| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 17 |
| Horn not working (7.7 (a)) | 10 |
| Registration plate lamp issues | 10 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 8 |
| Headlamp aim out of alignment | 7 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 6 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 6 |
| Brake pipe excessively corroded | 6 |
| Nearside Stop lamp not working |1.2.1b| | 5 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 5 |
| Registration plate issues | 5 |
| Anti-lock braking system warning lamp indicates an ABS fault | 5 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 5 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Windscreen washer not working | 4 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 3 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Rear fog lamp not working |1.3.2b| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Fuel system component leaking (6.1.3 (b) (i)) | 3 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 2 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
| Offside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member (6.1.1 (c) (i)) | 2 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 2 |
| Emissions unable to be completed (8.2.2.2 (e)) | 2 |
| Nearside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 2 |
| Nearside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Rear parking brake recording little or no effort | 2 |
| Brakes imbalanced across an axle | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill and inner arch (5.3.6 (a) (i)) | 2 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Windscreen has damage | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Rear Seat belt attachment fitting fractured |5.2.3| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Cross member corroded (6.1.1 (c) (i)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Cross member/ tow bar mounting (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect LENS GLAZED (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect LENS GLAZED (4.1.2 (c)) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
| Oil leaking excessively from engine engine and intercooler (8.4.1 (a) (i)) | 1 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Position lamp not working All (4.2.1 (a) (ii)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced both rear inner wheel arches (7.1.1 (a) (i)) | 1 |
| Nearside Rear Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt not functioning as intended catch missing (7.1.2 (c)) | 1 |
| Offside Rear Seat belt not functioning as intended catch missing (7.1.2 (c)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength x member (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing by antiroll bar mounting x member (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is inadequately repaired sill / floor (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Rear Inner Anti-roll bar pin or bush excessively worn both (5.3.4 (a) (i)) | 1 |
| Offside Front Headlamp lens seriously defective deteriorated (4.1.1 (b) (ii)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values retested and passed (8.2.2.2 (f)) | 1 |
| Power steering component leaking Steering rack (2.1.5 (a)) | 1 |
| Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting cross member (6.2.2 (d) (i)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wishbone mount holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember holed by sub frame mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength crossmember holed (5.3.6 (a) (i)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Silencer (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut top area (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sills in prscribed area (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill in prescribed area (7.1.1 (a) (i)) | 1 |
| Rear Towbar component excessively corroded tow bar attachment cross member (6.1.6 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Headlamp has a product on the light source so that the light output is severely reduced offside and nearside lenses polished during test (4.1.4 (b)) | 1 |
| Offside Front Service brake excessively binding Brake Disc Showing Evidence of Overheating (1.2.1 (f)) | 1 |
| Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt offside and nearside (5.3.4 (b) (ii)) | 1 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Suspension component corroded and seriously weakened Outer sill (5.3.3 (b) (i)) | 1 |
| Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILLS, INNER WHEEL ARCHES (6.2.2 (d) (i)) | 1 |
| Rear Anti-roll bar linkage pin or bush excessively worn BOTH (5.3.4 (a) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn both sides (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is inadequately repaired arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch two areas (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch two areas (5.3.6 (a) (i)) | 1 |
| Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Offside Front Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting fractured SNAPPED (5.3.3 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength FRONT OF INNER WHEEL ARCH & ALSO REAR OF INNER ARCH (5.3.6 (a) (i)) | 1 |
| Offside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting bumper support (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Nearside Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Offside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength under battery (5.3.6 (a) (i)) | 1 |
| Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch (6.2.2 (d) (i)) | 1 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Front Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Rear Seat belt missing centre lap belt (7.1.2 (a)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Outer Integral body structure is fractured and structural rigidity is significantly reduced sill (6.1.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure is fractured and structural rigidity is significantly reduced crossmember (6.1.1 (a) (i)) | 1 |
| Offside Rear Integral body structure is fractured and structural rigidity is significantly reduced crossmember (6.1.1 (a) (i)) | 1 |
| Offside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Outer Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch/floor (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill backing (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front of inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting damaged and seriously weakened Bush missing (5.3.3 (b) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front of inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear of inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength central mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Within 30cm of strut top mounting. (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear inner sill. (5.3.6 (a) (i)) | 1 |
| Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Central Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill panel excessively corroded on inner (6.1.1 (c) (i)) | 1 |
| Offside Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Exhaust has a major leak of exhaust gases rear box |7.1.2| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill and inner arch |2.4.A.3| | 1 |
| Nearside Inner Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded outer sill and inner arch |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded chassis holed within 30 cm of upper shock mounting point |2.4.A.3| | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting cracked |2.4.G.1| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Front brake excessively fluctuating | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill front to back |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill front to back |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings out rigger |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis in wheel arch |6.1.B.2| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` dangler on mirror |8.3.1e| | 1 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Nearside Front Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings outrigger |6.1.B.2| | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill section (6.2.2 (d) (i)) | 1 |
| Offside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crash bar (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 1 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Offside Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Passengers seat insecure rear row (6.2.6 (a) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced center of outer sill and inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced center of inner sill (6.1.1 (c) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases box (6.1.2 (a)) | 1 |
| Nearside Rear Lower Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced around towing eye (6.1.1 (c) (i)) | 1 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
| Rear Brake disc significantly and obviously worn both (1.1.14 (a) (i)) | 1 |
| Nearside Rear Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced around back exhaust mounts (6.1.1 (c) (i)) | 1 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Front Brake disc significantly and obviously worn both (1.1.14 (a) (i)) | 1 |
| Central Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both sides (6.1.1 (c) (i)) | 1 |
| Emissions not tested (8.2.2.2 (e)) | 1 |
| Nearside Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Side repeater lens defective such that the emitted light is adversely affected (4.4.1 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Brake disc contaminated (1.1.14 (b)) | 1 |
| Nearside Rear Braking system leaking |3.6.A.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch to inner sill |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis member |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis member |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced quarter panel |7.1.1 |a| |i|| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch under car |7.1.1 |a| |i|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch under car |7.1.1 |a| |i|| | 1 |
| Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction |3.1 |a| |ii|| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced crossmember |7.1.1 |a| |i|| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Rear brake drum contaminated by oil |3.5.1h| | 1 |
| Battery insecure |1.9.1| | 1 |
| Exhaust has a major leak of exhaust gases at centre |7.1.2| | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear brake disc contaminated by oil inner face |3.5.1h| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill / outrigger (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill / outrigger (5.3.6 (a) (i)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill Corroded (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Subframe and suspension mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Subframe and suspension mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Rear Vehicle structure is so weakened by corrosion within 30cm of a towbar mounting, the towbar is likely to become detached chassis (6.1.6 (i) (ii)) | 1 |
| Offside Rear Vehicle structure is so weakened by corrosion within 30cm of a towbar mounting, the towbar is likely to become detached chassis leg (6.1.6 (i) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired subframe mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor (7.1.1 (a) (i)) | 1 |
| Offside Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Brake hose excessively deteriorated | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Nearside Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre section (6.1.2 (a)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point (6.2.2 (d) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/jacking point (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill and inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill and inner arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill and inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Drivers seat insecure bolts loose in floor (6.2.5 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Brake lever has abnormal movement of levers indicating excessive wear or maladjustment (1.1.15 (f)) | 1 |
| Drivers airbag missing steering wheel (7.1.5 (a)) | 1 |
| Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced front and rear sills holed x3 (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill holed about 3/4 of sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis holed (5.3.6 (a) (ii)) | 1 |
| Road wheel fixing missing all four wheels has one bolt missing (5.2.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill to wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear fog lamp missing |1.3.2a| | 1 |
| Front brake application uneven | 1 |
| front brakes release unevenly |3.7.B.4| | 1 |
| Nearside Headlamp lens seriously defective deteriated (4.1.1 (b) (ii)) | 1 |
| Offside Headlamp lens seriously defective deteriated (4.1.1 (b) (ii)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch area (6.1.1 (c) (i)) | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis support beam (6.1.1 (c) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill holed (7.1.1 (a) (i)) | 1 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Nearside Headlamp aim beam image obviously incorrect lense |1.8.A.1b| | 1 |
| Offside Headlamp aim beam image obviously incorrect lense |1.8.A.1b| | 1 |
| Indicator switch faulty no selecting near side |1.4.A.1| | 1 |
| Nearside Rear passenger door cannot be opened from outside the vehicle |6.2.B.1c| | 1 |
| Nearside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement d bush |2.4.G.2| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill to flitch (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill to flitch (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Oil leaking continuously from transmission posing a serious risk to road safety (8.4.1 (a) (ii)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users water (8.4.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 1 |
| Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Cross member (6.1.1 (c) (i)) | 1 |
| Front Headlamp lens seriously defective both front light lens do not have a beam image (4.1.1 (b) (ii)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Oil leaking excessively from transmission transmission pipes next to gearbox corroded and leaking (8.4.1 (a) (i)) | 1 |
| Battery insecure and likely to cause a short circuit leisure battery (4.13 (a) (ii)) | 1 |
| Offside Rear Body panel insecure inner wheel arch, fuel pipe cover (6.2.1 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Suspension arm ball joint excessively worn both front lower joints (5.3.4 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill holed+corroded (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill holed+corroded x2 (6.2.2 (d) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis as marked (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out-rigger/under step (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill back (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under arch/inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under arch/inner wing (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Offside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill corroded and holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill corroded and holed (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front Lower Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sil (6.2.2 (d) (ii)) | 1 |