequately repaired such that structural rigidity is significantly reduced inner sill front (6.1.1 (d) (i)) | 1 |
| Rear Suspension arm cracked |2.4.G.1| | 1 |
| Parking brake inoperative on one side both (1.4.1 (a)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced center inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Outer Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting at o/s/f anti roll bar mtg. (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting behind o/s/f subframe mtg. (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure inadequately repaired such that structural rigidity is significantly reduced outer sill panel not welded (6.1.1 (d) (i)) | 1 |
| Nearside Rear Vehicle structure inadequately repaired such that structural rigidity is significantly reduced outer sill not welded (6.1.1 (d) (i)) | 1 |
| Offside Parking brake inoperative on one side efficiency low (1.4.1 (a)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor area (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| All direction indicators not working All not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced SILL (7.1.1 (a) (i)) | 1 |
| Rear Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Offside Front Upper Suspension arm likely to become detached No split pin (5.3.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch area (5.3.6 (a) (i)) | 1 |
| Horn not working only intermitant |1.6.2a| | 1 |
| Nearside Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Power steering pipe|s| or hose|s| excessively corroded pipes on rack |2.3.2| | 1 |
| Rear Service brake excessively binding Brakes (1.2.1 (f)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill end (7.1.1 (a) (i)) | 1 |
| Integral body structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light showing white light (4.5.4 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floorpan (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill to floorpan (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill to floorpan (5.3.6 (a) (i)) | 1 |
| Nearside Front Brake hose excessively stretched not long enough in full lock (1.1.12 (b) (ii)) | 1 |
| Nearside Front Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Nearside Front Macpherson strut attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Offside Front Macpherson strut attachment bracket/mounting insecure and impairing directional stability top securing nuts missing (5.3.3 (a) (ii)) | 1 |
| Offside Rear Brake hose excessively stretched flexi pipe fowling rear wheel rim (1.1.12 (b) (ii)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill/floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Arch/sill (6.1.1 (c) (i)) | 1 |
| Front Steering rack gaiter missing or no longer prevents the ingress of dirt Both gaiters (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Hydraulic brake calliper leaking Brake fluid leaking from calliper, Although brake performance is within required limits. (1.1.16 (b) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill corroded in several places (6.1.1 (c) (i)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Exhaust emits clearly visible black smoke during acceleration |7.3.A.2c| | 1 |
| Brake hydraulic reservoir fluid level significantly below minimum level empty (1.1.10 (d) (ii)) | 1 |
| Brake performance not tested brake pedel going straight to floor and brake fluid bottle empty (1.2.1 (g)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system brake pipe corroded and leaking (1.1.11 (b) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system BURST ON BRAKE TESTER. FRONT TO REAR BRAKE PIPE (1.1.11 (b) (ii)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wheel Arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Boot Floor area (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS LEG (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS LEG ALSO HOLED AT INNER ARCH (5.3.6 (a) (i)) | 1 |
| Rear Parking |secondary brake| on a single line braking system has no recorded effort at a wheel BOTH NIL |1.3.1 |a| |ii|| | 1 |
| Subframe mounting prescribed area is excessively corroded both sides front chassis |2.4.A.3| | 1 |
| Suspension arm corroded and seriously weakened both front bottom shocker mounts to arm |2.4.G.1| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Lower Suspension rod attachment bracket/mounting insecure and impairing directional stability bolt snapped |5.3.3 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis leg anti-roll bar mounting area |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Lower sill area |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Outer sill area |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Inner wheelarch area |5.2.6| | 1 |
| Rear fog lamp obviously incorrectly positioned uses stop lamp (4.5.4 (a)) | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting within 30cm off o/s seatmounting (6.2.2 (d) (i)) | 1 |
| Offside Front Upper Suspension arm insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Headlamp aim projected beam image is obviously incorrect both front (4.1.2 (c)) | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Rear Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner chassis leg (5.3.6 (a) (i)) | 1 |
| Rear Axle insecure such that functionality is affected (5.1.1 (b) (ii)) | 1 |
| Offside Rear Suspension component missing axle mount bush nut missing (5.3.3 (a) (ii)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure fixing missing (5.3.3 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre to rear (6.1.2 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer sill and floor to sill |5.2.6| | 1 |
| Brake performance not tested brake fluid leak (1.2.1 (g)) | 1 |
| Nearside Rear Brake pedal does not operate a brake fitted to each wheel |3.3.A.3| | 1 |
| Offside Rear Brake pedal does not operate a brake fitted to each wheel |3.3.A.3| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to inner sill (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced middle floor to inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn bottom ball joint (5.3.4 (a) (i)) | 1 |
| Nearside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Stop lamp(s) adversely affected by the operation of another lamp remains on with sidelights but does not work with brake lights (4.3.3 (b)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis . |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner arches/outer sill panel. |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner arches /outer sill panel. |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Upper Suspension arm pin or bush excessively worn inner bushes causing arm to foul subframe (5.3.4 (a) (i)) | 1 |
| Rear coil spring fractured |2.4.C.1a| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced pattern too poor |1.7.5a| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Exhaust emits visible black smoke at idle (8.2.1.2 (f)) | 1 |
| Front Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Front Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Parking brake inoperative on one side no effort from caliper cable working (1.4.1 (a)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill end (6.1.1 (c) (i)) | 1 |
| Nearside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Nearside Seat belt buckle missing (7.1.2 (d)) | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jack point (6.1.1 (c) (i)) | 1 |
| Nearside Stop lamp(s) adversely affected by the operation of another lamp Coming on with rear fog lamp switch. (4.3.3 (b)) | 1 |
| Headlamp aim projected beam image is obviously incorrect Both. No proper beam patterns. (4.1.2 (c)) | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded bulkhead/Inner wing areas at mounting. (1.1.21 (e) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill holed and corroded. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired Sill end behind roadwheel. (Catalloy) (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill end and inner wheel arch holed and corroded. Behind road wheel. (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired Sill end and inner wheel arch behind roadwheel. (5.3.6 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area is inadequately repaired Mid Sill. (Catalloy) (7.1.1 (a) (i)) | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded inner wheel arch (2.1.2 (e) (i)) | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded inner wheel arch (2.1.2 (e) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits CO READING VERY HIGH (8.2.1.2 (a)) | 1 |
| Power steering pipe/hose leaking front behind grill (2.1.5 (a)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill end inner (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill end (7.1.1 (a) (i)) | 1 |
| Nearside Front Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting CHASSIS RAIL (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill and split |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis in wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis in wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Rear sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Rear sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced INNER AND OUTER SILL (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced INNER AND OUTER SILL (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Offside Front Upper Suspension arm insecure and impairing directional stability Inner fixing nut and bolt loose (5.3.3 (a) (ii)) | 1 |
| Nearside Steering locking device ineffective Outer track rod end locking nut loose (2.1.3 (d)) | 1 |
| Offside Front Headlamp light intensity severely reduced dip beam (4.1.4 (a)) | 1 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner arch - multiple sections (5.3.6 (a) (i)) | 1 |
| Nearside Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis section (5.3.6 (a) (i)) | 1 |
| Offside Front Brake pipe connection leaking on a hydraulic braking system under bonnet (1.1.11 (b) (ii)) | 1 |
| Offside Front Position lamp likely to become detached (4.2.1 (c) (ii)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner arch - multiple sections (5.3.6 (a) (i)) | 1 |
| Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Rear Anti-roll bar corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Rear Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 1 |
| Centre Rear fog lamp not visible from a reasonable distance |1.1.6b| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Stop lamp(s) all not working no break lights (4.3.1 (a) (iii)) | 1 |
| All direction indicators not working no indicators or hazard lights (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wing/Chassis rail. (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Jacking point/Sill corroded through!! (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill corroded/holed within 30cm of seat belt mounting (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill corroded/holed within 30cm of seat belt mounting (7.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg corroded/holed on floor pan (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill corroded/holed (6.1.1 (c) (i)) | 1 |
| Brake performance not tested leaking brake pipe (1.2.1 (g)) | 1 |
| Brake pipe at imminent risk of failure or fracture front to rear, corroded and leaking (1.1.11 (a)) | 1 |
| Offside Front Coil spring fractured or broken broken (5.3.1 (b) (i)) | 1 |
| Emissions not tested engine temperature to high starting to overheat (8.2.1.2 (d)) | 1 |
| Offside Front Steering locking device ineffective (2.1.3 (d)) | 1 |
| Offside Front Track rod end seriously misaligned (2.1.3 (e)) | 1 |
| Rear Sub-frame attachment bracket/mounting insecure rear sub frame /differential bushes are excessively corroded on the metal portion (5.3.3 (a) (i)) | 1 |
| Emissions not tested Battery died (8.2.1.2 (d)) | 1 |
| Stop lamp(s) remains on when the brakes are released (4.3.2 (a) (iii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Wishbone mounting (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg by headlamp mounting (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg by headlamp mounting (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Offside Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired corroded through ns outer passenger floor within 30 cm mount (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ARCH AREA |5.3.6 |a| |i|| | 1 |
| Emissions not tested excessive blow front pipe to cat (8.2.1.2 (d)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits Due to exhaust blow (8.2.1.2 (c)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak Cat to center pipe, Center pipe to rear box joints both badly leaking (8.2.1.1 (b)) | 1 |
| Rear Service brake effort inadequate at a wheel Both rear (1.2.1 (a) (i)) | 1 |
| Offside Rear Upper Suspension arm pin or bush excessively worn outer bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Nearside Seat belt anchorage loose not attached at lower point (7.1.1 (b)) | 1 |
| Emissions not tested DUE TO EXCESSIVE EXHAUST BLOW (8.2.1.2 (d)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.92% (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits 0.93% (8.2.1.2 (b)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill corrosion at rear (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outter sill (7.1.1 (a) (i)) | 1 |
| Emissions not tested Due to major exhaust leak (8.2.1.2 (d)) | 1 |
| Nearside Parking brake inoperative on one side poor (1.4.1 (a)) | 1 |
| Offside Parking brake inoperative on one side poor (1.4.1 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced undersills (7.1.1 (a) (i)) | 1 |
| Offside front brake binding 25kg |3.7.B.1| | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail (6.2.2 (d) (i)) | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive slight leak of gases after cat converter |7.3.D.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg in wheel arch rear roll bar mount |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg in wheel arch rear roll bar mount |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis leg by anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg above arm mount (6.2.2 (d) (i)) | 1 |
| Nearside Rear Lower Suspension arm severely distorted |2.4.G.1| | 1 |
| Offside Rear Lower Suspension arm severely distorted |2.4.G.1| | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced central floor pan (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Suspension arm attachment bracket/mounting insecure and impairing directional stability Front fixing loose (5.3.3 (a) (ii)) | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect and o/s/f |1.8.A.1b| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under arch front (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced jacking point (7.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer floor jacking point (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength corroded (5.3.6 (a) (i)) | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases rear silencer blowing (6.1.2 (a)) | 1 |
| Offside Front Headlamp has a product on the light source which changes emitted colour to other than white or yellow |4.1.4 |b|| | 1 |
| Nearside Front Headlamp has a product on the light source which changes emitted colour to other than white or yellow |4.1.4 |b|| | 1 |
| Central Brake pipe leaking on a hydraulic braking system main brake pipe to rear. do not drive (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Central Rear Stop lamp(s) not working high level (4.3.1 (a) (ii)) | 1 |
| Emissions not tested due to major exhaust blow (8.2.1.2 (d)) | 1 |
| Nearside Rear Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front Brake disc fractured (1.1.14 (a) (ii)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill has 3 holes in (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Headlamps matched pair are not the same colour n/s yellow, o/s white (4.1.4 (d)) | 1 |
| Rear fog lamp does not emit a steady red light wrong colour (4.5.4 (a)) | 1 |
| Nearside Direction indicator adversely affected by the operation of another lamp side lights (4.4.3 (b)) | 1 |
| Nearside Front Anti-roll bar linkage insecurely attached nut and bolt loose (5.3.3 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage insecurely attached nut and bolt loose (5.3.3 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill excessively corroded (7.1.1 (a) (i)) | 1 |
| Headlamp aim unable to be tested not tested as the pop up lights do not raise (4.1.2 (b)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits 0.99% (8.2.1.2 (a)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits 0.74% (8.2.1.2 (b)) | 1 |
| Nearside Front Suspension arm pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced complete sill front - rear (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor To Sill (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor To Sill (7.1.1 (a) (i)) | 1 |
| Emissions not tested Due to exhaust blow (8.2.1.2 (d)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front and rear of sill (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front and rear sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar linkage attachment bracket/mounting likely to fail (5.3.3 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage attachment bracket/mounting likely to fail (5.3.3 (b) (ii)) | 1 |
| Emissions not tested rear exhaust snapped (8.2.1.2 (d)) | 1 |
| Offside Front Headlamp does not operate immediately when selected on dipped beam |1.7.4a| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Windscreen wiper blade missing (3.4 (b) (ii)) | 1 |
| Nearside Headlamp not working on dipped beam n/s headlamp not rising to foreward facing position when operated, so neither beam working (4.1.1 (a) (ii)) | 1 |
| Exhaust system insecure centre exhaust mounting not attached (6.1.2 (a)) | 1 |
| Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Rear Brake disc significantly and obviously worn both (1.1.14 (a) (i)) | 1 |
| Nearside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users Major coolant leak (8.4.1 (a) (i)) | 1 |
| Emissions unable to be completed Major coolant leak (8.2.1.2 (d)) | 1 |
| Offside Front Anti-roll bar linkage insecurely attached drop link insecure (5.3.3 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill |chalked| |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar attachment area |2.4.A.3| | 1 |
| Driver`s seat fore and aft adjustment mechanism not functioning as intended. |6.2.5 |b| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg (6.1.1 (c) (i)) | 1 |
| Nearside Front Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases Middle- Rear silencer join rusted away |7.1.2| | 1 |
| Power steering pipe|s| or hose|s| excessively corroded Pipes to the rack |2.3.2| | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn lower joint |5.3.4 |a| |i|| | 1 |
| Offside Rear fog lamp does not emit a steady red light INCORRECT COLOUR (4.5.4 (a)) | 1 |
| Offside Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting SILL - ( 48CM IN LENGTH WEAK OF SILL ) (6.2.2 (d) (i)) | 1 |
| Nearside Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting SILL - ( APPROX 13CM IN LENGTH ) (6.2.2 (d) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect - ( AIM NOT CORRECT ) (4.1.2 (c)) | 1 |
| Nearside Rear Hydraulic brake calliper excessively weakened by corrosion IN OPERATIVE - ( STICKING / LOCKED ON / SIEZED ) (1.1.16 (d) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases - ( SILENCER CORRODED / LEAKING / SPLIT OUTER SKIN ) (6.1.2 (a)) | 1 |
| Service brake excessively binding - ( REAR / FRONT - BTH AXLES ) (1.2.1 (f)) | 1 |
| Nearside Front Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Nearside & offside |6.1.1 |c| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner arch |7.1.1 |a| |i|| | 1 |
| Nearside Front Lower Suspension component ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Rear Upper Suspension component insecurely attached hub assembly |5.3.3 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases center |7.1.2| | 1 |
| Central Exhaust has a major leak of exhaust gases Before Catalytic Converter (6.1.2 (a)) | 1 |
| Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded |7.1.1 |a| |i|| | 1 |
| Central Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Central Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL HOLED |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL HOLED |5.3.6 |a| |i|| | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Brake hose leaking on a hydraulic braking system at caliper (1.1.12 (c) (ii)) | 1 |
| Offside Front Seat belt damaged (7.1.2 (b) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced x 2 in wheel arch chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Nearside Rear Brake lining|s| less than 1.5 mm thick |1.1.13 |a| |ii|| | 1 |
| Offside Rear Brake lining|s| less than 1.5 mm thick |1.1.13 |a| |ii|| | 1 |
| Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill/rear quarter area (5.3.6 (a) (i)) | 1 |
| Offside Front Braking system leaking caliper union |3.6.A.1| | 1 |
| Nearside Front Coil spring fractured or broken broken (5.3.1 (b) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded within 30cms of anti roll bar mounting points. (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint likely to become detached detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced hole in floor within prescribed area off seat belt mounting |7.1.1 |a| |i|| | 1 |
| Offside Front Track rod end ball joint has excessive play LOOSE ON TAPPER IN STUB AXLE (2.1.3 (b) (i)) | 1 |
| Offside Front Lower Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Upper Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Upper Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Suspension component insecurely attached Split pin missing from castlated nut. (5.3.3 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg. (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension turret marked in yellow chalk (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits 0.299 should be under 0.200 (8.2.1.2 (b)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits reading was 1.116 should be under 1.030 (8.2.1.2 (c)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Body (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Body panel damaged and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases EXHAUST JOINT CORRODED |7.1.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded FLOOR |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded FLOOR |5.2.6| | 1 |
| Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Steering system has a road wheel fouling a part of the vehicle |2.2.D.2a| | 1 |
| Offside Headlamp not working on dipped beam (1.7.5a) | 1 |
| Nearside Headlamp not working on dipped beam (1.7.5a) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 1 |
| Parking (secondary brake) on a single line braking system has no recorded effort at a wheel both rear (1.3.1 (a) (ii)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced FLOOR (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced FLOOR (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced INNER SILL (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL /WHEEL ARCH (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced INNER SILL (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL/ ARCH (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sell |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis|inner arch| |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis|inner arch| |2.4.A.3| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill to floor (6.2.2 (d) (i)) | 1 |
| Offside Front Upper Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear silencer |7.1.2| | 1 |
| Offside Rear Brake pipe at imminent risk of failure or fracture front to rear brake pipe corroded (1.1.11 (a)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced n/s/f chassie leg under the wheel arch has rust holes (6.1.1 (c) (i)) | 1 |
| Brake performance not tested brake test aborted because of the brake pipe burst on brake tester (1.2.1 (g)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak silencer |8.2.1.1 |b|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded upper sill in front of rear wheel |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill excessively corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL PANEL... (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer Sill/Wheel Arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sub frame mount area marked (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill heavily corroded (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill heavily corroded (7.1.1 (a) (i)) | 1 |
| Steering box leaking to the extent that oil is dripping power steering pipe leaking (2.1.1 (e) (ii)) | 1 |
| Coil spring fractured or broken all (5.3.1 (b) (i)) | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill, inner and outer |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings front of inner wheel arch |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings front of inner wheel arch |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill, inner |6.1.B.2| | 1 |
| Rear Stop lamp(s) not working Hi level stop lamp bulb connection remade and relocated in light unit to rectify (4.3.1 (a) (ii)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded Sill corroded |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded and has whole (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded and has whole (7.1.1 (a) (i)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak centre exhaust box leaking (8.2.1.1 (b)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak exhaust silencer leaking (8.2.1.1 (b)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill/body |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill/body |5.2.6| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering Outer sill rusted |6.1.A.1| | 1 |
| Nearside Inner Vehicle structure has excessive corrosion which adversely affects braking or steering Sill rusted |6.1.1 |c| |ii|| | 1 |
| Offside Inner Vehicle structure has excessive corrosion which adversely affects braking or steering Sill rusted |6.1.1 |c| |ii|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor/chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened by shockabsorber mount. (5.3.3 (b) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced lower arch/sill (7.1.1 (a) (i)) | 1 |
| Offside Rear fog lamp obviously incorrectly positioned |1.3.2a| | 1 |
| Emissions unable to be completed misfire present (8.2.1.2 (d)) | 1 |
| Offside Front Suspension arm attachment bracket/mounting corroded and seriously weakened floor and close to seat mount (5.3.3 (b) (i)) | 1 |
| Battery insecure and likely to fall from carrier rear battery tray corroded through floor |4.13 |a| |ii|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Floor |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 1 |
| Offside Front Seat belt missing 4 point harness fitted with no fixed clasp (7.1.2 (a)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor / sill area marked in yellow (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill area marked in yellow (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Rear Service brake imbalanced across an axle (1.2.1 (b) (i)) | 1 |
| Front Side repeater incorrect colour |1.4.A.2f| | 1 |
| Nearside Obligatory mirror insecure (3.3 (b) (ii)) | 1 |
| Nearside Front Lower Body component insecure wing (6.2.1 (a) (i)) | 1 |
| Offside Front Lower Body component insecure wing (6.2.1 (a) (i)) | 1 |
| Offside Front Lower Suspension component insecurely attached ball joint split pin missing (5.3.3 (a) (i)) | 1 |
| Nearside Front Upper Suspension component insecurely attached ball joint split pin missing (5.3.3 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases middle joint (6.1.2 (a)) | 1 |
| Nearside Rear Seat belt anchorage likely to become detached in the event of a collision outer sill inner sill andinner wheel arch excessively corroded and holed (7.1.1 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired outer sill holed full of filler (7.1.1 (a) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired drivers main a pillar fibreglass repair (6.2.2 (d) (ii)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Fuel system component leaking Under bonnet - Rear of fuel rail area (6.1.3 (b) (i)) | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to arch (6.1.1 (c) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor |7.1.1 |a| |i|| | 1 |
| Nearside Rear Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Offside Rear Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases section (6.1.2 (a)) | 1 |
| Offside Front Hydraulic fluid leaking continuously posing a serious risk to road safety brake pipe |8.4.1 |a| |ii|| | 1 |
| Headlamp lens seriously defective both (4.1.1 (b) (ii)) | 1 |
| Offside Front Inner Integral body structure has excessive corrosion which adversely affects braking or steering w/arch (6.1.1 (c) (ii)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill x2 (6.1.1 (c) (i)) | 1 |
| Offside Front Wheel stud|s| missing |4.2.A.1e| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner/outer sill |7.1.1 |a| |i|| | 1 |
| Front Headlamp aim beam image obviously incorrect both headlamp lenses are faded |1.8.A.1b| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill to wheel arch and inner sill |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis rail in many places |2.4.A.3| | 1 |
| Electrical wiring insecure front to rear |1.9.2a| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt drop link (5.3.4 (b) (ii)) | 1 |
| Nearside Front Lower Shock absorbers insecurely attached incorrect size bolt used significantly smaller than design (5.3.2 (a) (i)) | 1 |
| Fuel cap/sealing device ineffective cannot check cap (6.1.3 (b) (i)) | 1 |
| Nearside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Front Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Brake hydraulic reservoir fluid level decreases after several pedal applications |3.3.C.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front chassis |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front chassis |5.3.6 |a| |i|| | 1 |
| Nearside Rear fog lamp obviously incorrectly positioned |1.3.2a| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect and offside (4.1.2 (c)) | 1 |
| brake caliper securing device loose both sides |3.5.1j| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside rear (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Brake cable damaged (1.1.15 (a)) | 1 |
| Nearside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Lower Brake pipe likely to become detached or damaged (1.1.11 (d) (ii)) | 1 |
| Centre Upper Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Centre Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel and floor pan |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis anti roll bar mounting |2.4.A.3| | 1 |
| Headlamp aim not tested lenses misted (4.1.2 (b)) | 1 |
| Brake pipe leaking Front to rear |3.6.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Wheel arch |2.4.A.3| | 1 |
| Offside Front Outer Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Offside Rear Wheel nut|s| loose x4 |4.2.A.1e| | 1 |
| Nearside Rear Wheel nut|s| loose x4 |4.2.A.1e| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing /chassis rail |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch/chassis rail |2.4.A.3| | 1 |
| Offside Outer Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed within prescribed area (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill area |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis area |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis area |2.4.A.3| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar linkage fractured |5.3.3 |b| |ii|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 1 |
| Nearside Brake hose excessively twisted (1.1.12 (b) (ii)) | 1 |
| Nearside Front front brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis under wheel arch |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis under wheel arch |6.1.B.2| | 1 |
| Parking brake lever has no reserve travel (3.1.6b) | 1 |
| Rear fog lamp emits a light other than red (1.3.2e) | 1 |
| Offside Rear brake caliper leaking (3.6.A.1) | 1 |
| Rear fog lamp missing (1.3.2a) | 1 |
| Nearside Lower Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Offside Lower Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Offside Rear Lower Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Front Lower Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Emissions unable to be completed exhaust condition does not allow a test to be performed (8.2.1.2 (d)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Offside Front Floor excessively deteriorated (6.2.4 (a) (i)) | 1 |
| Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Rear Anti-roll bar ball joint likely to become detached detached |5.3.4 |a| |ii|| | 1 |
| Suspension arm ball joint excessively worn both front lower |5.3.4 |a| |i|| | 1 |
| Rear Stop lamp|s| not working centre |4.3.1 |a| |ii|| | 1 |
| Steering column universal joint is excessively deteriorated |2.1.5| | 1 |
| Nearside Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill Corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Front suspension retaining device missing castle nut split pin missing |2.5.A.4| | 1 |
| Offside Front Lower Front suspension retaining device missing castle nut split pin missing |2.5.A.4| | 1 |
| Offside Front Lower Suspension arm attachment bracket/mounting insecure and impairing directional stability |5.3.3 |a| |ii|| | 1 |
| Central Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Front Fluid leak harmful to the environment or a risk to other road users power steering (8.4.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ANTI ROLL BAR MOUNT (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength ANTI ROLL BAR MOUNT (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Battery tray (5.3.6 (a) (i)) | 1 |
| Offside Front Position lamp not working sidelight |4.2.1 |a|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced FLOOR |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SILL |7.1.1 |a| |i|| | 1 |
| Nearside Outer Front Upper Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wing |2.4.A.3| | 1 |
| Offside Rear Rear position lamp|s| not working replaced bulb |1.1.A.3b| | 1 |
| Obligatory mirror is incapable of being adjusted to provide an adequate view to the rear adjuster missing |8.1.2b| | 1 |
| Steering wheel has movement relative to the column such that there is a serious risk of detachment |2.2.1 |a| |ii|| | 1 |
| Offside Driver`s airbag missing |7.1.5 |a|| | 1 |
| Nearside Front position lamp|s| has a product on the lens so it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front position lamp|s| has a product on the lens so it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Suspension arm locating pin retaining device missing all 4 |2.4.G.3b| | 1 |
| Offside Rear Braking system leaking cal |3.6.A.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded under sill |2.4.A.3| | 1 |
| Nearside Rear Inner Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Inner Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Brake pipe leaking on a hydraulic braking system main brake pipe under rear securing clip (1.1.11 (b) (ii)) | 1 |
| Brake performance unable to be tested brake fluid leak (1.2.1 (g)) | 1 |
| Brake pedal anti-slip provision loose split |1.1.2 |c|| | 1 |
| Headlamp light intensity severely reduced both sides |4.1.4 |a|| | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn broken |5.3.4 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis |7.1.1 |a| |i|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced and rear chassis (6.1.1 (c) (i)) | 1 |
| Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt both arms (5.3.4 (b) (ii)) | 1 |
| Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt both arms (5.3.4 (b) (ii)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg abover anti roll bar (5.3.6 (a) (i)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced BOTH FRONT (4.1.4 (b)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak REAR SILENCER (8.2.1.1 (b)) | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Front Headlamp lens seriously defective both sides (4.1.1 (b) (ii)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect both sides (4.1.2 (c)) | 1 |
| Offside Rear Anti-roll bar linkage insecure and impairing directional stability upper ball joint detached (5.3.3 (a) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor Corroded |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor Corroded |7.1.1 |a| |i|| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch |5.3.6 |a| |i|| | 1 |
| Oil leaking excessively from engine engine oil |8.4.1 |a| |i|| | 1 |
| Nearside Inner Front brake disc excessively scored |3.5.1h| | 1 |
| Offside Inner Front brake disc excessively scored |3.5.1h| | 1 |
| Indicator switch inoperative (4.4.2 (a) (ii)) | 1 |
| Offside Power steering component leaking steering rack end seal leaking heavily (2.1.5 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced rear of sill corroded through (7.1.1 (a) (i)) | 1 |
| Offside Hydraulic fluid leaking excessively steering rack leaking |8.4.1 |a| |i|| | 1 |
| Nearside Subframe mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength battery tray (5.3.6 (a) (i)) | 1 |
| Brake pipe leaking on an air braking system Front to rear |1.1.11 |b| |i|| | 1 |
| Nearside Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced body sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced body sill (7.1.1 (a) (i)) | 1 |
| Offside Front Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor |6.1.1 |c| |i|| | 1 |
| Offside Rear Lower Anti-roll bar ball joint likely to become detached is detatched |5.3.4 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cill |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced cill front and middle |7.1.1 |a| |i|| | 1 |
| Offside Front Headlamp aim not tested Inoperative dip beam. |4.1.2 |b|| | 1 |
| Nearside Front Side repeater not working Wing repeater. |4.4.1 |a| |ii|| | 1 |
| Emissions not tested excessive exhaust leak |8.2.1.2 |d|| | 1 |
| Exhaust has a major leak of exhaust gases rear and front pipe |6.1.2 |a|| | 1 |
| Offside Rear Hydraulic fluid leaking continuously posing a serious risk to road safety brakes |8.4.1 |a| |ii|| | 1 |
| Offside Front Braking system leaking to rear |3.6.A.1| | 1 |
| Front Position lamp not working BOTH FRONT POSITION LAMPS INOP (4.2.1 (a) (ii)) | 1 |
| Central Rear Stop lamp(s) not working CHMSL INOP (4.3.1 (a) (ii)) | 1 |
| Nearside Upper Front suspension retaining device missing |2.5.A.4| | 1 |
| Parking brake lever releases when knocked |3.1.6a| | 1 |
| Parking brake lever ratchet mechanism is excessively worn |3.1.5| | 1 |
| Brake pipe leaking on a hydraulic braking system Front to rear |1.1.11 |b| |ii|| | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Nearside Front Upper Suspension component likely to become detached Locking nut has split pin missing |5.3.3 |a| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Rear inner sill under drivers seat |5.2.6| | 1 |
| Offside Rear fog lamp obscured more than 50% |1.3.2c| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength under bonnet side of wheel arche (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/ wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Floor excessively deteriorated (6.2.4 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced central floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Front Anti-roll bar linkage attachment bracket/mounting fractured |5.3.3 |b| |ii|| | 1 |
| Nearside Front Vehicle structure has a fracture which adversely affects braking or steering Anti roll bar mount bracket |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Anti roll bae mounting bracket |6.1.A.1| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nearside centre floor to inner sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is inadequately repaired offside centre floor to inner sill- repair patch not fully seam welded |5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer to centre pipe |6.1.2 |a|| | 1 |
| Headlamp lens seriously defective both side (4.1.1 (b) (ii)) | 1 |
| Offside Rear Shock absorbers likely to become detached (5.3.2 (a) (ii)) | 1 |
| Offside Parking brake inoperative on one side very low effort (1.4.1 (a)) | 1 |
| Front Power steering pipe|s| or hose|s| leaking return pipe/hose |2.3.3b| | 1 |
| Nearside Rear Body panel corroded and likely to cause injury arch (6.2.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL |7.1.1 |a| |i|| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings o/s rear sill |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings o/s rear inner sill |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s rear sill |6.1.B.2| | 1 |
| Offside Front Vehicle structure is so deformed it is likely to adversely affect braking or steering |6.1.1 |a| |ii|| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Front Lower Suspension component mounting prescribed area is excessively corroded both sides of car, chassis! |2.4.A.3| | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering both sides around anti roll bar mountings |6.1.A.1| | 1 |
| Nearside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced under side of chassis between roll bar and rack area holed! |6.1.1 |c| |i|| | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced under side of chassis between roll bar and rack area holed! |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail under side (6.1.1 (c) (i)) | 1 |
| Power steering component leaking steering rack leaking (2.1.5 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER CHASSIC LEG NEAR INNER WING (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits 6.5 (8.2.1.2 (b)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn drop link (5.3.4 (a) (i)) | 1 |
| Offside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed plus weak (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed plus weak (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill to floor holed (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded OUTER SILL |5.2.6| | 1 |
| Offside Driver`s door cannot be opened from outside the vehicle |6.2.3 |a|| | 1 |
| Offside Driver`s door cannot be opened from inside the vehicle |6.2.3 |a|| | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement temporary cap |7.2.4b| | 1 |
| Front position lamp|s| not working both front |1.1.A.3b| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end plus wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under passenger seat |6.1.B.2| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed and corroded |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed and corroded |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail corroded |5.3.6 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail holed (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Front suspension locking device ineffective |2.5.A.4| | 1 |
| Seat belt anchorage prescribed area is excessively corroded O/S/R Sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded N/S/R Sill |5.2.6| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering N/S/F Chassis Leg |6.1.A.1| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering O/S/F Chassis Leg |6.1.A.1| | 1 |
| Nearside Front Headlamp excessively damaged so that the light output is severely reduced and o/s/f blurred images |1.7.5a| | 1 |
| Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Offside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill corroded and holed (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Corroded and holed (6.2.2 (d) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded inner flitch |2.4.A.3| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded Chassis |2.4.A.3| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded ach chassie rail by upper suspension arm |2.4.A.3| | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid brake calliper (1.1.16 (b) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage inappropriately repaired |2.4.A.2| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Coil spring fractured or broken O/S/F (5.3.1 (b) (i)) | 1 |
| Suspension arm pin or bush excessively worn MAJOR PLAY IN N/S/R (ALL DIRECTIONS) >> INVESTIGATION AND REPAIR REQUIRED (5.3.4 (a) (i)) | 1 |
| Offside Power steering ram|s| leaking from a failed component |2.3.3b| | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Rear reflector missing |1.5.1a| | 1 |
| Nearside Rear Rear reflector missing |1.5.1a| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect bulb issue. (4.1.2 (c)) | 1 |
| Exhaust has a major leak of exhaust gases joint at front to middle section. (6.1.2 (a)) | 1 |
| Nearside Front Anti-roll bar linkage insecurely attached nuts are loose. (5.3.3 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced 2 bits corroded and holed. (6.1.1 (c) (i)) | 1 |
| Nearside Front Body component corroded and likely to cause injury wheel arch is corroded and holed and has sharp edges showing. (6.2.1 (a) (i)) | 1 |
| Emissions not tested due to major leak of gases. (8.2.1.2 (d)) | 1 |
| Nearside Front position lamp|s| flickers when tapped lightly by hand |1.1.4c| | 1 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired chassis has a plate riveted on but requires welding |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Power steering ram leaking (2.1.5 (a)) | 1 |
| Offside Rear Tie bar/rod attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering by Inner Wheel Arch |6.1.A.1| | 1 |
| Nearside Hydraulic fluid leaking excessively bellow steering rack |8.4.1 |a| |i|| | 1 |
| Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
| Nearside Stop lamp(s) showing white light to the rear (4.3.3 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail above anti roll bar (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL PANEL (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced CHASSIS NEXT ANTI ROLL BAR (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced NEXT TO ANTI ROLL BAR MOUNTING (6.1.1 (c) (i)) | 1 |
| Emissions not tested no reading from rear tailpipe |7.3.A.1| | 1 |
| Exhaust has a major leak of exhaust gases centre and rear joining flange |7.1.2| | 1 |
| Nearside Rear Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outersill area (7.1.1 (a) (i)) | 1 |
| Front Subframe mounting prescribed area is excessively corroded nearside and offside |2.4.A.3| | 1 |
| Offside Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill. (6.1.1 (c) (i)) | 1 |
| Front Power steering pipe/hose leaking under steering rack. (2.1.5 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill /floor (7.1.1 (a) (i)) | 1 |
| Offside Floor excessively deteriorated floor to sill (6.2.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Anti-roll bar ball joint excessively worn droplink (5.3.4 (a) (i)) | 1 |
| Offside Front Outer Suspension arm ball joint dust cover no longer prevents the ingress of dirt lower arm (5.3.4 (b) (ii)) | 1 |
| Nearside Front Outer Suspension arm ball joint dust cover no longer prevents the ingress of dirt lower arm (5.3.4 (b) (ii)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt outer upper control arm (5.3.4 (b) (ii)) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt outer upper control arm (5.3.4 (b) (ii)) | 1 |
| Offside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened lower am excess play (5.3.3 (b) (i)) | 1 |
| Offside Front Inner Suspension arm pin or bush excessively worn inner rear to control arm (5.3.4 (a) (i)) | 1 |
| Emissions not tested emissions failing (8.2.1.2 (d)) | 1 |
| Nearside Rear Brake hose leaking |3.6.A.1| | 1 |
| Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing/chassis |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded CHASIE LEG |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded CHASIE LEG |5.2.6| | 1 |
| Offside Front Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings CHASIE LEG |6.1.B.2| | 1 |
| Exhaust has a major leak of exhaust gases AT CAT |7.1.2| | 1 |
| Nearside Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Parking brake lever ratchet mechanism is broken does not stay in the on position |3.1.5| | 1 |
| Offside Front Headlamp insecure bracket broken |1.7.3| | 1 |
| Offside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits co reading to high (8.2.1.2 (b)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits lambda reading to high (8.2.1.2 (c)) | 1 |
| Nearside Front Headlamp not working on dipped beam front n/s head light not working (4.1.1 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill excessively corroded !! (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced n/s rear outer lower sill corroded (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced o/s rear inner sill corroded (6.1.1 (c) (i)) | 1 |
| Rear Service brake effort inadequate at a wheel rear service brake [foot brake ] and handbrake showing low effort at rear wheels (1.2.1 (a) (i)) | 1 |
| Offside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill corroded |6.1.1 |c| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill in several places |5.2.6| | 1 |
| Hydraulic fluid leaking excessively power steering system (8.4.1 (a) (i)) | 1 |
| Brake pedal anti-slip provision missing brake pedal rubber missing |3.3.A.1b| | 1 |
| Emission control equipment obviously modified crankcase ventilation pipe on rocker cover emitting into atmosphere (8.2.1.1 (a)) | 1 |
| Rear Exhaust has a major leak of exhaust gases & centre (6.1.2 (a)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Offside Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced floor panel (7.1.1 (a) (i)) | 1 |
| Offside Inner Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings sill to floor |6.1.B.2| | 1 |
| Nearside Rear Suspension arm fractured weld on arm insufficient (5.3.3 (b) (ii)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened antiroll bar bracket weld insufficient (5.3.3 (b) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened antiroll bar bracket weld insufficient (5.3.3 (b) (i)) | 1 |
| Nearside Rear Direction indicator adversely affected by the operation of another lamp |4.4.3 |b|| | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp |4.4.3 |b|| | 1 |
| Offside Rear Upper Suspension arm pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases on rear box join (6.1.2 (a)) | 1 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
| Offside Rear Hydraulic fluid leaking excessively Brake fluid |8.4.1 |a| |i|| | 1 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Upper suspension arm mounting, spring mounting and antiroll bar mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Upper suspension arm mounting, spring mounting and antiroll bar mounting |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Upper suspension arm mounting, spring mounting and antiroll bar mounting |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Upper suspension arm mounting, spring mounting and antiroll bar mounting |5.3.6 |a| |ii|| | 1 |
| Nearside Headlamp insecure bolt broken |1.7.3| | 1 |
| Offside Headlamp insecure bolt broken |1.7.3| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits see sheet 0.71 % (8.2.1.2 (b)) | 1 |
| Offside Front Headlamp lens seriously defective headlamp unit has condensation (4.1.1 (b) (ii)) | 1 |
| Front Brake disc contaminated (1.1.14 (b)) | 1 |
| Nearside Front Wheel nut|s| loose |4.2.A.1e| | 1 |
| Centre Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Suspension rod fractured (5.3.3 (b) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded arch lower |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded centre floor to sill |5.2.6| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Rear reflector excessively deteriorated so that its function is impaired |1.5.1c| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked in yellow (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked in yellow (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension arm attachment bracket/mounting insecure lower ball joint bolt |5.3.3 |a| |i|| | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner corner pocket (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill front to mid of car (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch near shock mount |5.3.6 |a| |i|| | 1 |
| Offside Rear Anti-roll bar linkage missing (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded sill to arch area |5.2.6| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded sill to arch area |5.2.6| | 1 |
| Nearside Front Gas suspension unit deteriorated and likely to fail |2.4.D.1b| | 1 |
| Nearside Rear Body panel corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 1 |
| Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Numerous areas (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Numerous areas (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Numerous areas (7.1.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Drivers seat insecure BOLT MISSING (6.2.5 (a) (ii)) | 1 |
| Centre Rear Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front Upper Suspension component ball joint likely to become detached ball joint locking device missing |5.3.4 |a| |ii|| | 1 |
| Offside Rear Shock absorber insecure |2.7.2b| | 1 |
| Nearside Front Anti-roll bar insecurely attached DROP LINK (5.3.3 (a) (i)) | 1 |
| Offside Front Anti-roll bar insecurely attached DROP LINK (5.3.3 (a) (i)) | 1 |
| Offside Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner underside sill |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner underside sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Valve stem seriously damaged |5.2.3 |j|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor x 2 (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced SILL/FLOOR (6.1.1 (c) (i)) | 1 |
| Offside Rear Brake pipe excessively damaged (1.1.11 (c)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded chassis |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded rear inner sill |5.2.6| | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill corroded and holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill marked yellow (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill marked yellow (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Rear silencer (6.1.2 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded centre outer side sill holed & corroded |5.2.6| | 1 |
| Parking brake lever is impeded in its travel |3.1.6c| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Wheel arch - Chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Wheel arch - Chassis (6.1.1 (c) (i)) | 1 |
| Central Upper Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting n/s+o/s outer sills |6.2.2 |d| |i|| | 1 |
| Nearside Rear Anti-roll bar ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded SILL |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded SILL |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced INNER SILL /FLOOR (7.1.1 (a) (i)) | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced offside rear |2.4.G.1| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch and outer seal |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch and outer seal |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis holed |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced arch and sill (7.1.1 (a) (i)) | 1 |
| Nearside Steering locking device missing track rod (2.1.3 (d)) | 1 |
| Offside Steering locking device missing track rod (2.1.3 (d)) | 1 |
| Emissions not tested water pump belt missing |7.3.A.1| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Lower |7.1.1 |a| |i|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Lower |7.1.1 |a| |i|| | 1 |
| Subframe mounting prescribed area excessively corroded significantly reducing structural strength o/s front chassis leg |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded chassis |5.2.6| | 1 |
| Offside Front Body panel corroded and likely to cause injury wing |6.2.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded chassis floor |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS LEG ABOVE ROLL BAR MOUNTING |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS LEG ABOVE ROLL BAR MOUNTING |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL AND INNER ARCH AREAS (5.3.6 (a) (i)) | 1 |
| Power steering pipe|s| or hose|s| leaking |from rack to hose| |2.3.3b| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |wheel arch| |6.1.C.1| | 1 |
| Steering system fouling |steering rack gaitors fouling undertray| |2.2.D.2a| | 1 |
| Offside Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Anti-lock braking system component missing cable tied up on suspension arm (1.6 (e)) | 1 |
| Nearside Rear Brake cable has restricted free movement (1.1.15 (e)) | 1 |
| Offside Rear Brake cable has restricted free movement (1.1.15 (e)) | 1 |
| Power steering pump fractured and steering adversely affected (2.1.5 (d) (ii)) | 1 |
| Offside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill (7.1.1 (a) (i)) | 1 |
| Offside Brake pipe leaking on a hydraulic braking system Front to rear brake pipe |1.1.11 |b| |ii|| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings by suspension |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings by suspension |6.1.B.2| | 1 |
| Centre Exhaust has a major leak of exhaust gases box/pipe |7.1.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases box/pipe joint |7.1.2| | 1 |
| Offside Front Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Braking system leaking Banjo bolt / washers |3.6.A.1| | 1 |
| Offside Front Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength boot floor by subframe mounting (5.3.6 (a) (i)) | 1 |
| Emissions not tested excessive exhaust blow (8.2.1.2 (d)) | 1 |
| Nearside Rear Stop lamp(s) lens defective such that the emitted light is adversely affected (4.3.1 (b) (ii)) | 1 |
| Nearside Rear Stop lamp(s) emits other than a steady red light (4.3.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis rail/inner wing |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded Chassis rail |2.4.A.3| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded Wheel arch |5.2.6| | 1 |
| Nearside Front Front position lamp|s| not working side light inop |1.1.A.3b| | 1 |
| Offside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings chassis rail extensive damage torn away and crushed |6.1.B.2| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint link bar knocking |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint link bar knocking |2.4.G.2| | 1 |
| Offside Front Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Offside Rear Integral body structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Offside Rear Macpherson strut insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill/floor (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced inner sill (6.1.1 (d) (i)) | 1 |
| Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced inner sill (6.1.1 (d) (i)) | 1 |
| Nearside Parking brake inoperative on one side Cable detached during brake teat (1.4.1 (a)) | 1 |
| Offside Headlamp not working on dipped beam Comes on slowly sometimes (4.1.1 (a) (ii)) | 1 |
| Nearside Front Shock absorbers damaged to the extent that it does not function Lower spring seat excessively corroded (5.3.2 (b)) | 1 |
| Exhaust fumes entering cabin |6.1.2 |b| |i|| | 1 |
| Nearside Front Service brake excessively binding disc red in colour |1.2.1 |f|| | 1 |
| Offside Front Lower Suspension arm likely to become detached Ball joint bolt of wrong length, securing nut not fully securing bolt (5.3.3 (a) (ii)) | 1 |
| Offside Front Shock absorbers insecurely attached lower arm bracket broken needs new arm (5.3.2 (a) (i)) | 1 |
| Offside Front Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Nearside Rear Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Brake hose leaking on a hydraulic braking system leaking at calliper |1.1.12 |c| |ii|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced CHASSIS LEG (6.1.1 (c) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Suspension arm attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings REAR OF N/S SILL |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings REAR OF O/S SILL |6.1.B.2| | 1 |
| Front Position lamp not working both side (4.2.1 (a) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded FRONT |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded FRONT X2 |2.4.A.3| | 1 |
| Headlamp incorrect colour both |1.7.5b| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis rail above anti roll bar mount |2.4.A.3| | 1 |
| Rear Upper Stop lamp not working high level brake light |1.2.1b| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis antiroll bar mount area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis antiroll bar mount area (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Upper Suspension arm has excessive play in a pin/bush rear bush |2.4.G.2| | 1 |
| Offside Front Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill - two places (7.1.1 (a) (i)) | 1 |
| Centre Front Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floors to sills |6.1.B.2| | 1 |
| Nearside Lower Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Fuel cap/sealing device missing Cap missing (6.1.3 (b) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Lower sill X 2 |7.1.1 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect dirty glass |1.8.A.1b| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect dirty glass |1.8.A.1b| | 1 |
| Headlamp excessively deteriorated so that the light output is severely reduced Glass on both lamps affecting beam image |1.7.5a| | 1 |
| Valve stem seriously damaged N/S/F & Both rear valves split |4.1.D.1e| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill area (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both outer sills (5.3.6 (a) (i)) | 1 |
| Offside Rear Braking system leaking brake caliper. |3.6.A.1| | 1 |
| Offside Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Front Coil spring mounting corroded and seriously weakened |2.4.C.3c| | 1 |
| Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Underside of front chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg through wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed |7.1.1 |a| |i|| | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting out rigger (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting weld not approp (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure is deformed and structural rigidity is significantly reduced in side wheel arch (6.1.1 (a) (i)) | 1 |
| Offside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Braking system leaking Caliper area |3.6.A.1| | 1 |
| Nearside Headlamp not working on dipped beam Bad connection at back of headlamp |1.7.5a| | 1 |
| Braking system leaking front to rear |3.6.A.1| | 1 |
| Rear Brake performance not tested due to fluid leak |3.7.A.1| | 1 |
| Front Body component damaged and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Brake hydraulic reservoir leaking hydraulic fluid |3.6.A.1| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings underneath |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Rear outer sill area corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Rear outer sill area corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Tie bar/rod ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt drop link |2.4.G.2| | 1 |
| Offside Rear Tie bar/rod ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt drop link |2.4.G.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |6.1.A.1| | 1 |
| Nearside Front Vehicle structure has an inadequate repair which adversely affects braking or steering taped over corrosion |6.1.A.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |inside wheel arch| |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |inside wheel arch| |6.1.B.2| | 1 |
| Rear Anti-roll bar missing |5.3.3 |a| |ii|| | 1 |
| Nearside Rear Anti-roll bar linkage missing |5.3.3 |a| |ii|| | 1 |
| Offside Rear Anti-roll bar linkage missing |5.3.3 |a| |ii|| | 1 |
| Nearside Front Inner Subframe mounting prescribed area is excessively corroded Wing |2.4.A.3| | 1 |
| Offside Rear Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Chassis |2.4.A.3| | 1 |
| Offside Seat belt obviously repaired |5.2.2c| | 1 |
| Inner Obligatory mirror does not provide a view to the rear |8.1.2b| | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rear quarter of side sill (6.2.2 (d) (i)) | 1 |
| Offside Front Power steering component leaking leak at rack |2.1.5 |a|| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill split on old welding |6.1.B.2| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases joint blowing |7.1.2| | 1 |
| Offside Rear front brake juddering severely |3.7.A.2b| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer Sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Anti roll bar mtg |2.4.A.3| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting likely to become detached bolts loose (5.3.3 (a) (ii)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected lens broken (4.5.1 (b) (ii)) | 1 |
| Offside Front Anti-lock braking system component excessively damaged |3.4.2| | 1 |
| Front Anti-roll bar linkage fractured both (5.3.3 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wing above top arm (5.3.6 (a) (ii)) | 1 |
| Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering CHASSIS LEG SUBFRAME MOUNTING (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering CHASSIS LEG SUBFRAME MOUNTINGS (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER WING / CHASSIS LEG (6.1.1 (c) (i)) | 1 |
| Emissions not tested due to major exhaust blow |8.2.1.2 |d|| | 1 |
| Front Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Emissions not tested exhaust blow |8.2.1.2 |d|| | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill |6.2.2 |d| |ii|| | 1 |
| Suspension component mounting prescribed area is excessively corroded offside front inner wing |2.4.A.3| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits CO fluctuating in and out side limit (8.2.1.2 (c)) | 1 |
| Offside Rear Upper coil spring incomplete |2.4.C.1a| | 1 |
| Exhaust has a major leak of exhaust gases tail box joint (6.1.2 (a)) | 1 |
| Nearside Front Suspension component likely to become detached top mount nuts missing (5.3.3 (a) (ii)) | 1 |
| Offside Front Suspension component likely to become detached top mount nuts missing (5.3.3 (a) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor corroded and holed near front seat mounting. |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor corroded and holed near front seat mounting. |7.1.1 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases Exhaust corroded and holed at rear. |6.1.2 |a|| | 1 |
| Emissions not tested Battery charging failure during emission test |7.3.A.1| | 1 |
| Nearside Front Body has a sharp edge caused by damage wing mirror body |6.1.C.1| | 1 |
| Nearside Rear Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength holes and marked in yellow (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength holes and marked in yellow (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Offside front `A` pillar by door opening |5.3.6 |a| |i|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Nearside front `A` pillar by door opening |5.3.6 |a| |i|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Nearside rear inner sill area |5.3.6 |a| |i|| | 1 |
| Offside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Emissions not tested SERIOUS MISFIRE PRESENT (8.2.1.2 (d)) | 1 |
| Offside Headlamp light intensity severely reduced poor connection on headlamp plug cleaned terminal |4.1.4 |a|| | 1 |
| Rear Road wheel more than one fixing missing both sides (5.2.1 (a) (ii)) | 1 |
| Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits above |8.2.1.2 |c|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner wing |6.1.1 |c| |ii|| | 1 |
| Brake performance not tested due to pedal being very soft and offside caliper sized (1.2.1 (g)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front position lamp|s| not working side light |1.1.A.3b| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak rear silencer leaking /corroded (8.2.1.1 (b)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits 220 (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 8.49% (8.2.1.2 (b)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.049% (8.2.1.2 (c)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits 0.76% (8.2.1.2 (b)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor pan |6.2.2 |d| |i|| | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases leaking at joint |7.1.2| | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed and corroded |7.1.1 |a| |i|| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed and corroded |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis by anti roll bar /subframe mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering inner arch |6.1.A.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outter sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Arch (7.1.1 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill |6.1.1 |c| |i|| | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill |6.1.1 |c| |i|| | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill |6.1.1 |c| |i|| | 1 |
| Exhaust has a major leak of exhaust gases Backbox |7.1.2| | 1 |
| Nearside Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Offside Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Anti-roll bar linkage synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |6.1.A.1| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear outer sill section (6.1.1 (c) (i)) | 1 |
| Nearside Front Brake disc contaminated (1.1.14 (b)) | 1 |
| Offside Rear Brake disc contaminated (1.1.14 (b)) | 1 |
| Exhaust has a major leak of exhaust gases rear join to rear silencer |7.1.2| | 1 |
| Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis under wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded through to excess (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded through to excess (7.1.1 (a) (i)) | 1 |
| Offside Front Tie bar/rod worn and seriously weakened |2.4.G.1| | 1 |
| Offside Side repeater adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Nearside brake disc excessively scored |3.5.1h| | 1 |
| Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced BOTH FRONT |4.1.4 |b|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak Rear Exhaust |8.2.1.1 |b|| | 1 |
| Front passenger door catch insecure |6.2.B.2| | 1 |
| Offside Seat belt anchorage prescribed area is severely distorted |5.2.6| | 1 |
| Rear Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Outer Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases joint corroded away |7.1.2| | 1 |
| Nearside Rear Lower Anti-roll bar attachment bracket/mounting insecure nut loose |2.4.G.1| | 1 |
| Nearside Front Inner Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced door sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced door sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Corrosion hole in sil |6.1.1 |c| |i|| | 1 |
| Offside Outer Integral body structure is fractured and structural rigidity is significantly reduced sill (6.1.1 (a) (i)) | 1 |
| Hydraulic fluid leaking excessively steering rack area |8.4.1 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases at backbox |7.1.2| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive reading 0.70 |7.3.D.3| | 1 |
| Offside Front Upper Suspension arm ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Outer Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis heavily corroded (5.3.6 (a) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Direction indicator incomplete |1.5.A1b| | 1 |
| Rear Sub-frame insecure |2.4.G.1| | 1 |
| Headlamp excessively deteriorated so that the light output is severely reduced both front |1.7.5a| | 1 |
| Front Headlamp excessively deteriorated so that the light output is severely reduced both |1.7.5a| | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill panel (6.1.1 (c) (i)) | 1 |
| Nearside Rear Hydraulic brake calliper damaged |1.1.16 |a| |i|| | 1 |
| Offside Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Suspension arm inappropriately repaired |2.4.A.2| | 1 |
| Nearside Rear Braking system leaking at caliper |3.6.A.1| | 1 |
| Nearside Front suspension has a suspension lower ball joint securing nut not locked |2.5.B.1a| | 1 |
| Electrical wiring insecure and in contact with sharp edges OXYGEN SENSOR WIRING (4.11 (a) (ii)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear of wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear of wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill floor |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system floor pan (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Fuel cap/sealing device mounting flange/sealing method defective |7.2.4c| | 1 |
| Offside Rear Brake pipe excessively damaged to flexi (1.1.11 (c)) | 1 |
| Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Lower Suspension component ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Exhaust emissions - engine idle speed too high o2 (8.2.1.2 (e)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits high .51 should be .20 |8.2.1.2 |b|| | 1 |
| Nearside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings insufficient weld |6.1.B.2| | 1 |
| Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings insuficient weld |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings insufficient weld |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings insufficient weld |6.1.B.2| | 1 |
| Offside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear Upper Radius arm corroded and seriously weakened wishbone |2.4.G.1| | 1 |
| Nearside Headlamp aim beam image obviously incorrect no image |1.8.A.1b| | 1 |
| Rear Fuel hose leaking |7.2.3| | 1 |
| Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x2 (5.3.6 (a) (i)) | 1 |
| Nearside Power steering pipe/hose leaking |2.1.5 |a|| | 1 |
| Central Stop lamp not working fitted in boot lid |1.2.1b| | 1 |
| Nearside Rear Anti-roll bar linkage insecurely attached droplink (5.3.3 (a) (i)) | 1 |
| Offside Rear Brake pipe leaking front to rear pipe |3.6.A.1| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect bulb retaining device missing |1.8.A.1b| | 1 |
| Front Headlamp does not operate immediately when selected on main beam |1.7.4a| | 1 |
| Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Shock absorber has negligible damping effect |2.7.5| | 1 |
| Anti-roll bar linkage corroded and seriously weakened |2.4.G.1| | 1 |
| Exhaust has a major leak of exhaust gases Rear silencer flange detiorated |7.1.2| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded rear of inner sill |5.2.6| | 1 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Front Headlamp not working on dipped beam both |4.1.1 |a| |ii|| | 1 |
| Front Headlamp not working on main beam both |4.1.1 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at subframe mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside wheelarch. located above upper suspension arm. marked. (5.3.6 (a) (i)) | 1 |
| Headlamp lens seriously defective both headlamps deteriorated. (4.1.1 (b) (ii)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill and floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill and floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced rear wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced rear wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill and floor (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill and floor (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Battery insecure and likely to fall from carrier hole in boot floor (4.13 (a) (ii)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced AND OUTER SILLS |7.1.1 |a| |i|| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced AND OUTER SILLS |7.1.1 |a| |i|| | 1 |
| Rear Engine mounting damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Back box |7.1.2| | 1 |
| Nearside Front Headlamp aim not tested no beam pattern (4.1.2 (b)) | 1 |
| Offside Front Headlamp aim not tested no beam pattern (4.1.2 (b)) | 1 |
| Stop lamp remains on when the brakes are released | 1 |
| Nearside Front Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Seat belt buckle not functioning as intended seat belt rajetplayimg up |7.1.2 |d|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength closing panel in wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength closing panel in wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering subframe mounting/ chassis rail |6.1.A.1| | 1 |
| Offside Front Electrical wiring insecure footwell |1.9.2a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail near to anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing (6.1.1 (c) (i)) | 1 |
| Nearside Side repeater incorrect colour |4.4.3 |a|| | 1 |
| Offside Side repeater incorrect colour |4.4.3 |a|| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases tailpipe joint |7.1.2| | 1 |
| Nearside Front Lower Steering linkage ball joint ball joint dust cover missing split pin missing |2.1.3 |g| |ii|| | 1 |
| Offside Front Upper Steering linkage ball joint ball joint dust cover missing split pin missing |2.1.3 |g| |ii|| | 1 |
| Nearside Front Brake hose excessively stretched |1.1.12 |b| |ii|| | 1 |
| Offside Front Brake hose excessively stretched |1.1.12 |b| |ii|| | 1 |
| Emissions not tested emission conditions not met |8.2.1.2 |d|| | 1 |
| Nearside Rear Outer Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear brake disc cracked |3.5.1h| | 1 |
| Offside Rear brake disc cracked |3.5.1h| | 1 |
| Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Offside Front Upper Coil spring insecure (5.3.1 (a) (i)) | 1 |
| Rear Axle insecure (5.1.1 (b) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill front & Outer sill rear (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Rear outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam DONE |1.7.5a| | 1 |
| Offside Front Headlamp not working on dipped beam DONE |1.7.5a| | 1 |
| Centre Parking brake lever has no reserve travel to rear |DONE| |3.1.6b| | 1 |
| Nearside Front Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| Offside Front Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Nearside Rear Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Nearside Rear Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Front Wheel bolt|s| missing |4.2.A.1e| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/floor (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced along inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced center floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Brake pipe at imminent risk of failure or fracture brake pipe across rear subframe to nearside brake hose corroded |leaks under pressure |1.1.11 |a|| | 1 |
| Offside Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassiss |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassiss |2.4.A.3| | 1 |
| Front Service brake excessively binding unable to check wheel bearings both front brakes binding (1.2.1 (f)) | 1 |
| Offside Rear All direction indicators adversely affected by the operation of another lamp operates as fog light switch and fog is indicator (4.4.3 (b)) | 1 |
| Offside Rear Upper Suspension arm pin or bush excessively worn outer |5.3.4 |a| |i|| | 1 |
| Offside Front Front position lamp|s| obviously incorrectly positioned |1.1.A.3a| | 1 |
| Hazard warning switch missing |1.4.B.1d| | 1 |
| Outer Rear Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill + inner wing (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Suspension arm ball joint likely to become detached Nut insecure |5.3.4 |a| |ii|| | 1 |
| Offside Front Upper Suspension arm ball joint likely to become detached Nut insecure |5.3.4 |a| |ii|| | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached Locking device inoperative due to bolt length |5.3.4 |a| |ii|| | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached Locking device inoperative due to bolt length |5.3.4 |a| |ii|| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis/Suspension arm mount (6.1.1 (c) (i)) | 1 |
| Fuel system component leaking excessively or a risk of fire |6.1.3 |b| |ii|| | 1 |
| Position lamp not working front and rear (4.2.1 (a) (ii)) | 1 |
| Front Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Nearside Rear Suspension arm insecure |2.4.G.1| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt split (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-lock braking system component inappropriately repaired |3.4.4| | 1 |
| Brake back plate|s| securing device loose missing |3.5.1j| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch chassis |2.4.A.3| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion arch area |6.1.C.1| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings offside floor |6.1.B.2| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded Chassis member |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded Chassis member |2.4.A.3| | 1 |
| brake disc in such a condition that it is seriously weakened Both rear |3.5.1i| | 1 |
| Nearside Outer Rear Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer skin holed |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer skin holed |5.2.6| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (chassis) (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (chassis) (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (under repair panel and end of sill) (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is inadequately repaired sill repair panel (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Anti-roll bar linkage ball joint likely to become detached Broken. (5.3.4 (a) (ii)) | 1 |
| Fuel cap/sealing device ineffective temp fuel cap seal perished (6.1.3 (b) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Rear fog lamp not working can not find switch (4.5.1 (a) (ii)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill multiple holes (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure is fractured and structural rigidity is significantly reduced inner wheel arch at front (6.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected of sill panel (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected of sill panel (5.3.6 (a) (ii)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded Off side outer sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded Off side sill to floor |5.2.6| | 1 |
| Suspension component mounting prescribed area is excessively corroded Off side front inner wing / chassis leg |2.4.A.3| | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength boot floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg under wheel arch |6.1.A.1| | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both front (4.1.4 (b)) | 1 |
| Rear Exhaust has a major leak of exhaust gases exhaust flange joint (6.1.2 (a)) | 1 |
| Offside Front Lower Front suspension has a suspension lower ball joint securing nut not locked |2.5.B.1a| | 1 |
| Centre Rear Exhaust has a major leak of exhaust gases silancer joint |7.1.2| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner floor |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor holed |7.1.1 |a| |i|| | 1 |
| Nearside Front Upper Suspension arm pin or bush likely to become detached |5.3.4 |a| |ii|| | 1 |
| Headlamp insecure offside |1.7.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis area (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chasis (5.3.6 (a) (i)) | 1 |
| Shock absorber has an excessively worn bush n/s strut bottom mounting bush |2.7.4| | 1 |
| Shock absorber has an excessively worn bush o/s strut bottom mounting bush |2.7.4| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front chassis section from bumper mounting back to suspenion mounting corroded |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis section from bumper mounting baxck to suspension mounting |6.1.1 |c| |i|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength n/s and o/s front suspension mouinting area at chassis sections corroded |5.3.6 |a| |i|| | 1 |
| Nearside Headlamp not working on dipped beam both head light aims too low and incorrect | could be due to head light lens age deteriorated | |4.1.1 |a| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rear arch (7.1.1 (a) (i)) | 1 |
| Brake disc significantly and obviously worn front and rear (1.1.14 (a) (i)) | 1 |
| Coil spring fractured or broken both front (5.3.1 (b) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired under wing (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits CO too high (8.2.1.2 (b)) | 1 |
| Offside Front Vehicle structure has excessive damage seriously affecting its strength within 30cm of a towbar mounting inner sill (6.1.6 (i) (i)) | 1 |
| Inner Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area |6.1.B.2| | 1 |
| Nearside Rear Body has a projection caused by damage Bumper |6.1.C.1| | 1 |
| Exhaust has a major leak of exhaust gases Back box missing |7.1.2| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer/inner sill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Upper Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rear section of the sill heavily corroded |6.2.2 |d| |i|| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rear section of the sill heavily corroded |6.2.2 |d| |i|| | 1 |
| Nearside Rear Brake hose twisted |3.6.B.4c| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded and within anti roll bar mounting bracket |2.4.A.3| | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill panel (6.1.1 (c) (i)) | 1 |
| Anti-roll bar linkage pin or bush likely to become detached already adrift at lower end (5.3.4 (a) (ii)) | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded centre floor pan to outer sill |5.2.6| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill end |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Outersill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis behind wheel |2.4.A.3| | 1 |
| Front Valve stem seriously damaged both front (5.2.3 (j)) | 1 |
| Rear Valve stem seriously damaged both rear (5.2.3 (j)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Subframe mounting (5.3.6 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Anti roll bar mounting (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Lower Suspension rod insecurely attached bolt broken |5.3.3 |a| |i|| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt d/link top and bottom |2.4.G.2| | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Offside Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced center inner sill |6.1.1 |c| |i|| | 1 |
| Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
| Nearside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti rollbar mount |5.3.6 |a| |i|| | 1 |
| Nearside Inner Front Lower Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Nearside Rear Upper Suspension arm pin or bush excessively worn outer (5.3.4 (a) (i)) | 1 |
| Service brake excessively fluctuating front (1.2.1 (e)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill within 30cm of seat belt mounting (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded in sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded in sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded in wheel arch |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outersill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Rear position lamp|s| incorrect colour light lens cracked |1.1.A.3e| | 1 |
| Sub-frame attachment bracket/mounting bolt missing support bar bolt missing |2.4.G.1| | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Rear Drive shaft uj which forms part of the suspension has a missing flange bolt |2.4.G.4c| | 1 |
| Offside Front Anti-roll bar has excessive play in a ball joint snapped
|2.4.G.2| | 1 |
| Offside Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Emissions not tested overheated (8.2.1.2 (d)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect bulb fitted incorrectly |4.1.2 |c|| | 1 |
| Nearside Headlamp not working on main beam intermittant. |1.7.5a| | 1 |
| Nearside Headlamp adversely affected by the operation of another lamp goes out when main beam operated.intermittant |1.7.5c| | 1 |
| Centre Upper Stop lamp not working 1x 382 bulb. |1.2.1b| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced hole in outa seal |7.1.1 |a| |i|| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive 4.5% |7.3.D.3| | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded both outer sills |2.4.A.3| | 1 |
| Body panel insecure bonnet |6.2.1 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 1 |
| Offside Front Front suspension has a suspension upper ball joint securing nut loose track rod end |2.5.B.1a| | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wing (6.1.1 (c) (i)) | 1 |
| Suspension component mounting prescribed area is excessively corroded both outer rear seals |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near anti roll bar (5.3.6 (a) (i)) | 1 |
| Nearside Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill holed (6.2.2 (d) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg holed (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear pipe join (6.1.2 (a)) | 1 |
| Front Service brake excessively binding Brakes (1.2.1 (f)) | 1 |
| Brake fluid contaminated Due to standing (1.8 (a)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor sill (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering wheel arch |6.1.A.1| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering wheel arch |6.1.A.1| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Body mount/boot floor edge (6.1.1 (c) (i)) | 1 |
| Central Exhaust system insecure clamps missing (6.1.2 (a)) | 1 |
| Offside Rear Body has a sharp edge caused by corrosion WHEEL ARCH. |6.1.C.1| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits EXHAUST LEAK SUSPECTED CAUSE < back box to middle pipe joint. |7.3.D.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced lower sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Nearside Rear Braking system leaking Brake caliper leaking |3.6.A.1| | 1 |
| Offside Front Upper Suspension arm insecurely attached ball joint (5.3.3 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn front bush |5.3.4 |a| |i|| | 1 |
| Offside Front Lower Suspension arm has an unsafe modification non original bolt is not long enough, nut not held on with enough threads. |5.3.3 |c| |i|| | 1 |
| Offside Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Front Front position lamp|s| not working both bulbs |1.1.A.3b| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill. (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill. (6.1.1 (c) (i)) | 1 |
| Suspension component mounting prescribed area is excessively corroded both front inner wing panels corroded both rear sills o/s r/under sill corroded |2.4.A.3| | 1 |
| Nearside Front Sub-frame corroded and seriously weakened chassis |2.4.G.1| | 1 |
| Offside Front Floor excessively deteriorated floor to sill |6.2.4 |a| |i|| | 1 |
| Emissions not tested engine temp too high (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Rear Braking system leaking brake fluid leaking from underside during brake test... test aborted |3.6.A.1| | 1 |
| Power steering pipe|s| or hose|s| leaking Rack feed pipes |2.3.3b| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Excessive corrosion at the sill (7.1.1 (a) (i)) | 1 |
| Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Excessive Corrosion at the sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Front Headlamp insecure |4.1.1 |c|| | 1 |
| Rear Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Rear fog lamp obviously incorrectly positioned fog light fitting fitted in o/s indicator position |1.3.2a| | 1 |
| Offside Rear Direction indicator obviously incorrectly positioned fitted in fog light position |1.4.A.2b| | 1 |
| Brake lever has insufficient reserve travel hand brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Exhaust has a major leak of exhaust gases REAR SILENCER TAIL PIPE |7.1.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings CHASSIS AT SUB / FRAME / ANTI ROLL BAR MOUNTS HOLED AND CORRODED |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER AND OUTER SILLS HOLED AND CORRODED |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings CHASSIS HOLED AT FUEL AND BRAKE PIPES |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mounting |2.4.A.3| | 1 |
| Braking system leaking Offside rear caliper |3.6.A.1| | 1 |
| Offside Parking brake inoperative on one side also very poor nearside (1.4.1 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Front Shock absorber detached |2.7.2b| | 1 |
| Nearside Front Lower Suspension arm fractured |2.4.G.1| | 1 |
| Offside Front Lower Suspension arm fractured |2.4.G.1| | 1 |
| Offside Rear Lower Suspension arm fractured |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing/chassis |2.4.A.3| | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced lower sill and floor area corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced seat belt mounting areas weakened by corrosion (7.1.1 (a) (i)) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting inner wing (6.2.2 (d) (i)) | 1 |
| Nearside Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting inner sill corroded front and rear (6.2.2 (d) (i)) | 1 |
| Offside Rear Anti-roll bar ball joint likely to become detached detached (5.3.4 (a) (ii)) | 1 |
| Anti-roll bar insecure |2.4.G.1| | 1 |
| Nearside Lower Front suspension has a suspension lower ball joint securing nut not locked |2.5.B.1a| | 1 |
| Offside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings osf |6.1.B.2| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings nsf inners |6.1.B.2| | 1 |
| Power steering pipe/hose excessively damaged power steering pipe leaking nearside of engine |2.1.5 |g| |i|| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering badly corroded at offside front anti roll bar fixing point |6.1.1 |c| |ii|| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Wing Arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis |6.2.2 |d| |i|| | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis |6.2.2 |d| |i|| | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wing (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis Rail Hole (5.3.6 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill Hole (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg as marked (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sile (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch marked with yellow chalk (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front of chassis leg marked with yellow chalk (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
| Front brake disc cracked |3.5.1h| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 1 |
| Front Exhaust has a major leak of exhaust gases front joint (6.1.2 (a)) | 1 |
| Emissions unable to be completed overheating (8.2.2.2 (e)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis - anti roll bar mounting |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis - anti roll bar mounting |2.4.A.3| | 1 |
| Offside Front Road wheel fixing missing wheel nut |5.2.1 |a| |i|| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Stop lamp adversely affected by the operation of another lamp high level |1.2.1f| | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired above antiroll bar mounting (6.2.2 (d) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer wheel arch (7.1.1 (a) (i)) | 1 |
| Power steering pipe/hose corroded such that the steering is adversely affected (2.1.5 (g) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected outer sill holes 30cm seat belt mounting (5.3.6 (a) (ii)) | 1 |
| Nearside Outer Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Inner Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor pan in front of back wheel |6.1.B.2| | 1 |
| Offside Rear Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Emissions not tested Due to exhaust leak |8.2.1.2 |d|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner arch |2.4.A.3| | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system across axle (1.1.11 (b) (ii)) | 1 |
| Nearside Front Brake hose excessively stretched Pipe stretched wen performing lock to lock (1.1.12 (b) (ii)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users coolant pipe leaking |8.4.1 |a| |i|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded front chassis roll bar mounting |2.4.A.3| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 1 |
| Offside Rear Body component corroded and likely to cause injury arch |6.2.1 |a| |i|| | 1 |
| Offside Outer Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill |6.2.2 |d| |ii|| | 1 |
| Nearside Track rod end seriously misaligned (2.1.3 (e)) | 1 |
| Offside Track rod end seriously misaligned (2.1.3 (e)) | 1 |
| Offside Front Electrical wiring insulation in such a condition there is an imminent risk of fire or formation of sparks headlight wiring (4.11 (c) (iii)) | 1 |
| Nearside Front Front position lamp|s| not working headlight |1.1.A.3b| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush drop link |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded front strut |2.4.A.3| | 1 |
| Nearside Front Coil spring insecure spring too short. after jacking up vehicle the spring does not correctly locate when the suspension is returned to its normal running position (5.3.1 (a) (i)) | 1 |
| Offside Front Coil spring with an unsafe modification top spring mounting missing (5.3.1 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases joint before rear silencer (6.1.2 (a)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits 0.63% (8.2.1.2 (b)) | 1 |
| Nearside Front Road wheel badly distorted inner part of rim (5.2.2 (c) (i)) | 1 |
| Offside Front Coil spring insecure spring too short. after jacking up vehicle the spring does not correctly locate when the suspension is returned to its normal running position (5.3.1 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 1.62% (8.2.1.2 (b)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre pipe joint at rear silencer (6.1.2 (a)) | 1 |
| Emissions not tested due to excess high readings on co and engine overheating |7.3.A.1| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor, adjacent to Sill perforated (7.1.1 (a) (i)) | 1 |
| Offside Headlamp not working on main beam front o/s headlamp not working (4.1.1 (a) (ii)) | 1 |
| Offside Rear Service brake excessively binding rear o/s brake binding (1.2.1 (f)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill and wheel arch area. |5.2.6| | 1 |
| Nearside Front Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill x2 areas marked with chalk (7.1.1 (a) (i)) | 1 |
| Nearside Rear Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 1 |
| Valve stem seriously damaged All four |4.1.D.1e| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner back wheel arch |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner back wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded outer chassis |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded lower sill |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |outer sill area | |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |outer sill area| |5.2.6| | 1 |
| Centre Front Body has a sharp edge caused by damage Number plate frame |6.1.C.1| | 1 |
| Nearside Rear Fuel cap/sealing device missing |7.2.4a| | 1 |
| Nearside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced centre outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Headlamps matched pair are not the same colour |1.7.6| | 1 |
| Exhaust has a major leak of exhaust gases rear box blowing |7.1.2| | 1 |
| Front Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Front Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Upper Suspension component has an unsafe modification split pin missing |5.3.3 |c| |i|| | 1 |
| Nearside Front Lower Suspension component has an unsafe modification split pin missing |5.3.3 |c| |i|| | 1 |
| Offside Front Upper Suspension component has an unsafe modification split pin missing |5.3.3 |c| |i|| | 1 |
| Offside Front Lower Suspension component has an unsafe modification split pin missing |5.3.3 |c| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill
|5.2.6| | 1 |
| Front Hydraulic fluid leaking continuously posing a serious risk to road safety power steering pipe |8.4.1 |a| |ii|| | 1 |
| Power steering inoperative Fluid leaking |2.3.3a| | 1 |
| Parking brake inoperative on one side n/s + o/s (1.4.1 (a)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner and outer sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded syspension top arm |2.4.A.3| | 1 |
| Nearside Front position lamp|s| not working & offside |1.1.A.3b| | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid calliper |3.6.A.1| | 1 |
| Nearside Front Anti-roll bar linkage attachment bracket/mounting fractured drop link snapped (5.3.3 (b) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded through inside wheel arch by sub frame (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded through inside wheel arch by sub frame (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension rod ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded Inner arch |2.4.A.3| | 1 |
| Nearside Rear Outer Brake lining|s| insecure |3.5.1g| | 1 |
| Rear front brake binding |3.7.B.1| | 1 |
| rear brake recording little or no effort both parking |3.7.B.5a| | 1 |
| Nearside Outer Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis box section holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill panels |7.1.1 |a| |i|| | 1 |
| Emissions not tested Due to rough running. (8.2.1.2 (d)) | 1 |
| Offside Rear Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner arch /chassis leg |2.4.A.3| | 1 |
| Central Exhaust has a major leak of exhaust gases clamps rusted out |7.1.2| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill to floor (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill to floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded sill/floor |5.2.6| | 1 |
| Offside Front Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Nearside Front Macpherson strut corroded and seriously weakened spring base |5.3.3 |b| |i|| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill |6.1.B.2| | 1 |
| Brake performance not tested calliper leaking |1.2.1 |g|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced chassis floor rail (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Rear exhaust silencer. (6.1.2 (a)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure Attachment on link rod. (5.3.3 (a) (i)) | 1 |
| Emissions unable to be completed Due to major blow of exhaust gases. No reading would be given. (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill excessively corroded. (7.1.1 (a) (i)) | 1 |
| Offside Rear Braking system leaking brake pipe |3.6.A.1| | 1 |
| Rear Direction indicator incorrect colour both white (4.4.3 (a)) | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened same (5.3.3 (b) (i)) | 1 |
| Exhaust has a major leak of exhaust gases cat missing (6.1.2 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced lower inner sill (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed cat cut out (8.2.1.2 (d)) | 1 |
| Exhaust has a major leak of exhaust gases rear to center corroded away |7.1.2| | 1 |
| Nearside Front Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Macpherson strut corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Rear Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment no reserve travel at lever (1.1.6 (c)) | 1 |
| Headlamp levelling device cannot be operated from the drivers seat (4.1.5 (b)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chasiss leg |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill section at rear |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired sill area not continually welded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Upper Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Inner Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded of outer sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded of outer sill |5.2.6| | 1 |
| Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Centre Electrical wiring inadequately supported |1.9.2a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassi rail (5.3.6 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/floor (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded nsr outer sill end and into wheel arch area |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is severely distorted sill area corroded |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases centre / rear exhaust joint area ....corroded badly also |7.1.2| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure bolt missing out of bracket (5.3.3 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced back of sill (7.1.1 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded rear sill |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded rear sill |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail inner arch |2.4.A.3| | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired BOTH INNER AND OUTER SILL HOLED AND CORRODED (6.2.2 (d) (ii)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired BOTH INNER AND OUT SILL HOLED AND CORRODED (6.2.2 (d) (ii)) | 1 |
| Front Headlamp light intensity severely reduced BOTH DEFFUSED PATTON (4.1.4 (a)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt ALSO PLAY IN IT (5.3.4 (b) (ii)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits TRIED 3 TIMES (8.2.1.2 (a)) | 1 |
| Nearside Rear Braking system leaking brake caliper (1.1.3 (d)) | 1 |
| Headlamp lens seriously defective dull (4.1.1 (b) (ii)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor pan (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting battery tray (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure has excessive corrosion which adversely affects braking or steering chasis |6.1.1 |c| |ii|| | 1 |
| Nearside Front Dipswitch does not operate immediately when selected on main beam |4.1.3 |b|| | 1 |
| Emissions not tested due to exhaust (8.2.1.2 (d)) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner wheel arch area holed / close to subframe mounts |6.1.B.2| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wing at anti roll bar mount |2.4.A.3| | 1 |
| Rear Exhaust system not adequately supported mount |7.1.1| | 1 |
| Nearside Outer Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front position lamp|s| not working sidelight |1.1.A.3b| | 1 |
| Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings @ headlight |6.1.B.2| | 1 |
| Offside Body has a projection caused by corrosion inner sill |6.1.C.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings @ strut |6.1.B.2| | 1 |
| Nearside Rear Upper Radius arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting both sides, front wheel arches (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension arm damaged and seriously weakened arm been cut (5.3.3 (b) (i)) | 1 |
| Seat belt likely to become detached in the event of a collision not attached (7.1.1 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced flloor to sill panel |7.1.1 |a| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill panel |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill panel |7.1.1 |a| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength & offside (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corrosion |7.1.1 |a| |i|| | 1 |
| Front position lamp|s| not working Both |1.1.A.3b| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced both inner arches (6.1.1 (c) (i)) | 1 |
| Nearside Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
| Nearside Front Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings outer chassis below inner wing |6.1.B.2| | 1 |
| Central Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Integral body structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (under sill covers) (6.1.1 (c) (i)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (under sill covers) (6.1.1 (c) (i)) | 1 |
| Drivers view of an obligatory external mirror significantly affected by an obstruction (3.1 (a) (ii)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Horn control insecure |1.6.1| | 1 |
| Offside Front Brake hose leaking |3.6.A.1| | 1 |
| Offside Rear Exhaust mounting missing |7.1.1b| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill and outer sill |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.11 |8.2.1.2 |c|| | 1 |
| Front Position lamp showing red light to the front |4.2.3 |a| |ii|| | 1 |
| Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.44 |8.2.1.2 |b|| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.40 |8.2.1.2 |c|| | 1 |
| Nearside Rear Parking brake inoperative on one side low effort |1.4.1 |a|| | 1 |
| Offside Rear Parking brake inoperative on one side inoperative |1.4.1 |a|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis near anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis member, by anti roll bar mounting point (5.3.6 (a) (i)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced o/s and n/s centre chassis members (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced near subframe |6.1.1 |c| |i|| | 1 |
| Nearside Rear front brakes release unevenly |3.7.B.4| | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting bolt missing Rear frame lower brace bar |2.4.G.1| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Anti-roll bar insecurely attached ALL FOUR LINKS (5.3.3 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases 2 major leaks (6.1.2 (a)) | 1 |
| Nearside Front Power steering pipe/hose leaking rack area (2.1.5 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre chassis (7.1.1 (a) (i)) | 1 |
| Offside Driver`s seat fore and aft adjustment mechanism not functioning as intended. |6.2.5 |b| |i|| | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction sun sticker too low and swept area of wipers (3.1 (a) (ii)) | 1 |
| Offside Front Headlamp incorrect colour (4.1.4 (a)) | 1 |
| Emissions not tested due to overheating (8.2.1.2 (d)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis holed |6.1.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mount |2.4.A.3| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded anti roll bar mount |2.4.A.3| | 1 |
| Offside Rear Tie bar/rod attachment bracket/mounting nut missing |2.4.G.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill / floor area (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill/Floor (6.2.2 (d) (i)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Service brake excessively binding 34kg/f (1.2.1 (f)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 1 |
| Nearside Front Inner Suspension spring mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Floor area. |5.2.6| | 1 |
| Nearside Front Outer Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill corroded (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill corroded (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed Exhaust pipe missing (8.2.1.2 (d)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail marked in yellow, hole 1 (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail marked in yellow, hole 2 (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced small hole, inside edge of chassis marked in yellow (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis, small hole near brake pipe mounting marked in yellow (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail marked in yellow (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch marked in yellow (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill marked in yellow (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Jacking point/Rear of sill!!! marked with chalk. (6.1.1 (c) (i)) | 1 |
| Front Service brake excessively fluctuating both (1.2.1 (e)) | 1 |
| Offside Rear Suspension component likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis/inner arch |2.4.A.3| | 1 |
| Nearside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Rear Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Body has a sharp edge caused by corrosion floor to sill |6.1.C.1| | 1 |
| Nearside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected outer sill |5.3.6 |a| |ii|| | 1 |
| Offside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected outer sill |5.3.6 |a| |ii|| | 1 |
| Offside Rear Battery insecure in the boot |1.9.1| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded floor/sill |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded chassis near seat mount |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded floor/sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded floor/outer sill |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering floor |6.1.A.1| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced at outer sill area (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper wishbone area |area marked with yellow paint| |5.3.6 |a| |i|| | 1 |
| Nearside Front Brake pipe likely to become detached or damaged hose |1.1.11 |d| |ii|| | 1 |
| Offside Front Brake pipe likely to become detached or damaged hose |1.1.11 |d| |ii|| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chaissis |6.2.2 |d| |i|| | 1 |
| Nearside Integral body structure is deformed and structural rigidity is significantly reduced chaissis and warn thin |6.1.1 |a| |i|| | 1 |
| Offside Integral body structure is deformed and structural rigidity is significantly reduced chaissis and warn thin |6.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Rear outer sill panel area |5.2.6| | 1 |
| Nearside Front Anti-roll bar linkage insecure and impairing directional stability not attached on top side (5.3.3 (a) (ii)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure bolt missing (5.3.3 (a) (i)) | 1 |
| Nearside Front Upper Suspension arm insecurely attached top arm bolt lose (5.3.3 (a) (i)) | 1 |
| Offside Front Upper Suspension arm insecurely attached top arm bolt loose (5.3.3 (a) (i)) | 1 |
| Emissions unable to be completed co to high on basic test (8.2.1.2 (d)) | 1 |
| Offside Front Vehicle structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced boot floor holed (6.1.1 (c) (i)) | 1 |
| Nearside Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced OUTTER SILL (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced OUTTER SILL (7.1.1 (a) (i)) | 1 |
| Offside Headlamp aim headlamp not in good working order adversely affecting beam image |1.2.4b| | 1 |
| Front Windscreen wiper not working |3.4 |a|| | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill, within 30cm of seat mounting. (6.1.1 (c) (i)) | 1 |
| Fuel cap/sealing device ineffective Temporary non locking cap fitted (6.1.3 (b) (i)) | 1 |
| Electrical wiring insecure and in contact with sharp edges Fouling steering column under bonnet (4.11 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired Chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired Chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill/floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Chassis (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jack point area (5.3.6 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases joint area (6.1.2 (a)) | 1 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached is detatched (5.3.4 (a) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear of outer sill |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear of outer sill |5.3.6 |a| |i|| | 1 |
| Front Anti-roll bar linkage cracked both |2.4.G.1| | 1 |
| Nearside Front Wheel bearing has excessive play rough when rotated (5.1.3 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under body (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under body (5.3.6 (a) (i)) | 1 |
| Offside Headlamp lens seriously defective poor beam image (4.1.1 (b) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded under wing area |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded under wing area |2.4.A.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases section |6.1.2 |a|| | 1 |
| Emissions not tested exhaust condition |8.2.1.2 |d|| | 1 |
| Nearside Rear Anti-roll bar linkage insecure and impairing directional stability broken off |5.3.3 |a| |ii|| | 1 |
| Nearside Front Wheel bearing rough when rotated & excessive play (5.1.3 (b) (i)) | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush broken |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage fractured drop link (5.3.3 (b) (ii)) | 1 |
| Offside Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Bumper insecure |6.1.4 |a| |i|| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassic rail |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is inadequately repaired chassic rail |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill too floor (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear silencer corroded and holed |7.1.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis at anti roll bar mounting area |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis at anti roll bar mounting area |2.4.A.3| | 1 |
| Rear Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Rear Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch |6.1.B.2| | 1 |
| Offside Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arche (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage insecure drop link broken |2.4.G.1| | 1 |
| Nearside Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Front Anti-roll bar linkage missing |5.3.3 |a| |ii|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak exhaust blowing at back box (8.2.1.1 (b)) | 1 |
| Windscreen damaged and affecting the driver`s view of the road |3.2 |a| |ii|| | 1 |
| Speedometer cannot be illuminated |7.8 |c| |ii|| | 1 |
| Nearside Rear Road wheel badly distorted |5.2.2 |c| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced BOTH OUTER SILLS ........ |7.1.1 |a| |i|| | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system brake caliper (1.1.11 (b) (ii)) | 1 |
| Offside Front Lower Suspension locking device missing balljoint nut half corroded (5.3.6 (b)) | 1 |
| Power steering malfunctioning lack of fluid (2.1.5 (a)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill holed marked in chalk (6.1.1 (c) (i)) | 1 |
| Seat belt missing no buckle fitted (7.1.2 (a)) | 1 |
| Rear Anti-roll bar linkage has excessive play in a ball joint both |2.4.G.2| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under vehicle and rear outer sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch / chassis area |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch / chassis area |5.3.6 |a| |i|| | 1 |
| Hydraulic fluid leaking excessively steering (8.4.1 (a) (i)) | 1 |
| Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis near inner arch |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis near inner arch |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Brake pipe leaking on a hydraulic braking system middle |1.1.11 |b| |ii|| | 1 |
| Nearside Seat belt cut sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Offside Seat belt cut sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Offside Rear Rear fog lamp has less than 50% of the light sources illuminating |1.3.2b| | 1 |
| Emissions not tested engine running hot (8.2.1.2 (d)) | 1 |
| Nearside Front Lower Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 1 |
| Nearside Rear Service brake excessively binding Unable to check wheel bearing (1.2.1 (f)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Floor / chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis within front subframe mount (5.3.6 (a) (i)) | 1 |
| Front Service brake excessively fluctuating both |1.2.1 |e|| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower inner sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower inner sill |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Lower Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits lambda 0.963 (8.2.1.2 (c)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits co 1.75 (8.2.1.2 (a)) | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Axle mount area (5.3.6 (a) (i)) | 1 |
| Emissions not tested Engine noise and possible risk of further damage. (8.2.1.2 (d)) | 1 |
| Centre Front Lower Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in front of the anti roll bar bracket (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in front of the anti roll bar bracket (5.3.6 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage insecure and impairing directional stability droplink snapped (5.3.3 (a) (ii)) | 1 |
| front brake binding both |3.7.B.1| | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s/r floor& outer sill |6.2.2 |d| |i|| | 1 |
| Rear front brake juddering severely |3.7.A.2b| | 1 |
| Power steering component leaking Steering rack area (2.1.5 (a)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill corroded within 30cms mounting |5.2.6| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Nearside Front Suspension arm insecure |2.4.G.1| | 1 |
| Nearside Front Headlamp light source and lamp not compatible LED fitted (4.1.4 (c)) | 1 |
| Offside Front Headlamp light source and lamp not compatible LED fitted (4.1.4 (c)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak at rear silencer (8.2.1.1 (b)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mount....|Inner wing| |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper chassis rail |5.3.6 |a| |i|| | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced Nearside and Offside (4.1.4 (b)) | 1 |
| Nearside Front rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Front rear brake recording little or no effort |3.7.B.5a| | 1 |
| Central Exhaust has a major leak of exhaust gases silencer blowing on join system corroded (6.1.2 (a)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt Lower swivel dust cover (5.3.4 (b) (ii)) | 1 |
| Nearside Front Service brake excessively binding WHEEL BEARING IS NOT TESTED (1.2.1 (f)) | 1 |
| Main beam tell-tale missing (4.9.1 (a) (ii)) | 1 |
| Stop lamp|s| not working centre |4.3.1 |a| |ii|| | 1 |
| Nearside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Front position lamp|s| not working Offside |1.1.A.3b| | 1 |
| Suspension component mounting prescribed area is excessively corroded Both sides front chassis,both sides outer sills,offside rear inner sill |2.4.A.3| | 1 |
| Nearside Rear Sub-frame rubber bush deteriorated resulting in excessive movement diff |2.4.G.2| | 1 |
| Offside Rear Sub-frame rubber bush deteriorated resulting in excessive movement diff |2.4.G.2| | 1 |
| Steering rack gaiter missing or no longer prevents the ingress of dirt nearside / offside damaged and twisted (2.1.3 (g) (ii)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced centre nearside / offside flooring (6.1.1 (c) (i)) | 1 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cill at front jacking point |6.1.B.2| | 1 |
| Nearside Rear Suspension arm mounting modified so the suspension is likely to fail other components inner bush bolt not correctly seated |5.3.3 |c| |ii|| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced front to rear inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor x2 |7.1.1 |a| |i|| | 1 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Emissions not tested no cat |8.2.1.2 |d|| | 1 |
| Emissions not tested no cat fitted |7.3.A.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner and outer sill (5.3.6 (a) (ii)) | 1 |
| Offside Front Lower Suspension component ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded FLOOR PAN BY SILL |MIDDLE| |5.2.6| | 1 |
| Offside Rear front brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Bonded suspension unit deteriorated and cannot function as intended |2.4.F.3| | 1 |
| Offside Front Bonded suspension unit deteriorated and cannot function as intended |2.4.F.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill hold (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill holed (7.1.1 (a) (i)) | 1 |
| Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front Front position lamp|s| not working both sides |1.1.A.3b| | 1 |
| Front Direction indicator incorrect colour both |1.4.A.2f| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked in yellow (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front/rear marked in yellow (5.3.6 (a) (i)) | 1 |
| Nearside Front Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Nearside Rear Brake linkage has restricted free movement |3.5.1k| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill see chalk |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill see chalk |5.2.6| | 1 |
| Emissions not tested due to vehicle overheating (8.2.1.2 (d)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired inner and outer sill repairs incomplete and not a continuous weld (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired inner and outer sill repairs incomplete and not a continuous weld, also hole in sill end plate stuffed with paper (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill/inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill/inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Hydraulic brake calliper leaking caliper leaking at union (1.1.16 (b) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced chassis leg below drivers seat corroded and holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded at floor to sill closing section |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded at floor to sill closing section |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength boot floor area |5.3.6 |a| |i|| | 1 |
| Offside Rear Anti-roll bar linkage insecurely attached broken (5.3.3 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Rear box hold next to hanger (6.1.2 (a)) | 1 |
| Exhaust has a major leak of exhaust gases Centre to rear on exhaust joint (6.1.2 (a)) | 1 |
| Exhaust has a major leak of exhaust gases CAT delete pipe to centre (6.1.2 (a)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak cat to centre on exhaust joint (8.2.1.1 (b)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases joint middle to rear |7.1.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded front anti roll bar |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis section for upper wishbone mountain and anti roll bar mountain |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Shock absorbers has an excessively worn bush Lower bush |5.3.2 |c|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel arch area |7.1.1 |a| |i|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength under bonnet (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension arm pin or bush likely to become detached pin loose (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill/inner arch area |6.1.1 |c| |i|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded floor pan |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is inadequately repaired sill |2.4.A.3| | 1 |
| Offside Inner Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Inner Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases middle |7.1.2| | 1 |
| Driver`s seat fore and aft adjustment mechanism not functioning as intended. |6.2.A.3| | 1 |
| Seat belt anchorage prescribed area is excessively corroded offside rear outer sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nearside rear outer sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nearside & offside floors |5.2.6| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Rear Upper Fuel pipe leaking around fuel tank area (6.1.3 (b) (i)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering outer sill |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner chassis in side off offside front wheel arch |6.1.A.1| | 1 |
| Brake lever has insufficient reserve travel no reserve travel (1.1.2 (a)) | 1 |
| Hand operated control valve lever inoperable from the driving position |3.2.2b| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill/floor (2 points) (6.2.2 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Back box |7.1.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases between rear box and centre section (6.1.2 (a)) | 1 |
| Rear Rear fog lamp switch faulty |1.3.1a| | 1 |
| Offside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases Rear section (6.1.2 (a)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sills both sides (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases At rear joint (6.1.2 (a)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both sides |4.1.4 |b|| | 1 |
| Front Headlamp aim projected beam image is obviously incorrect both sides |4.1.2 |c|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing area (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases flange section (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing area (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis section (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch and sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch and sill area (7.1.1 (a) (i)) | 1 |
| Inner Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Front Upper Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre floor area (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure is deformed and structural rigidity is significantly reduced Front chassis leg deformed (6.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Front chassis leg corroded (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Lower Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings As Marked |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings As Marked |6.1.B.2| | 1 |
| Offside Front Service brake excessively binding virtually unable to rotate the wheel by hand - brake locked on |1.2.1 |f|| | 1 |
| Brake inadequately mounted front to rear brake pipes |1.1.21 |c|| | 1 |
| Nearside Power steering ram|s| components fouling |2.3.4d| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings nearside and offside cills |6.1.B.2| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced 2 holes both marked with chalk bottom and side (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced marked with chalk (6.1.1 (c) (i)) | 1 |
| Offside Rear Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |
| Nearside Rear Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |
| Nearside Rear Rear reflector likely to become detached (4.8.1 (b) (ii)) | 1 |
| Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Offside Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Front Power steering pipe/hose excessively damaged excessively leaking (2.1.5 (g) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill - corroded though to inner sill |7.1.1 |a| |i|| | 1 |
| Emissions not tested exhaust rear pipe and box broken |8.2.1.2 |d|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis cracked |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/anti roll bar mount |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg |5.3.6 |a| |ii|| | 1 |
| Offside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected floor (5.3.6 (a) (ii)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected SHOCK MOUNT |5.3.6 |a| |ii|| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected SHOCK MOUNT |5.3.6 |a| |ii|| | 1 |
| Offside Front Lower Anti-roll bar linkage likely to become detached |5.3.3 |a| |ii|| | 1 |
| Nearside Front Lower Anti-roll bar linkage likely to become detached |5.3.3 |a| |ii|| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion Sills |6.1.C.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded hole in floor under seat |5.2.6| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg marked with yellow chalk |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg marked with yellow chalk |6.1.B.2| | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis rail, crushed from jacking and split (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill area (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill panel |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill |7.1.1 |a| |i|| | 1 |
| Power steering pipe/hose leaking Pipe above steering rack (2.1.5 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassi leg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassi leg |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill as marked |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill as marked |5.3.6 |a| |i|| | 1 |
| Seat belt anchorage prescribed area is inadequately repaired n/s sill o/s front wing |5.2.6| | 1 |
| Offside Front Service brake excessively binding wheel bearing not checked (1.2.1 (f)) | 1 |
| Offside Rear Anti-roll bar linkage likely to fail (5.3.3 (b) (ii)) | 1 |
| Offside Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` sun strip |8.3.1e| | 1 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced incorrect pattern |1.7.5a| | 1 |
| Headlamp adversely affected by the operation of another lamp when full beam is applied headlamps get interfearence |1.7.5c| | 1 |
| Offside Front Track rod end ball pin shank loose locking device missing |2.2.B.1c| | 1 |
| Front passenger door cannot be opened from outside the vehicle or inside the vehicle (6.2.3 (a)) | 1 |
| Front Headlamp aim not tested n/s and o/s obviously incorrectly fitted (4.1.2 (b)) | 1 |
| Brake performance not tested major fluid leak o/s/r (1.2.1 (g)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering suspension top.wheel arch.2 places |6.1.A.1| | 1 |
| Nearside Rear Anti-roll bar linkage fractured drop link |2.4.G.1| | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering floor |6.1.A.1| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill area excessively, most of the way along. (7.1.1 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Centre joint leaking, poor fit. (6.1.2 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill/floor area excessively corroded. (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassi |2.4.A.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases insecure |7.1.2| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill areas (7.1.1 (a) (i)) | 1 |
| Nearside Rear Brake cable has a seized clevis joint pivot |3.5.1c| | 1 |
| Brake pipe inadequately supported main |3.6.B.1| | 1 |
| Fuel pipe insecure main |7.2.1| | 1 |
| Nearside Rear Upper Suspension arm attachment bracket/mounting likely to become detached outer bolt has no nut and is drifting out |5.3.3 |a| |ii|| | 1 |
| Offside Outer Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting near to suspension mounting (6.2.2 (d) (i)) | 1 |
| Emissions not tested due to water leak/exhaust leak vehicle over heating water leak n/s/f sump area/ radiator hose area (8.2.1.2 (d)) | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings hole in floor |6.1.B.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor holed by seat mount |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor holed by seat mount |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer floor |5.3.6 |a| |i|| | 1 |
| Brake performance not tested rear brakes metal on metal |1.2.1 |g|| | 1 |
| Offside Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Emissions not tested due to oil leak |8.2.1.2 |d|| | 1 |
| rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
| Rear Electrical wiring inadequately supported |1.9.2a| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings subframe |6.1.B.2| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor section within subframe prescribed area (5.3.6 (a) (i)) | 1 |
| Nearside Front Macpherson strut insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Offside Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded floor/inner sill |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill area |5.2.6| | 1 |
| Offside Floor excessively deteriorated hole in sill (6.2.4 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt ball joint dust cover (5.3.4 (b) (ii)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Both front chassis legs |6.1.1 |c| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Strut mounting/inner wing |5.3.6 |a| |i|| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced body has hole (7.1.1 (a) (i)) | 1 |
| Offside Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened (5.3.1 (b) (i)) | 1 |
| Offside Front Braking system leaking Caliper |3.6.A.1| | 1 |
| Nearside Rear Braking system leaking Caliper |3.6.A.1| | 1 |
| Exhaust has a major leak of exhaust gases JOIN CAT TO CENTRE (6.1.2 (a)) | 1 |
| Brake performance not tested Due to burst brake pipe (1.2.1 (g)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis / wishbone mount |5.3.6 |a| |i|| | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system To front (1.1.11 (b) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor pan (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch at front (6.2.2 (d) (i)) | 1 |
| Nearside Inner Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front coil spring worn so that its cross sectional area is reduced and seriously weakened |2.4.C.1b| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired |6.2.2 |d| |ii|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired |6.2.2 |d| |ii|| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner & outersill |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner & outer sill |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill / inner wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened Chassis rail |5.3.3 |b| |i|| | 1 |
| Nearside Front Brake hose connection leaking on a hydraulic braking system |1.1.12 |c| |ii|| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis cracked/corroded (6.1.1 (c) (i)) | 1 |
| Rear fog lamp emits a light other than red white |1.3.2e| | 1 |
| Nearside Front brake caliper leaking Banjo Bolt |3.6.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill weak and holed by corrosion (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill weak and holed by corrosion (7.1.1 (a) (i)) | 1 |
| Front Shock absorber has an excessively worn bush BOTH SIDES |2.7.4| | 1 |
| Offside Front Horn not working (7.7 (a)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front of sub frame mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch area (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch area (7.1.1 (a) (i)) | 1 |
| Central Front Horn not working (7.7 (a)) | 1 |
| Rear Outer Integral body structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced sill sections both sides (6.1.1 (b) (ii)) | 1 |
| Offside Front Service brake excessively binding tight on rotation. (1.2.1 (f)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength hole. (5.3.6 (a) (i)) | 1 |
| Exhaust emissions carbon monoxide content excessive 0.60 closest to. (8.2.1.2 (b)) | 1 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Exhaust has a major leak of exhaust gases Rear joint corroded and broken off |7.1.2| | 1 |
| Emissions not tested Exhaust broken off |7.3.A.1| | 1 |
| Rear Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Offside Front Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg. |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg. |5.3.6 |a| |i|| | 1 |
| Brake disc in such a condition that it is seriously weakened x4 (1.1.14 (a) (ii)) | 1 |
| Offside Rear Brake performance not tested metal brake pipe failed whilst in rollers (1.2.1 (g)) | 1 |
| Offside Front Headlamp light intensity severely reduced Dip beam dull (4.1.4 (a)) | 1 |
| Nearside Outer Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings center |6.1.B.2| | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system front to back from hose |1.1.11 |b| |ii|| | 1 |
| Central Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
| Centre Rear Stop lamp not working high level |1.2.1b| | 1 |
| Nearside Front Lower Suspension arm locating pin locking device missing |2.4.G.3b| | 1 |
| Offside Rear Body has a projection caused by corrosion outer sill |6.1.C.1| | 1 |
| Exhaust has a major leak of exhaust gases centre box |7.1.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases tail pipe holed. (6.1.2 (a)) | 1 |
| Windscreen in such a condition that visibility through swept area is seriously affected over spray on front screen causing poor visibility and wipers not functioning as should. (3.2 (c) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis rail through osf wheel arche |2.4.A.3| | 1 |
| Emissions not tested due too exhaust (8.2.1.2 (d)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill |7.1.1 |a| |i|| | 1 |
| Front Braking system leaking to rear t joint brake pipe |3.6.A.1| | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marked in yellow (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marked in yellow (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marked in yellow (6.2.2 (d) (i)) | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced marked in yellow (6.1.1 (c) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is inadequately repaired chassis (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area is inadequately repaired chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength antiroll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor pan in more than one area |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor pan in more than one area |5.2.6| | 1 |
| Emissions not tested due to water leak |8.2.2.2 |e|| | 1 |
| Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced nsr outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail near to suspension arm (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail near to suspension arm (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases mid section at rear join |7.1.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill end corroded (7.1.1 (a) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis holed (6.1.1 (c) (ii)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users power steering |8.4.1 |a| |i|| | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired By anti roll bar D bush mount (6.2.2 (d) (ii)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired By anti roll bar D bush mount (6.2.2 (d) (ii)) | 1 |
| Offside Rear Lower Suspension spring mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected Spring saddle corroded (5.3.6 (a) (ii)) | 1 |
| Nearside Front Upper Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage insecurely attached Detached |5.3.3 |a| |i|| | 1 |
| Offside Front Steering system has a road wheel fouling a part of the vehicle |2.2.D.2a| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sillback. |5.2.6| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Sill/Inner Wheel Arch (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp aim beam image too far to the left |1.6.B4| | 1 |
| Offside Front Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
| Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Front suspension has a suspension upper ball joint securing nut loose |2.5.B.1a| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Inner wing 30cms of front lower anti roll bar mounting |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner cill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower brake caliper securing device loose |3.5.1j| | 1 |
| Nearside Front Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Front Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Rear fog lamp emits a light other than red white and red |1.3.2e| | 1 |
| Nearside Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength offside and nearside front chassis legs (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Within 30cm of seat mounting point (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Outer Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Exhaust emissions carbon monoxide content excessive CO TO HIGH. H C TO HIGH. |8.2.1.2 |b|| | 1 |
| Offside Rear Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Front Suspension component has an unsafe modification LOWER BALL JOINT SPLIT PIN MISSING. |5.3.3 |c| |i|| | 1 |
| Offside Front Suspension component has an unsafe modification LOWER BALL JOINT SPLIT PIN MISSING. |5.3.3 |c| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill
|2.4.A.3| | 1 |
| Rear Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
| Nearside Front Suspension arm locating pin locking device missing |2.4.G.3b| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer door sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Tie bar/rod synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Seat belt anchorage prescribed area is fractured chassis rail cracked |5.2.6| | 1 |
| Suspension component mounting prescribed area is excessively corroded n/s/f holed/chassis |2.4.A.3| | 1 |
| Offside Front Braking system leaking brake hose |3.6.A.1| | 1 |
| Rear Subframe mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 1 |
| Brake performance not tested Due to brake fluid leak |3.7.A.1| | 1 |
| Centre Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Offside Rear Lower Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Suspension arm ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Nearside Rear Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Anti-roll bar linkage ball joint excessively worn O/S REAR LINK ARM DETACHED AT THE BALL JOINT. (5.3.4 (a) (i)) | 1 |
| coil spring broken O/S REAR |2.4.C.1a| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering underwing |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering underwing |6.1.A.1| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases middle to back box joint |7.1.2| | 1 |
| Nearside Front Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Front passenger door does not latch securely closed |6.2.B.1a| | 1 |
| Offside Front Macpherson strut mounting has an unsafe modification Nut missing from top mounting under bonnet, marked white (5.3.3 (c) (i)) | 1 |
| Emissions not tested Cat missing so no emissions carried out (8.2.1.2 (d)) | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded inner + outer sill |2.4.A.3| | 1 |
| Nearside Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases exhaust box to middle section |7.1.2| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt bottom ball joint boot split open |2.4.G.2| | 1 |
| Offside Rear Lower Suspension arm damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Emissions not tested co high (8.2.1.2 (d)) | 1 |
| Emissions unable to be completed c o high (8.2.1.2 (d)) | 1 |
| Emissions not tested c/o high (8.2.1.2 (d)) | 1 |
| Emissions unable to be completed c/o high& lambda high (8.2.1.2 (d)) | 1 |
| Nearside Front Headlamp adversely affected by the operation of another lamp dip beam |1.7.5c| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill corroded/holed |6.1.B.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill corroded/holed |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail |6.1.B.2| | 1 |
| Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Integral body structure (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Integral body structure (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill section (7.1.1 (a) (i)) | 1 |
| Nearside Front Position lamp missing (4.2.1 (a) (ii)) | 1 |
| Nearside Front Coil spring mounting corroded and seriously weakened shock absorber (5.3.1 (b) (i)) | 1 |
| Offside Rear fog lamp does not emit a steady red light light lens faded |4.5.4 |a|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis /inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp aim not tested not working (4.1.2 (b)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect h4 (4.1.2 (c)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced box section on floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marker yellow (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marked yellow (6.2.2 (d) (i)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under front wing (5.3.6 (a) (i)) | 1 |
| Power steering ram leaking steering rack |2.1.5 |a|| | 1 |
| Nearside Front Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill and wheel arch |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill and wheel arch |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill holed |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill and wheel arch |2.4.A.3| | 1 |
| Offside Rear Wheel stud|s| missing |4.2.A.1e| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail marked with yellow chalk |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail marked with yellow chalk |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced to rear (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis both sides |2.4.A.3| | 1 |
| Nearside Front Headlamp not working on dipped beam loose con |1.7.5a| | 1 |
| Nearside Front Headlamp not working on main beam loose con |1.7.5a| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor to sill all along |5.2.6| | 1 |
| Rear Service brake imbalanced across an axle |1.2.1 |b| |i|| | 1 |
| Power steering inoperative drive belt missing (2.1.5 (c) (i)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassic leg holed (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassic leg (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area fractured significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill to floor aera |5.2.6| | 1 |
| Offside Front Upper coil spring fractured |2.4.C.1a| | 1 |
| Nearside Front Service brake excessively binding excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg side and lower |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill at rear (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill at rear (7.1.1 (a) (i)) | 1 |
| Nearside rear brake recording little or no effort Low brake readings |3.7.B.5a| | 1 |
| Nearside Electrical wiring deteriorated and bare wires exposed |1.9.2c| | 1 |
| Oil leaking excessively from transmission |8.4.1 |a| |i|| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced Both (4.1.4 (b)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis near anti roll bar mounting |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis near antiroll bar mounting |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed (7.1.1 (a) (i)) | 1 |
| Offside Front Upper Front suspension locking device missing |2.5.A.4| | 1 |
| Emissions not tested major leak of exhaust |7.3.A.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases both rear sections |7.1.2| | 1 |
| Passenger`s airbag obviously inoperative |7.1.5 |c|| | 1 |
| Headlamp aim not tested |4.1.2 |b|| | 1 |
| Brake performance unable to be tested Unable to test as the offside rear brake pipe burst (1.2.1 (g)) | 1 |
| Offside Rear Brake lever has restricted free movement calipre (1.1.15 (e)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 1 |
| Power steering fluid reservoir empty PIPE LEAKING (2.1.5 (b) (ii)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis under wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar linkage synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Lower Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Upper Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Brake pipe at imminent risk of failure or fracture FRONT TO REAR PIPE |1.1.11 |a|| | 1 |
| Brake pipe leaking on a hydraulic braking system FRONT TO REAR PIPE |1.1.11 |b| |ii|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced FLOOR HOLED (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced FLOOR HOLED (7.1.1 (a) (i)) | 1 |
| Power steering pipe|s| or hose|s| leaking one of the pipes |2.3.3b| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded Front subframe |2.4.A.3| | 1 |
| Brake pipe leaking Front to rear. |3.6.A.1| | 1 |
| Nearside Rear Parking (secondary brake) on a single line braking system grabbing severely (1.3.1 (c)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear outer and inner sill excessively corrode within 30cm of the seatbelt mounting point (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg excessively corroded in front of anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Offside Front Subframe mounting prescribed area is fractured |2.4.A.3| | 1 |
| Parking brake lever pawl spring does not push the pawl positively into the ratchet teeth |3.1.5| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis under wing |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis under wing |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering under arch |6.1.1 |c| |ii|| | 1 |
| Nearside Front Anti-roll bar linkage ball joint likely to become detached Has detached from upper ball joint |5.3.4 |a| |ii|| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to floor (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to floor (6.1.1 (c) (i)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits running rough idle to high (8.2.1.2 (c)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill jacking point (6.1.1 (c) (i)) | 1 |
| Parking |secondary brake| on a single line braking system imbalanced across an axle Axle 1 |1.3.1 |b| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer and inner sill |5.2.6| | 1 |
| Rear Anti-roll bar missing (5.3.3 (a) (ii)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch (5.3.6 (a) (i)) | 1 |
| Offside Outer Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Outer Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded chassis leg holed |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded on chassis leg |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded chassis leg holed |2.4.A.3| | 1 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened holed |2.4.G.1| | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened holed |2.4.G.1| | 1 |
| Rear Body obviously not squarely located on chassis |6.2.2 |b|| | 1 |
| Offside Rear Body component corroded and likely to cause injury rear wheel arch |6.2.1 |a| |i|| | 1 |
| Rear Parking brake inoperative on one side both sides no effort (1.4.1 (a)) | 1 |
| Exhaust has a major leak of exhaust gases middle around the cat area (6.1.2 (a)) | 1 |
| Front Steering system fouling |2.2.D.2a| | 1 |
| Front Power steering pipe/hose leaking |2.1.5 |a|| | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Lower Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill hold (5.3.6 (a) (i)) | 1 |
| Emissions not tested due to engine overheating (8.2.1.2 (d)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor by drivers seat mount |5.2.6| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced FLOOR (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced FLOOR (6.1.1 (c) (i)) | 1 |
| Passenger`s airbag missing |5.4.1| | 1 |
| Nearside Front Wheel stud|s| missing |4.2.A.1e| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outersill |5.2.6| | 1 |
| Nearside Front Direction indicator not working Wing |1.4.A.2c| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch, under bonnet (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill and inner arch (7.1.1 (a) (i)) | 1 |
| Emissions not tested exhaust blowing |7.3.A.1| | 1 |
| Nearside Outer Front Lower Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Rear Shock absorber insecure |2.7.2b| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded outer sill panel |5.2.6| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive See sheet |7.3.D.3| | 1 |
| Nearside Front Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting chassis leg (6.2.2 (d) (i)) | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings to rear sill |6.1.B.2| | 1 |
| Nearside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Tail section missing. |7.1.2| | 1 |
| Suspension component mounting prescribed area is excessively corroded Both rear outer sills |2.4.A.3| | 1 |
| Power steering pipe/hose excessively corroded Leaking (2.1.5 (g) (i)) | 1 |
| Emissions not tested vehicle overheated |8.2.1.2 |d|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Between anti roll bar mount and sub frame |6.2.2 |d| |i|| | 1 |
| Nearside Rear Hydraulic fluid leaking excessively Brake caliper |8.4.1 |a| |i|| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Wheel arch corroded. |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired outer sill |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded view from under the wheel arch area |2.4.A.3| | 1 |
| Offside Headlamp aim beam image obviously incorrect Bulb fitted incorrectly |1.8.A.1b| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings of sill |6.1.B.2| | 1 |
| Brake pedal pad not secure to the pedal |3.3.A.1c| | 1 |
| Offside Front Seat belt not functioning as intended unable to pull out correctly (7.1.2 (c)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail, near to shock absorber. under wheel arch (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear box (6.1.2 (a)) | 1 |
| Exhaust has a major leak of exhaust gases centre pipe (6.1.2 (a)) | 1 |
| Offside Rear Lower Macpherson strut mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Battery insecure |1.9.1| | 1 |
| Nearside Front Lower Macpherson strut mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Front Lower Macpherson strut mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Position lamp not working All (4.2.1 (a) (ii)) | 1 |
| Headlamp not working on dipped beam Both (4.1.1 (a) (ii)) | 1 |
| Headlamp not working on main beam Both (4.1.1 (a) (ii)) | 1 |
| Exhaust emissions - engine idle speed too high Test aborted (8.2.1.2 (e)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Lower chassis rail holed x2 by corrosion-within 30cm of subframe mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid Caliper |1.1.16 |b| |i|| | 1 |
| Front Obligatory mirror missing |8.1.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor/outrigger |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced mid floor |7.1.1 |a| |i|| | 1 |
| Offside Rear Hydraulic fluid leaking excessively Brake caliper |8.4.1 |a| |i|| | 1 |
| Offside Front Vehicle structure has a fracture which is likely to adversely affect braking or steering CHASSIS |6.1.1 |a| |ii|| | 1 |
| Nearside Front Lower Anti-roll bar ball joint likely to become detached detached (5.3.4 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill area. (5.3.6 (a) (i)) | 1 |
| Offside Front Service brake excessively binding 20 kg bind |1.2.1 |f|| | 1 |
| Nearside Front Driver`s seat insecure |6.2.A.1| | 1 |
| Nearside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
| Offside Front Body has a sharp edge caused by corrosion inner wing |6.1.C.1| | 1 |
| Service brake excessively binding both front |1.2.1 |f|| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Brake hose excessively damaged |1.1.12 |b| |ii|| | 1 |
| Nearside Rear Brake hose excessively damaged |1.1.12 |b| |ii|| | 1 |
| Offside Rear Brake hose excessively damaged |1.1.12 |b| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS (5.3.6 (a) (i)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury WHEEL ARCH (6.2.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Front Position lamp not working side lamp (4.2.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wing (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wing (5.3.6 (a) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced n/s outer sill panel corroded near seatbelt mounting point (7.1.1 (a) (i)) | 1 |
| Nearside Front position lamp|s| not working 501 |1.1.A.3b| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill. (7.1.1 (a) (i)) | 1 |
| Nearside Main beam `tell-tale` not working |1.7.4c| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Lower Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis rail |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chasiss rails |6.1.A.1| | 1 |
| Exhaust has a major leak of exhaust gases on joints |7.1.2| | 1 |
| Front position lamp|s| not working both front side lights not working |1.1.A.3b| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis/innerwing holed |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis/innerwing holed |6.1.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength engine bay (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded through. (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill corrosion perforated. (7.1.1 (a) (i)) | 1 |
| Nearside Front Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Outer Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis leg holed on the outer side and underneath |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis leg holed underneath |2.4.A.3| | 1 |
| Offside Rear Lower Radius arm severely distorted |2.4.G.1| | 1 |
| Emissions not tested engine revs keep cut on and off unable to hold steady revs (8.2.1.2 (d)) | 1 |
| Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
| Nearside front brakes release unevenly |3.7.B.4| | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper (1.1.16 (b) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill / wheel arch |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill / wheel arch |2.4.A.3| | 1 |
| Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Coil spring mounting corroded and seriously weakened |2.4.C.3c| | 1 |
| Nearside Front Lower Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Front Lower Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases Back Box Missing |6.1.2 |a|| | 1 |
| Front Service brake excessively binding Both |1.2.1 |f|| | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Both outer sills at front and rear |6.2.2 |d| |i|| | 1 |
| Nearside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill section (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced unsafe repair filler applied (6.1.1 (d) (i)) | 1 |
| Offside Front Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced seem weld not applied on all sides (6.1.1 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced unsafe repair filler applied (6.1.1 (d) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill corroded (6.2.2 (d) (i)) | 1 |
| Offside Front Body panel likely to become detached (6.2.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Hole within limit of anti roll bar mounting point (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension arm has excessive play in a pin/bush outer bushes |2.4.G.2| | 1 |
| Nearside rear brake recording little or no effort hand brake |3.7.B.5a| | 1 |
| Offside Front Lower Steering linkage ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Under sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Under sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under sill corroded/hole (6.1.1 (c) (i)) | 1 |
| Rear Anti-roll bar linkage has an unsafe modification Both incorrectly fitted (5.3.3 (c) (i)) | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced o/s & n/s outer sills |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded At rear of sill |5.2.6| | 1 |
| Driver`s seat fore and aft adjustment mechanism not functioning as intended. or should be welded |6.2.A.3| | 1 |
| Drivers airbag missing steering wheel (7.1.5 (a)) | 1 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength At anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength At anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/floor pan area (6.1.1 (c) (i)) | 1 |
| front brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chaqssis leg (5.3.6 (a) (i)) | 1 |
| Front Seat belt buckle not functioning as intended both , wont pull out properly ,keep sticking (7.1.2 (d)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear brake disc contaminated by oil |3.5.1h| | 1 |
| Nearside Front Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength wheel arch to chassis |5.3.6 |a| |i|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded body sill panel |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chasis |2.4.A.3| | 1 |
| Offside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Nearside Front Lower Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WING (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering @ brake pipes |6.1.A.1| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength BOTH FRONT FLOORS |5.3.6 |a| |i|| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength BOTH REAR OUTER SILLS |5.3.6 |a| |i|| | 1 |
| Position lamp with a multiple light source more than 1/2 not functioning all side lights not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Coil spring fractured or broken broken at top coil (5.3.1 (b) (i)) | 1 |
| front brake binding Both |3.7.B.1| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Both sills |rear| |6.1.B.2| | 1 |
| Central Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Under vehicle behind sill |6.1.B.2| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion Wheel arch |6.1.C.1| | 1 |
| Anti-roll bar linkage has excessive play in a ball joint Both rear |2.4.G.2| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength seal as marked (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength seal as marked (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength seal as marked (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis under arch area. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Brake hose excessively damaged |3.6.B.4d| | 1 |
| Nearside Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill / floor and chassis |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases front to centre joint |7.1.2| | 1 |
| Nearside Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded o/s outer sill and sill end |5.2.6| | 1 |
| Brake performance not tested Due to excessively binding N/S/F brake (1.2.1 (g)) | 1 |
| Nearside Front Hydraulic brake calliper leaking brake caliper leaking (1.1.16 (b) (i)) | 1 |
| Nearside Front Inner Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Rail |5.3.6 |a| |i|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Rail |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Front Exhaust has a major leak of exhaust gases at cat flange |7.1.2| | 1 |
| Nearside Rear Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Rear Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner bumper corner/ floor |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner bumper corner/ floor |2.4.A.3| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill panel |5.3.6 |a| |i|| | 1 |
| Offside Front Upper Suspension arm locating pin retaining device missing |2.4.G.3b| | 1 |
| Nearside Front Service brake excessively fluctuating binding |1.2.1 |e|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded arch. |2.4.A.3| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg outer |6.1.B.2| | 1 |
| Braking system leaking front to back pipe |3.6.A.1| | 1 |
| Offside Rear Anti-roll bar linkage insecure and impairing directional stability |5.3.3 |a| |ii|| | 1 |
| Nearside Headlamp light source and lamp not compatible |4.1.4 |c|| | 1 |
| Offside Headlamp light source and lamp not compatible |4.1.4 |c|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis |6.1.1 |c| |i|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis/crossmember |6.1.1 |c| |i|| | 1 |
| Offside Rear Rear fog lamp insecure |1.3.2a| | 1 |
| Emissions not tested due to very high c/o |8.2.1.2 |d|| | 1 |
| brake drum excessively pitted |3.5.1h| | 1 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Offside Outer Brake pipe leaking |3.6.A.1| | 1 |
| Offside Front Statutory seat belt missing |5.1.1| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassie leg |5.3.6 |a| |ii|| | 1 |
| Headlamp not working on main beam Nearside |1.7.5a| | 1 |
| Rear Exhaust has a major leak of exhaust gases clamp insecure |7.1.2| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassi |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassi |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill holed & rusted |2.4.A.3| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.074% (8.2.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect lens clouded (4.1.2 (c)) | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system Brake pipe. (1.1.11 (b) (ii)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Chassis corrosion visible in wheelarch |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Chassis corrosion visible in wheelarch |6.1.B.2| | 1 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened wishbone |5.3.3 |b| |i|| | 1 |
| Offside Rear Lower Suspension arm corroded and seriously weakened wishbone |5.3.3 |b| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mount |5.3.6 |a| |i|| | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension arm mount|inner sill| |5.3.6 |a| |i|| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension arm mount |inner sill| |5.3.6 |a| |i|| | 1 |
| Offside Outer Vehicle structure has excessive corrosion which adversely affects braking or steering Sill |6.1.1 |c| |ii|| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering Nearside inner wing |6.1.1 |c| |ii|| | 1 |
| Suspension arm corroded and seriously weakened Nearside and offside front bottom arms |5.3.3 |b| |i|| | 1 |
| Offside Outer Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Offside Outer Rear Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Offside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear Service brake excessively binding on both side (1.2.1 (f)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corrosion |7.1.1 |a| |i|| | 1 |
| Nearside Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Rear fog lamp likely to become detached |4.5.1 |c| |ii|| | 1 |
| Power steering component leaking leak from rack |2.1.5 |a|| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting fractured |5.3.3 |b| |ii|| | 1 |
| Rear All position lamps not working |1.1.A.3b| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill excessively corroded within 30cm of seat runner/seat belt mounting point. (7.1.1 (a) (i)) | 1 |
| Offside Front brake caliper has restricted free movement brake binding |3.5.1k| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced N/S headlamp cloudy no beam pattern (4.1.4 (b)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg corroded, small hole on previous repair (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired outer sill repair not seam welded across bottom (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed and full of filler (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength bottom of chassis leg corroded above anti roll bar d bush (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arm shock absorber mountain |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Subframe mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill/wheel arch |5.2.6| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering under arch |6.1.A.1| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded under arch |2.4.A.3| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings clouser panel |6.1.B.2| | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both sides (4.1.4 (b)) | 1 |
| Offside Front Anti-roll bar linkage fractured broke (5.3.3 (b) (ii)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill middle and rear (6.1.1 (c) (i)) | 1 |
| Offside Rear Brake hose damaged and likely to fail hose is clamped (1.1.12 (a)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg |6.2.2 |d| |i|| | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached no locking device on balljoint (5.3.4 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached bolt holding ball joint to arm loose (5.3.4 (a) (ii)) | 1 |
| Offside Parking brake inoperative on one side cable retaining bracket fitted incorrectly and not adjusted (1.4.1 (a)) | 1 |
| Offside Rear Sub-frame attachment bracket/mounting insecure rear sub frame stabilizing bar loose (5.3.3 (a) (i)) | 1 |
| Supplementary Restraint System warning lamp indicates a fault air bag |5.4.2| | 1 |
| Nearside Front Lower Radius arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Lower Anti-roll bar attachment bracket/mounting fractured |5.3.3 |b| |ii|| | 1 |
| Nearside Front Lower Power steering pipe|s| or hose|s| leaking PAS Return pipe has serious fluid leak |2.3.3b| | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush droplink |2.4.G.2| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Corroded/Hole in floor below drivers seat. (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Damage/Split in floor below rear of drivers seat. (7.1.1 (a) (i)) | 1 |
| Front Rear fog lamp switch not operating in accordance with the requirements Rear fog light does not remain on. (4.5.3 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor holed (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded and holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded and holed (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Suspension arm mount/chassis leg (5.3.6 (a) (i)) | 1 |
| front parking |secondary| brakes imbalanced |3.7.B.6b| | 1 |
| Front Sub-frame inappropriately repaired |2.4.A.2| | 1 |
| Front Sub-frame insecure |2.4.G.1| | 1 |
| Emissions not tested due to radiator failure during test (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (X2) (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced chassis rail (7.1.1 (a) (i)) | 1 |
| Nearside Rear Brake pipe connection leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 1 |
| Offside Rear Braking system leaking metal pipe corroded |3.6.A.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper chassis |5.3.6 |a| |i|| | 1 |
| Front position lamp|s| incorrect colour both |1.1.A.3e| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is inadequately repaired Sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassi next to roll bar mounts (5.3.6 (a) (i)) | 1 |
| Nearside Front Direction indicators missing |1.4.A.2b| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Rear Emissions not tested hole in exhaust system (8.2.1.2 (d)) | 1 |
| Offside Rear Brake performance not tested brake pipe leaking osr (1.2.1 (g)) | 1 |
| Nearside Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Front to Rear (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg | under inner wheel arch| |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg | under inner wheel arch| |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Floor to sill |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases Rear tail pipe |7.1.2| | 1 |
| Brake performance not tested due to leaking (1.2.1 (g)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment no reserve travel |1.1.6 |c|| | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired silland o/s outer sill (6.2.2 (d) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Near side out seal corroded/holed. (7.1.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint Broken |2.4.G.2| | 1 |
| Horn not working no switch or button (7.7 (a) (ii)) | 1 |
| Offside Rear Upper Shock absorbers damaged to the extent that it does not function (5.3.2 (b)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inside wheel arch chassis |2.4.A.3| | 1 |
| Offside Rear Body component damaged and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg under arch area (6.1.1 (c) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side inefficient (1.4.1 (a)) | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen no beam image |4.1.2 |a|| | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen no beam image |4.1.2 |a|| | 1 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear fog lamp not working |1.3.2b| | 1 |
| Front Power steering pipe|s| or hose|s| inappropriately repaired |2.3.7| | 1 |
| Front Power steering inoperative |2.3.3a| | 1 |
| Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Nearside Rear Body insecure outer sill |6.2.2 |a| |i|| | 1 |
| Offside Front Body insecure outer sill |6.2.2 |a| |i|| | 1 |
| Nearside Front Body insecure inner arch |6.2.2 |a| |i|| | 1 |
| Offside Front Body insecure inner arch |6.2.2 |a| |i|| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Offside Front Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
| Body has a sharp edge caused by corrosion both rear outer wheelarches |6.1.C.1| | 1 |
| Emissions not tested exhaust tail pipe not present.broken off |7.3.A.1| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect Bulb not in corectly |1.8.A.1b| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills (5.3.6 (a) (i)) | 1 |
| Nearside Rear Body component damaged and likely to cause injury light lens (6.2.1 (a) (i)) | 1 |
| Offside Side repeater light intensity significantly reduced (4.4.3 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre (7.1.1 (a) (i)) | 1 |
| Horn is a siren |1.6.2c| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Jacking point |5.2.6| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside An item not tested |Manual| | 1 |
| Offside An item not tested |Manual| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded n/s/r sill holed and corroded within 30cms of seatbelt mounting |5.2.6| | 1 |
| Power steering pipe|s| or hose|s| leaking pipe to cooler |2.3.3b| | 1 |
| Seat belt anchorage prescribed area is excessively corroded o/s/r 1/4 panel |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor/sill |5.2.6| | 1 |
| Nearside Panhard rod attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Offside Panhard rod attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Braking system leaking Rear metal brake pipe |3.6.A.1| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded Inner wing area |2.4.A.3| | 1 |
| Steering lock fails to engage |2.1.4b| | 1 |
| Driver`s seat insecure bolt loose |6.2.A.1| | 1 |
| Passenger`s seat insecure bolt loose |6.2.A.1| | 1 |
| Nearside Front Upper Front suspension locking device missing ball joint split pin |2.5.A.4| | 1 |
| Offside Front Macpherson strut insecure shock to mount nut |2.4.G.1| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis member |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis member |2.4.A.3| | 1 |
| Offside Rear Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill by |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill by |5.2.6| | 1 |
| Nearside Front Upper Front passenger door hinge insecure |6.2.3 |c| |ii|| | 1 |
| Nearside Brake pipe inadequately supported Front to rear pipe touching body |3.6.B.1| | 1 |
| Braking system leaking ABS Pump |3.6.A.1| | 1 |
| Offside Front Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill front and rear some small holes |6.1.B.2| | 1 |
| Rear Sub-frame rubber bush bonding deteriorated resulting in excessive movement BOTH |2.4.G.2| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded wing |5.2.6| | 1 |
| Nearside Front Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Rear Sub-frame insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Front Side repeater missing (4.4.1 (a) (ii)) | 1 |
| Offside Front Side repeater missing (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Front Hydraulic fluid leaking excessively power steering fluid (8.4.1 (a) (i)) | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases near new clamp (6.1.2 (a)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch section (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch section (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded OUTER SILL |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded UNDER WING |2.4.A.3| | 1 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached Has detached (5.3.4 (a) (ii)) | 1 |
| Outer Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Centre Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Front Anti-roll bar linkage cracked |2.4.G.1| | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired inner and outer cill (6.2.2 (d) (ii)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired inner and outer cill (6.2.2 (d) (ii)) | 1 |
| Headlamp aim beam image obviously incorrect both lenses faded |1.8.A.1b| | 1 |
| Supplementary restraint system warning lamp indicates a fault air bag warning light flashing (7.1.6 (a)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced A Pillar (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced A Pillar (6.1.1 (c) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases Centre / rear |6.1.2 |a|| | 1 |
| Offside Rear Anti-roll bar locating pin insecure |2.4.G.3a| | 1 |
| Offside Rear Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Headlamp does not operate immediately when selected on main beam loose connection |1.7.4a| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill |5.2.6| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sil |6.1.1 |c| |i|| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sil |6.1.1 |c| |i|| | 1 |
| Nearside Front Upper Suspension arm pin or bush excessively worn both bushes (5.3.4 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill |5.2.6| | 1 |
| Rear rear parking |secondary| brake grabbing severely both |3.7.B.6b| | 1 |
| Offside Front Macpherson strut insecure |2.4.G.1| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 1 |
| Offside Front Shock absorbers insecurely attached lower nut and bolt loose (5.3.2 (a) (i)) | 1 |
| Nearside Rear Shock absorbers insecurely attached lower bolt loose (5.3.2 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded/holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill section (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings To rear chassis sections |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings To rear inner sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill inner |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Wheelarch |6.1.B.2| | 1 |
| Offside Front Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded inner sill corroded and holed |5.2.6| | 1 |
| Brake pedal has insufficient reserve travel Spongey |1.1.2 |a|| | 1 |
| Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis holed Both sides |6.2.2 |d| |i|| | 1 |
| Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer sills holed Both sides |6.2.2 |d| |i|| | 1 |
| Offside Rear Hydraulic fluid leaking excessively brake caliper |8.4.1 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch area |5.3.6 |a| |i|| | 1 |
| Offside Rear Coil spring with an unsafe modification been welded (5.3.1 (d) (i)) | 1 |
| Rear Suspension component insecurely attached (5.3.3 (a) (i)) | 1 |
| Electronic braking system warning device indicates a fault (1.7 (b)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing / chassis leg under bonnet x2 (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor / chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor / chassis (7.1.1 (a) (i)) | 1 |
| Nearside Inner Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Inner Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Outer Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Outer Upper Bonded suspension unit attachment loose |2.4.F.1a| | 1 |
| Centre Front Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Nearside Rear Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill and floor area (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor area (5.3.6 (a) (i)) | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassie affecting suspention |6.1.B.2| | 1 |
| Offside Rear Position lamp not working |4.2.1 |a| |ii|| | 1 |
| Anti-roll bar linkage insecure upper droplink come away |2.4.G.1| | 1 |
| Undertray likely to become detached |6.2.1 |a| |ii|| | 1 |
| Rear Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Front Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Front Power steering inoperative and steering adversely affected leaking |2.1.5 |c| |ii|| | 1 |
| Nearside Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill |6.2.2 |d| |ii|| | 1 |
| Offside Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill |6.2.2 |d| |ii|| | 1 |
| Nearside Power steering ram leaking |2.1.5 |a|| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inside inner arch |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced body sill panel (7.1.1 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Rear Brake pipe leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) | 1 |
| Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt o/s/n/s (5.3.4 (b) (ii)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s/n/s outer sill (5.3.6 (a) (i)) | 1 |
| Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting area excessively corroded both sides (5.3.6 (a) (i)) | 1 |
| Nearside Front Road wheel badly distorted rubbing against inner wing (5.2.2 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced lower outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Subframe mounting prescribed area is excessively corroded sill/floor |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area is excessively corroded osr inner sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded osr sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nsr sill |5.2.6| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength osf box section (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill & inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill/floor |5.2.6| | 1 |
| Offside Rear Outer Suspension arm corroded and seriously weakened sill |2.4.G.1| | 1 |
| Nearside Front Lower Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` national trust sticker |8.3.1e| | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor and outer sill area |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing area |2.4.A.3| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill. (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill. (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chasis rail |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chasis rail |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced O/S Sill corroded excessively marked yellow (7.1.1 (a) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Corrosion on the N/S/R of the vehicle within 30cm of the subframe mounting point (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.60% (8.2.1.2 (b)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.03 lambda (8.2.1.2 (c)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn ball joint has excessive movement (5.3.4 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded under sill/floor centre |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded under sill/floor at centre |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded under sill |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill and floor corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced underbody sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Front position lamp|s| has less than 50% of the light sources illuminating dull |1.1.A.3b| | 1 |
| Offside Front Front position lamp|s| has less than 50% of the light sources illuminating dull |1.1.A.3b| | 1 |
| Offside Front Brake prescribed area is inadequately repaired floor pan (1.1.21 (e) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Centre inner seal |6.2.2 |d| |i|| | 1 |
| Offside Rear An item not tested |Manual| | 1 |
| All position lamps not working front /rear |1.1.A.3b| | 1 |
| Rear Exhaust has a major leak of exhaust gases rear joints corroded and leaking |7.1.2| | 1 |
| Offside Front Windscreen wiper blade missing (3.4 (b) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassies (5.3.6 (a) (i)) | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill outer panel and wheel arch excessively corroded |6.1.B.2| | 1 |
| Emissions not tested exhaust emissions reading too high due to burning oil |7.3.A.1| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint ball joint has excessive play |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint excessive play in ball joint |2.4.G.2| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded chassis holed at suspension mounting forward |2.4.A.3| | 1 |
| Front Headlamp lens seriously defective both |4.1.1 |b| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired inner wheel arch area. weld repair is not continuous (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch area (5.3.6 (a) (i)) | 1 |
| Offside Rear Hydraulic fluid leaking excessively Brake pipe split (8.4.1 (a) (i)) | 1 |
| Offside Front Brake fluid significantly below minimum mark |1.1.10 |d| |ii|| | 1 |
| Front front brake grabbing severely |3.7.A.2b| | 1 |
| Rear Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.D.1| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch area |6.1.B.2| | 1 |
| Suspension component mounting prescribed area is excessively corroded o/s/f inner sill |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill x2 |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded centre inner sill |5.2.6| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition rear silencer
|7.1.4| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded o/s/f seat mount excessively corroded |5.2.6| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened front chassis |5.3.3 |b| |i|| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened front chassis |5.3.3 |b| |i|| | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect bulb incorrectly fitted (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim beam image kick up to the offside |1.6.B1| | 1 |
| Central Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Offside Rear Suspension arm likely to become detached nearly broken off (advise mot to drive) (5.3.3 (a) (ii)) | 1 |
| Brake performance not tested due to condition of rear lower arms (dangerous) (1.2.1 (g)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor directly under drivers seat |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 1 |
| Nearside Front Anti-roll bar corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Front Anti-roll bar corroded and seriously weakened |2.4.G.1| | 1 |
| Front Power steering component|s| leaking steering pipe |2.3.3b| | 1 |
| Offside Rear Anti-roll bar linkage which is adjustable, locking device insecure |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg by anti roll bar bracket (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg by anti roll bar bracket (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill
|5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases Intermediate/silencer joint corroded away |7.1.2| | 1 |
| Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis |5.3.6 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired OUTER SILL |5.3.6 |a| |i|| | 1 |
| Offside Front Seat belt damaged seat belt is fraying and the structure of the belt is compromised (7.1.2 (b) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan holed and corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Body has a sharp edge caused by corrosion sealing |6.1.C.1| | 1 |
| Offside Rear Sub-frame severely distorted |2.4.G.1| | 1 |
| Offside Rear Upper Suspension arm severely distorted |2.4.G.1| | 1 |
| Exhaust has a major leak of exhaust gases rear exhaust joint connecting to the center joint |7.1.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outersill |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outersill |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded rear outer sill |5.2.6| | 1 |
| Nearside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch at top (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength where inner arch meets sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced holed by corrosion (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm fractured |5.3.3 |b| |ii|| | 1 |
| Offside Front Service brake lagging in operation |1.2.1 |d|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded & holed (7.1.1 (a) (i)) | 1 |
| Offside Track rod end ball joint has excessive play Lock nut loose and Dangerous (2.1.3 (b) (i)) | 1 |
| Nearside Front Upper Suspension arm corroded and seriously weakened Chassis corroded (5.3.3 (b) (i)) | 1 |
| Nearside Front Upper Suspension arm ball joint likely to become detached Crown nut locking pin missing (5.3.4 (a) (ii)) | 1 |
| Nearside Front Track rod end ball joint worn to the extent there is a serious risk of detachment Crown nut locking pin missing (2.1.3 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached nut not done up (5.3.4 (a) (ii)) | 1 |
| Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Headlamp aim so that beam "kick up" is not visible on the screen both front |4.1.2 |a|| | 1 |
| Nearside Front Subframe mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor |7.1.1 |a| |i|| | 1 |
| Nearside Side repeater insecure |1.4.A.2b| | 1 |
| Offside Front Front position lamp|s| not working side light |1.1.A.3b| | 1 |
| Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear position lamp|s| not working left |1.1.A.3b| | 1 |
| Stop lamp not working left |1.2.1b| | 1 |
| coil spring broken both front |2.4.C.1a| | 1 |
| Suspension component mounting prescribed area is excessively corroded front antiroll bar mounting area, both sides |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer cill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer door sill |5.2.6| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to sill (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail x2 (6.1.1 (c) (i)) | 1 |
| Nearside Front Power steering pipe/hose leaking oil cooler (2.1.5 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced undersill |7.1.1 |a| |i|| | 1 |
| Front Windscreen excessively tinted and visibility through swept area of windscreen seriously affected (3.2 (b) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is fractured sill |5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases tail pipe |7.1.2| | 1 |
| Nearside Rear Braking system leaking leak from caliper |3.6.A.1| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint lower arm outer ball joint |2.4.G.2| | 1 |
| Offside Floor excessively deteriorated several holes front too rear (6.2.4 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded drivers seat floor area |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wing (7.1.1 (a) (i)) | 1 |
| Offside Rear Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Stop lamp(s) not working center brake light (4.3.1 (a) (ii)) | 1 |
| Emissions not tested Excessively rich and off the scale, engine stalling. (8.2.1.2 (d)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded underside |5.2.6| | 1 |
| Offside Front Anti-roll bar linkage modified and seriously weakened |2.4.A.2| | 1 |
| Offside Lower Front suspension locking device missing |2.5.A.4| | 1 |
| Offside Front Upper Front suspension retaining device ineffective |2.5.A.4| | 1 |
| Emissions not tested co of the scale |7.3.A.1| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor pan (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor pan (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill back |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill back |7.1.1 |a| |i|| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 1 |
| Front Anti-roll bar linkage ball joint excessively worn Both sides (5.3.4 (a) (i)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Both sides chassis leg in wheel arches (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired SILL SPLITTING AWAY (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits .66% (8.2.1.2 (a)) | 1 |
| Offside Front Steering rack has excessive free play detected at the steering wheel (steering rack fitted) inner steering rack ball joint end excess play (2.3 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg & inner wing panel (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg & inner wing panel (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sil |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sil |5.3.6 |a| |i|| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced BOTH (4.1.4 (b)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor/inner sill |7.1.1 |a| |i|| | 1 |
| Offside Lower Front suspension has excessive play in an outer ball joint |2.5.B.2a| | 1 |
| Offside Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Rear Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Front Lower Suspension component ball joint excessively worn Both sides (5.3.4 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sills |7.1.1 |a| |i|| | 1 |
| Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Emissions not tested due to blow on exhaust |7.3.A.1| | 1 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn both outer bushes (5.3.4 (a) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect both headlamps cloudy (4.1.2 (c)) | 1 |
| Offside Rear Lower Suspension arm pin or bush excessively worn both outer bushes (5.3.4 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension arm insecure bolt loose |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis leg, inner arch. |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis leg, inner arch. Two places. |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is inadequately repaired Chassis leg near to sub-frame mount. |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired Chassis leg near to sub-frame mount. |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Outer centre sill area. |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Centre outer sill area. |5.2.6| | 1 |
| Offside Rear Upper Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Rear Braking system leaking Caliper |3.6.A.1| | 1 |
| Offside Front Anti-lock braking system wiring excessively damaged |3.4.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded centre, chassis member |5.2.6| | 1 |
| Front position lamp|s| not working both side lights |1.1.A.3b| | 1 |
| Emissions not tested boiled (8.2.1.2 (d)) | 1 |
| Position lamp not working all side position lamps inop (4.2.1 (a) (ii)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment full travel and no effort (1.1.6 (c)) | 1 |
| Nearside Rear Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Centre Front Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Offside Rear Rear fog lamp obviously incorrectly positioned |1.3.2a| | 1 |
| Centre Front Brake pedal spongy |3.3.B.1b| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Inner arch |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Arch |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Inner arch |5.2.6| | 1 |
| Offside Front Anti-roll bar linkage insecure anti roll bar end link |2.4.G.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill Chalked (7.1.1 (a) (i)) | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s/r floor |6.1.B.2| | 1 |
| Emissions not tested EXHAUST LEAK. (8.2.1.2 (d)) | 1 |
| Exhaust emissions carbon monoxide content at idle excessive Aborted |7.3.D.4| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Nearside Rear Anti-roll bar worn and seriously weakened |2.4.G.1| | 1 |
| Offside Front Anti-lock braking system wheel speed sensor missing |1.6 |c|| | 1 |
| Exhaust system insecure 2 rubber mountings broken (6.1.2 (a)) | 1 |
| Nearside Rear Parking brake inoperative on one side weak (1.4.1 (a)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.73% |8.2.1.2 |b|| | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits 0.83% |8.2.1.2 |b|| | 1 |
| Engine MIL inoperative or indicates a malfunction not illuminated |8.2.1.2 |h|| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure stud broken holding bracket to subframe |5.3.3 |a| |i|| | 1 |
| Nearside Outer Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings sill panel |6.1.B.2| | 1 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill panel and floor pan |6.1.B.2| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill panel and floor pan |6.1.B.2| | 1 |
| Nearside Front Lower Anti-roll bar insecure |2.4.G.1| | 1 |
| Offside Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Rear Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.4.G.4e| | 1 |
| Nearside Rear Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail engine bay (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail engine bay (6.2.2 (d) (i)) | 1 |
| Emissions not tested rear of exhaust not connect to the system |7.3.A.1| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis rail (5.3.3 (b) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis rail (5.3.3 (b) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced lower sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
| Nearside Steering system lock to lock check twists a brake pipe |2.2.D.2b| | 1 |
| Offside Front Shock absorber has negligible damping effect |2.7.5| | 1 |
| Nearside Front Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Seat belt anchorage prescribed area is excessively corroded both rear outer sills |5.2.6| | 1 |
| Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Inner Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Brake pipe leaking full length pipe |3.6.A.1| | 1 |
| Rear Brake pipe leaking on a hydraulic braking system chalked up |1.1.11 |b| |ii|| | 1 |
| Offside Body panel corroded and likely to cause injury inner ,faceing panel (6.2.1 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded underside of chassis rail beside sub-frame mounting |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded underside of chassis rail beside sub-frame mounting |2.4.A.3| | 1 |
| Front Suspension component mounting prescribed area is inadequately repaired both front chassis |2.4.A.3| | 1 |
| Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings both chassis |6.1.B.2| | 1 |
| Power steering component|s| leaking possible rack |2.3.3b| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint likely to become detached ( is detached ) (5.3.4 (a) (ii)) | 1 |
| Offside Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Nearside Rear Inner Road wheel badly distorted (5.2.2 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner arch/sill marked with yellow paint (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail behind brake pipes marked with yellow paint (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Upper Arch Area (6.2.2 (d) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail in front of subframe excessively corroded (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill excessively corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch excessively corroded (5.3.6 (a) (i)) | 1 |
| Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Emissions unable to be completed exhaust leak (8.2.2.2 (e)) | 1 |
| Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded anti roll mounting |2.2.C.1h| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer sill will require trim |5.2.6| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Shock absorbers has an excessively worn bush shocker lower bush |5.3.2 |c|| | 1 |
| Nearside Front Shock absorbers has an excessively worn bush lower bush |5.3.2 |c|| | 1 |
| Nearside Front Brake valve leaking caliper |1.1.7 |d| |i|| | 1 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover missing |5.3.4 |b| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength hole in floor near seat mounting |5.2.6| | 1 |
| Fuel system component insecure fuel filter |7.2.1| | 1 |
| Exhaust has a major leak of exhaust gases centre pipe |7.1.2| | 1 |
| Exhaust has a major leak of exhaust gases back pipe joint |7.1.2| | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 1 |
| Body has excessive displacement which may lead to loss of vehicle control |6.1.B.1a| | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Body has a sharp edge caused by corrosion front and rear wheel arches |6.1.C.1| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings NEARSIDE AND OFFSIDE INNER SILLS |6.1.B.2| | 1 |
| Front suspension has excessive movement at a tie bar joint OFFSIDE FRONT DROP-LINK SNAPPED |2.5.A.1c| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded by arch |5.2.6| | 1 |
| Front Headlamp aim projected beam image is obviously incorrect ns/os |4.1.2 |c|| | 1 |
| Seat belt anchorage prescribed area is excessively corroded both inner sills |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill
|5.2.6| | 1 |
| Offside Outer Rear Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded and outer sill to floor |5.2.6| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill/floor |5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases Centre to back box (6.1.2 (a)) | 1 |
| Offside Rear Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint excessively worn bottom ball joint (5.3.4 (a) (i)) | 1 |
| Offside Front Brake pipe leaking to rear |3.6.A.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg |6.1.A.1| | 1 |
| Steering column universal joint has excessive wear or play joint under bonnet (2.2.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect european headlight (4.1.2 (c)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp are incorrectly positioned (4.1.4 (a)) | 1 |
| Nearside Front Braking system leaking brake caliper hose connection |3.6.A.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Braking system leaking Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Service brake excessively binding (1.2.1 (f)) | 1 |
| Central Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Offside Rear Bonded suspension unit bonding failed and part of unit is likely to become displaced |2.4.F.2| | 1 |
| Stop lamp(s) not working hi level (4.3.1 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases SILENCER |7.1.2| | 1 |
| Nearside Front Road wheel cracked |4.2.A.1a| | 1 |
| Offside Rear Road wheel fractured |4.2.B.1a| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Emission control equipment missing where fitted as standard Evap Canister , missing from offside inner arch (8.2.1.1 (a)) | 1 |
| Nearside Front Upper Suspension arm insecurely attached ball joint loose (5.3.3 (a) (i)) | 1 |
| Offside Rear Lower Anti-roll bar linkage insecurely attached ball joint loose (5.3.3 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.63 (8.2.1.2 (b)) | 1 |
| Side repeater light intensity significantly reduced (4.4.3 (a)) | 1 |
| Nearside Rear Passenger`s seat insecure |6.2.A.1| | 1 |
| Exhaust has a major leak of exhaust gases centre to rear joint |7.1.2| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced nearside rear inner sill (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear exhaust broken (6.1.2 (a)) | 1 |
| Rear Road wheel fixing missing both (5.2.1 (a) (i)) | 1 |
| Emissions not tested rear silencer broken (8.2.1.2 (d)) | 1 |
| Nearside Rear Upper Trailing arm attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Headlamp not working on main beam Both. |1.7.5a| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion wheel arch. |6.1.C.1| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion Wheel arch. |6.1.C.1| | 1 |
| Nearside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings Outer sill |prescribed area|. |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings Sill |prescribed area|. |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings Onner wheel arch |prescribed area|. |6.1.B.2| | 1 |
| Nearside Front Headlamp aim so that beam "kick up" is not visible on the screen no beam pattern |4.1.2 |a|| | 1 |
| Offside Front Headlamp aim so that beam "kick up" is not visible on the screen no beam pattern |4.1.2 |a|| | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill area |6.1.1 |c| |i|| | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill area |6.1.1 |c| |i|| | 1 |
| Offside Floor excessively deteriorated MIDDLE FLOOR HOLED AND CORRODED |6.2.4 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail anti roll bar. (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail anti roll bar. (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Offside Headlamp not working on main beam bad earth issue (4.1.1 (a) (ii)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill/ arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer and inner sill |6.1.B.2| | 1 |
| Nearside Front Anti-roll bar missing drop link |2.4.G.1| | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill |6.2.2 |d| |ii|| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings offside rear inner sill holed and corroded |6.1.B.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced excessively corroded within 30 cms of mountimg |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced excessively corroded within 30 cms of mounting |7.1.1 |a| |i|| | 1 |
| Brake performance not tested could not be tested due to leaking brake pipe |1.2.1 |g|| | 1 |
| Nearside Rear Electrical wiring insecure and in contact with sharp edges Wiring in contact with suspension parts (4.11 (a) (ii)) | 1 |
| Offside Rear Electrical wiring insecure and in contact with sharp edges Wiring in contact with suspension parts (4.11 (a) (ii)) | 1 |
| Electrical wiring likely to touch hot or rotating parts Wiring from steering column fouling steering wheel (4.11 (a) (iii)) | 1 |
| Nearside Electrical wiring likely to drag on the ground (4.11 (a) (iii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel arch (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre to rear |7.1.2| | 1 |
| Seat belt anchorage prescribed area is excessively corroded offside rear inner sill |5.2.6| | 1 |
| Brake fluid contaminated |1.8 |a|| | 1 |
| Rear Exhaust has a major leak of exhaust gases exhaust joint (6.1.2 (a)) | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 1 |
| Front Shock absorbers damaged to the extent that it does not function |5.3.2 |b|| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering Nearside and offside rear sills (6.1.1 (c) (ii)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail at wishbone mounting |2.4.A.3| | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect lens |4.1.2 |c|| | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect lens |4.1.2 |c|| | 1 |
| Rear Service brake excessively fluctuating Both sides (1.2.1 (e)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Behind wheel (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Behind wheel (6.2.2 (d) (i)) | 1 |
| Nearside Rear Brake valve leaking (1.1.7 (d) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired centre outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill centre (7.1.1 (a) (i)) | 1 |
| Nearside Rear Brake hose leaking INTO CALIPER FROM JUNCTION BOX |3.6.A.1| | 1 |
| Nearside Front Upper Suspension arm locating pin insecure |2.4.G.3a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/roll bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Parking brake inoperative on one side readings N/S/R 9
O/S/R 104 (1.4.1 (a)) | 1 |
| Nearside Inner Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush broken |2.4.G.2| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front and rear |6.1.1 |c| |i|| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front and rear |6.1.1 |c| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis member (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced N/S Sill excessively corroded |6.1.1 |c| |i|| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced O/F Sill excessively corroded |6.1.1 |c| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired Inside inner wheel arch patch screwed on (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired Inside inner wheel arch patch screwed on (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired Front floor pan patch not welded on (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired Patch not welded in place inner sill/floor (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill/floor corroded/holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch corroded/holed (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wing corroded/holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp light source and lamp not compatible Non halogen bulbs fitted (4.1.4 (c)) | 1 |
| Offside Front Headlamp light source and lamp not compatible Non halogen bulbs fitted (4.1.4 (c)) | 1 |
| Nearside Front Headlamp not working on main beam Does not operate when dipped beam is on. (4.1.1 (a) (ii)) | 1 |
| Offside Front Anti-roll bar linkage damaged and seriously weakened |5.3.3 |b| |i|| | 1 |
| Exhaust has a major leak of exhaust gases mid section and rear section flange excessively corroded causing to leak |6.1.2 |a|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill excessively corroded |7.1.1 |a| |i|| | 1 |
| Centre Seat belt anchorage prescribed area is excessively corroded nearside offside floor |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner and outer sill at jacking point + closing plate (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill at rear jacking point (7.1.1 (a) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn D bushes (5.3.4 (a) (i)) | 1 |
| Rear Brake disc significantly and obviously worn primarily N/S (1.1.14 (a) (i)) | 1 |
| Front Electrical wiring insulation so damaged or deteriorated it is likely to cause a short-circuit headlight wiring both sides connectors not suitable and insulation inadequate (4.11 (c) (ii)) | 1 |
| Nearside Front Hydraulic fluid leaking continuously posing a serious risk to road safety severe brake fluid leak calliper area.... (8.4.1 (a) (ii)) | 1 |
| Nearside Front Lower Suspension component ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases joint area.... (6.1.2 (a)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits to high aprox 0.655 (8.2.1.2 (a)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits aprox 0.573 (8.2.1.2 (b)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.114 (8.2.1.2 (c)) | 1 |
| Nearside Front Upper Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced body sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced body sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced body sill (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced under wing (6.1.1 (c) (i)) | 1 |
| Nearside Rear Exhaust emissions likely to be affected by an induction leak (8.2.1.1 (b)) | 1 |
| Offside front brake binding unable to check wheel bearing |3.7.B.1| | 1 |
| Offside Front Wheel nut|s| loose |4.2.A.1e| | 1 |
| Nearside Rear Wheel stud hole elongated |4.2.A.1d| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill end |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Outer sill end |5.2.6| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is fractured damage to box section
|2.4.A.3| | 1 |
| Offside Front position lamp|s| insecure |1.1.A.3a| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis as marked (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength offside & nearside outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Body component insecure (6.2.1 (a) (i)) | 1 |
| Front rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Floor excessively deteriorated under vehicle (6.2.4 (a) (i)) | 1 |
| Offside Front Floor excessively deteriorated under vehicle (6.2.4 (a) (i)) | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded Chassis rail holed next to spring |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded Chassis rail holed next to spring |2.4.A.3| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint snapped |2.4.G.2| | 1 |
| Offside Rear Macpherson strut likely to fail (5.3.3 (b) (ii)) | 1 |
| Brake pipe at imminent risk of failure or fracture front to rear (1.1.11 (a)) | 1 |
| Nearside Front Suspension rod ball joint excessively worn Drop link ball joint (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension rod ball joint excessively worn Drop link ball joint (5.3.4 (a) (i)) | 1 |
| Nearside Rear Suspension rod ball joint excessively worn Drop link ball joint (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension rod ball joint excessively worn Drop link ball joint (5.3.4 (a) (i)) | 1 |
| Nearside Rear Outer Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Offside Rear Outer Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint likely to become detached Re-Secure ball joint locking nut |5.3.4 |a| |ii|| | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases tailpipe/silencer area |7.1.2| | 1 |
| Central Rear Brake pipe leaking on a hydraulic braking system burst while driving car onto ramp (1.1.11 (b) (ii)) | 1 |
| Brake performance unable to be tested due to brake pipes leaking (1.2.1 (g)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis has hole in it (inner wheel arch) (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis has hole in it(inner wheel arch0 (6.1.1 (c) (i)) | 1 |
| Central Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under car chassis has hole in it (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill has hole in it close to seat belt mount (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner brake disc in such a condition that it is seriously weakened |3.5.1i| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer Cill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Front Driver`s seat fore and aft adjustment mechanism not functioning as intended. |6.2.5 |b| |i|| | 1 |
| Front Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction wipper sun strip[ |3.1 |a| |ii|| | 1 |
| Front Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction |3.1 |a| |ii|| | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced marked yellow |6.1.1 |c| |i|| | 1 |
| Rear Service brake effort inadequate at a wheel both |1.2.1 |a| |i|| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail holed . side and underneath . (5.3.6 (a) (i)) | 1 |
| Offside Position lamp not working |4.2.1 |a| |ii|| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened CHASSIS RAIL. (5.3.3 (b) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn link (5.3.4 (a) (i)) | 1 |
| Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wing (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength bay (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength bay (5.3.6 (a) (i)) | 1 |
| Battery insecure and likely to fall from carrier tray corroded (4.13 (a) (ii)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Rear Brake linkage has restricted free movement caliper arm |3.5.1k| | 1 |
| Nearside Direction indicator flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced both |4.1.4 |b|| | 1 |
| Offside Rear Body component corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Offside Rear All direction indicators incorrect colour (4.4.3 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Centre Stop lamp adversely affected by the operation of another lamp foglamp |1.2.1f| | 1 |
| Offside Front Electrical wiring inadequately supported |1.9.2a| | 1 |
| Nearside Front Electrical wiring inadequately supported |1.9.2a| | 1 |
| Offside Front Anti-roll bar linkage insecurely attached ball joint detached (5.3.3 (a) (i)) | 1 |
| Stop lamp(s) switch with a delay in operation (4.3.2 (a) (ii)) | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s/f and o/s/f |6.1.B.2| | 1 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sills |6.1.B.2| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sills |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inside wheel arch |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inside wheel arch |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Chassis |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis rail |6.1.1 |c| |ii|| | 1 |
| Headlamp insecure both |4.1.1 |c|| | 1 |
| Bonnet primary retaining device excessively deteriorated safety catch faulty |3.1 |c|| | 1 |
| Suspension component ball joint likely to become detached split pins missing from both top balljoints |5.3.4 |a| |ii|| | 1 |
| Brake pipe likely to become detached or damaged brake and fuel lines loose along floor |1.1.11 |d| |ii|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills |7.1.1 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill holed |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded floor holed |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis leg two holes |2.4.A.3| | 1 |
| Nearside Outer Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings OSF floor beside subrame |6.1.B.2| | 1 |
| Rear Sub-frame insecure Brace |2.4.G.1| | 1 |
| Nearside Rear Suspension arm has excessive play in a pin/bush Front Bush |2.4.G.2| | 1 |
| Offside Rear Suspension arm has excessive play in a pin/bush Front Bush |2.4.G.2| | 1 |
| Nearside Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Nearside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Offside Rear Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Nearside Direction indicator missing |4.4.1 |a| |ii|| | 1 |
| Hazard warning switch inoperative |4.4.2 |a| |ii|| | 1 |
| Nearside Body component damaged and likely to cause injury Door |6.2.1 |a| |i|| | 1 |
| Driver`s seat with a defective structure |6.2.5 |a| |i|| | 1 |
| Passenger`s seat with a defective structure |6.2.6 |a| |i|| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect no patton |1.8.A.1b| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner floor to sill |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner floor to sill |5.2.6| | 1 |
| Offside Front Driver`s door hinge deteriorated so the door cannot be readily opened or closed will not open from inside |6.2.B.2| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor (7.1.1 (a) (i)) | 1 |
| Offside Front Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner door sill |6.1.B.2| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced footwell/inner sill |7.1.1 |a| |i|| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced footwell/inner sill |7.1.1 |a| |i|| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor |7.1.1 |a| |i|| | 1 |
| Offside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced at antiroll bar mount |6.1.1 |c| |i|| | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner/outer sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner/outer sill |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner sill/floor |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill/floor |2.4.A.3| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Front Body panel damaged and likely to cause injury wing (6.2.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail at anti roll bar (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail at anti roll bar (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases center to rear exhaust box |7.1.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill holed and corroded |5.2.6| | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill. (6.1.1 (c) (i)) | 1 |
| Inner Rear Upper Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Additional braking device contacts insecure |3.6.I.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill |7.1.1 |a| |i|| | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill. (6.1.1 (c) (i)) | 1 |
| Centre Exhaust has a major leak of exhaust gases section resealed |7.1.2| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rear of outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded and inner sills |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded and inner sills |2.4.A.3| | 1 |
| Emissions not tested engine getting hot |7.3.A.1| | 1 |
| Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Suspension component ball joint dust cover no longer prevents the ingress of dirt both front top (5.3.4 (b) (ii)) | 1 |
| Exhaust emissions hydrocarbon content excessive engine missfire |7.3.B.1b| | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced front and rear outer sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded floor too sill |2.4.A.3| | 1 |
| Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced BOTH REAR INNER SILLS CORRODED (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor corroded (hole) (7.1.1 (a) (i)) | 1 |
| Nearside Rear Lower Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside front brakes release unevenly |3.7.B.4| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill x2 (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill holed (6.2.2 (d) (ii)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting nut missing |2.4.G.1| | 1 |
| Emissions not tested blowing on cat flange (8.2.1.2 (d)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting rear wheel arch to chassis heavily corroded (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch heavily corroded with sharpe edges (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor heavily corroded under drivers seat (6.1.1 (c) (i)) | 1 |
| Rear Anti-roll bar linkage pin or bush excessively worn both very weak corroded away (5.3.4 (a) (i)) | 1 |
| Offside Front Brake performance unable to be tested binding very badly wheel too hot to touch (1.2.1 (g)) | 1 |
| Rear Brake disc significantly and obviously worn both sets as vehicle has been stood (1.1.14 (a) (i)) | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced no pattern |1.7.5a| | 1 |
| Offside Rear Lower Suspension arm damaged and seriously weakened has been opened up to gain access into shocker bolt |2.4.G.1| | 1 |
| Subframe mounting prescribed area is excessively corroded nearside front chassis leg, inner wheel arch area |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area is excessively corroded offside middle chassis leg |5.2.6| | 1 |
| Horn not working button missing (7.7 (a)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch, marked in yellow (5.3.6 (a) (i)) | 1 |
| Central Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 1 |
| Nearside Front Front position lamp|s| obscured more than 50% |1.1.A.3c| | 1 |
| Drive belt excessively worn (6.1.7 (c) (i)) | 1 |
| Body insecure and dangerous to other road users both sill covers bonding failed at front |6.1.B.1b| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill / inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor corroded 3 holes (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg by front anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded bottom of sill area |5.2.6| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded under wheel arch chassis area |2.4.A.3| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded under wheel arch chassis area |2.4.A.3| | 1 |
| Offside Front Driver`s door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Offside Front Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Offside Rear Brake pipe seriously damaged |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Upper Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
| Upper Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` both sides |8.3.1e| | 1 |
| Central Lower Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Offside Front Electrical wiring insecure abs loom |1.9.2a| | 1 |
| Offside Rear Anti-lock braking system component excessively damaged absr ing gear |3.4.2| | 1 |
| Offside Outer Vehicle structure has excessive corrosion which adversely affects braking or steering central chassis x two |6.1.A.1| | 1 |
| Driver`s view of an obligatory external mirror materially affected by an obstruction |3.1 |a| |ii|| | 1 |
| Central Rear Exhaust system insecure |6.1.2 |a|| | 1 |
| Offside Rear Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Braking system leaking calliper |3.6.A.1| | 1 |
| Nearside Front Lower Macpherson strut pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Headlamp aim so that beam "kick up" is not visible on the screen poor image |4.1.2 |a|| | 1 |
| Offside Front Headlamp aim so that beam "kick up" is not visible on the screen poor image |4.1.2 |a|| | 1 |
| Nearside Front Body panel corroded and likely to cause injury wheel arch |6.2.1 |a| |i|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill |6.2.2 |d| |i|| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis at suspension |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis at suspension |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg at front to rear brake pipes |6.1.B.2| | 1 |
| Nearside Front Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
| Rear Exhaust has a major leak of exhaust gases rear exhaust join. (6.1.2 (a)) | 1 |
| Nearside Front Anti-roll bar insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Position lamp not working both front (4.2.1 (a) (ii)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill by seat mounting which has seat connected |7.1.1 |a| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded Floor to sill |5.2.6| | 1 |
| Offside Brake hose leaking |3.6.A.1| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded rear sill |5.2.6| | 1 |
| Brake performance not tested due to fluid leaks |1.2.1 |g|| | 1 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill/floor pan (6.2.2 (d) (i)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sills (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Suspension arm fractured (5.3.3 (b) (ii)) | 1 |
| Offside Front Shock absorbers likely to become detached (5.3.2 (a) (ii)) | 1 |
| Nearside Front Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Brake hydraulic reservoir fluid not visible (1.1.10 (d) (iii)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded box section n/s/r/sill/pannelling |5.2.6| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill to floor |6.1.B.2| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor corroded within 30cm of seat mount (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor corroded within 30cm of seat mount (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded under wheel arch |2.4.A.3| | 1 |
| Nearside Outer Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill area (7.1.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure (5.3.3 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail in front of subframe/roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced lower floor holed and corroded |7.1.1 |a| |i|| | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill/ both side (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases tail pipe to centre pipe (6.1.2 (a)) | 1 |
| Nearside Front Headlamp aim so that beam "kick up" is not visible on the screen No beam Patten |4.1.2 |a|| | 1 |
| Offside Front Headlamp aim so that beam "kick up" is not visible on the screen No beam Patten |4.1.2 |a|| | 1 |
| Offside Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Front Brake hose excessively twisted during lock to lock check |1.1.12 |b| |ii|| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition rear exhaust section missing where fitted as standard |7.1.4| | 1 |
| Suspension component mounting prescribed area is excessively corroded both front chassis rails / inner flitches |2.4.A.3| | 1 |
| Emissions not tested engine overheated (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer sills |5.2.6| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded arm |2.4.A.3| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Emissions not tested NO READING DUE TO CONDITION OF EXHAUST (8.2.1.2 (d)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced INNER OUTER SILLS (7.1.1 (a) (i)) | 1 |
| Offside Rear Anti-roll bar ball joint excessively worn BROKEN (5.3.4 (a) (i)) | 1 |
| Emissions not tested major exhaust blow (8.2.1.2 (d)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill x 2 (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill backing/ floor to sill (7.1.1 (a) (i)) | 1 |
| Rear Brake disc contaminated |1.1.14 |b|| | 1 |
| Nearside Inner Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively damaged significantly reducing structural strength under sill at rear (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively damaged significantly reducing structural strength under sill at rear (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced undersill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced central outer sill holed (7.1.1 (a) (i)) | 1 |
| Front Drivers airbag obviously inoperative Light indicates a fault (7.1.5 (c)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill end cap (6.1.1 (c) (i)) | 1 |
| Offside Front Brake pipe leaking on a hydraulic braking system to rear pipe (1.1.11 (b) (ii)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 1 |
| Offside Front Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded arch |5.2.6| | 1 |
| Nearside Front Anti-roll bar insecure broken |2.4.G.1| | 1 |
| Headlamp excessively deteriorated so that the light output is severely reduced Both |1.7.5a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis various |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis various |5.3.6 |a| |i|| | 1 |
| Offside Parking brake inoperative on one side only making 20kg performance |1.4.1 |a|| | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill rotted within 30cm of seat mount |7.1.1 |a| |i|| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill rotted within 30cm of seat mount |7.1.1 |a| |i|| | 1 |
| Nearside Rear rear brakes release unevenly |3.7.B.4| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded central under sill corroed |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill
|2.4.A.3| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.3 |a|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak various leaks in exhaust system (8.2.1.1 (b)) | 1 |
| Rear Prop shaft securing bolt missing (6.1.7 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch area, marked yellow (6.1.1 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced No beam pattern |1.7.5a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Excessive corrosion/holes to chassis leg/inner wheel arch panel |2.4.A.3| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill and wheel arch areas |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill and wheel arch areas |5.2.6| | 1 |
| Front Brake valve leaking such that brake functionality is affected |1.1.7 |d| |ii|| | 1 |
| Brake master cylinder leaking |1.1.10 |b| |ii|| | 1 |
| Nearside Tie bar/rod attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor as marked |6.1.1 |c| |i|| | 1 |
| Nearside Front Vehicle structure has a fracture which adversely affects braking or steering Above roll bar mount |6.1.A.1| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Full sill |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Full sill |5.2.6| | 1 |
| Floor excessively deteriorated O/S AND N/S FRONT CORDED FROM WHEEL ARCH TO FLOOR OUTER EDGE. |6.2.4 |a| |i|| | 1 |
| Suspension arm corroded and seriously weakened O/S AND N/S REAR UPPER WISH BONE CORRODED. |5.3.3 |b| |i|| | 1 |
| Nearside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Coil spring mounting loose |2.4.C.3a| | 1 |
| Nearside Front Lower Front suspension locking device missing |2.5.A.4| | 1 |
| Rear fog lamp switch faulty Fog lamp illuminated with the operation of position lamps |1.3.1a| | 1 |
| Nearside Rear Lower Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Service brake indicates brake bind |3.7.D.2a| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced mid inner sill |7.1.1 |a| |i|| | 1 |
| Headlamp aim beam image obviously incorrect both |1.8.A.1b| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive 0.33 |7.3.D.3| | 1 |
| Nearside Lower Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded rear outer sill panel |5.2.6| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings body sill |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings shocker mount |6.1.B.2| | 1 |
| Centre Seat belt anchorage prescribed area is excessively corroded chassis both sides |5.2.6| | 1 |
| Nearside Outer Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Rear Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis rail (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor holed |7.1.1 |a| |i|| | 1 |
| Front Brake disc significantly and obviously worn inner faces corroded (1.1.14 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area fractured significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
| Brake hose leaking on a hydraulic braking system offside front brake pipe to ferrel (1.1.12 (c) (ii)) | 1 |
| Headlamp light intensity severely reduced dip beam (4.1.4 (a)) | 1 |
| Headlamp light intensity severely reduced main beam (4.1.4 (a)) | 1 |
| Front Power steering pump leaking |2.1.5 |a|| | 1 |
| Offside Front Vehicle structure is fractured and structural rigidity is significantly reduced marked area |6.1.1 |a| |i|| | 1 |
| Nearside Front Lower Macpherson strut insecure |2.4.G.1| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner chassis leg |2.4.A.3| | 1 |
| Brake pipe leaking front to rear brake pipe |3.6.A.1| | 1 |
| Offside Rear Shock absorber insecure top mount |2.7.2b| | 1 |
| Offside Front Driver`s seat insecure |6.2.A.1| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor section |5.2.6| | 1 |
| Offside Rear Outer Steering component mounting prescribed area is excessively corroded sill area holed (2.1.2 (e) (i)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction Stickers on windscreen (3.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail |6.1.B.2| | 1 |
| Offside Rear Integral body structure has excessive corrosion which adversely affects braking or steering Outer sill to rear (6.1.1 (c) (ii)) | 1 |
| Offside Rear Integral body structure has excessive corrosion which adversely affects braking or steering Sill underbody at rear (6.1.1 (c) (ii)) | 1 |
| Offside Integral body structure modified such that it is likely to adversely affect braking or steering Floor pan to sill holed and corroded (6.1.1 (d) (ii)) | 1 |
| Rear Exhaust system insecure Silencer to centre pipe corroded & broken bolt (6.1.2 (a)) | 1 |
| Nearside Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Nearside Rear Exhaust emissions likely to be affected by an exhaust leak back box flange (8.2.1.1 (b)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Suspension component mounting prescribed area excessively damaged significantly reducing structural strength both front chassis rails (5.3.6 (a) (i)) | 1 |
| Offside Anti-roll bar has excessive play in a ball joint front and rear |2.4.G.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassy |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill back |6.1.B.2| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Front Brake performance not tested |1.2.1 |g|| | 1 |
| Rear Brake performance not tested |1.2.1 |g|| | 1 |
| Hydraulic brake cylinder leaking hydraulic fluid |1.1.16 |b| |i|| | 1 |
| Nearside Front Anti-roll bar linkage damaged and seriously weakened |5.3.3 |b| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis as marked (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired CHASSIE LEG (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced A PILLAR (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced JACKING POINT (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength behind wheel |floor| |5.3.6 |a| |i|| | 1 |
| Nearside Front Power steering component leaking rack end |2.1.5 |a|| | 1 |
| Offside Outer Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded shocker absorber mounting corroded where it attatches to lower suspension arm |2.4.A.3| | 1 |
| Nearside Front Brake hose excessively twisted rubbing wheel on full lock |1.1.12 |b| |ii|| | 1 |
| Offside Rear Brake pipe leaking on an air braking system main by clip |1.1.11 |b| |i|| | 1 |
| Nearside Headlamp aim does not move downwards when dipped |British American headlamp| |1.8.C.4| | 1 |
| Nearside Front Tie bar/rod rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar severely distorted |2.4.G.1| | 1 |
| Offside Rear Anti-roll bar severely distorted |2.4.G.1| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded inner sill floor pan area |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis next to anti roll bar mounting and subframe mounting |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded next to anti roll bar mounting and subframe mounting |2.4.A.3| | 1 |
| Inner Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner and outer sill |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded center inner sill |5.2.6| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch |5.3.6 |a| |i|| | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Lower Seat belt installation lower anchorages less than 320mm apart sill/ floor section holed (10.1 (k)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg |6.1.1 |c| |i|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WHEEL ARCH (5.3.6 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SILL (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WHEEL ARCH (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Upper Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen no pattern |4.1.2 |a|| | 1 |
| Offside Front Headlamp aim so that beam "kick up" is not visible on the screen no pattern |4.1.2 |a|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg inside wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg inside wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Rear Vehicle structure is fractured and structural rigidity is significantly reduced outer sill corroded and holed |6.1.1 |a| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill corroded and holed |6.1.1 |c| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor/jacking mount corroded and holed |6.1.1 |c| |i|| | 1 |
| Offside Rear Upper Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch |7.1.1 |a| |i|| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Body has a sharp edge caused by damage door |6.1.C.1| | 1 |
| Front Upper Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt both |2.4.G.2| | 1 |
| Offside Rear Subframe mounting prescribed area is fractured |2.4.A.3| | 1 |
| Nearside Rear Body component corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Rear brake disc modified and seriously weakened |3.5.1n| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings rear of outer sill corosion/ hole |6.1.B.2| | 1 |
| Steering column locking device missing |2.1.6| | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Suspension component mounting prescribed area is excessively corroded nearside rear outer sill |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength front mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp light source and lamp not compatible led fitted/ no pattern (4.1.4 (c)) | 1 |
| Offside Front Headlamp light source and lamp not compatible led fitted no pattern (4.1.4 (c)) | 1 |
| Nearside Headlamp aim beam image obviously incorrect bulb refitted |1.8.A.1b| | 1 |
| Offside Headlamp aim beam image kick up to the offside deflector fitted |1.8| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner + outer seals |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Quarter pannel |5.2.6| | 1 |
| Front Front position lamp|s| not working both |1.1.A.3b| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded 30cm within drivers front seat mount |5.2.6| | 1 |
| Offside Floor excessively deteriorated Holed within 30 cm drivers seat mounting. (6.2.4 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill corroded from wheel arch. (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure is fractured and structural rigidity is significantly reduced Sill. (6.1.1 (a) (i)) | 1 |
| Rear Brake disc significantly and obviously worn Both rear discs. (1.1.14 (a) (i)) | 1 |
| Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt Both front upper arm outer ball joint covers. (5.3.4 (b) (ii)) | 1 |
| Rear Brake pipe leaking on a hydraulic braking system at union on offside (1.1.11 (b) (ii)) | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer seal rust hole |6.1.B.2| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded near wishbone |2.4.A.3| | 1 |
| Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Fuel cap/sealing device missing cap missing (6.1.3 (b) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced lower wheel arch corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded |7.1.1 |a| |i|| | 1 |
| Front Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill (6.2.2 (d) (ii)) | 1 |
| Offside Front Outer Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill (6.2.2 (d) (ii)) | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings SILL |6.1.B.2| | 1 |
| Offside Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting cill corroded (6.2.2 (d) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.80 (8.2.1.2 (b)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.082 (8.2.1.2 (c)) | 1 |
| Rear Anti-roll bar insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor (6.2.2 (d) (i)) | 1 |
| Front Power steering component|s| leaking Steering rack |2.3.3b| | 1 |
| Front Headlamp aim beam image obviously incorrect both fronts |1.8.A.1b| | 1 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chalked |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chalked area |6.1.B.2| | 1 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chalked |6.1.B.2| | 1 |
| Nearside Rear Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg holed (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Upper coil spring cracked |2.4.C.1a| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis leg (6.2.2 (d) (i)) | 1 |
| Nearside Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Offside Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases fumes coming in to car |7.1.2| | 1 |
| Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Outer Stop lamp not working |1.2.1b| | 1 |
| Electrical wiring deteriorated and bare connector exposed |1.9.2c| | 1 |
| Central Exhaust has a major leak of exhaust gases joint between centre section and cat flange |7.1.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill section/qtr panel holed |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill section/QTR panel |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded inner floor section holed |5.2.6| | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt Split |5.3.4 |b| |ii|| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings full sill |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings full sill |6.1.B.2| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded box section |2.4.A.3| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded box section |2.4.A.3| | 1 |
| Stop lamp(s) not working 3rd (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner/outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner/outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Central Exhaust has a major leak of exhaust gases on joint (6.1.2 (a)) | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Nearside Front Headlamp light source and lamp not compatible LED (4.1.4 (c)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch at front (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch at front (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected subframe mount (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected subframe mount (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch upper (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill seat mount (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced door step seat belt mount (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner Sill |6.1.B.2| | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |centre| |6.1.1 |c| |i|| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer |7.1.1 |a| |i|| | 1 |
| Offside Front position lamp|s| not working main |1.1.A.3b| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill x2 |6.1.B.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded x2 |5.2.6| | 1 |
| Offside Rear Service brake indicates brake bind |3.7.D.2a| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced undersill (7.1.1 (a) (i)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected chassis earth lead (4.11 (a) (ii)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar linkage insecure and impairing directional stability Drop link not attached (5.3.3 (a) (ii)) | 1 |
| Offside Rear Brake pipe leaking T piece |3.6.A.1| | 1 |
| Front Hydraulic brake calliper damaged and braking performance affected |1.1.16 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis Leg |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis Leg |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak Rear Exhaust Box |8.2.1.1 |b|| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor holed (6.1.1 (c) (i)) | 1 |
| Brake disc significantly and obviously worn both rear |1.1.14 |a| |i|| | 1 |
| Brake performance unable to be tested BRAKE PIPE LEAKING. (1.2.1 (g)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL. (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL, (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension arm attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Brake performance not tested due to brake pipes |1.2.1 |g|| | 1 |
| Nearside Front Upper Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Front Upper Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Nearside Front Inner Suspension arm insecurely attached |5.3.3 |a| |i|| | 1 |
| Nearside Front Vehicle structure has a fracture which is likely to adversely affect braking or steering |6.1.1 |a| |ii|| | 1 |
| Offside Front Vehicle structure has a fracture which is likely to adversely affect braking or steering |6.1.1 |a| |ii|| | 1 |
| Anti-roll bar has excessive play in a ball joint o/s/r |2.4.G.2| | 1 |
| Front Drivers view of the road through the swept area of the windscreen materially affected by an obstruction (3.1 (a) (ii)) | 1 |
| Anti-lock braking system warning lamp is missing. |3.4.1a| | 1 |
| Nearside Front Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner Sill |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced |Outer sill| |7.1.1 |a| |i|| | 1 |
| Offside Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength as marked on body rail (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength as marked on body rail (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill as marked (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion outer sill as marked (7.1.1 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion out sill as marked (7.1.1 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded Inner wing |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Anti-roll bar mounting.Inner wing |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Upper suspension arm .Inner wing |2.4.A.3| | 1 |
| Nearside Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 1 |
| Nearside Power steering pipe|s| or hose|s| leaking due to excessive corrosion |2.3.3b| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 1 |
| Central Upper Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached broken |5.3.4 |a| |ii|| | 1 |
| Nearside Upper Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 1 |
| Central Front Exhaust emissions likely to be affected by an exhaust leak |8.2.2.1 |b|| | 1 |
| Central Front Exhaust emissions likely to be affected by an exhaust leak middle joining pipe has not fixing |8.2.2.1 |b|| | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak Back box has exhaust leek |8.2.2.1 |b|| | 1 |
| Central Front Fuel system component leaking |6.1.3 |b| |i|| | 1 |
| Emissions not tested due to fuel leek from engine the emitions could not be tested |8.2.1.2 |d|| | 1 |
| Fluid leak harmful to the environment or a risk to other road users |8.4.1 |a| |i|| | 1 |
| Emissions not tested severe misfire |7.3.A.1| | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn loose (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch under arch (5.3.6 (a) (i)) | 1 |
| Central Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s inner sill (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed due to misfire (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Sill
|5.2.6| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
| Nearside Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
| Emissions not tested car likely to over heat no alt belt fiited
alternator siezed |8.2.1.2 |d|| | 1 |
| Rear Seat belt anchorage prescribed area is excessively corroded both arches |5.2.6| | 1 |
| Rear Seat belt anchorage prescribed area is excessively corroded both outer sills |5.2.6| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint detached |2.4.G.2| | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis split both sides |6.1.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill backing |5.2.6| | 1 |
| Offside Front Body panel corroded and likely to cause injury Wheel Arch |6.2.1 |a| |i|| | 1 |
| Offside Rear Body panel corroded and likely to cause injury Wheel Arch |6.2.1 |a| |i|| | 1 |
| Nearside Rear Body panel corroded and likely to cause injury Wheel Arch |6.2.1 |a| |i|| | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering seat anchorage |6.1.A.1| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis holed & corroded. |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired Chassis. |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Offside Parking brake inoperative on one side excess travel. (1.4.1 (a)) | 1 |
| Offside Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt gaiter split |5.3.4 |b| |ii|| | 1 |
| Rear Brake performance not tested brakes worn to metal (1.2.1 (g)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt wishbone arm boot split |2.4.G.2| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive failed on two tests |7.3.D.3| | 1 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive failed on two tests |7.3.D.3| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits failed on two tests |7.3.D.3| | 1 |
| Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings rust hole in seal nearside rear lower |6.1.B.2| | 1 |
| Emissions not tested engine over heat |7.3.A.1| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded under sill |5.2.6| | 1 |
| Brake disc significantly and obviously worn Fronts |1.1.14 |a| |i|| | 1 |
| Brake disc significantly and obviously worn Rears |1.1.14 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases Rear |6.1.2 |a|| | 1 |
| Nearside Front Subframe mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected Chassis leg |5.3.6 |a| |ii|| | 1 |
| Offside Front Subframe mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected Chassis leg |5.3.6 |a| |ii|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill |5.3.6 |a| |i|| | 1 |
| Macpherson strut has an unsafe modification Suspension lowered ? Too low catches obstacles in road ? Eg traffic callers |5.3.3 |c| |i|| | 1 |
| Brake hose excessively twisted Both front, making contact with body/lower arm (1.1.12 (b) (ii)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis by front anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded by anti roll bar mounting |2.4.A.3| | 1 |
| Offside Front Side repeater likely to become detached (4.4.1 (c) (ii)) | 1 |
| Offside Rear fog lamp adversely affected by the operation of another lamp (4.5.4 (b)) | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Central Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings battery tray |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer |2.4.A.3| | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Sill (6.2.2 (d) (ii)) | 1 |
| Offside Rear Outer Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Sill (6.2.2 (d) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced INNER SILL / FLOOR (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced CHASSIS (7.1.1 (a) (i)) | 1 |
| Front Position lamp not working both sides (4.2.1 (a) (ii)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced cill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded arch |5.2.6| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint snapped |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded arb mount |2.4.A.3| | 1 |
| Offside Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired at front and rear (marked) (6.2.2 (d) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill holed |5.2.6| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Direction indicator obviously incorrectly positioned |1.4.A.2b| | 1 |
| Nearside Power steering component|s| leaking from a failed joint |2.3.3b| | 1 |
| Offside Power steering component|s| leaking from a failed joint |2.3.3b| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassie 2 holes |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced INNER ARCH (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced CHASSIS LEG (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area marked (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak test not done |8.2.1.1 |b|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch area |2.4.A.3| | 1 |
| Front Body has a projection caused by damage |6.1.C.1| | 1 |
| Offside Front Position lamp not working bulb and holder missing (4.2.1 (a) (ii)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect bulb loose in headlight (4.1.2 (c)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill closer |7.1.1 |a| |i|| | 1 |
| Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened |5.3.1 |b| |i|| | 1 |
| Central Front Undertray insecure (8.1.1 (b) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Silencer flange |6.1.2 |a|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner & outer sills, mid floor and front of rear wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill, mid floor & front of rear wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp light intensity severely reduced lense opaque (4.1.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced lense opaque (4.1.4 (a)) | 1 |
| Offside Rear Brake valve leaking caliper handbrake pivot (1.1.7 (d) (i)) | 1 |
| Service brake excessively binding Both front (1.2.1 (f)) | 1 |
| Exhaust catalytic converter obviously modified (8.2.2.1 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 1 |
| Nearside Front All position lamps have less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced BOTH SIDES (4.1.4 (b)) | 1 |
| Offside Rear Direction indicator lens defective such that the emitted light is adversely affected (4.4.1 (b) (ii)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Marked yellow |6.1.B.2| | 1 |
| Front Headlamp aim not tested |1.8.A.1c| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak rear pipe (8.2.1.1 (b)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill. |5.2.6| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill. |5.2.6| | 1 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint swivel. |2.5.B.1a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Anti roll bar mounting point to chassis corroded. (5.3.6 (a) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre chassis holed and corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength side frame (5.3.6 (a) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced centre floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill backing (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering COMPLETE BOX SECTION TOP BOTTOM AND SIDES |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering COMPLETE BOX SECTION TOP BOTTOM AND BOTH SIDES |6.1.A.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
| Nearside Front Power steering component|s| leaking from a failed joint |2.3.3b| | 1 |
| Nearside Rear Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases on joint (6.1.2 (a)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed in 2 places (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Outer Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill end |5.2.6| | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings marked |6.1.B.2| | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings marked |6.1.B.2| | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail. |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail. |5.3.6 |a| |i|| | 1 |
| Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction Sticker. |3.1 |a| |ii|| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive co very high .40 |7.3.D.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired floor pan ,seat mounting |5.2.6| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill inadequate repair |6.1.1 |c| |i|| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering wing |6.1.1 |c| |ii|| | 1 |
| Front Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Offside Front Lower Suspension component mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected spring cup |5.3.6 |a| |ii|| | 1 |
| Offside Front Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill. |7.1.1 |a| |i|| | 1 |
| Centre Rear Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Emissions not tested bad coolant leak |8.2.1.2 |d|| | 1 |
| Brake performance not tested coolant leak |1.2.1 |g|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Rear of sub-frame mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti roll bar mount |2.4.A.3| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded plus chassis rail |5.2.6| | 1 |
| Inner Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.A.1| | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.A.1| | 1 |
| Nearside Front Anti-roll bar linkage likely to become detached broken (5.3.3 (a) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases flexi pipe (6.1.2 (a)) | 1 |
| Drivers airbag obviously inoperative (7.1.5 (c)) | 1 |
| Nearside Rear Anti-roll bar linkage likely to become detached |5.3.3 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded lower wishbone |2.4.A.3| | 1 |
| Stop lamp not working both |1.2.1b| | 1 |
| Offside Front Vehicle structure has damage which adversely affects braking or steering chassis in engine bay |6.1.A.1| | 1 |
| Offside Inner Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Inner Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis on inner wheel arch |6.1.A.1| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases Front downpipe to cat (6.1.2 (a)) | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid CALIPER (1.1.16 (b) (i)) | 1 |
| Nearside Front Anti-roll bar linkage rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension arm ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg holed |2.4.A.3| | 1 |
| Offside Rear Upper Suspension arm corroded and seriously weakened holed |2.4.G.1| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill to arch |2.4.A.3| | 1 |
| Emissions not tested no back box to put pipe in |7.3.A.1| | 1 |
| Nearside Front position lamp|s| not working side |1.1.A.3b| | 1 |
| Offside Front position lamp|s| not working dip |1.1.A.3b| | 1 |
| Headlamp not working on main beam Appears to be an issue with dipped and main beam operation (4.1.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced osr inner wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Drivers airbag missing Steering wheel (7.1.5 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Outer sill panel |5.2.6| | 1 |
| Emissions not tested due to excessive smoke |8.2.1.2 |d|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills |5.3.6 |a| |i|| | 1 |
| Offside Seat belt retracting mechanism defective Locks while trying to pul out (7.1.2 (e)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment Appears cable is disconnected (1.1.6 (c)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting likely to become detached Secured with a g-clamp (5.3.3 (a) (ii)) | 1 |
| Horn sound not in accordance with requirements Claxon fitted (7.7 (c)) | 1 |
| Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill
|2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |coil spring area| |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill area |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill` |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg lower part |2.4.A.3| | 1 |
| Offside Front Lower Anti-roll bar attachment bracket modified and seriously weakened on suspension arm |2.4.A.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded boot floor |2.4.A.3| | 1 |
| Nearside Front passenger door catch insecure |6.2.B.2| | 1 |
| Undertray likely to become detached rubbing on rack boot (6.2.1 (a) (ii)) | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill ,split away from panel and corroded |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer body sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill section (7.1.1 (a) (i)) | 1 |
| Offside Rear Brake cable has a seized clevis joint pivot |3.5.1c| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced chassis (7.1.1 (a) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded a/r/b |2.4.A.3| | 1 |
| Nearside Front Seat belt webbing significantly weakened |7.1.2 |b| |ii|| | 1 |
| Front suspension has excessive movement at a suspension ball joint O/S/F LOWER |2.5.A.1c| | 1 |
| Seat belt anchorage prescribed area is excessively corroded N/S/R OUTER SILL |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded O/S/R OUTER SILL |5.2.6| | 1 |
| Offside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings seat belt mounting |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sills two places (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Front Lower Suspension component ball joint excessively worn both sides (5.3.4 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill and floor pan (7.1.1 (a) (i)) | 1 |
| Offside Front Headlamp insecure brackets broke |4.1.1 |c|| | 1 |
| Exhaust has a major leak of exhaust gases connecting flange mid/rear corroded and broke |6.1.2 |a|| | 1 |
| Offside Inner Rear Road wheel bead rim badly distorted |4.2.A.1a| | 1 |
| Offside Inner Front Road wheel bead rim badly distorted |4.2.A.1a| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Outer sill coroded !! |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Outer sill coroded !!! |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis leg !!!adjacent to anti roll bar !!! |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis leg adjacent to anti roll bar !! |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill |7.1.1 |a| |i|| | 1 |
| Power steering pipe|s| or hose|s| leaking To power steering pump |2.3.3b| | 1 |
| Offside Front Anti-roll bar missing |2.4.G.1| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre floor pan |6.1.B.2| | 1 |
| Front Headlamp light intensity severely reduced both |4.1.4 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded upper wishbone mounting |2.4.A.3| | 1 |
| Nearside Front Lower Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced NS + OS (4.1.4 (b)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength NS + OS inner wheel archs on chassis rails by under tray (5.3.6 (a) (i)) | 1 |
| Emissions not tested due to exhaust condition |7.3.A.1| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded outer wheel arch |top of| |2.4.A.3| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill /wheel arch |7.1.1 |a| |i|| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor pan |7.1.1 |a| |i|| | 1 |
| Brake performance unable to be tested Brake pipe leaking (1.2.1 (g)) | 1 |
| Nearside Front Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Emissions not tested engin misfire (8.2.1.2 (d)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded/holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded/holed (7.1.1 (a) (i)) | 1 |
| Front Bumper damaged and likely to cause injury when grazed or contacted Number plate holder (6.1.4 (a) (i)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury Wheel arch (6.2.1 (a) (i)) | 1 |
| Offside Rear Hydraulic fluid leaking excessively caliper |8.4.1 |a| |i|| | 1 |
| Rear Exhaust has a major leak of exhaust gases back/ box |7.1.2| | 1 |
| Headlamp lens seriously defective BOTH FRONT (4.1.1 (b) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting INNER FLOOR TO SILL HOLED (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded within 30cm of belt mount prescribed area (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail corroded holed (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail middle of vehicle corroded/small hole (6.1.1 (c) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases multiple exhaust leaks (6.1.2 (a)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wing area (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced wing & sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings WHEEL ARCH |6.1.B.2| | 1 |
| Front Headlamp aim so that beam "kick up" is not visible on the screen Both front |4.1.2 |a|| | 1 |
| Nearside Rear Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill section has a hole in it . |6.1.1 |c| |i|| | 1 |
| Offside Inner Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg |6.1.1 |c| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Outer sill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system Burst on brake test |1.1.11 |b| |ii|| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Rear Upper Anti-roll bar linkage ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Offside Rear Lower Anti-roll bar linkage ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Inner Floor excessively deteriorated sill marked with yellow chalk |6.2.4 |a| |i|| | 1 |
| Offside Rear Inner Floor excessively deteriorated sill marked with yellow chalk |6.2.4 |a| |i|| | 1 |
| Offside Outer Floor excessively deteriorated floor to sill |6.2.4 |a| |i|| | 1 |
| Headlamp has a product on the lens which changes emitted colour to other than white or yellow |4.1.4 |b|| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering inner arch corroded |6.1.A.1| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced main & dip beam |1.7.5a| | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis holed by rust (6.2.2 (d) (i)) | 1 |
| Central Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded Cill |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded cill |2.4.A.3| | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/suspension mounting (6.1.1 (c) (i)) | 1 |
| Nearside Body insecure and dangerous to other road users sideskirt |6.1.B.1b| | 1 |
| Offside Body insecure and dangerous to other road users sideskirt |6.1.B.1b| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner c hassis leg |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre |6.1.B.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded floor and jacking point |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |inner wheel arch| |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |inner wheel arch| |6.1.A.1| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases back box |7.1.2| | 1 |
| Offside Subframe mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering As marked (6.1.1 (c) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing chassis rail within 30cm of anti-roll bar bush mounting |2.4.A.3| | 1 |
| Brake pipe leaking on a hydraulic braking system pipe from master cylinder (1.1.11 (b) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both outer sills |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor pan / inner sill |5.2.6| | 1 |
| Nearside Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Offside Front Anti-roll bar worn and seriously weakened |2.4.G.1| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Within 30cm of anti roll bar mount and sub frame mounting mounting point |2.4.A.3| | 1 |
| Parking brake inoperative on one side no lock on both sides (1.4.1 (a)) | 1 |
| Emissions not tested co exceeding limits on 2nd fast idle emissions test stopped due to cooling system fan not working (8.2.1.2 (d)) | 1 |
| Offside Front Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Offside Front Seat belt webbing significantly weakened (7.1.2 (b) (ii)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn linkage broken (5.3.4 (a) (i)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
| Front Headlamp aim beam image obviously incorrect BOTH - deteriorated - misty |1.8.A.1b| | 1 |
| Nearside Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Offside Front Tie bar/rod damaged and seriously weakened |2.4.G.1| | 1 |
| Parking brake recording little or no effort |3.7.D.3a| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Rear outer sill |5.2.6| | 1 |
| Headlamp light source and lamp not compatible both sides have h.i.ds fitted |4.1.4 |c|| | 1 |
| Nearside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Emissions not tested due to no catalytic converter fitted |8.2.1.2 |d|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded chassis |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch holed and corrosion |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheel arch holed and corrosion |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded floor corroded |2.4.A.3| | 1 |
| Nearside Headlamp cleaning device inoperative |1.7.2| | 1 |
| Offside Headlamp cleaning device inoperative |1.7.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill wheel arch |6.1.B.2| | 1 |
| Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced lense opaque and requires polishing |1.7.5a| | 1 |
| Offside Front Headlamp excessively deteriorated so that the light output is severely reduced lense opaque and requires polishing |1.7.5a| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer silll / rear wheel arch corroded and holed |6.1.B.2| | 1 |
| Nearside Hydraulic fluid leaking continuously posing a serious risk to road safety PAS fluid (8.4.1 (a) (ii)) | 1 |
| Offside Front Drivers airbag missing steering wheel not factory (7.1.5 (a)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both sides anti roll bar and subframe mounting corroded chassis (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed leak (8.2.1.2 (d)) | 1 |
| Power steering disconnected where it is standard fitment |2.3.3a| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill yellow chalked |7.1.1 |a| |i|| | 1 |
| Nearside Front position lamp|s| not working Rectified PRS |1.1.A.3b| | 1 |
| Exhaust engine idle speed too high Emissions failed BET test, first fast idle test and second fast idle test on high lambda valu. Idle speed above specified limit so emissions at idle not completed and unable to obtain printout |7.3.D.1| | 1 |
| Emissions not tested Unable to complete emissions test as idle speed is outside specified limits |7.3.A.1| | 1 |
| Rear Anti-roll bar missing anti-roll bar and links missing (5.3.3 (a) (ii)) | 1 |
| Offside Rear Outer Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings sill corroded |6.1.B.2| | 1 |
| Offside Rear Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Centre floor to inner sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wing and chassis rail at anti roll bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill at rear (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Centre inner sill to floor excessively corroded (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Inner and outer sill |5.2.6| | 1 |
| Nearside Front Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing/chassis near strut mount |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Offside Front Hydraulic brake calliper damaged and braking performance affected caliper seized |1.1.16 |a| |ii|| | 1 |
| Nearside Statutory seat belt missing stalk |5.1.1| | 1 |
| Offside Statutory seat belt missing stalk |5.1.1| | 1 |
| Offside Front Steering rack damaged and unserviceable |2.2.C.1d| | 1 |
| Offside Windscreen wiper missing (3.4 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill. (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Sill. (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Track rod end ball joint worn to the extent there is a serious risk of detachment nut not tightened (2.1.3 (b) (ii)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced central chassis holed |6.1.1 |c| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired inner sill and floor pan |7.1.1 |a| |i|| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases exhaust flange |6.1.2 |a|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Outer cil |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer cil |5.2.6| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded inner sill/floor pan |5.2.6| | 1 |
| Offside Body insecure sile holed. |6.2.2 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage worn and seriously weakened drop link broken |2.4.G.1| | 1 |
| Front Inner Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
| Rear Inner Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill/wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill/wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Obligatory mirror missing Glass |8.1.1| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Floor pan marked in chalk |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Excessive corrosion / holes to sill / inner wheel arch areas (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Excessive corrosion / holes to sill / inner wheel arch areas (7.1.1 (a) (i)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system Floor area (brake pipes front to rear) (1.1.11 (b) (ii)) | 1 |
| Offside Front Front suspension has a loose unit in the upper support bearing assembly |2.5.B.3b| | 1 |
| Front Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill & inner sill/floor (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill and under sill (7.1.1 (a) (i)) | 1 |
| Brake pipe at imminent risk of failure or fracture Front to rear (1.1.11 (a)) | 1 |
| Brake pipe at imminent risk of failure or fracture Across rear axle (1.1.11 (a)) | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner arch/ chassis leg |2.4.A.3| | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system front to rear section |1.1.11 |b| |ii|| | 1 |
| Parking brake lever insecure |3.1.3b| | 1 |
| Nearside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength Under body sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength Under body sill |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Floor pan |5.2.6| | 1 |
| Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Nearside Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Upper Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced Nearside & offside faded / discoloured (4.1.4 (b)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WING ON FRONT OF CHASSIS FOR ROLL BAR MOUNTING (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS AROUND JACKING POINT (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS AROUND JACKING POINT (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis inner wing area holed and corroded |5.3.6 |a| |ii|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill section holed and corroded |7.1.1 |a| |i|| | 1 |
| Rear Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/floor (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill/floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Centre floor to sill holed / excessively corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill excessively corroded / holed (7.1.1 (a) (i)) | 1 |
| Offside Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Offside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has damage which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front Upper Ball joint damaged and unserviceable |2.2.C.1d| | 1 |
| Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills |5.3.6 |a| |i|| | 1 |
| Front Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Front Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached detached at ball joint (5.3.4 (a) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded and offside |2.4.A.3| | 1 |
| Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Front Inner Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened holed (5.3.3 (b) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced centre & rear under sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre & rear under sill (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger / under sill (5.3.6 (a) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg at centre (6.1.1 (c) (i)) | 1 |
| rear brake recording little or no effort both sides |3.7.B.5a| | 1 |
| Exhaust has a major leak of exhaust gases pipe in to rear silencer |7.1.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg by anti roll bar mount |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg by anti roll bar mount |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength outer sill weld not taken |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded OUTER SILL |5.2.6| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint broke |2.4.G.2| | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak joint |8.2.1.1 |b|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor corroded |7.1.1 |a| |i|| | 1 |
| Offside Rear Hydraulic brake cylinder leaking hydraulic fluid rear caliper leaking (1.1.16 (b) (i)) | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Hydraulic brake cylinder leaking and braking performance affected |1.1.16 |b| |ii|| | 1 |
| Rear Anti-roll bar insecure |2.4.G.1| | 1 |
| Nearside Rear Wheel bolt|s| missing |4.2.A.1e| | 1 |
| Nearside Rear brake caliper securing device loose |3.5.1j| | 1 |
| Offside Front Lower Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Nearside Outer Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Outer Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Outer Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Oil leaking continuously from transmission posing a serious risk to road safety clutch slave cylinder leaking (8.4.1 (a) (ii)) | 1 |
| Nearside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Rear fog lamp light intensity significantly reduced |4.5.4 |a|| | 1 |
| Offside Rear Anti-roll bar damaged and seriously weakened |2.4.G.1| | 1 |
| Offside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Chassis and attachment bracket corroded and missing |5.3.6 |a| |ii|| | 1 |
| Nearside Front Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Front Service brake imbalanced across an axle |1.2.1 |b| |i|| | 1 |
| Nearside Rear Road wheel more than one fixing missing |5.2.1 |a| |ii|| | 1 |
| Offside Rear Road wheel more than one fixing missing |5.2.1 |a| |ii|| | 1 |
| Nearside Front brake caliper leaking missing |3.6.A.1| | 1 |
| Wheel nut|s| missing o/s/r and n/s/r and n/s/f 2 nuts missing each wheel |4.2.A.1e| | 1 |
| Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s and o/s inner arch area |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Sill area at rear |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Sill at rear |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases centre section |7.1.2| | 1 |
| Offside Front Side repeater has less than 50% of the light sources illuminating |1.4.A.2c| | 1 |
| Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis area as marked |6.1.B.2| | 1 |
| Offside Front Track rod end ball joint dust cover missing (2.1.3 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases rear tail pipe |7.1.2| | 1 |
| Nearside Rear Shock absorbers insecurely attached |5.3.2 |a| |i|| | 1 |
| Front Body panel insecure |6.2.1 |a| |i|| | 1 |
| Emissions unable to be completed excessive exhaust leak (8.2.1.2 (d)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is inadequately repaired sill bonded on not welded (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is inadequately repaired sill bonded on not welded (5.3.6 (a) (i)) | 1 |
| Nearside Front Steering locking device missing track rod end. (2.1.3 (d)) | 1 |
| Offside Front Steering locking device missing track rod end. (2.1.3 (d)) | 1 |
| Offside Rear Braking system leaking Caliper leaking fluid. |3.6.A.1| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill to floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength end of sill (5.3.6 (a) (i)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.09 (8.2.1.2 (c)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded inner wheelarch |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner wheelarch |2.4.A.3| | 1 |
| Nearside Body panel corroded and likely to cause injury inner sill |6.2.1 |a| |i|| | 1 |
| Suspension component mounting prescribed area is excessively corroded O/S AND N/S OUTER SILLS CORRODED |2.4.A.3| | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced also no beam pattern (4.1.4 (b)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill, |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor centre corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded roll bar mount |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded roll bar mount |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded near top suspension mounting |2.4.A.3| | 1 |
| Nearside Inner Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Upper Sub-frame pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Power steering pipe/hose excessively corroded onto rack (2.1.5 (g) (i)) | 1 |
| Rear Inner Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Brake hose leaking on calliper |3.6.A.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill and inner wheel arch |5.2.6| | 1 |
| Emissions not tested due to water leak |7.4.B.1| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill area |2.4.A.3| | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill has excessive corrosion |6.1.B.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill has excessive corrosion |6.1.B.2| | 1 |
| Anti-roll bar linkage has excessive play in a ball joint both rear |2.4.G.2| | 1 |
| Suspension component mounting prescribed area is excessively corroded both rear outer sills, nearside inner sill |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area is excessively corroded offside chassis leg |5.2.6| | 1 |
| Offside Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 1 |
| Offside Front Track rod end excessively corroded and unserviceable |2.2.C.1d| | 1 |
| Offside Front Suspension arm locating pin locking device missing |2.4.G.3b| | 1 |
| Nearside Rear Shock absorber casing corroded externally so the unit does not function |2.7.2a| | 1 |
| Tie bar/rod has excessive play in a ball joint o/s/f |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper suspension arm chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper suspension arm chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting chassis leg (5.3.6 (a) (i)) | 1 |
| Brake performance not tested due to broken coil spring |1.2.1 |g|| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arm (5.3.6 (a) (i)) | 1 |
| Driver`s seat insecure bolt loose |6.2.5 |a| |ii|| | 1 |
| Nearside Rear Brake pipe connection leaking on a hydraulic braking system brake pipe |1.1.11 |b| |ii|| | 1 |
| Hydraulic fluid leaking excessively p steering |8.4.1 |a| |i|| | 1 |
| Nearside Front Shock absorbers likely to become detached lower bush |5.3.2 |a| |ii|| | 1 |
| Offside Front Shock absorbers likely to become detached lower bush |5.3.2 |a| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner arch |5.2.6| | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt droplink |5.3.4 |b| |ii|| | 1 |
| Offside Front Floor excessively deteriorated holed and corroded (6.2.4 (a) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting drivers seat floor area (6.2.2 (d) (i)) | 1 |
| Brake valve leaking at brake master cylinder (1.1.7 (d) (i)) | 1 |
| Nearside Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Front Side repeater has less than 50% of the light sources illuminating |1.4.A.2c| | 1 |
| Nearside Rear Coil spring fractured or broken at top end (5.3.1 (b) (i)) | 1 |
| Brake performance not tested Due to O/S/R brake issue (1.2.1 (g)) | 1 |
| Emissions not tested Due to low engine oil level (8.2.1.2 (d)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded Sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired Chassis not seam welded (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail (5.3.6 (a) (i)) | 1 |
| Power steering pipe/hose leaking suspect return line |2.1.5 |a|| | 1 |
| Central Front Lower Windscreen damaged and affecting the driver`s view of the road |3.2 |a| |ii|| | 1 |
| Offside Rear Exhaust emissions likely to be affected by an exhaust leak Centre and rear boxes |8.2.1.1 |b|| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail |5.3.6 |a| |i|| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Sill |7.1.1 |a| |i|| | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected white light |4.5.1 |b| |ii|| | 1 |
| Nearside Front Electrical wiring insecure ABS sensor |1.9.2a| | 1 |
| Offside Front Electrical wiring insecure ABS sensor |1.9.2a| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering engine bay inner wing |6.1.A.1| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing/chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Service brake excessively binding Recording 40-50KgF when released |1.2.1 |f|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor/inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill corroded |5.2.6| | 1 |
| Nearside Rear Suspension arm fractured |5.3.3 |b| |ii|| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced lower sill center (6.1.1 (c) (i)) | 1 |
| Front Front position lamp|s| not working Both |1.1.A.3b| | 1 |
| Exhaust has a major leak of exhaust gases exhaust poor condition resealed joint to get emissions pass (6.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis / inner wing |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis / inner wing |2.4.A.3| | 1 |
| Central Exhaust has a major leak of exhaust gases At joint (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wheel arch |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wheel arch |5.3.6 |a| |ii|| | 1 |
| Offside Inner Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis under wheel arch |2.4.A.3| | 1 |
| Nearside Front Seat belt retracting mechanism defective not retracting (7.1.2 (e)) | 1 |
| Service brake is causing the vehicle to swerve to the offside |3.7.C.2| | 1 |
| Rear Anti-roll bar damaged and seriously weakened |2.4.G.1| | 1 |
| Emissions unable to be completed CO2 IS TOO HIGH (8.2.1.2 (d)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer sill corroded and holed. (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill. |6.1.1 |c| |i|| | 1 |
| Offside Front Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired Sill damage taped - no structure underneath tape when tested via thumb pressure (7.1.1 (a) (i)) | 1 |
| Position lamp missing both front (4.2.1 (a) (ii)) | 1 |
| Nearside Front Upper Suspension arm ball joint likely to become detached split pin missing (5.3.4 (a) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near side outer sill at rear (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength off side outer sill at rear (5.3.6 (a) (i)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect lense cloudy |4.1.2 |c|| | 1 |
| Offside Rear Inner brake disc in such a condition that it is seriously weakened Side |3.5.1i| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail. (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail. (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded trough (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Nearside Rear Lower Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Nearside Rear Upper Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Nearside Rear Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mounting (5.3.6 (a) (i)) | 1 |
| Rear Service brake excessively fluctuating both (1.2.1 (e)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Chassis near a/roll bar |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis near a/roll bar |6.1.A.1| | 1 |
| Nearside Statutory seat belt missing |5.1.1| | 1 |
| Emissions not tested (8.2.2.2 (e)) | 1 |
| Suspension component mounting prescribed area is excessively corroded nearside and offside front inner wings |2.4.A.3| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Offside Outer Rear Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassisx2 (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassy leg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassy leg |2.4.A.3| | 1 |
| Rear Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Hazard warning switch inoperative All lamps not working (4.4.2 (a) (ii)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill/floor pan (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting likely to become detached |5.3.3 |a| |ii|| | 1 |
| Nearside Upper Front suspension locking device missing |2.5.A.4| | 1 |
| Nearside Rear Brake pipe kinked |3.6.B.2b| | 1 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded SILL |2.4.A.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases exhaust section heavily corroded at rear joint,and tail pipe is holed and leaking. |7.1.2| | 1 |
| Nearside Front Upper Coil spring fractured or broken |5.3.1 |b| |i|| | 1 |
| Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Coil spring fractured or broken broken (5.3.1 (b) (i)) | 1 |
| Nearside Rear Brake lever has restricted free movement caliper lever stuck on (1.1.15 (e)) | 1 |
| Central Exhaust has a major leak of exhaust gases and rear |6.1.2 |a|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded chassis leg |2.1.2 |e| |i|| | 1 |
| Offside Rear Seat belt anchorage likely to become detached in the event of a collision sill |7.1.1 |a| |ii|| | 1 |
| Offside Front Inner Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded front of inner wheelarch area |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner lower sill area |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner lower sill area |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer lower sill area |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer lower sill area |5.2.6| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion outer wheel arch area |6.1.C.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases @ silencer join |7.1.2| | 1 |
| Nearside Rear Braking system leaking @ caliper |3.6.A.1| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded under side of front chassis rail |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded front of inner wheel arch area |5.2.6| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded inner sill area |5.2.6| | 1 |
| Nearside Rear Lower Suspension arm damaged and seriously weakened has been cut near shock mounting area |2.4.G.1| | 1 |
| Offside Rear Lower Suspension arm damaged and seriously weakened has been cut near shock mounting area |2.4.G.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced INNER AND OUTER SILL CORRODED (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced INNER AND OUTER SILL CORRODED (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Upper suspension arm front bush mounting |2.4.A.3| | 1 |
| Nearside coil spring incomplete |2.4.C.1a| | 1 |
| Nearside Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Front position lamp|s| not working side light and main beam |1.1.A.3b| | 1 |
| Offside Front Front position lamp|s| not working sidelight |1.1.A.3b| | 1 |
| Offside Rear Stop lamp not working brake light |1.2.1b| | 1 |
| Offside Rear Brake hose leaking on a hydraulic braking system Hose area (1.1.12 (c) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage likely to become detached (5.3.3 (a) (ii)) | 1 |
| Power steering component|s| leaking Rack area |2.3.3b| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits 1.11 |7.3.D.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases Centre to rear silencer joint - Flange corroded and blowing |7.1.2| | 1 |
| Offside Lower Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Subframe mounting prescribed area excessively damaged significantly reducing structural strength Front subframe rear mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Nearside Front Inner Anti-roll bar attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Rear Torsion bar attachment bracket loose |2.4.E.4a| | 1 |
| Nearside Front Electrical wiring insecure ABS wiring |1.9.2a| | 1 |
| Inner Front brake disc excessively scored |3.5.1h| | 1 |
| Rear Exhaust system not adequately supported clip at joint loose |7.1.1| | 1 |
| Rear Brake pedal does not operate a brake fitted to each wheel |3.3.A.3| | 1 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill. (6.1.1 (c) (i)) | 1 |
| Battery insecure and likely to cause a short circuit in the boot (4.13 (a) (ii)) | 1 |
| Offside Rear Brake hose excessively damaged to caliper (1.1.12 (b) (ii)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill end |7.1.1 |a| |i|| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Vehicle structure is deformed and structural rigidity is significantly reduced outer sill not repaired correctly (6.1.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure is deformed and structural rigidity is significantly reduced outer sill not repaired correctly (6.1.1 (a) (i)) | 1 |
| Offside Front Brake pipe likely to become detached or damaged (1.1.11 (d) (ii)) | 1 |
| Offside Front brake disc insecure |3.5.1i| | 1 |
| Offside Front Upper Suspension arm ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Rear Exhaust has a major leak of exhaust gases joint (6.1.2 (a)) | 1 |
| Brake hydraulic reservoir cap missing |3.6.G.1a| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (marked) (7.1.1 (a) (i)) | 1 |
| Offside Front Exhaust emissions likely to be affected by an induction leak |8.2.1.1 |b|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting nr subframe mount |6.2.2 |d| |i|| | 1 |
| Nearside Front Inner Body component insecure arch (6.2.1 (a) (i)) | 1 |
| Rear Body component insecure bumper (6.2.1 (a) (i)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner Sill panel |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner chassis (5.3.6 (a) (i)) | 1 |
| Nearside Front Steering locking device missing split pin missing |2.2.C.1g| | 1 |
| Front Suspension arm locating pin locking device missing both sides bottom ball joint split pins missing |2.4.G.3b| | 1 |
| Offside Front Upper Suspension arm locating pin retaining device missing ball joint split pin missing |2.4.G.3b| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded both sides at chassis legs /wishbone/antiroll bar |2.4.A.3| | 1 |
| Nearside Rear Lower Shock absorber insecure |2.7.2b| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt upper and lower (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt upper and lower (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Brake pressure storage reservoir leaking caliper bleed nipple wet (1.1.9 (a) (ii)) | 1 |
| Offside Rear Brake pressure storage reservoir leaking caliper bleed nipple wet (1.1.9 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner wheelarch (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength main chassis (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed car getting hot (8.2.1.2 (d)) | 1 |
| Nearside Front Steering system fouling brake hose (2.1.4 (a)) | 1 |
| Rear Upper Suspension arm corroded and seriously weakened both sides (5.3.3 (b) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill (6.1.1 (c) (i)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front panel to chassis end both sides by tow eyes (6.1.1 (c) (i)) | 1 |
| Central Upper Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Inner Suspension spring mounting prescribed area is excessively corroded arch/chassis leg |2.4.A.3| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced length of car (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 1 |
| Offside Rear Inner Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear rear brake recording little or no effort HAND BRAKE |3.7.B.5a| | 1 |
| Offside Front Brake valve insecure Caliper (1.1.7 (c)) | 1 |
| Offside Rear Wheel bearing play so excessive it is likely to break up (5.1.3 (a) (ii)) | 1 |
| Nearside Rear Hydraulic brake calliper leaking banjo joint leaking (1.1.16 (b) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength offside rear outer sill (5.3.6 (a) (i)) | 1 |
| Sub-frame attachment bracket/mounting fractured both rear axle support brackets corroded |5.3.3 |b| |ii|| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering wheel arch |6.1.1 |c| |ii|| | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering sill to floor |6.1.A.1| | 1 |
| Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering outer sill |6.1.A.1| | 1 |
| Suspension component mounting prescribed area is excessively corroded both outer sills |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor to sill areas |5.2.6| | 1 |
| Emissions not tested exhaust pipes corroded/ detached. |8.2.1.2 |d|| | 1 |
| Offside Rear Upper Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Vehicle structure has a fracture which is likely to adversely affect braking or steering (6.1.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer door sill |5.2.6| | 1 |
| Offside Floor excessively deteriorated offs
sill to floor corroded |6.2.4 |a| |i|| | 1 |
| Nearside Front Upper Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Front Upper Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis underside |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings innersill |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer chassis |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings innersill |6.1.B.2| | 1 |
| Nearside Rear Braking system leaking brake caliper leaking |3.6.A.1| | 1 |
| Rear Sub-frame attachment bracket/mounting likely to become detached Both Rear Subframe mountings (5.3.3 (a) (ii)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting & Outer Sill/ Wheel Arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Offside Front Upper Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Front Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 1 |
| Offside Rear Anti-roll bar linkage damaged and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded middle outer sill |5.2.6| | 1 |
| Emissions not tested Abandoned (8.2.1.2 (d)) | 1 |
| Emissions unable to be completed Lambda off readable scale (8.2.1.2 (d)) | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint drop link |2.4.G.2| | 1 |
| Offside Front Brake disc significantly and obviously worn excessive heat (1.1.14 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe/anti rollbar mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe/anti rollbar mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear position lamp|s| obscured more than 50% |1.1.A.3c| | 1 |
| Offside Stop lamp obscured more than 50% |1.2.1c| | 1 |
| Emissions not tested Engine overheating. CO @ 2nd fast idle too high. (8.2.1.2 (d)) | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded BOTH sills |2.4.A.3| | 1 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded sill and inner sill |5.2.6| | 1 |
| Nearside Front Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Offside Front Headlamp adversely affected by the operation of another lamp Dipped beam |1.7.5c| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis rail, in wheel arch |2.4.A.3| | 1 |
| Offside Rear Suspension arm pin or bush excessively worn front bush |5.3.4 |a| |i|| | 1 |
| Seat belt anchorage prescribed area is excessively corroded both outer sills |5.2.6| | 1 |
| Battery insecure Battery tray weakened by corrosion |1.9.1| | 1 |
| Exhaust has a major leak of exhaust gases centre exhaust clamp leaking |6.1.2 |a|| | 1 |
| Rear Service brake excessively fluctuating nearside and offside (1.2.1 (e)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor under drivers seat 2 places (7.1.1 (a) (i)) | 1 |
| Front Shock absorbers has an excessively worn bush Both sides (5.3.2 (c)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced NSR & OSR inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Integral body structure modified such that structural rigidity is significantly reduced sill (6.1.1 (d) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Brake hose leaking on a hydraulic braking system flexible hose to caliper (1.1.12 (c) (ii)) | 1 |
| Nearside Front Brake hose excessively twisted twisted and touching suspension when on lock (1.1.12 (b) (ii)) | 1 |
| Offside Rear Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg corroded |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg corroded |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor under vehicle |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor under vehicle |5.2.6| | 1 |
| Nearside Power steering pipe/hose leaking rack leaking |2.1.5 |a|| | 1 |
| Brake disc significantly and obviously worn all |1.1.14 |a| |i|| | 1 |
| Nearside Front Front position lamp|s| not working sidelight |1.1.A.3b| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Offside Front Seat belt flexible stalk deteriorated likely to lead to failure under load |5.2.4a| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced throughout also very heavy undersealed (6.1.1 (c) (i)) | 1 |
| Rear Suspension arm corroded and seriously weakened n/s and o/s upper arms (5.3.3 (b) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Body component corroded and likely to cause injury wheel arch |6.2.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chasis leg cracked and corroded |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired Inner sill panel repair stitch welded - must be seam welded - marked. |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Floor panel |rear| - marked. |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Floor panel |middle| - marked. |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Floor panel |middle| - marked. |5.2.6| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded Floor panel |front| - marked. |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded Chassis - 3 sides of box section - marked. |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded Chassis inside wheelarch - marked. |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded End of sill panel inside wheelarch - marked. |5.2.6| | 1 |
| Offside Front Lower Ball joint ball pin shank loose castlated nut / split pin missing |2.2.B.1c| | 1 |
| Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Headlamp levelling device cannot be operated from the drivers seat (4.1.5 (b)) | 1 |
| Offside Front Headlamp levelling device cannot be operated from the drivers seat (4.1.5 (b)) | 1 |
| Nearside Rear Service brake excessively binding caliper sticking (1.2.1 (f)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Offside Rear Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper leaking |3.6.A.1| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor to sill under car |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel arch |7.1.1 |a| |i|| | 1 |
| Rear Brake disc significantly and obviously worn o/s & n/s |1.1.14 |a| |i|| | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Brake pipe modified and seriously weakened as marked |3.6.A.3| | 1 |
| Rear Subframe mounting prescribed area is excessively corroded both rear outer sill |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced n/s inner sill |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced n/s/r inner sill |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced o/s inner sill |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced o/s/r inner sill |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced n/s/r outer sill |7.1.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch holed |5.3.6 |a| |i|| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor |5.3.6 |a| |i|| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed |5.3.6 |a| |i|| | 1 |
| Front Headlamp aim not tested (4.1.2 (b)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected front chassis leg (5.3.6 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage modified and seriously weakened |2.4.A.2| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill to floor |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded chassis rail |5.2.6| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 1 |
| Offside Front Body has a sharp edge caused by corrosion wing |6.1.C.1| | 1 |
| Nearside Front Hydraulic brake calliper leaking and braking performance affected (1.1.16 (b) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front chassis rails ( under side ) (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail / inner flitch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired under sill panel (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Inner chassis |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded |7.1.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch corroded |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill/wheelarch |5.2.6| | 1 |
| Exhaust emissions exceed level of metered smoke for a non-turbo charged engine (8.2.2.2 (b)) | 1 |
| Rear Exhaust system not adequately supported two rubber supports snaped and third one splitting badly |7.1.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering underside of chassis near top suspension arm |6.1.1 |c| |ii|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering underside of chassis near top suspension arm |6.1.1 |c| |ii|| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering outer sill |6.1.1 |c| |ii|| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering outer sill |6.1.1 |c| |ii|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded at rear inner sill panel |5.2.6| | 1 |
| Brake performance not tested due to no hand brake performance at all |3.7.A.1| | 1 |
| Nearside Rear Brake rod has restricted free movement (1.1.15 (e)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (inner and outer) (6.1.1 (c) (i)) | 1 |
| Offside Front Brake rod has restricted free movement (1.1.15 (e)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (inner and outer) (6.1.1 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting fractured |5.3.3 |b| |ii|| | 1 |
| Offside Front Upper Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Lower Suspension arm insecurely attached |5.3.3 |a| |i|| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits miss fire (8.2.1.2 (b)) | 1 |
| Rear Coil spring fractured or broken n/s o/s (5.3.1 (b) (i)) | 1 |
| Offside Rear Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor pan [seat mount] |6.1.1 |c| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill area |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis inner arch |2.4.A.3| | 1 |
| Offside Headlamp not working on dipped beam Bulb not plugged in. |1.7.5a| | 1 |
| Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt n/s and o/s (2.1.3 (g) (ii)) | 1 |
| Offside Rear Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Offside Rear brake caliper modified and seriously weakened |3.5.1n| | 1 |
| Nearside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Nearside Rear Outer Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak center to rear clamp leaking |8.2.2.1 |b|| | 1 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength neat anti roll bar brackets |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength near anti roll bar brackets |5.3.6 |a| |i|| | 1 |
| Front coil spring broken |2.4.C.1a| | 1 |
| Battery insecure and likely to cause a short circuit clamp loose (4.13 (a) (ii)) | 1 |
| Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Bonnet cannot be secured in the closed position |3.1 |b| |i|| | 1 |
| Offside Front Side repeater missing |1.4.A.2b| | 1 |
| Nearside Inner Rear Brake pipe excessively damaged |3.6.B.2c| | 1 |
| Offside Front Position lamp with a multiple light source more than 1/2 not functioning (4.2.1 (a) (ii)) | 1 |
| Nearside Front Side repeater adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Emissions not tested Exhaust leak (8.2.1.2 (d)) | 1 |
| Offside Front Front position lamp|s| not working MAIN BEAM |1.1.A.3b| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis...... anti-roll bar body mounting |2.4.A.3| | 1 |
| Offside Front Upper Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill at rear (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/chassis leg at sub-frame mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (bottom of chassis leg) (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (bottom of chassis leg) (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to floor pan |7.1.1 |a| |i|| | 1 |
| Nearside Headlamp lens seriously defective Faded - No Beam Image and reduced light intensity (4.1.1 (b) (ii)) | 1 |
| Offside Headlamp lens seriously defective Faded - No Beam Image and reduced light intensity (4.1.1 (b) (ii)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced nearside front sill |6.1.1 |c| |i|| | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced offside front sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Lower Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Front suspension has a suspension lower ball joint securing nut not locked |2.5.B.1a| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis rail (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis rail (6.2.2 (d) (i)) | 1 |
| Rear Axle has inadequate clearance with the chassis |2.4.A.1a| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded boot floor |2.4.A.3| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect bulb inserted incorrectly |1.8.A.1b| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded INNER SILL/FLOOR X 2 |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded INNER SILL/FLOOR |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded INNER SILL/FLOOR |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg near anti roll bar mount |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg near anti roll bar mount |5.3.6 |a| |i|| | 1 |
| Front Macpherson strut has an unsafe modification mismatching struts fitted to front with altering spring loadings and shock rebound (5.3.3 (c) (i)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced No pattern visible due to dull lens (4.1.4 (b)) | 1 |
| Emissions oxygen sensor missing where one was fitted as standard (8.2.1.1 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill excessively corroded within prescribed area |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired chassis inside &out (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired chassis inside & out (5.3.6 (a) (i)) | 1 |
| Nearside Outer Front brake disc excessively scored |3.5.1h| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Front Headlamp has more than 1/2 LEDs not functioning (4.1.1 (a) (ii)) | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering offside front inner wing |6.1.1 |c| |ii|| | 1 |
| Offside Rear Brake modification unsafe Brake hose rubbing on wheel. (1.1.21 (d) (i)) | 1 |
| Offside Rear Coil spring mounting fractured |2.4.C.3b| | 1 |
| Nearside Rear Coil spring mounting fractured |2.4.C.3b| | 1 |
| Nearside Front Body component damaged and likely to cause injury Mirror sharp edges (6.2.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sil (7.1.1 (a) (i)) | 1 |
| Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Rear Hydraulic fluid leaking excessively |8.4.1 |a| |i|| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits See report (8.2.1.2 (b)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill areas (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner and outer sill areas (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded centre floor to sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded lower chassis |2.4.A.3| | 1 |
| Front Brake pipe at imminent risk of failure or fracture to rear brake pipe leaking (1.1.11 (a)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt both sides |5.3.4 |b| |ii|| | 1 |
| Nearside Front Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength wheelarch |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded |7.1.1 |a| |i|| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak REAR JOINT (8.2.1.1 (b)) | 1 |
| Offside Front Anti-roll bar linkage insecurely attached BROKEN (5.3.3 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced WHEEL ARCH CORRODED (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak CENTRE SECTION (8.2.1.1 (b)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded seal |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded seal |5.2.6| | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Wheel arch |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner wing |5.3.6 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected inner wing |5.3.6 |a| |ii|| | 1 |
| Offside Headlamp aim does not move downwards when dipped |British American headlamp| |1.8.C.4| | 1 |
| Nearside Front Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner door sill (6.1.1 (c) (i)) | 1 |
| Offside Front Brake pipe at imminent risk of failure or fracture to rear (1.1.11 (a)) | 1 |
| Offside Rear Brake performance unable to be tested brake pipe (1.2.1 (g)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg lower section heavily corroded and holed |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg heavily corroded and holed |6.1.1 |c| |i|| | 1 |
| Nearside Floor excessively deteriorated sill to floor corroded and holed |6.2.4 |a| |i|| | 1 |
| Front front brake binding both side front |3.7.B.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill |5.3.6 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner sill and inner wheel arch |5.3.6 |a| |ii|| | 1 |
| Offside Front Wheel bearing so rough it is likely to overheat or break up |5.1.3 |b| |ii|| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill areas (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill areas (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength complete chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength compete chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion which adversely affects braking or steering sill |6.1.1 |c| |ii|| | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sub frame mount/in wheel arch (6.2.2 (d) (i)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt split |2.1.3 |g| |ii|| | 1 |
| Rear Brake pipe leaking on a hydraulic braking system main (1.1.11 (b) (ii)) | 1 |
| Rear front brake recording little or no effort both |3.7.B.5a| | 1 |
| Nearside Rear Rear position lamp|s| not in a clean condition and function impaired |1.1.4a| | 1 |
| Offside Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting centre section of inner floor near sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded of sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded of sill |2.4.A.3| | 1 |
| Exhaust emissions exceed manufacturers specified limit as test result (8.2.2.2 (a)) | 1 |
| Nearside Front brake caliper has restricted free movement and nearside rear |3.5.1k| | 1 |
| Rear fog lamp switch missing Not found (4.5.3 (a)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to floor edge (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill to floor |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill to floor |6.1.B.2| | 1 |
| Exhaust has a major leak of exhaust gases centre |7.1.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength Chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Undertray likely to become detached (6.2.1 (a) (ii)) | 1 |
| Nearside Rear Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Nearside Front Seat belt insecurely fixed to the seat |5.2.1a| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to sill corroded holed (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded chassis in 2 places |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded centre under sill |5.2.6| | 1 |
| Rear Exhaust has a major leak of exhaust gases flange |7.1.2| | 1 |
| Offside Front Body has a sharp edge caused by corrosion outer wing |6.1.C.1| | 1 |
| Stop lamp|s| not working middle |4.3.1 |a| |ii|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced hole in sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis, boot floor within 30cm to role bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced hole in sill under seatbelt (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded inner arch / chassis leg |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner arch / chassis leg |2.4.A.3| | 1 |
| Fuel system component leaking filter or pipe |7.2.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor section (7.1.1 (a) (i)) | 1 |
| Nearside Front Steering locking device missing track rod end split pin |2.1.3 |d|| | 1 |
| Nearside Front Steering locking device ineffective track rod end locking nut loose |2.1.3 |d|| | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached locking devise missing split pin
ball joint |5.3.4 |a| |ii|| | 1 |
| Nearside Parking brake not fitted on at least two wheels |3.1.1| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg beside anti roll bar mount |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg beside anti roll bar mount |6.1.1 |c| |i|| | 1 |
| Rear Parking brake efficiency below requirements Both Rears (1.4.2 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Offside Front Body has a sharp edge caused by corrosion Wing. |6.1.C.1| | 1 |
| Nearside Rear Upper Seat belt anchorage prescribed area is excessively corroded inner wheel arch |5.2.6| | 1 |
| Offside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Hydraulic fluid leaking excessively pas (8.4.1 (a) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired holes in both sills front to rear weakening floor and body structure (6.2.2 (d) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Offside Front Brake lever has abnormal movement of levers indicating excessive wear or maladjustment park brake lever at the caliper (1.1.15 (f)) | 1 |
| Nearside Front Upper Suspension component ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Upper Suspension component ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits see reverse (8.2.1.2 (b)) | 1 |
| Nearside Steering rack insecure |2.2.B.1a| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced Nearside Front & Offside Front |1.7.5a| | 1 |
| Central Exhaust has a major leak of exhaust gases joint |7.1.2| | 1 |
| Emissions not tested engine started running rough and cut out (8.2.1.2 (d)) | 1 |
| Offside Rear Lower Rear fog lamp not working |1.3.2b| | 1 |
| Offside Rear Lower Rear fog lamp insecure |1.3.2a| | 1 |
| All position lamps not working BOTH FRONT AND REAR N/S + O/S . |1.1.A.3b| | 1 |
| Offside Rear Outer Body has a projection caused by corrosion SILL AREA CORRODED AND HAS SLIGHT PROJECTION OF LOWER SILL PANEL. |6.1.C.1| | 1 |
| Offside Front Shock absorber insecure |2.7.2b| | 1 |
| Offside Front Lower Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to sill (6.2.2 (d) (i)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor to sill (6.2.2 (d) (i)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting boot floor (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor /inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Floor excessively deteriorated /inner sill (6.2.4 (a) (i)) | 1 |
| Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering floor (6.1.1 (c) (ii)) | 1 |
| Seat belt stitching badly frayed |5.2.2b| | 1 |
| Exhaust has a major leak of exhaust gases middle and rear |7.1.2| | 1 |
| Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Brake pipe leaking on a hydraulic braking system front to rear pipe burst whilst on brake roller tester. DO NOT DRIVE (1.1.11 (b) (ii)) | 1 |
| Offside Front Position lamp not working 501 capless bulb replaced during test |4.2.1 |a|| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (marked with chalk) (7.1.1 (a) (i)) | 1 |
| Offside Front Wheel bearing play so excessive that directional control is impaired (5.1.3 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired inner sill |5.3.6 |a| |i|| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive extended CAT test performed |7.3.D.3| | 1 |
| Offside Front Steering linkage ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive extended cat test performed |7.3.D.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded holed and corroded |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded holed and corroded |2.4.A.3| | 1 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded outer sill hol |2.4.A.3| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded ns floor to sill holed and corroded |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded floor to sill holed and corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded suspension arm holed and corroded |2.4.A.3| | 1 |
| Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear Braking system leaking Bleed Nipple |3.6.A.1| | 1 |
| Offside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Front position lamp|s| has a product on the light source so it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under car inner sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under car inner sill |5.3.6 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases centre sleeve |7.1.2| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill under car (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Emissions not tested DUE TO MAJOR EXHAUST LEAK. |7.3.A.1| | 1 |
| Exhaust has a major leak of exhaust gases FRONT AND REAR |7.1.2| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/floor section (5.3.6 (a) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced nearside rear sill and floor to sill (6.1.1 (c) (i)) | 1 |
| Nearside Braking system leaking |3.6.A.1| | 1 |
| Offside Brake cable has restricted free movement hand brake |3.5.1k| | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sills (6.1.1 (c) (i)) | 1 |
| Nearside Front Headlamp adversely affected by the operation of another lamp head light |1.7.5c| | 1 |
| Offside brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting near top mount on inner wing corroded hole. (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded hole in behind of jacking point. (6.1.1 (c) (i)) | 1 |
| Offside Front Position lamp not working side lamp (4.2.1 (a) (ii)) | 1 |
| Offside Front Service brake excessively binding unable to spin wheel by hand. (1.2.1 (f)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded lower outer sill holed and corroded |5.2.6| | 1 |
| Nearside Windscreen wiper blade missing |8.2.2| | 1 |
| Offside Windscreen wiper blade missing |8.2.2| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases rear silencer |6.1.2 |a|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength bay panel (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength bay panel (5.3.6 (a) (i)) | 1 |
| Offside Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill and floor |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill and floor |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Rear Torque/reaction arm insecure |2.4.G.1| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SILL (7.1.1 (a) (i)) | 1 |
| Nearside Rear Macpherson strut corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Front suspension retaining device ineffective |2.5.A.4| | 1 |
| Offside Front suspension retaining device missing |2.5.A.4| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Rear position lamp|s| incorrect colour badly demaged |1.1.A.3e| | 1 |
| Nearside Rear Hydraulic brake calliper leaking damp |1.1.16 |b| |i|| | 1 |
| Offside Front Floor excessively deteriorated holed corroded |6.2.4 |a| |i|| | 1 |
| Offside Headlamps matched pair are not the same colour |1.7.6| | 1 |
| Nearside Front Inner Integral body structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Offside Outer Integral body structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill and wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded chassis leg |2.2.C.1h| | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded chassis leg |2.2.C.1h| | 1 |
| Emissions not tested due to exhaust blow at rear (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail corroded by anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail by anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Road wheel badly distorted inner rim |5.2.2 |c| |i|| | 1 |
| Offside Rear Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Front Horn sounds harsh or grating |1.6.2e| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch |6.1.B.2| | 1 |
| Offside Rear Tie bar/rod attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Offside Front Lower Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded sill/floor |5.2.6| | 1 |
| Offside Braking system leaking pipe |3.6.A.1| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded sill area |2.4.A.3| | 1 |
| Axle with an unsafe modification wooden plates under top diff mounts (5.1.1 (c) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area is inadequately repaired outter sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area is inadequately repaired outter sill (5.3.6 (a) (i)) | 1 |
| Offside Subframe mounting prescribed area is inadequately repaired inner sill (5.3.6 (a) (i)) | 1 |
| Power steering component leaking steering rack offside front gaitor (2.1.5 (a)) | 1 |
| Offside Front Power steering malfunctioning steering juddering |2.3.3a| | 1 |
| Rear Exhaust has a major leak of exhaust gases rear box joint |7.1.2| | 1 |
| Power steering component leaking steering rack leaking from gaitor (2.1.5 (a)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak joint (8.2.2.1 (b)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis holed adjacent to anti roll bar attachment (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded CHASSIS |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases BACK BOX TO TAIL PIPE |7.1.2| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis Leg (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Chassis Leg (6.2.2 (d) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill and floor (7.1.1 (a) (i)) | 1 |
| Nearside Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor/sill (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Subframe mounting prescribed area excessively corroded significantly reducing structural strength floor/sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 1 |
| Offside Front Upper Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases mid box (6.1.2 (a)) | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded inner arch (1.1.21 (e) (i)) | 1 |
| Nearside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` sunstrip |8.3.1e| | 1 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` sunstrip |8.3.1b| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Nearside Front Hydraulic fluid leaking excessively power steering pipe |8.4.1 |a| |i|| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush drop link |2.4.G.2| | 1 |
| Offside Front Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Vehicle structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure strengthening plate or fastening insecure (6.1.1 (b) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 1 |
| Power steering pipe/hose excessively corroded (2.1.5 (g) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases joint is badly corroded |7.1.2| | 1 |
| Nearside Rear Braking system leaking brake calliper |3.6.A.1| | 1 |
| Front Headlamp light intensity severely reduced |4.1.4 |a|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner body sill |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner body sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis & floor pan |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor pan/inner body sill |5.3.6 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases front to middle section (6.1.2 (a)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Rear Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt roll bar link |2.4.G.2| | 1 |
| Nearside Headlamp are incorrectly positioned (4.1.4 (a)) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt Dust cover split (5.3.4 (b) (ii)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt Dust cover split (5.3.4 (b) (ii)) | 1 |
| Nearside Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Parking brake inoperative on one side 40 nm (1.4.1 (a)) | 1 |
| Offside Parking brake inoperative on one side 0 nm (1.4.1 (a)) | 1 |
| Nearside Parking brake inoperative on one side 50 nm (1.4.1 (a)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner & outer sills |5.2.6| | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Outer Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL (7.1.1 (a) (i)) | 1 |
| Spare wheel carrier fractured split by corrosion |6.1.5 |a|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch/chassis |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch/chassis |5.3.6 |a| |i|| | 1 |
| Offside Front Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis at anti roll bar mounting point |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis at anti roll bar mounting point |2.4.A.3| | 1 |
| Power steering ram|s| leaking from a failed component |2.3.3b| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill / wheel arch - multiple (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill and wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill / wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill / wheel arch (7.1.1 (a) (i)) | 1 |
| Front Sub-frame corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Rear Sub-frame corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Rear Shock absorbers damaged to the extent that it does not function |5.3.2 |b|| | 1 |
| Offside Rear Suspension arm damaged and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Rear Upper Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Nearside Rear Upper Suspension arm corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Rear Exhaust has a major leak of exhaust gases joint at back box |7.1.2| | 1 |
| Nearside Headlamp aim beam image obviously incorrect bulb fitted incorrectly |1.8.A.1b| | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill) Marked yellow (6.1.1 (c) (i)) | 1 |
| Nearside Front Direction indicator incorrect colour white light (4.4.3 (a)) | 1 |
| Offside Front Direction indicator incorrect colour white light (4.4.3 (a)) | 1 |
| Nearside Headlamp light source and lamp not compatible aftermarket xenon kit fitted (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible aftermarket xenon kit fitted (4.1.4 (c)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sills corroded away leaving large holes (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis holed (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis holed (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting multiple holes in sills (6.2.2 (d) (i)) | 1 |
| Offside Front Electrical wiring deteriorated and bare wires exposed |1.9.2c| | 1 |
| Nearside Front Electrical wiring deteriorated and bare wires exposed |1.9.2c| | 1 |
| Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings body sill |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor pan chassis rail |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body sill (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded chassis rail |seat base| near brake pipes |5.2.6| | 1 |
| Nearside Front Integral body structure has excessive corrosion which adversely affects braking or steering inner wing /chassis |6.1.1 |c| |ii|| | 1 |
| Offside Front Integral body structure has excessive corrosion which adversely affects braking or steering inner wing/chassis |6.1.1 |c| |ii|| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Front Undertray insecure |8.1.1 |b| |i|| | 1 |
| Nearside Parking brake inoperative on one side low effort |1.4.1 |a|| | 1 |
| Offside Parking brake inoperative on one side low effort |1.4.1 |a|| | 1 |
| Nearside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting |6.2.2 |d| |i|| | 1 |
| Central Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting centre inner sill |6.2.2 |d| |i|| | 1 |
| Nearside Outer Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Inner Integral body structure is deformed and structural rigidity is significantly reduced chassis wing (6.1.1 (a) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill has corrosion (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Sill front to rear (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail. (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail. (6.2.2 (d) (i)) | 1 |
| Nearside Rear Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Valve stem seriously damaged All 4 valve stems (5.2.3 (j)) | 1 |
| Exhaust has a major leak of exhaust gases REAR |6.1.2 |a|| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system pipe goes across rear of vehicle leaking at offside joint (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced lower sill (7.1.1 (a) (i)) | 1 |
| Offside Front Braking system leaking caliper (1.1.3 (d)) | 1 |
| Offside Rear fog lamp not visible from a reasonable distance |1.1.6b| | 1 |
| Headlamp incorrect colour |4.1.4 |a|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded rear of outer sill |5.2.6| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength above upper suspention arm (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength holes in seal (5.3.6 (a) (i)) | 1 |
| Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Front Horn not working |7.7 |a| |ii|| | 1 |
| Front Supplementary restraint system warning lamp indicates a fault |7.1.6 |a|| | 1 |
| Outer Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Outer Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength flitch panel behind wheel holed |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength flitch panel behind wheel cracked |5.3.6 |a| |i|| | 1 |
| Nearside Front Braking system leaking caliper bleed nipple |3.6.A.1| | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system to passenger side rear brake hose (1.1.11 (b) (ii)) | 1 |
| Brake performance not tested due to leaking brake pipe (1.2.1 (g)) | 1 |
| Central Rear Tie bar/rod attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings marked in yellow |6.1.B.2| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Outer Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills and rear arch (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills and rear arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor/wheel arch behind rear wheel (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg at anti-roll bar mounting (5.3.6 (a) (i)) | 1 |
| Front Suspension arm corroded and seriously weakened both lower arms |2.4.G.1| | 1 |
| Rear Suspension arm corroded and seriously weakened both lower arms badly holed and corroded |2.4.G.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill area |small| |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded INNER SILL |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases CENTRE SECTION |7.1.2| | 1 |
| Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| brake caliper securing device excessively deteriorated ALL PARTIALLY SEIZED |3.5.1j| | 1 |
| Offside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings OUTER SILL |6.1.B.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded at outer sill |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded at outer sill
|5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill panel |5.2.6| | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper |1.1.16 |b| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Inner wing/ Chassis leg |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner sill/ floor pan |5.2.6| | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Track rod end ball joint has excessive play nut loose (2.1.3 (b) (i)) | 1 |
| Front Anti-roll bar linkage has excessive play in a ball joint both |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner arch/chassis leg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner arch corroded |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded backing sill |2.4.A.3| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor pan by sill / floor joint holed within 30 cm of seat mounting point. ( immediately in front of previous repair ) (6.2.2 (d) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced entire inner sill front to rear (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is inadequately repaired sill |7.1.1 |a| |i|| | 1 |
| Front Service brake excessively binding both |1.2.1 |f|| | 1 |
| Nearside Rear Parking brake efficiency less than 50% of the required value and offside (1.4.2 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point area (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill lower quarter (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sills |6.2.2 |d| |i|| | 1 |
| Offside Front Brake pipe at imminent risk of failure or fracture 2 pipes running together back to front |1.1.11 |a|| | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak back box (8.2.1.1 (b)) | 1 |
| Nearside Headlamp aim unable to be tested Bulb out (4.1.2 (b)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail in 2x areas (6.1.1 (c) (i)) | 1 |
| Central Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Brake performance not tested see pipe leaking (1.2.1 (g)) | 1 |
| Electrical wiring heavily deteriorated rear cable by axle broken (4.11 (b) (ii)) | 1 |
| Brake pipe leaking on a hydraulic braking system Front to rear pipe (1.1.11 (b) (ii)) | 1 |
| Power steering pipe|s| or hose|s| excessively damaged |2.3.2| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded floor/box section |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill x2 holes |5.2.6| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Front Lower Body insecure and dangerous to other road users wing |6.1.B.1b| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Offside Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
| Exhaust has a major leak of exhaust gases middle and rear joint corroded and leaking (6.1.2 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded middle floor |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded middle floor |5.2.6| | 1 |
| Nearside Front Lower Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Engine MIL inoperative or indicates a malfunction Inoperative (8.2.1.2 (h)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill structure (6.1.1 (c) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded |7.1.1 |a| |i|| | 1 |
| Central Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced offside (6.1.1 (c) (i)) | 1 |
| Central Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced nearside (6.1.1 (c) (i)) | 1 |
| Battery insecure and likely to fall from carrier in boot (4.13 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded body sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint likely to become detached loose (5.3.4 (a) (ii)) | 1 |
| Offside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Outer sill corroded |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded Inner sill corroded |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded Chassis rail corroded within area of sub frame mounting |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded Chassis rail corroded within area of sub fame mounting |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Chassis rail corroded within area of anti roll bar mount |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Chassis rail corroded within area of anti roll bar mount |2.4.A.3| | 1 |
| Offside Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Front Position lamp adversely affected by the operation of another lamp dipped and main beam (4.2.3 (c)) | 1 |
| Front Subframe mounting prescribed area is excessively corroded nearside & offside |2.4.A.3| | 1 |
| Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced nearside & offside |2.4.G.1| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor panel (7.1.1 (a) (i)) | 1 |
| Offside Rear Valve stem seriously misaligned |4.1.D.1e| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassic |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassic |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch x2 (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inenr sill x3 (7.1.1 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded wheel arch to sill |5.2.6| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering near anti roll bar mount (6.1.1 (c) (ii)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering near anti roll bar mount (6.1.1 (c) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases centre to rear silencer
|7.1.2| | 1 |
| Offside Front Anti-roll bar linkage ball joint likely to become detached detached |5.3.4 |a| |ii|| | 1 |
| Offside Rear Brake pipe modified and seriously weakened |3.6.A.3| | 1 |
| Offside Rear Tie bar/rod insecure |2.4.G.1| | 1 |
| Nearside Front Torsion bar insecure at an end fixing |2.4.E.2| | 1 |
| Offside Rear Vehicle structure has damage which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill end area |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill end area |5.2.6| | 1 |
| Offside Rear Stop lamp(s) adversely affected by the operation of another lamp Staying on with sidelights (4.3.3 (b)) | 1 |
| Central Rear Stop lamp(s) adversely affected by the operation of another lamp Staying on with side lights (4.3.3 (b)) | 1 |
| Nearside Rear Stop lamp(s) likely to become detached Staying on with sidelights (4.3.1 (c) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill area |5.2.6| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits too high 1.044 & 1.038 |7.3.D.3| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive too high 0.33 |7.3.D.3| | 1 |
| Nearside Front Passenger`s seat insecure |6.2.A.1| | 1 |
| Nearside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded front of top arm |2.4.A.3| | 1 |
| Nearside Brake cable insecure |3.5.1d| | 1 |
| Offside Brake cable insecure |3.5.1d| | 1 |
| Nearside Front Anti-roll bar linkage fractured |5.3.3 |b| |ii|| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded UNDERSIDE SILL |5.2.6| | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded rear outer sill/end |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded rear outer sill /end |5.2.6| | 1 |
| Nearside Rear Upper Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Lower Anti-roll bar linkage has excessive play in a ball joint broken |2.4.G.2| | 1 |
| Offside Rear Upper Brake pipe leaking |3.6.A.1| | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak exhaust box |8.2.1.1 |b|| | 1 |
| Exhaust has a major leak of exhaust gases Centre section join blowing (6.1.2 (a)) | 1 |
| Emissions unable to be completed major exhaust blow (8.2.1.2 (d)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected wing (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Direction indicator obviously incorrectly positioned (4.4.3 (a)) | 1 |
| Offside Body has a sharp edge caused by corrosion inner sill marked with chalk |6.1.C.1| | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer body sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer body sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded near to seat and seatbelt mount , rear suspension mount (6.1.1 (c) (i)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced central sill corroded near to seat mount (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering chassis rail near to ARB mount (6.1.1 (c) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill floor pan |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill floor pan |5.2.6| | 1 |
| Offside Front Road wheel more than one fixing missing 2 nuts (5.2.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill holed and corroded (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is severely distorted |5.2.6| | 1 |
| Braking system leaking front to rear pipe excessive corrosion |3.6.A.1| | 1 |
| Centre Rear Parking brake lever defective so that it cannot be satisfactorily operated |3.1.3c| | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system by retaining clip (1.1.11 (b) (ii)) | 1 |
| Power steering inoperative |2.1.5 |c| |i|| | 1 |
| Braking system leaking caliper |3.6.A.1| | 1 |
| Rear Fuel pipe union leaking |7.2.3| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering front and centre chassis legs both nearside and offside . |6.1.A.1| | 1 |
| Offside Rear Lower Body has a sharp edge caused by corrosion rear wheel arch |6.1.C.1| | 1 |
| Nearside Rear Lower Body has a sharp edge caused by corrosion wheelarch |6.1.C.1| | 1 |
| Fuel pipe insecure |7.2.1| | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill to floor area (6.1.1 (c) (i)) | 1 |
| Nearside Rear Floor in such a condition it is likely to cause load insecurity or instability Boot floor (6.2.4 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Floor. (7.1.1 (a) (i)) | 1 |
| Emissions not tested excess water in vehicle exhaust causing EGA to abort test |8.2.1.2 |d|| | 1 |
| Front Front position lamp|s| incorrect colour x2 |1.1.A.3e| | 1 |
| Nearside Rear Anti-roll bar damaged and seriously weakened |2.4.G.1| | 1 |
| Emissions unable to be completed clearly in excess of limits (8.2.1.2 (d)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg holed on outer face and under near suspension arm (5.3.6 (a) (ii)) | 1 |
| Rear Window in an unacceptable condition view out back window stickers covering view (3.2 (c) (i)) | 1 |
| Brake lever has insufficient reserve travel handbrake (1.1.2 (a)) | 1 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Emissions unable to be completed reading to high and messing machine up (8.2.1.2 (d)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Floor excessively deteriorated floor rail holed (6.2.4 (a) (i)) | 1 |
| Nearside Front Lower Floor excessively deteriorated floor rail holed (6.2.4 (a) (i)) | 1 |
| Rear Parking brake efficiency below requirements no readings esp at n/s/r (1.4.2 (a) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases leaking at join (6.1.2 (a)) | 1 |
| Steering box leaking to the extent that oil is dripping (2.1.1 (e) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill and inner sill. (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill to floor. (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired inner arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis by anti-roll bar |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis by anti-roll bar |5.3.6 |a| |i|| | 1 |
| Suspension component mounting prescribed area is excessively corroded nearside front inner arch |2.4.A.3| | 1 |
| Electrical wiring damaged, likely to cause a short |1.9.2b| | 1 |
| Front Road wheel fixing missing both sides wheel nut missing |5.2.1 |a| |i|| | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch |6.1.1 |c| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded floor. |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor. |5.2.6| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced at outer sill (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre and rear |7.1.2| | 1 |
| Nearside Rear Outer Seat belt insecurely fixed to the vehicles structure sill |5.2.1a| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded centre floor |5.2.6| | 1 |
| Nearside Front Brake hose damaged and likely to fail |1.1.12 |a|| | 1 |
| Offside Front Brake hose damaged and likely to fail |1.1.12 |a|| | 1 |
| Emissions not tested low oil (8.2.1.2 (d)) | 1 |
| Offside Rear Inner Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill at rear and centre |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg in several places |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg in several places |5.3.6 |a| |i|| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.06 (8.2.1.2 (c)) | 1 |
| Exhaust has a major leak of exhaust gases cat join area (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis - marked in yellow - viewed from inner arch - anti-roll bar & upper arm mount prescribed area (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under side of chassis - anti-roll bar & upper arm mount prescribed area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under side of chassis - anti-roll bar & upper arm mount prescribed area (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn play found when vehicle is jacked on the lower arms (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn play found when vehicle is jacked on the lower arms (5.3.4 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch areas (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect no beam pattern visible - headlamp weathered (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect no beam pattern visible - headlamp weathered (4.1.2 (c)) | 1 |
| Nearside Brake lever has restricted free movement |3.5.1k| | 1 |
| Offside Brake lever has restricted free movement |3.5.1k| | 1 |
| Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases
joint |7.1.2| | 1 |
| Offside Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Windscreen wiper missing (3.4 (a)) | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting insecure brace loose (5.3.3 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Inner sill |5.2.6| | 1 |
| Nearside Front Lower Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Headlamp not working on dipped beam NEARSIDE |1.7.5a| | 1 |
| Exhaust has a major leak of exhaust gases CENTRE |7.1.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded Floor |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer cill |5.2.6| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassie |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassie |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill within 30 cms of a |2.4.A.3| | 1 |
| Offside Front Outer Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength sill within 30 cms of a |2.4.A.3| | 1 |
| Front Position lamp not working Both sides |4.2.1 |a|| | 1 |
| Nearside Headlamp lens seriously defective Deteriorated (4.1.1 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis box section (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Under wheel arch behind plastic cover (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases joint section |6.1.2 |a|| | 1 |
| Valve stem seriously damaged Nearside front perished |4.1.D.1e| | 1 |
| Position lamp not working Nearside front (4.2.1 (a) (ii)) | 1 |
| Nearside Headlamp not working on dipped beam Poor connection |4.1.1 |a| |ii|| | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light white light to rear (4.5.4 (a)) | 1 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases silencer near rear axle |7.1.2| | 1 |
| Rear Suspension component attachment bracket/mounting insecure and impairing directional stability suspension brace bars not attached at rear (5.3.3 (a) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases pipe to box broken (6.1.2 (a)) | 1 |
| Emissions unable to be completed exhaust condition (8.2.1.2 (d)) | 1 |
| Brake pedal has insufficient reserve travel pedal creeping down (1.1.2 (a)) | 1 |
| Offside Rear Suspension arm worn and seriously weakened |2.4.G.1| | 1 |
| Nearside Front Seat belt damaged (7.1.2 (b) (i)) | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits high |7.3.D.3| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill |5.3.6 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill mid floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension arm insecure and impairing directional stability front bolt loose (5.3.3 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced front floor and chassis member as marked (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill corroded and holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Brake hose bulging under pressure and leaking (1.1.12 (d)) | 1 |
| Central Exhaust has a major leak of exhaust gases has been previously welded |6.1.2 |a|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Drivers door cannot be opened from inside the vehicle when window is down (6.2.3 (a)) | 1 |
| Drivers door cannot be opened from outside the vehicle when window is down (6.2.3 (a)) | 1 |
| Offside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Inner sill |5.3.6 |a| |ii|| | 1 |
| Rear Braking system leaking brake pipe T piece |3.6.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail within 30cm of anti roll bar mount |2.4.A.3| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill holed & corroded |6.1.1 |c| |i|| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill holed & corroded |6.1.1 |c| |i|| | 1 |
| Rear Anti-roll bar pin or bush excessively worn both, mounts (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn drop link |5.3.4 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer lower sill/ Body (7.1.1 (a) (i)) | 1 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced dim |1.7.5a| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill back (5.3.6 (a) (i)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Power steering pipe|s| or hose|s| leaking on rack |2.3.3b| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam bulb (4.1.1 (a) (ii)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both lenses cleaned (4.1.4 (b)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt upper arm ball joint (5.3.4 (b) (ii)) | 1 |
| Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Rear Sub-frame attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| coil spring incomplete |2.4.C.1a| | 1 |
| Position lamp not working both front |4.2.1 |a| |ii|| | 1 |
| Nearside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Nearside Front Upper Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch inner (7.1.1 (a) (i)) | 1 |
| Nearside Side repeater likely to become detached (4.4.1 (c) (ii)) | 1 |
| Front Horn not working (7.7 (a) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rail in front of subframe (6.2.2 (d) (i)) | 1 |
| Offside Rear Floor excessively deteriorated damaged crushed upwards (6.2.4 (a) (i)) | 1 |
| Offside Rear Suspension arm attachment bracket/mounting missing to floor pan (5.3.3 (a) (ii)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases rear centre box (6.1.2 (a)) | 1 |
| Nearside Body component insecure oversill (6.2.1 (a) (i)) | 1 |
| Offside Body component insecure oversill (6.2.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre and rear holed (6.1.2 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill, sill cover fixing corroded and holed |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill, sill cover fixing corroded and holed |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded inner sill holed |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded By anti roll bar d bush???s |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded By anti roll bar d bush???s |2.4.A.3| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 1 |
| Headlamp not working on dipped beam nearside and offside (4.1.1 (a) (ii)) | 1 |
| Headlamp not working on main beam nearside and offside (4.1.1 (a) (ii)) | 1 |
| Fuel cap/sealing device ineffective non standard non locking (6.1.3 (b) (i)) | 1 |
| Rear Brake disc significantly and obviously worn nearside and offside (1.1.14 (a) (i)) | 1 |
| Brake pedal reservoir fluid level decreases after several brake applications |3.3.C.1| | 1 |
| Nearside Outer Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill half length (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg by Anti roll bar mount (5.3.6 (a) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis leg floor area (6.1.1 (c) (i)) | 1 |
| Power steering pipe/hose leaking Pipe on rack (2.1.5 (a)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced as marked in yellow |6.1.1 |c| |i|| | 1 |
| Nearside Rear Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Emissions not tested due to no catalist |7.3.A.1| | 1 |
| Headlamp aim projected beam image is obviously incorrect both front due to misting (4.1.2 (c)) | 1 |
| Brake performance not tested due to binding (1.2.1 (g)) | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened shock absorber mount (5.3.3 (b) (i)) | 1 |
| Nearside Vehicle structure is deformed and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced out rigger (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer and inner sills holed (7.1.1 (a) (i)) | 1 |
| Steering system fouling |2.2.D.2a| | 1 |
| Exhaust has a major leak of exhaust gases join |7.1.2| | 1 |
| Nearside Front Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg chalk marked |6.1.B.2| | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Emissions NOx sensor obviously defective (8.2.1.1 (a)) | 1 |
| Front Position lamp not working both, (4.2.1 (a) (ii)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits FUEL SYSTEM CLEANER WAS ADDED (8.2.1.2 (b)) | 1 |
| Rear Inner Brake disc in such a condition that it is seriously weakened both sides, (1.1.14 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on dipped beam headlamp on mainbeam when nearside is at dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Upper Suspension arm attachment bracket/mounting likely to become detached nut loose (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Lower Suspension arm attachment bracket/mounting likely to become detached nut loose (5.3.3 (a) (ii)) | 1 |
| Offside Rear Shock absorbers likely to become detached lower nut missing (5.3.2 (a) (ii)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |6.1.1 |c| |ii|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis |6.1.1 |c| |ii|| | 1 |
| Offside Rear Lower Suspension rod insecurely attached bolt loose |5.3.3 |a| |i|| | 1 |
| Emissions unable to be completed Exhaust centre to rear system broken & gases escaping early (8.2.1.2 (d)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor holed |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded rear inner sill holed & corroded |5.2.6| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak back box (8.2.1.1 (b)) | 1 |
| Offside Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Front Brake pipe inadequately clipped to rear gearbox area |3.6.B.1| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner and outer sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis,under wheel arch. |5.3.6 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/floor near seat mounting. |7.1.1 |a| |i|| | 1 |
| Offside Front Body component corroded and likely to cause injury sharp edge at wing. |6.2.1 |a| |i|| | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced side sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Upper Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Upper Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Lower Steering linkage ball joint has excessive play |2.1.3 |b| |i|| | 1 |
| Brake hose leaking |3.6.A.1| | 1 |
| Drivers view of an obligatory external mirror materially affected by an obstruction (3.1 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened under and outer holed (5.3.3 (b) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired outer sill and under sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill and under sill and inner sill end cap and inner wheel arch rear (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under floor to under sill rear (5.3.6 (a) (i)) | 1 |
| Nearside Front Steering arm fractured (2.1.3 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre jiont |7.1.2| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced belt mountig (7.1.1 (a) (i)) | 1 |
| Offside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill holed x2 (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor pan/battery tray holed exposing battery (6.2.2 (d) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded above spring location |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded above spring location |2.4.A.3| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion front lower arch. |6.1.C.1| | 1 |
| Offside Outer Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Rear Sub-frame attachment bracket/mounting insecure rear crossmember bolt sheared off. |2.4.G.1| | 1 |
| Nearside Rear Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced and outer sill |7.1.1 |a| |i|| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor/sill |7.1.1 |a| |i|| | 1 |
| Offside Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Rear Parking brake not fitted on at least two wheels |3.1.1| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded under vehicle chassis rail |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill area |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis under wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis area under wheelarch |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill section |5.2.6| | 1 |
| Stop lamp(s) not working center (4.3.1 (a) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded inner cill |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Nearside Rear Service brake grabbing severely |1.2.1 |c|| | 1 |
| Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Offside Rear Braking system leaking calliper |3.6.A.1| | 1 |
| Offside Direction indicators not working |1.4.A.2c| | 1 |
| Offside rear brakes release unevenly |3.7.B.4| | 1 |
| Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Coil spring fractured or broken both rear (5.3.1 (b) (i)) | 1 |
| Power steering pipe/hose leaking metal pipe leaking (2.1.5 (a)) | 1 |
| Emissions not tested no O2 registering due to break in exhaust system (8.2.1.2 (d)) | 1 |
| Nearside Position lamp has a product on the lens or light source which shows white light to the rear (4.2.3 (b) (ii)) | 1 |
| Offside Position lamp has a product on the lens or light source which shows white light to the rear (4.2.3 (b) (ii)) | 1 |
| Fuel cap/sealing device ineffective flap does not release effectively from inside vehicle (6.1.3 (b) (i)) | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases centre to rear joint detached ( corroded) (6.1.2 (a)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Brake pipe leaking on an air braking system front to rear (1.1.11 (b) (i)) | 1 |
| Front Service brake indicates brake judder |3.7.D.1| | 1 |
| Offside Rear Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section above lower arm (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section above lower arm (5.3.6 (a) (i)) | 1 |
| Offside Rear Exhaust emissions likely to be affected by an exhaust leak REAR SILENCER CORRDED AND LEAKING (8.2.1.1 (b)) | 1 |
| Rear Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 1 |
| Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |sill| |6.2.2 |d| |i|| | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |sill| |6.2.2 |d| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor |marked| |5.2.6| | 1 |
| Brake lever has insufficient reserve travel handbrake |1.1.2 |a|| | 1 |
| Nearside Anti-roll bar linkage missing |2.4.G.1| | 1 |
| coil spring broken |2.4.C.1a| | 1 |
| brake caliper has restricted free movement |3.5.1k| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wing. |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill and inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill inner and outer and inner wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Brake hose leaking on a hydraulic braking system front flexi banjo leaking to caliper connection (1.1.12 (c) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch end of sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch end of sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Body insecure sill plate insure at bottom (6.2.2 (a) (i)) | 1 |
| Nearside Rear Body insecure outer sill has a small hole (6.2.2 (a) (i)) | 1 |
| Dipswitch does not operate immediately when selected on main beam arm bent back too far cannot seclect main beam (4.1.3 (b)) | 1 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill corroded |7.1.1 |a| |i|| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced o/s sill corroded at rear (7.1.1 (a) (i)) | 1 |
| Nearside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Rear coil spring broken both sides, |2.4.C.1a| | 1 |
| Offside Front Brake pipe excessively damaged TO REAR (1.1.11 (c)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis rail at anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings lower chasis leg |6.1.B.2| | 1 |
| Offside Front Shock absorbers insecurely attached lower nut |5.3.2 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting weld cracked |2.4.G.1| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` 2 , ns and centre |8.3.1e| | 1 |
| Offside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
| Offside Rear Anti-roll bar linkage inappropriately repaired |2.4.A.2| | 1 |
| Rear Electrical wiring insulation in such a condition there is an imminent risk of fire or formation of sparks |4.11 |c| |iii|| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill... |6.1.B.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill.... |6.1.B.2| | 1 |
| Nearside Rear Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits CO 0.77% |8.2.1.2 |b|| | 1 |
| Emissions not tested due to over heating |7.3.A.1| | 1 |
| Nearside Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Hydraulic fluid leaking excessively |8.4.1 |a| |i|| | 1 |
| Nearside Front Front position lamp|s| incorrect colour side light blue |1.1.A.3e| | 1 |
| Offside Front Front position lamp|s| incorrect colour side light blue |1.1.A.3e| | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Rear Sub-frame attachment bracket/mounting insecure nearside / offside excessively corroded |5.3.3 |a| |i|| | 1 |
| Nearside Front Macpherson strut corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded centre inner sill marked |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill marked yellow |5.2.6| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill marked yellow |5.2.6| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor /sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure is deformed and structural rigidity is significantly reduced chassis inner arch wishbone mounting (6.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure is deformed and structural rigidity is significantly reduced chassis wishbone mounting (6.1.1 (a) (i)) | 1 |
| Offside Front Lower Body panel corroded and likely to cause injury wing /sill (6.2.1 (a) (i)) | 1 |
| Power steering component|s| leaking from a failed seal rack |2.3.3b| | 1 |
| Brake performance unable to be tested fluid leak (1.2.1 (g)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both sides outer (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor significant corrosion (7.1.1 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer chassis (6.1.1 (c) (i)) | 1 |
| Battery insecure and likely to fall from carrier battery tray compartment corroded (4.13 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor ang sill to floor (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor and floor to sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar missing anti roll bar link |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassic (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassic (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint likely to become detached HAS DETACHED |5.3.4 |a| |ii|| | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded lower outer sill holed |5.2.6| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill 30cm seat mount |6.2.2 |d| |i|| | 1 |
| Nearside Front Anti-roll bar linkage fractured broken (5.3.3 (b) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer holed and blowing, (6.1.2 (a)) | 1 |
| Offside Front Position lamp not working replaced 501 capless bulb |4.2.1 |a|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is deliberately modified which significantly reduces the original strength |5.2.6| | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak |8.2.2.1 |b|| | 1 |
| Offside Rear Parking brake lever inoperative |1.1.6 |d|| | 1 |
| Central Emission control equipment obviously defective (8.2.1.1 (a)) | 1 |
| Nearside Rear position lamp|s| incorrect colour Lens broken allow white light to show |1.1.A.3e| | 1 |
| Offside Track rod end ball joint worn to the extent there is a serious risk of detachment |2.1.3 |b| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer body sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti roll bar |5.3.6 |a| |i|| | 1 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Inner Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Brake pipe connection leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 1 |
| Centre Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Inner wheel arch |5.2.6| | 1 |
| Stop lamp(s) not working both sides (4.3.1 (a) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front inner wings under car (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced offside and nearside floor (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded roll bar mounting |2.4.A.3| | 1 |
| Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
| Front Brake lining(s) less than 1.5 mm thick (1.1.13 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chssis rail by anti roll bar mount |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded sill panel |5.2.6| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Central Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Offside Rear Sub-frame attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Driver`s seat insecure |6.2.A.1| | 1 |
| Emissions unable to be completed due to cat missing (8.2.1.2 (d)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis holed by shock absorber |2.4.A.3| | 1 |
| Front Fluid leak harmful to the environment or a risk to other road users engine area but under tray fitted cant pin point (8.4.1 (a) (i)) | 1 |
| Rear Exhaust system insecure Rubber mountings /both sides (6.1.2 (a)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded Marked [Floor} |5.2.6| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer sill, within seat & belt mounting area. (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis leg area |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor pan/inner sill area |5.2.6| | 1 |
| Offside Front Anti-roll bar linkage insecurely attached broken off |5.3.3 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at upper suspension arm mounting point marked yellow |5.3.6 |a| |i|| | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits CO2 Emissions Exceeding Legal Limit Both At Idle & During Fast Idle Test (8.2.1.2 (b)) | 1 |
| Service brake grabbing severely N/S/F Wheel Grabbing/Binding (1.2.1 (c)) | 1 |
| Brake performance not tested RBT Test Not Performed Due To N/S/F Wheel Binding On (1.2.1 (g)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits Emissions Limits Not Met During Test (8.2.1.2 (b)) | 1 |
| Front Brake pipe leaking - rear |3.6.A.1| | 1 |
| Offside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner arch area (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner and outer sill |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill (7.1.1 (a) (i)) | 1 |
| Central Rear Inner Brake pipe inadequately supported Brake bracket damaged |3.6.B.1| | 1 |
| Offside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Brake pivot has restricted free movement |3.5.1k| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area corroded/holed (7.1.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn not done up? (5.3.4 (a) (i)) | 1 |
| Nearside Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area is fractured Chassis rail |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded antiroll bar mount |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded centre, inner and outer sill |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area is fractured sill |5.2.6| | 1 |
| Nearside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Exhaust emissions hydrocarbon content excessive car standing test drive with additive now within spec (8.2.1.2 (b)) | 1 |
| Central Front Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Emissions unable to be completed Hi Rev. (8.2.1.2 (d)) | 1 |
| Emissions not tested due to engine mis-fire |7.3.A.1| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill an floor |6.1.B.2| | 1 |
| Offside Rear Upper Suspension arm rubber bush deteriorated resulting in excessive movement Outer bush |2.4.G.2| | 1 |
| Emissions not tested over heating |7.3.A.1| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded Floor |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Floor |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Floor |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded Floor |2.4.A.3| | 1 |
| Offside Front Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis |5.3.3 |b| |i|| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened chassis |5.3.3 |b| |i|| | 1 |
| Offside Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Centre Rear Braking system leaking |3.6.A.1| | 1 |
| Rear Anti-roll bar linkage has excessive play in a ball joint n/s o/s |2.4.G.2| | 1 |
| Sub-frame corroded and seriously weakened strengthening bar (5.3.3 (b) (i)) | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings FLOOR TO SILL |6.1.B.2| | 1 |
| Offside Rear Lower Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Brake lever has restricted free movement |3.5.1k| | 1 |
| Braking system leaking n/s/r brake caliper |3.6.A.1| | 1 |
| Headlamp switch insecure |1.7.1| | 1 |
| Exhaust has a major leak of exhaust gases complete exhaust system rotten and various leaks - front and rear (6.1.2 (a)) | 1 |
| Nearside Track rod end modification unsafe split pin missing from castle nut (2.1.3 (f) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded lower sil |5.2.6| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded lowe sill |5.2.6| | 1 |
| Front Exhaust has a major leak of exhaust gases and rear |6.1.2 |a|| | 1 |
| Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside brake caliper has restricted free movement |3.5.1k| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect due to misted lens |1.8.A.1b| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect due to misted lens |1.8.A.1b| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mounting arear chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill repair has been folded around a corroded panel not welded (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill repair panel has become detached along bottom edge (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill corroded and holed where it meets the floor panel within 30cm of seat mounting (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill holed and corroded where it meets the floor panel within 30cm of seat belt mounting (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis section |2.4.A.3| | 1 |
| Emissions not tested vehicle overheating, emissions aborted to save engine damage (8.2.1.2 (d)) | 1 |
| Headlamp aim projected beam image is obviously incorrect bulb fitted wrong way (4.1.2 (c)) | 1 |
| Offside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Inner Front Road wheel bead rim badly distorted |4.2.A.1a| | 1 |
| Offside Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Rear Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt link |2.4.G.2| | 1 |
| Front Service brake excessively fluctuating both brakes (1.2.1 (e)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced three foot section (6.1.1 (c) (i)) | 1 |
| Steering wheel likely to become detached (2.2.1 (b) (ii)) | 1 |
| Rear Engine mounting bracket damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
| Fuel system component leaking |6.1.3 |b| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Anti roll bar mount |5.3.6 |a| |i|| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive requires CAT |7.3.D.3| | 1 |
| Valve stem seriously damaged all (5.2.3 (j)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis area |2.4.A.3| | 1 |
| Offside Rear Braking system leaking at caliper area |3.6.A.1| | 1 |
| Offside Headlamp light intensity severely reduced dipped beam (4.1.4 (a)) | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened at shocker attachment (5.3.3 (b) (i)) | 1 |
| Offside Front Shock absorbers has an excessively worn bush lower bush (5.3.2 (c)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor chalked (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near front to rear pipes (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within 30cm of strut top moutinng (5.3.6 (a) (i)) | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill excessively corroded (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill excessively corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis @ subframe and antiroll bar mounting areas (5.3.6 (a) (i)) | 1 |
| Nearside Steering component deformed and unserviceable track rod |2.2.C.1d| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassie (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting front of wheel arch (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing behind shock absorber mount |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded front of shock absorber mount |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded top of chassis leg |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded top of chassis leg |2.4.A.3| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill near wheel arch & corrosion below o/s door on sill (7.1.1 (a) (i)) | 1 |
| Front Brake fluid warning lamp illuminated |3.6.G.2| | 1 |
| Centre Front Braking system leaking |3.6.A.1| | 1 |
| Rear Fuel system component leaking fuel filter leaking (6.1.3 (b) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both side sills (7.1.1 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both side sills (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded OS sill corroded by seat and seat belt mount |5.2.6| | 1 |
| Fluid leak harmful to the environment or a risk to other road users PAS leak from steering rack pipe |8.4.1 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner chassis leg |5.3.6 |a| |i|| | 1 |
| Offside Front Road wheel fractured |4.2.B.1a| | 1 |
| Offside Front Suspension arm attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Front Lower Anti-roll bar ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint and offside rear |2.4.G.2| | 1 |
| Nearside Rear Upper Suspension arm rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering above anti roll bar mount |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering above offside front anti roll bar mount |6.1.A.1| | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering chassis in 2 places |6.1.A.1| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floors to sills |6.1.B.2| | 1 |
| Nearside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings lower Body inner sill close to front seat mount has a hole and corrosion. |6.1.B.2| | 1 |
| Offside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings lower Body inner sill close to front seat mount has a hole and corrosion. |6.1.B.2| | 1 |
| Nearside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Body close to suspension and sub-frame mount has hole and excessive corrosion. |6.1.B.2| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced central inner (7.1.1 (a) (i)) | 1 |
| Offside Front Braking system leaking calaper |3.6.A.1| | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement broken |2.4.G.2| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 1 |
| Nearside Rear Anti-roll bar linkage corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti-roll bar mounting |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded anti-roll bar mounting |2.4.A.3| | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting missing bolt broken (5.3.3 (a) (ii)) | 1 |
| Nearside Front Upper Suspension arm insecurely attached ball joint locking device missing (5.3.3 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Headlamp does not operate immediately when selected on main beam |1.7.4a| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch/chassis |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch/chassis |6.1.B.2| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Central Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced OSF Front Chassis area under drivers feet (6.1.1 (c) (i)) | 1 |
| Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt Nearside front (5.3.4 (b) (ii)) | 1 |
| Anti-roll bar linkage ball joint excessively worn Nearside front (5.3.4 (a) (i)) | 1 |
| Offside Front Brake pipe fouled by moving parts from master cylinder |3.6.B.2a| | 1 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings & outer sill |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floorpan to inner sill |6.1.B.2| | 1 |
| Nearside Front suspension locking device missing & offside front outer lower balljoints |2.5.A.4| | 1 |
| Nearside Headlamp not working on dipped beam LLB472 bulb replaced to pass (4.1.1 (a) (ii)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Outer Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Offside Front Outer Suspension component mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
| Nearside Front Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 1 |
| Nearside Front Power steering component|s| leaking |2.3.3b| | 1 |
| Offside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Lower Suspension component mounting prescribed area is inadequately repaired rear sill and rear quarter pannel |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area is inadequately repaired outer sill |5.3.6 |a| |i|| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded floor pan excessively corroded adjacent to seat |5.2.6| | 1 |
| Rear Exhaust system not adequately supported silencer box |7.1.1| | 1 |
| Fuel cap/sealing device component leaking (6.1.3 (b) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Outer Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Front Outer Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Front Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch |6.1.B.2| | 1 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch |6.1.B.2| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases mid and rear sections |6.1.2 |a|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear inner sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired rear sill closing panel corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced rear sill closing panel corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail corroded (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail corroded (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system brake pipe n/s rear bust on brake test (1.1.11 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage damaged and seriously weakened snapped |2.4.G.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Outer Sill And Sill End |5.2.6| | 1 |
| Front Service brake excessively fluctuating both brakes n/s and o/s (1.2.1 (e)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill/ quarter panel area (7.1.1 (a) (i)) | 1 |
| Emissions not tested due to coolant leak |8.2.1.2 |d|| | 1 |
| Nearside Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Subframe mounting prescribed area is excessively corroded both rear outer sills |2.4.A.3| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting n/s/f inner wheel arch corroded |6.2.2 |d| |i|| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting n/s/r outer door sill corroded |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor. (6.1.1 (c) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch. (5.3.6 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill marked in yellow |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases centre silencer (6.1.2 (a)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SILL CORROSION. (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed EXHAUST LEAK. (8.2.1.2 (d)) | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded Chassis |inner wing| |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded Inner wing |Chassis| |2.4.A.3| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SILL |7.1.1 |a| |i|| | 1 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn Outer. (5.3.4 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm pin or bush excessively worn Outer. (5.3.4 (a) (i)) | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings at brake pipe brackets |6.1.B.2| | 1 |
| Seat belt anchorage prescribed area is excessively corroded both rear outter sills |5.2.6| | 1 |
| Nearside Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill. |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill. |5.2.6| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor to inner sill (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Floor to inner sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength REAR SILL END (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Suspension component mounting prescribed area is excessively corroded chassis corrosion hole |2.4.A.3| | 1 |
| Side repeater incorrect colour |1.4.A.2f| | 1 |
| Nearside Front passenger door does not latch securely closed |6.2.B.1a| | 1 |
| Nearside Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits engine overheated on emissions test (8.2.1.2 (a)) | 1 |
| Offside Headlamp reflector seriously defective no beam pattern (4.1.1 (b) (ii)) | 1 |
| Emissions not tested ABORTED DUE TO VEHICLE OVERHEATED (8.2.1.2 (d)) | 1 |
| Offside Front Anti-roll bar linkage insecure and impairing directional stability broken (5.3.3 (a) (ii)) | 1 |
| Rear passenger door does not latch securely closed |6.2.B.1a| | 1 |
| Offside Rear Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor holed as marked |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill holes as marked in two places |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor as marked |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill / floor as marked |5.2.6| | 1 |
| Offside Front Road wheel fixing loose |5.2.1 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill x 3 (5.3.6 (a) (i)) | 1 |
| Rear Electrical wiring damaged, likely to become detached Earth strap |1.9.2b| | 1 |
| Offside Front Front position lamp|s| not working new bulb fitted |1.1.A.3b| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded outer door sill |5.2.6| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush track rod |2.4.G.2| | 1 |
| Nearside Rear Road wheel fractured (5.2.2 (a)) | 1 |
| Rear Exhaust system not adequately supported n/s and o/s/r supports broken |7.1.1| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis leg near anti roll bar mounting |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body sill |5.3.6 |a| |i|| | 1 |
| Headlamp aim projected beam image is obviously incorrect both |4.1.2 |c|| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid caliper leaking fluid |1.1.16 |b| |i|| | 1 |
| Offside Front Electrical wiring insecure and connectors likely to become disconnected head lamp connector damaged effecting dip & main beam (4.11 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Wheelarch |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded Wheelarch |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded Outer sill |2.4.A.3| | 1 |
| Offside Inner Front Road wheel badly damaged |4.2.A.1a| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill x2 (7.1.1 (a) (i)) | 1 |
| Power steering component leaking resivour |2.1.5 |a|| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded sil |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases centre joint from CAT to rear section. |6.1.2 |a|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner cil. |7.1.1 |a| |i|| | 1 |
| Offside Front Shock absorbers insecurely attached |5.3.2 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sil |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded upper chassis |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired upper chassis |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired upper chassis |2.4.A.3| | 1 |
| Nearside Front Upper Front suspension locking device missing ball joint split pin missing |2.5.A.4| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill with in 30cm of seat belt mount (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength floor to sill with in30 cm of mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill section. (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill section. (7.1.1 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits 0.44 closest. (8.2.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill section. |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength chassis |within 30cm of roll bar mounting point| |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded under arch area |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner suspension mounting area. |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area fractured significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 1 |
| Windscreen in such a condition that visibility through swept area is seriously affected (3.2 (c) (ii)) | 1 |
| Rear Brake disc contaminated both rear (1.1.14 (b)) | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion Wheel arch |6.1.C.1| | 1 |
| Lower Steering column universal joint has excessive play |2.1.5| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded as marked |2.4.A.3| | 1 |
| Emissions not tested due to co to high and lamda to high |7.3.A.1| | 1 |
| Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings lower inner body or under sill has a corrosion |6.1.B.2| | 1 |
| Emissions not tested Engine cut out during emissions test |8.2.1.2 |d|| | 1 |
| Rear Exhaust has a major leak of exhaust gases at joint |7.1.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis inside wheel arch |2.4.A.3| | 1 |
| Nearside Steering locking device missing track rod end split pin missing |2.1.3 |d|| | 1 |
| Offside Steering locking device missing track rod end lock nut split pin missing |2.1.3 |d|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing area |5.3.6 |a| |i|| | 1 |
| Steering locking device missing split pins missing from o/s and n/s front upper and lower ball joints |2.1.3 |d|| | 1 |
| Nearside Front Coil spring not correctly located |2.4.C.2| | 1 |
| Passenger`s airbag obviously defective |5.4.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Inner sill |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded panFloor s |5.2.6| | 1 |
| Nearside Front Front position lamp|s| incorrect colour Blue bulb |1.1.A.3e| | 1 |
| Offside Front Front position lamp|s| incorrect colour Blue bulb |1.1.A.3e| | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner cill |6.1.1 |c| |i|| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner cill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Tie bar/rod locating pin insecure |2.4.G.3a| | 1 |
| Offside Outer Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Lower Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
| Brake pedal has insufficient reserve travel spongy (1.1.2 (a)) | 1 |
| Rear Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting out and inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
| Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
| front brake binding offside front |3.7.B.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Underside, inner arch marked yellow (5.3.6 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Underside, inner arch marked yellow (6.1.1 (c) (i)) | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded under wing |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced X2 (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Power steering pipe|s| or hose|s| leaking on front of rack |2.3.3b| | 1 |
| Nearside Front Suspension component mounting prescribed area is fractured chassis |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is fractured chassis |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases Major exhaust leak on rear joint (6.1.2 (a)) | 1 |
| Nearside Parking brake inoperative on one side Park brake inoperative on N/S. Brake caliper seized. (1.4.1 (a)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill marked (5.3.6 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases to centre section (6.1.2 (a)) | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre floor small hole |6.1.B.2| | 1 |
| Emissions not tested engine missfire |8.2.1.2 |d|| | 1 |
| Nearside Windscreen wiper missing |3.4 |a|| | 1 |
| Front Bumper damaged and likely to cause injury when grazed or contacted number plate surround damaged sharp edge (6.1.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover missing upper and lower (5.3.4 (b) (ii)) | 1 |
| Inner Rear brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch - within 30cm of top mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded Outer Sill |5.2.6| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering o/s/r outer sill |6.1.A.1| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering n/s/r outer sill |6.1.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill to wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill to wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Hydraulic brake calliper insecurely mounted (1.1.16 (c) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced underfloor to outer sill (7.1.1 (a) (i)) | 1 |
| Front Seat belt anchorage prescribed area strength or continuity significantly reduced Both underfloors (7.1.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outter sill to wheel arch |6.1.1 |c| |i|| | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering rear sill (6.1.1 (c) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases Back box joint |6.1.2 |a|| | 1 |
| Offside Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Offside Front Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Offside Rear Parking brake inoperative on one side + nsr low (1.4.1 (a)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer + inner sill (7.1.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases bracket/ pipe (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg side + underside (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg underside (5.3.6 (a) (i)) | 1 |
| Rear Service brake excessively fluctuating both sides (1.2.1 (e)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill end |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg as chalked |5.3.6 |a| |i|| | 1 |
| Headlamp aim so that beam "kick up" is not visible on the screen both front lights |4.1.2 |a|| | 1 |
| Emissions not tested due to engine spluttering and cutting out on bet test |8.2.2.2 |e|| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis rail near spring |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases rear box joint (6.1.2 (a)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment hand brake travel high |1.1.6 |c|| | 1 |
| Offside Rear Anti-roll bar linkage damaged and seriously weakened Broken |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch under bonnett (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chasiss (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill front to rear (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill front to rear (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced corroded hole close to chassis leg (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg holed at subframe mounting area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg holed at subframe mounting area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage insecurely attached broken |5.3.3 |a| |i|| | 1 |
| Rear Exhaust emissions likely to be affected by an induction leak box (8.2.1.1 (b)) | 1 |
| Emissions not tested poor exhaust condition (8.2.1.2 (d)) | 1 |
| Inner Rear Road wheel bead rim badly distorted |4.2.A.1a| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded chassie |2.4.A.3| | 1 |
| Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
| Brake performance not tested due to leaking pipe (1.2.1 (g)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Nearside Front Inner Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings arch |6.1.B.2| | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering arch |6.1.1 |c| |ii|| | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion which adversely affects braking or steering arch |6.1.1 |c| |ii|| | 1 |
| Nearside Front Position lamp not working bulb blown (4.2.1 (a) (ii)) | 1 |
| Nearside Rear brake caliper leaking through parking brake mechanism |3.6.A.1| | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area is excessively corroded Floor |Outer fixing point| |5.2.6| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded Floor |Outer fixing point| |5.2.6| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 1 |
| Offside Body has a projection caused by corrosion inner floor pan/inner body sill |6.1.C.1| | 1 |
| Nearside Body has a projection caused by corrosion inner floor pan/inner body sill |6.1.C.1| | 1 |
| Emissions unable to be completed due to engine start to overheat. (8.2.1.2 (d)) | 1 |
| Front Upper Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Offside Front Floor excessively deteriorated corroded & holed |6.2.4 |a| |i|| | 1 |
| Nearside Front Inner Floor excessively deteriorated flitch corroded & holed |6.2.4 |a| |i|| | 1 |
| Central Rear Brake pipe at imminent risk of failure or fracture across rear axle as marked. (1.1.11 (a)) | 1 |
| Body component corroded and likely to cause injury o/s outer sill corroded at rear as marked. (6.2.1 (a) (i)) | 1 |
| Rear Anti-roll bar missing |2.4.G.1| | 1 |
| Nearside Front Lower Front suspension retaining device ineffective |2.5.A.4| | 1 |
| Offside Front Upper Front suspension locking device ineffective |2.5.A.4| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.065% (8.2.1.2 (c)) | 1 |
| Nearside Front Upper Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Front Upper Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg |5.3.6 |a| |i|| | 1 |
| Emissions unable to be completed aborted, not close to requirements (8.2.1.2 (d)) | 1 |
| Offside Rear Road wheel fixing loose locking bolt (5.2.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases joint to rear box |6.1.2 |a|| | 1 |
| Parking brake lever defective so that it cannot be satisfactorily operated (1.1.6 (d)) | 1 |
| Parking brake lever inoperative (1.1.6 (d)) | 1 |
| Central Front Exhaust emissions likely to be affected by an exhaust leak |8.2.1.1 |b|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill excess corrosion and body filler (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing underside of chassis rail next to anti roll bar mounting to chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm pin or bush excessively worn front and rear (5.3.4 (a) (i)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.28 la (8.2.1.2 (c)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill to inner backing sill chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing chassis arear (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn front and rear bushes (5.3.4 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits excess co 0.52 (8.2.1.2 (a)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor corroded (7.1.1 (a) (i)) | 1 |
| Nearside Rear Brake pipe leaking excessively corroded |3.6.A.1| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded arch corroded and holed |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded arch corroded and holed |5.2.6| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded sill corroded and holed |5.2.6| | 1 |
| Fluid leak harmful to the environment or a risk to other road users Power steering (8.4.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill and inner wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Rear Floor excessively deteriorated Boot floor (6.2.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/anti roll bar mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/antiroll bar mounting |5.3.6 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced floor/inner sill area |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension arm attachment bracket/mounting nut missing |2.4.G.1| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion outer sill |6.1.C.1| | 1 |
| Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected anti roll bar bracket area both sides |5.3.6 |a| |ii|| | 1 |
| Offside Front brake caliper has restricted free movement binding |3.5.1k| | 1 |
| Nearside Front brake caliper has restricted free movement binding |3.5.1k| | 1 |
| Exhaust emissions exceed manufacturers specified limit co exceeeds limits due to decat (8.2.2.2 (a)) | 1 |
| Central Rear Parking brake lever has no reserve travel Requires Adjusting |3.1.6b| | 1 |
| Offside Rear position lamp|s| not in a clean condition and function impaired |1.1.4a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Inner wheel arch |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 1 |
| Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Rear Exhaust silencer insecure |8.1.1 |b| |i|| | 1 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view sharp edge |3.3 |b| |ii|| | 1 |
| Offside Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting end of sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting end of sill (6.2.2 (d) (i)) | 1 |
| Offside Seat belt webbing significantly weakened (7.1.2 (b) (ii)) | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering BOTH SIDES, |6.1.1 |c| |ii|| | 1 |
| Nearside Rear Torsion bar insecure at an end fixing |2.4.E.2| | 1 |
| Offside Rear Lower Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded shockabsorber mounting |2.4.A.3| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded shockabsorber mounting |2.4.A.3| | 1 |
| Nearside Floor excessively deteriorated (6.2.4 (a) (i)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt link arm |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar linkage severely distorted |2.4.G.1| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis at front wheel bay |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill in various places (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch to strut (5.3.6 (a) (i)) | 1 |
| Nearside Lower Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings above upper suspension arm & anti roll bar mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings above upper suspension arm & anti roll bar mountings |6.1.B.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill area |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases at centre joint |7.1.2| | 1 |
| Central Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
| Central Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Offside Front Upper Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg/subframe mount (6.2.2 (d) (i)) | 1 |
| Nearside Front Outer Suspension component mounting prescribed area is excessively corroded chassis leg holed |2.4.A.3| | 1 |
| Offside Front Outer Suspension component mounting prescribed area is excessively corroded chassis leg holed |2.4.A.3| | 1 |
| Body has a sharp edge caused by corrosion NSR sill |6.1.C.1| | 1 |
| Offside Headlamps matched pair are incorrectly positioned |1.7.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Steering system excessively rough (2.1.1 (a)) | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Offside Anti-roll bar ball joint excessively worn both (5.3.4 (a) (i)) | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sills rusted (6.1.1 (c) (i)) | 1 |
| Front Anti-roll bar linkage ball joint excessively worn both (5.3.4 (a) (i)) | 1 |
| Brake performance not tested due to leaking brake pipe (1.2.1 (g)) | 1 |
| Nearside Rear Shock absorbers damaged to the extent that it does not function (5.3.2 (b)) | 1 |
| Nearside Rear Shock absorbers likely to become detached (5.3.2 (a) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill panel (7.1.1 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both side Anti-roll bar attachment bracket |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill panel (7.1.1 (a) (i)) | 1 |
| Nearside Floor excessively deteriorated holed (6.2.4 (a) (i)) | 1 |
| Offside Floor excessively deteriorated holed (6.2.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage insecure detatched |2.4.G.1| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded front and rear floor |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded front floor |5.2.6| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering by anti rollbar mount |6.1.A.1| | 1 |
| Exhaust silencer insecure Heat shield (8.1.1 (b) (i)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits CO 6.0 (8.2.1.2 (b)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill pannel (6.1.1 (c) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded cill area |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded cill area |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired chassis leg (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits 0.68% (8.2.1.2 (a)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits co reading to high (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.59% (8.2.1.2 (b)) | 1 |
| Central Exhaust has a major leak of exhaust gases silencer |6.1.2 |a|| | 1 |
| Front Headlamp not working on dipped beam both (4.1.1 (a) (ii)) | 1 |
| Emissions not tested no tail pipe (8.2.1.2 (d)) | 1 |
| Offside Front Body panel corroded and likely to cause injury wing (6.2.1 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits 1.04 (8.2.1.2 (c)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits 0.48% (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits 0.49% (8.2.1.2 (a)) | 1 |
| Central Exhaust has a major leak of exhaust gases and rear (6.1.2 (a)) | 1 |
| Emissions not tested due to condition of exhaust (8.2.1.2 (d)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch /chassis (5.3.6 (a) (i)) | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded on chassis leg |2.2.C.1h| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded on chassis leg |2.4.A.3| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded on chassis leg |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded sill area |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded on sill |2.4.A.3| | 1 |
| Nearside Rear Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded on sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength on chassis leg |5.3.6 |a| |i|| | 1 |
| Offside Front Anti-roll bar damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases bolt missing at rear flange (6.1.2 (a)) | 1 |
| Nearside Front Lower Anti-roll bar linkage missing |2.4.G.1| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is inadequately repaired Sill |5.3.6 |a| |i|| | 1 |
| Emissions not tested Vehicle over heating. |8.2.1.2 |d|| | 1 |
| Front Exhaust system not adequately supported downpipe bracket broken |7.1.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis anti roll bar mounting also within 30cm of strut top |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis anti roll bar mounting also within 30cm of strut top |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear sill to floor corroded (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed due to vehicle over heating (8.2.1.2 (d)) | 1 |
| Offside Front Side repeater insecure |1.4.A.2b| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassie (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Arch /jacking point (6.2.2 (d) (i)) | 1 |
| Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting Inner arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill panel - marked. (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill panel. (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill panel. (7.1.1 (a) (i)) | 1 |
| Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength N/s and o/s |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill inadequately repair (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill panel |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill closing panel |5.3.6 |a| |i|| | 1 |
| Power steering component leaking rack |2.1.5 |a|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced arch/sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced arch/sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Offside Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
| Offside Headlamp not working on dipped beam and main beam |4.1.1 |a| |ii|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced middle floor to sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced rear wing and sill |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced rear wing and sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Lower Suspension arm pin or bush excessively worn front & rear. (5.3.4 (a) (i)) | 1 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn front & rear. (5.3.4 (a) (i)) | 1 |
| Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Outer sill |5.2.6| | 1 |
| Offside Front Braking system leaking Brake caliper |3.6.A.1| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings side sill |6.1.B.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings side sill |6.1.B.2| | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill jacking point (6.2.2 (d) (i)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor near drivers seat mounting (6.1.1 (c) (i)) | 1 |
| Front Headlamp insecure |1.7.3| | 1 |
| Brake pipe leaking Front to Rear |3.6.A.1| | 1 |
| Headlamp not working on dipped beam both |1.7.5a| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inside arch |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings boot floor |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner chassis |6.1.B.2| | 1 |
| Service brake imbalanced across an axle (1.2.1 (b) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill. (7.1.1 (a) (i)) | 1 |
| Headlamp insecure |1.7.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded o/s and n/s outer sills. o/s and n/s front chassis sections |2.4.A.3| | 1 |
| Offside Brake cable insecure rear to brake caliper |3.5.1d| | 1 |
| Nearside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Upper Steering locking device missing ball joint split pin missing |2.1.3 |d|| | 1 |
| Steering rack insecure |2.2.B.1a| | 1 |
| Front Sub-frame damaged and seriously weakened |2.4.G.1| | 1 |
| Offside Rear Brake lever has restricted free movement |3.5.1k| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outtersill (7.1.1 (a) (i)) | 1 |
| Offside Front Road wheel fixing loose (5.2.1 (a) (i)) | 1 |
| Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Offside Front Direction indicator adversely affected by the operation of another lamp flashed headlamp with indicator |4.4.3 |b|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail in mounting areas |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch and outer sill in mounting areas |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill in mounting areas |5.3.6 |a| |i|| | 1 |
| Offside Front Steering locking device ineffective split pin missing (2.1.3 (d)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Rear Road wheel badly distorted (5.2.2 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sil (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint excessively worn lower ball joint (5.3.4 (a) (i)) | 1 |
| Offside Rear Sub-frame insecurely attached bolt broke (5.3.3 (a) (i)) | 1 |
| Nearside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt top (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt top (5.3.4 (b) (ii)) | 1 |
| Nearside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt lower (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt lower (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases silencer (6.1.2 (a)) | 1 |
| Front Fuel hose leaking |7.2.3| | 1 |
| Offside Body component damaged and likely to cause injury mirror cover (6.2.1 (a) (i)) | 1 |
| Headlamp light source and lamp not compatible Both (4.1.4 (c)) | 1 |
| Offside Front Seat belt damaged sufficient to significantly weakened the webbing drivers |5.2.2a| | 1 |
| Offside Steering locking device missing track rod end castle nut split pin |2.2.C.1g| | 1 |
| Nearside Steering locking device missing track rod end castle nut split pin |2.2.C.1g| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Headlamp insecure brackets broken |1.7.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis hold |2.4.A.3| | 1 |
| Nearside Rear coil spring broken broken at top |2.4.C.1a| | 1 |
| Exhaust has a major leak of exhaust gases rear box hold and blowing |7.1.2| | 1 |
| Steering locking device missing both track rod ends lock nuts split pins missing |2.2.C.1g| | 1 |
| Nearside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chasis rail |5.3.6 |a| |ii|| | 1 |
| Offside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chasis rail |5.3.6 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheelarch (5.3.6 (a) (i)) | 1 |
| Oil leaking excessively from transmission rear diff |8.4.1 |a| |i|| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint anti roll bar link |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint anti roll bar link |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint anti roll bar link |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint anti roll bar link |2.4.G.2| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Offside rear inner sill (7.1.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage attachment bracket/mounting fractured Mounting bolt corroded and fallen off |5.3.3 |b| |ii|| | 1 |
| Rear Exhaust has a major leak of exhaust gases flange (6.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis |5.3.6 |a| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases centre to rear flange |7.1.2| | 1 |
| Rear brake caliper leaking |3.6.A.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill panel |7.1.1 |a| |i|| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill panel |7.1.1 |a| |i|| | 1 |
| Power steering pipe/hose corroded such that the steering is adversely affected |2.1.5 |g| |ii|| | 1 |
| Nearside Front Tie bar/rod rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Emissions not tested Vehicle overheating (8.2.1.2 (d)) | 1 |
| Offside Front Body panel insecure Wing (6.2.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases box blowing (6.1.2 (a)) | 1 |
| Nearside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement both rear and hub bush. |2.4.G.2| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill by |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill by |5.2.6| | 1 |
| Nearside Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor to sill nearside and offside |6.1.B.2| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 1 |
| Nearside Front Road wheel badly distorted (5.2.2 (c) (i)) | 1 |
| Fuel system component leaking Fuel filter |7.2.3| | 1 |
| Front Position lamp not working both side lights (4.2.1 (a) (ii)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill x2 |5.2.6| | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor holed (6.2.2 (d) (i)) | 1 |
| Front passenger seat insecure |6.2.3| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill holed |7.1.1 |a| |i|| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Floor excessively deteriorated seat mounting |6.2.4 |a| |i|| | 1 |
| Rear Exhaust has a major leak of exhaust gases PIPE JOINTS |7.1.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases flange joint corroded (6.1.2 (a)) | 1 |
| Nearside Front Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area is inadequately repaired floor area plates not welded fully (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is inadequately repaired outer sill not welded fully (7.1.1 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis holed (5.3.6 (a) (i)) | 1 |
| Offside Headlamp light intensity severely reduced headlamp faded (4.1.4 (a)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner and otter sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outter sill (7.1.1 (a) (i)) | 1 |
| Offside Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting at floor pan onto inner sill (6.2.2 (d) (i)) | 1 |
| Offside Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
| Nearside Rear Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering in arch by suspension leg chalked |6.1.1 |c| |ii|| | 1 |
| Offside Stop lamp not working renew bulb |1.2.1b| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill in 2 places |7.1.1 |a| |i|| | 1 |
| Offside Front Lower Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Rear Lower Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassi in front off wheel (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassi rail underside (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength back panel (5.3.6 (a) (i)) | 1 |
| Offside Outer Front Anti-roll bar fractured |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis x2 |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis x2 |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both sides, outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front position lamp|s| not working And offside front |1.1.A.3b| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front chassis /flitch (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area is inadequately repaired both sills (5.3.6 (a) (i)) | 1 |
| Central Front Shock absorbers has a serious fluid leak (5.3.2 (b)) | 1 |
| Emissions not tested engine running rich (8.2.1.2 (d)) | 1 |
| Central Exhaust has a major leak of exhaust gases Center middle box corroded/cracked (6.1.2 (a)) | 1 |
| Offside Front Upper Suspension rod ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Headlamp aim unable to be tested and offside not working (4.1.2 (b)) | 1 |
| Nearside Headlamp not working on dipped beam and offside (4.1.1 (a) (ii)) | 1 |
| Emissions unable to be completed cat missing (8.2.1.2 (d)) | 1 |
| Nearside Steering component mounting prescribed area is inadequately repaired |2.2.C.1h| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded floor area |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis to inner wing area |2.4.A.3| | 1 |
| Nearside Front brake caliper inappropriately repaired |3.5.1n| | 1 |
| Offside Front brake caliper inappropriately repaired |3.5.1n| | 1 |
| Emissions not tested battery light illuminated during test |8.2.1.2 |d|| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch area |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch area |6.1.B.2| | 1 |
| Nearside Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis leg |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail on floor |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis rail on floor |6.1.B.2| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded inner wheel arch at top strut mounting |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded inner wheel arch at top strut mounting |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch and outer sill |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases mid to rear section |7.1.2| | 1 |
| Rear Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Front Anti-roll bar missing |2.4.G.1| | 1 |
| Front suspension has a suspension upper ball joint securing nut not locked |2.5.B.1a| | 1 |
| Front suspension has a suspension lower ball joint securing nut not locked |2.5.B.1a| | 1 |
| Offside Rear Coil spring fractured or broken (top coil) (5.3.1 (b) (i)) | 1 |
| Wheel nut|s| missing both rear |4.2.A.1e| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner bay |6.1.1 |c| |i|| | 1 |
| Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced both sills (7.1.1 (a) (i)) | 1 |
| Rear position lamp|s| missing |1.1.A.3a| | 1 |
| Stop lamp missing |1.2.1a| | 1 |
| Rear Direction indicator missing |1.4.A.2b| | 1 |
| Rear reflector missing |1.5.1a| | 1 |
| Exhaust emissions exceed manufacturers specified limit CO too high (8.2.2.2 (a)) | 1 |
| Emissions unable to be completed Exhaust snapped at middle box (8.2.1.2 (d)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill rotten with 30cm of seat belt anchor (7.1.1 (a) (i)) | 1 |
| Offside Rear Upper Coil spring not correctly located |2.4.C.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 1 |
| Nearside Front Body panel corroded and likely to cause injury wing (6.2.1 (a) (i)) | 1 |
| Nearside Rear Lower Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired chassis leg holed [under seat] (6.2.2 (d) (ii)) | 1 |
| Nearside Front Lower Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired inner sill area , (6.2.2 (d) (ii)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired inner sill , (6.2.2 (d) (ii)) | 1 |
| Offside Rear Lower Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill area ,[weak and corroded] (6.2.2 (d) (ii)) | 1 |
| Nearside Front Upper Integral body structure has excessive corrosion which adversely affects braking or steering inner wing area . (6.1.1 (c) (ii)) | 1 |
| Front Exhaust has a major leak of exhaust gases flange leak . (6.1.2 (a)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg badly corroded and holed , (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg badly holed , (5.3.6 (a) (i)) | 1 |
| Nearside Front Coil spring mounting corroded and seriously weakened (5.3.1 (b) (i)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system burst during brake roller test, corroded next to clip at o/s rear floor |I temporarily crimped pipe infront of clip to stem fluid flow and protect rest of system from draining dry| |1.1.11 |b| |ii|| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive c0 0.527% |7.3.D.4| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive co 0.746% |7.3.D.3| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits co0.478% |8.2.1.2 |a|| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits Lambda 1.187 |8.2.1.2 |c|| | 1 |
| Nearside rear brake recording little or no effort zero effort |3.7.B.5a| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive co 0.4726 |7.3.D.3| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nearside front floor |5.2.6| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive co 0.385 |7.3.D.4| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive co 0.675 |7.3.D.3| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits lambda 1.078 |7.3.D.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill at rear |5.2.6| | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt upper suspension arm (5.3.4 (b) (ii)) | 1 |
| Offside Position lamp showing red light to the front |4.2.3 |a| |ii|| | 1 |
| Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Exhaust has a major leak of exhaust gases x2 (6.1.2 (a)) | 1 |
| Offside Rear Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting worn and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded Inner sill |2.4.A.3| | 1 |
| Offside Rear Inner Brake hose connection leaking on a hydraulic braking system |1.1.12 |c| |ii|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis by anti roll bar (d) bush (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area excessively corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis near top arm mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Headlamp aim beam image obviously incorrect n/s o/s weak image |1.8.A.1b| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded floor to inner sill |5.2.6| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner chassis rail (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis leg (5.3.6 (a) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing area (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill x2 (7.1.1 (a) (i)) | 1 |
| Front Position lamp not working both |4.2.1 |a| |ii|| | 1 |
| Rear Position lamp not working both |4.2.1 |a| |ii|| | 1 |
| Rear Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Road wheel fixing missing all 4 wheel one nut missing |5.2.1 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded back of sill |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis as marked |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis as marked |2.4.A.3| | 1 |
| Nearside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt Boot |2.2.C.1c| | 1 |
| Parking brake inoperative on one side very low (1.4.1 (a)) | 1 |
| Power steering pipe|s| or hose|s| excessively corroded leaking |2.3.2| | 1 |
| Central Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced MARKED (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting MARKED (6.2.2 (d) (i)) | 1 |
| Offside Front Front position lamp|s| not working head light |1.1.A.3b| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength n/s outer sill at rear |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner end of sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Front Subframe mounting prescribed area is excessively corroded Chassis at front of front subframe, both sides |2.4.A.3| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 1 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded Sill panel |5.2.6| | 1 |
| Nearside Front Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected shocker mount (5.3.6 (a) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Ball joint has excessive play |2.2.B.1f| | 1 |
| Electronic braking system warning device inoperative (1.7 (a)) | 1 |
| Emissions not tested exhaust leak (8.2.2.2 (e)) | 1 |
| Nearside Front Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded front to rear floor pans |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded front to rear floor pans |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded front to rear chassis rail |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| coil spring broken n/s/r |2.4.C.1a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Exhaust silencer likely to become detached clamps missing (8.1.1 (b) (ii)) | 1 |
| Offside Front Suspension arm pin or bush likely to become detached front bolt (5.3.4 (a) (ii)) | 1 |
| Front Subframe mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected bolt to wish bone front (5.3.6 (a) (ii)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak whole exhaust (8.2.2.1 (b)) | 1 |
| Offside Anti-roll bar linkage pin or bush excessively worn nut loose (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm pin or bush excessively worn bush front (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected corner/inner sill (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected corner/inner sill (5.3.6 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced corner/inner sill (7.1.1 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Box (6.1.2 (a)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill panel |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill panel |2.4.A.3| | 1 |
| Offside Rear Brake cable locking device insecure |3.5.1l| | 1 |
| Offside Seat belt not functioning as intended |7.1.2 |c|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength UNDER SILL PANEL CORRODED (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg, anti roll bar D bush mount area (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg, anti roll bar D bush mount area (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg, inner wheel arch, D bush area in TWO PLACES (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill / seat belt mount (6.1.1 (c) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak centre to rear box on exhaust joint (8.2.1.1 (b)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch / chassis leg (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis corroded near suspension mountings. |5.3.6 |a| |i|| | 1 |
| Offside Front Brake hose excessively stretched hose stretched on full left hand lock due to wheel spacers fitted. |1.1.12 |b| |ii|| | 1 |
| Nearside Front Brake hose excessively stretched hose stretched on full right hand lock due to wheel spacers fitted. |1.1.12 |b| |ii|| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
| Offside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded multiple areas |5.2.6| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded floor pan. |5.2.6| | 1 |
| Offside Front Seat belt anchorage likely to become detached in the event of a collision |7.1.1 |a| |ii|| | 1 |
| Emissions unable to be completed Due to car stalling (8.2.1.2 (d)) | 1 |
| Rear Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Rear fog lamp switch missing |4.5.3 |a| |ii|| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER SILL |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings INNER SILL |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings O/S INNER SILL / FLOOR HOLED THROUGH CORROSION |6.1.B.2| | 1 |
| Emissions not tested tick over to high engine over heating (8.2.1.2 (d)) | 1 |
| Offside Front Steering linkage ball joint ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Front Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Offside Front Headlamp light source and lamp not compatible LED HID (4.1.4 (c)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected reverse light (4.5.1 (b) (ii)) | 1 |
| Emissions unable to be completed coolant loss and smoke (8.2.1.2 (d)) | 1 |
| Upper Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Offside Front Anti-roll bar locating pin locking device not properly locked |2.4.G.3b| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Upper Seat belt anchorage prescribed area is excessively corroded inner wheel arch |5.2.6| | 1 |
| Brake master cylinder defective but brake still operating Brake pedal sinks to floor after prolonged application. (1.1.10 (b) (i)) | 1 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced bad earth |1.7.5a| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded chassis |2.2.C.1h| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded anti roll bar |2.4.A.3| | 1 |
| Exhaust emissions likely to be affected by an induction leak (8.2.1.1 (b)) | 1 |
| Offside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced SILL |7.1.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTSIDE EDGE OF CHASSIS |5.3.6 |a| |i|| | 1 |
| Nearside Front Upper Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |