Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 39 |
Brake pipe excessively corroded | 17 |
Registration plate lamp issues | 17 |
Headlamp aim out of alignment | 15 |
Offside Rear fog lamp not working |1.3.2b| | 11 |
Rear fog lamp not working |1.3.2b| | 9 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 6 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
Front brake disc in such a condition that it is seriously weakened | 4 |
Offside Front position lamp|s| not working |1.1.A.3b| | 4 |
Registration plate issues | 4 |
Brakes imbalanced across an axle | 4 |
Parking brake: efficiency below requirements |3.7.B.7| | 3 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Offside Rear Rear fog lamp not working |1.3.2b| | 3 |
Offside Stop lamp not working |1.2.1b| | 3 |
Offside Rear Leaf spring fractured |2.4.B.1a| | 3 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
Brake load sensing valve linkage seized |3.6.E.3| | 2 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front Steering rack gaiter split |2.2.D.2d| | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 2 |
Nearside Front Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 2 |
Rear brake application uneven | 2 |
Front Subframe mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 2 |
Offside Steering rack gaiter insecure |2.2.D.2d| | 2 |
Centre Front Seat belt locking mechanism does not secure or release |5.2.5a| | 2 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Nearside Stop lamp not working |1.2.1b| | 2 |
Horn not working |1.6.2a| | 2 |
Rear Rear fog lamp not working |1.3.2b| | 2 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 2 |
Nearside Rear Leaf spring fractured |2.4.B.1a| | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 2 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
Rear parking brake recording little or no effort | 2 |
Offside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 2 |
Driver`s seat insecure |6.2.A.1| | 1 |
Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 1 |
Nearside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Anti-roll bar linkage severely distorted |2.4.G.1| | 1 |
Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Rear brake binding | 1 |
Offside Inner Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Rear fog lamp light intensity significantly reduced |4.5.4 |a|| | 1 |
Emissions not tested |8.2.2.2 |e|| | 1 |
Exhaust emissions likely to be affected by an exhaust leak Hole in centre silencer |8.2.2.1 |b|| | 1 |
Rear brake disc in such a condition that it is seriously weakened | 1 |
Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area. |6.1.B.2| | 1 |
Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area. |6.1.B.2| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Steering rack gaiter split |2.2.D.2d| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Rear fog lamp has less than 50% of the light sources illuminating |1.3.2b| | 1 |
Offside Rear Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
Centre Rear Stop lamp not working |1.2.1b| | 1 |
Power steering component|s| leaking |2.3.3b| | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Centre Exhaust system not adequately supported mount broken of system |7.1.1| | 1 |
Fuel pipe leaking |7.2.3| | 1 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
Offside Rear Stop lamp missing |1.2.1a| | 1 |
Offside Rear coil spring cracked |2.4.C.1a| | 1 |
Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Rear coil spring broken |2.4.C.1a| | 1 |
Nearside Rear Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Rear Parking brake efficiency below requirements BOTH SIDES (1.4.2 (a) (i)) | 1 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Rear Exhaust system not adequately supported |7.1.1| | 1 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Front Headlamps matched pair are incorrectly positioned |1.7.3| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
Offside Front Steering rack gaiter insecure |2.2.D.2d| | 1 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Nearside Front front brake juddering severely |3.7.A.2b| | 1 |
Offside front brake juddering severely |3.7.A.2b| | 1 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Mechanical brake component has restricted free movement | 1 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Slam panel (tow bar attached) (6.1.1 (c) (i)) | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Slam panel (tow bar attached) (6.1.1 (c) (i)) | 1 |
Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Obligatory mirror missing |8.1.1| | 1 |
Brake pedal spongy |3.3.B.1b| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill panel |5.3.6 |a| |i|| | 1 |
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Nearside Side repeater not working |4.4.1 |a| |ii|| | 1 |
Nearside Front Shock absorber insecure |2.7.2b| | 1 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Offside Front Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 1 |
Rear Prop shaft likely to become detached |6.1.7 |a| |ii|| | 1 |
Rear Prop shaft joint so worn it is likely to fail |6.1.7 |c| |ii|| | 1 |
Headlamps matched pair are not the same colour |1.7.6| | 1 |
Nearside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
Offside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near subframe |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill |5.3.6 |a| |i|| | 1 |
Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear Exhaust mounting missing |7.1.1b| | 1 |
Nearside Rear Rear reflector defective or damaged by more than 50% of the reflecting surface |4.8.1 |a| |ii|| | 1 |
Offside Rear Rear reflector defective or damaged by more than 50% of the reflecting surface |4.8.1 |a| |ii|| | 1 |
Offside Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
Nearside Front Suspension component mounting prescribed area is inadequately repaired Jacking point. (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Jacking point. (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill end. (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Obligatory mirror missing (3.3 (a)) | 1 |
Rear Exhaust has a major leak of exhaust gases Joint (6.1.2 (a)) | 1 |
Offside Rear reflector excessively damaged so that its function is impaired |1.5.1c| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded inner & outer sill |5.2.6| | 1 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Offside Front Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
Offside Rear Rear reflector reflecting white to the rear (4.8.2 (a) (ii)) | 1 |
Nearside Front All position lamps not working |1.1.A.3b| | 1 |
Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Rear fog lamp missing |1.3.2a| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member |6.1.1 |c| |i|| | 1 |
Rear fog lamp switch missing |1.3.1a| | 1 |
Rear Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement |2.4.B.2| | 1 |
Nearside Leaf spring has a deteriorated anchor pin rubber bush resulting in excessive movement |2.4.B.2| | 1 |
Nearside Rear Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 1 |
Offside Rear Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 1 |
Offside Front brake disc excessively pitted |3.5.1h| | 1 |
Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
Offside Rear Inner Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Nearside Rear Outer Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Fuel cap/sealing device missing |7.2.4a| | 1 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Emissions not tested not tested due to rear exhaust section detached from centre section (8.2.1.2 (d)) | 1 |
Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting hole in n/s/f inner sill (6.2.2 (d) (i)) | 1 |
Offside Front Body panel corroded and likely to cause injury arch (6.2.1 (a) (i)) | 1 |
Nearside Rear Lower Suspension arm pin or bush excessively worn trailing arm (5.3.4 (a) (i)) | 1 |
Offside Rear Lower Suspension arm pin or bush excessively worn trailing arm (5.3.4 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Brake performance not tested rear brakes binding (1.2.1 (g)) | 1 |
Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill |5.3.6 |a| |i|| | 1 |
Nearside Rear Outer Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Nearside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis |6.1.1 |c| |i|| | 1 |
Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis |6.1.1 |c| |i|| | 1 |
Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember |6.1.1 |c| |i|| | 1 |
Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced panel |6.1.1 |c| |i|| | 1 |
Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch |6.1.1 |c| |i|| | 1 |
Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch |6.1.1 |c| |i|| | 1 |
Nearside Rear Upper Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch |6.1.1 |c| |i|| | 1 |
Offside Rear Upper Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch |6.1.1 |c| |i|| | 1 |
Offside Rear Brake pivot has restricted free movement |3.5.1k| | 1 |
Nearside Rear Brake pivot has restricted free movement |3.5.1k| | 1 |
Rear fog lamp emits a light other than red (1.3.2e) | 1 |
Nearside Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Nearside Front Lower Suspension arm pin or bush excessively worn Wishbone (5.3.4 (a) (i)) | 1 |
Offside Front Lower Suspension arm pin or bush excessively worn Wishbone (5.3.4 (a) (i)) | 1 |
Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis by shock absorber mount (5.3.6 (a) (i)) | 1 |
Emissions not tested Due to oil leak (8.2.2.2 (e)) | 1 |
Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
Centre Exhaust system not adequately supported (7.1.1) | 1 |
Nearside Front Lower Suspension arm has excessive play in a ball joint (2.4.G.2) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
Offside Rear fog lamp insecure |1.3.2a| | 1 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded inner wheelarch |2.4.A.3| | 1 |
Offside Rear fog lamp missing |1.3.2a| | 1 |
Offside Rear Body has a projection caused by corrosion bumper |6.1.C.1| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Front brake application uneven | 1 |
Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Offside Outer Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
Seat belt missing nearside and offside rear seat belt stalks missing (7.1.2 (a)) | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear outer sill (5.3.6 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing at shock absorber mount (5.3.6 (a) (i)) | 1 |
Nearside Rear Towbar excessively corroded within 30cm of towbar mounting chqassis (6.1.6 (i) (i)) | 1 |
Offside Rear Towbar has excessive damage seriously affecting its strength within 30cm of a towbar mounting chassis leg (6.1.6 (i) (i)) | 1 |
Nearside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Offside Front Suspension spring mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear brake disc excessively pitted |3.5.1h| | 1 |
Offside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
Offside Inner Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Parking brake: efficiency below requirements |3.7.B.7| | 1 |
Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Nearside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Windscreen has damage | 1 |
Nearside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded body to chassis mount |2.4.A.3| | 1 |
Brake valve leaking |3.6.A.1| | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded centre |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded centre |2.4.A.3| | 1 |
Nearside Front Brake pipe leaking |3.6.A.1| | 1 |
Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 1 |
Service brake: efficiency below requirements |3.7.B.7| | 1 |
Offside Front coil spring incomplete |2.4.C.1a| | 1 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
All position lamps not working |1.1.A.3b| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner sill & front outrigger @ suspensionarm mounting |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner sill & outrigger @ suspension arm mounting |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded Inner sill @ inner wing |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill & inner wing |2.4.A.3| | 1 |
Brake hose excessively deteriorated | 1 |
Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt gaitor burst (5.3.4 (b) (ii)) | 1 |
Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Brake lever has insufficient reserve travel park brake (1.1.2 (a)) | 1 |
Nearside Front Anti-roll bar linkage ball joint excessively worn drop link (5.3.4 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outrigger. (5.3.6 (a) (i)) | 1 |
Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Offside and nearside rear at tow bar mounts. (6.1.1 (c) (i)) | 1 |
Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Rear fog lamp tell tale not working |1.3.1b| | 1 |
Central Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 1 |