| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 36 |
| Registration plate lamp issues | 35 |
| Windscreen wiper does not clear the windscreen effectively | 34 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 14 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 13 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 11 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 10 |
| Offside Rear fog lamp not working |1.3.2b| | 10 |
| Brake hose excessively deteriorated | 8 |
| Parking brake: efficiency below requirements |3.7.B.7| | 7 |
| Rear fog lamp not working |1.3.2b| | 7 |
| Offside Rear fog lamp missing |1.3.2a| | 6 |
| Registration plate issues | 6 |
| Brake pipe excessively corroded | 6 |
| Nearside Stop lamp not working |1.2.1b| | 6 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 6 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 5 |
| Offside Stop lamp not working |1.2.1b| | 5 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 5 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 5 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 5 |
| Anti-lock braking system warning lamp indicates an ABS fault | 4 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 4 |
| Rear parking brake recording little or no effort | 4 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 4 |
| Rear fog lamp tell tale not working |1.3.1b| | 4 |
| Exhaust system not adequately supported |7.1.1| | 4 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 4 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 3 |
| Service brake: efficiency below requirements |3.7.B.7| | 3 |
| Rear fog lamp switch missing |1.3.1a| | 3 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 3 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 3 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 3 |
| Offside Side repeater not working |1.4.A.2c| | 3 |
| Offside Rear Stop lamp not working |1.2.1b| | 3 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 3 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 3 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Rear fog lamp emits a light other than red |1.3.2e| | 3 |
| Brakes imbalanced across an axle | 3 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Nearside Front Headlamp insecure |1.7.3| | 2 |
| Offside Rear Wheel nut|s| missing |4.2.A.1e| | 2 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 2 |
| Nearside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Rear fog lamp tell tale missing |1.3.1b| | 2 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 2 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Windscreen has damage | 2 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Rear Shock absorbers has a serious fluid leak | 2 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 2 |
| Offside Rear fog lamp insecure |1.3.2a| | 2 |
| Rear fog lamp missing |1.3.2a| | 2 |
| Horn not working |1.6.2a| | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 2 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Nearside Ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 2 |
| Emissions not tested (8.2.1.2 (d)) | 2 |
| Centre Stop lamp not working |1.2.1b| | 2 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Rear Braking system leaking |3.6.A.1| | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Battery insecure |1.9.1| | 2 |
| Hazard warning switch faulty |1.4.B.1d| | 2 |
| Driver`s door cannot be opened from inside the vehicle |6.2.B.1b| | 2 |
| Nearside Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
| Front brake application uneven | 2 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 2 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Nearside Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Centre Rear Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 1 |
| Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill Area (6.1.1 (c) (i)) | 1 |
| Braking system leaking front to back brake pipe |3.6.A.1| | 1 |
| Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Brake lever has insufficient reserve travel |1.1.2 |a|| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Rear Exhaust has a part missing |7.1.1a| | 1 |
| Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Front Shock absorber has negligible damping effect |2.7.5| | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Offside Side repeater insecure |1.4.A.2b| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Rear Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
| Offside Headlamp insecure |1.7.3| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Exhaust engine idle speed too high |7.3.D.1| | 1 |
| Electronic stability system warning lamp indicates a fault |3.4.1c| | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Vehicle structure is deformed and structural rigidity is significantly reduced sill and mount (6.1.1 (a) (i)) | 1 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Offside Front brake caliper securing device loose |3.5.1j| | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength by shockabsorber mounting inner chassis (5.3.6 (a) (i)) | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded rear inner sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded rear inner sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded crossember |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded crossember |2.4.A.3| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush d bush |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush d bush |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded innewr sill x 2 |2.4.A.3| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Ball joint has excessive play |2.2.B.1f| | 1 |
| Trailer electrical socket |13 pin| not operating the trailer lamps as intended |1.9.4| | 1 |
| Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Crossmember |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Crossmember |5.3.6 |a| |i|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Fuel cap/sealing device missing cap missing (6.1.3 (b) (i)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light white light (4.5.4 (a)) | 1 |
| Offside Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Rear fog lamp switch inoperative |4.5.3 |a| |ii|| | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill , floor pan area- corroded and rotten through (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill , floor pan area- corroded and rotten through (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Offside Front Direction indicators not working |1.4.A.2c| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
| brake disc excessively pitted |3.5.1h| | 1 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Obligatory mirror missing |8.1.1| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 1 |
| Offside Headlamp aim not tested |1.8.A.1c| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Front brake disc excessively scored |3.5.1h| | 1 |
| Nearside Front brake disc excessively scored |3.5.1h| | 1 |
| Nearside Front brake caliper has restricted free movement |3.5.1k| | 1 |
| Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Rear brake disc in such a condition that it is seriously weakened | 1 |
| Nearside Rear rear brake recording little or no effort parking |3.7.B.5a| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Braking system leaking |3.6.A.1| | 1 |
| Nearside Outer Front Front position lamp|s| insecure |1.1.A.3a| | 1 |
| Nearside Front coil spring incomplete |2.4.C.1a| | 1 |
| Offside Front coil spring incomplete |2.4.C.1a| | 1 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Emissions not tested |7.0| | 1 |
| Rear Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Rear Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Rear position lamp|s| not working side light |1.1.A.3b| | 1 |
| Direction indicators incorrect colour both front |1.4.A.2f| | 1 |
| Offside Front coil spring broken |2.4.C.1a| | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Front Ball joint has excessive play drumstick |2.2.B.1f| | 1 |
| Nearside Side repeater incorrect colour |1.4.A.2f| | 1 |
| Nearside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement damaged |7.2.4b| | 1 |
| Nearside Rear coil spring fractured |2.4.C.1a| | 1 |
| Offside Rear Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear coil spring broken |2.4.C.1a| | 1 |
| Offside Front Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 1 |
| Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under step (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under step (5.3.6 (a) (i)) | 1 |
| Stop lamp not working ns+os |1.2.1b| | 1 |
| Offside Front Lower Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Offside Rear Towbar excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt Insecure (5.3.4 (b) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Position lamp not working |4.2.1 |a| |ii|| | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Nearside Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Offside Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Offside Rear Stop lamp(s) emits other than a steady red light (4.3.3 (a) (ii)) | 1 |
| Nearside Front Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement d bush |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement d bush |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Headlamp aim not tested both (4.1.2 (b)) | 1 |
| Headlamp lens seriously defective both (4.1.1 (b) (ii)) | 1 |
| Drivers door cannot be opened from inside the vehicle handle broken off (6.2.3 (a)) | 1 |
| Headlamp aim not tested both-no beam image (4.1.2 (b)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember in several places (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (rearmost seatbelt) (7.1.1 (a) (i)) | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill x2 (6.2.2 (d) (i)) | 1 |
| Headlamp aim so that beam "kick up" is not visible on the screen both sides |4.1.2 |a|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Nearside Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Offside Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/out rigger |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/outrigger |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light white (4.5.4 (a)) | 1 |
| Nearside Rear Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected battery terminal (4.11 (a) (ii)) | 1 |
| Rear Seat belt missing buckles (7.1.2 (a)) | 1 |
| Exhaust system insecure mounting broken (6.1.2 (a)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
| Offside Inner Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Rear fog lamp tell-tale not working |4.9.1 |a| |ii|| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn D-bushes (5.3.4 (a) (i)) | 1 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Rear Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Headlamp aim not tested (4.1.2 (b)) | 1 |
| Central Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
| Rear brake binding | 1 |
| Nearside Front All position lamps not working |1.1.A.3b| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Offside Front coil spring fractured |2.4.C.1a| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |