| Most common failures | No# failures |
|---|
| Rear fog lamp not working (4.5.1 (a) (ii)) | 15 |
| Windscreen wiper does not clear the windscreen effectively | 14 |
| Headlamp aim out of alignment | 11 |
| Windscreen washer not working | 8 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 7 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 7 |
| Horn not working (7.7 (a)) | 7 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 6 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 4 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 4 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Anti-lock braking system warning lamp indicates an ABS fault | 3 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 3 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Brake pipe excessively corroded | 3 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Seat belt buckle missing (7.1.2 (d)) | 2 |
| Offside Rear Seat belt buckle missing (7.1.2 (d)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Cross member (5.3.6 (a) (i)) | 2 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
| Brakes imbalanced across an axle | 2 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 2 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 2 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Offside Front Shock absorbers has a serious fluid leak | 2 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Registration plate issues | 2 |
| Registration plate lamp issues | 2 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 2 |
| Nearside Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Rear fog lamp obviously incorrectly positioned (4.5.4 (a)) | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis next to suspension arm mounting (5.3.6 (a) (i)) | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front crossmember (5.3.6 (a) (i)) | 1 |
| Fuel system component leaking fuel pump (6.1.3 (b) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUT RIGGER (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUT RIGGER (5.3.6 (a) (i)) | 1 |
| Rear Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Offside Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced floor to sill (7.1.1 (a) (i)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Steering locking device missing track rod end split pin (2.1.3 (d)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt both sides (5.3.4 (b) (ii)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front inner sills both sides (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Front Anti-roll bar linkage damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Front Anti-roll bar linkage damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Cross member (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Front Headlamp light intensity severely reduced both heavily uv/sun damaged (4.1.4 (a)) | 1 |
| Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Brake disc contaminated (1.1.14 (b)) | 1 |
| Offside Rear Brake disc contaminated (1.1.14 (b)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt missing belt (7.1.2 (a)) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner seal chalked (6.1.1 (c) (i)) | 1 |
| Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Rear Reversing lamp inoperative (4.6.1 (a)) | 1 |
| Offside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Rear Lower Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
| Central Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Electrical wiring likely to touch hot or rotating parts (4.11 (a) (iii)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Exhaust emissions exceed default limit of 0.7m-1 (8.2.2.2 (b)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Brake disc significantly and obviously worn inner edge (1.1.14 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced lower step (6.1.1 (c) (i)) | 1 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced of inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Fuel cap/sealing device ineffective temp fuel cap fitted (6.1.3 (b) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front cossmember (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear fog lamp does not emit a steady red light showing white (4.5.4 (a)) | 1 |
| Exhaust has a major leak of exhaust gases major exhaust leak/downpipe next to the manifold (6.1.2 (a)) | 1 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed and corroded (5.3.6 (a) (i)) | 1 |
| Suspension arm ball joint excessively worn both front lower (5.3.4 (a) (i)) | 1 |
| Central Rear Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases flexi pipe joint (6.1.2 (a)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt upper boot (5.3.4 (b) (ii)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength coil spring mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill under vehicle (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength door step under vehicle (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength door step under vehicle (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt missing boot seat (7.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill area (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting missing (5.3.3 (a) (ii)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Rear Other passenger door cannot be opened from outside the vehicle Sliding door. (6.2.3 (a)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill and inner arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Rear Steering component mounting prescribed area is excessively corroded sill (2.1.2 (e) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Steering component mounting prescribed area is excessively corroded sill (2.1.2 (e) (i)) | 1 |
| Offside Front Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases flexi joint (6.1.2 (a)) | 1 |
| Offside Front Suspension arm insecurely attached bolt (5.3.3 (a) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2) | 1 |
| Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Offside Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush (2.4.G.2) | 1 |
| Offside Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OUTER SILL (5.3.6 (a) (i)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength valance holed (5.3.6 (a) (i)) | 1 |
| Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 1 |
| Rear Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 1 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases section missing (6.1.2 (a)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Back box holded (6.1.2 (a)) | 1 |
| Electrical wiring insulation so damaged or deteriorated it is likely to cause a short-circuit Battery terminals (4.11 (c) (ii)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis (6.1.1 (c) (i)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury Wheel Arch (6.2.1 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis (6.1.1 (c) (i)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury Wheel Arch (6.2.1 (a) (i)) | 1 |
| Rear Vehicle structure excessively corroded within 30cm of towbar mounting Cross Member (6.1.6 (i) (i)) | 1 |
| Nearside Front Inner Macpherson strut mounting corroded and seriously weakened wheel arch (5.3.3 (b) (i)) | 1 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill area (7.1.1 (a) (i)) | 1 |
| Offside Headlamp lens seriously defective No pattern (4.1.1 (b) (ii)) | 1 |
| Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Shock absorber mount area (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Track rod end ball joint dust cover missing (2.1.3 (g) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases flexi area (6.1.2 (a)) | 1 |
| Exhaust system insecure hanger snapped (6.1.2 (a)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced centre, outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Headlamp lens seriously defective both unclear. (4.1.1 (b) (ii)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Fuel cap/sealing device missing |7.2.4a| | 1 |
| Battery insecure |1.9.1| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Front Headlamp aim projected beam image is obviously incorrect both front (4.1.2 (c)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill multiple locations (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill multiple locations (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill chassis front and centre (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill chassis front centre and rear (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength cross member ex corrosion. within 30cm of subframe mount. (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength front crosssmember ex corrosion within 30cm of subframe mouning. (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Rear Vehicle structure excessively corroded within 30cm of towbar mounting x member (6.1.6 (i) (i)) | 1 |
| Nearside Rear All position lamps not working |1.1.A.3b| | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Rear fog lamp switch inoperative |4.5.3 |a| |ii|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |