Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 25 |
Registration plate lamp issues | 25 |
Headlamp aim out of alignment | 17 |
Rear fog lamp not working |1.3.2b| | 14 |
Offside Rear fog lamp not working |1.3.2b| | 13 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
Offside Front position lamp|s| not working |1.1.A.3b| | 11 |
Rear fog lamp tell tale not working |1.3.1b| | 7 |
Parking brake: efficiency below requirements |3.7.C.1b| | 6 |
Rear parking brake recording little or no effort | 6 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 5 |
Offside Rear Rear fog lamp not working |1.3.2b| | 5 |
Nearside Stop lamp not working |1.2.1b| | 5 |
Brake pipe excessively corroded | 5 |
Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 5 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 4 |
Rear brake binding | 4 |
Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 4 |
Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 4 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Windscreen washer not working | 4 |
Mechanical brake component has restricted free movement | 4 |
Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
Rear fog lamp insecure |1.3.2a| | 3 |
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Parking brake lever has no reserve travel |3.1.6b| | 3 |
Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 3 |
Offside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 3 |
Rear fog lamp missing |1.3.2a| | 3 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 3 |
Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Stop lamp not working |1.2.1b| | 3 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Rear Stop lamp not working |1.2.1b| | 3 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
Parking brake: efficiency below requirements |3.7.B.7| | 2 |
Nearside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
Rear Rear fog lamp missing |1.3.2a| | 2 |
Nearside front brake binding |3.7.B.1| | 2 |
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Offside Rear Lower Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Brakes imbalanced across an axle | 2 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Rear Passenger`s seat cannot be secured in the upright position. |6.2.A.2| | 2 |
Rear fog lamp emits a light other than red |1.3.2e| | 2 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 2 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 2 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Horn not working |1.6.2a| | 2 |
Rear Mechanical brake component has restricted free movement | 2 |
Offside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 2 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
Offside Rear fog lamp missing |1.3.2a| | 2 |
Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Nearside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
Offside Front Steering rack gaiter split |2.2.D.2d| | 2 |
Nearside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Offside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Anti-lock braking system warning lamp indicates an ABS fault | 2 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
Front brake application uneven | 2 |
Offside Rear Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
Nearside Front position lamp|s| insecure |1.1.A.3a| | 1 |
Nearside Direction indicator insecure |1.4.A.2b| | 1 |
Exhaust has a part missing |7.1.1a| | 1 |
Position lamp switch faulty |1.1.A.1| | 1 |
Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 1 |
Nearside Front Front position lamp|s| insecure |1.1.A.3a| | 1 |
Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
Offside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Offside Inner Sill has heavy corrosion all along Sill. |6.1.1 |c| |i|| | 1 |
Rear brake application uneven | 1 |
Rear Service brake is causing the vehicle to swerve to the nearside |3.7.C.2| | 1 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Rear Rear fog lamp tell tale not working |1.3.1b| | 1 |
Rear Rear fog lamp not working |1.3.2b| | 1 |
Offside Rear Rear fog lamp missing |1.3.2a| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill and inner wheel arch |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Nearside Rear Lower Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement D bush |2.4.G.2| | 1 |
Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement D bush |2.4.G.2| | 1 |
Nearside Front Lower Suspension arm ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Lower Suspension arm ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Rear fog lamp insecure |1.3.2a| | 1 |
Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Nearside Rear Anti-roll bar linkage rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Lower Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Battery insecure |1.9.1| | 1 |
Nearside Rear passenger door cannot be opened from outside the vehicle |6.2.B.1c| | 1 |
Service brake: efficiency below requirements |3.7.C.1a| | 1 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Nearside Rear Anti-roll bar insecure |2.4.G.1| | 1 |
Nearside Outer Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
Emissions not tested |7.0| | 1 |
Nearside Inner Rear Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Inner Rear Anti-roll bar synthetic mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Rear Passenger`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
Nearside Front Lower Steering locking device missing lower balljoint |2.1.3 |d|| | 1 |
Offside Front Lower Steering locking device missing balljoint |2.1.3 |d|| | 1 |
Offside Rear Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Inner Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Rear fog lamp switch faulty |1.3.1a| | 1 |
Nearside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
Registration plate issues | 1 |
Front Statutory seat belt missing |5.1.1| | 1 |
Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
Offside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Torque/reaction arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Rear fog lamp switch inoperative (4.5.3 (a) (ii)) | 1 |
Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
Offside Steering rack gaiter split |2.2.D.2d| | 1 |
Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Exhaust emissions exceed level of metered smoke for a turbo charged engine |8.2.2.2 |b|| | 1 |
Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Engine MIL inoperative or indicates a malfunction |8.2.2.2 |g|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner & outer sill |5.3.6 |a| |i|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Nearside Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Offside Front Lower Bonded suspension unit deteriorated and cannot function as intended |2.4.F.3| | 1 |
Central Stop lamp obscured more than 50% |1.2.1c| | 1 |
Nearside Front front brake binding |3.7.B.1| | 1 |
Horn not working |7.7 |a| |ii|| | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Offside Rear Rear fog lamp insecure |1.3.2a| | 1 |
Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Offside Inner Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Rear Inner Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area is inadequately repaired sill/box section (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/box section/wheel arch (5.3.6 (a) (i)) | 1 |
Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/wheel arch (5.3.6 (a) (i)) | 1 |
Front Service brake grabbing severely both binding (1.2.1 (c)) | 1 |
Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside front brake binding |3.7.B.1| | 1 |
Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Battery insecure |1.9.1| | 1 |
Offside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
Nearside Inner Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Inner Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 1 |
Nearside Front Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Nearside Outer Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Outer Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Windscreen wiper blade insecure | 1 |
Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Rear brake disc excessively pitted |3.5.1h| | 1 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Rear Electrical wiring insecure and connectors likely to become disconnected |4.11 |a| |ii|| | 1 |
Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch (5.3.6 (a) (i)) | 1 |
Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded under sill |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded under sills |2.4.A.3| | 1 |
Rear Towbar component excessively corroded |6.6.1| | 1 |
Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Offside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength On inner sill |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength On inner and outer sills |5.3.6 |a| |i|| | 1 |
Nearside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and nearside inner and outer sills |5.3.6 |a| |i|| | 1 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Offside Rear Anti-roll bar linkage missing drop link (5.3.3 (a) (ii)) | 1 |
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Front Seat belt damaged (7.1.2 (b) (i)) | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill wheel arch area (6.1.1 (c) (i)) | 1 |
Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Central Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front cross member gone all the way across (6.1.1 (c) (i)) | 1 |
Power steering malfunctioning (2.1.5 (a)) | 1 |
Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch to rear valance (7.1.1 (a) (i)) | 1 |
Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced rear valance to wheel arch also within 30 cm of towbar (7.1.1 (a) (i)) | 1 |
Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength chassis above spring behind wheel (5.3.6 (a) (i)) | 1 |
Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Nearside Front Outer Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Lower Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Lower Suspension arm attachment bracket/mounting insecure no split pin in securing nut (5.3.3 (a) (i)) | 1 |
Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
Front Headlamp has a product on the lens so that the light output is severely reduced both sides (4.1.4 (b)) | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings crossmember |6.1.B.2| | 1 |
Offside Rear Anti-roll bar locating pin locking device missing and bush missing |2.4.G.3b| | 1 |
Central Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Offside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
Rear Exhaust has a major leak of exhaust gases silencer broken away |6.1.2 |a|| | 1 |
Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Offside Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Rear fog lamp switch missing |1.3.1a| | 1 |
Offside Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Fuel system component leaking |7.2.3| | 1 |
Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Offside Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Rear fog lamp insecure Lens missing |1.3.2a| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded Inner sill |2.4.A.3| | 1 |
Offside Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inside sill |6.1.B.2| | 1 |
Nearside Front Inner Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
Front Electrical wiring insecure |1.9.2a| | 1 |
Nearside Front Tie bar/rod ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Tie bar/rod ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Rear Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
Nearside Rear Seat belt missing (7.1.2 (a)) | 1 |
Offside Rear Seat belt missing (7.1.2 (a)) | 1 |
Offside Rear Anti-roll bar insecure |2.4.G.1| | 1 |
Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper spring turret (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper spring turret (5.3.6 (a) (i)) | 1 |
Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
Nearside Rear Inner Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Nearside Rear Outer Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Offside Rear Inner Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Offside Rear Outer Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
Nearside rear brakes release unevenly |3.7.B.4| | 1 |
Nearside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Front All position lamps not working |1.1.A.3b| | 1 |
Nearside Rear All position lamps not working |1.1.A.3b| | 1 |
Offside Rear Stop lamp not working |1.2.1b| | 1 |
Offside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Rear Towbar excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Offside Rear Towbar excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Rear Panhard rod severely distorted |2.4.G.1| | 1 |
Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
Nearside Front Upper Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Fuel cap/sealing device missing |7.2.4a| | 1 |
Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Driver`s seat insecure |6.2.A.1| | 1 |
Nearside Battery insecure |1.9.1| | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Rear brake disc excessively pitted |3.5.1h| | 1 |
Offside Rear brake disc excessively pitted |3.5.1h| | 1 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Front Outer Steering rack gaiter split |2.2.D.2d| | 1 |
Offside Front Headlamp not working on main beam |1.7.5a| | 1 |