| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 47 |
| Headlamp aim out of alignment | 27 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 23 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 18 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 15 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 14 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 13 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 12 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 12 |
| Registration plate lamp issues | 12 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 11 |
| Emissions not tested (8.2.1.2 (d)) | 11 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 11 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 10 |
| Windscreen washer not working | 10 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 9 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 9 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 8 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 7 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 7 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 6 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 6 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 6 |
| Nearside Rear Shock absorbers has a serious fluid leak | 5 |
| Anti-lock braking system warning lamp indicates an ABS fault | 5 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 5 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 5 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 4 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
| Registration plate issues | 4 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 4 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 4 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 4 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 3 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 3 |
| Rear fog lamp missing |1.3.2a| | 3 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 3 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 3 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Horn not working (7.7 (a)) | 3 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 2 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Anti-lock braking system warning lamp does not illuminate (1.6 (a)) | 2 |
| Nearside Rear Seat belt buckle missing (7.1.2 (d)) | 2 |
| Offside Rear Seat belt buckle missing (7.1.2 (d)) | 2 |
| Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Rear Shock absorbers has a serious fluid leak | 2 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Rear Passengers seat backrest cannot be secured in the upright position. (6.2.6 (a) (i)) | 2 |
| Nearside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 2 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Offside Front Position lamp not working |4.2.1 |a|| | 2 |
| Front brake disc in such a condition that it is seriously weakened | 2 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 2 |
| Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 2 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Oil leaking excessively from transmission (8.4.1 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Rear Lower Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 2 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 2 |
| Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 2 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Brake pipe excessively corroded | 2 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Headlamp not working on dipped beam x2 (4.1.1 (a) (ii)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Headlamp lens seriously defective both front (4.1.1 (b) (ii)) | 1 |
| Nearside Front Seat belt anchorage loose (7.1.1 (b)) | 1 |
| Parking (secondary brake) on a single line braking system grabbing severely (1.3.1 (c)) | 1 |
| Nearside Rear Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Offside Rear Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 1 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Outer Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Position lamp not working all (4.2.1 (a) (ii)) | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a) (ii)) | 1 |
| Nearside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Rear fog lamp lens defective such that emitted light is adversely affected white light showing to rear (4.5.1 (b) (ii)) | 1 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Central Exhaust system insecure (6.1.2 (a)) | 1 |
| Rear Exhaust system insecure Fouling rear axle stabiliser bar (6.1.2 (a)) | 1 |
| Central Exhaust system insecure Foulinghandbrakecable (6.1.2 (a)) | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone A (8.3.1e) | 1 |
| Fuel cap/sealing device missing (7.2.4a) | 1 |
| Offside Front Body component damaged and likely to cause injury lamp (6.2.1 (a) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect NEARSIDE AND OFFSIDE HEADLAMP LENSES EFFECTING BEAM IMAGE (4.1.2 (c)) | 1 |
| Headlamp lens seriously defective EFFECTING BEAM IMAGE (4.1.1 (b) (ii)) | 1 |
| Offside Rear Rear fog lamp not working SIGNS OF WATER INGRESS IN LAMP AND NOT SECURELY FITTED (4.5.1 (a) (ii)) | 1 |
| Rear Body component damaged and likely to cause injury TAILE GATE MIRROR SNAPED OFF BRACKET HAS SHARP EDGES (6.2.1 (a) (i)) | 1 |
| Offside Rear Body component damaged and likely to cause injury lamp (6.2.1 (a) (i)) | 1 |
| Lower Steering column universal joint has excessive wear or play (2.2.2 (c)) | 1 |
| Nearside Front position lamp(s) not working (1.1.A.3b) | 1 |
| Offside Rear Body has a sharp edge caused by damage light lens (6.1.C.1) | 1 |
| Statutory seat belt missing middle row of seats centre seat belt stalk missing (5.1.1) | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Passengers seat insecure center row seat unit (6.2.6 (a) (ii)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 1 |
| Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt both |2.4.G.2| | 1 |
| Rear Statutory seat belt missing seats |5.1.1| | 1 |
| Nearside Front Tie bar/rod ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Tie bar/rod ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Position lamp switch does not illuminate the front and rear position lamps with a single operation (4.2.2 (a)) | 1 |
| Nearside Front Side repeater incorrect colour WHITE (4.4.3 (a)) | 1 |
| Offside Front Side repeater incorrect colour WHITE (4.4.3 (a)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light Showing white light to the rear. (4.5.4 (a)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect X2 (4.1.2 (c)) | 1 |
| Front Headlamp lens seriously defective X2 NSF/OSF MACHINE POLISH LENS. (4.1.1 (b) (ii)) | 1 |
| Offside Rear Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
| Offside Rear Seat belt missing Unable to see or Check behind Bed Possibly. (7.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill x2 (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt missing stalk (7.1.2 (a)) | 1 |
| Offside Rear Seat belt missing stalk (7.1.2 (a)) | 1 |
| Nearside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Offside Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Emissions not tested due to grill fitted in tail pipe (8.2.1.2 (d)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill x2 (5.3.6 (a) (i)) | 1 |
| Nearside Stop lamp(s) not working 380 bulb replaced (4.3.1 (a) (ii)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill - hole |6.2.2 |d| |i|| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill - hole |6.2.2 |d| |i|| | 1 |
| Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Offside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 1 |
| Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Offside Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction phone holder |3.1 |a| |ii|| | 1 |
| Rear Stop lamp not working both |1.2.1b| | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Offside Rear Position lamp not working |4.2.1 |a| |ii|| | 1 |
| Nearside Headlamp light intensity severely reduced lense opaque (4.1.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced lense opaque (4.1.4 (a)) | 1 |
| Windscreen wiper not working (3.4 (a)) | 1 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Fuel hose leaking (6.1.3 (b) (i)) | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Seat belt not functioning as intended seat belt trapped within seat (7.1.2 (c)) | 1 |
| Central Exhaust has a major leak of exhaust gases box (6.1.2 (a)) | 1 |
| Nearside Obligatory mirror insecure (3.3 (b) (ii)) | 1 |
| Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Emissions not tested Lambda reading excessive. Test aborted to avoid excessive engine revving. (8.2.1.2 (d)) | 1 |
| Nearside Front Headlamp lens seriously defective unable to produce clear beam pattern (4.1.1 (b) (ii)) | 1 |
| Offside Front Headlamp lens seriously defective unable to produce clear beam pattern (4.1.1 (b) (ii)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Exhaust has a major leak of exhaust gases exhaust flexi burst (6.1.2 (a)) | 1 |
| Emissions not tested due to burst exhaust (8.2.1.2 (d)) | 1 |
| Emissions not tested due to exhaust leek (8.2.1.2 (d)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill / outer sill /inner arch area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired inner sill repair not fully seam welded (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch sill area (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill /step area (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner sill /step area (5.3.6 (a) (i)) | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp lens seriously defective No beam pattern (4.1.1 (b) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Suspension arm mounting (5.3.6 (a) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases flexi pipe (6.1.2 (a)) | 1 |
| Nearside Rear Outer Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Headlamp light intensity severely reduced dip (4.1.4 (a)) | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer (6.1.2 (a)) | 1 |
| Emissions not tested due to exhaust gasleak (8.2.1.2 (d)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Headlamp light intensity severely reduced both need polishing (4.1.4 (a)) | 1 |
| Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Body component damaged and likely to cause injury lamp unit (6.2.1 (a) (i)) | 1 |
| Offside Rear Stop lamp(s) not working water in lamp unit (4.3.1 (a) (ii)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases exhaust backbox snapped off (6.1.2 (a)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill and outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Headlamp aim not tested no pattern (4.1.2 (b)) | 1 |
| Offside Front Headlamp aim not tested no pattern (4.1.2 (b)) | 1 |
| Offside Front Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits unable to maintain co fluctuates between 1079-286 constantly
emissons not tested (8.2.1.2 (b)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Horn not working |1.6.2a| | 1 |
| Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Battery insecure |1.9.1| | 1 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Headlamp aim projected beam image is obviously incorrect both no patterns (4.1.2 (c)) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Spare wheel carrier insecure (6.1.5 (a)) | 1 |
| Rear Bumper damaged and likely to cause injury when grazed or contacted sharp edges (6.1.4 (a) (i)) | 1 |
| Oil leaking excessively from engine engine (8.4.1 (a) (i)) | 1 |
| Offside Front Body has a sharp edge caused by damage fog light |6.1.C.1| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Anti-roll bar linkage ball joint excessively worn both front (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 1 |
| Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt missing (7.1.2 (a)) | 1 |
| Offside Rear Seat belt missing (7.1.2 (a)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rearmost mount (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rearmost mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Rear brake disc in such a condition that it is seriously weakened | 1 |
| Rear Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Steering column universal joint has excessive wear or play lower uj, to rack (2.2.2 (c)) | 1 |
| Emissions not tested due to major exhaust leak (8.2.1.2 (d)) | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush |5.3.4 |a| |i|| | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn D bush |5.3.4 |a| |i|| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Rear Seat belt buckle missing (7.1.2 (d)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Offside Stop lamp(s) emits other than a steady red light showing white (4.3.3 (a) (ii)) | 1 |
| Offside Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect both sides (4.1.2 (c)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting boot floor (6.1.6 (i) (i)) | 1 |
| Nearside Front Headlamp incorrect colour different bulb (4.1.4 (a)) | 1 |
| Offside Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Front Headlamp lens seriously defective cleaned during test (4.1.1 (b) (ii)) | 1 |
| Offside Front Headlamp lens seriously defective cleaned during test (4.1.1 (b) (ii)) | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Rear Anti-roll bar pin or bush excessively worn Both rear D-bushes (5.3.4 (a) (i)) | 1 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Headlamp does not operate immediately when selected on dipped beam dims off |1.7.4a| | 1 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Headlamp aim projected beam image is obviously incorrect Both (4.1.2 (c)) | 1 |
| Nearside Rear Outer Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Outer Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Inner Anti-roll bar pin or bush excessively worn Both (5.3.4 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Anti-lock braking system warning lamp does not illuminate (3.4.1b) | 1 |
| Nearside Front position lamp(s) excessively deteriorated so that it is not visible from a reasonable distance (1.1.A.3d) | 1 |
| Offside Front position lamp(s) excessively damaged so that it is not visible from a reasonable distance (1.1.A.3d) | 1 |
| Headlamp aim projected beam image is obviously incorrect Both front (4.1.2 (c)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced and outer sill (7.1.1 (a) (i)) | 1 |
| Horn sound not in accordance with requirements (7.7 (c)) | 1 |
| Offside Rear Lower Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Rear fog lamp switch inoperative Not illuminating (4.5.3 (a)) | 1 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
| Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Front and middle inner sill. (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Middle and rear inner sill. (6.2.2 (d) (i)) | 1 |
| Offside Rear Position lamp with a multiple light source more than 1/2 not functioning (4.2.1 (a) (ii)) | 1 |
| Anti-roll bar pin or bush excessively worn Both rear inner bushes (5.3.4 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill x 2 (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill x 2 (6.1.1 (c) (i)) | 1 |
| Headlamp aim not tested (4.1.2 (b)) | 1 |
| Rear fog lamp switch missing |1.3.1a| | 1 |
| Rear fog lamp tell tale missing |1.3.1b| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Position lamp not working Side light (4.2.1 (a) (ii)) | 1 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle internal handle in op (6.2.3 (a)) | 1 |
| Central Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 1 |
| Emissions not tested CO reading too eratic. (8.2.1.2 (d)) | 1 |
| Nearside Front Tie bar/rod ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt track rod end split |2.4.G.2| | 1 |
| Offside Front Tie bar/rod ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt track rod end split |2.4.G.2| | 1 |