| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 30 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 19 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 15 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 15 |
| Windscreen washer not working | 10 |
| Anti-lock braking system warning lamp indicates an ABS fault | 10 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Headlamp aim out of alignment | 8 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 6 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 6 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 5 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 5 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 5 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 4 |
| Emissions not tested (8.2.1.2 (d)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Registration plate lamp issues | 4 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Nearside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 3 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 3 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 3 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 3 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 2 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 2 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 2 |
| Anti-lock braking system warning lamp does not illuminate (1.6 (a)) | 2 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 2 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 2 |
| Headlamp light intensity severely reduced both (4.1.4 (a)) | 2 |
| Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting crossmember inner arch area (6.1.6 (i) (i)) | 1 |
| Undertray likely to become detached (6.2.1 (a) (ii)) | 1 |
| Offside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced inner sill to front suspension mounting strengthening plate is badly corroded and holed (6.1.1 (b) (ii)) | 1 |
| Offside Front Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced inner sill to front suspension mounting strengthening plate is badly corroded and holed (6.1.1 (b) (ii)) | 1 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Nearside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill. (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength anti -roll bar mounting. (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension arm / rear mounting. (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer mounting. (7.1.1 (a) (i)) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Brake hydraulic reservoir cap missing (1.1.10 (e)) | 1 |
| Emissions not tested blue smoke (8.2.1.2 (d)) | 1 |
| Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch where it meets sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Offside Rear Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Emissions not tested vehicle temp gauge showed signs of engine over heating before catalytic test was carried out (8.2.1.2 (d)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Front Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Rear fog lamp lens defective such that emitted light is adversely affected lens is pink (4.5.1 (b) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases Silencer (6.1.2 (a)) | 1 |
| Central Rear Exhaust emissions likely to be affected by an exhaust leak Silencer (8.2.1.1 (b)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member (6.1.1 (c) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is inadequately repaired sill fiberglass (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch (5.3.6 (a) (i)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both front inner sills (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced NS + OS (4.1.4 (b)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill x2 (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill x2 (7.1.1 (a) (i)) | 1 |
| Headlamp light intensity severely reduced NS + OS (4.1.4 (a)) | 1 |
| Hazard warning switch inoperative remain on not flashing (4.4.2 (a) (ii)) | 1 |
| All direction indicators not working remain on not flashing (4.4.1 (a) (ii)) | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Nearside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced box section by mount (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear inner wing (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Central Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under radiator (5.3.6 (a) (i)) | 1 |
| Stop lamp(s) all not working and high level one only 50% (4.3.1 (a) (iii)) | 1 |
| Central Exhaust silencer insecure (8.1.1 (b) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Vehicle structure inadequately repaired such that structural rigidity is significantly reduced sill not seam welded (6.1.1 (d) (i)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Flexi (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength In arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength In arch (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect no patten (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect no patten (4.1.2 (c)) | 1 |
| Exhaust has a major leak of exhaust gases Flexi-pipe (6.1.2 (a)) | 1 |
| Emissions not tested Excessive exhaust leak (8.2.1.2 (d)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Emissions not tested Duie to major exhaust leak (8.2.1.2 (d)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced Both front headlights are cloudy (4.1.4 (b)) | 1 |
| Vehicle structure is fractured and structural rigidity is significantly reduced O/S/R chassis sill rusty and holed (6.1.1 (a) (i)) | 1 |
| Offside Front Outer Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger to inner sill (5.3.6 (a) (i)) | 1 |
| Rear Brake lining(s) less than 1.5 mm thick (1.1.13 (a) (ii)) | 1 |
| Nearside Front Outer Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering SEAL (6.1.1 (c) (ii)) | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering SEAL (6.1.1 (c) (ii)) | 1 |
| Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected under body sill (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected under body sill (5.3.6 (a) (ii)) | 1 |
| Nearside Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Offside Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Position lamp has a product on the lens or light source which shows white light to the rear (4.2.3 (b) (ii)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect both sides (4.1.2 (c)) | 1 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Nearside Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Nearside Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 1 |
| Nearside Front Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Nearside Front Headlamp light source and lamp not compatible hid kit fitted (4.1.4 (c)) | 1 |
| Offside Front Headlamp light source and lamp not compatible hid kit fitted (4.1.4 (c)) | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting front to rear sills (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sills (6.2.2 (d) (i)) | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering crossmember (6.1.1 (c) (ii)) | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury Wheel arch (6.2.1 (a) (i)) | 1 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear fog lamp tell tale not working (1.3.1b) | 1 |
| Rear fog lamp not working (1.3.2b) | 1 |
| Offside Rear Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Emissions not tested Due to the engine misfiring (8.2.1.2 (d)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced corner panel (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Central Seat belt missing row of seats buckles missing (7.1.2 (a)) | 1 |
| Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Rear Upper Stop lamp(s) with a multiple light source more than 1/2 not functioning (4.3.1 (a) (ii)) | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Brake pipe excessively corroded | 1 |
| Offside Rear Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/out rigger (5.3.6 (a) (i)) | 1 |
| Nearside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Front Inner Integral body structure is fractured and structural rigidity is significantly reduced sill, marked in yellow (6.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure is fractured and structural rigidity is significantly reduced sill, marked in yellow (6.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure is fractured and structural rigidity is significantly reduced sill, marked in yellow, axle mounting (6.1.1 (a) (i)) | 1 |
| Offside Rear Inner Integral body structure is fractured and structural rigidity is significantly reduced sill, marked in yellow, axle mounting (6.1.1 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases flexi pipe (6.1.2 (a)) | 1 |
| Emissions not tested due to major exhaust leak (8.2.1.2 (d)) | 1 |
| Fuel system component leaking filter (6.1.3 (b) (i)) | 1 |
| Registration plate issues | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Steering linkage ball joint has excessive play (Drumstick) (2.1.3 (b) (i)) | 1 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Central Rear Seat belt buckle missing (7.1.2 (d)) | 1 |
| Rear fog lamp obviously incorrectly positioned (4.5.4 (a)) | 1 |
| Brakes imbalanced across an axle | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light pink-white ish (4.5.4 (a)) | 1 |
| Nearside Front Headlamp has a product on the light source so that the light output is severely reduced blurry headlamp (4.1.4 (b)) | 1 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced blurry headlamp (4.1.4 (b)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer upper sill corroded and holed, it is in 30 cm prescribed are for NSR suspension arm mounting point. (5.3.6 (a) (i)) | 1 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |