| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 31 |
| Registration plate lamp issues | 10 |
| Offside Rear fog lamp not working |1.3.2b| | 10 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 6 |
| Brake pipe excessively corroded | 6 |
| Rear fog lamp missing |1.3.2a| | 5 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 5 |
| Brakes imbalanced across an axle | 5 |
| Headlamp aim out of alignment | 5 |
| Rear fog lamp tell tale not working |1.3.1b| | 4 |
| Rear fog lamp not working |1.3.2b| | 4 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
| Rear fog lamp switch missing |1.3.1a| | 3 |
| Battery insecure |1.9.1| | 3 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Driver`s airbag obviously defective |5.4.1| | 3 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 3 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 3 |
| Rear Exhaust system not adequately supported |7.1.1| | 3 |
| Offside Rear fog lamp missing |1.3.2a| | 2 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 2 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Offside Stop lamp not working |1.2.1b| | 2 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 2 |
| Offside Front front brake binding |3.7.B.1| | 2 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Windscreen wiper blade insecure | 2 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Anti-lock braking system warning lamp indicates an ABS fault | 2 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 2 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Centre Exhaust system not adequately supported |7.1.1| | 2 |
| Rear brake binding | 2 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside Side repeater not working |1.4.A.2c| | 2 |
| Offside Rear fog lamp insecure |1.3.2a| | 2 |
| Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
| Offside Rear Inner Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
| Rear fog lamp tell tale missing |1.3.1b| | 2 |
| Offside Rear Stop lamp not working |1.2.1b| | 2 |
| Nearside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 2 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 2 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Offside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Rear Rear fog lamp insecure |1.3.2a| | 1 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded middle inner sill |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Front All position lamps not working |4.2.1 |a|| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Rear Anti-roll bar linkage pin or bush likely to become detached |5.3.4 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings at inner cill, 2 places |6.1.B.2| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion at outer wing, 2 places |6.1.C.1| | 1 |
| Offside Front Power steering ram|s| leaking from a failed component steering rack leaking |2.3.3b| | 1 |
| Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Rear Position lamp lens seriously defective broken |4.2.1 |b|| | 1 |
| Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill in 3 X places |6.2.2 |d| |i|| | 1 |
| Offside Rear Passenger`s seat insecure |6.2.A.1| | 1 |
| Anti-roll bar has excessive play in a pin/bush both rear |2.4.G.2| | 1 |
| Valve stem seriously damaged both front |4.1.D.1e| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill / arch |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel well |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded o/s/f inner sill |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced main front cross member (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills (6.1.1 (c) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills (6.1.1 (c) (i)) | 1 |
| Offside Front Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
| Offside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
| Service brake: efficiency below requirements |3.7.C.1a| | 1 |
| Offside Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear brake disc in such a condition that it is seriously weakened | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| All position lamps not working |4.2.1 |a|| | 1 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Headlamp switch faulty |1.7.1| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Offside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases rear box to pipe flandge / and cat |7.1.2| | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch spring mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced door shut (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis arm mount (5.3.6 (a) (i)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached |5.3.4 |a| |ii|| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Rear parking brake recording little or no effort | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded outrigger |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded inner and outer sill front and rear |2.4.A.3| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded inner and outer sill front and rear |2.4.A.3| | 1 |
| Rear Inner Seat belt anchorage prescribed area is excessively corroded valance to floor |5.2.6| | 1 |
| Windscreen has damage | 1 |
| Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Nearside Front Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Rear Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced (6.1.1 (b) (ii)) | 1 |
| Rear fog lamp likely to become detached |4.5.1 |c| |ii|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Windscreen washer not working | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting cracked |2.4.G.1| | 1 |
| Offside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill back/floor |5.3.6 |a| |i|| | 1 |
| Supplementary Restraint System warning lamp indicates a fault |5.4.2| | 1 |
| Nearside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Power steering component|s| leaking from a failed seal |2.3.3b| | 1 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
| Front Windscreen has a combination of minor damage areas which restrict the drivers view |8.3.1c| | 1 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 1 |
| Position lamp switch faulty |1.1.A.1| | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Horn sound not in accordance with requirements (7.7 (c)) | 1 |
| Oil leaking continuously from engine posing a serious risk to road safety (8.4.1 (a) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength large hole in cill (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Rear Inner Anti-roll bar rubber bush deteriorated resulting in excessive movement `D` |2.4.G.2| | 1 |
| Offside Rear Inner Anti-roll bar rubber bush deteriorated resulting in excessive movement `D` |2.4.G.2| | 1 |
| Nearside Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded nsf inner sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded osf inner sill |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded chassis more than on area |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded chassis more than one area |2.4.A.3| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Suspension arm severely distorted |2.4.G.1| | 1 |
| Offside Front Suspension arm severely distorted |2.4.G.1| | 1 |
| Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt both front |2.1.3 |g| |ii|| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill full length |5.2.6| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded sill full length |5.2.6| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 1 |
| Nearside Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cross member |6.1.B.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced under wheel arch holed |7.1.1 |a| |i|| | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed |7.1.1 |a| |i|| | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Rear Parking |secondary brake| on a single line braking system has inadequate effort at a wheel |1.3.1 |a| |i|| | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed front and rear (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed front to rear (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer and inner wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer and inner wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Anti-roll bar pin or bush excessively worn nearside rear inner D bush (5.3.4 (a) (i)) | 1 |
| Anti-roll bar pin or bush excessively worn offside rear inner D bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Nearside Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Anti-roll bar insecure |2.4.G.1| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Wheel nut|s| missing |4.2.A.1e| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Offside Obligatory mirror not clearly visible from the drivers seat or incapable of being adjusted to be clearly visible from the driver`s seat |8.1.1d| | 1 |
| Offside Front Track rod end ball joint dust cover missing |2.2.C.1c| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Offside Front Track rod end loose |2.2.B.1d| | 1 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Front Front constant velocity joint is excessively worn |2.5.C.1b| | 1 |
| Nearside Rear Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Body component corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill middle to front |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill front to rear |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill front to rear |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Rear fog lamp tell tale missing in cab |1.3.1b| | 1 |
| Offside Front Lower Suspension arm has excessive play in a pin/bush inner rear bush |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner sill cross-member section |2.4.A.3| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner and outer sill section |6.1.B.2| | 1 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill, numerous sections |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings where the rear cross-member joins |6.1.B.2| | 1 |
| Nearside Rear Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Lower Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |