| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 16 |
| Windscreen wiper does not clear the windscreen effectively | 16 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 15 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 14 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 13 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 10 |
| Anti-lock braking system warning lamp indicates an ABS fault | 9 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 9 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 5 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 5 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 4 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 4 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
| Windscreen washer not working | 4 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Emissions unable to be completed (8.2.1.2 (d)) | 3 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 3 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 3 |
| Rear brake disc in such a condition that it is seriously weakened | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 3 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Rear fog lamp tell tale missing |1.3.1b| | 2 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 2 |
| Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 2 |
| Fuel system component leaking (6.1.3 (b) (i)) | 2 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 2 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Brake pipe excessively corroded | 2 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 2 |
| Horn not working (7.7 (a)) | 2 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting outrigger (6.1.6 (i) (i)) | 2 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Hole/Bumper support holed (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced step (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis[2 places] (5.3.6 (a) (i)) | 1 |
| Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer and inner seal (5.3.6 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Front Anti-roll bar linkage has an unsafe modification (5.3.3 (c) (i)) | 1 |
| Offside Front Anti-roll bar linkage has an unsafe modification (5.3.3 (c) (i)) | 1 |
| Nearside Rear Hydraulic brake calliper insecurely mounted (1.1.16 (c) (i)) | 1 |
| Offside Rear Hydraulic brake calliper insecurely mounted (1.1.16 (c) (i)) | 1 |
| Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill section (6.1.1 (c) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting missing (5.3.3 (a) (ii)) | 1 |
| Electrical wiring likely to touch hot or rotating parts ht lead (4.11 (a) (iii)) | 1 |
| Central Front Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt bbj (5.3.4 (b) (ii)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure is so weakened by corrosion within 30cm of a towbar mounting, the towbar is likely to become detached (6.1.6 (i) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Sill (6.2.2 (d) (ii)) | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Sill (6.2.2 (d) (ii)) | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Offside Rear fog lamp not working |1.3.2b| | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Inner sill |2.4.A.3| | 1 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Registration plate lamp issues | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Offside Front Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill ect (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength undersill area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength undersill area (5.3.6 (a) (i)) | 1 |
| Fuel system component leaking pump area (6.1.3 (b) (i)) | 1 |
| Nearside Front Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Offside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Subframe mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end panel (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting outer sill (6.2.2 (d) (i)) | 1 |
| Nearside Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting inner sill (6.2.2 (d) (i)) | 1 |
| Offside Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting outer sill (6.2.2 (d) (i)) | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Rear Towbar component excessively corroded (6.1.6 (a)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sil (6.1.1 (c) (i)) | 1 |
| Offside Rear Anti-roll bar damaged and seriously weakened d bush (5.3.3 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis rail (6.1.1 (c) (i)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect headlight lense cloudy (4.1.2 (c)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill. both sides (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak rear silencer (8.2.2.1 (b)) | 1 |
| Nearside Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Emissions not tested major leak in catayst unit and tail box (8.2.1.2 (d)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt outer joint (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt outer joint (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner / outer sills and inner arch area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/arch (6.1.1 (c) (i)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Rear Lower Anti-roll bar attachment bracket/mounting missing (5.3.3 (a) (ii)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill marked with chalk (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill marked with chalk (5.3.6 (a) (i)) | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill marked with chalk (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill marked with chalk (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill marked with chalk (5.3.6 (a) (i)) | 1 |
| Brakes imbalanced across an axle | 1 |
| Emissions unable to be completed EXHAUST LEAK. (8.2.1.2 (d)) | 1 |
| Central Rear Brake pipe excessively damaged BRAKE PIPE ON REAR AXLE. (1.1.11 (c)) | 1 |
| Emissions not tested EXHAUST LEAK. (8.2.1.2 (d)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outrigger (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting rear inner sill (6.1.6 (i) (i)) | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting rear sill (6.1.6 (i) (i)) | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Rear Seat belt anchorage prescribed area strength or continuity significantly reduced nearside and offside (7.1.1 (a) (i)) | 1 |
| Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush likely to become detached Anti roll bar D bush bracket broken & detatched (5.3.4 (a) (ii)) | 1 |
| Front Headlamp light source and lamp not compatible Existing halogen headlamp units on vehicles first used on or after 1 April 1986 must not be converted to be used with high intensity discharge (HID) or light emitting diode (LED) bulbs. (4.1.4 (c)) | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer (6.1.2 (a)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member corner (6.1.1 (c) (i)) | 1 |
| Front Vehicle structure is fractured and structural rigidity is significantly reduced below radiator cross member (6.1.1 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn missing (5.3.4 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sil (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch and sill end (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced arch (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner seal (5.3.6 (a) (i)) | 1 |
| Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt Both (5.3.4 (b) (ii)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected suspension arm mounting area (5.3.6 (a) (ii)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected suspension arm mounting area (5.3.6 (a) (ii)) | 1 |
| Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Headlamp aim not tested (4.1.2 (b)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting outrigger (6.1.6 (i) (i)) | 1 |
| Nearside Rear Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Rear Seat belt missing seat belt and buckles missing from rear seats (7.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits 0.63% (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits 0.43% (8.2.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength end of sill inner and outer sills detached from eachother (5.3.6 (a) (i)) | 1 |
| Rear Seat belt buckle missing possibly under rear seat (7.1.2 (d)) | 1 |
| Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced panel corner behind bumper (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced panel (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure inadequately repaired such that structural rigidity is significantly reduced sill (6.1.1 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure inadequately repaired such that structural rigidity is significantly reduced sill (6.1.1 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear of arch (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front of arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front of arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced panel behind bumper (6.1.1 (c) (i)) | 1 |
| Rear Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users coolant (8.4.1 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis / outrigger (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL AREA (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL AREA (5.3.6 (a) (i)) | 1 |
| Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Offside Rear fog lamp adversely affected by the operation of another lamp when brake operated (4.5.4 (b)) | 1 |
| Emissions not tested co high (8.2.1.2 (d)) | 1 |
| Electrical wiring insecure Under bonnet and under dvrs dash |1.9.2a| | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Rear fog lamp switch missing |1.3.1a| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 1 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Registration plate issues | 1 |
| Windscreen in such a condition that visibility through swept area is seriously affected (3.2 (c) (ii)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Nearside Front Suspension arm attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Rear Vehicle structure is so weakened by corrosion within 30cm of a towbar mounting, the towbar is likely to become detached (6.1.6 (i) (ii)) | 1 |
| Offside Front Sub-frame corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Windscreen in an unacceptable condition (3.2 (c) (i)) | 1 |
| Central Front Exhaust fumes causing a danger to health of persons on board exaust front pipe (6.1.2 (b) (ii)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Nearside Rear Shock absorbers has an excessively worn bush bottom bush (5.3.2 (c)) | 1 |
| Offside Rear Shock absorbers has an excessively worn bush bottom bush (5.3.2 (c)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |