Most common failures | No# failures |
---|
Headlamp aim out of alignment | 32 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 16 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 16 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 10 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 9 |
Horn not loud enough to be heard by another road user |1.7.3a| | 9 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 9 |
Roller brake test No brake control achieves an efficiency of 30%. |3.3.A2a| | 8 |
Horn not working |1.7.3a| | 6 |
Registration plate issues | 6 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 6 |
Rear Brake pedal has inadequate reserve travel |3.1.3b| | 5 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 5 |
Brake lever has inadequate reserve travel |3.1.3b| | 5 |
Roller brake test Neither brake control achieves an efficiency of 25% |3.3.A2b| | 5 |
Rear Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 5 |
Steering headbearing has excessive free play |2.2.2| | 4 |
Throttle operating incorrectly |6.2.1f| | 4 |
All position lamps do not illuminate immediately when switched on |1.1.3a| | 4 |
Riders seat insecure |6.2.1a| | 3 |
Front wheel spindle loose |2.3.5a| | 3 |
Floor brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.C1b| | 3 |
Offside Front suspension assembly component loose |2.3.1| | 3 |
Headlamp main beam affected by the operation of another lamp |1.2.2c| | 2 |
Headlamp dipped beam affected by the operation of the horn |1.2.2c| | 2 |
Front Gradient brake test indicates a severely grabbing brake |3.3.D1d| | 2 |
Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 2 |
Front Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 2 |
Front wheel has a loose wheel nut|s| |4.2.3a| | 2 |
Fuel cap does not fasten securely maintaining the sealing arrangement |7.2.2b| | 2 |
Front Gradient brake test indicates a sticking brake |3.3.D1c| | 2 |
Rear Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 2 |
Rear Gradient brake test indicates a binding brake |3.3.D1c| | 2 |
Front suspension assembly component loose |2.3.1| | 2 |
Centre Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 2 |
Stop lamp emits other than a steady red light |1.3.1b| | 2 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 2 |
Brake pedal has inadequate reserve travel |3.1.3b| | 2 |
Front Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort |3.3.A1c| | 2 |
Front Brake back plate|s| insecure |3.2.A1j| | 1 |
Front Front wheel bearings have excessive free play |2.3.5b| | 1 |
Rear Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Steering movement excessively stiff with the weight on the lower bearing (2.2.1a) | 1 |
Gradient brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.D1b| | 1 |
Offside Steering lock stop missing |2.1.3| | 1 |
Front Handlebar mounting excessively deteriorated |flexible type| |2.1.1d| | 1 |
Rear Roller brake test indicates brake effort fall disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Rear position lamp adversely affected by the operation of the horn |1.1.3b| | 1 |
Nearside Rear wheel rotation likely to be impeded |6.2.1b| | 1 |
Fuel cap does not fasten securely by a positive means |7.2.2b| | 1 |
Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
Rear reflector on motorcycle missing |1.4.1| | 1 |
Stop lamp remains on when the brakes are released | 1 |
Rear Floor brake test indicates a sticking brake |3.3.C2c| | 1 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Rear All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
Headlamp main beam affected by the operation of the horn |1.2.2c| | 1 |
Stop lamp affected by the operation of the horn |1.3.2| | 1 |
Offside Front Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Fairing so located that it is likely to impede the steering |2.1.2e| | 1 |
Front position lamp insecure |1.1.1c| | 1 |
Offside Steering lock stop ineffective |2.1.3| | 1 |
Rear Wheel corroded significantly reducing the original strength |4.2.1a| | 1 |
Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 1 |
Rear position lamp adversely affected by the operation of another lamp |1.1.3b| | 1 |
Stop lamp missing |1.3.3a| | 1 |
Rear Brake pedal insecure |3.1.2a| | 1 |
Rear Built up wheel has a loose bolt/s |4.2.1c| | 1 |
Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 1 |
Front wheel bearings are excessively rough |2.3.5b| | 1 |
Front Brake lever is so short and the brake cannot be readily applied |3.1.3c| | 1 |
Stop lamp not working |4.3.1 |a| |ii|| | 1 |
Inner Front Upper Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
Centre Front Gradient brake test indicates a sticking brake |3.3.D1c| | 1 |
Front Brake caliper|s| insecure |3.2.A1j| | 1 |
Front suspension fouling which affects the movement of the front suspension. |2.3.6a| | 1 |
Rear wheel insecure |4.2.3b| | 1 |
Rear wheel has a missing wheel nut|s| |4.2.3a| | 1 |
Rear Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Rear Brake lining|s| less than 1.5 mm thick |3.2.A1f|i|| | 1 |
Outer Rear Gradient brake test indicates a binding brake |3.3.D1c| | 1 |
Centre Rear Brake drum|s| securing bolt|s| loose |3.2.A1g| | 1 |
Brake pedal insecure |3.1.2a| | 1 |
Rear Brake locking device missing |3.2.A1e| | 1 |
Rear Brake performance not tested |3.3| | 1 |
Plate brake test No brake control achieves an efficiency of 30%. |3.3.B2a| | 1 |
Plate brake test Neither brake control achieves an efficiency of 25% |3.3.B2b| | 1 |
Front Headlamp aim headlamp deteriorated and function impaired |1.2.3a| | 1 |
Brake pedal insecure securing clip missing from pedal pivot point |3.1.2a| | 1 |
Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
Headlamp dipped beam affected by the operation of another lamp |1.2.2c| | 1 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Stop lamp affected by the operation of another lamp |1.3.2| | 1 |
Nearside Front Front suspension assembly component loose |2.3.1| | 1 |
Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Front Brake disc|s| insecure |3.2.A1g| | 1 |
Front Brake lever insecure cable fitting insecure to lever |3.1.2a| | 1 |
Nearside Handlebar handgrip missing |2.1.1c| | 1 |
Front suspension assembly excessive wear or free play in a front suspension component |2.3.4| | 1 |
Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Brake lever mounting insecure |3.1.2a| | 1 |
Front suspension assembly component loose damper fittings |2.3.1| | 1 |
Horn control defective |1.7.2a| | 1 |
Front Brake pipe union leaking fluid |3.2.B4| | 1 |
Front All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
Brake hose excessively deteriorated | 1 |
Front Brake hose fouling |3.2.B3b| | 1 |
Front Steering headbearing has excessive free play |2.2.2| | 1 |
Front Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Front Brake lever cannot be applied smoothly |3.1.3d| | 1 |
Front Clutch lever bent so it cannot be readily operated. |6.2.1g| | 1 |
Rear Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 1 |
Front Fuel cap sealing washer torn |7.2.2c| | 1 |
Front Leg shield insecure and likely to impede the steering |2.1.2e| | 1 |
Rear Rear suspension bush excessively deteriorated |2.4.A2a|i|| | 1 |
Front Front suspension has inadequate damping effect. |2.3.6c| | 1 |
Front Fuel tank leaking |7.2.1a| | 1 |
Rear Exhaust has part of the system missing |7.1.1a| | 1 |
Offside Front Front wheel has a loose wheel nut|s| |4.2.3a| | 1 |
Centre Rear Gradient brake test indicates a sticking brake |3.3.D1c| | 1 |
Centre Rear Brake pedal is bent and the brake cannot be readily applied |3.1.3c| | 1 |
Centre Front Horn not working |1.7.3a| | 1 |
Brake reaction bracket insecure |3.2.A1j| | 1 |
Rear Brake locking device insecure |3.2.A1e| | 1 |
Rear Stop lamp affected by the operation of another lamp |1.3.2| | 1 |
Front Brake master cylinder fluid level dangerously low |3.2.B1d| | 1 |
All position lamps adversely affected by the operation of the horn |1.1.3b| | 1 |
Headlamp incorrect colour |1.2.1| | 1 |
Exhaust markings indicating not for road use or similar wording |7.1.4| | 1 |
Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Rear Wheel has an excessively distorted bead rim. |4.2.2| | 1 |
Headlamp insecure |1.2.3b| | 1 |