| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 69 |
| Headlamp aim out of alignment | 44 |
| Brake pipe excessively corroded | 28 |
| Registration plate lamp issues | 22 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 21 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 19 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 17 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 14 |
| Windscreen washer not working | 14 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 13 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 12 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 12 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 12 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 11 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 11 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 10 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 10 |
| Horn not working (7.7 (a)) | 10 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 9 |
| Anti-lock braking system warning lamp indicates an ABS fault | 8 |
| Brakes imbalanced across an axle | 8 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 8 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 8 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 8 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 8 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 8 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 8 |
| Offside Rear fog lamp not working |1.3.2b| | 7 |
| Rear fog lamp not working |1.3.2b| | 7 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 7 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 7 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 7 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 6 |
| Registration plate issues | 6 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 6 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 6 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 6 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 6 |
| Nearside Front Shock absorbers has a serious fluid leak | 6 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 6 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 6 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 6 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 6 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 6 |
| Rear fog lamp tell tale not working |1.3.1b| | 5 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 5 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 5 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 5 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 5 |
| Front brake disc in such a condition that it is seriously weakened | 5 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 5 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 5 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 5 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 5 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 5 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 5 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 5 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
| Rear brake disc in such a condition that it is seriously weakened | 4 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 4 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 4 |
| Battery insecure |1.9.1| | 4 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 4 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Offside Front Shock absorbers has a serious fluid leak | 4 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Nearside Stop lamp not working |1.2.1b| | 4 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 4 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 4 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 4 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 4 |
| Offside Front front brake binding |3.7.B.1| | 4 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 4 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 4 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 4 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 3 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 3 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 3 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 3 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 3 |
| Centre Exhaust system not adequately supported |7.1.1| | 3 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 3 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 3 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 3 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 3 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 3 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 3 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 3 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 3 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 3 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 3 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 3 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 3 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 3 |
| Fuel system component leaking (6.1.3 (b) (i)) | 3 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Stop lamp not working (1.2.1b) | 3 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 3 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 2 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 2 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 2 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Emissions not tested |7.0| | 2 |
| Power steering component leaking steering rack (2.1.5 (a)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 2 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 2 |
| Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 2 |
| Rear fog lamp switch missing |1.3.1a| | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 2 |
| Lower Steering column universal joint has excessive wear or play (2.2.2 (c)) | 2 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 2 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Nearside Rear Bumper insecure (6.1.4 (a) (i)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 2 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 2 |
| Offside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 2 |
| Offside Front Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner arch (7.1.1 (a) (i)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 2 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 2 |
| Nearside Front front brake binding |3.7.B.1| | 2 |
| Horn not working |1.6.2a| | 2 |
| Central Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 2 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 2 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Horn sound not in accordance with requirements (7.7 (c)) | 2 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 2 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 2 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 2 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Front Position lamp likely to become detached (4.2.1 (c) (ii)) | 2 |
| Offside Front Seat belt damaged (7.1.2 (b) (i)) | 2 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Nearside Rear Brake disc contaminated (1.1.14 (b)) | 2 |
| Nearside Rear Anti-roll bar linkage attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 2 |
| Offside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 2 |
| Headlamp aim not tested (4.1.2 (b)) | 2 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush |5.3.4 |a| |i|| | 2 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Front position lamp(s) not working (1.1.A.3b) | 2 |
| Rear fog lamp not working (1.3.2b) | 2 |
| Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Steering rack gaiter split (2.2.D.2d) | 2 |
| Emissions unable to be completed (8.2.2.2 (e)) | 2 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 2 |
| Offside Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Offside Rear fog lamp missing |1.3.2a| | 2 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 2 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 2 |
| Offside Front Lower Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end (5.3.6 (a) (i)) | 2 |
| Offside Rear Vehicle structure is so weakened by corrosion within 30cm of a towbar mounting, the towbar is likely to become detached (6.1.6 (i) (ii)) | 2 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |