Most common failures | No# failures |
---|
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 24 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 23 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 20 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 19 |
Headlamp aim out of alignment | 17 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 13 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 12 |
Steering headbearing has excessive free play |2.2.2| | 12 |
Rear Brake pedal has inadequate reserve travel |3.1.3b| | 10 |
Registration plate issues | 9 |
Horn not working |1.7.3a| | 9 |
Headlamp aim not tested |1.6| | 5 |
Rear Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 5 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 4 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 4 |
Throttle operating incorrectly |6.2.1f| | 4 |
Brake pedal has inadequate reserve travel |3.1.3b| | 4 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 4 |
Handlebar mounting clamp bolt loose |2.1.1a| | 3 |
Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 3 |
Front Steering headbearing has excessive free play |2.2.2| | 3 |
Front Horn not working |1.7.3a| | 3 |
Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 3 |
Floor brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.C1b| | 3 |
Riders seat insecure |6.2.1a| | 3 |
Roller brake test Neither brake control achieves an efficiency of 25% |3.3.A2b| | 3 |
Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 3 |
Horn not loud enough to be heard by another road user |1.7.3a| | 3 |
Headlamp insecure |1.2.3b| | 3 |
Wheel alignment incorrect which adversely affects the steering |2.5.1| | 2 |
Front position lamp deteriorated and function impaired |1.1.1b| | 2 |
Front Brake back plate|s| insecure |3.2.A1j| | 2 |
Handlebar mounting clamp loose |2.1.1a| | 2 |
Headlamp switch faulty |1.2.4| | 2 |
Front suspension has inadequate damping effect. |2.3.6c| | 2 |
Headlamp aim beam image kick up to the offside |1.6| | 2 |
Front Roller brake test indicates brake effort fall disproportional to brake lever or pedal effort |3.3.A1c| | 2 |
Centre Front Upper Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 2 |
Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 2 |
Rear Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 2 |
Rear Roller brake test indicates brake effort fall disproportional to brake lever or pedal effort |3.3.A1c| | 2 |
Rear Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 2 |
Front wheel has a loose wheel nut|s| |4.2.3a| | 2 |
Brake lever has inadequate reserve travel |3.1.3b| | 2 |
Front Roller brake test indicates a severely grabbing brake |3.3.A1b| | 2 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 2 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 2 |
Rear Floor brake test indicates a sticking brake |3.3.C2c| | 2 |
Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 2 |
Rear wheel has a loose wheel nut|s| |4.2.3a| | 1 |
Front suspension fouling which affects the movement of the front suspension. |2.3.6a| | 1 |
Front Brake lever cannot be released smoothly |3.1.3d| | 1 |
Rear position lamp incorrect colour |1.1.2b| | 1 |
Front Wheel alignment incorrect which adversely affects the handling |2.5.1| | 1 |
Front Front suspension assembly component excessively bent |2.3.1| | 1 |
Front Upper Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 1 |
Offside Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Nearside Front Brake cable has a significantly damaged outer casing. |3.2.A1b| | 1 |
Stop lamp does not illuminate immediately a brake applies rear brake |1.3.1a| | 1 |
Front suspension assembly component loose front spindle hub nut insecure |2.3.1| | 1 |
Throttle operating incorrectly does not return correctly |6.2.1f| | 1 |
Rear Brake linkage has abnormal movement due to maladjustment |3.2.A1i| | 1 |
Offside Front Throttle operating incorrectly |6.2.1f| | 1 |
Front Steering linkage has excessive free play |2.2.2| | 1 |
Rear reflector on motorcycle missing |1.4.1| | 1 |
Front Horn not loud enough to be heard by another road user |1.7.3a| | 1 |
Front Brake component has restricted free movement and operation is likely to be impeded |3.2.A1h| | 1 |
Front Front suspension has excessive stiffness in the suspension movement. |2.3.6b| | 1 |
Rear Brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
Rear Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort low effort, out of adjustment |3.3.A1c| | 1 |
Centre Rear Lower Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 1 |
Rear Fairings insecure and likely to impede the steering |2.1.2e| | 1 |
Fuel hose leaking |7.2.1a| | 1 |
Front Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Headlamp dipped beam affected by the operation of the horn |1.2.2c| | 1 |
Headlamp main beam affected by the operation of the horn |1.2.2c| | 1 |
Offside Motorcycle structure excessively corroded |6.1.1a| | 1 |
Nearside Motorcycle structure excessively corroded |6.1.1a| | 1 |
Motorcycle structure excessively corroded |6.1.1a| | 1 |
Front suspension has excessive stiffness in the suspension movement. |2.3.6b| | 1 |
Service brake: efficiency below requirements |3.7.B.7| | 1 |
Parking brake: efficiency below requirements |3.7.B.7| | 1 |
Front Hydraulic brake control creeps under load. |3.1.4a| | 1 |
Steering control fouling between components which interferes with the free movement of the steering |2.1.2a| | 1 |
Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Front Steering movement excessively stiff with the weight on the lower bearing |2.2.1a| | 1 |
Front suspension spring worn and seriously weakened |2.3.2b| | 1 |
Front Front position lamp incorrect colour |1.1.2a| | 1 |
Front Headlamp deteriorated and function impaired |1.2.3a| | 1 |
Front Steering movement excessively stiff with the wheel raised |2.2.1b| | 1 |
Front Wheel corroded significantly reducing the original strength |4.2.1a| | 1 |
Rear Fuel pipe leaking |7.2.1a| | 1 |
Roller brake test No brake control achieves an efficiency of 30%. |3.3.A2a| | 1 |
Offside Front Lower Brake cylinder leaking hydraulic fluid |3.2.B1e| | 1 |
Offside Steering lock stop missing |2.1.3| | 1 |
Front Brake lever attachment screws loose |3.1.2b| | 1 |
Floor brake test No brake control achieves an efficiency of 30%. |3.3.C1a| | 1 |
Floor brake test Neither brake control achieves an efficiency of 25% |3.3.C1b| | 1 |
Offside Rear Wheel has an excessively distorted bead rim. |4.2.2| | 1 |
Fuel cap does not fasten securely maintaining the sealing arrangement |7.2.2b| | 1 |
Fuel cap sealing washer missing |7.2.2c| | 1 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Front Front wheel bearings are excessively rough |2.3.5b| | 1 |
Rear Built up wheel has a bolt/s missing |4.2.1c| | 1 |
Rear Stop lamp damaged and function impaired |1.3.3a| | 1 |
Fairings so located that it is likely to impede the steering |2.1.2e| | 1 |
Rear Built up wheel has a loose bolt/s |4.2.1c| | 1 |
Front position lamp adversely affected by the operation of another lamp |1.1.3b| | 1 |
Front wheel spindle loose |2.3.5a| | 1 |
Front Brake cable has a significantly damaged outer casing. |3.2.A1b| | 1 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Steering movement excessively `notchy` with the weight on the lower bearing |2.2.1a| | 1 |
Rear Wheel has an excessively distorted bead rim. |4.2.2| | 1 |
Offside Steering lock stop ineffective |2.1.3| | 1 |
Front wheel bearings have excessive free play |2.3.5b| | 1 |
Offside Front Brake cable badly frayed |3.2.A1b| | 1 |
Headlamp aim beam image kick-up is to the offside |1.6.1| | 1 |
Steering movement excessively stiff with the weight on the lower bearing |2.2.1a| | 1 |
Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Front Front suspension assembly component loose |2.3.1| | 1 |
Front Front mudguard insecure |2.3.7| | 1 |
Headlamp incorrect colour |1.2.1| | 1 |
Fairing so located that it is likely to impede the steering |2.1.2e| | 1 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Inner Rear Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Centre Front Front position lamp flickers when tapped lightly by hand |1.1.3c| | 1 |
Centre Front Headlamp incorrect colour |1.2.1| | 1 |
Centre Front Handlebar mounting clamp loose |2.1.1a| | 1 |
All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
Steering movement excessively stiff with the wheel raised |2.2.1b| | 1 |
Front All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
Rear All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
Rear Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 1 |
Front wheel bearings are excessively rough |2.3.5b| | 1 |
Front Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 1 |
Front suspension assembly excessive wear or free play in a front suspension component |2.3.4| | 1 |
Front Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 1 |
Plate brake test No brake control achieves an efficiency of 30%. |3.3.B2a| | 1 |
Centre Rear Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Stop lamp not working |4.3.1 |a| |ii|| | 1 |
Rear wheel insecure |4.2.3b| | 1 |
Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 1 |
Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Front Front wheel has a missing wheel nut|s| |4.2.3a| | 1 |
Floor brake test indicates a sticking brake |3.3.C2c| | 1 |
Front Front suspension has inadequate damping effect. |2.3.6c| | 1 |
Front Brake lining|s| less than 1.5 mm thick |3.2.A1f|i|| | 1 |
Brake component is fractured front cable snapped |3.1.5| | 1 |
Front Brake locking device insecure |3.2.A1e| | 1 |
Rear Built up wheel has a bolt/s missing hub flange fractured |4.2.1c| | 1 |
Rear Position lamp not working |4.2.1 |a|| | 1 |
Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Fuel system component leaking excessively or a risk of fire (6.1.3 (b) (ii)) | 1 |
Stop lamp not working (4.3.1 (a) (ii)) | 1 |