Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 48 |
Registration plate lamp issues | 20 |
Rear fog lamp not working |1.3.2b| | 17 |
Headlamp aim out of alignment | 11 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 11 |
Exhaust has a major leak of exhaust gases |7.1.2| | 11 |
Offside Rear fog lamp not working |1.3.2b| | 9 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
Horn not working |1.6.2a| | 7 |
Brake pipe excessively corroded | 7 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 6 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Rear fog lamp tell tale not working |1.3.1b| | 6 |
Offside Rear fog lamp missing |1.3.2a| | 5 |
Offside Headlamp not working on dipped beam |1.7.5a| | 4 |
Rear fog lamp missing |1.3.2a| | 4 |
Offside Front position lamp|s| not working |1.1.A.3b| | 4 |
Offside Stop lamp not working |1.2.1b| | 4 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
Parking brake lever has no reserve travel |3.1.6b| | 4 |
Registration plate issues | 4 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 4 |
Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 4 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 4 |
Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 4 |
Windscreen washer not working | 3 |
Rear Exhaust system not adequately supported |7.1.1| | 3 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 3 |
Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
Rear fog lamp switch missing |1.3.1a| | 3 |
Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 3 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 3 |
Offside Rear Rear fog lamp not working |1.3.2b| | 3 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 3 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 3 |
Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 3 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 3 |
Rear brake binding | 3 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 3 |
Front brake disc in such a condition that it is seriously weakened | 3 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Offside Rear Rear fog lamp missing |1.3.2a| | 2 |
Rear brake disc in such a condition that it is seriously weakened | 2 |
Power steering component|s| leaking |2.3.3b| | 2 |
Offside Front Direction indicators not working |1.4.A.2c| | 2 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 2 |
Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill to floor |2.4.A.3| | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 2 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 2 |
Nearside Stop lamp not working |1.2.1b| | 2 |
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
All position lamps not working |1.1.A.3b| | 2 |
Speedometer cannot be illuminated. |6.7.3| | 2 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Emissions not tested |7.0| | 2 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 2 |
Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Service brake: efficiency below requirements |3.7.C.1a| | 2 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
Offside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 2 |
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Nearside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
Offside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 2 |
Parking brake: efficiency below requirements |3.7.B.7| | 2 |
Emissions not tested |7.4.B.1| | 2 |
Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Brakes imbalanced across an axle | 2 |
Nearside front brake binding |3.7.B.1| | 2 |
Anti-lock braking system warning lamp indicates an ABS fault | 2 |
Parking brake: efficiency below requirements |3.7.C.1b| | 2 |
Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 2 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 2 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 2 |
Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Headlamp not working on main beam |1.7.5a| | 2 |
Offside Steering rack gaiter split |2.2.D.2d| | 2 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Rear fog lamp tell tale missing |1.3.1b| | 2 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front Position lamp not working |4.2.1 |a|| | 2 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
Offside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 2 |
Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
Rear fog lamp emits a light other than red |1.3.2e| | 2 |
Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Offside Rear Direction indicator not working |1.4.A.2c| | 2 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 2 |
Offside Rear Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 1 |
Nearside Rear Statutory seat belt missing |5.1.1| | 1 |
Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt inner boot |6.1.7 |g| |ii|| | 1 |
Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc inner |2.5.C.1a| | 1 |
Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
Nearside Front Windscreen wiper blade missing |8.2.2| | 1 |
Offside Front Lower Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Nearside Rear Body has a projection caused by corrosion |6.1.C.1| | 1 |
Offside Rear Body has a projection caused by corrosion |6.1.C.1| | 1 |
Offside Front All position lamps not working |1.1.A.3b| | 1 |
Exhaust emits excessive smoke or vapour of any colour white smoke |7.4.B.4| | 1 |
Offside Rear Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
Rear Seat belt anchorage prescribed area is excessively corroded behind bumper several places corroded |marked| |5.2.6| | 1 |
Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded front sill |5.2.6| | 1 |
Offside Rear Inner Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
Front position lamp|s| not working Both |1.1.A.3b| | 1 |
Rear Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
Rear Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Nearside Rear Seat belt buckle missing (7.1.2 (d)) | 1 |
Offside Rear Seat belt buckle missing (7.1.2 (d)) | 1 |
Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Central Exhaust has a major leak of exhaust gases joint (6.1.2 (a)) | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Offside Front Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 1 |
Offside Rear Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
Nearside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Horn not working |7.7 |a| |ii|| | 1 |
Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Nearside Rear brake disc contaminated by oil |3.5.1h| | 1 |
Nearside Inner Rear brake drum contaminated by oil |3.5.1h| | 1 |
Rear Rear fog lamp not working |1.3.2b| | 1 |
Nearside Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Rear Anti-roll bar missing |2.4.G.1| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill/wheel arch corroded within 30cm of suspension mounting (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill excessively corroded within 30cm of suspension mount (5.3.6 (a) (i)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill/wheel arch excessively corroded within 30cm of suspension mount (5.3.6 (a) (i)) | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Crossmember (7.1.1 (a) (i)) | 1 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Crossmember (7.1.1 (a) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Front crossmember (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength front crossmember (5.3.6 (a) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking points (6.2.2 (d) (i)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking points (6.2.2 (d) (i)) | 1 |
Headlamps matched pair are not the same colour |1.7.6| | 1 |
Nearside Rear Anti-roll bar attachment bracket/mounting insecure d-bush missing |2.4.G.1| | 1 |
Offside Front Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
Offside Rear brake disc contaminated by oil |3.5.1h| | 1 |
Offside Front Position lamp not working |4.2.1 |a| |ii|| | 1 |
Nearside Headlamp insecure |4.1.1 |c|| | 1 |
Offside Headlamp insecure |4.1.1 |c|| | 1 |
Offside Front Body component damaged and likely to cause injury |6.2.1 |a| |i|| | 1 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Offside Front Seat belt stitching badly frayed |5.2.2b| | 1 |
Nearside Front Wheel nut|s| missing |4.2.A.1e| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
Offside Front Headlamp light intensity severely reduced |4.1.4 |a|| | 1 |
Nearside Front Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 1 |
Nearside Front Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 1 |
Offside Front Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
Nearside Headlamp light intensity severely reduced |4.1.4 |a|| | 1 |
Offside Headlamp light intensity severely reduced |4.1.4 |a|| | 1 |
Offside Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
Nearside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded sill to floor |2.4.A.3| | 1 |
Towbar excessively corroded within 30cm of towbar mounting Rear Crossmember Between Mounts (6.1.6 (i) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outrigger/Floor (5.3.6 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases Broken in Half and Badly Corroded (6.1.2 (a)) | 1 |
Exhaust silencer likely to become detached Rear Silencer/Section (8.1.1 (b) (ii)) | 1 |
Emissions not tested (8.2.2.2 (e)) | 1 |
Rear Parking (secondary brake) on a single line braking system grabbing severely BOTH SIDES N/S O/S (1.3.1 (c)) | 1 |
Rear Service brake grabbing severely BOTH SIDES N/S O/S (1.2.1 (c)) | 1 |
Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
Nearside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
Offside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
Nearside Rear Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Front Steering rack gaiter missing or no longer prevents the ingress of dirt both front each side torn (2.1.3 (g) (ii)) | 1 |
Nearside Front Suspension arm ball joint excessively worn also cover torn (5.3.4 (a) (i)) | 1 |
Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt both front each side torn (2.1.3 (g) (ii)) | 1 |
Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt also with play (5.3.4 (b) (ii)) | 1 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` stickers |8.3.1e| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded view from wheel arch chassis leg |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded view from wheel arch chassis leg |2.4.A.3| | 1 |
Rear Suspension component mounting prescribed area is excessively corroded cross member by exhaust |2.4.A.3| | 1 |
Headlamp lens seriously defective both |4.1.1 |b| |ii|| | 1 |
Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill in the centre |6.1.1 |c| |i|| | 1 |
Power steering pipe/hose leaking |2.1.5 |a|| | 1 |
Oil leaking excessively from engine |8.4.1 |a| |i|| | 1 |
Nearside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
Offside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Front brake excessively fluctuating | 1 |
Nearside rear brake excessively fluctuating |3.7.B.3| | 1 |
Rear parking brake recording little or no effort | 1 |
rear parking |secondary| brakes imbalanced | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush d bush |2.4.G.2| | 1 |
Offside Rear Anti-roll bar linkage has excessive play in a pin/bush d bush |2.4.G.2| | 1 |
Windscreen has damage | 1 |
Offside Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Front Shock absorber has negligible damping effect |2.7.5| | 1 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
Central Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cross member holed |6.1.B.2| | 1 |
Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill to floor holed |6.1.B.2| | 1 |
Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill to floor holed |6.1.B.2| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under wheel arch holed |6.1.B.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under wheel arch holed |6.1.B.2| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under wheel arch holed |6.1.B.2| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under wheel arch holed |6.1.B.2| | 1 |
Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
Offside Rear Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor nr tow bar |6.1.B.2| | 1 |
Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Front Seat belt webbing significantly weakened |7.1.2 |b| |ii|| | 1 |
Nearside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Offside Rear Anti-roll bar cracked |2.4.G.1| | 1 |
Nearside Rear Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 1 |
Nearside Rear Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill/step (7.1.1 (a) (i)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced innersill/step (7.1.1 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outter sill (7.1.1 (a) (i)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outter sill (7.1.1 (a) (i)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
Central Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill |6.1.B.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill |6.1.B.2| | 1 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Rear Body has a projection caused by corrosion holes in inner and outer sills |6.1.C.1| | 1 |
Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
Nearside Rear reflector missing |1.5.1a| | 1 |
Power steering inoperative |2.3.3a| | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 1 |
Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
Offside Stop lamp(s) showing white light to the rear (4.3.3 (a) (ii)) | 1 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Road wheel fixing missing front + rear (5.2.1 (a) (i)) | 1 |
Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength nearside + offside rear chassis legs (5.3.6 (a) (i)) | 1 |
Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded inner wheel arch |5.2.6| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill behind wheel |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill behind wheel |5.2.6| | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting cross member |6.6.6| | 1 |
Centre Vehicle structure excessively corroded within 30cm of towbar mounting cross member |6.6.6| | 1 |
Towbar component insecure |6.6.1| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
Offside Body insecure and dangerous to other road users side step |6.1.B.1b| | 1 |
Nearside Towbar is so weakened by damage within 30cm of a towbar mounting, the towbar is likely to become detached (6.1.6 (i) (ii)) | 1 |
Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Front Vehicle structure has excessive corrosion which adversely affects braking or steering crossmember |6.1.A.1| | 1 |
Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Offside Rear fog lamp likely to become detached |4.5.1 |c| |ii|| | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
Offside Inner Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Vehicle Identification Number not legible |6.3.5.a| | 1 |
Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill x3 (6.1.1 (c) (i)) | 1 |
Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
Nearside Front Service brake excessively binding |1.2.1 |f|| | 1 |
Offside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength sill corroded (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension spring mounting prescribed area excessively damaged significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting above exhaust (6.1.6 (i) (i)) | 1 |
Nearside Rear Inner Suspension spring mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Rear Outer Suspension spring mounting prescribed area excessively damaged significantly reducing structural strength sill corroded (5.3.6 (a) (i)) | 1 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
Offside Front Headlamp lens seriously defective high (4.1.1 (b) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Rear Seat belt buckle missing trapped under seat |7.1.2 |d|| | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Nearside Front Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
Offside Front Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
Nearside Rear Valve stem seriously damaged |5.2.3 |j|| | 1 |
Offside Rear Valve stem seriously damaged |5.2.3 |j|| | 1 |
Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember |5.3.6 |a| |i|| | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Rear Front position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Offside Inner Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under step/outrigger |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under step/outrigger |5.3.6 |a| |i|| | 1 |
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting under quarter |6.6.6| | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting cross member x 2 |6.6.6| | 1 |
Nearside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill back/floor (5.3.6 (a) (i)) | 1 |
Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Nearside rear lower sill section (6.2.2 (d) (i)) | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting offside rear lower outer sill section (6.2.2 (d) (i)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength offside rear lower (5.3.6 (a) (i)) | 1 |
Battery insecure |1.9.1| | 1 |
Nearside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis rail (5.3.6 (a) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis section (5.3.6 (a) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis rail (5.3.6 (a) (ii)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced centre sill section (7.1.1 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis (5.3.6 (a) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected chassis (5.3.6 (a) (ii)) | 1 |
Offside Rear Hazard warning lamps inoperative |1.4.B.1b| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings most of inner sill rusted away |6.1.B.2| | 1 |
Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings most of inner sill rusted and holed |6.1.B.2| | 1 |
Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded behind mud flap |2.4.A.3| | 1 |
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Offside Front Direction indicator not working |1.4.A.2c| | 1 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Battery insecure |1.9.1| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded front to rear sill to floor |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded front to rear sill to floor |5.2.6| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch behind mud flap |2.4.A.3| | 1 |
Nearside Rear Parking brake is not capable of being maintained in operation by direct mechanical action only seized |3.1.2| | 1 |
Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Exhaust has a major leak of exhaust gases centre and rear |6.1.2 |a|| | 1 |
Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
Nearside Front Headlamp has a product on the lens so that the light output is severely reduced tarnished |4.1.4 |b|| | 1 |
Offside Front Headlamp has a product on the lens so that the light output is severely reduced tarnished |4.1.4 |b|| | 1 |
Nearside Rear Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Rear Lower Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Rear Lower Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Headlamp aim beam image obviously incorrect both |1.8.A.1b| | 1 |
Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Drivers door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
Offside Front Shock absorbers has a serious fluid leak | 1 |
Nearside Rear Inner Vehicle structure excessively corroded within 30cm of towbar mounting crossmember (6.1.6 (i) (i)) | 1 |
Offside Rear Inner Vehicle structure excessively corroded within 30cm of towbar mounting crossmember (6.1.6 (i) (i)) | 1 |
Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
Offside Front Passenger`s seat insecure |6.2.A.1| | 1 |
Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 1 |
Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear An item not tested |Manual| | 1 |
Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Offside Front Anti-roll bar ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
Offside Front Service brake lagging in operation |1.2.1 |d|| | 1 |
Offside Front front brake binding |3.7.B.1| | 1 |
Nearside Front Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
Offside Front Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Central Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cross member |6.1.B.2| | 1 |