| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 45 |
| Headlamp aim out of alignment | 20 |
| Rear fog lamp not working |1.3.2b| | 14 |
| Registration plate lamp issues | 13 |
| Offside Rear fog lamp not working |1.3.2b| | 11 |
| Offside Stop lamp not working |1.2.1b| | 10 |
| Nearside Stop lamp not working |1.2.1b| | 10 |
| Brake pipe excessively corroded | 10 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 9 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 8 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 7 |
| Horn not working |1.6.2a| | 7 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 6 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 6 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 6 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 5 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Rear fog lamp tell tale not working |1.3.1b| | 5 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 4 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Rear fog lamp missing |1.3.2a| | 4 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 4 |
| Nearside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
| Offside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
| Offside Steering rack gaiter split |2.2.D.2d| | 4 |
| Battery insecure |1.9.1| | 3 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 3 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Parking brake: efficiency below requirements |3.7.B.7| | 3 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Windscreen washer not working | 3 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 3 |
| Nearside Rear Braking system leaking |3.6.A.1| | 3 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 3 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 3 |
| Power steering component|s| leaking |2.3.3b| | 3 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 3 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 2 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Rear parking brake recording little or no effort | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Nearside Front Direction indicator insecure |1.4.A.2b| | 2 |
| Rear fog lamp switch missing |1.3.1a| | 2 |
| Brakes imbalanced across an axle | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 2 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
| Power steering component|s| leaking from a failed seal |2.3.3b| | 2 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Service brake: efficiency below requirements |3.7.C.1a| | 2 |
| Nearside Front Service brake excessively binding |1.2.1 |f|| | 2 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Rear brake disc contaminated by oil |3.5.1h| | 2 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Anti-lock braking system warning lamp indicates an ABS fault | 2 |
| Offside Side repeater not working |1.4.A.2c| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Passenger`s seat cannot be secured in the upright position. |6.2.A.2| | 2 |
| Nearside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Emissions not tested |7.0| | 2 |
| Rear Rear fog lamp missing |1.3.2a| | 2 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Offside Rear fog lamp emits a light other than red White Lamp & Lens - Recommend fitting of a Red Lamp/LED |1.3.2e| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Lower Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Emissions not tested (8.2.2.2 (e)) | 1 |
| Rear brake application uneven | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Offside Side repeater not working |4.4.1 |a| |ii|| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear Inner Anti-roll bar linkage attachment bracket/mounting likely to fail (5.3.3 (b) (ii)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Fuel system component leaking pump |7.2.3| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Mechanical brake component has restricted free movement | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Rear Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Front Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 1 |
| Upper Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement d-bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement d-bush |2.4.G.2| | 1 |
| Offside Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Offside Front Battery insecure and likely to fall from carrier battery tray holed at securing device (4.13 (a) (ii)) | 1 |
| Nearside Inner Suspension component mounting prescribed area fractured significantly reducing structural strength inner upper wheel arch holed in 2 places (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area fractured significantly reducing structural strength inner wheel arch holed (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill hole in place by osf door (7.1.1 (a) (i)) | 1 |
| Nearside Rear Upper Vehicle structure is fractured and structural rigidity is significantly reduced toe bar prescribed area hole marked yellow (6.1.1 (a) (i)) | 1 |
| Offside Rear Upper Vehicle structure is fractured and structural rigidity is significantly reduced toe bar prescribed area holed marked yellow (6.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure is fractured and structural rigidity is significantly reduced inner rear upper wheel area holed (6.1.1 (a) (i)) | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember |5.3.6 |a| |i|| | 1 |
| front brake binding |3.7.B.1| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Brake pedal has insufficient reserve travel |1.1.2 |a|| | 1 |
| Nearside Rear brake disc excessively pitted |3.5.1h| | 1 |
| Offside brake disc excessively pitted |3.5.1h| | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Rear Exhaust system insecure mount broken (6.1.2 (a)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Direction indicator not working re new bud and make work (4.4.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases back box holed (6.1.2 (a)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Rear Rear passenger seat cannot be secured in the upright position. |6.2.3| | 1 |
| Offside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Offside Stop lamp insecure |1.2.1a| | 1 |
| Offside Rear reflector insecure |1.5.1a| | 1 |
| Offside Direction indicator insecure |1.4.A.2b| | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Rear fog lamp insecure |1.3.2a| | 1 |
| Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear fog lamp likely to become detached |4.5.1 |c| |ii|| | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Offside Rear Lower Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Rear Brake disc contaminated |1.1.14 |b|| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member n/s and o/s (5.3.6 (a) (i)) | 1 |
| Offside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill and sill end |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
| Nearside Rear Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Nearside Battery insecure leisure battery |1.9.1| | 1 |
| Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Rear brake disc contaminated by oil |3.5.1h| | 1 |
| Exhaust has a major leak of exhaust gases Back box |7.1.2| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt split (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt split (5.3.4 (b) (ii)) | 1 |
| Rear fog lamp tell tale missing |1.3.1b| | 1 |
| Windscreen wiper blade missing |8.2.2| | 1 |
| Nearside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill hole (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL |5.3.6 |a| |i|| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL |5.3.6 |a| |i|| | 1 |
| Rear Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill [front,centre and rear] |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Rear Exhaust has a part missing |7.1.1a| | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Rear brake disc excessively pitted |3.5.1h| | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced centre (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill near axle mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section and front of sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Lower Front suspension has excessive movement at a suspension ball joint |2.5.A.1c| | 1 |
| Nearside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Valve stem seriously misaligned (5.2.3 (j)) | 1 |
| Nearside Rear Valve stem seriously misaligned (5.2.3 (j)) | 1 |
| Nearside Inner Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Inner Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Outer Front Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Stop lamp not working all stop lights |1.2.1b| | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 2 places (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength 2 places (5.3.6 (a) (i)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Offside Rear Anti-roll bar pin or bush likely to become detached bush missing (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Front Suspension component mounting prescribed area is excessively corroded inner crossmember o/s n/s |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Central Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Rear Passenger`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Power steering pump drive system defective |2.3.6| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting x member |6.6.6| | 1 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill corroded |5.3.6 |a| |i|| | 1 |
| Offside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Inner Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Inner Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Nearside Rear position lamp|s| incorrect colour white light showing |1.1.A.3e| | 1 |
| Steering system excessively rough |2.2.D.1| | 1 |
| Suspension component mounting prescribed area is excessively corroded o/s areas |2.4.A.3| | 1 |
| Power steering component|s| leaking rack |2.3.3b| | 1 |
| Nearside Outer Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded front cross member |2.4.A.3| | 1 |
| front brake binding both front |3.7.B.1| | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Front Horn not working |1.6.2a| | 1 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis next to inner sill |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
| Offside Front Upper Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt drop link boot |2.4.G.2| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sil |6.1.B.2| | 1 |
| Nearside Rear Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear brake disc contaminated by brake fluid |3.5.1h| | 1 |
| Nearside Headlamp aim beam image obviously incorrect no beam image |1.8.A.1b| | 1 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Front Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Exhaust on a vehicle fitted with a diesel particulate filter emits visible smoke of any colour |8.2.2.2 |d|| | 1 |
| Fluid leak harmful to the environment or a risk to other road users |8.4.1 |a| |i|| | 1 |
| Fluid leak harmful to the environment or a risk to other road users coolant |8.4.1 |a| |i|| | 1 |
| Nearside Rear Shock absorbers likely to become detached |5.3.2 |a| |ii|| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill |5.3.6 |a| |i|| | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Exhaust has a major leak of exhaust gases Rear section |7.1.2| | 1 |
| Nearside Battery insecure |1.9.1| | 1 |
| Nearside Front Outer Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension arm mounting housing. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Stop lamp|s| adversely affected by the operation of another lamp |4.3.3 |b|| | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill front to rear (7.1.1 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded outer sill in several areas |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded outer sill in several areas |2.4.A.3| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded inner sill in several areas |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded inner sill in several areas |2.4.A.3| | 1 |
| Rear Prop shaft securing bolt missing (6.1.7 (a) (i)) | 1 |
| Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt Both links boots perished and split |2.4.G.2| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Rear Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Centre Power steering ram|s| leaking from a failed component |2.3.3b| | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn rear rubber bush worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill back/floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn Rear bush (5.3.4 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front cross member (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced By lower arm mount (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
| Offside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill to floor |2.4.A.3| | 1 |
| Power steering component|s| leaking steering rack |2.3.3b| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded radiator mount |2.4.A.3| | 1 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Registration plate issues | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor |7.1.1 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor |7.1.1 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Centre Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced siil |6.1.1 |c| |i|| | 1 |
| Offside Rear Inner Vehicle structure is fractured and structural rigidity is significantly reduced sill, poor repair |6.1.1 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Fluid leaking continuously posing a serious risk to road safety Coolant (8.4.1 (a) (ii)) | 1 |
| Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 1 |
| Emissions not tested Due to condition of coolant leak and exhaust (8.2.2.2 (e)) | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen |1.8.B.1| | 1 |