Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 59 |
Registration plate lamp issues | 30 |
Rear fog lamp not working |1.3.2b| | 17 |
Headlamp aim out of alignment | 15 |
Registration plate issues | 11 |
Offside Front position lamp|s| not working |1.1.A.3b| | 10 |
Offside Rear fog lamp not working |1.3.2b| | 9 |
Anti-lock braking system warning lamp indicates an ABS fault | 9 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 8 |
Rear fog lamp emits a light other than red |1.3.2e| | 7 |
Rear fog lamp tell tale not working |1.3.1b| | 7 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 6 |
Rear fog lamp missing |1.3.2a| | 6 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 6 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 5 |
Battery insecure |1.9.1| | 5 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Rear fog lamp tell tale missing |1.3.1b| | 5 |
Nearside Stop lamp not working |1.2.1b| | 5 |
Offside Rear fog lamp missing |1.3.2a| | 4 |
Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 4 |
Offside Headlamp not working on dipped beam |1.7.5a| | 4 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 4 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
Windscreen washer not working | 4 |
Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
Rear fog lamp does not emit a steady red light |1.3.2e| | 4 |
Rear fog lamp switch missing |1.3.1a| | 4 |
Offside Rear fog lamp emits a light other than red |1.3.2e| | 4 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
Rear fog lamp insecure |1.3.2a| | 4 |
Rear fog lamp missing (4.5.1 (a) (ii)) | 3 |
Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 3 |
Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 3 |
Offside Rear Shock absorbers has a serious fluid leak | 3 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 3 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
Offside Battery insecure |1.9.1| | 3 |
Brake pipe excessively corroded | 3 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 3 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 3 |
Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
Horn not working |1.6.2a| | 3 |
Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
Offside Stop lamp not working |1.2.1b| | 3 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Exhaust system not adequately supported |7.1.1| | 3 |
Rear fog lamp has less than 50% of the light sources illuminating |1.3.2b| | 3 |
Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 3 |
Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 3 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Parking brake lever has no reserve travel |3.1.6b| | 2 |
Horn not working (1.6.2a) | 2 |
Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 2 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 2 |
Headlamp not working on dipped beam |1.7.5a| | 2 |
Headlamp not working on main beam |1.7.5a| | 2 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 2 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Brake pedal creeps down when held under pressure |3.3.B.1a| | 2 |
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 2 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 2 |
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Nearside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 2 |
Offside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 2 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 2 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 2 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Rear fog lamp switch faulty |1.3.1a| | 2 |
Nearside Rear Shock absorbers has a serious fluid leak | 2 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 2 |
Brakes imbalanced across an axle | 2 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Offside Front Position lamp not working |4.2.1 |a|| | 2 |
Oil leaking excessively from engine |8.4.1 |a| |i|| | 2 |
Offside Rear Direction indicator not working |1.4.A.2c| | 2 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 2 |
Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
Rear brake binding | 2 |
Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Rear Rear fog lamp not working |1.3.2b| | 2 |
Offside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 2 |
Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 2 |
Nearside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
Nearside Parking brake inoperative on one side (1.4.1 (a)) | 2 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
Nearside Front Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Nearside Front Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
Nearside Rear Towbar excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Offside Rear Towbar excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Rear Exhaust system not adequately supported |7.1.1| | 1 |
Exhaust system not adequately supported (7.1.1) | 1 |
Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering out rigger (6.1.1 (c) (ii)) | 1 |
Nearside Rear Inner Floor excessively deteriorated drop sill (6.2.4 (a) (i)) | 1 |
Central Inner Exhaust system insecure Back box (6.1.2 (a)) | 1 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn saddle bush (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar pin or bush likely to become detached saddle bush (5.3.4 (a) (ii)) | 1 |
Offside Rear fog lamp not working (1.3.2b) | 1 |
Rear fog lamp tell tale not working (1.3.1b) | 1 |
Battery insecure (1.9.1) | 1 |
Nearside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2) | 1 |
Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2) | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded (5.2.6) | 1 |
Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Power steering component leaking rack (2.1.5 (a)) | 1 |
Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected out riger (5.3.6 (a) (ii)) | 1 |
Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
Front Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Lower Suspension component ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
Nearside Position lamp not working |4.2.1 |a|| | 1 |
Nearside Front Direction indicator incorrect colour |4.4.3 |a|| | 1 |
Rear Anti-roll bar pin or bush excessively worn Both nearside and offside |5.3.4 |a| |i|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WHEEL ARCH |5.3.6 |a| |i|| | 1 |
Offside Headlamp not working on main beam |1.7.5a| | 1 |
Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
Hydraulic fluid leaking excessively Steering rack (8.4.1 (a) (i)) | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded sill to floor |5.2.6| | 1 |
Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both rear inner sills (5.3.6 (a) (i)) | 1 |
Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Rear Anti-roll bar pin or bush excessively worn Both rear ARB D bushes (5.3.4 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill closing panel |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill closing panel |5.3.6 |a| |i|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch |5.3.6 |a| |i|| | 1 |
Brake performance not tested due to rear brakes binding |1.2.1 |g|| | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch |5.3.6 |a| |i|| | 1 |
Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
Offside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Front Brake pedal creeps down when held under pressure |3.3.B.1a| | 1 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Nearside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
Offside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
Offside Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 1 |
Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction |3.1 |a| |ii|| | 1 |
Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Offside Rear Anti-roll bar pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
Fuel cap/sealing device missing |7.2.4a| | 1 |
Front Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front subframe mount (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension arm mount (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area is inadequately repaired suspension arm mount (5.3.6 (a) (i)) | 1 |
Offside Rear Position lamp not working not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
Nearside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced Wheel arch (6.1.1 (d) (i)) | 1 |
Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced Wheel arch (6.1.1 (d) (i)) | 1 |
Nearside Front Integral body structure inadequately repaired such that structural rigidity is significantly reduced Wheel arch (6.1.1 (d) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Steering rack has excessive free play detected at the steering wheel (steering rack fitted) Lower UJ worn (2.3 (a) (i)) | 1 |
Fuel tank leaking (6.1.3 (b) (i)) | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mounting area (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength subframe mounting area (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Windscreen wiper not working (3.4 (a)) | 1 |
Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill in 3 places (7.1.1 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Horn not working (7.7 (a)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill inner (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front crossmember (6.1.1 (c) (i)) | 1 |
Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Nearside Rear Anti-roll bar linkage has excessive play in a pin/bearing |2.4.G.2| | 1 |
Nearside Inner Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Inner Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Towbar component excessively corroded (6.1.6 (a)) | 1 |
Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
Rear Passengers seat backrest cannot be secured in the upright position. rear (6.2.6 (a) (i)) | 1 |
Rear Seat belt missing rear (7.1.2 (a)) | 1 |
Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
Offside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Offside Rear Coil spring mounting corroded and seriously weakened |5.3.1 |b| |i|| | 1 |
Nearside Rear Coil spring mounting corroded and seriously weakened |5.3.1 |b| |i|| | 1 |
Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wing |6.1.1 |c| |i|| | 1 |
Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Front Tie bar/rod ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Fuel system component leaking |7.2.3| | 1 |
Nearside Front Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 1 |
Braking system leaking |3.6.A.1| | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wing (6.1.1 (c) (i)) | 1 |
Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wing (6.1.1 (c) (i)) | 1 |
Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 1 |
Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
Offside Rear Seat belt not functioning as intended (7.1.2 (c)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected chassis leg (5.3.6 (a) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at shocker mtg (5.3.6 (a) (i)) | 1 |
Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner panel ctr (5.3.6 (a) (i)) | 1 |
Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect re-fit bulb (4.1.2 (c)) | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired chassis not seam welded (5.3.6 (a) (i)) | 1 |
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Rear Upper Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Offside Front Fuel system component leaking pump (6.1.3 (b) (i)) | 1 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement and o/s/r |d bushes| |2.4.G.2| | 1 |
Nearside Front Anti-roll bar linkage has excessive play in a ball joint o/s/f and o/s/r drop links |2.4.G.2| | 1 |
Nearside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Rear Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
Offside Rear Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
Nearside Front Battery insecure |1.9.1| | 1 |
Offside Front Battery insecure |1.9.1| | 1 |
Main beam tell-tale not working (4.9.1 (a) (ii)) | 1 |
Offside Front Shock absorbers has a serious fluid leak | 1 |
Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
Nearside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
Headlamp has a product on the light source so that the light output is severely reduced NS + OS (4.1.4 (b)) | 1 |
Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength NS + OS outer rigger / inner sills (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Battery insecure |1.9.1| | 1 |
Offside Rear Anti-lock braking system wiring excessively damaged (1.6 (d)) | 1 |
Offside Rear Anti-lock braking system component missing sensor (1.6 (e)) | 1 |
Offside Headlamp aim so that beam "kick up" is not visible on the screen |1.8.B.1| | 1 |
Offside Front Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Exhaust emissions exceed level of metered smoke for a turbo charged engine |8.2.2.2 |b|| | 1 |
Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Offside Rear fog lamp has less than 50% of the light sources illuminating |1.3.2b| | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt upper and lower |5.3.4 |b| |ii|| | 1 |
Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Rear Upper Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Rear fog lamp switch inoperative (4.5.3 (a) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock mount (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wing sill & rear chassis (6.1.1 (c) (i)) | 1 |
Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced panel and chassis (6.1.1 (c) (i)) | 1 |
Nearside Rear Upper Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Rear Lower Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Lower Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Inner Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Inner Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Central Exhaust system insecure (6.1.2 (a)) | 1 |
Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Front brake application uneven | 1 |
Rear Rear fog lamp missing |1.3.2a| | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Suspension arm (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Suspension arm (5.3.6 (a) (i)) | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Offside Front Rear fog lamp not working |1.3.2b| | 1 |
Offside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Windscreen wiper blade insecure | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded suspension arm mounting area |2.4.A.3| | 1 |
Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Anti-lock braking system warning lamp does not illuminate |3.4.1b| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded sill end panel |2.4.A.3| | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting crossmember and lower wing area |6.6.6| | 1 |
Nearside front brake binding |3.7.B.1| | 1 |
Rear parking brake recording little or no effort | 1 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Headlamp aim not tested |4.1.2 |b|| | 1 |
Nearside Rear Position lamp missing |4.2.1 |a|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt retaining clip not secure . boot insecure |6.1.7 |g| |ii|| | 1 |
Offside Front Service brake excessively fluctuating |1.2.1 |e|| | 1 |
Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 1 |
Offside Rear Anti-roll bar attachment bracket/mounting insecure missing |5.3.3 |a| |i|| | 1 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Front Inner Suspension component mounting prescribed area is excessively corroded sill. |2.4.A.3| | 1 |
Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills |5.3.6 |a| |i|| | 1 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Offside Front Position lamp not working side light (4.2.1 (a) (ii)) | 1 |
Offside Rear Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
Rear fog lamp likely to become detached |4.5.1 |c| |ii|| | 1 |
Front Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
Nearside Front Outer Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Rear Outer Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Rear Inner Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Inner Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Rear Seat belt retracting mechanism defective |5.2.5b| | 1 |
Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Outer Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Engine MIL inoperative or indicates a malfunction |8.2.2.2 |g|| | 1 |
Nearside Rear Outer Position lamp not working |4.2.1 |a|| | 1 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Anti-roll bar pin or bush excessively worn D bush |5.3.4 |a| |i|| | 1 |
Nearside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill and outrigger (6.1.1 (c) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill and outrigger (6.1.1 (c) (i)) | 1 |
Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
Nearside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill holed |6.1.1 |c| |i|| | 1 |
Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill holed |6.1.1 |c| |i|| | 1 |
Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill holed |6.1.1 |c| |i|| | 1 |
Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Front and centre sill holed |6.1.1 |c| |i|| | 1 |
Offside Rear Suspension rod pin or bush excessively worn Rear trailing arm to axle bush |5.3.4 |a| |i|| | 1 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Rear fog lamp lens defective such that emitted light is adversely affected |4.5.1 |b| |ii|| | 1 |
Nearside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
Offside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
Offside Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
Offside Inner Front Electrical wiring inadequately supported |1.9.2a| | 1 |
Nearside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
Offside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Emissions not tested |7.4.B.1| | 1 |
Rear Mechanical brake component has restricted free movement | 1 |
Nearside Front Position lamp light intensity significantly reduced |4.2.3 |a| |ii|| | 1 |
Offside Front Position lamp light intensity significantly reduced |4.2.3 |a| |ii|| | 1 |
Offside Rear Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Nearside Front Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Rear Exhaust has a major leak of exhaust gases rear exhaust at joint |7.1.2| | 1 |
Nearside Rear Suspension spring mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area |5.3.6 |a| |i|| | 1 |
Offside Direction indicators flashing more than 120 times a minute |1.4.A.2g| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded inner sill / floor area |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded inner sill / floor area |2.4.A.3| | 1 |
Rear fog lamp has a product on the light source so it is not visible from a reasonable distance |1.3.2d| | 1 |
Offside Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill & outrigger |5.3.6 |a| |i|| | 1 |
Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Fuel cap/sealing device ineffective |6.1.3 |b| |i|| | 1 |
Nearside Front Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
Central Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
Offside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced rear outrigger (7.1.1 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced integral structure (7.1.1 (a) (i)) | 1 |
Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced integral structure (7.1.1 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Driver`s door cannot be opened from inside the vehicle |6.2.3 |a|| | 1 |
Front passenger door cannot be opened from inside the vehicle |6.2.3 |a|| | 1 |
Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Emissions not tested emits excessive smoke (8.2.2.2 (e)) | 1 |
Nearside Front Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Headlamp aim not tested (4.1.2 (b)) | 1 |
Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
Speedometer clearly inoperative |6.7.2| | 1 |
Power steering component leaking steering rack |2.1.5 |a|| | 1 |
Offside Rear Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
Front Undertray likely to become detached |6.2.1 |a| |ii|| | 1 |
Offside Rear Direction indicators not working |1.4.A.2c| | 1 |
Offside Front All position lamps not working |1.1.A.3b| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded inner arch |5.2.6| | 1 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Rear Suspension arm pin or bush excessively worn d-bush (5.3.4 (a) (i)) | 1 |
Offside Rear Suspension arm pin or bush excessively worn d-bush (5.3.4 (a) (i)) | 1 |
Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Rear fog lamp emits a light other than red red tape applied to lense |1.3.2e| | 1 |
Offside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Steering rack retaining devices dangerously loose (2.1.2 (a) (ii)) | 1 |
Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member area (5.3.6 (a) (i)) | 1 |
Nearside Rear Anti-roll bar linkage fractured broken (5.3.3 (b) (ii)) | 1 |
Rear Anti-roll bar pin or bush excessively worn d bushes (5.3.4 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill/step (7.1.1 (a) (i)) | 1 |
Battery insecure Both batteries |1.9.1| | 1 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Offside Front Lower Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Rear Lower Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Wheel nut|s| missing |4.2.A.1e| | 1 |
Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 1 |
Nearside Rear Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Headlamp aim so that beam "kick up" is not visible on the screen both headlamps faded, no beam image |4.1.2 |a|| | 1 |
Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
Rear Vehicle structure excessively corroded within 30cm of towbar mounting cross member |6.6.6| | 1 |
Nearside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
Nearside Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
Offside Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |