| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 79 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 41 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 40 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 35 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 34 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 27 |
| Anti-lock braking system warning lamp indicates an ABS fault | 26 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 21 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 21 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 20 |
| Registration plate lamp issues | 19 |
| Headlamp aim out of alignment | 16 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 15 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 14 |
| Windscreen washer not working | 13 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 13 |
| Brake pipe excessively corroded | 13 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 12 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 12 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 11 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 11 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 11 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 10 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 10 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 10 |
| Emissions not tested (8.2.1.2 (d)) | 10 |
| Horn not working (7.7 (a)) | 10 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 9 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 9 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 9 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 8 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 8 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 8 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 8 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 8 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Emissions unable to be completed (8.2.1.2 (d)) | 8 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 7 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 7 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 7 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 7 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 7 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 7 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 7 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 7 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 7 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 6 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 6 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 6 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 6 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 6 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 6 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 6 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 5 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 5 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 5 |
| Brakes imbalanced across an axle | 5 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 5 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 5 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 5 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 5 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 5 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 4 |
| Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 4 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 4 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 4 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 4 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 4 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 4 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 4 |
| Offside Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 4 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Offside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 4 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 4 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 3 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 3 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 3 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 3 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 3 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 3 |
| Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 3 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 3 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 3 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 3 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
| Offside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 2 |
| Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 2 |
| Anti-lock braking system warning lamp does not illuminate (1.6 (a)) | 2 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Emissions not tested (8.2.2.2 (e)) | 2 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Rear Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 2 |
| Headlamp aim not tested (4.1.2 (b)) | 2 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 2 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 2 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Reversing lamp inoperative (4.6.1 (a)) | 2 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 2 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 2 |
| Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Brake performance unable to be tested (1.2.1 (g)) | 2 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch and inner chassis (5.3.6 (a) (i)) | 2 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 2 |
| Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 2 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 2 |
| Registration plate issues | 2 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn d bush (5.3.4 (a) (i)) | 2 |
| Offside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |