Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 14 |
Registration plate lamp issues | 11 |
Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 9 |
Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 7 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 5 |
Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 4 |
Headlamp aim out of alignment | 4 |
Centre Stop lamp not working |1.2.1b| | 4 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
Horn not working |1.6.2a| | 3 |
Rear fog lamp not working |1.3.2b| | 3 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 3 |
Parking brake: efficiency below requirements |3.7.B.7| | 3 |
Rear parking brake recording little or no effort | 3 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 3 |
Rear fog lamp tell tale not working |1.3.1b| | 2 |
Horn not working |7.7 |a| |ii|| | 2 |
Rear fog lamp emits a light other than red |1.3.2e| | 2 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
Offside Rear Stop lamp not working |1.2.1b| | 2 |
Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
Centre Rear Statutory seat belt missing |5.1.1| | 2 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Stop lamp not working |1.2.1b| | 2 |
Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 2 |
Nearside Outer Body has a projection caused by corrosion sill |6.1.C.1| | 1 |
Offside Inner Body has a projection caused by corrosion sill |6.1.C.1| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside front brake binding |3.7.B.1| | 1 |
Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill marked with yellow chalk (6.1.1 (c) (i)) | 1 |
Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill marked with yellow chalk (6.1.1 (c) (i)) | 1 |
Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Nearside Front Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Nearside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill Area (7.1.1 (a) (i)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill Area (7.1.1 (a) (i)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill Area (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner/Outer Sill Area (5.3.6 (a) (i)) | 1 |
Nearside Front Lower Suspension arm ball joint likely to become detached Split Pin Missing (5.3.4 (a) (ii)) | 1 |
Offside Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting 30 cm of tow bar mounting |6.2.2 |d| |i|| | 1 |
Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting 30 cm of tow bar mounting |6.2.2 |d| |i|| | 1 |
Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting suspension component mounting |6.2.2 |d| |i|| | 1 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting suspension component mounting |6.2.2 |d| |i|| | 1 |
Offside Rear Towbar attachment defective mounting bolt loose |6.1.6 |c| |i|| | 1 |
Nearside Front Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 1 |
Offside Front Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 1 |
Nearside Inner Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Inner Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Rear Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Front position lamp|s| not working |1.1.A.3b| | 1 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Stop lamp not working |1.2.1b| | 1 |
Central Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 1 |
Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 1 |
Front Lower Steering column universal joint has excessive wear or play (2.2.2 (c)) | 1 |
Exhaust has a major leak of exhaust gases flex section (6.1.2 (a)) | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Rear Stop lamp not working |1.2.1b| | 1 |
Offside Rear fog lamp not working |1.3.2b| | 1 |
Offside Rear fog lamp has a product on the lens so it is not visible from a reasonable distance |1.3.2d| | 1 |
Nearside Rear reflector missing |1.5.1a| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Offside Rear Anti-roll bar linkage fractured |2.4.G.1| | 1 |
Offside Front Seat belt affected by an insecure seat fixing |5.2.1b| | 1 |
Nearside Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Rear fog lamp missing |1.3.2a| | 1 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Fuel pipe union leaking |7.2.3| | 1 |
Fuel pipe union leaking LPG tank connector |7.2.3| | 1 |
rear parking |secondary| brakes imbalanced | 1 |
Nearside Rear rear brake excessively fluctuating |3.7.B.3| | 1 |
Nearside Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill to arch |2.4.A.3| | 1 |
Offside Rear Inner Suspension component mounting prescribed area is excessively corroded under sill by heater |2.4.A.3| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
Offside Rear Inner Suspension component mounting prescribed area is excessively corroded under sill to arch |2.4.A.3| | 1 |
Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded wing behind bumper |5.2.6| | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch to sill end (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch corroded & holed (fuel filler area & suspension) (5.3.6 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing by horn (5.3.6 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing behind mud flap corroded & holed (5.3.6 (a) (i)) | 1 |
Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member under bumper corroded & holed (5.3.6 (a) (i)) | 1 |
Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member corroded & holed under bumper (5.3.6 (a) (i)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing under washer bottle corroded & holed (5.3.6 (a) (i)) | 1 |
Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill corroded & holed by rear heater pipes (5.3.6 (a) (i)) | 1 |
Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill corroded & holed (5.3.6 (a) (i)) | 1 |
Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced cross member (7.1.1 (a) (i)) | 1 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced cross member (7.1.1 (a) (i)) | 1 |
Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced cross member to inner wing over exhaust (7.1.1 (a) (i)) | 1 |
Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 1 |
Exhaust hydrocarbon content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
Exhaust carbon monoxide content at idle exceeds default limits |8.2.1.2 |b|| | 1 |
Exhaust emissions carbon monoxide content excessive LPG GAS TEST |8.2.1.2 |b|| | 1 |
Exhaust emissions hydrocarbon content excessive LPG GAS TEST |8.2.1.2 |b|| | 1 |
Centre Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Nearside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Front Anti-roll bar has excessive play in a pin/bush Both |2.4.G.2| | 1 |
Anti-lock braking system warning lamp indicates an ABS fault | 1 |
Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Supplementary restraint system warning lamp indicates a fault |7.1.6 |a|| | 1 |
Nearside Front Lower Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Exhaust catalytic converter obviously defective |8.2.1.1 |a|| | 1 |
Nearside Front Upper Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Upper Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Rear Mechanical brake component has restricted free movement | 1 |
Rear Rear fog lamp missing |1.3.2a| | 1 |
Rear fog lamp switch missing |1.3.1a| | 1 |
Centre Rear Stop lamp not working |1.2.1b| | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Brake pipe excessively corroded | 1 |
Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 1 |
Nearside Rear Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 1 |
Offside Rear Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 1 |
Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sil (6.1.1 (c) (i)) | 1 |
Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |