| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 60 |
| Parking brake: efficiency below requirements |3.7.B.7| | 47 |
| Registration plate lamp issues | 41 |
| Rear parking brake recording little or no effort | 40 |
| Headlamp aim out of alignment | 37 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 15 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 14 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 12 |
| Parking brake lever has no reserve travel |3.1.6b| | 12 |
| Brakes imbalanced across an axle | 10 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 8 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 7 |
| Registration plate issues | 7 |
| Windscreen washer not working | 7 |
| Rear brake disc in such a condition that it is seriously weakened | 6 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 6 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 5 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 5 |
| Offside Rear passenger door cannot be opened from outside the vehicle |6.2.B.1c| | 5 |
| Offside Rear fog lamp not working |1.3.2b| | 5 |
| Windscreen has damage | 5 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 5 |
| Brake pipe excessively corroded | 5 |
| Front brake disc in such a condition that it is seriously weakened | 4 |
| Nearside Rear Stop lamp not working |1.2.1b| | 4 |
| Electronic stability system warning lamp indicates a fault |3.4.1c| | 4 |
| Offside Front Position lamp not working |4.2.1 |a|| | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Rear fog lamp not working |1.3.2b| | 4 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 4 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Horn not working (7.7 (a)) | 4 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 3 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Offside Front Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 3 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside rear parking |secondary| brake grabbing severely |3.7.B.6b| | 3 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 3 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 3 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 3 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 3 |
| Offside front brake binding |3.7.B.1| | 3 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 3 |
| Nearside Stop lamp not working |1.2.1b| | 3 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 3 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Emissions unable to be completed (8.2.2.2 (e)) | 3 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Fuel system component leaking (6.1.3 (b) (i)) | 3 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 3 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 3 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 2 |
| Nearside Front Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 2 |
| Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 2 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 2 |
| Rear brake application uneven | 2 |
| Offside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Front Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 2 |
| Front position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 2 |
| Offside Rear Stop lamp not working |1.2.1b| | 2 |
| Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 2 |
| Offside Front brake disc excessively pitted |3.5.1h| | 2 |
| front brake binding |3.7.B.1| | 2 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Side repeater not working |1.4.A.2c| | 2 |
| Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL (5.3.6 (a) (i)) | 2 |
| Nearside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 2 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 2 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 2 |
| Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 2 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Front Obligatory mirror insecure |8.1.1| | 2 |
| Front brake excessively fluctuating | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Brake disc contaminated (1.1.14 (b)) | 2 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 2 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 2 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded OUTER SILL |2.4.A.3| | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Nearside Parking |secondary brake| on a single line braking system grabbing severely |1.3.1 |c|| | 1 |
| Offside Parking |secondary brake| on a single line braking system grabbing severely |1.3.1 |c|| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Nearside Front All position lamps not working |1.1.A.3b| | 1 |
| Nearside Front Anti-roll bar linkage severely distorted |2.4.G.1| | 1 |
| Offside Rear Wheel nut|s| missing |4.2.A.1e| | 1 |
| Offside Rear Brake hose twisted |3.6.B.4c| | 1 |
| Nearside Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| rear parking |secondary| brakes imbalanced | 1 |
| Front suspension retaining device missing |2.5.A.4| | 1 |
| Offside Front Lower Suspension arm insecure |2.4.G.1| | 1 |
| Brake operation has insufficient reserve pressure/vacuum to provide assistance for at least two more brake applications after the warning lamp or other device has operated |3.3.E.5b| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Engine MIL inoperative or indicates a malfunction |8.2.2.2 |g|| | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 1 |
| Offside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Nearside Suspension arm ball joint dust cover missing |2.4.G.2| | 1 |
| Offside Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 1 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
| Nearside Rear Statutory seat belt missing |5.1.1| | 1 |
| Offside Rear Statutory seat belt missing |5.1.1| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Central Front Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
| Offside passenger door cannot be opened from outside the vehicle |6.2.B.1c| | 1 |
| Offside Rear Parking |secondary brake| on a single line braking system grabbing severely |1.3.1 |c|| | 1 |
| Front Anti-roll bar linkage ball joint excessively worn both bottom ball joint |5.3.4 |a| |i|| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed and corroded |6.1.1 |c| |i|| | 1 |
| Offside Front Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer cill |2.4.A.3| | 1 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine 3.61 |7.4.B.3b| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1 |
| Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Emissions not tested |7.3.A.1| | 1 |
| Nearside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Front Subframe mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Service brake: efficiency below requirements |3.7.D.4| | 1 |
| Nearside Rear brake disc excessively pitted |3.5.1h| | 1 |
| Offside Rear brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Rear front brake binding |3.7.B.1| | 1 |
| Offside Outer Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Emissions not tested |7.0| | 1 |
| Offside Front Trailing arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Steering locking device missing |2.2.C.1g| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Outer Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Outer Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside rear brake grabbing severely |3.7.A.5b| | 1 |
| Offside Rear Outer Subframe mounting prescribed area is excessively corroded [sill panel] |2.4.A.3| | 1 |
| Electronic stability system switch faulty |3.4.5| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill/inner wheel arch |2.4.A.3| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front panel (5.3.6 (a) (i)) | 1 |
| Nearside rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside front brake juddering severely |3.7.A.2b| | 1 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings auter sill |6.1.B.2| | 1 |
| rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill area |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded centre sill area |5.2.6| | 1 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Side repeater missing (4.4.1 (a) (ii)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Seat belt buckle missing seat missing (7.1.2 (d)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure inadequately repaired such that structural rigidity is significantly reduced patch come away from body (6.1.1 (d) (i)) | 1 |
| Central Fuel system component leaking (6.1.3 (b) (i)) | 1 |
| Nearside Front Lower Integral body structure inadequately repaired such that structural rigidity is significantly reduced (6.1.1 (d) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced lower inner wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced CENTRE INNER SILL (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL (5.3.6 (a) (i)) | 1 |
| Oil leaking excessively from transmission oil cooler front (8.4.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Oil leaking excessively from transmission diff seal leaking on brake disc (8.4.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Headlamp aim projected beam image is obviously incorrect both fronts (4.1.2 (c)) | 1 |
| Nearside Rear Position lamp lens seriously defective (4.2.1 (b)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front cross member rusty and holed o/s n/s (6.1.1 (c) (i)) | 1 |
| Offside Floor excessively deteriorated inner sill panel rusty (6.2.4 (a) (i)) | 1 |
| Rear fog lamp insecure |1.3.2a| | 1 |
| Rear Electrical wiring insecure |1.9.2a| | 1 |
| Rear Trailer electrical socket damaged so that lead cannot be securely connected |1.9.3b| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Centre Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Inner Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded under wheel arch |5.2.6| | 1 |
| Nearside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Front suspension has excessive movement at a wishbone pin or bush rear |2.5.A.1c| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Rear Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Suspension arm attachment bracket/mounting insecure and impairing directional stability |5.3.3 |a| |ii|| | 1 |
| Offside Front Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Power steering pipe/hose leaking |2.1.5 |a|| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Rear Towbar excessively corroded within 30cm of towbar mounting |6.1.6 |i| |i|| | 1 |
| Offside Rear Towbar excessively corroded within 30cm of towbar mounting |6.1.6 |i| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to sill |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength step |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/step |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Headlamp aim not tested (4.1.2 (b)) | 1 |
| Offside Rear Road wheel fixing missing wheel nut and stud (5.2.1 (a) (i)) | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer + Inner sill. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill. (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill. (6.1.1 (c) (i)) | 1 |
| Offside Rear Other passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Rear Passengers seat backrest cannot be secured in the upright position. (6.2.6 (a) (i)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill area (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting front crossmember (6.2.2 (d) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Front Headlamp incorrect colour both (4.1.4 (a)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner wheel arch (multiple areas) (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Hole in chassis (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced hole in sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Axle swivel pins and bushes swivel pin and/or bush excessively worn Wish bone back bush (5.1.2 (b) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases flex section badly split/deteriorated (6.1.2 (a)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Brake servo defective or ineffective (1.1.10 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength step (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength step (5.3.6 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front to rear outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front to rear inner sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front to rear outer sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front to rear inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front to rear chassis corroded (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front to rear chassis corroded (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Drive shaft joint excessively worn (6.1.7 (c) (i)) | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Rear Exhaust system insecure do not think its the rite exhaust!!! (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength all of the inner sill. (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill to floor (5.3.6 (a) (i)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Offside Rear Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe/ radiator mount area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength trailing arm mount (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill several holes (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill 2 holes (5.3.6 (a) (i)) | 1 |
| Offside Entrance/exit step significantly damaged insecure (9.7 (a) (ii)) | 1 |
| Offside Front Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill x2 (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill x2 (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced above exhaust (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting back up sill (6.2.2 (d) (i)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill marked with chalk (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill marked with chalk (6.1.1 (c) (i)) | 1 |
| Position lamp not working all not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Rear Anti-roll bar linkage attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Steering component mounting prescribed area is excessively corroded Outer Sill (2.1.2 (e) (i)) | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Nearside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Nearside Rear Stop lamp(s) lens defective such that the emitted light is adversely affected (4.3.1 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Front Valve stem seriously damaged both (5.2.3 (j)) | 1 |
| Nearside Rear Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and outer sill (5.3.6 (a) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn d bushs (5.3.4 (a) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill corroded marked yellow (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill corroded marked yellow (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill to inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn Mounting D bush. (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn Mounting D bush. (5.3.4 (a) (i)) | 1 |
| Headlamp not working on main beam both (4.1.1 (a) (ii)) | 1 |
| Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 1 |
| Fuel system component leaking fuel pump (6.1.3 (b) (i)) | 1 |
| Central Exhaust system insecure (6.1.2 (a)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Vehicle structure fractured seriously affecting its strength within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Offside Vehicle structure fractured seriously affecting its strength within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength tie bar mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength tie bar mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Position lamp not working o/s/f (4.2.1 (a) (ii)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced fronts (4.1.4 (b)) | 1 |
| Rear fog lamp not working rear (4.5.1 (a) (ii)) | 1 |
| Battery insecure and likely to fall from carrier o/s/f (4.13 (a) (ii)) | 1 |
| Steering rack gaiter missing or no longer prevents the ingress of dirt o/s/f n/s/f (2.1.3 (g) (ii)) | 1 |
| Anti-roll bar linkage pin or bush likely to become detached o/s/f link off / hitting wheel (5.3.4 (a) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s/f inner wing area (5.3.6 (a) (i)) | 1 |
| Vehicle structure is fractured and so weakened within 30cm of a towbar mounting, the towbar is likely to become detached o/s/r (6.1.6 (i) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength n/s/f (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s/f (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength n/s/r (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s/r (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area is inadequately repaired both rear sill areas (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s/r n/s/r inner arches (5.3.6 (a) (i)) | 1 |
| Brake pipe at imminent risk of failure or fracture n/s/f brake pip burst (1.1.11 (a)) | 1 |
| Brake performance not tested due to burst pipe (1.2.1 (g)) | 1 |
| Emissions not tested due to aborted test (8.2.2.2 (e)) | 1 |
| Anti-roll bar missing remains of linkage/torn brackets (5.3.3 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/arch front & rear of axle holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut turret (5.3.6 (a) (i)) | 1 |
| Brake lever has abnormal movement of levers indicating excessive wear or maladjustment (1.1.15 (f)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired inner sill patches not continuously welded & body filler sills (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired sill/inner sill not continuously welded/body filler (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section/outrigger near suspension arm (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/outrigger near suspension arm (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired box section near subframe not continuously welded/body filler (5.3.6 (a) (i)) | 1 |
| Steering rack gaiter missing or no longer prevents the ingress of dirt both boots split (2.1.3 (g) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced underside of step/base of B post (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced underside of step/base of B post (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/outrigger near subframe behind axle (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch holed x 2 (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch holed (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Nearside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Anti-roll bar missing (5.3.3 (a) (ii)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 1 |
| Offside Service brake is causing the steering wheel to severely pull one way (1.2.1 (b) (i)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Offside Rear Lower Rear fog lamp does not emit a steady red light Clear lens / red bulb weak. (4.5.4 (a)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect Glass lens unit. Inside lens discoloured. (4.1.2 (c)) | 1 |
| Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt Split. (5.3.4 (b) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn Steel bar drop link. (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn Steel bar drop link. (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Service brake excessively binding Restricted movement. (1.2.1 (f)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill heavily corroded / holes. (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Seat belt buckle not functioning as intended rear seat 6/7 buckle wont lock (7.1.2 (d)) | 1 |
| Nearside Front Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Offside Rear Passengers seat insecure rear seat 6/7 wont lock in down position (6.2.6 (a) (ii)) | 1 |
| Offside Rear Inner Vehicle structure excessively corroded within 30cm of towbar mounting panel (6.1.6 (i) (i)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Rear Other passenger door cannot be opened from outside the vehicle tail gate (6.2.3 (a)) | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Other passenger door cannot be opened from outside the vehicle |6.2.3 |a|| | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Central Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Offside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Front Anti-roll bar insecure drop link |2.4.G.1| | 1 |
| Offside Front Anti-roll bar linkage missing |2.4.G.1| | 1 |
| Offside Front Windscreen wiper not working (3.4 (a)) | 1 |
| Nearside Front Windscreen wiper not working (3.4 (a)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Body component likely to become detached radiator (6.2.1 (a) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Cross member corroded and holed (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner lower wheel arch area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch area (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt buckle missing middle row (7.1.2 (d)) | 1 |
| Central Rear Seat belt buckle missing middle row (7.1.2 (d)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Front Cross-member (6.2.2 (d) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired wheel tub has corroded and become detached, marked with chalk (6.2.2 (d) (ii)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Front Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting marked with chalk (6.1.6 (i) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail has hole corroded at front where vehicle tow loop is connected
marked in chalk (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced previous repair inside wheel tub on chassis rail has corroded behind underseal , marked with chalk (6.1.1 (c) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn both rear bushes excess worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected Inner sill (5.3.6 (a) (ii)) | 1 |
| Offside Steering component mounting prescribed area so damaged that control of the vehicle is likely to be adversely affected Steering moount (2.1.2 (e) (ii)) | 1 |
| Steering component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected Steering mount (2.1.2 (e) (ii)) | 1 |
| Central Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Innersill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Central Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Front Suspension component corroded and seriously weakened Cross member (5.3.3 (b) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis/outrigger |5.3.6 |a| |i|| | 1 |
| Nearside Outer Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Outer Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Front Wheel nut|s| loose |4.2.A.1e| | 1 |
| Offside Front Wheel insecure |4.2.A.1c| | 1 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| rear brake grabbing severely |3.7.A.5b| | 1 |
| Rear brake binding | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| An item not tested |Manual| | 1 |
| Offside Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Offside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Parking |secondary brake| on a single line braking system grabbing severely BOTH SIDES |1.3.1 |c|| | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Battery insecure |1.9.1| | 1 |
| Nearside Front Wheel nut|s| missing 2 |4.2.A.1e| | 1 |
| Offside Front Wheel nut|s| missing 2 |4.2.A.1e| | 1 |
| Nearside Rear Wheel nut|s| missing 3 |4.2.A.1e| | 1 |
| Offside Rear Wheel nut|s| missing 1 |4.2.A.1e| | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Rear Exhaust has a major leak of exhaust gases box |6.1.2 |a|| | 1 |
| Undertray insecure |8.1.1 |b| |i|| | 1 |
| Emissions not tested |8.2.1.2 |d|| | 1 |
| Emissions not tested due to exhaust leak |8.2.1.2 |d|| | 1 |
| Nearside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced lens damaged |4.1.4 |b|| | 1 |
| Offside Headlamp light intensity severely reduced lens faded and incorrect bulb |4.1.4 |a|| | 1 |
| Offside Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis,upper coil spring mount area |5.3.6 |a| |i|| | 1 |
| Emissions not tested engine oil level at lowest limit |8.2.1.2 |d|| | 1 |
| Nearside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill panel |5.3.6 |a| |i|| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill panel |5.3.6 |a| |i|| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt both |2.4.G.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill panel |2.4.A.3| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Road wheel fractured |4.2.B.1a| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Body component likely to become detached bumper bar |6.2.1 |a| |ii|| | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced bar |6.1.1 |c| |i|| | 1 |
| Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |