Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 24 |
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 16 |
Headlamp aim out of alignment | 16 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 15 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 15 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 14 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 12 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 12 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 12 |
Emissions not tested (8.2.1.2 (d)) | 9 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 8 |
Registration plate lamp issues | 8 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 7 |
Anti-lock braking system warning lamp indicates an ABS fault | 7 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 7 |
Windscreen washer not working | 6 |
Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 5 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 5 |
Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 5 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 5 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 5 |
Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 5 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
Brakes imbalanced across an axle | 5 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
Offside Rear Shock absorbers has a serious fluid leak | 4 |
Horn not working (7.7 (a)) | 4 |
Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
Rear fog lamp not working |1.3.2b| | 4 |
Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
Offside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
Brake pipe excessively corroded | 4 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 3 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 3 |
Registration plate issues | 3 |
Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 3 |
Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 3 |
Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 3 |
Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
Front brake disc in such a condition that it is seriously weakened | 3 |
Nearside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
Offside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 3 |
Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 3 |
Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
Rear Anti-roll bar pin or bush excessively worn D bushes (5.3.4 (a) (i)) | 2 |
Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
Power steering malfunctioning (2.1.5 (a)) | 2 |
Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Brake lever has insufficient reserve travel (1.1.2 (a)) | 2 |
Fuel cap/sealing device missing (6.1.3 (b) (i)) | 2 |
Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
Offside Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 2 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
Exhaust carbon monoxide content at idle exceeds default limits see emissions printout (8.2.1.2 (b)) | 2 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
Position lamp not working ALL (4.2.1 (a) (ii)) | 2 |
Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 2 |
Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 2 |
Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 2 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Rear Exhaust has a major leak of exhaust gases flex joint (6.1.2 (a)) | 2 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 2 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
Offside Rear Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 2 |
Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 2 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 2 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength of the sill holed within 30cm of front suspension (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength of the sill holed within 30cm of rear suspension (5.3.6 (a) (i)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength of the sill holed withing 30cm of front suspension (5.3.6 (a) (i)) | 1 |
Central Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced of the sill holed below seat/ seatbelt area. (7.1.1 (a) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill / outrigger corroded (6.1.1 (c) (i)) | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect deteriorated (4.1.2 (c)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area and front cross member (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength end of sill (5.3.6 (a) (i)) | 1 |
Offside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
Emissions not tested over heating (8.2.1.2 (d)) | 1 |
Steering system excessively rough (2.1.1 (a)) | 1 |
Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within jacking point (6.1.1 (c) (i)) | 1 |
Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within seat belt anchor (6.1.1 (c) (i)) | 1 |
Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within suspension mounting (6.1.1 (c) (i)) | 1 |
Nearside Front Anti-roll bar linkage ball joint excessively worn drop link (5.3.4 (a) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within the jacking point (6.1.1 (c) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within the seat belt anchor (6.1.1 (c) (i)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within the suspension mounting (6.1.1 (c) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner chassis (5.3.6 (a) (i)) | 1 |
Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis out rigger (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis out rigger (5.3.6 (a) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
Offside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases Flexi (6.1.2 (a)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis outrigger (5.3.6 (a) (i)) | 1 |
Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Oil leaking excessively from transmission Auto box cooler pipe (8.4.1 (a) (i)) | 1 |
Nearside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill by door step (6.1.1 (c) (i)) | 1 |
Nearside Rear Seat belt buckle missing centre seat (7.1.2 (d)) | 1 |
Central Rear Passengers seat insecure insecure on frame (6.2.6 (a) (ii)) | 1 |
Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt both sides x2 (2.1.3 (g) (ii)) | 1 |
Hazard warning switch inoperative (4.4.2 (a) (ii)) | 1 |
Exhaust hydrocarbon content after 2nd fast idle exceeds default limits see emissions printout (8.2.1.2 (b)) | 1 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits see emissions printout (8.2.1.2 (b)) | 1 |
Exhaust Lambda reading after 2nd fast idle outside specified limits see emissions printout (8.2.1.2 (c)) | 1 |
Nearside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Headlamp insecure (4.1.1 (c)) | 1 |
Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced centre inner sill (6.1.1 (c) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill area - Chalked (5.3.6 (a) (i)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill holed (6.2.2 (d) (i)) | 1 |
Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill inner holed (6.2.2 (d) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill holed (6.2.2 (d) (i)) | 1 |
Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill holed marked up in yellow (6.2.2 (d) (i)) | 1 |
Rear fog lamp does not emit a steady red light bulb faded (4.5.4 (a)) | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced lower inner wheel arch (7.1.1 (a) (i)) | 1 |
Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases rear box (6.1.2 (a)) | 1 |
Rear brake disc in such a condition that it is seriously weakened | 1 |
Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill panel (5.3.6 (a) (i)) | 1 |
Nearside Rear Position lamp has a product on the lens or light source which shows white light to the rear lamp broken (4.2.3 (b) (ii)) | 1 |
Exhaust has a major leak of exhaust gases flexi joint (6.1.2 (a)) | 1 |
Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 1 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Offside Stop lamp not working |1.2.1b| | 1 |
Central Exhaust has a major leak of exhaust gases flexy (6.1.2 (a)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Crossmember (5.3.6 (a) (i)) | 1 |
Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded (7.1.1 (a) (i)) | 1 |
Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
Offside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
Emissions not tested exhaust leak (8.2.1.2 (d)) | 1 |
Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Rear Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
Offside Rear Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
Nearside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
Headlamp not working on dipped beam both (4.1.1 (a) (ii)) | 1 |
Nearside Rear Seat belt missing (7.1.2 (a)) | 1 |
Fuel system component leaking engine area (6.1.3 (b) (i)) | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corroded and holed within 30cm of suspension mounting (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corroded and holed within 30cm of suspension mouonting (5.3.6 (a) (i)) | 1 |
Rear fog lamp switch missing (4.5.3 (a)) | 1 |
Rear Exhaust silencer insecure (8.1.1 (b) (i)) | 1 |
Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
Oil leaking continuously from engine posing a serious risk to road safety (8.4.1 (a) (ii)) | 1 |
Nearside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
Offside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
Offside Front Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
Brake hydraulic reservoir cap missing (1.1.10 (e)) | 1 |
Emissions not tested Due to over heating (8.2.1.2 (d)) | 1 |
Offside Rear Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
Nearside Rear Anti-roll bar linkage damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
Nearside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 1 |
Nearside Lower Front suspension ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Lower Front suspension ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Body panel corroded and likely to cause injury Wheel arch (6.2.1 (a) (i)) | 1 |
Body component damaged and likely to cause injury Front bumper (6.2.1 (a) (i)) | 1 |
Headlamp has a product on the lens so that the light output is severely reduced nearside and offside (4.1.4 (b)) | 1 |
Exhaust has a major leak of exhaust gases rear silencer missing (6.1.2 (a)) | 1 |
Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Headlamp light intensity severely reduced |4.1.4 |a|| | 1 |
Offside Front Headlamp light intensity severely reduced |4.1.4 |a|| | 1 |
Offside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
Nearside Rear Valve stem seriously damaged |4.1.D.1e| | 1 |
Battery insecure |1.9.1| | 1 |
Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 1 |
Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 1 |
Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Nearside Headlamp are incorrectly positioned (4.1.4 (a)) | 1 |
Offside Headlamp are incorrectly positioned (4.1.4 (a)) | 1 |
Front Headlamp aim projected beam image is obviously incorrect both sides deteriorated (4.1.2 (c)) | 1 |
Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced panel corner behind bumper (6.1.1 (c) (i)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end area (5.3.6 (a) (i)) | 1 |
Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area (5.3.6 (a) (i)) | 1 |
Front Bumper likely to become detached (6.1.4 (a) (ii)) | 1 |
Offside Rear Outer Integral body structure is fractured and structural rigidity is significantly reduced sill holed (6.1.1 (a) (i)) | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
Central Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Rear Seat belt missing corresponding seat missing no buckle (7.1.2 (a)) | 1 |
Offside Rear Seat belt missing corresponding seat missing no buckle (7.1.2 (a)) | 1 |
Nearside Integral body structure is fractured and structural rigidity is significantly reduced sill end/ inner wheel arch (6.1.1 (a) (i)) | 1 |
Front Lower Suspension component mounting prescribed area fractured significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
Nearside Inner Integral body structure is fractured and structural rigidity is significantly reduced sill in the middle (6.1.1 (a) (i)) | 1 |
Offside Rear Inner Integral body structure is fractured and structural rigidity is significantly reduced sill (6.1.1 (a) (i)) | 1 |
Offside Rear Integral body structure is fractured and structural rigidity is significantly reduced sill end (6.1.1 (a) (i)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength wheel arch behind wheel (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength wheel arch behind wheel (5.3.6 (a) (i)) | 1 |
Headlamp lens seriously defective Both (4.1.1 (b) (ii)) | 1 |
Headlamp aim projected beam image is obviously incorrect Both (4.1.2 (c)) | 1 |
Position lamp light intensity significantly reduced Both front (4.2.3 (a) (ii)) | 1 |
Central Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced x member (7.1.1 (a) (i)) | 1 |
Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Out rigger (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Out rigger (5.3.6 (a) (i)) | 1 |
Nearside Front Outer Anti-roll bar ball joint excessively worn Drop link (5.3.4 (a) (i)) | 1 |
Offside Rear fog lamp does not face the rear (4.5.4 (a)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower arm mounting (5.3.6 (a) (i)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Rear Bumper insecure bumper ends (6.1.4 (a) (i)) | 1 |
Oil leaking excessively from transmission (8.4.1 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases centre section (6.1.2 (a)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Forward Wheel Arch (5.3.6 (a) (i)) | 1 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel Arch (7.1.1 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill (7.1.1 (a) (i)) | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Arch (7.1.1 (a) (i)) | 1 |
Nearside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
Rear fog lamp switch not operating in accordance with the requirements does not ilimunate (4.5.3 (a)) | 1 |
Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
Rear Exhaust has a major leak of exhaust gases hole in silencer (6.1.2 (a)) | 1 |
Front Headlamp lens seriously defective both sides deteriorated (4.1.1 (b) (ii)) | 1 |
Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Emissions not tested unable to keep a steady rpm, co high (8.2.1.2 (d)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill, inner sill corroded (5.3.6 (a) (i)) | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Rear Seat belt buckle missing Rearmost (7.1.2 (d)) | 1 |
Offside Rear Seat belt buckle missing Rearmost (7.1.2 (d)) | 1 |
Undertray likely to become detached (6.2.1 (a) (ii)) | 1 |
Central Exhaust has a major leak of exhaust gases joint (6.1.2 (a)) | 1 |
Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Emissions not tested Exhaust rear end major leak (8.2.1.2 (d)) | 1 |
Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill excessively corrode within 30cm of trailing arm mounting (5.3.6 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases flexi exhaust pipe (6.1.2 (a)) | 1 |